DELTA 50-723 dust collector Instruction manual
The DELTA Industrial Model 50-723 Dust Collector will connect to woodworking machines that accept a 4” diameter hose.
advertisement
Assistant Bot
Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.
1 HP DUST COLLECTOR
1 HP Dépoussiéreur
Recolector de polvo de 1 HP
Français (20)
Español (40)
Instruction manual
Manuel d’utilisation
Manual de instrucciones
www.DeltaMachinery.com
INSTRUCTIVO DE OPERACIÓN, CENTROS
DE SERVICIO Y PÓLIZA DE GARANTÍA.
LÉASE ESTE INSTRUCTIVO
ANTES DE USAR EL PRODUCTO.
50-723
TABLE OF CONTENTS
IMPORTANT SAFETY INSTRUCTIONS .......................2
SAFETY GUIDELINES - DEFINITIONS ........................2
GENERAL SAFETY RULES ..........................................3
ADDITIONAL SPECIFIC SAFETY RULES ....................4
FUNCTIONAL DESCRIPTION ......................................6
CARTON CONTENTS ...................................................7
ASSEMBLY ....................................................................8
OPERATION ................................................................17
TROUBLESHOOTING .................................................17
MAINTENANCE ...........................................................18
SERVICE ......................................................................18
ACCESSORIES ............................................................19
FRANCAIS ...................................................................20
ESPANOL .....................................................................40
IMPORTANT SAFETY INSTRUCTIONS
Read and understand all warnings and operation instructions before using any tool or equipment. Always follow basic safety precautions to reduce the risk of personal injury. Improper operation, maintenance or modification of tools or equipment could result in serious injury and property damage.
There are certain applications for which tools and equipment are designed. This product should NOT be modified and/or used for any application other than for which it was designed.
If you have any questions relative to its application DO NOT use the product until you have written DELTA® Power
Equipment Corporation and we have advised you. Contact us online at www.DeltaMachinery.com or by mail at Technical
Service Manager, DELTA® Power Equipment Corporation, 99 Roush St. Anderson, SC 29625.
Information regarding the safe and proper operation of this tool is available from the following sources:
• Power Tool Institute, 1300 Sumner Avenue, Cleveland, OH 44115-2851or online at www.powertoolinstitute.com
• National Safety Council, 1121 Spring Lake Drive, Itasca, IL 60143-3201
• American National Standards Institute, 25 West 43rd Street, 4 floor, New York, NY 10036 www.ansi.org - ANSI 01.1
Safety Requirements for Woodworking Machines
• U.S. Department of Labor regulations www.osha.gov
SAVE THESE INSTRUCTIONS!
SAFETY GUIDELINES - DEFINITIONS
It is important for you to read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information.
indicates an imminently hazardous situation which, if not avoided,
will result in death or serious injury.
indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
indicates a potentially haz ard ous situation which, if not avoided, may result in minor or moderate injury.
used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in
property damage.
Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the state of california to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints,
• Crystalline silica from bricks and cement and other masonry products, and
• Arsenic and chromium from chemically-treated lumber (CCA).
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
2
GENERAL SAFETY RULES
Failure to follow these rules may result in serious personal injury.
1.
FOR YOUR OWN SAFETY, READ THE
INSTRUCTION MANUAL BEFORE OPERATING THE
MACHINE.
Learning the machine’s application, limitations, and specific hazards will greatly minimize the possibility of accidents and injury.
2. WEAR EYE AND HEARING PROTECTION. ALWAYS
USE SAFETY GLASSES. Everyday eyeglasses are NOT safety glasses. USE CERTIFIED SAFETY
EQUIPMENT.
Eye protection equipment should comply with ANSI Z87.1 standards. Hearing equipment should comply with ANSI S3.19 standards.
3. WEAR PROPER APPAREL.
Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts. Nonslip protective footwear is recommended. Wear protective hair covering to contain long hair.
4. DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT.
The use of power tools in damp or wet locations or in rain can cause shock or electrocution. Keep your work area well-lit to prevent tripping or placing arms, hands, and fingers in danger.
5. MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION.
Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories. Poorly maintained tools and machines can further damage the tool or machine and/or cause injury.
6. CHECK FOR DAMAGED PARTS.
Before using the machine, check for any damaged parts. Check for alignment of moving parts, binding of moving parts, breakage of parts, and any other conditions that may affect its operation. A guard or any other part that is damaged should be properly repaired or replaced with DELTA® or factory authorized replacement parts. Damaged parts can cause further damage to the machine and/or injury.
7. KEEP THE WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
8. KEEP CHILDREN AND VISITORS AWAY.
Your shop is a potentially dangerous environment. Children and visitors can be injured.
9. REDUCE THE RISK OF UNINTENTIONAL
STARTING.
Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury. Do not touch the plug’s metal prongs when unplugging or plugging in the cord.
10. USE THE GUARDS.
Check to see that all guards are in place, secured, and working correctly to prevent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE.
Tools, scrap pieces, and other debris can be thrown at high speed, causing injury.
12. USE THE RIGHT MACHINE.
Don’t force a machine or an attachment to do a job for which it was not designed.
Damage to the machine and/or injury may result.
13. USE RECOMMENDED ACCESSORIES.
The use of accessories and attachments not recommended by
DELTA® may cause damage to the machine or injury to the user.
14. USE THE PROPER EXTENSION CORD.
Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. See the Extension Cord Chart for the correct size depending on the cord length and nameplate ampere rating. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
15. SECURE THE WORKPIECE.
Use clamps or a vise to hold the workpiece when practical. Loss of control of a workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION
OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE.
Feeding it from the other direction will cause the workpiece to be thrown out at high speed.
17. DON’T FORCE THE WORKPIECE ON THE
MACHINE.
Damage to the machine and/or injury may result.
18. DON’T OVERREACH.
Loss of balance can make you fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE.
Injury could occur if the tool tips, or if you accidentally contact the cutting tool.
20.
NEVER LEAVE THE MACHINE RUNNING
UNATTENDED. TURN THE POWER OFF.
Don’t leave the machine until it comes to a complete stop. A child or visitor could be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT
THE MACHINE FROM THE POWER SOURCE before installing or removing accessories, changing cutters, adjusting or changing set-ups.
When making repairs, be sure to lock the start switch in the “OFF” position. An accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS.
The accidental start-up of a machine by a child or visitor could cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION.
A moment of inattention while operating power tools may result in injury.
24. USE OF THIS TOOL CAN GENERATE
AND DISBURSE DUST OR OTHER AIRBORNE
PARTICLES, INCLUDING WOOD DUST,
CRYSTALLINE SILICA DUST AND ASBESTOS
DUST.
Direct particles away from face and body. Always operate tool in well ventilated area and provide for proper dust removal. Use dust collection system wherever possible. Exposure to the dust may cause serious and permanent respiratory or other injury, including silicosis (a serious lung disease), cancer, and death. Avoid breathing the dust, and avoid prolonged contact with dust. Allowing dust to get into your mouth or eyes, or lay on your skin may promote absorption of harmful material. Always use properly fitting NIOSH/OSHA approved respiratory protection appropriate for the dust exposure, and wash exposed areas with soap and water.
3
ADDITIONAL SPECIFIC SAFETY RULES
Failure to follow these rules may result in serious personal injury.
DO NOT USE THIS UNIT TO FILTER
METAL DUST. Combining wood and metal dust can create an explosion or fire hazard. This unit is intended to filter non-explosive atmospheres only.
DO NOT USE THIS UNIT TO
DISSIPATE FUMES OR SMOKE. Explosions or fire can result. This dust collector is intended for use where only dry airborne dust is present. Its use should be limited to non-explosive, non-metallic atmospheres.
1. DO NOT OPERATE THIS UNIT UNTIL IT IS
COMPLETELY ASSEMBLED AND INSTALLED
ACCORDING TO THE INSTRUCTIONS. A unit incorrectly assembled can cause injury.
2.
OBTAIN ADVICE FROM YOUR SUPERVISOR, IN-
STRUCTOR, OR ANOTHER QUALIFIED PERSON if you are not thoroughly familiar with the operation of this unit. Knowledge is safety.
3. FOLLOW ALL WIRING CODES and recommended electrical connections to prevent electrical shock or electrocution.
4. DO NOT PULL THIS UNIT BY THE POWER CORD.
Do not allow the power cord to come in contact with sharp instruments or edges, hot surfaces, or oil or grease. Do not place any weight on top of the power cord. A damaged power cord can cause electrical shock or electrocution.
5.
SUPPORT THIS UNIT OR SECURELY CLAMP IT
TO THE WORK SURFACE WHEN IT IS USED IN
A PORTABLE APPLICATION to eliminate potential injury and/or damage from falling.
6.
ENSURE THAT THE INTAKE AND EXHAUST
AREAS ARE CLEAR PRIOR TO STARTING THE
UNIT. Clogged intakes or exhausts can cause an explosion and/or fire.
7. DO NOT USE THE DUST COLLECTOR to pick up flammable liquids such as gasoline. Do not use the dust collector near flammable or combustible liquids.
Explosion and/or fire can occur.
8.
KEEP ARMS, HANDS, AND FINGERS AWAY FROM
THE FAN. Avoid all exposure to rotating parts to prevent injury.
9.
DO NOT OPERATE THIS UNIT WITHOUT THE
DUST COLLECTION BAG IN PLACE AND
PROPERLY SECURED. Sawdust and other debris can provide the potential for fire and/or explosion and can also cause inhalation problems.
10. INSPECT THE DUST BAG FOR CUTS, RIPS, OR
TEARS. Replace damaged bags or vacuum hoses.
Sawdust and other debris can provide the potential for fire and/or explosion and can also cause inhalation problems.
11.
ALWAYS USE THE INTAKE CAPS TO COVER
UNUSED DUST PORTS. Debris can cause damage to the unit and injury.
12. DO NOT ATTEMPT TO REMOVE OR REPLACE the dust collection bag(s) while the unit is connected to the power source. Exposed fan blades can cause severe injuries.
13. MAINTAIN THE UNIT IN TOP CONDITION.
Clogged filters can increase the potential for fire or explosion. Follow all instructions for changing and cleaning filters.
14. STORE THIS UNIT IN A LOCATION that eliminates the potential for damage to the power cord. A damaged power cord can cause shock or electrocution. Safely store power cord on the unit to eliminate tripping hazards.
15.
TURN THE UNIT “OFF” AND DISCONNECT THE
UNIT from the power source before installing or removing accessories, before adjusting or changing set-ups, or when making repairs. An accidental start-up can cause serious injury.
16. TURN THE UNIT “OFF”, disconnect the unit from the power source, and clean the table/work area before leaving the area.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
4
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the machine to the power line, make sure the switch (s) is in the “OFF” position and be sure that the electric current is of the same characteristics as indicated on the machine. All line connections should make good contact. Running on low voltage will damage the machine.
Do not expose the machine to rain or operate the machine in damp locations.
MOTOR SPECIFICATIONS
Your machine is wired for 120V, 60 HZ alternating current. Before connecting the machine to the power source, make sure the switch is in the
“OFF” position.
GROUNDING INSTRUCTIONS
This machine must be grounded while in use to protect the operator from electric shock.
1. All grounded, cord-connected machines:
In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock. This machine is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
Do not modify the plug provided - if it will not fit the outlet, have the proper outlet installed by a qualified electrician. Improper connection of the equipment-grounding conductor can result in risk of electric shock. The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipmentgrounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipment-grounding conductor to a live terminal.
Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the machine is properly grounded.
Use only 3-wire extension cords that have 3-prong grounding type plugs and matching 3-conductor receptacles that accept the machine’s plug, as shown in Fig. A. Repair or replace damaged or worn cord immediately.
