5M-IR / PIR 720P HD H.264 CMOS Network Camera User’s Manual

5M-IR / PIR 720P HD
H.264 CMOS Network Camera
CAM6716H / CAM6716H-W / CAM6716H-PoE
User’s Manual
Date: 5/10/2014
Firmware Version: VE1.0.14
Content
Content ....................................................................................................................................... 1
1.
Preface ................................................................................................................................. 3
2.
Product Specifications ....................................................................................................... 3
3.
Product Installation ............................................................................................................ 6
A.
Hardware Installation ...................................................................................................... 6
Cable Connections................................................................................................................ 6
I/O Connections .................................................................................................................... 8
B.
Monitor Setting .............................................................................................................. 10
C.
IP Assignment................................................................................................................ 11
4.
Live Video .......................................................................................................................... 13
5.
Configuration .................................................................................................................... 16
A.
System ........................................................................................................................... 16
System Information ............................................................................................................. 16
User Management .............................................................................................................. 20
System Upgrade ................................................................................................................. 22
System Logs ....................................................................................................................... 23
B.
Video/Audio Setting ...................................................................................................... 24
Video Format ...................................................................................................................... 24
Image Setting ...................................................................................................................... 30
Audio Setting ...................................................................................................................... 33
C.
Network Setting ............................................................................................................. 35
Network Setting .................................................................................................................. 35
Wireless Setting .................................................................................................................. 40
Mail / FTP / Samba Setting ................................................................................................. 43
PPPoE / DDNS Setting ....................................................................................................... 47
D.
Network (Advance) Setting ........................................................................................... 50
HTTPS Setting .................................................................................................................... 50
SNMP Setting ..................................................................................................................... 52
IP Filter Setting ................................................................................................................... 54
QoS/ DSCP Setting............................................................................................................. 56
IEEE 802.1x Setting ............................................................................................................ 57
1
E.
Event Handling .............................................................................................................. 58
Event Setting ...................................................................................................................... 58
I/O Setting ........................................................................................................................... 66
Schedule ............................................................................................................................. 68
Micro-SD Card .................................................................................................................... 70
6.
Network Configuration ..................................................................................................... 72
A.
Intranet Only .................................................................................................................. 72
Connects to PC Directly ...................................................................................................... 72
Connects to an Exist LAN ................................................................................................... 73
B.
Internet Only .................................................................................................................. 74
Connects to ADSL with Fixed Public IP Address ................................................................. 74
Connects to ADSL with Floating Public IP Address (PPPoE) .............................................. 75
C.
Intranet + Internet .......................................................................................................... 77
Connects to Internet with Fixed Public IP Address.............................................................. 77
Connects to Internet with Floating Public IP Address.......................................................... 79
7.
Factory Default .................................................................................................................. 80
Compatible List of SD Card ..................................................................................................... 81
2
1. Preface
This camera is a 720P HD CMOS network camera which builds in web server. User views
real-time video via IE browser. It supports H.264 and MJPEG video compression which
provides smooth and high quality video. The event video can be stored in the Micro-SD
card, and can be playback remotely.
This camera equips infrared illuminator to provide good image quality, even in darkness. It
also equips a PIR (Passive infrared sensor) to sense movement of people and animals.
The PoE model built-in support for Power over Ethernet allows the camera to receive both
data and power over a single Ethernet cable.
This camera is an easy-to-use IP camera which is designed for security application.
2. Product Specifications
 Onvif compliance
 Mega-Pixel CMOS Sensor
 H.264 / MJPEG compression formats and triple streaming
 Supports resolution up to 1280x800, 720P@30FPS real time
 Self-Contained HTTP Web Server providing Internet capability for remote access
 Day & Night functionality for 24-hours surveillance, auto activate IR illuminator in low
illumination
 Infrared radiant distance up to 5 meters
 PIR (Passive infrared sensor) to sense movement of people, animals
 Digital Wide Dynamic Range
 Shutter Speed adjustment
 Sense Up adjustment
 3D+2D Digital Noise Reduction
 Day&Night Switch time control manually
 Wireless network connection (Wireless model)
 Built-in PoE splitter, support for Power over Ethernet (PoE model)
 Supports Micro-SD card for local event recording
 2-way audio
 Online firmware upgrade
3
 Free 36CH recording software
 Free App (iCAM Smart) for monitoring via Android/iOS smart phone
Hardware
CPU / RAM / ROM
Multimedia SoC / 256MB / 16MB
Image Sensor
1/4” Mega-Pixel CMOS
Lens
Fixed 2.8mm, Mega-Pixel Lens, F1.8
IR Distance
5 Meters
IR LED
Built-in 4 IR LEDs
Minimum Illumination
Color: 0.1 lux (when IR is off)
Day / Night
Built-in Mechanism IR Cut Filter (ICR)
Shutter Time
Auto: Indoor, Outdoor
Mono: 0 lux (when IR is on)
Manual: 1/30 ~ 1/1000 sec
Audio Input
Built-in microphone
Audio Output
Built-in speaker
3.5mm phone jack for connecting external amplified speaker
Digital In / Out
1 Digital in / 1 Digital out
Power Supply
Normal & Wireless model: DC 12V, 1.5A
PoE model (built-in PoE Splitter):
Use PoE: PoE Injector (IEEE 802.3af)
Or, use Power Adaptor: DC 12V, 1.5A
Power Consumption
Max. 5 Watt
Dimensions
W62 x H100 x D44 mm
Network
Ethernet
10/ 100 Base-T
Wireless (Wireless model)
802.11b/g/n, supports WPA-PSK, WPA2-PSK, WEP 64/ 128 bit
Network Protocol
IPv4/IPv6, HTTP, HTTPS, TCP/IP, RTP/RTSP, UDP, 3GPP, SMTP, FTP,
Samba, PPPoE, DHCP, DDNS, NTP, UPnP, SNMP, QoS/DSCP, IP Filter,
IEEE 802.1x, Bonjour
Onvif Compliance
Compliant with Onvif V2.20, 1.01
System
Video Resolution
1280x800, 1280x720, 640x480, 320x240, 176x144
Video Format
H.264 / MJPEG
Frame Rate
Up to 30FPS
Triple Streaming
2 for PC live view, 1 for mobile live view
3G Mobile View
Supports Android/ iOS devices, Live view with free APP – iCAM SMART
Video Bitrate Adjustment
CBR, VBR, up to 8Mbps
4
Video Adjustment
Brightness, Contrast, Hue, Saturation, Sharpness, Gain control, Shutter time,
Sense Up, Digital WDR, Anti Fog, Lens Distortion Correction, White Balance,
3D/2D Digital Noise Reduction, Day/Night color mode, Video orientation
Audio Format
G.711 (64Kbps), G.726 (24Kbps), G.726 (32Kbps)
Privacy Mask
3 definable areas
Security
Password protection, IP address filtering, HTTPS encrypted data
transmission, IEEE 802.1x port-based authentication, QoS/DSCP
Firmware Upgrade
HTTP mode, can be upgraded remotely
Event system
Event Trigger
Motion Detection, Digital In, Tampering Detection, PIR Detection
Triggered Action
Send Email, Send to FTP, Save to SD Card, Save to Samba HDD, Digital Out
Motion Area
3 definable areas
Pre / Post Alarm
Yes, configurable time
Micro-SD card management
Recording Trigger
Motion Detection, Digital In, Tampering Detection, PIR Detection, IP Check,
Network Disconnect
Schedule
Snapshot with schedule
Video Format
Video (AVI), Snapshot (JPEG)
Video Playback
Yes
Remote client access
Client Software
Microsoft IE V7.0 (32-bit) or above, Mozilla Firefox V6.0 or above, Opera
V11.5 or above, Safari V5.1 or above, Google Chrome V13.0 or above
Android / iOS smart phone: “iCAM Smart”
Connected Clients
Up to 10 clients simultaneously
PC Requirement
OS: Windows 7, Vista, XP
Suggested Hardware:
Intel Core 2 Duo 2.53GHz, RAM: 1GB
Graphic card: 128MB onboard
* Specifications are subject to change without notice
5
3. Product Installation
A. Hardware Installation
Cable Connections










