Delta Electronics TP02 Specifications

Delta Electronics TP02 Specifications
PANEL COMPONENT
EXPLANATION
Escape / Exit Key
Enter Key
http://www.delta.com.tw/industrialautomation/
Terminal Panels Series!
It is used to cancel an incorrect input, or to exit a programming step.
It is used to input a value or accept a programming command.
UP / Pg Up: It is used to increase the value or move up one page.
Pg Dn / DOWN: It is used to decrease the value or move down one page.
Left: This key is left direction key and it can be used to select the position of the
value.
Right: This key is right direction key and it can be used to select the position of
the value.
Arrow Keys
Instruction Sheet
Warning
3
3
3
3
3
3
3
F0 / 0: It is used as a constant 0, or the user can define it as function F0.
F1 / 1: It is used as a constant 1, or the user can define it as function F1.
F2 / 2: It is used as a constant 2, or the user can define it as function F2.
F3 / 3: It is used as a constant 3, or the user can define it as function F3.
F4 / 4: It is used as a constant 4, or the user can define it as function F4.
F5 / 5: It is used as a constant 5, or the user can define it as function F5.
F6 / 6: It is used as a constant 6, or the user can define it as function F6.
F7 / 7: It is used as a constant 7, or the user can define it as function F7.
F8 / 8: It is used as a constant 8, or the user can define it as function F8.
F9 / 9: It is used as a constant 9, or the user can define it as function F9.
Please read this instruction carefully before use.
Switch off the power before wiring.
The display panel of TP02 series is waterproof. But please prevent grease, corrosive liquids and sharp objects from
contacting the TP02 series.
The TP02 series require 24VDC input power. DO NOT connect input AC power supply to any of the RS-485
communication port; otherwise serious damage may occur. Check all the wiring again before switching
on the power.
DO NOT touch any terminal when the power is switched on. DO NOT touch any internal circuit in 1
minute after the power is switched off.
Make sure the groud terminal
is correctly grounded in order to prevent electromagnetic
interference.
Please use the fixed support accessory which is packed together with the product provided by Delta. DO
NOT tighten the screws out of the normal torque specifications; otherwise serious damage may occur.
Function Keys
Vertical view (Unit: mm)
1.6 Installation
Please insert TP02 series to the opening hole of panel and tighten the screws. However, if a firm mounting TP02
series to the panel is needed, please use the mounting fixed support accessory which is packed together with TP02
series, then insert the fixed support in the back and tighten the screws.
If the fixed support is not installed well, Delta will not guarantee the waterproof function. The screw torque
should be 4-5(kg-cm). DO NOT exceed this specification when tightening the screws; otherwise TP02 series may be
damaged. Please leave sufficient space (more than 50mm) around the unit for heat dissipation.
Do not install and mount TP02 series in the following environment.
h
A location subjected to Airborne dust, metallic particles, oil and smoke, corrosive or
flammable gases and liquids.
h
A location where temperature and humidity will exceed specifications.
h
A location where vibration and shock will exceed specifications.
1.4 Back Panel
™
X Introduction
RS-232
The flat surface should be a UL Type 4 "Indoor Use Only" enclosure or equivalent (IP65 / NEMA4). Please
refer to the figures below.
Thickness: 0.5~9.0mm
1.1 Model Explanation
Thank you for choosing Delta TP Series. TP02G-AS1 has the features of high resolution 160×32 dots. It provides
Extension port
multilingual display and two built-in communication ports, one is for RS-232 and the other is for RS-485. RS-232
and RS-485 can be used simultaneously. Besides, it also supports communication and alarm LED indicators. The
user can purchase program copy card (optional) to copy settings and programs quickly and save download time.
™ Nameplate Explanation
Production model
Power input spec.
Barcode and
serial number
Version
5 PIN terminal / Wire gauge: 12-24 AWG / Torque: 4.5 lb.-inch
MODEL :
TP02G-AS1
POWER INPUT : 24Vdc 3W
1.5 Dimension
Y Function Specifications
Front panel (unit: mm [inch])
VX.XX
ITEM
TP02GAS1W6050004
DELTA ELECTRONICS, INC
MADE IN XXXXXXX
Screen Type
Display Color
NOTE: The words of “MADE IN XXXXX” will be different due to the manufacturing location. Please refer to the actual product
for exact description.
