Drill Master 91938 14 in. 2 HP Cut-Off Saw Owner's Manual & Safety Instructions
Advertisement
Advertisement
Owner’s Manual & Safety Instructions
Save This Manual
Keep this manual for the safety warnings and precautions, assembly, operating, inspection, maintenance and cleaning procedures. Write the product’s serial number in the back of the manual near the assembly diagram (or month and year of purchase if product has no number).
Keep this manual and the receipt in a safe and dry place for future reference.
REV 15i
Cut-Off Wheel sold separately.
Visit our website at: http://www.harborfreight.com
Email our technical support at: [email protected]
When unpacking, make sure that the product is intact and undamaged. If any parts are missing or broken, please call 1-888-866-5797 as soon as possible.
Copyright
©
2004 by Harbor Freight Tools
®
. All rights reserved.
No portion of this manual or any artwork contained herein may be reproduced in any shape or form without the express written consent of Harbor Freight Tools.
Diagrams within this manual may not be drawn proportionally. Due to continuing improvements, actual product may differ slightly from the product described herein.
Tools required for assembly and service may not be included.
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAL.
Table of Contents
Safety ......................................................... 2
Specifications ............................................. 7
Setup .......................................................... 7
Operation .................................................... 8
Maintenance .............................................. 12
Parts List and Diagram .............................. 14
Warranty .................................................... 16
WARNING SyMBOLS AND DEFINITIONS
This is the safety alert symbol. It is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death.
Indicates a hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury.
Addresses practices not related to personal injury.
IMpORTANT SAFETy INFORMATION
General Tool Safety Warnings
WARNING Read all safety warnings and instructions.
Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
1. KEEP GUARDS IN PLACE and in working order.
2. REMOVE ADJUSTING KEYS AND
WRENCHES. Form habit of checking to see that keys and adjusting wrenches are removed from tool before turning it on.
5. KEEP CHILDREN AWAY. All visitors should be kept safe distance from work area.
6. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys.
3. KEEP WORK AREA CLEAN.
Cluttered areas and benches invite accidents.
4. DON’T USE IN DANGEROUS ENVIRONMENT.
Don’t use power tools in damp or wet locations, or expose them to rain. Keep work area well lighted.
7. DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was designed.
8. USE RIGHT TOOL. Don’t force tool or attachment to do a job for which it was not designed.
Page 2
For technical questions, please call 1-888-866-5797.
Item 91938
General Tool Safety Warnings (cont.)
TABLE A: RECOMMENDED MINIMUM WIRE
GAUGE FOR EXTENSION CORDS
(120 VOLT)
NAMEpLATE
AMpERES
(at full load)
0 – 6
EXTENSION CORD
LENGTH
25′
18
50′ 100′ 150′
16 16 14
6.1 – 10
10.1 – 12
12.1 – 16
18
16
14
16
16
12
14
14
12
12
Do not use.
13. DON’T OVERREACH.
Keep proper footing and balance at all times.
14. MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for best and safest performance. Follow instructions for lubricating and changing accessories.
15. DISCONNECT TOOLS before servicing; when changing accessories, such as blades, bits, cutters, and the like.
9. USE PROPER EXTENSION CORD. Make sure your extension cord is in good condition. When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating.
Table A shows the correct size to use depending on cord length and nameplate ampere rating.
If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord.
10. WEAR PROPER APPAREL. Do not wear loose clothing, gloves, neckties, rings, bracelets, or other jewelry which may get caught in moving parts.
Nonslip footwear is recommended.
Wear protective hair covering to contain long hair.
11. ALWAYS USE SAFETY GLASSES. Also use face or dust mask if cutting operation is dusty.
Everyday eyeglasses only have impact resistant lenses, they are NOT safety glasses.
12. SECURE WORK. Use vise to hold work when practical. It’s safer than using your hand and it frees both hands to operate tool.
16. REDUCE THE RISK OF UNINTENTIONAL
STARTING. Make sure switch is in off position before plugging in.
17. USE RECOMMENDED ACCESSORIES.
Consult the owner’s manual for recommended accessories. The use of improper accessories may cause risk of injury to persons.
18. NEVER STAND ON TOOL.
Serious injury could occur if the tool is tipped or if the cutting tool is unintentionally contacted.
19. CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced.
20. NEVER LEAVE TOOL RUNNING
UNATTENDED. TURN POWER OFF. Don’t leave tool until it comes to a complete stop.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 3
Grounding Instructions
TO pREVENT ELECTRIC SHOCK AND DEATH FROM INCORRECT GROUNDING WIRE
CONNECTION
READ AND FOLLOW THESE INSTRUCTIONS:
110-120 VAC Grounded Tools: Tools with Three prong plugs
1. In the event of a malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of electric shock.
This tool is equipped with an electric cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into a matching outlet that is properly installed and grounded in accordance with all local codes and ordinances.
2. Do not modify the plug provided – if it will not fit the outlet, have the proper outlet installed by a qualified electrician.
3. Improper connection of the equipment-grounding conductor can result in a risk of electric shock.
The conductor with insulation having an outer surface that is green with or without yellow stripes is the equipment-grounding conductor. If repair or replacement of the electric cord or plug is necessary, do not connect the equipmentgrounding conductor to a live terminal.
4. Check with a qualified electrician or service personnel if the grounding instructions are not completely understood, or if in doubt as to whether the tool is properly grounded.
5. Use only 3-wire extension cords that have 3-prong grounding plugs and 3-pole receptacles that accept the tool’s plug.
6. Repair or replace damaged or worn cord immediately.
Grounding pin
125 VAC 3-prong plug and Outlet
(for up to 125 VAC and up to 15 A)
7. This tool is intended for use on a circuit that has an outlet that looks like the one illustrated above in
125 VAC 3-prong plug and Outlet. The tool has a grounding plug that looks like the plug illustrated above in 125 VAC 3-prong plug and Outlet.
8. The outlet must be properly installed and grounded in accordance with all codes and ordinances.
9. Do not use an adapter to connect this tool to a different outlet.
Page 4
For technical questions, please call 1-888-866-5797.
Item 91938
Cut-Off Saw Safety Warnings
For your Own Safety Read Instruction
Manual Before Operating Cut-Off Saw
1. Check Swing Guard (53) for proper closing before each use. Do not operate the Saw if the Swing
Guard does not move freely and close instantly.
Never clamp or tie the Swing Guard into the open position. If the saw is accidently dropped, the Swing
Guard may be bent. Raise the Swing Guard and make sure it moves freely and does not touch the
Cut-Off Wheel or another part, in all depths of cut.
2. The Swing Guard should be retracted manually only for special cuts such as “Pocket Cuts” and
“Compound Cuts.” Raise the Swing Guard only enough to begin the cut. As soon as the cut-off wheel enters the material, the Swing Guard must be released. For all other sawing, the Swing Guard should be allowed to operate automatically.
3. The Saw is not to be used for any cutting in the locked down position. The Saw should be locked down position only for carrying and storage.
4. Always use cut‑off wheels with a 14″ diameter,
1″ arbor hole, and rated at a minimum of 3,500 RPM.
Cut-off wheels that do not match the mounting hardware of the Saw or that are rated at less than the Saw’s maximum RPM may fly off the Saw or may run eccentrically, causing loss of control.
5. Never use damaged or incorrect cut-off wheel washers or bolts. The cut-off wheel’s washers and bolts were specially designed for your Saw, for optimum performance and safety of operation.
6. Do not use the cut-off wheel (sold separately) to cut aluminum, copper, brass, or other non-ferrous metals. The cut-off wheel is designed to cut only ferrous (iron containing) metals such as steel alloys and cast iron.
If using other cut-off wheels, only use them on materials that the manufacturer recommends.