2. Grounded, cord-connected machines intended for use on a supply circuit having a nominal rating less than
150 volts:
If the machine is intended for use on a circuit that has an outlet that looks like the one illustrated in Fig. A, the machine will have a grounding plug that looks like the plug illustrated in Fig. A. A temporary adapter, which looks like the adapter illustrated in Fig. B, may be used to connect this plug to a matching 2-conductor receptacle as shown in Fig. B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. The green-colored rigid ear, lug, and the like, extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. Whenever the adapter is used, it must be held in place with a metal screw.
NOTE: In Canada, the use of a temporary adapter is not permitted by the Canadian Electric Code.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
CURRENT
CARRYING
PRONGS
GROUNDING MEANS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A Fig. B
5
3.
240 VOLT SINGLE PHASE OPERATION
The motor supplied with your machine is a dual voltage,
120/240 volt motor. It is shipped ready-to-run for 120 volt operation. However, it can be converted for 240 volt operation.
A qualified electrician should do the conversion, or the machine can be taken to an Authorized DELTA® Service
Center. When completed, the machine must conform to the National Electric Code and all local codes and ordinances.
The machine is converted by re-wiring the motor for 240 volts, installing a 240 volt plug on the power supply cord and replacing the switch with one that is rated for 240 volt operation.
Be sure the 240 volt plug is only used in an outlet having the same configuration as the plug illustrated in Fig. C.
No adapter should be used with the 240 volt plug.
In all cases, make certain that the receptacle in question is properly grounded. If you are not sure, have a qualified electrician check the receptacle.
EXTENSION CORDS
GROUNDED OUTLET BOX
CURRENT CARRYING
PRONGS
GROUNDING BLADE IS
LONGEST OF 3 BLADES
FIG. C
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 or D-2, shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
Volts
120
120
120
120
120
120
120
120
120
120
120
120
120
120
120
Total Length of
Cord in Feet up to
25
25-50
50-100
100-150 up to
25
25-50
50-100
100-150 up to
25
25-50
50-100
100-150
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG up to
25
25-50
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
0-6
0-6
0-6
0-6
6-10
6-10
6-10
6-10
10-12
10-12
10-12
10-12
12-16
12-16
12-16
Volts
240
240
240
240
240
240
240
240
240
240
240
240
240
240
240
Total Length of
Cord in Feet up to
50
50-100
100-200
200-300
Gauge of
Extension Cord
18 AWG
16 AWG
16 AWG
14 AWG up to
50
50-100
100-200
200-300 up to
50
50-100
100-200
200-300
18 AWG
16 AWG
14 AWG
12 AWG
16 AWG
16 AWG
14 AWG
12 AWG up to
50
50-100
14 AWG
12 AWG
GREATER THAN 100 FEET NOT RECOMMENDED
Fig. D-1 Fig. D-2
FUNCTIONAL DESCRIPTION
FOREWORD
The DELTA® Industrial Model 50-723 Dust Collector will connect to woodworking machines that accept a 4” diameter hose. The 50-723 comes with one 1 micron filter bag and two 6 mil plastic collection bag.
NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only.
6
1
CARTON CONTENTS
1. Blower Housing Assembly
4 2
2. Front Support Assembly
3. Base Frame
4. Rear Blower Housing Support (2)
5. Rear Stand Cross Support
4
5
6
11
8
3
7
9
12
10
6. Dust Collection PE Bag
7. Dust Filter Bag
8. Retainer Strap
9. Handle
10. Inlet Adapter
11. Dust Collection Bag Ring
12. Hanger Assembly
13
16
14
15
23
21
22
18
20
19
24 25 26
17
7
13. Rear Wheel (2)
14. M10 Hex Head Shoulder Bolt (2)
15. M12 Flat Washer
16. Swivel Casters (2)
17. Acorn Nuts (2)
18. M8 x 45 Hex Socket Head Screw (6)
19. M8 Flat Washer (4)
20. M8 Lock Nut (4)
21. Round Head Phillips Self-tapping screws (2)
22. Tube End Cap (2)
23. M6 x 10 Hex Socket Head Screw (2)
24. M8 x 55 Hex Socket Head Screw (2)
25. M5 Round Head Phillips Screw (2)
26. M6 x 40 Hex Socket Head Screw (2)
ASSEMBLY
For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual.
ASSEMBLY TIME ESTIMATE
30 minutes to 1 hour
This machine is heavy. Use two or more people when lifting.
ATTACHING THE CASTERS
1. Turn the base frame onto its side (Fig 1).
2. Insert threaded portion of caster into
through hole on the bottom of the base
frame.
3. Tighten acorn nut.
4. Repeat for the other caster.
FIGURE 1
ATTACHING THE REAR WHEELS
1. Place base frame upright.
2. Insert M12 flat washer onto shoulder bolt
(Fig 2).
3. Insert shoulder bolt through rear wheel.
4. Place another M12 flat washer between
wheel and base.
5. Tighten shoulder bolt.
6. Repeat for other wheel.
FIGURE 2
8
ASSEMBLY (continued)
ATTACHING REAR BLOWER
HOUSING SUPPORT
1. Place base frame on side.
2. Align Rear blower housing support with
through holes.
3. Insert M8 x 45mm hex socket head screw
through base support and base frame as
shown.
4. Place M8 flat washer and M8 lock nut on
bottom side (Fig 3).
5. Tighten lock nut.
6. Repeat for other side.
FIGURE 3
ATTACHING FRONT SUPPORT
ASSEMBLY
1. Place unit on its side.
2. Align front support assembly with through
holes at front of base frame.
3. Insert M8 x 45mm hex socket head screw
through hole in base frame and thread into
front support (Fig 4).
4. Tighten screw.
5. Repeat on other side.
FIGURE 4
ATTACHING REAR STAND CROSS
SUPPORT
1. Place unit upright.
2. Align rear stand cross support with through
hole on rear blower housing support.
3. Insert M6 hex socket head screw through
rear base support hole and thread into
cross support (Fig 5).
4. Tighten screw.
5. Repeat on other side.
FIGURE 5
9
ASSEMBLY (continued)
ATTACHING MOTOR BLOWER
ASSEMBLY TO STAND
NOTE: TWO PEOPLE ARE NEEDED FOR THIS STEP
1. Place motor blower assembly onto stand.
2. Align the brackets on the blower housing,
on the motor end, to the rear blower
housing supports.
3. Rear blower housing supports fit inside
the brackets on the blower housing, as
shown. (Fig 6)
FIGURE 6
4. Align holes on front support assembly to
blower housing assembly (Fig 7).
FIGURE 7
5. Insert M8 x 55mm hex socket head screw
through hole and thread into blower
housiing (Fig 8).
6. Tigten screw.
7. Repeat on other side .
FIGURE 8
10
ASSEMBLY (continued)
8. Place M6 hex socket head screw through
hole of blower housing bracket and
thread into rear blower housing support
(Fig 9).
9. Tigten screw.
10. Repeat on other side.
FIGURE 9
ATTACHING HANDLE
1. Insert handle into both brackets on blower
housing (Fig 10).
2. Align holes in handle with top holes
in blower housing brackets.
3. Screw in M8 Phillips head self tapping
screw on both sides (Fig 11).
4. Insert tube end cap into end of handle.
5. Be sure cap is seated (Fig 12).
6. Repeat on other side.
FIGURE 10
FIGURE 11
11
FIGURE 12
ASSEMBLY (continued)
ATTACHING THE DUST INTAKE PORTS
Disconnect the machine from the power source!
1. Place the inlet adapter on the dust intake port
as shown in Fig. 13 opposite to the motor.
Make sure that the inlet adapter fits on the
intake flange and holes line up between the
inlet adapter and housing.
2. Insert screws.
3. Tighten screws on both sides.
FIGURE 13
12
ASSEMBLY (continued)
ATTACHING THE
DUST COLLECTION BAG
Disconnect the machine from the power source!
A. USING CLOTH COVERED FLEXIBLE RING:
1. Place the cloth-covered bag retainer ring inside the opening of the clear plastic dust collection bag. Fold about 6 inches of the bag around the retainer ring (Fig 14).
2. Place the bag in the large hole in the blower housing assembly. Fit the retainer ring into the bottom groove. Bend and fold the ring to fit it into place. Flexible ring will fit into the bottom of the blower housing the same way as described for installation of the Micron bag in the top of the blower housing. Refer to Fig 18 & Fig
19 on pg 15.
3. Tug slightly on the bag to eliminate any slack and to make sure that the bag is secure and will not detach during collection.
FIGURE 14
B. USING A METAL BAG CLAMP
You can also attach the plastic bag to the outside of the dust collector using the included clamp
Fig 15.
1. Slide the bag under the hooks.
2. Place the clamp around the top of the
plastic bag. Folding over a few inches
of plastic bag over the clamp.
3. Secure the clamp making sure the
clamp isn’t over the hook.
FIGURE 15
13
ASSEMBLY (continued)
ATTACHING THE TOP FILTER BAG
Disconnect the machine from the power source!
1. Insert the hanger rod hook through the material on top of the filter bag (Fig 16).
FIGURE 16
2. Insert the assembled hanger rod assembly into
the hanger bracket ensuring that the lock
button is in place and secure as shown in
(Fig 17).
FIGURE 17
14
ASSEMBLY (continued)
3. Work the open end of the filter bag into the
top groove of the dust collector drum until
it is secure and sealed. Bend and fold, as
necessary, the internal bag retainer ring to fit
it into place as shown in Fig 18 & 19.
NOTE: Bag ring must fit into housing groove
completly to ensure a proper seal with no leaks.
FIGURE 18
FIGURE 19
15
ASSEMBLY (continued)
ATTACHING THE HOSE TO THE INTAKE PORT
Disconnect the machine from the power source!
Model 50-723 provides one 4” dust ports.
To attach the hose (
SOLD SEPARATELY):
Loosely attach the hose clamp around one end of the flexible hose (
Hose sold seper-
ately). Attach the hose to the dust intake
port. Tighten the hose clamp as shown in
Fig 20. Attach the remaining clamp to the other end of the flexible hose and to the woodworking machine.
NOTE: Do not operate the dust collector
without hose attached to the inlet adapter.
FIGURE 20
16
OPERATION
OPERATIONAL CONTROLS AND ADJUSTMENTS
For operator safety, do not operate the machine with any dust intake holes uncovered. The rotating fan, located inside the blower housing, is accessible through the dust intake port and can be hazardous.
Always wear proper apparel. Do not wear jewelry. Keep your fingers and all foreign objects out of the dust intake port. Follow the safety rules in this manual.
STARTING AND STOPPING THE DUST COLLECTOR
1. The on/off switch Fig. 21 is located on the motor housing. To turn the machine “ON”, move the switch up to the
“ON” position.
2. To turn the machine “OFF”, move the switch (A) down to the “OFF” position.
Make sure that the switch is in the “OFF” position before plugging in the power cord. In the event of a power failure, move the switch to the “OFF” position. An accidental start-up can cause injury.
LOCKING THE SWITCH IN THE “OFF” POSITION
IMPORTANT: When the tool is not in use, the switch should be locked in the “OFF” position to prevent
unauthorized use. To lock the machine, grasp the switch toggle Fig. 21 and pull it out of the switch. With the switch toggle removed (Fig 22), the switch will not operate. However, should the switch toggle be removed while the dust collector is running, the machine can be turned
“OFF,” but cannot be restarted without re-inserting the key in the toggle switch.
FIGURE 21 FIGURE 22
When using this dust collector, do not pick up anything that is burning, smoldering, or smoking
(matches, cigarettes, or hot ashes).
Do not use this unit to vacuum combustible explosive materials (coal, grain, or other finely- divided combustible material).
Do not use this unit to vacuum hazardous, toxic, or carcinogenic materials (asbestos, pesticide, or lead-based paint debris).
TROUBLESHOOTING
For assistance with your machine, visit our website at www.DeltaMachinery.com for a list of service centers or call the DELTA® Power Equipment Corporation help line at 1-800-223-7278.
17
MAINTENANCE
To reduce the risk of injury, turn unit off and disconnect it from power source before installing and removing accessories, before adjusting or when making repairs. An accidental start-up can cause personal injury.
KEEP MACHINE CLEAN
Periodically blow out all air passages with dry compressed air. All plastic parts should be cleaned with a soft damp cloth.
NEVER use solvents to clean plastic parts. They could possibly dissolve or otherwise damage the material. Wear certified safety equipment for eye, hearing and respiratory protection while using compressed air.
FAILURE TO START
Should your machine fail to start, check to make sure the prongs on the cord plug are making good contact in the outlet. Also, check for blown fuses or open circuit breakers in the line.
SERVICE
REPLACEMENT PARTS
Use only identical replacement parts. For a parts list or to order parts, visit our website at www.DeltaMachinery.com/ service. You can also order parts from your nearest factory-owned branch, Authorized Warranty Service Center or by calling Technical Service Manager at 1-800-223-7278 to receive personalized support from one of our highly-trained representatives.
FREE WARNING LABEL REPLACEMENT
If your warning labels become illegible or are missing, call 1-800-223-7278 for a free replacement.
SERVICE AND REPAIRS
All quality tools will eventually require servicing and/or replacement of parts. For information about DELTA® Power
Equipment Corporation, its factory-owned branches, or to locate an Authorized Warranty Service Center, visit our website at www.DeltaMachinery.com or call our Technical Service Manager at 1-800-223-7278. All repairs made by our service centers are fully guaranteed against defective material and workmanship. We cannot guarantee repairs made or attempted by others. By calling this number you can also find answers to most frequently asked questions.
You can also write to us for information at DELTA® Power Equipment Corporation, 99 Roush St. Anderson, South
Carolina 29625 - Attention:
Technical Service Manager. Be sure to include all of the information shown on the nameplate of your tool (model number, type, serial number, date code, etc.)
18
ACCESSORIES
Since accessories other than those offered by DELTA® have not been tested with this product, use of such accessories could be hazardous. For safest operation, only DELTA® recommended accessories should be used with this product.
A complete line of accessories is available from your DELTA® Supplier, DELTA® Factory Service Centers, and DELTA®
Authorized Service Centers. Please visit our Web Site www.DeltaMachinery.com for an online catalog or for the name of your nearest supplier.
WARRANTY
To register your tool for warranty service visit our website at www.DeltaMachinery.com.
Five Year Limited New Product Warranty
DELTA® will repair or replace, at its expense and at its option, any new DELTA® machine, machine part, or machine accessory which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product prepaid to a DELTA® factory service center or authorized service station with proof of purchase of the product within five years and provides DELTA® with reasonable opportunity to verify the alleged defect by inspection. For all refurbished DELTA® product, the warranty period is 180 days. DELTA® will not be responsible for any asserted defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by anyone other than an authorized DELTA® service facility or representative. Under no circumstances will DELTA® be liable for incidental or consequential damages resulting from defective products. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty is DELTA®’s sole warranty and sets forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by DELTA®. For further detail of warranty coverage and warranty repair information, visit www.DeltaMachinery.com or call 1-800-223-
7278. This warranty gives you specific legal rights and you may have other rights which vary in certain states or provinces.
LATIN AMERICA: This warranty does not apply to products sold in Latin America. For products sold in Latin America, see country specific warranty information contained in the packaging, call the local company or see website for warranty information.
19
99 Roush Street
Anderson, SC 29625
(800) 223-7278 www.DeltaMachinery.com
Copyright © 2015 DELTA® Power Equipment Corporation DPEC003309
Issued 4-1-2015
advertisement
Key Features
- 1 HP Dust Collector
- 4” dust ports
- 1 micron filter bag
- two 6 mil plastic collection bags