Backlight
™ Model / Serial No. Explanation
TP02GAS 1 W 6 05 0004
TP 02 G - AS 1
Reserved
Reserved
T: Text mode
G: Graphic mode
Resolution
Display Range
Contrast Adjustment
Production serial number
Production weeks
Production year (2006)
Production plant
(W: Wuijang; T: Taoyuan)
LCD Spec.
Series name
Language / Font
Version
Production model
Font Size
Right side diagram (unit: mm [inch])
Back panel
1.2 Product Outline
RS-232 LED Indicator
(Yellow)
RS-485 LED Indicator
(Green)
Program Memory
Alarm LED Indicator
RS-232 LED Indicator
Displaying Area
Alarm LED Indicator (RED)
RS-485 LED Indicator
Function Keys
Serial Communication Port
RS-232 (COM1)
Escape / Exit Key
Arrow Keys
Mounting dimension (unit: mm [inch])
Extension Communication
Port
RS-485 (COM2)
Enter Key
1.3 Panel Function Explanation
PANEL COMPONENT
Alarm LED Indicator
(RED)
RS-232 LED Indicator
(Yellow)
RS-485 LED Indicator
(Green)
Displaying Area
Extension Interface
EXPLANATION
Status 1: When power is on, LED will blink slowly for three times.
Status 2: When there is an abnormal situation, LED will blink quickly along with
an alarm sound.
85
[3.35]
Battery Cover
5 PIN Removal Terminal
LED will blink when transmits program and communicates via RS-232.
LED will blink when communicates via RS-485.
Liquid Crystal Module display area. It is used to display current program status.
135~136.5[5.31~5.37]
Thickness Range 0.5~9mm
TP02G-AS1
STN-LCD
Monochromatic
The back-light automatic turn off time is 1 ~ 99 minutes (0 = do not turn off)
(The back-light life is about 50 thousand hours at 25°C)
160 x 32 dots
(W) x (H) = 72 x 22 (unit: mm)
15 levels of adjustment
ASCII: Alphanumeric (including European characters)
Taiwan: (Big 5 codes) Traditional Chinese Fonts
China: (GB2324-80 codes) Simplified Chinese Fonts
ASCII: 5 × 8, 8 × 8, 8 × 12, 8 × 16
1. Power on indication (Blink for three times)
2. Communication error alarm
3. Special indication by user programming
It will blink when transmitting program and communicating by using RS-232.
It will blink when communicating by using RS-485.
256KB flash memory
Unsynchronized transmission method: RS-232
Data length: 7 or 8 bits, Stop bits: 1 or 2 bits
Parity: None/Odd/Even, Transmission speed: 4,800bps ~115,200bps
RS-232: 9 PIN D-SUB male
Unsynchronized transmission method: RS-485
Data length: 7 or 8 bits, Stop bits: 1 or 2 bits
Parity: None/Odd/Even, Transmission speed: 4,800bps ~115,200bps
RS-485: 5 PIN removal terminal
1. Update firmware version
2. The slot for program copy card
DC 3V battery for HMI
Include DC 24V input and RS-485 communication input
Z Electrical Specifications
] Hardware Operation
When the user wants to startup TP02 series, a 24VDC power is needed. After applying 24VDC power to TP02
Specifications
TP02G-AS1
Display
Effective Display Area
Display Resolution
LCD Contrast Adjustment
LCD Backlight Type
Function / Numeric Keys
External Input Power
Memory Capacity
CPU
RAM of System
Communication Interface
Waterproof Class of Front
Panel
Operating Temperature for
Hardware
Storage Temperature for