7. Before using the Cut-Off Saw, make sure the cut-off wheel is properly mounted on the saw spindle. Make sure the cut-off wheel is balanced and is not broken or bent.
8. Wear eye protection.
9. Use grinding wheel suitable for speed of cut-off wheel.
10. Replace cracked wheel immediately.
11. Do not overtighten wheel nut.
12. Use only flanges furnished with the Cut-Off saw.
13. Frequently clean grinding dust from beneath Cut-Off saw.
14. Wear a full face shield over ANSI-approved safety goggles during use.
15.
DO NOT OpERATE WITH ANy GUARD
DISABLED, DAMAGED, OR REMOVED. Moving guards must move freely and close instantly.
16. The use of accessories or attachments not recommended by the manufacturer may result in a risk of injury to persons.
17. When servicing use only identical replacement parts.
18. Only use safety equipment that has been approved by an appropriate standards agency. Unapproved safety equipment may not provide adequate protection. Eye protection must be ANSI-approved and breathing protection must be NIOSH-approved for the specific hazards in the work area.
19. Industrial applications must follow OSHA guidelines.
20. Maintain labels and nameplates on the tool.
These carry important safety information.
If unreadable or missing, contact
Harbor Freight Tools for a replacement.
21. Avoid unintentional starting.
Prepare to begin work before turning on the tool.
22. People with pacemakers should consult their physician(s) before use. Electromagnetic fields in close proximity to heart pacemaker could cause pacemaker interference or pacemaker failure.
23. WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. Some examples of these chemicals are:
• Lead from lead-based paints
• Crystalline silica from bricks and cement or other masonry products
• Arsenic and chromium from chemically treated lumber
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code § 25249.5, et seq.)
24. WARNING: The cord of this product contains lead and/or di (2-ethylhexyl) phthalate (DEHP), chemicals known to the State of California to cause cancer, and birth defects or other reproductive harm. Wash hands after handling.
(California Health & Safety Code § 25249.5, et seq.)
25. The warnings, precautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that may occur. It must be understood by the operator that common sense and caution are factors which cannot be built into this product, but must be supplied by the operator.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 5
Vibration Safety
This tool vibrates during use. Repeated or long-term exposure to vibration may cause temporary or permanent physical injury, particularly to the hands, arms and shoulders. To reduce the risk of vibration-related injury:
1. Anyone using vibrating tools regularly or for an extended period should first be examined by a doctor and then have regular medical checkups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, nervous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible.
2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury.
3. Wear suitable gloves to reduce the vibration effects on the user.
4. Use tools with the lowest vibration when there is a choice between different processes.
5. Include vibration-free periods each day of work.
6. Grip tool as lightly as possible (while still keeping safe control of it). Let the tool do the work.
7. To reduce vibration, maintain the tool as explained in this manual. If any abnormal vibration occurs, stop use immediately.
SAVE THESE INSTRUCTIONS.
Page 6
For technical questions, please call 1-888-866-5797.
Item 91938
Specifications
Electrical Input
Motor No Load Speed
Max. Accessory Diameter 14″
Recommended Cut-Off
Wheel Types
Cutting Capacity
Quick Release
Vise Capacities
Arbor Size
120VAC / 60Hz / 15A
3,500 RPM
14″ Cut‑Off Wheel for Metal (Item 44814, sold separately)
14″ Cut‑Off Wheel for Masonry (Item 44815, sold separately)
4‑1/4″
7″ (1st Setting),
9‑1/2″ (2nd Setting)
1″
5001571
Setup - Before Use
Functions
Handle
(100,109)
Motor
Housing
(75)
Base (13)
Item 91938
Trigger (103)
Vise Handle (28)
Lock
Lock Ball (25)
Depth
Adjustment
Bolt (16)
For technical questions, please call 1-888-866-5797.
Nut (15)
Page 7
Operating Instructions
Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this manual including all text under subheadings therein before set up or use of this product.
Tool Set Up
TO pREVENT SERIOUS INJURy FROM ACCIDENTAL OpERATION:
Release the Trigger, unplug the tool from its electrical outlet and allow the wheel to cool completely before performing any inspection, maintenance, or cleaning procedures.
To Remove or Install a Cut-Off Wheel
1. Raise the Saw if it is locked down by pushing down on it and pulling out the Lock Ball (25).
2. Open the Swing Guard (53) and tighten the Bolt (112) to secure it while working on the Wheel.
3. Push the Lock Pin (63) towards the
Fixed Guard (60) as shown in Figure A. Rotate the wheel until the Lock Pin (63) slides into place.
Lock pin
(63)
4. While continuing to hold down the Lock Pin (63), use the Hex Key (111a) to loosen the
Socket Head Bolt (54). See
Figure B.
Lock pin (63)
Socket Head
Bolt (54)
Hex Key
(111a)
Handle
Fixed
Guard (60)
Figure B: Socket Head Bolt
Figure A: Lock pin
Page 8
For technical questions, please call 1-888-866-5797.
Item 91938
Tool Set Up (cont’d)
5. Remove the Socket Head Bolt (54), the Flange Washer (96), the Outer Flange (55), and the cut-off wheel (sold separately). See
Figure C.
Socket Head
Bolt (54)
Flange
Washer (96)
Outer
Flange (55)
Depth Adjustment
Note: The Cutting Depth will need to be adjusted whenever a worn down wheel is replaced with a new one.
1. Loosen the Nut (15) on the Depth
Adjustment Bolt (16) shown in Figure D.
Cut-Off Wheel
Inner Flange (57)
Figure C: Cut-Off Wheel Hardware
6. Replace with a new cut-off wheel, and reassemble the parts listed above in number 5. The concave side of the Outer Flange (55) must face the wheel. While holding the Lock Pin (63), tighten the
Socket Head Bolt (54) with the Hex Key (111a).
7.
LOOSEN THE BOLT (112) and make sure that the Swing Guard (53) moves freely back into place before operation.
Depth
Adjustment
Bolt (16)
Nut (15)
Figure D: Depth Adjustment
2. Turn the Depth Adjustment Bolt (16) to change the depth so that the wheel will not contact the base at any time during cutting.
3. After adjustment, tighten the Nut (15) against the
Bracket (14) to lock the adjustment in place.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 9
Work piece and Work Area Set Up
1. Designate a work area that is clean and well-lit.
The work area must not allow access by children or pets to prevent distraction and injury.
2. Route the power cord along a safe route to reach the work area without creating a tripping hazard or exposing the power cord to possible damage. The power cord must reach the work area with enough extra length to allow free movement while working.
3. Secure loose work pieces using the vise to prevent movement while working: a. To use the Quick Release (31), put the Quick
Release (31) tab in the position shown in
Figure E and push the Vise Handle (28) up against the workpiece. Then tighten the
Vise Handle (28). When releasing, loosen the
Vise Handle (28) a few turns, lift up the Quick
Release (31), and pull the Vise Handle (28) open.
Quick
Release (31) place Workpiece
Here
b. To cut at various angles (up to 45º), adjust the Angle Scale (35) by loosening the two Bolts (41 & 44) as shown in
Figure F.
Adjust the Angle Scale to the desired setting and then tighten the Bolts (41 & 44).
Upper Two
Screw Holes
Bolts (41 & 44)
Angle Scale (35)
Figure F: Angle Scale
c. To reposition the Angle Scale (35), remove both of the Bolts (41 & 44), and reattach the Angle Scale at the upper two screw holes. See Figure E.
4. There must not be objects, such as utility lines, nearby that will present a hazard while working.
Vise Handle (28)
Figure E: Vise Components
Page 10
For technical questions, please call 1-888-866-5797.
Item 91938
General Operating Instructions
TO pREVENT SERIOUS INJURy:
DO NOT OpERATE WITH ANy GUARD DISABLED, DAMAGED, OR REMOVED.
Moving guards must move freely and close instantly. Bolt (112) MUST be loose before operation.
1. Using the vise, secure your workpiece and, if necessary, adjust the angle of the cut.
6. Repeat the cutting process starting with number 1 above.
2. Raise the Saw by pushing down on it and pulling out the Lock Ball (25).
3. Plug the Power Cord into the nearest 120 VAC, grounded, electrical outlet. Slide the Trigger
Lock and pull the Trigger to start the Saw.
Allow the cut-off wheel to attain full speed.
7. Once the cut is completed, turn off the Saw by releasing the Trigger and unplug the unit.
Do not attempt to remove the workpiece until the cut-off wheel has stopped moving.
8. To prevent accidents, turn off the tool, disconnect its power supply, and lock it down by pushing it down as far as it will go, and then pushing the Lock Ball (25) in after use. Clean, then store the tool indoors out of children’s reach.
4. With one hand on the Handle and the other hand clear, slowly bring the Saw down onto the Base, letting the Saw do the work.
Do not apply excessive force.
5. If the cut-off wheel does not cut all the way through the workpiece, raise the Saw and release the Trigger. Unplug the unit. Wait until the unit comes to a full stop. Remove the workpiece.
Set the depth adjustment to a deeper setting.
After adjusting the depth, bring the Saw all the way down to make sure the cut-off wheel doesn’t contact the Base. If it does contact any part of the Base, re-adjust the depth so it doesn’t.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 11
Maintenance and Servicing
procedures not specifically explained in this manual must be performed only by a qualified technician.
TO pREVENT SERIOUS INJURy FROM ACCIDENTAL OpERATION:
Release the Trigger, unplug the tool from its electrical outlet and allow the wheel to cool completely before performing any inspection, maintenance, or cleaning procedures.
TO pREVENT SERIOUS INJURy FROM TOOL FAILURE:
Do not use damaged equipment. If abnormal noise or vibration occurs, have the problem corrected before further use.
Cleaning, Maintenance, and Lubrication
1. BEFORE EACH USE, inspect the general condition of the tool. Check for loose hardware, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation.
2. AFTER USE, wipe external surfaces of the tool with clean cloth.
3.
WARNING! If the supply cord of this power tool is damaged, it must be replaced only by a qualified service technician.
Page 12
For technical questions, please call 1-888-866-5797.
Item 91938
Troubleshooting problem
Tool will not start.
possible Causes
1. Cord not connected.
2. No power at outlet.
Likely Solutions
1. Check that cord is plugged in.
2. Check power at outlet. If outlet is unpowered, turn off tool and check circuit breaker.
If breaker is tripped, make sure circuit is right capacity for tool and circuit has no other loads.
3. Tool’s thermal reset breaker tripped (if equipped).
4. Internal damage or wear.
(Carbon brushes or switch, for example.)
Tool operates slowly. Extension cord too long or wire size too small.
4. Have technician service tool.
Eliminate use of extension cord. If an extension cord is needed, use shorter/heavier gauge cord.
See Extension Cords in GROUNDING section.
Carbon brushes worn or damaged. Have qualified technician replace brushes.
Performance decreases over time.
Excessive noise or rattling.
Overheating.
Internal damage or wear. (Carbon brushes or bearings, for example.)
1. Forcing machine to work too fast.
Have technician service tool.
1. Allow machine to work at its own rate.
2. Accessory misaligned.
3. Turn off tool and allow to cool.
Press reset button on tool.
3. Blocked motor housing vents.
2. Check and correct accessory to fence and/or table alignment.
3. Wear ANSI-approved safety goggles and NIOSHapproved dust mask/respirator while blowing dust out of motor using compressed air.
4. Motor being strained by long or small diameter extension cord.
4. Eliminate use of extension cord.
If an extension cord is needed, use one with the proper diameter for its length and load.
See Extension Cords in GROUNDING section.
Follow all safety precautions whenever diagnosing or servicing the tool.
Disconnect power supply before service.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 13
parts List and Diagram pLEASE READ THE FOLLOWING CAREFULLy
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM
IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS
QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR THAT HE OR SHE IS QUALIFIED TO REPLACE
ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND
LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY
ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS
THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.
parts List part Description
1
Bolt M6x14
2 Lock Nut
3 Dust Cover
4 Bolt M5x12
5 Lock Nut M6
6 Nut M10
7 Nut M10
8 Binding Ring
9 Washer
10 Nut M8
11 Bolt 4-M6x24
12 Rubber Foot
13 Base
14 Bracket
15 Nut M8
16 Depth Adjustment Bolt
17 Screw
18 Lock Nut M6
19 Bolt 2-M5x10
21 Lock Down Pin
22 Rubber Gasket
23 Rubber Gasket
24 Binding Ring
25 Lock Ball
26 Roll Pin
27 Thread Bar
28 Vise Handle
29 Handle Pin
30 Vise Base
31 Quick Release
32 Lock Washer
33 Screw
34 Sliding Jaw
35 Angle Scale
part Description
36 Straight Pin
37 Washer
38 Binding Ring
39 Washer
40 Pin
41 Bolt M10x20
42 Lock Washer
43 Washer
44 Bolt M10x20
45 Lock Washer
46 Washer
53 Swing Guard
54 Socket Head Bolt
55 Outer Flange
56 Cut-Off Wheel
(sold separately)
57 Inner Flange
58 Screw
59 Lock Washer
60 Fixed Guard
61 Arbor
62 Spring
63 Lock Pin
64 Bolt 2-M5x54
65 Lock Washer
66 Carbon Brush Holder
67 Carbon Brush
68 Carbon Brush Cover
69 Bolt 2-M5x10
70 Cover
71 Bolt 2-M5x10
72 Screw M4x10
73 Lock Washer
part Description
74 Washer
75 Motor Housing
76 Spring
77 Binding Ring
78 Cross Pin
81 Binding Ring
82 Stator
83 Circle Block
84 Bearing
85 Armature
86 Bearing
87 Middle Cover
88 Bearing Ring
89 Binding Ring
90 Gear
91 Front cover
92 Bearing
93 Half Washer
96 Flange Washer
97 Nut M6
98 Bolt M6x10
99 Nut M4
100 Left Handle
101 Nut M5
103 Trigger with Lock
104 Screw
105 Wire Board
106 Sheathing
107 Power Cord
108 Screw
109 Right Handle
110 Bolt 3-M5x50
111a Hex Key
112 Socket Head Bolt
Record product’s Serial Number Here:
Note: If product has no serial number, record month and year of purchase instead.
Note: Some parts are listed and shown for illustration purposes only, and are not available individually as replacement parts.
Page 14
For technical questions, please call 1-888-866-5797.
Item 91938
Assembly Diagram
Note: Hex Key (111a) - not shown.
Item 91938
For technical questions, please call 1-888-866-5797.
Page 15
Limited 90 Day Warranty
Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installation, normal wear and tear, or to lack of maintenance. We shall in no event be liable for death, injuries to persons or property, or for incidental, contingent, special or consequential damages arising from the use of our product. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitation of exclusion may not apply to you. THIS WARRANTY IS EXPRESSLY IN LIEU OF ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS.
To take advantage of this warranty, the product or part must be returned to us with transportation charges prepaid. Proof of purchase date and an explanation of the complaint must accompany the merchandise.
If our inspection verifies the defect, we will either repair or replace the product at our election or we may elect to refund the purchase price if we cannot readily and quickly provide you with a replacement. We will return repaired products at our expense, but if we determine there is no defect, or that the defect resulted from causes not within the scope of our warranty, then you must bear the cost of returning the product.
This warranty gives you specific legal rights and you may also have other rights which vary from state to state.
3491 Mission Oaks Blvd. • pO Box 6009 • Camarillo, CA 93011 • 1-888-866-5797
Public link updated
The public link to your chat has been updated.
Advertisement