 Network Connector:
The RJ-45 connector allows connect the Ethernet cable.
 Power Jack:
To connect the DC 12V power adapter.
 Speaker:
The built-in speaker to play the warning voice.
 Audio Output:
The 3.5mm phone jack allows connect to an amplified speaker,
you can hear the voice of the remote site from the speaker.
 Microphone:
The built-in microphone to receive the voice.
 Micro-SD Card Slot:
Insert a Micro-SD card if you want to do the event recording
(video only) in the camera.
 Focus Ring:
This ring allows adjust the focus.
6
 PIR Sensor:
PIR sensor to sense movement of people, animals.
 Digital I/O:
The terminal block provides the Digital In and Digital Out. The
pin assignments are:
(A) Digital Output (DO)
(B) Digital Input (DI)
(C) GND (G): Ground pin for both Digital Input and Digital
Output.
 Antenna Connector:
Available for Wireless model. To connect the included wireless
antenna.
1. Connect the cable of Digital I/O and Audio Output if you want to use these
functionalities.
2. Connect the wireless antenna for the Wireless camera.
3. Connect Ethernet cable for network connection.
4. Connect power adapter to turn on the camera.
5. If the camera is PoE model, the power adapter is not necessary. The camera will get
the power from the PoE injector or PoE switch.
PoE (Power over Ethernet) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as an IP
phone or a network camera, using the same cable as that used for network connection.
It eliminates the need for power outlets at the camera locations. Please follow the
below figure for the connection.
PoE Switch or PoE Injector
PoE Network Camera
To Network
Ethernet Cable
Data only
Ethernet Cable
Mixed data and power
6. Set up the network configurations according to the network environment. For further
explanation, please refer to Network Configuration chapter.
7. After finish the configuration for the very first time, if you want to use wireless network,
plug out the Ethernet cable.
7
I/O Connections
I/O terminal connector – used in application, for e.g., motion detection, event triggering,
alarm notifications. It provides the interface to:

1 set of Digital Input (Digital In + GND) – The digital inputs for connecting devices
that can toggle between an open and closed circuit, such as PIRs, door/window
contacts, glass break detectors, etc. When a signal is received the status changes
and the input becomes active.

1 set of Digital Output (Digital Out + GND) – The output to Relay Box or Relay
Board, and switch on the alarm device such as LEDs, Sirens, etc.
Digital IN
Digital OUT
Digital Input (Alarm Input)
GND (Ground): Initial status is LOW.
Alarm: Max. 50mA, 12VDC.
Door/Window
Contacts
8
Digital Output (Alarm Output)
Relay Board
or
Relay Box
9
B. Monitor Setting
1. Right-Click on the desktop. Select “Properties”
2. Change color quality to “Highest (32bit)”.
10
C. IP Assignment
 Always consult your network administrator before assigning an IP address to your
camera in order to avoid using a previously assigned IP address.
 MAC Address: Each network camera has a unique Ethernet address (MAC address)
shown on the sticker of the device.
 One final note, although the IP Search is able to find and configure any network
device on the LAN except those that are behind a router, it is a good idea to set the
host PC to the same subnet. In order to connect to the Web-based user interface of
the network camera, the host PC must be in the same subnet. For more information
about subnets, please consult your network administrator.
“Asoni IP Search” is a utility that provides an easier, more efficient way to configure the IP
address and network settings of the network camera in Local Network (LAN).
The software can be installed from the attached software CD.
1. Once “Asoni IP Search” has been successfully installed on the computer, double
click the “Search CAM4_CAM6_NVR6LX” icon on the desktop.




11

2. IP Search searches all the network devices which connect to the intranet and lists
on the window. Click [Search] button to search again.
3. From the list, click and select the device with the MAC Address that corresponds to
the device that is to be configured.
4. The network configuration of the selected device will show on the bottom, filling in
the Device Name, IP Address, Subnet Mask, Gateway and the others.
5. Click [Modify] button to save the settings into the device.
6. Wait for few seconds to let the device update the settings, and then click [Search]
button again to re-search the network devices.
7. Double-click the network device listed on the window, It will open an IE browser and
connect to this device directly.
12
4. Live Video
Start the IE browser, type the IP address of the
network camera in the address field:
http://<IP of camera>
If the “HTTP Port” has been changed from “80”,
type the URL as:
http://<IP of camera>:<HTTP Port>
After link to the camera, it will show a dialogue
box. Key-in the user name and password to
log-in and open the web page of camera.
The default user name and password are “admin” and “admin”.
For the first time links to camera by IE, it will ask you to install the ActiveX component,
please install this component.
If you are using IE 10, click “Compatibility View” icon to make this page works properly:
If you are using IE 11, click “Tool” icon (which is a gear wheel), and click “Compatibility
view settings”. In the dialog box, add the current IP address and then click “OK”, this web
page will be displayed properly.
The web page of the device shows as following.
13
⑤
①
②
③
④
⑥






Streaming : Select the streaming 1 or 2 from the pull-down list to display.
Language : Change the display language.
Configuration : Go into the configuration page to set the parameters if necessary.
Status Bar : Shows system date/time, video resolution and video refresh rate (FPS).
Online Visitor : Shows how many users connect to this network camera.
Function Buttons : Click these buttons will perform the following functions.
Full Screen : Click this button or double-click the video, the video will change
to full screen mode.
Press [Esc] key or double-click the video again, it will back to normal mode.
Snapshot : Click this button to take snapshot of the video. The image will be
displayed in a pop-up window, click
14
to save as a jpg picture.
Record : Click this button to record the video into the local PC. It will ask you
where to save the video. To stop recording, click this button again.
The saved video format is AVI. The recorded file can be played by Microsoft
Media Player. Note, H.264 decoder must be installed to play the recorded file.
You can install “FFdshow” from the included CD for the decoder.
Chatting : The camera supports 2-way audio. Click this button, then you can
use microphone which connected to the PC to talk to the camera side.
Voice : Click this button to turn on the audio from camera. Click again to turn
off it.
Digital Zoom : Click this
button, a pop-up window
appears. You can enable /
disable the digital zoom, and
adjust the ratio.
Relay Out (ON/OFF Switch) : Click the button to manually turn on / off the
Relay via the built-in Digital Out.
Relay Out (Time Switch) : Click the button to manually turn on the Relay via
the built-in Digital Out, after the interval time is passed, the Relay will be
turned off automatically. The interval time can be set up in Configuration 
Event Handling  I/O.
15
5. Configuration
Click [Configuration] button to get into the configuration page. Click
[Live View]
button to back to the Live-View page.
A. System
System Information
Set up the camera name, OSD (on screen display) information and the camera time.
System
Information
16
Server Information
MAC Address: The MAC address of the Ethernet network card in the device.
Server Name: You can type a name into this field to identify this device.
Show on Status Bar: Determine whether show the server name on the Status Bar.
LED Indicator: Determine whether light-on or turn-off the network and power status
LEDs on the device.
OSD Setting
Time Stamp: Enable this option will display the date and time on the video.
Position: Select the display position of Time stamp.
Text: Enable this option will display the OSD string on the video.
Text Edit: Click this button to open “Text
Edit” dialog window. You can change
the OSD string and adjust the
transparency of the text. After editing,
click [Apply] button.
17
Time Setting
Date Format: Select the format to display the date.
Time Zone: Select the GMT to match your time zone.
Enable Daylight Saving: If using “Daylight Saving”, enable this option and select the
start and end time.
Synchronize with NTP Server: Select this option and type the IP address of a NTP
(Network Time Protocol) server, this device will synchronize the time with the NTP
server via network.

NTP Server: Type the IP address or URL of the NTP server.

Update Schedule: Select the interval for the update time. For example, if
select “6 Hours”, this device will synchronize the date and time with the NTP
server every 6 hours.
Synchronize with PC’s time: Select this option will synchronize the device time with
the PC’s time.
Manually Input Date and Time: Manually input the date and time.
The date and time remain the same: Keep the current date and time without change.
18
After set up, click [Apply] to save the settings.
19
User Management
You can add, remove and manage the users in this page.
This device supports 3 user groups:
 Administrator: The administrator can view, operate and configure all functions and
settings of this device.
 Guest: The users in Guest group can only view the live video in Live-View page.
 Anonymous: The anonymous user can only view the live video in Live-View page.
The privilege is same as Guest group.
User
Management
Anonymous User Login
To allow user visit this device without login, select [Yes] and then click [Setting] to
enable this function.
Add User
To add a new user, type the user name and password, then click [Add/Set] to save
the user.
User List
This table lists the current users.
20
Edit: To change the username and
password, click [Edit] and modify the
administrator or user in the pop-up window.
Remove: To remove the user, click [Remove].
21
System Upgrade
This page allows user to upgrade firmware, restart device and restore the factory default
settings.
System
Upgrade
Firmware Upgrade
The firmware can be upgraded online.
To update the firmware, click [Browse…] to select the new firmware file, and then
click [Upgrade] to the procedure.
Reboot System
To restart the device, click [Reboot] and then click [Yes] on the prompted window.
Factory Default
To load the factory defaults, click [Default] and then click [Yes] on the prompted
window. Note, all settings including User account, Network, A/V and Event settings
will be restored to the factory defaults.
22
System Logs
System Logs
System Status Logs
Click the [View] button on the right side to list the logs of system status.
Motion Trigger Logs
Click the [View] button on the right side to list the logs of motion detection.
Digital-In Trigger Logs
Click the [View] button on the right side to list the logs of digital input detection.
All Logs
Click the [View] button on the right side to list all logs.
23
B. Video/Audio Setting
Video Format
This device supports H.264 and MJPEG Dual Mode and Triple Streaming, set the video
parameters in this page.
Video Format
24
Video System
Select NTSC-60Hz or PAL-50Hz to match your local video system.
Streaming 1 Output Setting
Basic / Advanced Mode: Select the mode to configure the parameters. Advanced
mode provides more detail parameters for setting.
Resolution: Select the resolution from the pull-down list.

1280x800 (Up to 30FPS)

1280x720 (Up to 30FPS)

640X480 (Up to 30FPS)

320X240 (Up to 30FPS)

176X144 (Up to 30FPS)
Frame Rate Per Second: The video refreshing rate per second. Select the frame rate
from the pull-down list.
Video Compression Format: Choose H.264 or MJPEG format to compress and
output the video stream.
H.264: The video stream will be compressed in H.264 format.

Profile: Provides “Baseline” and “Main” profile. “Main” profile can deliver
better video quality, but it will cause network camera have larger load
relatively.

CBR (Constant Bit Rate): Set the Video Bitrate from 32Kbps ~ 8Mbps
depend on the upload bandwidth of network. The data size of video
stream will be limited under the selected bit rate.
25

VBR (Variable Bit Rate): Set the Video Quantitative from 1 ~ 10, the
higher value will get better video quality. The data size of video stream is
no limitation, if the upload bandwidth of network is lower than the data
size, the video will be displayed slowly.

GOP Size: Set the GOP (Group of Picture) size. If you don’t know what
value should be set, please set it to “1XFPS”.
MJPEG: The video stream will be compressed in MJPEG format.

Quality: 5 levels for select. The higher quality will get bigger file size.
RTSP Path: Assign a name to identify this video stream. When view the video stream
with RTSP connection, the URL should be “rtsp://<Public IP of this device>:<RTSP
port>/<RTSP path>”.
Streaming 2 Output Setting
Basic / Advanced / Close Mode: Select the mode to configure the parameters.
Advanced mode provides more detail parameters for setting. Select Close mode will
disable the streaming 2.
Resolution: Select the resolution from the pull-down list.

1280x800 (Up to 30FPS)

1280x720 (Up to 30FPS)

640X480 (Up to 30FPS)

320X240 (Up to 30FPS)

176X144 (Up to 30FPS)
26
Frame Rate Per Second: The video refreshing rate per second. Select the frame rate
from the pull-down list.
Video Compression Format: Choose H.264 or MJPEG format to compress and
output the video stream.
H.264: The video stream will be compressed in H.264 format.

Profile: Provides “Baseline” and “Main” profile. “Main” profile can deliver
better video quality, but it will cause network camera have larger load
relatively.

CBR (Constant Bit Rate): Set the Video Bitrate from 32Kbps ~ 8Mbps
depend on the upload bandwidth of network. The data size of video
stream will be limited under the selected bit rate.

VBR (Variable Bit Rate): Set the Video Quantitative from 1 ~ 10, the
higher value will get better video quality. The data size of video stream is
no limitation, if the upload bandwidth of network is lower than the data
size, the video will be displayed slowly.

GOP Size: Set the GOP (Group of Picture) size. If you don’t know what
value should be set, please set it to “1XFPS”.
MJPEG: The video stream will be compressed in MJPEG format.

Quality: 5 levels for select. The higher quality will get bigger file size.
RTSP Path: Assign a name to identify this video stream. When view the video stream
with RTSP connection, the URL should be “rtsp://<Public IP of this device>:<RTSP
port>/<RTSP path>”.
3GPP Streaming Output Setting
After enable the 3GPP streaming, it will enable this device to send out the video in
3GPP format, and you can view the live video on the 3G mobile phone.
Resolution: Select the resolution from the pull-down list.
27

640X480 (Up to 15FPS)

320X240 (Up to 15FPS)

176X144 (Up to 15FPS)
Frame Rate Per Second: The video refreshing rate per second. Select the frame rate
from the pull-down list.
CBR: Set the Video Bitrate from 32Kbps ~ 1Mbps depend on the upload bandwidth of
network. The data size of video stream will be limited under the selected bit rate.
RTSP Path: Assign a name to identify this video stream. When view the video stream
with RTSP connection, the URL should be “rtsp://<Public IP of this device>:<RTSP
port>/<RTSP path>”.
View Live Video with iPhone and iPad
To view the live video with a iOS mobile device (iPhone or iPad), open “Safari” web
browser in the mobile phone, type the URL as following to link and view the live video:
http://<Public IP of camera>:<HTTP port>
* <Public IP of camera>: The public IP address of the camera.
* <HTTP port>: The HTTP port of the camera. This port is assigned in Configuration
 Network Setting  Network Setting
View Live Video with Android Device
To view the live video with a 3G mobile phone or PDA (including Android devices),
open “Streaming Player” or web browser in the mobile phone, type the URL as
following to link and view the live video:
rtsp://<Public IP of camera>:<RTSP port>/<RTSP path of 3GPP Streaming>
* <Public IP of camera>: The public IP address of the camera.
* <RTSP port>: The RTSP port of the camera. This port is assigned in Configuration
 Network Setting  Network Setting
* < RTSP path of 3GPP Streaming >: The name of the 3GPP video stream.
If your 3G mobile phone or PDA does not support the viewing of RTSP streaming, you
can view the camera with http connection. To do this, use a Java compliant browser
such as Opera, and type the URL as following to link and view the live video:
http://<Public IP of camera>:<HTTP port>/Jview.html
28
* <Public IP of camera>: The public IP address of the camera.
* <HTTP port>: The HTTP port of the camera. This port is assigned in Configuration
 Network Setting  Network Setting
Note: Do not use the IE browser in 3G mobile phone because it doesn’t support Java.
After set up, click [Apply] to save the settings.
29
Image Setting
Image Setting
30
Privacy Mask
For the security purpose, there are 3 areas can be setup for privacy masks, the
masked areas will not be shown in Live-View and recorded file. To set up or clear the
privacy mask, click [Draw/Clear Area] button, and then use mouse to drag the area
on the video. After configuration, click [Save Area Settings] button to save the
settings.
Image Quality
Brightness / Contrast / Hue / Saturation / Sharpness: Adjust these parameters to
get clear video.
Automatic Gain Control: Adjust this function according to the environment.
Shutter Time:

Outdoor / Indoor: Select one of these two options according to the
environment, the camera will adjust the shutter time automatically.

1/30 ~ 1/1000: Manually adjust and fix the shutter time for different
application.
Sense-Up: Adjust this parameter depend on the environment to get clear video.
Digital-WDR: This camera supports “Digital Wide Dynamic Range”, provides clear
images when there are both very bright and very dark areas simultaneously in the
field of view of the camera. Adjust this parameter depend on the environment.
Anti Fog: After enable this function, it will display a clearer image in fog environment.
Lens Distortion Correction: This function will correct the distortion of the image.
Video Orientation: Change the orientation to display the video.
White Balance Adjust - Red Gain: Adjust the gain level of red color for the automatic
white balance.
White Balance Adjust - Blue Gain: Adjust the gain level of blue color for the
automatic white balance.
Denoise: This camera supports 3D and 2D “Digital Noise Reduction”, adjust this
parameter to get clear video.
Default: Click [Default] button will load the default settings.
Day/Night Color Mode (ICR)
If the camera equips ICR (IR Cut Filter), you can configure this function to determine
31
when to switch on/ off the ICR.
Auto (by Defined-Lux):
You can define the Lux of environment to change the color mode automatically.
When the environment is brighter than “Color – when over”, the video will display
in color; when the environment is darker than “Mono – when under”, the video will
display in mono color (black and white).
You can click [Refresh] button to detect the current Lux of environment.
Always Color:
The video will always display in color.
Always Mono:
The video will always display in mono color (black and white).
Auto (by Defined-Time):
You can define the period to change the color mode automatically. To set the time,
type the time in “Color - start from” and “Mono - start from” fields, and then click
[Save Time Settings] to save the configuration.
Synchronize with Digital-Input-1:
The ICR will be synchronized with Digital-Input-1, and the Digital-Input-1 cannot
be used by user for other purpose. This option is for specific camera model,
please do not select this option with this camera.
32
Audio Setting
This device supports 2-way audio. Note, the audio will not be smooth when enable SD
card recording function simultaneously.
Audio Setting
Audio from Device to Local PC
For this device to local PC, select [Enable] and then click [Apply] to start this function.
If set to [Disable], the [Voice] icon on Live View page is not workable.
You can also change the Audio Type if necessary.
Audio from Local PC to This Device
For local PC to this device, click [Chatting] icon on the Live View page and then talk
to the microphone connected on PC.
33
Adjust Volume
The volume level of Microphone-In and Audio-Out can be adjusted.
34
C. Network Setting
Network Setting
Network
Setting
35
IP Assignment
DHCP: If this device behinds a router and the router provides DHCP service, using
DHCP, this device will get all network parameters from the router automatically.
Static: Assign IP address, subnet mask, gateway, and DNS manually.
IPv6 Assignment
This device supports IPv6 address, you can enable this function.
Manually Setup the IPv6 Address: Assign IP address, gateway, and DNS manually.
IPv6 DHCP: If this device behinds a router and the router provides DHCP service for
IPv6, enable DHCP, this device will get all network parameters from the router
automatically.
Port Assignment
Set the port if necessary. If this device will be connected via Internet, configure the
NAT (Network Address Translation) in router to match the port assignment.
HTTP Port: Set the port for HTTP connection. The default is “80”, change the port if
you want to use router’s NAT (Network Address Translation) to make this device can
36
be linked from Internet.
HTTPS Port: Set the port for HTTPS connection. The default is “443”, change the port
if you want to use router’s NAT (Network Address Translation) to make this device can
be linked from Internet.
UPnP Setting
UPnP: Enable or disable the UPnP protocol.
This device supports UPnP, if the UPnP service is enabled on your computer, the
device will automatically be detected and a new icon will be added to “My Network
Places”.
Note: UPnP service must be enabled on your computer.
The Windows Vista and Windows 7 have enabled UPnP service by default. To activate
UPnP service in Windows XP, please follow the procedure:
1. Open the “Control Panel” from the “Start” menu.
2. Select “Add/Remove Programs”.
3. Select “Add/Remove Windows Components” and open “Networking Services”
section.
4. Click “Details” and select “UPnP” to setup the service.
5. The network device icon will be added to “My Network Places”.
6. You may double-click the network device icon to access it via IE browser.
UPnP Port Forwarding: Enable or disable the “UPnP Port Forwarding” function.
The “UPnP Port Forwarding” function provides an easy way to configure the NAT
(Network Address Translation) in router. If the router equips “UPnP Port Forwarding”
function too, this device will ask the router to open the “External HTTP Port”, “External
HTTPS Port” and “External RTSP Port” for this device automatically. Therefore, you
don’t need to configure the Port Forwarding manually.
Note: Not all routers equip “UPnP Port Forwarding” function. The device will report
whether this function is successful after click [Apply] button.
37
RTSP Server Setting
RTSP Server: The video stream can be direct retrieve via RTSP connection, you can
close this function by disable this option.
RTSP Authentication: If you select and enable this function, the remote client must
meet the authentication to retrieve video stream via RTSP connection.
RTSP Port: Set the port for transfer the video and audio. The default is “554”, change
the port if you want to use router’s NAT (Network Address Translation) to make this
device can be linked from Internet.
RTP Port: Set the port range of RTP port.
In RTSP mode, you may use TCP and UDP for connecting. TCP connection uses
RTSP Port. UDP connection uses RTP Start and End Port.
Multicast Setting (Based on the RTSP Server)
Multicast addressing is a network technology for the delivery of streaming to a group
of destinations simultaneously using the most efficient strategy to deliver the
messages over each link of the network only once, creating copies only when the links
to the multiple destinations split. To implement the Multicast, a switch or router that
supports Multicast function is necessary in the network.
If your network supports Multicast, you can configure the device to enable this
function by setup the following:
IP Address: This is the multicast group address the streaming should be sent to. You
38
should configure each recipient with the same multicast group address and receive
the streaming from this address. The range is 224.3.1.0 ~ 239.255.255.255
Port: The multicast port. The range is 1 ~ 65535
TTL: Time-To-Live (TTL) for Multicast Packets. This value decides how "far" from a
sending host a given multicast packet should be forwarded.
Onvif Setting
This device supports Onvif standard, you can configure the following settings to
compatible with the NVC (Network Video Client) such as NVR or recording software:
Onvif Version: Select the version of Onvif standard, or disable the Onvif output.
Security: Enable or disable the Onvif security authentication.
RTSP Keepalive: If select “Enable”, when the NVC doesn’t send the command for
keeping the RTSP connection, this device will terminate the RTSP connection. If
select “Disable”, this device will always keep the RTSP connection. If the “Time-out”
error happens on NVC side, please disable this function.
Bonjour and LLTD Setting
This device supports Bonjour and LLTD function, you can configure the settings.
After set up, click [Apply] to save the settings.
39
Wireless Setting
The Wireless model supports Wireless network connection, set the parameters in this
page.
Note: Wireless network and Ethernet network use the same IP, user has to unplug
Ethernet cable to activate the Wireless connection. If Ethernet cable is plugged,
Wireless connection will be stopped.
Wireless
Found Wireless Networks
The Wireless model will automatic search the available Wireless network and list in
the SSID table. Please refer to the table to set the Wireless settings.
Wireless Setting
Mode: Select the mode of the connection from the pull-down list. “Infrastructure” is for
connecting with the router. “Ad-hoc” is for connecting with PC directly.
Operation Mode: Select the mode from the pull-down list.
SSID: Choose a Wireless network from the SSID table, and type the SSID in the box.
The SSID is case-sensitive.
Security: Select the security mode to match the Wireless network. It supports “None”,
“WEP”, “WPA-PSK”, “WPA2-PSK” security encryption based on the setting of Router.
Ad-hoc
Ad-hoc is for connecting with PC directly. There is “Channel” to selected only when
uses Ad-hoc mode. For example, if PC’s channel is 6, the “Channel” has to be 6 too.
40
WEP Setting
The Wireless model supports “WEP” security encryption. The settings must be same
as the Router’s setting. Consult your network administrator to set the parameters.
41
Authentication: There are “Open System” and “Shared Keys”, it is based on different
encryptions. This has to be the same as the Router’s setting.
Encryption: There are 64 bits and 128 bits. This is based on Key Type based on the
Router’s setting.
Key Type: There are HEX and ASCII. When selecting HEX, the user only can input
0~9 characters and use A, B, C, D, E, and F. When selecting ASCII, the user can input
any character (case [upper cases/ lower cases] sensitive).
Key 1~4: Based on Key Type to input characters.
WPA-PSK Setting
The Wireless model supports “WPA-PSK” and “WPA2-PSK” security encryption. The
settings must be same as the Router’s setting. Consult your network administrator to
set the parameters.
Encryption: There are “TKIP” and “AES”.
Pre-Shared Key: Allow any characters (case [upper cases/ lower cases] sensitive).
After set up, click [Apply] to save the settings.
42
Mail / FTP / Samba Setting
To send out the event video to E-mail, FTP or Samba network storage, please set up the
configuration first.
Mail/FTP/Samba
43
Mail Setting
Login Method: This device provides 2 kinds of mail settings. “Anonymous” for the
mail server which doesn’t need login with user name and password. “Account” for the
mail server which needs login with user name and password.
Send Mail Server: The IP address or URL of the send-mail server.
User Name / Password: The user name and password of the sender to login mail
server and send the mail.
Sender’s Mail: The sender’s mail address.
Receiver’s Mail: The receiver’s mail address.
BCC Mail: The mail address to receive the mail also.
Mail Port: The port of the mail service. Default is 25.
Secure Connect: Enable this function if your mail server needs it.
FTP Setting
44
FTP Server: The IP address or URL of the FTP server.
User Name / Password: The user name and password to log in the FTP server.
FTP Port: The port of the FTP service. Default is 21.
Store Path: The path to save the sent video file.
FTP Mode: Select “PORT” or “PASV to fit the FTP server. “PORT” is for sending file to
an Active FTP server; “PASV” is for sending file to a Passive FTP server.
Auto Create Folder by Date: If select “Yes”, a folder will be created under the “Store
Path” and named with the date, and then the video file will be saved in this folder. If
select “No”, the video file will be saved in the “Store Path” without folder.
Samba (Network Storage) Setting
“Samba” is a networking protocol provides file sharing service between network
devices. If you have a network storage is running Samba service, this camera can
send the event video or snapshot to the network storage directly.
NAS Location: The location of the Samba network storage, including IP address or
URL and the folder, the event video or snapshot will be send to this location.
Workgroup: Type the work group this Samba network storage belong to.
User Name / Password: The user name and password to log in the Samba network
storage.
Auto Create Folder by Date: If select “Yes”, a folder will be created under the “NAS
Location” and named with the date, and then the video file will be saved in this folder.
If select “No”, the video file will be saved in the “NAS Location” without folder.
After set up, click [Apply] to save the settings.
Test the Settings
You can click [Test] button, this device will send a test mail to receiver’s mail box, or
upload a test file to FTP site and the Samba network storage, to make sure the
45
settings of mail, FTP or Samba network storage are correct.
46
PPPoE / DDNS Setting
PPPoE/DDNS
Setting
PPPoE Setting
If this device connects to an ADSL modem directly and want to use PPPoE
connection, select [Enable] and then set the parameters in this page.
47
Enable/ Disable: Enable or disable the PPPoE connection.
User name/ Password: Input the user name and password of the PPPoE connection.
Send E-mail After Dialed: If select [Enable], when connect to the Internet via PPPoE,
this device will send a mail with the Subject to a specific mail account, this mail
contains the public IP address of the ADSL connection. To set the mail account,
please refer to Configuration  Network Setting  Mail/FTP/Samba page.
E-mail Subject: The subject of the E-mail will be sent.
DDNS Setting
This device supports DDNS, set the parameters in this page.
48
There are several DDNS providers can be selected. Select the provider from the
pull-down list, input Hostname, User name, Password and the Schedule Update time,
and then click [Apply] to connect to the DDNS provider.
After set up, click [Apply] to save the settings.
The “Status” field will display the message to indicate the status of DDNS service.
Updating: Information update.
Idle: Stop service.
http://<hostname (username)>.<provider>.com: DDNS registration successful, can
now link to the camera with this URL address.
Update Failed, the name is already registered: The hostname or username has already
been used. Please change it.
Update Failed, check your internet connection: Network connection failed.
Update Failed, please check the account information with you provider: The input
hostname, username or password may be wrong.
49
D. Network (Advance) Setting
HTTPS Setting
HTTPS (Hypertext Transfer Protocol Secure) is a combination of Hypertext Transfer
Protocol (HTTP) with SSL/TLS protocol. It provides encrypted communication and secure
identification of a network web server. Https can help protect streaming data transmission
over the network on the higher security level.
HTTPS
Setting
Before setting new request, please remove old secure identification at Http connection
type.
50
Created Request
Input the secure identification and then click [Apply] to save the settings.
Install Certificate
There are two ways to set Certificate – “Install Signed Certificate” and “Create
Self-Signed Certificate”.
Input the necessary data and then click [Apply] to save the settings.
51
SNMP Setting
SNMP (Simple Network Management Protocol) is an Internet-standard protocol for
managing devices on IP networks. It is used mostly in network management systems to
monitor network-attached devices for conditions that warrant administrative attention.
SNMP exposes management data in the form of variables on the managed systems,
which describe the system configuration.
SNMP Setting
SNMPv1 and SNMPv2
To use SNMPv1 or SNMPv2, click the checkbox to enable SNMPv1 or SNMPv2, and
then input the name of Write Community and Read Community.
52
SNMPv3
To use SNMPv3, click the checkbox to enable SNMPv3, and then set Security Name,
Authentication Type, Authentication Password, Encryption Type, Encryption
Password of Write mode and Read mode.
SNMPv1/ v2c Trap
Enable “SNMPv1/ v2c Trap” can detect the Trap server. Please click the checkbox to
select what event need to be detected.
After set up, click [Apply] to save the settings.
53
IP Filter Setting
The IP Filter function allows you to create the IP address list to manage the clients that are
allowed or denied to access this device.
IP Filter
Setting
IP Address Filter Setting
Enable IP address filter: Click the checkbox to enable this function.
IPv4 IP Address: Input the IP address (single or range) that will be allowed or denied
to access this device. After input the IP address, click [Add] to save it, the IP address
will be listed in “IPv4 IP Address List”.
IPv4 IP Address List: Here lists the Allow/ Deny IP addresses. To remove the IP
address from the list, just click [Remove] button on the right.
54
Administrator Access
To always allow the administrator access this device, click the checkbox to enable this
function, and the input the IP address of administrator.
After set up, click [Apply] to save the settings.
55
QoS/ DSCP Setting
DSCP (Differentiated Services Code point) specifies a simple mechanism for classifying
and managing network traffic and provide QoS (Quality of Service) on IP networks. DSCP
is a 6-bit in the IP header for packet classification purpose. Please define the reserve for
Live Stream, Event/ Alarm and Management.
QoS/ DSCP
Setting
After set up, click [Apply] to save the settings.
56
IEEE 802.1x Setting
IEEE 802.1x is an IEEE standard for port-based Network Access Control. It provides an
authentication mechanism to device wishing to attach to a LAN or WLAN.
The EAPOL protocol support service identification and optional point to point encryption
over the local LAN segment.
IEEE802.1x
Setting
Please check what version of the authenticator and authentication server support. This
device supports EAP-TLS method. Please enter ID, password issued by the CA, and then
click [Apply] to save the settings.
Then, upload the related certificates.
57
E. Event Handling
Event Setting
This device supports multiple event settings.
Event
This device supports 6 kinds of event detections:
 Motion Detection.
58
 Digital Input Detection.
 Tampering Detection: This event will be triggered when the lens of camera has
been covered or moved.
 Network Disconnection Detection: This event will be triggered once the wire
network is disconnected.
 Specific IP Detection: This event will be triggered once the network connection
with a specific IP address is disconnected.
 PIR Detection: This event will be triggered once the camera detects the
movement of people or animals.
Motion Detection
This device allows 3 areas for detect motion. When motion detection is triggered, it
can send the video or snapshot to specific mail address; transmit the video or
snapshot to remote FTP server or Samba network storage; trigger the digital out;
record video or snapshot into local SD card.
59
Set the Area: To set up or clear the motion area, click [Draw/Clear Area] button on
“Set Area” row, and then use mouse to drag the area on the video.
Adjust the Sensitivity: To adjust the sensitivity of detection, select the level from the
pull-down list.
Activate Motion Detection: To activate the motion detection, enable the [Detect
Area] check box
Actions when Motion Detection is Trigger: Select what actions will be taken once
the motion detection is triggered in each area.

E-mail: When the motion detection is triggered in this area, send the recorded
video or snapshot to the specific mail address.

FTP: When the motion detection is triggered in this area, send the recorded
video or snapshot to the specific FTP site.

Save to Samba: When the motion detection is triggered in this area, send the
recorded video or snapshot to the Samba network storage.
To set the mail account FTP site and Samba network storage, please refer to
Configuration  Network Setting  Mail/FTP/Samba page.

Out1: When the motion detection is triggered in this area, turn on the Digital
Output 1.

Save to SD Card: When the motion detection is triggered in this area, record
the video or snapshot into the local SD card.
Log: If “Save to SD Card” option has been selected for action, you can determine
whether send a message to the specific mail address FTP site or Samba network
storage.
E-Mail Subject: The subject of the E-mail will be sent.
Detection Interval: This option provides two functions:

The interval time between multiple detections. For example, if the time set to
10 seconds, when the motion detection is triggered at time 10H:05M:10S, the
next detection will be accepted after 10H:05M:20S. The detections between
10H:05M:10S to 10H:05M:19S will not be accepted.

If the “Out” is selected for the action, the Interval means “Digital Output On”
period. For example, if Interval set to 20 seconds, when the motion detection
is triggered, the Digital Output will be “On” and lasting for 20 seconds, and
then “Off” automatically.
Enable Motion Detection in Schedule Time: Enable this option will automatic
activate the motion detection with scheduled time and stop the detection in the other
60
time. Please refer to Schedule page to setup the schedule time.
Recommendation of Motion Detection Area
To ensure the Motion Detection works well, and avoid unnecessary trigger, please
follow the rules to draw the Motion Detection Areas:
 The moving object larger than the 50% of the Motion Detection Area, it will be
detected, and the Motion Detection is triggered.
 The moving object smaller than the 50% of the Motion Detection Area, it will not
be detected, and the Motion Detection will not be triggered.
 Recommend use 3 smaller Motion Detection Areas to replace a large area.
Motion!
The moving object smaller than the 50% of the
The moving object larger than the 50% of the motion
motion area, it will not be detected!
area, it will be detected, and the motion is triggered!
To detect the smaller moving object, use 3 motion areas to replace a large motion
area, refer the figure below:
Motion!
The moving object will be detected when it is in any of
the 3 motion areas, and the motion is triggered!
Tampering Detection
This device provides the “Tampering Detection” function.
61
Tampering Detection – Enable / Disable: Select to enable or disable this function.
After enable the “Tampering Detection”, when the lens of camera has been covered or
moved, this event will be triggered, and send the video or snapshot to specific mail
address; transmit the video or snapshot to remote FTP server or Samba network
storage; trigger the digital out; record video or snapshot into local SD card.
When Detected: Select what actions will be taken once the tampering detection is
triggered.

E-mail: When the tampering detection is triggered, send the recorded video
or snapshot to the specific mail address.

FTP: When the tampering detection is triggered, send the recorded video or
snapshot to the specific FTP site.

Save to Samba: When the tampering detection is triggered, send the
recorded video or snapshot to the Samba network storage.
To set the mail account, FTP site and Samba network storage, please refer to
Configuration  Network Setting  Mail/FTP/Samba page.

Out1: When the tampering detection is triggered, turn on the Digital Output 1.

Save to SD Card: When the tampering detection is triggered, record the
video or snapshot into the local SD card.
Detection Interval: The interval time of the detection. When the lens of camera has
been covered or moved longer than the selected time, the event will be triggered.
Record File Setting
There are 3 methods to record the event video in SD card or send out via E-mail, FTP:
Video: When an event is triggered, the video will be recorded as still image with AVI
format. The beginning and ending time of the file is depending on the Pre and Post
62
Record Time Setting.
Snapshots: This option is available when the “Video Format” of streaming 1 is set as
“MJPEG” in Video Format. When an event is triggered, this device will take a series of
snapshot with JPG format. The beginning and ending time of the snapshot pictures is
depending on the Pre and Post Record Time Setting.
Snapshot (Single): This option is available when the “Video Format” of streaming 1 is
set as “MJPEG” in Video Format page. When an event is triggered, this device will
take a snapshot with JPG format.
Pre and Post Record Time Setting
Configure the record time for the event recording file. For example, if set “Pre Alarm”
as 3 seconds and set “Post Alarm” as 5 seconds, when an event is triggered at time
10H:05M:10S, the video will be recorded from 10H:05M:07S to 10H:05M:14S.
Note: Limited by the built-in RAM of this device, when data is too much or video
quality set too high, it will cause recording frame drop or decrease the recording
time of post alarm.
To avoid the “frame drop” situation, please reduce the bitrate of the video. We
recommend connect the device in LAN (Local Network) and set the video as
CBR, and Bitrate less than 1.5Mbps.
Network Disconnection Detect
After enable the check box of “Record Video into SD Card”, when the wire network is
disconnected, it will save the video into local SD card.
Note: When this event is happen, the frame rate of live video and recorded video will
be limited to 5FPS. The longest continue record period of single video file is 20
minutes, and the interval of two video files is fixed with 1 minute.
Specific IP Detection
For the use of recording software, this device supports the detection of the connection
of this device and PC. Whenever the connection is disconnected, it records the video
to local SD card to make sure the video recording is continuous.
63
Detect IP – Enable / Disable: Select to enable or disable this function.
IP Address: The IP address or URL of the PC which installed the recording software.
Detection Interval: The interval time of the detection.
When Dis-connected: After enable the check box of “Record Video into SD Card”,
when the network connection of PC is disconnected, it will save the video into local
SD card.
Note: When this event is happen, the frame rate of live video and recorded video will
be limited to 5FPS. The longest continue record period of single video file is 20
minutes, and the interval of two video files is fixed with 1 minute.
PIR Detection
This device equips a PIR (Passive infrared sensor), when the PIR detects the
movement of people or animals, it can send the video or snapshot to specific mail
address; transmit the video or snapshot to remote FTP server or Samba network
storage; trigger the digital out; record video or snapshot into local SD card, or warning
with audio.
PIR Detection: Click the checkbox to enable or disable this function.
Actions when PIR Detection is Trigger: Select what actions will be taken once the
PIR detection is triggered.

E-mail: When the PIR detection is triggered, send the recorded video or
64
snapshot to the specific mail address.

FTP: When the PIR detection is triggered, send the recorded video or
snapshot to the specific FTP site.

Save to Samba: When the PIR detection is triggered, send the recorded
video or snapshot to the Samba network storage.
To set the mail account FTP site and Samba network storage, please refer to
Configuration  Network Setting  Mail/FTP/Samba page.

Out1: When the PIR detection is triggered, turn on the Digital Output 1.

Save to SD Card: When the PIR detection is triggered, record the video or
snapshot into the local SD card.

Audio Out: When the PIR detection is triggered, warning with audio.
Audio File (.wav): Select the warning audio from the pull-down list. You can click
[Test] button to hear the audio.
Detection Interval: The interval time of the detection.
Note: When this event is happen, the frame rate of live video and recorded video will
be limited to 5FPS. The longest continue record period of single video file is 20
minutes, and the interval of two video files is fixed with 1 minute.
Upload Audio File (.wav): Select the warning audio from the pull-down list. You can
then select the audio from the pull-down list of “Audio File (.wav)” field.
Record Audio: You can record a period (around 5 seconds) of voice to be the
warning audio. Just click [Record] button and speak to the built-in microphone of
camera, and then select the audio from the pull-down list of “Audio File (.wav)” field.
After set up, click [Apply] to save the settings.
65
I/O Setting
This device provides Digital Input and Digital Output. When the Digital Input is triggered, it
can send the video or snapshot to specific mail address; transmit the video or snapshot to
remote FTP server or Samba network storage; trigger the digital out; record video or
snapshot into local SD card.
I/O Setting
Digital Input Setting
Input 1 Sensor Type: Select the type of the sensor which connected to the Digital
Input. [N.O] means “Normally Opened”, this type of sensor will be triggered when it is
closed. [N.C] means “Normally Closed”, this type of sensor will be triggered when it is
opened.
Input 1 Trigger Action: Select the actions when the Digital Input is triggered.

E-mail: When the Digital Input is triggered, send the recorded video or
snapshot to the specific mail address.

FTP: When the Digital Input is triggered, send the recorded video or snapshot
to the specific FTP site.

Save to Samba: When the Digital Input is triggered, send the recorded video
or snapshot to the Samba network storage.
To set the mail account FTP site and Samba network storage, please refer to
Configuration  Network Setting  Mail/FTP/Samba page.

Out1: When the Digital Input is triggered, activate the Digital Output 1.
66

Save to SD Card: When the Digital Input is triggered, record the video or
snapshot into to SD card.
Log: If “Save to SD Card” option has been selected for action, you can determine
whether send a message to the specific mail address FTP site or Samba network
storage.
E-Mail Subject: The subject of the E-mail will be sent.
Detection Interval: This option provides two functions.

The interval time between multiple detections. For example, if the time set to
10 seconds, when the Digital Input is triggered at time 10H:05M:10S, the next
trigger will be accepted after 10H:05M:20S. The triggers between
10H:05M:10S to 10H:05M:19S will not be accepted.

If the “Out” is selected for the action, the Interval means “Digital Output On”
period. For example, if Interval set to 20 seconds, when the Digital Input is
triggered, the Digital Output will be “On” and lasting for 20 seconds, and then
“Off” automatically.
Enable Digital Input Detection in Schedule Time: Enable this option will automatic
activate the Digital-Input detection with scheduled time and stop the detection in the
other time. Please refer to Schedule page to setup the schedule time.
Digital Output Setting
This section is for setup the parameters of Digital Output.
Note: The following settings are available when manually turn on the Relay Out on
Live-View page.
Output Switch Type: Select the type of the Digital Output switch. [On/Off Switch]
will be triggered to On or Off constantly. [Time Switch] will be triggered to “On” and
lasting for a period time, and then “Off” automatically.
Turn-On Time: If the Digital Output switch is a “Time Switch”, the lasting time of the
“On” period can be set here.
After set up, click [Apply] to save the settings.
67
Schedule
This function provides the schedule for the following:
 Send Snapshot with the Scheduled Time: automatic send a snapshot to the E-mail
address, FTP server or Samba network storage, or save to SD card. The interval
time can be set.
 Activate and Stop the Motion Detection with Scheduled Time: if the “Enable
Motion Detection in Schedule Time” option in Configuration  Event Handling 
Event Setting  Motion Detection page is enabled, the motion detection will be
activated with scheduled time and stop the detection in the other time.
 Activate and Stop the Digital Input Detection with Scheduled Time: if the “Enable
Digital Input Detection in Schedule Time” option in Configuration  Event
Handling  I/O Setting page is enabled, the Digital-Input detection will be
activated with scheduled time and stop the detection in the other time.
Schedule
Setup Schedule
Select / Unselect All Time: Click [All] of the top-left of the time table to select or
68
unselect all time. The square in green means the time is selected; the square in
light-grey means the time is unselected.
Select / Unselect Specific Time: Click the square of the time table to select or
unselect the specific time. The square in green means the time is selected; the square
in light-grey means the time is unselected.
Send Snapshot with Scheduled Time
Enable / Disable: To enable or disable the schedule function.
Snapshot: Select the method to send out the snapshot.

E-mail: Automatic send the snapshot to the specific mail address, the interval
time of the snapshot pictures is depending on the Interval setting.

FTP: Automatic send the snapshot to the specific FTP site, the interval time
of the snapshot pictures is depending on the Interval setting.

Save to Samba: Automatic send the snapshot to the Samba network storage,
the interval time of the snapshot pictures is depending on the Interval setting.
To set the mail account FTP site and Samba network storage, please refer to
Configuration  Network Setting  Mail/FTP/Samba page.

Save to SD Card: Automatic save the snapshot into SD card, the interval time
of the snapshot pictures is depending on the Interval setting.
Interval: The interval time of the snapshot pictures. For example, if the time set to 10
seconds, in the scheduled time, the device will send out snapshot every 10 seconds.
File Name: The header of the filename of the snapshot. For example, if you input
“Camera” in this field, the filename of the snapshot will be
“Camera-yyyymmdd-hhmmss.jpg”, “yyyymmdd” indicates the year, month and date;
hhmmss indicates the hour, minute and second.
After set up, click [Apply] to save the settings.
69
Micro-SD Card
In this page, if a Micro-SD Card is inserted, you can record the video once an event is
triggered, play back and manage the recorded files in the Micro-SD Card.
Note: The Micro-SD card must be formatted as FAT or FAT32 file system.
The use of the Micro-SD Card will affect the operation of this device slightly, such as
affecting the frame rate of the video.
Install Micro-SD Card
Make sure the direction and pushing Micro-SD card into the slot completely.
Record
Enable [Save to SD Card] option in Event Setting or I/O Setting page, the video can
be recorded into the card once the event is triggered. When the Micro-SD Card is full,
it will remove the earliest file automatically.
Playback
When open this page, the date of recorded files shows.
SD Card
70
The “.avi” extension name of the file means this file is a video file; the “.jpg” extension
name means it is a picture file. Click the file to start Microsoft Media Player to play it. If
the bandwidth is lower for playback directly, please right-click on the file and select
[Save As…] to download it to the PC, and then play the downloaded file with
Microsoft Media Player.
Note: the video format is compressed with H.264, the PC must install the H.264
decoder. You can install “FFdshow” from the included CD for the decoder.
Delete Recorded File
To delete the recorded file, check the check box of the file, then click [Del] button.
Format SD Card
If you want to empty the Micro-SD card, click [Format SD Card] to format the card.
To view the recorded files, just click the date, it will show the list of the recorded files.
Auto Deletion
If enable this function, the recorded files before the selected day will be deleted
automatically. After select the option, click [Apply] to save the setting.
71
6. Network Configuration
A. Intranet Only
Connects to PC Directly
If you want to connect the camera to PC directly for the very first time setup, please refer
to the figure below for the connection.
Ethernet Cable
Camera
This device supports Auto-MDI/MDIX,
PC
IP Address: 192.168.1.200
you can use a straight or cross-over
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
cable to connect these two devices.
Subnet Mask: 255.255.255.0
Gateway: (Empty)
Gateway: (Empty)
Http Port: 80
RTSP Port: 554
 Connect the camera to PC with Ethernet cable. The camera equips an
Auto-MDI/MDIX network connector, you can use a straight or cross-over Ethernet
cable.
 Refer to Configuration  Network  Network page to configure the IP settings.
 Please make sure the IP address of PC and camera are in the same subnet. Ex.
192.168.1.2 and 192.168.1.200 have the same subnet.
 Set Subnet Mask of PC and camera.
 Clear the Gateway of PC and camera to empty.
For example, if the IP settings have been configured as the above figure, the cameras can
be linked with following addresses:
Client
Camera
Link Address
PC
Camera
http://192.168.1.200
72
Remark
Connects to an Exist LAN
If the camera will be used in a local network (LAN) and don’t allow to access via Internet,
please refer to the figure below for the connection.
Intranet (LAN)
Camera 1
Switch
IP Address: 192.168.1.200
Router or IP Sharing
Subnet Mask: 255.255.255.0
IP Address: 192.168.1.254
Gateway: 192.168.1.254
Subnet Mask: 255.255.255.0
Http Port: 80
RTSP Port: 554
Camera 2
PC
IP Address: 192.168.1.201
IP Address: 192.168.1.2
Subnet Mask: 255.255.255.0
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Gateway: 192.168.1.254
Http Port: 80
RTSP Port: 554
 Connect the cameras to the Switch.
 Refer to Configuration  Network  Network page to configure the IP settings.
 Please make sure the IP address of Router, PC and camera are in the same subnet.
Ex. 192.168.1.2 and 192.168.1.200 have the same subnet.
 Set Subnet Mask of Router, PC and cameras.
 Set Gateway of PC and cameras with the same IP address. Usually, the Gateway is
the IP address of router.
 Set the IP address of a valid DNS into cameras. An invalid DNS will cause the
domain name can’t be resolved and reached, such as email address.
For example, if the IP settings have been configured as the above figure, the cameras can
be linked with following addresses:
Client
Camera
Link Address
Camera 1
http://192.168.1.200
Camera 2
http://192.168.1.201
PC
73
Remark
B. Internet Only
Connects to ADSL with Fixed Public IP Address
If the camera connects to Internet with an ADSL modem and the public IP address of
ADSL is fixed, please refer to the figure below for the connection.
Internet (WAN)
Camera
PC
3G Mobile Phone
IP Address: 60.220.20.250
Subnet Mask: 255.255.255.0
Gateway: 60.220.20.254
Http Port: 80
RTSP Port: 554
ADSL
 Connect the camera to the ADSL modem.
 Refer to Configuration  Network  Network page, configure the IP address,
Subnet Mask, Gateway and DNS with the settings that ISP provided for ADSL
connection.
For example, if the public IP address is “60.220.20.250”, now the camera can be linked
with following addresses:
Client
PC
Link Address
Remark
http://60.220.20.250
With audio:
3G Mobile
rtsp://60.220.20.250/3g
Phone
Without audio:
rtsp://60.220.20.250/3gx
74
Must enable “3GPP Stream” in
Configuration  Video/Audio
 Video Format page
Connects to ADSL with Floating Public IP Address (PPPoE)
If the camera connects to Internet with an ADSL modem and the public IP address of
ADSL is variable, the camera can use PPPoE function for the connection.
Internet (WAN)
Camera
PC
3G Mobile Phone
Configure the PPPoE Setting
ADSL
 Connect the camera to the ADSL modem.
 Refer to Configuration  Network  PPPoE page to configure the PPPoE settings.
 The camera will automatic dial-up and get the public IP address from ISP.
 If you have enable “Send Mail After Dialed” function, the camera will send an email
to tell you the current public IP address.
For example, if the public IP address is “60.220.20.250”, now the camera can be linked
with following addresses:
Client
PC
Link Address
Remark
http://60.220.20.250
With audio:
3G Mobile
rtsp://60.220.20.250/3g
Phone
Without audio:
rtsp://60.220.20.250/3gx
Must enable “3GPP Stream” in
Configuration  Video/Audio
 Video Format page
Using DDNS Function
Since the public IP address is variable, you can enable DDNS function to get a fixed
URL to instead of the IP address, refer to Configuration  Network  DDNS page to
configure and enable the DDNS function.
75
After enable the DDNS, assume the registered URL is “test.dyndns.org”, now the
camera can be linked with following URLs:
Client
PC
Link Address
Remark
http://test.dyndns.org
With audio:
3G Mobile
rtsp://test.dyndns.org/3g
Phone
Without audio:
rtsp://test.dyndns.org/3gx
76
Must enable “3GPP Stream” in
Configuration  Video/Audio
 Video Format page
C. Intranet + Internet
Connects to Internet with Fixed Public IP Address
If the camera will be added into a local network (LAN), and will be accessed via both
Intranet and Internet, please refer to the figure below for the connection.
Intranet (LAN)
Internet (WAN)
PC1
PC2
3G Mobile Phone
IP Address: 192.168.1.2
Camera 1
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
IP Address: 192.168.1.200
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Http Port: 80
Switch
ADSL
RTSP Port: 554
Public IP: 60.220.20.250
To allow the cameras can be linked through Internet, set
the NAT, Port Forwarding or Virtual Server as following:
Camera 2
WAN
IP Address: 192.168.1.201
Subnet Mask: 255.255.255.0
Gateway: 192.168.1.254
Router or IP Sharing
Http Port: 80
IP Address: 192.168.1.254
RTSP Port: 555
Subnet Mask: 255.255.255.0
LAN
Port
IP Address
Port
3081
192.168.1.200
80
554
554
192.168.1.200
3082
192.168.1.201
80
555
192.168.1.201
555
 Assume the local network will be connected to Internet with ADSL connection, first,
configure the router (or IP sharing) with the ADSL connection. Please refer to the
user’s manual of router for the configuration.
 Connect the cameras to the Switch.
 Refer to Configuration  Network  Network page to configure the IP settings.
 Configure the cameras with different IP address. Ex. assign camera1 to
192.168.1.200, and assign camera2 to 192.168.1.201
 Please make sure the IP address of Router, PC and cameras are in the same subnet.
Ex. 192.168.1.2 and 192.168.1.200 have the same subnet.
77
 Set Subnet Mask of Router, PC and cameras.
 Set Gateway of PC and cameras with the same IP address. The Gateway is the IP
address of router.
 Set the IP address of a valid DNS into cameras. An invalid DNS will cause the
domain name can’t be resolved and reached, such as email address.
 Configure the cameras with different RTSP port. Ex. assign camera1 with port 554,
and assign camera2 with port 555.
 To allow the cameras can be linked through Internet, set router’s NAT (Network
Address Translation), Port Forwarding or Virtual Server as following:
WAN Side
LAN Side
Camera
Remark
Port
Protocol IP Address
Port Protocol
3081
TCP
192.168.1.200
80
TCP
Port for Web page
554
TCP
192.168.1.200
554
TCP
Port for Video and
Audio
3082
TCP
192.168.1.201
80
TCP
Port for Web page
555
TCP
192.168.1.201
555
TCP
Port for Video and
Audio
Camera 1
Camera 2
For example, if the IP settings have been configured as the above figure, the cameras can
be linked with following addresses:
Clients in
Intranet
Camera
Link Address
Camera 1
http://192.168.1.200
Camera 2
http://192.168.1.201
Camera
Link Address
Camera 1
http://60.220.20.250:3081
Camera 2
http://60.220.20.250:3082
Camera 1
With audio:
rtsp://60.220.20.250:554/3g
Without audio:
rtsp://60.220.20.250:554/3gx
Remark
PC1
Client from
Internet
Remark
PC2
3G Mobile
Phone
78
Must enable “3GPP
Stream” in Configuration
 Video/Audio  Video
Format page
Camera 2
With audio:
rtsp://60.220.20.250:555/3g
Without audio:
rtsp://60.220.20.250:555/3gx
Connects to Internet with Floating Public IP Address
If the public IP address of ADSL connection is variable, you can enable DDNS function to
get a fixed URL to instead of the IP address.
Note: only one device can enable the DDNS function in the local network (LAN), multiple
devices use DDNS will update to the DDNS provider too frequently, and the DDNS
provider will block your URL.
If the router has DDNS function, use router’s DDNS function is recommended. Please
refer to the user’s manual of router for the configuration.
If the router doesn’t have DDNS function, use one of the cameras DDNS function is
recommended. Refer to Configuration  Network  DDNS page to configure and enable
the DDNS function.
After enable the DDNS, assume the registered URL is “test.dyndns.org”, now the cameras
can be linked with following URLs:
Client from
Internet
Camera
Link Address
Camera 1
http://test.dyndns.org:3081
Camera 2
http://test.dyndns.org:3082
Camera 1
With audio:
rtsp://test.dyndns.org:554/3g
Without audio:
rtsp://test.dyndns.org:554/3gx
Camera 2
With audio:
rtsp://test.dyndns.org:555/3g
Without audio:
rtsp://test.dyndns.org:555/3gx
Remark
PC2
3G Mobile
Phone
79
Must enable “3GPP
Stream” in Configuration
 Video/Audio  Video
Format page
7. Factory Default
To recover the default password and other settings, please follow the steps:
1. Power off this device.
2. Use a needle about 5cm long insert into the "Factory Default Hole" and push the
button in the hole, keeping push it and don't release.
Factory Default Hole
3. Power on the device. Don’t release the button during the system booting.
4. It will take around 30 seconds to boot the device.
5. Release the button when the device finishes proceed.
6. Re-login the device using the default username (admin) and password (admin).
7. The IP address is probably restored to the default, in this case, use IP Search
utility to search the device. The default IP address is 192.168.1.200
80
Compatible List of SD Card
The Compatible List of SD Card
Recommended Micro-SD Card
The speed of SD card must be “Class 4”, “Class 6” or higher speed.
SanDisk 128M
ADATA 512M
SanDisk 256M
ADATA 4G
SanDisk 512M
Toshiba 128M
SanDisk 1G
Toshiba 256M
SanDisk 2G
Toshiba 4G
SanDisk 4G
Kingston 128M
SanDisk 8G
Kingston 256M
SanDisk 16G
Kingston 512M
SanDisk 32G
Kingston 1G
Transcend 4G
Kingston 32G
Transcend 8G
Transcend 16G
Transcend 32G
81
Download PDF