Hardware
Monochromatic STN LCD
(W) x (H) = 72 x 22 (unit: mm)
160×32: ASCII: 5×8, 8×8, 8×12, 8×16
Shock
Radiated Emission
Electrostatic Discharge
Immunity
Radiated Immunity
Electrical Fast Transient
Weight / Dimensions
Cooling Method
series, it will enter into the startup display and then enter the user-designed program. Pressing Esc key and
holding on for 5 seconds can return to system menu. There are five selections in the system menu and are
SELECTIONS
Download Program
Upload Program
IP65 / NEMA4
Copy Program
0 ~ 50°C; 20 ~ 90﹪RH (non-condensing)
-20 ~ 60°C
5Hz≦f<9Hz = Continuous: 1.75mm / Occasional: 3.5mm
9Hz≦f≦150Hz = Continuous: 0.5g / Occasional: 1.0g
15g peak, 11ms duration, half-sine, three shocks in each direction per axis,
on 3 mutually perpendicular axes (total of 18 shocks)
CISPR11, Class A
EN61000-4-2
TP02 Settings
EN61000-4-3
EN61000-4-4
0.24kg; 147×97×35.5mm (Width(W) × Height(H) × Deep(D))
Natural Air Cooling
[ Program Copy Card
TP02 series provides Program Copy Card Function to copy user program, system function and passwords that is
different from the copy program. It is used to copy the whole HMI environment settings and application programs
to another HMI rapidly. Using Program Copy Card saves time and manpower. The operation is as follows.
™
Definition: Program Copy Card → PCC, TP Series → TP
PLC Connection
(TP→PCC)
Step 1
Step 2
Step 3
Step 4
™
(PCC→TP)
Turn the switch on the PCC to TP ÆPCC
Insert the PCC into the extension slot of TP
Input the power to TP
It will display “remove PCC” on the screen and
power on again.
Turn the switch on the PCC to PCCÆTP
Insert the PCC into the extension slot of TP
Input the power to TP
It will display “remove PCC” on the screen and
power on again.
HMI Display Message
Step 1
Step 2
Step 3
(TP→PCC)
(PCC→TP)
If the TP model type does not correspond with the
model type of program of PCC, TP will display “TP
series and PCC is different. Press Enter to
Confirm TP series→PCC. Press Esc to Exit”.
TP will display “TP→PCC series Please wait!”
during transmission.
TP will display “Please Remove the PCC and
Reboot” when transmission is completed.
If there is no program in PCC, TP will display “The
PCC is Empty. PCC→TP series is illegal”.
Execution
^
™
F1
F2
F3
F4
MINI DIN TERMINAL
9 PIN D-SUB
PC / TP CO M Port
25 PIN D-SUB female
2
Tx
Rx
3
GND 7
4
5
6
8
20
PLC COM1 Port
8 PIN MINI DIN
4
Rx
2
5
Tx
4
5
8
GND
8
1,2 5V
7
PC / TP COM Port
9 PIN D-SUB female
PLC COM1 Port
8 PIN MINI DIN
Tx
Rx
GND
™
3
2
5
7
8
1
4
6
4
5
8
1,2
Rx
Tx
GND
5V
8
3
6
1
2
5
1
4
7
3
6
The Pin definition of 9 PIN D-SUB
TP02 / 04G COM Port
RS-232 9 PIN D-SUB male
3
2
5
_
™
Tx
Rx
GND
Battery Life
Battery Life
Temperature (°C)
-20
0
20
60
Life (Year)
1.972
2.466
2.712
2.835
TO TP02 / 04G
9
5
1
6
6
1
5
9
9 PIN D-SUB
9 PIN D-SUB
PC COM Port
9 PIN D-SUB female
Rx
Tx
GND
™
Function Key
Use Method
F5
It just can be used to be constant 5.
F6
It just can be used to be constant 6.
F7
It just can be used to be constant 7.
It just can be used to be constant 8.
F9
It just can be used to be constant 9.
3
2
5
Tx
Rx
GND
1. DVPACAB215 / DVPACAB230
TO PC or TP02 / 04G
13
F8
2
3
5
TP02 / 04G COM Port
9 PIN D-SUB female
TP02G may connect to a DVP-PLC by using connection cable DVPACAB215 / DVPACAB230 /
DVPACAB2A30
The password can be the alphabet from A to Z or the number from 0 to 9. But it must use the function
keys F0 ~ F9 to input the password characters. Please refer to the following table.
scrolls in a loop as follows
0→A→B→C→D→E→F→0
scrolls in a loop as follows
1→G→H→I→J→K→1
scrolls in a loop as follows
2→L→M→N→O→P→2
scrolls in a loop as follows
3→Q→R→S→T→U→ V→3
scrolls in a loop as follows
4→W→X→Y→Z→4
EXPLANAION
Use the connection cable (DVPACAB530) to connect the TP02 serial communication
port RS-232 to a PC. Then use the TPEdit software to download an application
program to TP02.
Use the connection cable (DVPACAB530) to connect the TP02 serial communication
port RS-232 to a PC. Then use the TPEdit software to upload an application
program from TP02.
Transfer a program between two TP02 units.
1: transmit programs
2: receive programs
When transmit programs and data between two TP02 units. Set one TP02 to
“Receive Program” mode and the other TP02 to “Transmit Program” mode. Please
use twisted pair wires to connect the two units via the RS-485 ports.
There are 8 items that used to modify TP02 system settings:
1. Communication protocol: Setting the address of TP02, the control port of PLC,
and the communication string for either RS-232 or RS-485.
2. Contrast: Adjust the contrast of LCM display screen.
3. Back-light: adjust the automatic turn off time of LCM. Setting range is 00 ~ 99
minutes. If set to 00, the LCM Back-light will not turn off.
4. Buzzer: Used to set the buzzer sound, normal mode or quiet mode.
5. Language Setting: Used to set the displayed language. English, Traditional
Chinese, Simplified Chinese or user defined language.
6. Password setting: Used to set, enable, and disable the password function. If the
password function is enabled, it will require the user to input a password before
entering any system menu. The factory password is 1234.
7. Startup display: Used to select the TP02 startup display. User can select “user
defined” to use the file that designed by TPEdit and download to TP02.
8. Comm. indicator: The user can determine if the RS-232 and RS-485 LEDs will
blink or not during communication.
There are two methods to connect to PLC:
1. Using TP02 serial communication port (COM1) RS-232: set 8-pin DIP switch to
RS-485 mode and connect the cable (DVPACAB215 or DVPACAB230) to
program communication I/O RS-232C of PLC.
2. Using extension communication port (COM2) RS-485: set 8-pin DIP switch to
RS-485 mode and connect 5-pin removal terminal of extension communication
port to RS-485 of PLC with twisted pair.
Execute the internal program that download from TPEdit or transmitted from other
TP02 units. When program is in execution, the user can return to system menu by
pressing Escape / Exit (Esc) key for 5 seconds.
TO PC (RS-232)
TP will display “PCC→TP series Please wait!”
during transmission.
TP will display “Please Remove the PCC and
Reboot” when transmission is completed.
settings by using this code also. Please pay close attention when using it.
F0
1
TP02G may connect to a PC by using connection able DVPACAB515
code will clear the password and all TP02 series internal programs. The TP02 series will be reset to the factory
Use Method
6
TO PLC
Communication Connection
If the user forgot the password, the password can be cleared by using the following code: 8888. This universal
Function Key
5
PC or TP02 / 04G
\ Password Function
™
TO PC or TP02 / 04G
9
described below.
Set by Software, adjust the contrast by the press button in the function table
LED Backlight: Automatic Turn-off Setting
F0 / 0 ~ F9 / 9, ESC, ENTER and Arrow Keys
24V (3W Max.)
256K Byte
Hitachi HD64F3064F
32K Byte
COM1: RS-232 COM2: RS-485
Vibration
2. DVPACAB2A30
14
1
9
5
6
1
25 PIN D-SUB
TO PLC
MINI DIN TERMINAL
9 PIN D-SUB
The content of this instruction sheet may be revised without prior notice. Please consult our distributors or
download the most updated version at http://www.delta.com.tw/industrialautomation
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement