Sun -4e -4 workstation Handbook

Sun-4 Handbook - Home Page

Sun Internal ONLY

!!

The Sun-4 Handbook describes and illustrates the Sun-4 and

Sun-4e products for service providers who service these products after the End of Support Life in April 1997.

End of Support Life is the end of Sun's commitment to support the product. Sun may help customers locate alternative sources for support on a case-by-case basis if ongoing support is needed beyond 5 years. Spares availability after End of Support Life may be limited and repair service will be at Sun's discretion.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00000/wcd00036.htm (1 von 2) [25.04.2002 15:56:23]

Sun-4 Handbook - Home Page

[ Configurations

] [

CPU

] [

Memory

] [ Graphics

] [ IPI ] [

SCSI ] [

SCSI Disk

]

[ Removable Media ] [

Communication

] [

Miscellaneous ] [

Backplane ] [

Slot Assignment

]

[

Parts Introduction ] [

System ] [

Disk Options

] [

Removable Media Options ]

[ Miscellaneous Options

] [ Board ] [

Input Device ] [

Monitor

] [ Printer

]

[ CPU Trouble

] [ Disk Trouble ] [

Diagnostics

]

[

Power Introduction

] [

AC Power ] [

DC Power ]

The original hardcopy publication of the Sun-4 Handbook is part number 805-3028-01 .

© 1987-1999, Sun Microsystems Inc.


Sun4/II: DC Power - Contents

DC Power

Power Supplies

300-1020 -- Brown -- 575 Watts

300-1020 -- Fuji -- 575 Watts

300-1022 -- Summit -- 325 Watts

300-1022 -- Brown -- 325 Watts

300-1024 -- Fuji -- 850 Watts

300-1031 -- Delta -- 120 Watts

300-1034 -- Boschert -- 520 Watts

300-1041 -- Seagate -- 205 Watts

300-1043 -- Fuji -- 925 Watts

300-1045 -- Boschert -- 130 Watts

300-1047 -- Zytec -- 925 Watts

300-1052 -- Fuji -- 820 Watts

300-1056 -- Fuji -- 410 Watts

300-1065 -- Zytec -- 1200 Watts

300-1072 -- Boschert -- 520 Watts

300-1074 -- Seagate -- 215 Watts

300-1075 -- Fuji -- 840 Watts

300-1085 -- Zytec -- 268 Watts

300-1089 -- Fuji -- 925 Watts

300-1091 -- Fuji -- 820 Watts

300-1106 -- Fuji -- 800 Watts

OEM Product Power Supplies

811-1027 -- Fujitsu

811-1242 -- HP

Last updated: March 14, 1997

Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f0.htm [25.04.2002 15:56:27]

Sun4/II: Power - Brown 300-1020

Brown 300-1020

575 Watt Power Supply

Sun-4/150/350

300-1020 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006b9.htm (1 von 2) [25.04.2002 15:56:34]

Sun4/II: Power - Brown 300-1020

Fuse

10 Amps @ 250 Volts

Last updated: December 2, 1996

Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006b9.htm (2 von 2) [25.04.2002 15:56:34]

Sun4/II: Power - Fuji PEX445-30 575 Watt Power Supply

Fuji PEX445-30


Sun-4/150/350

300-1020 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ba.htm (1 von 2) [25.04.2002 15:56:39]


Fuse

15 Amps @ 250 Volts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ba.htm (2 von 2) [25.04.2002 15:56:39]

Sun4/II: Power - Summit CS0325-9001 325 Watt Power Supply

Summit CS0325-9001


Sun-4/110/310

300-1022 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bb.htm (1 von 2) [25.04.2002 15:56:45]

Sun4/II: Power - Summit CS0325-9001 325 Watt Power Supply

Fuse

7 Amps @ 250 Volts

Note

Wait at least two minutes after power down or power outage before turning power ON to allow the unit to reset.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bb.htm (2 von 2) [25.04.2002 15:56:45]

Sun4/II: Power - Brown PS41 325 Watt Power Supply

Brown PS41


Sun-4/110/310

300-1022 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bc.htm (1 von 2) [25.04.2002 15:56:54]

Sun4/II: Power - Brown PS41 325 Watt Power Supply

Fuse:

7 Amps @ 250 Volts

Note

Wait at least two minutes after power down or power outage before turning power ON to allow the unit to reset.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bc.htm (2 von 2) [25.04.2002 15:56:54]

Sun4/II: Power - Fuji PEX391 850 Watt Power Supply

Fuji PEX391


Sun-4/260/280/360/380

300-1024 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bd.htm (1 von 2) [25.04.2002 15:56:57]

Sun4/II: Power - Fuji PEX391 850 Watt Power Supply

Fuse

Note

30 Amps @ 250 Volts

The Fuji 300-1024 is the same as the Fuji 300-1016.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bd.htm (2 von 2) [25.04.2002 15:56:57]

Sun4/II: Power - Delta DPS-118AB 120 Watt Power Supply

Delta DPS-118AB


Options 526 / 527 / 530 / 539 / 561 / 563 / 565

Options 566 / RR126 / RR128 / RR129 / RREXP

300-1031

Fuses

4 Amps @ 250 Volts

3 Amps @ 250 Volts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006be.htm (1 von 2) [25.04.2002 15:57:05]

Sun4/II: Power - Delta DPS-118AB 120 Watt Power Supply


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006be.htm (2 von 2) [25.04.2002 15:57:05]

Sun4/II: Power - Boschert XL520-3625 520 Watt Power Supply

Boschert XL520-3625


Sun-4/330

300-1034 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bf.htm (1 von 2) [25.04.2002 15:57:11]


Fuses

F1 = 20 Amps @ 250 volts

F2 = 10 Amps @ 250 volts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006bf.htm (2 von 2) [25.04.2002 15:57:11]

Sun4/II: Power - Seagate 45070622 205 Watt Power Supply

Seagate 45070622


Seagate 97209-12G Disk Drive

Options 706 / 707 / 709 / 710

300-1041

Fuse

Soldered at F 100, 8 Amps @ 250 Volts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c0.htm (1 von 2) [25.04.2002 15:57:18]


Notes

205 Watt Power Supply 300-1041

Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive.

Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive.


Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drives.



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c0.htm (2 von 2) [25.04.2002 15:57:18]


Fuji PEX479-30


Sun-4/260/280/360/380

300-1043 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c1.htm (1 von 2) [25.04.2002 15:57:24]


Fuse

Littelfuse 30A 250V BLN 30

Note

Use wire harnesses 530-1578 and 530-1580 for the 80/280/380/480 chassis. Use wire harnesses

530-1578 and 530-1581 for the 160/260/360/460 chassis.






Options 501 / 503 / 504 / 505 / 506 / 507

Options 509 / 510 / 511 / 514 / 516



Fuse

Note

5 Amps @ 250 Volts

Use Power Harness, 530-1432-01, for this power supply.



Sun4/II: Power - Zytec 22903110 925 Watt Power Supply

Zytec 22903110


Sun-4/370/470

Options 509 / 510 / 511 / 514 / 516

300-1047

DC OUTPUT REGULATION FULL LOAD

+5

-5.2

+12 analog

150 Amps

15 Amps

15 Amps

145.0 Amps

10.0 Amps

2.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c3.htm (1 von 2) [25.04.2002 15:57:32]


+12 motor

-12

15 Amps

10 Amps

6.3 Amps

4.0 Amps




Fuji PEX527-30


Options 733 / 734



Fuse

20 Amps @ 250 Volts

Notes

820 Watt Power Supply 300-1052-02

Supports four CDC 9720-688 Disk Drives.

Supports four Fujitsu M2372K Disk Drives.



Does not support the Fujitsu M2372K Disk Drive.

Supports two Seagate 97209-12G 3MB/Sec IPI Disk Drives.

Does not Support Seagate 97229-11G 6MB/Sec IPI Disk Drives.




Supports four Seagate 97209-12G 3MB/Sec IPI Disk Drives.




Supports four Fujitsu M2372K Disk Drives.






Fuji PEX527-40


Options 731 / 732



Fuse

20 Amps @ 250 Volts

Notes


Supports two CDC 9720-688 Disk Drives.

Supports two Fujitsu M2372K Disk Drives.









Supports two Fujitsu M2372K Disk Drives.




Zytec 22907400


Sun-4/390/490

SS690

300-1065


+5 10-200 Amps 200.0 Amps

-5.2

+12 analog

0.4-15 Amps

0-10 Amps

10.0 Amps

2.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c6.htm (1 von 2) [25.04.2002 15:57:52]


+12 motor

-12

4-15 Amps

0-5 Amps

6.3 Amps

4.0 Amps






Sun-4/330 / SS630



Fuses

F1 = 20 Amps @ 250 Volts

F2 = 10 Amps @ 250 Volts




Seagate 45070625


Seagate 97209-12G / Seagate 97229-11G

Options 706 / 707 / 709 / 710 / 716 / 717 / 719 / 720

300-1074

Fuse

At F 100, 8 Amps, 250 Volts, LittleFuse, 312-008 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006c8.htm (1 von 2) [25.04.2002 15:58:13]


Notes


Supports one Seagate 97209-12G 3MB/Sec IPI Disk Drive.

Does NOT Support the Seagate 97229-11G 6MB/Sec IPI Disk Drive.







Fuji PEX527-31


Options 741 / 742 / 743 / 744



Fuse

20 Amps @ 250 Volts

Notes




Does not support Fujitsu M2372K Disk Drives.

Does not support CDC 9720-688 Disk Drives.




Zytec 22914300


Options 726 / 727

300-1085 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ca.htm (1 von 2) [25.04.2002 15:58:25]


Fuse

10 Amps @ 250 Volts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ca.htm (2 von 2) [25.04.2002 15:58:25]


Fuji PEX526-30


Sun-4/370/470

300-1089


+5 150 Amps 145.0 Amps

-5.2

+12 analog

15 Amps

15 Amps

10.0 Amps

2.0 Amps

+12 motor

-12

15 Amps

10 Amps

6.3 Amps

4.0 Amps http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cb.htm (1 von 2) [25.04.2002 15:58:28]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cb.htm (2 von 2) [25.04.2002 15:58:28]


Fuji PEX614-30


Options 750 / 754 / 756

300-1091 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cc.htm (1 von 2) [25.04.2002 15:58:34]


Fuse

Littelfuse BLN 20


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cc.htm (2 von 2) [25.04.2002 15:58:34]


Fuji PEX614-31


Options 750 / 754 / 756 / 762 / 763 / 764

300-1106 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cd.htm (1 von 2) [25.04.2002 15:58:39]


Fuse

Littelfuse BLN 20


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cd.htm (2 von 2) [25.04.2002 15:58:39]

Sun4/II: Power - Fujitsu M2444AC Power Supply

Fujitsu M2444AC Power Supply A-1

Options 78 / 675

811-1027 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (1 von 3) [25.04.2002 15:58:51]


Fujitsu M2444AC Power Supply A-2

Options 78 / 675

811-1027 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (2 von 3) [25.04.2002 15:58:51]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ce.htm (3 von 3) [25.04.2002 15:58:51]

Sun4/II: Power - HP 88780 Power/Motor Drive Power Supply

HP 88780 Power/Motor Drive Power

Supply

Options 680 / 682 / 683 / 684

811-1242

Note

Use 6 Amp fuse 140-1021-01.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006cf.htm [25.04.2002 15:58:55]

Sun4/II: AC Power - Contents

AC Power

AC Power Sequencer

Remote and Local Bus Connectors

Power Requirements

300-1011 -- Pulizzi Engineering -- 115V





370-1155-02 -- Sherwood Enterprises -- 230V

300-1263 -- Sherwood Enterprises -- 230V

370-1156-03 -- Sherwood Enterprises -- 240V

300-1264 -- Sherwood Enterprises -- 240V

Last updated: February 6, 1997

Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ed.htm [25.04.2002 15:59:01]

Sun4/II: Power - AC Power Sequencer

AC Power Sequencer

Remote and Local Bus Connectors

300-1011 / 300-1263 / 300-1264

370-1126 / 370-1127 / 370-1155 / 370-1156

Remote I/O Connectors J6, J7, J8, and J9

A parallel circuit connects J6, J7, J8, and J9. Inputs to the Remote I/O Connectors are activated by mechanical toggle, key switch, transistor, integrated circuit, or thermoswitch with a normal open configuration.

CONNECTOR PART NUMBER USED WITH PART NUMBER

Female

Male

AMP 1-480304-0

AMP 1-480305-0

Socket Terminals

Contact Pins

AMP 60619-1

AMP 60620-1

Cable Description

Use 3-conductor, #22 AWG stranded wire.

Remote - OFF - Local Switch

POSITION DESCRIPTION

REMOTE AC output of the Switched 1 and Switched 2 outlets is enabled when the breaker is ON and the Power Request is connected to Signal Return on the Remote I/O Connectors.

OFF The AC output of the Switched 1 and Switched 2 outlets is disabled.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069d.htm (1 von 2) [25.04.2002 15:59:04]

Sun4/II: Power - AC Power Sequencer

LOCAL The AC output of the Switched 1 and Switched 2 outlets is enabled when the Circuit Breaker is ON.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069d.htm (2 von 2) [25.04.2002 15:59:04]

Sun4/II: Power - AC Sequencer Power Requirements

AC Sequencer Power Requirements

300-1011 / 300-1027 / 300-1263

300-1264 / 370-1126 / 370-1155 / 370-1156

Operating Range

Nominal Voltage: 208, 220, 230, or 240 Volts AC

Operating Voltage: Single Phase 180-264 Volts AC

Frequency: 48-63 Hz

Current: 24 A maximum

AC Power Plug

The 230VAC power plug is a NEMA L6-30P. The 240VAC power plug is a Blue, 32A, IEC 309, with

Ground at the 6-hour position.

230V Sequencer AC Power Cord

A 12 AWG Type SJO flexible cord rated at 25A when connected to utilization equipment with 2 current carrying conductors is used. Refer to Article 400-5 of the US National Electrical Code.

NEMA L6-30R / ANSI C73.75 230 Volt Power

Receptacle http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069e.htm (1 von 2) [25.04.2002 15:59:07]

Sun4/II: Power - AC Sequencer Power Requirements

IEC 309 240 Volt Power Receptacle


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069e.htm (2 von 2) [25.04.2002 15:59:07]

Sun4/II: Power - Pulizzi Engineering PC874C and PC874D

115 Volt AC Power Sequencer

300-1011

Pulizzi Engineering PC874

Outlet Side

Control Side

Notes

1. Requires AC outlet NEMA L5-30R, 30A, 125V.

2. Any conversion to the Data Center Cabinet, including replacement of the AC Power Plug or AC

Power Sequencer, voids all safety agency approvals.

3. The Switched 2 output comes on after a 5 second delay.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069f.htm (1 von 2) [25.04.2002 15:59:11]

Sun4/II: Power - Pulizzi Engineering PC874C and PC874D

References

1. Installation Manual for the Sun Full-height Rack System, 800-1555.

2. Installation Manual for Sun Rackmountable Fileservers, 800-1556.

3. Sun Full-Height Rack System Installation Manual, 800-1677.

4. Sun Rackmountable Fileservers Installation Manual, 800-1676.

5. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0069f.htm (2 von 2) [25.04.2002 15:59:11]

Sun4/II: Power - Pulizzi Engineering PC874C and PC874D 230 Volt AC Power Sequencer


370-1027 370-1155

Pulizzi Engineering

PC874

Pulizzi Engineering

PC874

Outlet Side

Control Side

Notes




3. The Switched 2 output of 370-1127 comes on after a 5-second delay.

4. The Switched 2 output of 370-1155 comes on after a 20 sec delay.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006a0.htm (1 von 2) [25.04.2002 15:59:14]


References

1. Sun Full-Height Rack System Installation Manual, 800-1677.

2. Sun Rackmountable Fileservers Installation Manual, 800-1676.

3. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036.

4. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual,

800-3242.

5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18.

6. Sun 56-inch Cabinet Service Manual, 800-6371-17.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006a0.htm (2 von 2) [25.04.2002 15:59:14]



370-1126 370-1156

Pulizzi Engineering

PC874

Pulizzi Engineering

PC874

Outlet Side

Control Side

Notes

1. Requires a Blue, IEC 309, 2-Pole, 3-Wire, 32A, 250V AC receptacle.



3. The AC Power Cord is internally wired to the AC Line Filter.





References

1. Sun Full-Height Rack System Installation Manual, 800-1677.

2. Sun Rackmountable Fileservers Installation Manual, 800-1676.

3. Sun 900 Mbyte Disk Drive Installation Manual, 800-1036.

4. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual,

800-3242.

5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18.

6. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17.



Sun4/II: Power - Sherwood Enterprises 230 Volt AC Power Sequencer


370-1155-02

Sherwood Enterprises

Outlet Side

Control Side

Notes




3. The Switched 2 output comes on after a 20-second delay.

References




4. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual,

800-3242.



5. Sun 56-inch Expansion Cabinet Installation Manual, 800-5936-18.

6. Sun 56-inch Expansion Cabinet Service Manual, 800-6371-17.



Sun4/II: Power - Sherwood Enterprises 230 Volt AC Power Sqncr 1263


300-1263


Outlet Side

Control Side

Notes





4. The 300-1263 replaced 370-1155-02 in February 1996.

References




Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006a3.htm [25.04.2002 15:59:29]



370-1156-03


Outlet Side

Control Side

Notes




3. The AC Power Cord is internally wired to the AC Line Filter.




References




4. Sun 56-inch Data Center Cabinet and Data Center Expansion Cabinet Installation Manual,

800-3242.





Sun4/II: Power - Sherwood Enterprises 240 Volt AC Power Sqncr 1264


300-1264


Outlet Side

Control Side

Notes





4. The 300-1264 replaced 370-1156-03 in February 1996.

References





II: Power - Introduction - Contents

Power - Introduction

AC Power Cords

Fuses

Wire Harnesses

Sun 5-Slot Office Pedestal Wiring Diagram

Sun 12-Slot Office Pedestal Wiring Diagram

Sun 16-Slot Logic Enclosure Wiring Diagram


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ea.htm [25.04.2002 15:59:41]

II: Power - AC Power Cords

AC Power Cords

PART # DESCRIPTION

180-1010 IEC 320 - Reverse IEC 320, Coiled (obs)

180-1117 IEC 320 - Reverse IEC 320

180-1097 IEC 320 - NEMA 5-15, 15A/125V

180-1125 IEC 320 - pigtail, 6A/250V

180-1126 IEC 320 - NEMA 6-15, 10A/250V (obs)

180-1142 IEC 320 - NEMA 5-15, 15A/125V

180-1146 IEC 320 - NEMA 5-15, 10A/125V

180-1176 IEC 320 - BS 1363, 10A/250V (obs)

180-1177 IEC 320 - CEE 7/7, 10A/250V (obs)

180-1177 IEC 320 - CEE 7/7, 10A/250V (obs)

180-1177 IEC 320 - CEE 7/7, 10A/250V (obs)

180-1178 IEC 320 - SEV 1011, 10A/250V (obs)

180-1178 IEC 320 - SEV 1011, 10A/250V (obs)

180-1178 IEC 320 - SEV 1011, 10A/250V (obs)

180-1179 IEC 320 - NEMA 5-15, 10A/250V

180-1179 IEC 320 - NEMA 5-15, 10A/250V

180-1183 Y IEC 320 - NEMA 6-15, 10A/250V

180-1184 Y IEC 320 - Reverse IEC 320, 10A/250V

180-1189 IEC 320 - NEMA 6-15, 10A/250V

180-1190 IEC 320 - Reverse IEC 320, 10A/250V

180-1234 IEC 320 - 107/10-1973, 10A/250V (obs)

180-1235 IEC 320 - CEI 23-16/VII, 10A/250V (obs)

180-1236 IEC 320 - AS 3112, 10A/250V (obs)

Japan

V3 Sequencer

V4 Sequencer

V3 Sequencer

V4 Sequencer

Denmark

Italy

Australia

180-1683 IEC 320 - Reverse IEC 320, 10A/250V, 1.5M V4 Sequencer

180-1688 IEC 320 - Reverse IEC 320, 10A/250V, 2.5M V4 Sequencer

180-1732 90° IEC 320 - 90° Reverse IEC 320, .75M

530-1343 IEC 320 - Reverse IEC 320, 10A/250V

E150 Internal

V4 Sequencer

530-1351 IEC 320 - NEMA 6-15, 10A/250V

530-1370 IEC 320 - NEMA 5-15, 15A/125V, Grey

V3 Sequencer

USA

530-1371 IEC 320 - Reverse IEC 320, 15A/125V, Grey PBox Acc Pwr

530-1410 IEC 320 - CEE 7/7, 6A/250V, Grey Europe

USAGE

Acc Pwr

Acc Pwr

USA

Acc Pwr

V3 Sequencer

USA

USA

UK

France

Germany

Sweden

France

Germany

Switzerland

USA

530-1411 IEC 320 - BS 1363, Grey

530-1583 IEC 320 - SEV 1011, 10A/250V, Grey

UK

Switzerland

530-1584 IEC 320 - CEI 23-16/VII, 10A/250V, Grey Italy

530-1585 IEC 320 - 107/10-1973, 10A/250V, Grey Denmark

530-1586 IEC 320 - AS 3112, 10A/250V, Grey

530-1604 IEC 320 - CEE 7/7, 10A/250V, Grey

Australia

S. America http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e8.htm (1 von 3) [25.04.2002 15:59:45]


530-1657 90° IEC 320 - NEMA 5-15, 10A/125V, Grey USA

530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Grey

530-1663 90° IEC 320 - CEE 7/7, 10A/250V, Grey

France

Germany

530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey

530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey

France

Germany

530-1664 90° IEC 320 - SEV 1011, 10A/250V, Grey Switzerland

530-1665 90° IEC 320 - CEI 23-16/VII, 10A/250V, Grey Italy

530-1666 90° IEC 320 - 107/10-1973, 10A/250V, Grey Denmark

530-1667 90° IEC 320 - AS 3112, 10A/250V, Grey Australia

530-1668 90° IEC 320 - CEE 7/7, 10A/250V, Grey

530-1671 90° IEC 320 - BS 1363, 6A/250V, Grey

S. America

UK

530-1817 IEC 320 - CEE 7/7, 10A/250V

530-1817 IEC 320 - CEE 7/7, 10A/250V

530-1817 IEC 320 - CEE 7/7, 10A/250V

530-1818 IEC 320 - SEV 1011, 6A/250V

France

Germany

Sweden

France

530-1818 IEC 320 - SEV 1011, 6A/250V

530-1818 IEC 320 - SEV 1011, 6A/250V

530-1819 IEC 320 - 107/10-1973, 10A/250V

530-1820 IEC 320 - CEI 23-16/VII, 10A/250V

530-1821 IEC 320 - BS 1363, 10A/250V

530-1822 IEC 320 - AS 3112, 10A/250V

530-2073 Type C7 - BS1363A, 5A/250V

530-2074 Type C7 - CEE 7/7, 2.5A/250V

530-2075 Type C7 - SAA/2, 7.5A/250V

530-2076 Type C7 -NEMA 1-15, 15A/125V

530-2122 Type C7 - JIS-C 8303

530-2160 IEC320 C19 to IEC320 C20, 610 mm

530-2188 IEC320 C19 to IEC320 C20, 1050 mm

530-2197 IEC320 C13 to AMP Mate-N-Lok

530-2197 IEC320 C13 to AMP Mate-N-Lok

530-2213 IEC320 C19 to IEC320 C20, 2500 mm

530-2264 AMP Mate-N-Lok to Y IEC320 C13

530-2264 AMP Mate-N-Lok to Y IEC320 C13

530-2265 Han 6HsB to NEMA L6-30P, Option 3800

530-2265 Han 6HsB to NEMA L6-30P, Option 3800

E5000/E6000

Option 956

E5000/E6000

Option 956

530-2266 Han 6HsB to Blue 32A IEC309, Option 3848 E5000/E6000

530-2266 Han 6HsB to Blue 32A IEC309, Option 3848 Option 956

530-2301 IEC320 C13 to Blue 32A IEC309, Option 389 Danish E4000

Germany

Switzerland

Denmark

Italy

UK

Australia

UK

Europe

Australia

USA

Japan

SC2000

SC2000

E5000/E6000

Option 956

E5000/E6000

Warning

The Schuko CEE 7/7 plug is not grounded if used with the Danish Afsnit 107 electrical outlet.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e8.htm (2 von 3) [25.04.2002 15:59:45]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e8.htm (3 von 3) [25.04.2002 15:59:45]

II: Power - Fuses

Fuses

FUSE SIZE SUN PART # VENDOR

1/16A .25 x 1.25" 140-1004 Littelfuse

1/16A .25 x 1.25" 140-1004 Bussman

1/8A .25 x 1.25" 140-1003 Littelfuse

1/8A .25 x 1.25" 140-1003 Bussman

1/2A .25 x 1.25" 140-1012 Littelfuse

3/4A PICO II 140-1024 Littelfuse

3/4A .145 x .30" 140-1024 Bussman

3/4A .25 x 1.25" 140-1044 Littelfuse

1A .25 x 1.25" 140-1040 Littelfuse

1A Microfuse 140-1027 Littelfuse

1A .25 x 1.25" 140-1040 Littelfuse

1A .25 x 1.25" 140-8500 Bussman

1A .25 x 1.25" 140-8500 Littelfuse

1.5A Microfuse 150-1162 Littelfuse

1.5A Microfuse 150-1383 Littelfuse

1.5A 5 x 20mm 150-1208 SOC

1.5A .25 x 1.25" 140-1042 Littelfuse

1.6A .25 x 1.25" 140-1022 Littelfuse

1.6A .25 x 1.25" 140-1022 BEL

MT4-1.51

313 01.5

312 01.6

3AG1.6

1.6A .25 x 1.25" 140-1022 Pwr Dynam ics 19340 1.6A

1.6A .25 x 1.25" 140-1022 Bussman AGC 1.6A

1.6A 5 x 20mm 150-1215 Schurter

1.6A 5 x 20mm 150-1215 Littelfuse

034.3119

218 01.6

2A .25 x 1.25" 140-1005 Littelfuse

2A .25 x 1.25" 140-1005 Bussman

2A PICO II 140-1028 Littelfuse

2A 5 x 20mm 140-1034 Bussman

2A 5 x 20mm 140-1034 Littelfuse


2A .25 x 1.25" 150-1191 MGC

2A .25 x 1.25" 150-1191 Littelfuse

312 002

AGC 2

252 002

GDC-2

218 002

273 002

MGC 0002

312 002

2A .25 x 1.25" 140-1048 Littelfuse

2A .25 x 1.25" 140-1048 Bussman

2.5A .25 x 1.25" 140-1000 Littelfuse

2.5A .25 x 1.25" 140-1000 Bussman

2.5A .25 x 1.25" 140-1008 Littelfuse

2.5A .25 x 1.25" 140-1008 Bussman

PART #

312.062

AGC 1/16

312.125

AGC 1/8

313.500

255.750

GFA 3/4

312 .750

313 001

273 001

313 001

AGC-1

314 001

273 01.5

273 01.5

313 002

MDA 2

313 02.5

MDA 2 1/2

313 003

MDA 2 1/2 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e9.htm (1 von 5) [25.04.2002 15:59:56]

II: Power - Fuses

3A .25 x 1.25" 150-1034 Littelfuse


3A .145 x .30" 140-1038 Bussman

3A .25 x 1.25" 150-1034 Bussman

3A .25 x 1.25" 140-1039 Littelfuse


3A Microfuse 150-1698 Bussman

3.15A 5 x 20mm 140-1002 Bussman


4A 5 x 20mm 140-1031 Schurter


4A .25 x 1.25" 140-1001 Littelfuse

4A .25 x 1.25" 140-1001 Bussman

4A .25 x 1.25" 140-1007 Littelfuse

4A .25 x 1.25" 140-1007 Bussman

313 003

252 003

A3XRAD

MDA-3

312 003

273 003

GMW-3

GDC 3.15

218 315

FST 034.3123

218 004

318 004

AGC4AMP

312 004

MTH 4

4A .25 x 1.25" 140-1020 Littelfuse

4A .25 x 1.25" 140-1020 BEL

313 004

3SB4

4A .25 x 1.25" 140-1020 Pwr Dynamics 19341-4A

4A .5 x 20mm 140-1043 Littelfuse 217 004

4A .25 x 1.25" 150-1033 Littelfuse

4A .25 x 1.25" 150-1033 Bussman

5A .25 x 1.25" 140-1010 Littelfuse

5A .25 x 1.25" 140-1010 Bussman

313 004

MDA 4A,250V

313 005

MDA (5 AMP)


5A 5 x 20mm 140-1025 BEL




5A .25 x 1.25" 140-1041 Littelfuse


6A 5 x 20mm 140-1009 Bussman

034.3914

5MT5

218 005

034.3124

218 005

312 005

212 06.3

GMA 6

6A .25 x 1.25" 140-1011 Littelfuse

6A .25 x 1.25" 140-1011 Bussman

6A .25 x 1.25" 140-1021 Littelfuse

6A .25 x 1.25" 140-1021 Bussman

314 006

ABC 6A 250V

312 006

MTH-6A

6A .25 x 1.25" 140-1021 Pwr Dynamics 19340-6A

6A .25 x 1.25" 140-1026 Bussman 250(MSL)

6A 5 x 20mm 150-0473 Pnl Compnt


341524

213 006

6.3A 5 x 20mm 140-1030 Schurter


FST 034.3125

218 063 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006e9.htm (2 von 5) [25.04.2002 15:59:56]

II: Power - Fuses

7A .25 x 1.25" 150-1258 Littelfuse

7A .25 x 1.25" 150-1258 Bussman

8A .25 x 1.25" 140-1006 Littelfuse

8A .25 x 1.25" 140-1006 Bussman



10A .25 x 1.25" 140-1017 Littelfuse

15A .25 x 1.25" 140-1035 Littelfuse

15A .25 x 1.25" 140-1035 Bussman

15A 0.46 x 1.5" 140-1154 Littelfuse

15A 0.46 x 1.5" 140-1154 Bussman

15A Nano 2 150-2330 Littelfuse


15A 0.46 x 1.5" 150-xxxx Littelfuse

30A Autofuse None Littelfuse

313 007

MDQ-7

314 008

MTH 8

217 008

034.1525

326 010

10A .25 x 1.25" 140-1017 Pwr Dynamics 19341-10A

10A .25 x 1.25" 140-1051 Littelfuse 314 010

10A .25 x 1.25" 140-1051 Bussman

10A 0.46 x 1.5" 140-1152 Littelfuse

ABC-10A

KLK-R 10A

12A .25 x 1.25" 140-8000 Bussman

12A .25 x 1.25" 140-8000 Littelfuse

15A .25 x 1.25" 140-1019 Littelfuse

15A .25 x 1.25" 140-1019 Bussman

ABC-12

314.012

314 015

ABC-15A

314 015

ABC-15A

CCM-R 15A

LP-CC-15

451 015

251 015

CCMR 15A

257030

Fuseholder and Fusecarrier

Follow these instructions to avoid electrical shock hazard when wiring the type of fuseholder illustrated below.

1. Connect the AC Input to the Terminal on the end of the Fuse holder.

2. Connect the Terminal on the side of the Fuseholder to the AC Line Filter or AC Switch.

DESCRIPTION

Carrier, Domestic

Carrier, International

SUN PART # VENDOR

150-1042 Schurter

150-1051 Schurter

PART #

FEK 031.1666

031.1663


II: Power - Fuses

Holder, In Line 22-14AWG 140-1023 AMP

Holder, In Line 22-14AWG 140-1023 Littelfuse

Holder, UL/CSA/VDE 150-1041 Schurter

Holder, R/A for PIG-TAIL 150-1163 Littelfuse

Holder, R/A for PIG-TAIL 150-1163 Pwr Dynam ic

Holder, 20A,250V,UL

Microfuse Holder

150-1177

150-1179

Schurter

Littelfuse

552844-1

155 020U

FEU 031.1693

281 007

19557

FEU031.1673

282 002

Microfuse Holder

Holder

Holder, Faston Type

Holder, Faston Type

Holder, Quick Connect

Holder, Quick Connect

Field Engineers Fuse Kit

150-1179

150-1024

150-1026

150-1026

150-1029

150-1029

555-1126

Littelfuse

Littelfuse

Littelfuse

Bussman

Bussman

Littelfuse

Sun

282 008

345 001

571 007

HPF

HTA-HH

342 858

555-1126

Subminiature Microfuses

Subminiature microfuses are used on many Sun Printed Circuit Boards. Subminiature microfuses are field replaceable.

PICO II Fuses

PICO II fuses are used on Printed Circuit Boards and Peripheral devices such as Tape and Disk

Drives. PICO II fuses are not field replaceable because they are soldered in place.


II: Power - Fuses

PTCs

Positive Temperature Coefficient (PTC) thermistors are resistors with a high positive temperature coefficient of resistance. The PTC is used as a self-resetting fuse in overload applications. When an overload current flows through a PTC, there is a specific time period before the PTC heats up to its high-resistance state and starts limiting the current. PTCs are not field replaceable because they are soldered in place.



II: Power - Wire Harnesses

Wire Harnesses

Wire Harness Color Codes

The most common wire insulation colors used on Sun AC and DC wire harnesses are shown in the charts below. Not all products conform to these color codes.

AC Wire Harnesses

Color Abbreviation Description

Green Grn AC Ground

Black Blk AC Line (Hot)

Green/Yellow Grn/Yel AC Ground

Blue

Brown

Blu

Brn

AC Neutral

AC Line (Hot)

DC Wire Harnesses

Color Abbreviation Description

White

Yellow

Wht

Yel

-5Vdc

-5.2Vdc

Blue

Brown

Red

Orange

Orange

Blu

Brn

Red

Org

Org

+12Vdc

-12Vdc

+5Vdc

+24Vdc

+12Vdc (4/330)

Adapter Harness

Adapter Harness 811-9015-01 connects non-TUV approved fastons on AC and DC wire harnesses to

TUV approved fastons that were cut into production in February 1987. One end of the adapter harness has TUV approved female fastons. The other end of the adapter harness has non-TUV male fastons.

A TUV female faston attaches to a non-TUV male faston.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ea.htm (1 von 2) [25.04.2002 16:00:00]

II: Power - Wire Harnesses

A non-TUV female faston does not attach to a TUV male faston. Use adapter harness 811-9015-01.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ea.htm (2 von 2) [25.04.2002 16:00:00]

II: Power - Sun 5-Slot Office Pedestal Wiring Diagram

Sun 5-Slot Office Pedestal Wiring Diagram

Sun-4/330 and SPARCserver 630MP


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006eb.htm [25.04.2002 16:00:03]


Sun 12-Slot Office Pedestal Wiring Diagram

Sun-3/470, Sun-4/370, and Sun-4/470 shipped prior to

August 1991

Sun-4/470 and SPARCserver 670MP shipped after August

1991 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ec.htm (1 von 2) [25.04.2002 16:00:18]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ec.htm (2 von 2) [25.04.2002 16:00:18]

II: Power - Sun 16-Slot Logic Enclosure Wiring Diagram

Sun 16-Slot Logic Enclosure Wiring

Diagram

Sun-4/390 shipped prior to April 1990

Sun-4/390, Sun-4/490, and SPARCserver 690MP shipped after April 1990 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ed.htm (1 von 2) [25.04.2002 16:00:30]

II: Power - Sun 16-Slot Logic Enclosure Wiring Diagram


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ed.htm (2 von 2) [25.04.2002 16:00:30]

Sun4/II: Trouble - Diagnostics - Contents

Diagnostics

Self-Test Diagnostic

Diagnostic Executive

1.2 Diagnostic Executive (Sun-4)

1.2 Diagnostic Executive (Sun-4s)

1.6 Diagnostic Executive (Sun-4c)

Sun Diagnostics 3.2

Loopback Connectors


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004e7.htm [25.04.2002 16:00:33]

Sun4/II: Trouble - Diagnostics - Self-Test Diagnostic

Self-Test Diagnostic

The CPU Self-Test runs in either the Normal or Diag mode. Set the CPU DIAG/NORM switch to

DIAG or set the diag-switch? NVRAM parameter to true to enable the Diag mode.

In the Normal mode, the CPU runs through a basic set of tests and reports errors on the diagnostic

LEDs. Refer to the appropriate Field Service Manual and the Troubleshooting Section of this

Handbook for self-test LED error code information.

When the CPU is set to the Diag mode, the self-tests are more extensive than in the Normal mode and include a complete memory check. Connect an ASCII terminal to port A to display the self-test output when the system is in Diag mode. Use full duplex, 9600 baud, XON/XOFF, 8bits/1 stop bit, and no parity with a null modem type cable.

On Sun-4 systems, enter "x" at the PROM Monitor prompt to display the Extended Diagnostics menu.

At the prompt select a test for execution. To return to the PROM Monitor, enter "q".

Some tests were removed from the 2.8 EPROM in November 1988 to make room for more boot and display device drivers. With the 2.8 EPROM, boot path tests are executed directly from the PROM

Monitor prompt using the command:

>b*device()

On systems with the Open Boot PROM, use the help command to display a list and description of available tests.

ok help diag


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0070d.htm [25.04.2002 16:00:35]

Sun4/II: Trouble - Diagnostics - Diagnostic Executive

Diagnostic Executive

The Diagnostic Executive (Exec) provides a single, unified diagnostic environment with one user interface. The diagnostic tests reside in individual programs that work through the Exec platform. The platform provides a consistent interface and multitasking capabilities. Some features are:

Multiple Consoles

The Exec can run from any control terminal. This may be a monitor, serial port, or a remote console.

Error Logging

The Exec provides the ability to capture error messages into a logfile. The logfile may reside on a local disk or on a server.

Script Execution

Command scripts can be used to drive the menus without further user input.

Remote Execution

The Exec has the ability to perform remote diagnostics over a modem connected to a Serial Port or over Ethernet.

Due to the complexity of the Exec, individual tests will not be discussed here. Refer to the Sun

Diagnostic Executive User Manuals for additional information. Tables of Contents for the Exec are included in this section.

Loopback connectors are required for some tests. The loopback connectors are described at the end of this section.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0070e.htm [25.04.2002 16:00:39]

Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive

1.2 Diagnostic Executive

Sun-4

Table of Contents

NAME tpboot.sun4

Copyright toc extract_exec

Copyright exec4 diags4 cg6.4exec

cg8.4.exec

cg9.4.exec

color4.exec

cpcache4.exec

cpu4.exe

eeptool4.exec

ether4.exec

FILE

(DECIMAL)

0

DESCRIPTION

Enables boot from tape

3

4

1

2

Textfile containing copyright notice

Contains list of contents of tape

Script to copy diagnostics to disk


9

10

11

12

7

8

5

6

Diag Exec for Sun-4 architecture

Diagnostic Menu and File names

P4 Low-Eng Graphics Accelerator

P4 24-Bit Frame Buffer Board Diagnostic

VME 24-Bit Frame Buffer Board Diagnostic

Generic VME Color Board Diagnostic

4300 CPU Cache Diagnostic

CPU Board Diagnostic ether2.4.exec

exectest4.exec

fddi4.exec

fpu4.exec

gp1.4.exec

gp2.4.exec

hsi4.exec

ipi4.exec

17

18

19

20

13

14

15

16

EEPROM programming tool

Ethernet Diagnostic

2nd Ethernet Diagnostic

Exec Verification Suite

FDDI Board Diagnostic

Floating Point Unit Diagnostic

Graphics Processor1/Graphics Buffer Diag

Graphics Processor2 Diagnostic kb4.exec

mcp4.exec

mem4.exec

mouse4.exec

mti4.exec

scsisub4.exec

espscsi.exec

smd4.exec

taac4.exec

25

26

27

28

21

22

23

24

29

30

31

High Speed Serial Board Diagnostic

IPI Disk Subsystem Diagnostic

Sun Keyboard Diagnostic

Sun ALM2/MCP Board Diagnostic

Sun Memory Diagnostic

Sun Mouse Diagnostic

Sun MTI/ALM Board Diagnostic

Sun SCSI Subsystem Diagnostic

4300 Extended SCSI Diagnostic

Sun SMD Diagnostic

TAAC-1 Diagnostic http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0070f.htm (1 von 2) [25.04.2002 16:00:48]

Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive tape4.exec

video4.exec

vidmon4.exec

32

33

34

Pertec 1/2-inch Tape Diagnostic

Sun Video Circuit Diagnostic

Sun Video Monitor Diagnostic vme4.exec

netcon4

35

36

Sun VME Diagnostic

Network Console Program logfile 37 Error Log File eccmem4.diag

38 (0x27) Standalone ECC Memory Diagnostic cache4.diag

Copyright

39 (0x28) Standalone Cache Memory Diagnostic

40 Textfile containing copyright notice



Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive - Sun-4s

1.2 Diagnostic Executive - Sun-4s

SPARCsystems 300/400

Table of Contents cg6.4exec

cg8.4.exec

cg9.4.exec

color4.exec

eeptool4.exec

espscsi.exec

ether2.4.exec

ether4.exec

exectest4.exec

fddi4.exec

fpu4.exec

gpl.4.exec

gp2.4.exec

hsi4.exec

ipi4.exec

mcp4.exec

mti4.exec

scsisub4.exec

NAME tpboot.sun4

Copyright toc extract_exec

Copyright exec4 diags4

FILE DESCRIPTION

0 Enables boot from tape


2 Contains list of contents of tape

3 Script to copy diagnostics to disk


5 Diag Exec for Sun-4s architecture

6 Diagnostic Menu and File names cpu4.exe

mem4.exec

7 CPU Board Diagnostic

8 Memory Diagnostic cpcache4_300.exec

9 4300 Cache Diagnostic cpcache4_400.exec

10 4400 Cache Diagnostic iocache4.exec

video4.exec

kb4.exec

mouse4.exec

11

12

13

14

4400 I/O Cache Diagnostic

Video Circuit Diagnostic

Keyboard Diagnostic

Mouse Diagnostic

15

16

17

18

19

20

21

22

23

24

25

26

27

28

29

30

31

32

P4 Low-Eng Graphics Accelerator

P4 24-Bit Frame Buffer Board Diagnostic

VME 24-Bit Frame Buffer Board Diagnostic

Generic VME Color Board Diagnostic

EEPROM programming tool

4300 CPU Extended SCSI Diagnostic

Ethernet II Board Diagnostic

Sun Ethernet Diagnostic

Exec Verification Suite

FDDI Board Diagnostic

Floating Point Diagnostic

Graphics Processor1/Graphics Buffer Diag

Graphics Processor2 Diagnostic

High Speed Serial Board Diagnostic

IPI Disk Subsystem Diagnostic

Sun ALM2/MCP Board Diagnostic

Sun MTI/ALM Board Diagnostic

Sun SCSI Subsystem Diagnostic http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00710.htm (1 von 2) [25.04.2002 16:00:53]

Sun4/II: Trouble - Diagnostics - 1.2 Diagnostic Executive - Sun-4s smd4.exec

taac4.exec

tape4.exec

vme4.exec

netcon4 logfile eccmem4.diag

cache4.diag

Copyright

33

41

Sun SMD Diagnostic

34 TAAC Diagnostic

35 Tape Diagnostic

36 VME Diagnostic

37 NETCON

38 LOGFILE

39 ECC Memory Diagnostic

40 Cache Diagnostic


Reference

SunDiagnostic Executive User's Guide Addenda, 800-3493-10.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00710.htm (2 von 2) [25.04.2002 16:00:53]

Sun4/II: Trouble - Diagnostics - 1.6 Diagnostic Executive

1.6 Diagnostic Executive

Sun-4c

Table of Contents

NAME exec4c

DESCRIPTION

Diag Exec for Sun-4c architecture diags4c Diagnostic Menu and File names cache4c.exec

Cache Memory Diagnostic cpu4c.exec

CPU Board Diagnostic bantam4c.exec SBus FDDI Diagnostic codec4c.exec

SBus ISDN Diagnostic dbri4c.exec

SBus ISDN Diagnostic ether4c.exec

Ethernet II Board Diagnostic fdc4c.exec

Floppy Disk Controller Diagnostic fpu4c.exec

Floating Point Unit Diagnostic kbm4c.exec

Keyboard Diagnostic mem4c.exec

Memory Diagnostic scsi4c.exec

SCSI Subsystem Diagnostic cg6.4c.exec

CG6 Diagnostic video4c.exec

Video Diagnostic spif4c.exec

Serial Parallel Controller Diagnostic bipro4c.exec

SPARCprinter Board Diagnostic sunpc4c.exec

SunPC Board Diagnostic vfc4c.exec

Video Frame Capture Diagnostic hsis4c.exec

HSI/S Diagnostic token4c.exec

Token Ring Diagnostic cg12.4c.exec

CG12 Video Diagnostic n/a TAR image of executables n/a TAR image of Development Platform

Notes

1. The 1.6 Diagnostic Executive supports the Sun-4/20, Sun-4/25, Sun-4/40, Sun-4/50, Sun-4/60,

Sun-4/65, and Sun-4/75.

2. The 1.6 Diagnostic Executive supports the Sun-4/15, Sun-4/30, and SPARCstation 10.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00711.htm [25.04.2002 16:00:55]

Sun4/II: Trouble - Diagnostics - Sun Diagnostics 3.2

Sun Diagnostics 3.2

Featuring: MPDiag and SunDiagnostic Executive 2.2

SS600MP / SS10 / SS1000 /SC2000

MPDiag tests the following components and functions:

Audio

Ethernet

FPU

Interrupts and Traps

MBus Module

Memory

MMU/IOMMU

MP Cache

MP Memory

Serial Ports

SunDiagnostic Executive 2.2 includes the following tests:

CPU Diagnostic

CG6 Frame Buffer Diagnostic

EEPROM Editing Tool

Ethernet Diagnostic

Floating Point Unit Diagnostic

Keyboard Diagnostic

IPI Diagnostic

MCP Diagnostic

Memory Diagnostic

Mouse Diagnostic

Prestoserve Diagnostic

SCSI Diagnostic

SBus TRI/S Diagnostic

SBus HSI/S Diagnostic

SBus FDDI/S Diagnostic

SBus SPC/S Diagnostic

SBus SPARCprinter Diagnostic

Video Frame Buffer Diagnostic http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00712.htm (1 von 2) [25.04.2002 16:00:56]

Sun4/II: Trouble - Diagnostics - Sun Diagnostics 3.2

Notes

1. Sun Diagnostics 3.2 was released in July 1993.

2. This is the last field release of the SunDiagnostic Executive.



Sun4/II: Trouble - Diagnostics - Loopback Connectors

Loopback Connectors

RS-232/RS-423

PART # SYSTEM BOARDS CONNECT PINS

540-1281-01 CPU,SCSI, and ALM 2-3 4-5 6-20

540-1558-01 CPU, SCSI, ALM, ALM-2,

MCP, and SPC/S

2-3 4-5 6-8-20

17-24

RS-449


540-1559-01 MCP 4-6 7-9 8-17 22-24

25-27 11-12-13

29-30-31 35-26

Parallel Port


540-1560-01

501-1196-01

ALM-2

IPC

1-10

12-2-4-6-8

13-3-5-7-9

5-15 6-13 7-12

8-10 9-11

SBus Printer Board


530-1683-01 Parallel Port to Video Port Loopback Cable

SBus High Speed Serial Interface (HSI/S)


370-1381-01

530-1430-01

96-Pin High-Density Loopback Connector

RS-449 Loopback Test Plug

SBus Serial Parallel Controller (SPC)

PART # DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00713.htm (1 von 2) [25.04.2002 16:00:58]

Sun4/II: Trouble - Diagnostics - Loopback Connectors

370-1366-01

540-1558-01

96-Pin High-Density Loopback Connector

RS-232/RS-423 Loopback Test Plug



Sun4/II: Trouble - Disk - Contents

Disk

SunOS 4.x SCSI Targets

Solaris 2.1 and 2.2 SCSI Targets

Solaris 2.3 SCSI Targets

SCSI Disk Drives

Single-ended 8-bit SCSI Pinouts

Media Defect Management

SCSI Option Bit

SCSI Sense Keys

SCSI Sense Codes

IPI Disk Drive

1.3GB IPI Physical and Logical Geometry

IPI Disk Controller

ISP-80 Disk Controller



Sun4/II: Trouble - Disk - SunOS 4.x SCSI Targets

SunOS 4.x SCSI Targets

Sun-4/330 on SunOS 4.x

SCSI DEVICE TARGET ID UNIX ID BOOT ID

1st Internal Disk 3 sd6 sd(0,18,0)

2nd Internal Disk

1st Internal Tape

1

4 sd2 st0 sd(0,8,0) st(0,0,0)

1st External Tape

2nd External Tape

CD-ROM

4

5

6 st0 st1 sr0 st(0,0,0) st(0,28,0) st(0,30,1)

Sun-4/370/470 and Sun-3/470 on SunOS 4.x

SCSI DEVICE TARGET ID UNIX ID BOOT ID

1st Internal Disk 0 sd0 sd(0,0,0)

2nd Internal Disk

3rd Internal Disk

1

2 sd2 sd4 sd(0,8,0) sd(0,10,0)

4th Internal Disk

1st Internal Tape

2nd Internal Tape

CD-ROM

3

4

5

6 sd6 st0 st1 sr0* sd(0,18,0) st(0,0,0) st(0,28,0) st(0,30,1)

* The Sun 4300 CPU requires EPROM 3.0.2 to boot from CD-ROM.

The Sun 4400 CPU requires EPROM 3.0 to boot from CD-ROM

Sun-4/390/490 on SunOS 4.0.3

SCSI DEVICE HOST ADAPTER TARGET ID UNIX ID BOOT ID

1st Tape

2nd Tape

CD-ROM

1st Tape

2nd Tape

1st SCSI

1st SCSI

1st SCSI

2nd SCSI

2nd SCSI

4

5

6

4

5 st0 st1 sr0* st2 st3 st(0,0,0) st(0,28,0) st(0,30,1) st(1,0,0) st(1,28,0)


The Sun 4400 CPU requires EPROM 3.0 to boot from CD-ROM

Sun-4/390/490 on SunOS 4.1 PSR A

SCSI DEVICE HOST ADAPTER TARGET ID UNIX ID BOOT ID http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00714.htm (1 von 2) [25.04.2002 16:01:12]

Sun4/II: Trouble - Disk - SunOS 4.x SCSI Targets

1st Tape

2nd Tape

3rd Tape

4th Tape

CD-ROM

1st Tape

2nd Tape

3rd Tape

4th Tape

1st SCSI

1st SCSI

1st SCSI

1st SCSI

1st SCSI

2nd SCSI

2nd SCSI

2nd SCSI

2nd SCSI

4

5

3

2

6

4

5

3

2 st0 st1 st2 st3 sr0* st2 st3 st6 st7


The Sun 4400 CPU requires EPROM 3.0 to boot from CD-ROM st(0,0,0) st(0,28,0) st(0,18,0) st(0,10,0) st(0,30,1) st(1,0,0) st(1,28,0) st(1,18,0) st(1,10,0)



Sun4/II: Trouble - Disk - Solaris 2.1 and 2.2 SCSI Targets

Solaris 2.1 and 2.2 SCSI Targets

Solaris 2.1 and 2.2 allow any SCSI device to be assigned any Target number. This chart shows the default target numbers for sd and st devices that are symbolic links from /dev (SunOS 4.x) to

/devices (Solaris 2.x).

26

27

28

29

22

23

24

25

30

31

32

18

19

20

21

14

15

16

17

SCSI HOST

0

1

4

5

2

3

10

11

12

13

8

9

6

7

98 - 101

105 - 108

112 - 115

119 - 122

126 - 129

133 - 136

140 - 143

147 - 150

154 - 157

161 - 164

168 - 171

175 - 178

182 - 185

189 - 192

196 - 199

203 - 206

210 - 213

217 - 220

224 - 227

DIFFERENTIAL SCSI DISK DRIVE

DISK DRIVE TAPE DRIVE

0 - 3

7 - 10

4 - 5

11 - 12

14 - 17

21 - 24

28 - 31

35 - 38

18 - 19

25 - 26

32 - 33

39 - 40

42 - 45

49 - 52

56 - 59

63 - 66

70 - 73

77 - 80

84 - 87

91 - 94

46 - 47

53 - 54

60 - 61

67 - 68

74 - 75

81 - 82

88 - 89

95 - 96

102 - 103

109 - 110

116 - 117

123 - 124

130 - 131

137 - 138

144 - 145

151 - 152

158 - 159

165 - 166

172 - 173

179 - 180

186 - 187

193 - 194

200 - 201

207 - 208

214 - 215

221 - 222

228 - 229

160

167

174

181

188

195

202

209

104

111

118

125

132

139

146

153

216

223

230

76

83

90

97

48

55

62

69

CD-ROM

6

13

20

27

34

41 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00715.htm (1 von 2) [25.04.2002 16:01:15]

Sun4/II: Trouble - Disk - Solaris 2.1 and 2.2 SCSI Targets

36

37

38

39

33

34

35

231 - 234

238 - 241

245 - 248

252 - 255

259 - 262

266 - 269

273 - 276

235 - 236

242 - 243

249 - 250

256 - 257

263 - 264

270 - 271

277 - 278


Comments and Suggestions

237

244

251

258

265

272


Sun4/II: Trouble - Disk - Solaris 2.3 SCSI Targets

Solaris 2.3 SCSI Targets

Solaris 2.3 allows any SCSI device to be assigned any Target number. This chart shows the default target numbers for sd and st devices that are symbolic links from /dev (SunOS 4.x) to /devices

(Solaris 2.x).

24

25

26

27

20

21

22

23

28

29

30

31

32

16

17

18

19

12

13

14

15

WIDE SCSI DISK DRIVE

SCSI HOST DISK DRIVE TAPE DRIVE CD-ROM

2

3

0

1

0 - 14

15 - 29

30 - 44

45 - 59

4 - 5

19 - 20

34 - 35

49 - 50

14

21

36

51

8

9

10

11

6

7

4

5

60 - 74

75 - 89

90 - 104

105 - 119

120 - 134

135 - 149

150 - 164

165 - 179

64 - 65

79 - 80

94 - 95

109 - 110

124 - 125

139 - 140

154 - 155

169 - 170

66

81

96

111

126

141

156

171

180 - 194

195 - 209

210 - 224

225 - 239

240 - 254

255 - 269

270 - 284

285 - 299

300 - 314

315 - 329

330 - 344

345 - 359

360 - 374

375 - 389

390 - 404

405 - 419

420 - 434

435 - 449

450 - 464

465 - 479

480 - 494

184 - 185

199 - 200

214 - 215

229 - 230

244 - 245

259 - 260

274 - 275

289 - 290

304 - 305

319 - 320

334 - 335

349 - 350

364 - 365

379 - 380

394 - 395

409 - 410

424 - 425

439 - 440

454 - 455

469 - 470

484 - 485

306

321

336

351

366

381

396

411

426

441

456

471

486

186

201

216

231

246

261

276


Sun4/II: Trouble - Disk - Solaris 2.3 SCSI Targets

36

37

38

39

33

34

35

495 - 509

510 - 524

525 - 539

540 - 554

555 - 569

570 - 584

585 - 599

499 - 500

514 - 515

529 - 530

544 - 545

559 - 560

574 - 575

589 - 590


Comments and Suggestions

501

516

531

546

561

576


Sun4/II: Trouble - Disk - Single-ended 8-bit SCSI Pinouts

Single-ended 8-bit SCSI Pinouts

-ATN

GND

BSY

-ACK

-RST

-MSG

-SEL

-C/D

-REQ

-I/O

SIGNAL DD-50P HD-50 DD-50SA HD-68 SIGNAL DD-50P HD-50 DD-50SA HD-68

-DB(0) 2 26 34 40 GND 1 1 1 6

-DB(1)

-DB(2)

4

6

27

28

2

19

41

42

GND

GND

3

5

2

3

18

35

7

8

-DB(3) 8

-DB(4) 10

-DB(5) 12

-DB(6) 14

29

30

31

32

36

4

21

38

43

44

45

46

GND

GND

GND

GND

7

9

11

13

4

5

6

7

3

20

37

5

9

10

11

12

-DB(7) 16

-DB(P) 18

GND

GND

20

22

GND

TPWR

GND

GND

33

34

35

36

6

23

40

8

47

48

49

50

24 37 Res 25 51 Opn

26 38 42 52

28 39 Res 10

30 40 27

53

54

GND

GND

GND

GND

GND

GND

GND

GND

15

17

19

21

29

8

9

10

11

25 13 Opn

15

22

39

7

24

9

27 14 Res 26

43

13

14

15

16

23 12 Res 41 17 Opn

18 Opn

19

20

40

42

44

46

32

34

36

38

48

50

45

46

47

48

41

42

43

44

49

50

14

31

48

16

44

12

29

46

33

50

59

60

61

62

55

56

57

58

63

64

GND

GND

GND

GND

GND

GND

GND

GND

GND

GND

39

41

43

45

31

33

35

37

47

49

20

21

22

23

16

17

18

19

24

25

30

47

15

32

11

28

45

13

49

17

25

26

27

28

21

22

23

24

29

30

Connector Types http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00719.htm (1 von 2) [25.04.2002 16:01:32]

Sun4/II: Trouble - Disk - Single-ended 8-bit SCSI Pinouts

Notes

1. On HD50 cables, Pins 12, 14, 37, and 39 are reserved and Pin 13 is open.

2. On HD50 to HD68 cables, Pins 1, 2, 3, 4, 5, 17, 18, 31, 32, 33, 34, 35, 36, 37, 38, 39, 51, 65,

66, 67, and 68 are open.



Sun4/II: Trouble - Disk - Media Defect Management

Media Defect Management

Embedded SCSI Disk Drives

The FORMAT UNIT command formats the media so that all data blocks can be accessed. The following lists are used during the defect management process.

Primary, or Manufacturer's, Defect List (P list)

The P list supplied by the manufacturer is resident on the disk drive. The initiator can reference this list with the READ DEFECT DATA command. The initiator cannot change or erase the Primary list.

Certification Defect List (C list)

The C list is the position information of defective data blocks detected during data block verification after initialization when the FORMAT UNIT command is issued. These defects are added to the

Grown list.

Data Defect List (D list)

The D list is the defect position information transferred from the initiator upon execution of the

FORMAT UNIT command. These defects are added to the Grown list.

Grown Defect List (G list)

The G list includes defects identified to, or by, the drive. It does not include the P list. These defects are classified as flaws appearing after the media is formatted. The initiator may request that the current G list be used during formatting, or that the current G list be erased and a new list begun.

Entries to the G list include:

1. Defects provided to the drive in D lists during previous FORMAT UNIT commands.

2. Drive C list defects detected during previous FORMAT UNIT commands.

3. Defects appended by successful completion of the REASSIGN BLOCKS command.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071a.htm [25.04.2002 16:01:33]

Sun4/II: Trouble - Disk - SCSI Option Bit

SCSI Option Bit

SCSI Option Bit Setting

Use the following procedure to determine the SCSI option bit setting under Solaris 2.x:

# adb -k /kernel/unix /dev/mem (Solaris 2.0 - 2.4)

# adb -k /dev/ksyms /dev/mem (Solaris 2.5) scsi_options/X

$q

SCSI Option Bits

Disconnect/Reconnect 0x008

Linked Commands 0x010

Synchronous Transfer 0x020

Parity 0x040

Tagged Queuing

Fast SCSI

Wide SCSI

Fast 20

0x080

0x100

0x200

0x400

Tagged Queuing

Tagged Queuing allows a disk to receive more than one command at a time and to perform the commands in an order that reduces disk latency in many applications. Tagged Queuing is implemented in Solaris 2.1.

Some SCSI disk drives may not properly implement Tagged Queuing. Disable Tagged Queuing in the driver to prevent unrecoverable failures. Add the following to the /etc/system file under Solaris 2.x: set scsi_options=0x178

Wide SCSI

To enable Wide SCSI under Solaris 2.3, add the following to the /etc/system file: set scsi_options=0x3f8


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071b.htm [25.04.2002 16:01:38]

Sun4/II: Trouble - Disk - SCSI Sense Keys

SCSI Sense Keys

KEY DESCRIPTION

0 NO SENSE

There is no specific sense key information to be reported for the designated logical unit. This would be the case for a successful command or a command that received CHECK

CONDITION or COMMAND TERMINATED status because one of the filemark, EOM, or

ILI bits is set to one.

1 RECOVERED DATA

The last command completed successfully with some recovery action performed by the target.

Details may be determined by examining the additional sense bytes and the information field.

2 NOT READY

The logical unit addressed cannot be accessed. Operator intervention may be required to correct this condition.

3 MEDIUM ERROR

The command terminated with a non-recovered error condition that was probably caused by a flaw in the medium or an error in the recorded data. This sense key may also be returned if the target is unable to distinguish between a flaw in the medium and a specific hardware failure

(sense key 4).

4 HARDWARE ERROR

The target detected a non-recoverable hardware failure while performing the command or during self test.

5 ILLEGAL REQUEST

There was an illegal parameter in the command descriptor block or in the additional parameters supplied as data for some commands. If the target detects an invalid parameter in the command descriptor block, then it shall terminate the command without altering the medium. If the target detects an invalid parameter in the additional parameters supplied as data, then the target may have already altered the medium. This sense key may also indicate that an invalid IDENTIFY message was received.

6 UNIT ATTENTION

The removable medium may have been changed or the target has been reset.

7 DATA PROTECT

A command that reads or writes the medium was attempted on a block that is protected from this operation.

8 BLANK CHECK

A write-once device or a sequential-access device encountered blank medium or format-defined end-of-data indication while reading or a write-once device encountered.

9 Vendor Specific

This key is available for reporting vendor specific conditions.

a COPY ABORTED

A COPY, COMPARE, or COPY AND VERIFY command was aborted due to an error condition on the source device, the destination device, or both.

b ABORTED COMMAND

The target aborted the command. The initiator may be able to recover by trying the command again.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071c.htm (1 von 2) [25.04.2002 16:01:41]

Sun4/II: Trouble - Disk - SCSI Sense Keys c HARDWARE ERROR

The target detected a non-recoverable hardware failure while performing the command or during self test.

d VOLUME OVERFLOW

A buffered peripheral device has reached the end-of-partition and data may remain in the buffer that has not been written to the medium.

e MISCOMPARE

The source data did not match the data read from the medium.

f Reserved


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071c.htm (2 von 2) [25.04.2002 16:01:41]

Sun4/II: Trouble - Disk - SCSI Sense Codes

SCSI Sense Codes

BYTE

12

-

-

13

DESCRIPTION

Additional Sense Code (ASC)

Additional Sense Code Qualifier (ASCQ)

00 00 No additional sense information

00 01 Filemark detected

00 02 End of partition/medium detected

00 03 Setmark detected

00 04 Begining-of-Partition/Medium detected

00 05 End of data detected

00 11 Audio play operation in progress

00 12 Audio play operation paused

00 13 Audio play operation successfully completed

00 14 Audio play operation stopped due to error

00 15 No current audio status to return

01 00 No index/sector signal

02 00 No seek complete

03 00 Peripheral device write fault

03 01 No write current

03 02 Excessive write errors

04 00 Logical unit not ready, cause not reportable

04 01 Logical unit is in progress of becoming ready

04 02 Logical unit not ready, initiating command required

04 03 Logical unit not ready, manual intervention required

04 04 Logical unit not ready, format in progress

05 00 Logical unit does not respond to selection

06 00 No reference position found

07 00 Multiple peripheral devices selected

08 00 Logical unit communication failure

08 01 Logical unit communication time out

08 02 Logical unit communication parity error

09 00 Track following error

09 01 Tracking servo failure

09 02 Focus servo failure

09 03 Spindle servo failure

0a 00 Error log overflow

0c 00 Write error

0c 01 Write error recovered with auto reallocation

0c 02 Write error - auto reallocation failed http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071d.htm (1 von 5) [25.04.2002 16:01:52]


10 00 ID CRC or ECC error

11 00 Unrecovered read error

11 01 Read retries exhausted

11 02 Error log too long to correct

11 03 Multiple read errors

11 04 Unrecovered read error - auto reallocate failed

11 05 L-EC uncorrectable error

11 06 CIRC unrecovered error

11 07 Data resynchronization error

11 08 Incomplete block read

11 09 No gap found

11 0a Miscorrected error

12 00 Address mark not found for ID field

13 00 Address mark not found for data field

14 00 Recorded entity not found

14 01 Record not found

15 00 Random positioning error

15 01 Mechanical positioning error

15 02 Positioning error detected by read of medium

16 00 Data synchronization mark error

17 00 Recovered data with no error correction applied

17 01 Recovered data with retries

17 02 Recovered data with positive head offset

17 03 Recovered data with negative head offset

17 04 Recovered data with retries and/or CIRC applied

17 05 Recovered data using previous sector

17 06 Recovered data without ECC - Data auto-reallocated

18 00 Recovered data with error correction applied

18 01 Recovered data with error correction & retries applied

18 02 Recovered data with ECC and/or retries

18 03 Recovered data with CIRC

18 04 Recovered data with LEC

19 00 Defect list error

19 01 Defect list not available

19 02 Defect list error in primary list

19 03 Defect list error in grown list

1a 00 Parameter list length error

1b 00 Synchronous data transfer error

1c 00 Defect list not found

1c 01 Primary defect list not found

1c 02 Grown defect list not found http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071d.htm (2 von 5) [25.04.2002 16:01:52]


1d 00 Miscompare during verify operation

1e 00 Recovered ID with ECC correction

20 00 Invalid command operation code

21 00 Logical block address out of range

21 01 Invalid element address

22 00 Illegal function for device type

24 00 Invalid field in CDB

25 00 Logical unit not supported

26 00 Invalid field in parameter list

26 01 Parameter not supported

26 02 Parameter value invalid

26 03 Threshold parameters not supported

27 00 Write protected

28 00 Not ready to ready transition

28 01 Import / Export element accessed

29 00 Power-On, reset, or bus device reset occurred

2a 00 Parameters changed

2a 01 Mode parameters changed

2a 02 Log parameters changed

2b 00 Copy cannot execute since host cannot disconnect

2c 00 Command sequence error

2c 01 Too many windows specified

2c 02 Invalid combination of windows specified

2d 00 Overwrite error on update in place

2f 00 Commands cleared by another initiator

30 00 Incompatible medium installed

30 01 Cannot read medium - unknown format

30 02 Cannot read medium - incompatible format

30 03 Cleaning cartridge installed

31 00 Medium format corrupted

31 01 Format command failure

32 00 No defect spare location available

32 01 Defect list update failure

33 00 Tape length error

36 00 Ribbon/Ink/Toner faliure

37 00 Rounded parameter

39 00 Saving parameters not supported

3a 00 Medium not present

3b 00 Sequential positioning error

3b 01 Tape position error at begining of medium

3b 02 Tape position error at end of medium http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071d.htm (3 von 5) [25.04.2002 16:01:52]


3b 03 Tape or electronic vertical forms unit not ready

3b 04 Slew failure

3b 05 Paper jam

3b 06 Failed to sense top of form

3b 07 Failed to sense bottom of form

3b 08 Reposition error

3b 09 Read past end of medium

3b 0a Read past begining of medium

3b 0b Position past end of medium

3b 0c Position past begining of medium

3b 0d Medium destination element full

3b 0e Medium source element empty

3d 00 Invalid bits in identify message

3e 00 Logical unit has not self configured yet

3f 00 Target operating conditions have changed

3f 01 Microcode has been changed

3f 02 Changed operating definition

3f 03 Inquiry data has changed

40 nn Diagnostic failure on component nn (80h-ffh)

41 00 Data path failure

42 00 Power-On or Self-Test failure

43 00 Message error

44 00 Internal target failure

45 00 Select/Reselect failure

46 00 Unsuccessful soft reset

47 00 SCSI parity error

48 00 Initiator detected error message received

49 00 Invalid message error

4a 00 Command phase error

4b 00 Data phase error

4c 00 Logical unit failed self configuration

4e 00 Overlapped commands attempted

50 00 Write append error

50 01 Write append position error

50 02 Position error related to timing

51 00 Erase failure

52 00 Cartridge fault

53 00 Media load/eject failed

53 01 Unload tape failure

53 02 Medium removal prevented

54 00 SCSI to host system interface failure http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071d.htm (4 von 5) [25.04.2002 16:01:52]


55 00 System resource failure

57 00 Unable to recover table-of-contents

58 00 Generation does not exist

59 00 Updated block read

5a 00 Operator request or state change input

5a 01 Operator medium removal request

5a 02 Operator selected write protect

5a 03 Operator selected write permit

5b 00 Log exception

5b 01 Threshold condition met

5b 02 Log counter at maximum

5b 03 Log list codes exhausted

5c 00 RPL status change

5c 01 Spindles synchronized

5c 02 Spindles not synchronized

60 00 Lamp failure

61 01 Unable to acquire video

61 02 Out of focus

62 00 Scan head positioning error

63 00 End of user area encountered on this track

64 00 Illegal mode for this track

80 80 Vendor unique ASC and ASCQ through ff ff Vendor unique ASC and ASCQ



Sun4/II: Trouble - Disk - 1.3GB IPI Disk Drive

1.3GB IPI Disk Drive

Physical and Logical Geometry

The 1.3GB IPI Disk Drive uses Zone Bit Recording (ZBR). The outer tracks have a higher bit density than the inner tracks.

The defect list for the 1.3GB IPI Disk Drive is in physical block number. Errors reported under the operating system format utility are in logical block number. Block numbers converted to cylinder/head/sector by the show command, are in logical block number.

The analyze command performs the conversion from logical to physical block when a defect is detected.

The repair command does not perform the conversion from a logical block number to a physical block number. Do not enter the logical block when using the repair command.

To add a defect to the defect list, first convert the logical block number to a physical block number.

Then, use the add command to enter the physical block number into the defect list. Do not enter the logical block number when using the add command.

Use the Disk Drive Logical Geometry chart to find Zone, First Block in Zone, First Cylinder in Zone,

Cylinder Size of Zone, and Track Size of Zone.

Example: error reported on block 1000000.

LBN = 1000000

Zone = 2

First Block in Zone 2 = 929526

First Cylinder in Zone 2 = 701

Cylinder Size of Zone 2 = 1292

Track Size of Zone 2 = 76

1.3GB IPI Disk Drive Logical Geometry

ZONE

FIRST

CYL

LAST

CYL

FIRST

BLOCK

0 0 625 0

FIRST

C/H/S

0/0/0

LAST

BLOCK

LAST

C/H/S

TRK

SIZE

CYL

SIZE

830075 625/16/77 78 1326

1 626 700 830076 626/0/0 929525 700/16/77 78 1326

2 701 800 929526 701/0/0 1058725 798/7/31 76 1292

3 801 925 1058726 798/7/32 1215975 917/0/33 74 1258

4 926 1050 1215976 917/0/34 1368975 1032/6/75 72 1224

5 1051 1175 1368976 1032/6/76 1521975 1147/13/39 72 1224

6 1176 1300 1521976 1147/13/40 1670725 1259/16/43 70 1190

7 1301 1400 1670726 1259/16/44 1786325 1347/2/47 68 1156

8 1401 1500 1786326 1347/2/48 1898525 1431/13/5 66 1122

9 1501 1600 1898526 1431/13/6 2007325 1513/13/73 64 1088 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071e.htm (1 von 4) [25.04.2002 16:02:00]


10 1601 1800 2007326 1513/13/74 2218125 1672/13/39 62 1054

11 1801 1900 2218126 1672/13/40 2320125 1749/12/15 60 1020

12 1901 2000 2320126 1749/12/16 2418725 1824/1/23 58 986

13 2001 2100 2418726 1824/1/24 2512769 1894/16/77 58 986

1.3GB IPI Disk Drive Physical Geometry

ZONE

FIRST

CYL

LAST

CYL

BYTES /

TRACK

SECTORS

BYTES/

SECTORS

CDT 2

0 0 625 50399 40 1230 46

3

4

1

2

626

701

801

926

700

800

925

1050

49559

48719

47039

46199

40

39

38

37

1226

1225

1221

1220

45

44

43

42

5 1051 1175 45359

6 1176 1300 43679

7 1301 1400 42839

8 1401 1500 41159

9 1501 1600 40319

10 1601 1800 38639

11 1801 1900 37799

12 1901 2000 36959

13 2001 2100 36119

37

36

35

34

33

32

31

30

30

1219

1212

2111

1210

1206

1201

1201

1197

1196

37

35

35

34

33

41

40

39

38

Longhand Conversion of Physical to Logical

Block

LBN - First Block = LB

1000000 - 929526 = 70474

To find the Physical Cylinder

First Cylinder + (LB ÷ Cylinder Size in blocks) = Pcylinder

701 + (70474 ÷ 1292) = 755 (discard the remainder)

To find the Physical Head http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071e.htm (2 von 4) [25.04.2002 16:02:00]


To find the Physical Sector

The function of the Modulus Operator % is to give the remainder of the first value divided by the second value.

Calculator Conversion of Physical to Logical

Block

LBN - First Block = LB

1000000 - 929526 = 70474

To find the Physical Cylinder

First Cylinder + (LB ÷ Cylinder Size in blocks) = Pcylinder

701 + (70474 ÷ 1292) = Pcylinder

701 + (54.54644) = 755.54644

755 = Pcylinder (0.54644 = Pcylinder remainder) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071e.htm (3 von 4) [25.04.2002 16:02:00]


To find the Physical Head

(Pcylinder remainder × Cylinder size) ÷ Track Size = Phead

(0.54644 × 1292) ÷ 76 = Phead

(706.00048) ÷ 76 = 9.28948

9 = Phead (0.28948 = Phead remainder)

To find the Physical Sector

Phead remainder × Track Size = Psector

0.28948 × 76 = Psector

0.28948 × 76 = 22.00048

22 = Psector

Logical block 1000000 is located at physical cylinder 755, head 9, sector 22. Add the physical block number to the defect list.

The show command reports that logical block 1000000 is located at logical cylinder 754, head 2, sector 40. Do not add the logical block number to the defect list.



Sun4/II: Trouble - Disk - SP-80 Disk Controller (IPI-2)

ISP-80 Disk Controller

Self-Test Error Codes

LED 7 lights to indicate a failed self-test http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd0071f.htm (1 von 2) [25.04.2002 16:02:06]

Sun4/II: Trouble - Disk - SP-80 Disk Controller (IPI-2)

Diagnostic Engineering Monitor

The Diagnostic Engineering Monitor (DEMON) is entered when the Diag/Norm switch is in the Diag position.

POSITION SYSTEM ACTIVITY

DIAG Enters DEMON mode when Self-test is completed.

Self-test output is monitored by connecting the ISP-80 controller to a terminal set to 9600 baud, 8 data bits, no parity, and 1 stop bit. The ISP-80 Controller serial port is a 25-pin, dual in-line, header-type connector.

Since Sun does not make a cable that connects the ISP-80 controller and a terminal, use an adapter cable and a null modem cable.

Adapter Cable

Examples of Sun cables that can be used as adapter cables are:

530-1178-01 (ALM-1, RS-232)

530-1179-01 (ALM-1, RS-232)

530-1312-02 (ALM-2, Printer)

530-1313-01 (MCP, RS-232)

Sun SMD data cables cannot be used as the adapter cable because they do not have Pin 2.

Null Modem Cable

The null modem cable must have Pins 2 and 3 crossed and Pin-7 straight. Laserwriter Cable

530-1172-03 is an example of this type of cable.



Sun4/II: Troubleshooting - CPU - Contents

CPU

Sun-4 Architecture

Sun 4100

Sun 4200

Sun 4300

Sun 4300 Address Decoding

Sun 4400

Interrupt Levels

Sun-4 / Sun-4c / Sun-4m



Sun4/II: Troubleshooting - CPU - Sun 4100 Self-Test Error Codes

Sun 4100

Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ff.htm (1 von 2) [25.04.2002 16:02:14]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd006ff.htm (2 von 2) [25.04.2002 16:02:14]


Sun 4200

Self-Test Error Codes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00700.htm (1 von 2) [25.04.2002 16:02:21]





Sun 4300





Sun4/II: Troubleshooting - CPU - Sun 4300 Address Decoding

Sun 4300 Address Decoding

The physical address and the byte in error are used to determine a failing SIMM module. Socket locations are silkscreened on the component side of the CPU and 3U Memory Boards, and on the solder side of the 9U Memory Board. This section includes examples of errors and charts for the Sun

4300 CPU, 3U Memory Boards and 9U Memory Boards.

Error Examples

CPU Switch In NORM Position

Parity Error detected on byte 0

(Physical address 0x01000000) with PC 0xFFE90048

Parity Error detected on byte 2

The location of the failing SIMM module is U1702.

CPU Switch In DIAG Position error: at 0x000FFF8, expect 0x5A972C5a, obs 0x5AFE2C5 (looping)

Physical Address: 0x010FFFF8

(3U expansion memory) Expansion board #1 SIMM in Error: U0802

(9U expansion memory) SIMM in Error: U1702


Unexpected parity_memory_error at PC 0xffea1d4c.

Memory Error Address Register: 0x000ffffc. Instruction: d2030000.

Memory Error Control Register: 0x00000054.

Physical address: 0x004ffffc.

CPU board SIMM in Error: U1306 error: at addr 0x000ffffc, expect 0x000ffffc, obs0x00000002.(looping)

Physical address: 0x004ffffc.


Sun-4300 CPU Board Memory Addressing

ADDRESS (Dec) ADDRESS (Hex) BANK BYTE SOCKET

0-4MB 000000-3fffff 0 0 U1300

0-4MB

0-4MB

000000-3fffff

000000-3fffff

0

0

1

2

U1301

U1302

0-4MB

4-8MB

4-8MB

4-8MB

000000-3fffff

000000-7fffff

000000-7fffff

000000-7fffff

0

1

1

1

3

0

0

1

U1303

U1304

U1305

U1306 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00007/wcd00702.htm (1 von 4) [25.04.2002 16:02:34]


4-8MB 000000-7fffff 1 1 U1307

Sun 4300 Address Decoding

1st 3U Memory Board Addressing


8-12MB

8-12MB

800000-bfffff

800000-bfffff

0

0

0

1

U1600

U1601

8-12MB

8-12MB

12-16MB

12-16MB

800000-bfffff

800000-bfffff c00000-ffffff c00000-ffffff

0

0

1

1

2

3

0

1

U1602

U1603

U1604

U1605

12-16MB

12-16MB

16-20MB

16-20MB

16-20MB

16-20MB

20-24MB

20-24MB

20-24MB

20-24MB c00000-ffffff c00000-ffffff

1000000-13fffff

1000000-13fffff

1000000-13fffff

1000000-13fffff

1400000-17fffff

1400000-17fffff

1400000-17fffff

1400000-17fffff

1

1

2

2

2

2

3

3

3

3

2

3

0

1

2

3

0

1

2

3

U1606

U1607

U1700

U1701

U1702

U1703

U1704

U1705

U1706

U1707

2nd 3U Memory Board Addressing


24-28MB

24-28MB

1800000-1bfffff

1800000-1bfffff

0

0

0

1

U1600

U1601

24-28MB

24-28MB

28-32MB

28-32MB

1800000-1bfffff

1800000-1bfffff

1c00000-1ffffff

1c00000-1ffffff

0

0

1

1

2

3

0

1

U1602

U1603

U1604

U1605

28-32MB

28-32MB

32-36MB

32-36MB

32-36MB

32-36MB

36-40MB

36-40MB

1c00000-1ffffff

1c00000-1ffffff

2000000-23fffff

2000000-23fffff

2000000-23fffff

2000000-23fffff

2400000-27fffff

2400000-27fffff

1

1

2

2

2

2

3

3

2

3

0

1

2

3

0

1

U1606

U1607

U1700

U1701

U1702

U1703

U1704



36-40MB

36-40MB

2400000-27fffff

2400000-27fffff

3

3

2

3

U1706

U1707

1st 24 Mbytes of 9U Memory Board Addressing


8-12MB 800000-bfffff 0L 0 U1600

8-12MB

8-12MB

800000-bfffff

800000-bfffff

0L

0L

1

2

U1601

U1602

8-12MB

12-16MB

12-16MB

12-16MB

800000-bfffff c00000-ffffff c00000-ffffff c00000-ffffff

0L

0H

0H

0H

3

0

1

2

U1603

U1604

U1605

U1606

12-16MB

16-20MB

16-20MB

16-20MB

16-20MB

20-24MB

20-24MB

20-24MB c00000-ffffff

1000000-13fffff

1000000-13fffff

1000000-13fffff

1000000-13fffff

1400000-17fffff

1400000-17fffff

1400000-17fffff

0H

1L

1L

1L

1L

1H

1H

1H

3

0

1

2

3

0

1

2

U1607

U1700

U1701

U1702

U1703

U1704

U1705

U1706

20-24MB

24-28MB

24-28MB

24-28MB

24-28MB

28-32MB

28-32MB

28-32MB

28-32MB

1400000-17fffff 1H

1800000-1bfffff 2L

1800000-1bfffff 2L

1800000-1bfffff 2L

1800000-1bfffff 2L

1c00000-1ffffff 2H

1c00000-1ffffff 2H

1c00000-1ffffff 2H

1c00000-1ffffff 2H

1

2

3

0

3

1

2

3

0

U1707

U1800

U1801

U1802

U1803

U1804

U1805

U1806

U1807

2nd 24 Mbytes of 9U Memory Board Addressing


32-36MB 2000000-23fffff 3L 0 U1900

32-36MB

32-36MB

2000000-23fffff

2000000-23fffff

3L

3L

1

2

U1901

U1902

32-36MB

36-40MB

36-40MB

36-40MB

2000000-23fffff

2400000-27fffff

2400000-27fffff

2400000-27fffff

3L

3H

3H

3H

3

0

1

2

U1903

U1904

U1905



36-40MB

40-44MB

40-44MB

40-44MB

40-44MB

44-48MB

44-48MB

44-48MB

44-48MB

48-52MB

48-52MB

48-52MB

48-52MB

52-56MB

52-56MB

52-56MB

52-56MB

2400000-27fffff

3400000-1ffffff

3H

2800000-2bfffff 4L

2800000-2bfffff 4L

2800000-2bfffff 4L

2800000-2bfffff 4L

2c00000-2ffffff 4H

2c00000-2ffffff 4H

2c00000-2ffffff 4H

2c00000-2ffffff 4H

3000000-33fffff 5L

3000000-33fffff 5L

3000000-33fffff 5L

3000000-33fffff 5L

3400000-1ffffff 5H

3400000-1ffffff 5H

3400000-1ffffff 5H

5H

0

1

2

3

2

3

0

1

2

3

0

1

2

3

3

0

1

U2006

U2007

U2100

U2101

U2102

U2103

U2104

U2105

U2106

U2107

U1907

U2000

U2001

U2002

U2003

U2004

U2005




Sun 4400





Sun4/II: Troubleshooting - CPU - Interrupt Levels

Interrupt Levels

SPARC

Level 1 SW1

Sun-4

Level 2 VME1

Level 3 VME2

Sun-4c

SW1

SBus2

SBus3, SCSI

Sun-4m

SW1

SW2, VME1, SBus1

SW3, VME2, SBus2

Level 4 SW4, SCSI SW4

Level 5 VME3 SBus4, Ethernet

SW4, On-board SCSI

SW5, VME3, SBus3

Level 6 SW6, Ethernet SW6

Level 7 VME4 SBus5, Video

SW6, On-board Ethernet

SW7, VME4, SBus4

Level 8 Video

Level 9 VME5

SBus6

SBus7

Level 10 System C/T System C/T

Level 11 VME6 Floppy

SW8, On-board Video

SW9, VME5, SBus5

SW10, System C/T

SW11, VME6, SBus6, Floppy

Level 12 KBD/MS/SCC KBD/MS/SCC SW12, KBD/MS/SCC

Level 13 VME7 Audio SW13, VME7, SBus7, Audio

Level 14 Kernet C/T Kernel C/T SW14, Kernel C/T

Level 15 Memory Error Async Mem Error SW15, Async Errors



Sun4/II: Parts - Printer - Contents

Printer

Connector Pinouts

SBus Printer Card

SPARCprinter

Printers

LaserWriter II

SPARCprinter


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004dd.htm [25.04.2002 16:02:51]

Sun4/II: Parts - Printer - Pinouts


SBus Printer Card 501-1540 Video Port

SBus Printer Card 501-1910 Video Port

20-Pin to 25-Pin Cable 370-1365

20-Pin Hi-Density Female

PIN SIGNAL PIN SIGNAL

1 VCLK+ 11 VCLK-

2 LSYNC+ 12 LSYNC-

3 STATUS+ 13 STATUS-

4 PSYNC+ 14 PSYNC-

5 Do not use 15 Do not use



8 CBUSY18 CBUSY+

9 CMD+ 19 CMD-

10 VDATA+ 20 VDATA-

SBus Printer Card 501-1540 Parallel Port

SBus Printer Card 501-1910 Parallel Port



28-Pin Hi-Density Female


1 DATA 0 15 Do not use





6 DATA 5 20 GND

7 DATA 6 21 GND


9 GND 23 GND

10 DS 24 GND

11 BUSY 25 ACK

12 RESET 26 OUT/IN

13 AFXT 27 PE

14 SELECT 28 ERROR

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00674.htm (1 von 2) [25.04.2002 16:02:55]

Sun4/II: Parts - Printer - Pinouts


Sun4/II: Parts - Printer - SPARCprinter


SPARCprinter


25-Pin Female D-Sub


1 VCLK+ 14 VDATA+

5 LSYNC+ 18 LSYNC-

7 STATUS+ 20 LSYNC-

11 PSYNC+ 24 PSYNC-

23 CBUSY13 CBUSY+

9 CMD+ 22 CMD-

3 VDATA+ 16 VDATA-



Sun4/II: Parts - Printer - LaserWriter II

LaserWriter II

LW-1 LW-2 LW-3

115V LaserWriter 240V LaserWriter 115V LaserWriter

A4 Paper Tray


365-1040

370-1189

370-1196

536-1003

350-1015

330-1162

330-1163

LaserWriter II Assembly, A4 Paper Tray (240V)

LaserWriter II Print Engine (240V)

NT Controller PCA

AC Power Cord (240V)

A4 Paper Tray Assembly

A4 Paper Tray Base

A4 Paper Tray Top

365-1041

370-1188

370-1196

536-1002

350-1014

330-1160

330-1161

LaserWriter II Assembly, Letter/Legal Paper Tray (115V)


NT Controller PCA


Letter/Legal Paper Tray Assembly

Letter/Legal Paper Tray Base

Letter/Legal Paper Tray Top

365-1067

370-1188

370-1196

536-1002

350-1015

330-1162

330-1163

LaserWriter II Assembly, A4 Paper Tray (115V)


NT Controller PCA


A4 Paper Tray Assembly

A4 Paper Tray Base

A4 Paper Tray Top

150-1279 LaserWriter II Toner Cartridge

530-1172 LaserWriter Cable, DB-25 Male to DB-25 Male

530-1433 LaserWriter Cable, DB-25 Male to DB-25 Female




SPARCprinter

Option SPRN-400

Xerox 4030


365-1089 SPARCprinter (115V & 240V)

365-1124 Toner Cartridge 1

365-1125 Drum Cartridge 2

365-1126 Universal Paper Tray

365-1127 B4 Paper Tray

370-1365 Video Port Cable, Video Port to SPARCprinter

410-1017 Reusable Field Service Transit Case

501-1540 SBus Printer Board

530-1680 Parallel Port Cable

530-1683 Loopback Test Cable, Parallel Port to Video Port

530-1694 Test Cable, Video Port to Video Port

811-1345 Front Cover

811-1316 Corotron Assembly

811-1687 Fuser Wick 94E95090 (available from SunExpress)

1. The life of the Toner Cartridge is 8000 pages. A J5 error code indicates a low toner condition.

Reset the display when a new Toner Cartridge is installed.

a. Turn the AC power OFF.

b. Replace the Toner Cartridge.

c. Turn the AC power ON.

d. Press the Reset button located next to the power switch.

2. The life of the Drum Cartridge is 20,000 pages. Reset the print counter when a new Drum

Cartridge is installed.

a. Turn the AC power OFF.

b. Install a new Drum Cartridge.

b. Press and hold the Reset button located next to the power switch.

c. Turn the AC power ON.

d. Release the Reset button.

Do not reset the print counter unless a new Drum Cartridge is installed. Resetting the print counter without replacing the Drum Cartridge causes mechanical damage to the SPARCprinter when the toner sump fills.

SPARCprinter Operator Panel http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00677.htm (1 von 4) [25.04.2002 16:03:12]


SPARCprinter IOT Test Print

1. Switch the printer OFF.

2. Press and hold TEST.

3. Switch the printer ON.

4. Release TEST. 00 is displayed. The printer must warm-up for approximately one minute in order to print a test page.

5. Press ENTER to start printing the IOT test print. The display indicates the number of test pages printed.

6. Press ENTER to stop printing the IOT test print.

7. Switch the printer OFF to exit the IOT Test Print Mode.

Reference

SPARCprinter Service Guide, 800-5044-10.

SPARCprinter Input Component Tests


2. Press and hold ENTER.


4. Release ENTER. The Operator Panel displays 02.

5. Press ENTER to select the Input Component Tests. The Operator Panel displays 00.

6. The following input components can be tested: Fuser Exit Sensor, Toner Cartridge Switch,

Paper Size Sensors, Drum Cartridge Switch, Paper Tray Empty Sensors, Manual Bypass

Feature Switch, Reset Switch, Interlock Switch, and Test Switch. The input component is functional if the value displayed in the Operator Panel increases when the component is activated.

7. Switch the printer OFF to exit the Sensor Check Diagnostics http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00677.htm (2 von 4) [25.04.2002 16:03:12]


SPARCprinter Output Component Tests


2. Press and hold ENTER.


4. Press TEST until the desired diagnostic test number is displayed in the Operator Panel. The following output components can be tested:

Component

Print Counter

Upper Feed Clutch

Lower Feed Clutch

Test Code

30

80

81

Registration Clutch

Upper Turn Roll Clutch

82

84

Lower Turn Roll Clutch 84

Main Motor & Erase Lamp 90

HVPS 90

5. Press ENTER to test the component.

6. Switch the printer OFF to exit the Sensor Check Diagnostics.

SPARCprinter NVRAM Parameters


2. Press and hold TEST and ENTER.


4. Release TEST.

5. Release ENTER when the display shows 03.

6. The NVRAM parameter and value are displayed.

7. Press ENTER to change a value.

8. Press TEST to store a new value.

9. Press TEST to display the next parameter.

10. Switch the printer OFF to exit the NVRAM Parameters.

Function

Processing Direction

Address Content

0 xx 1

Scanning Direction

IOT Test Print

1

2 xx 2

NA 3

Fuser Temperature

Laser Power

3

4 xx 4 xx 4

Resolution

Video Mode

5

6 xx 4 xx 4 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00677.htm (3 von 4) [25.04.2002 16:03:12]


Configuration

Paper matrix

Console Type

7

8

9 xx 3 xx 4 xx 4

1. Processing Direction controls the top and bottom page margin. Each increment from 0 to F adjusts the margin 0.5 mm.

2. Scanning Direction controls the left and right page margin. Each increment from 0 to 8 adjusts the margin 0.5 mm.

3. Press ENTER to print one test page.

4. Do NOT change these factory settings.

SPARCprinter Error Codes

RAP

C3

C5

C9

E1

E4

E5

DESCRIPTION

No paper tray is detected.

The paper tray is empty.

A paper tray print was requested when there is paper in the manual feed tray.

A paper jam at the infeed roller has occurred.

A paper jam at the outfeed roller has occurred.

The top cover is open.

J2

J3

J4

J5

No drum cartridge is detected.

No toner cartridge is detected.

The drum cartridge has reached end of life.

The toner cartridge is empty.

P1 The fuser has shut down

U1

U2

U4

The main motor speed dropped below normal during a print cycle.

Laser Failure

Fuser Failure



Sun4/II: Parts - Monitor - Contents

Monitor

Monitor and Image Size

Connector Pinouts

Cables

12-inch Color LCD

14-inch Color CRT

14-inch Color Entry-Level CRT

14-inch Monochrome LCD

15-inch Color CRT

15-inch Monochrome CRT

16-inch Color CRT

16-inch Premium Color CRT

16-inch Mid-Range Color CRT


17-inch Entry-Level Color CRT

17-inch Greyscale CRT

19-inch Color CRT


19-inch Greyscale CRT

19-inch Greyscale CRT with OCLI

19-inch Monochrome CRT

19-inch Monochrome CRT with OCLI

19-inch Hi-Resolution CRT

19-inch Hi-Resolution CRT with OCLI


20-inch Premium Greyscale CRT


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004da.htm [25.04.2002 16:03:17]

Sun4/II: Parts - Monitor - Monitor and Image Size

Monitor and Image Size

Monitor size is the diagonal dimension of the CRT or the diagonal dimension of the CRT phosphor coating.

The image size of monitors may not be reflected in the monitor size listed in sales documents or price lists.

Image size is the horizontal and vertical dimension of the active display. The image size, or active display, is smaller than the CRT, Bezel, and Margin.

Sun Monitor Engineering Specifications define the horizontal and vertical dimensions of the image size shown in this section. The diagonal dimensions shown in this section are calculated from the horizontal and vertical dimensions and do not take into account CRT curvature.

The dimensions of the 19" Premium Color CRT are:

CRT Size: 20-inch diagonal (19" Phosphor Coating)

Bezel Size: 360 mm H x 283 mm V x 457 mm (17.99") D

Image Size: 350 mm H x 270 mm V x 442 mm (17.40") D



Sun4/II: Parts - Monitor - Connector Pinouts


Monochrome CRT

9-Pin Female D-Sub


1 VIDEO+ 6 VIDEO-

2 GND 7 GND

3 HSYNC 8 GND

4 VSYNC 9 GND

5 Not used

Color CRT DB13W3


1 Monitor specific 8 SENSE1


3 SENSE2

4 SRTN

5 CSYNC A2 Green

6 Monitor specific A3 Blue

7 Monitor specific

10 CRTN

A1 Red

Pins 1, 2, 6, and 7 are GND on the SBus GX+.

Pin-2 is VSYNC and Pin-6 is HSYNC on the SBus CG3.

Greyscale CRT DB13W3




3 SENSE2 10 CRTN

4 SRTN

5 CSYNC

A1 Not used

A2 Green

6 Monitor specific A3 Not used http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00652.htm (1 von 2) [25.04.2002 16:03:32]

Sun4/II: Parts - Monitor - Connector Pinouts

7 Monitor specific

Color CRT HD15 Connector


1 Red

2 Green

9 Not used

10 Sync Gnd

3 Blue 11 Gnd

4 Not used 12 DDC Data

5 Not used 13 Hsync

6 Red Gnd 14 Hsync

7 Green Gnd 15 DDC Clock

8 Blue Gnd



Sun4/II: Parts - Monitor - Cables

Video Cables


530-0492 Color CRT Cable, 4.6M, 1xBNC to 1xBNC




530-1415 Color CRT Cable, 50 cm, 4xBNC to 4xBNC

530-1440 Color CRT Cable, 1.2M, DB13W3 to DB13W3

530-1446 Color CRT Video Adapter Cable, 4xBNC to DB13W3

530-1509 Color CRT Cable, 4.6M, DB13W3 to DB13W3

530-1839 Color CRT Cable, 1.0M, 90° DB13W3 to DB13W3, 75 Ohm

530-1840 Color CRT Cable, 4.0M, 90° DB13W3 to DB13W3, 75 Ohm

530-1870 Color CRT Cable, 1.2M, DB13W3 to DB13W3, 75 Ohm

530-1898 Color CRT Cable, 4.5M, DB13W3 to DB13W3, 75 Ohm

530-2020 Color CRT Ext Cable, 3.0M, DB13W3M to DB13W3F, 75 Ohm

530-2357 Color CRT Video Adapter Cable, HD15M to DB13W3

530-1308 Greyscale CRT Cable, 4.6M, 2xBNC to 2xBNC

530-1363 Greyscale CRT Cable, 1.2M, 2xBNC to 2xBNC

530-1511 Greyscale CRT Video Adapter Cable, 2xBNC to DB13W3

530-1041 TTL Monochrome Cable, DB-9 to DB-9 (Sun-2/150U)

530-1109 CRT Monochrome Cable, 75 cm, DB-9 to DB-9

530-1125 TTL Monochrome Cable, 4.6M, DB-9 to DB-9

530-1133 CRT Monochrome Cable, 4.6M, DB-9 to DB-9

530-1242 CRT Monochrome Cable, 75 cm, DB-9 to DB-9





Sun4/II: Parts - Monitor - 12-inch Color LCD

12-inch Color LCD

Image Size:

239 mm Horizontal

179 mm Vertical

299 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Data

Clock

1024 x 768 51.9KHz

67.2Hz

27MHz*


540-2452 12" Color LCD

* The effective Pixel Rate for the 27.000MHz Data Clock is 54.000MHz.



Sun4/II: Parts - Monitor - 14-inch Color CRT

14-inch Color CRT

Image Size:

244 mm Horizontal

183 mm Vertical

305 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1024 x 768 53.6KHz

66Hz 70.4MHz


Seiko CM1421-03

360-1033 15V Monitor, FCC-A, 4xBNC

530-1370 Power Cord, IEC 320/CEE 22 to NEMA 5-15, USA

Seiko CM1421-33

360-1034 240V Monitor, FCC-A, 4xBNC

530-1583 Power Cord, IEC 320/CEE 22 to SEV 1011-24507, Swiss

530-1410 Power Cord, IEC 320/CEE 22 to CEE 7-VII, Europe

530-1411 Power Cord, IEC 320/CEE 22 to BS1363, UK

360-1035 115V Monitor, FCC-B, 4xBNC (obsolete)


360-1036 240V Monitor, FC-B, 4xBNC (obsolete)




BNC Adapter 530-1446

DB13W3 Connector


1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Red

5 Csync A2 Green

6 Not used A3 Blue

7 Not used http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00655.htm (1 von 2) [25.04.2002 16:03:37]


S2 is grounded. The Sense Code is 3.



Sun4/II: Parts - Monitor - 14-inch Entry-Level Color CRT

14-inch Entry-Level Color CRT

Image Size:

255 mm Horizontal

191 mm Vertical

319 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

800 x 600

1024 x 768

46.875KHz

48.363KHz

75.000Hz

60.004Hz

49.50MHz

65.00MHz


Samsung CQB4157L, .28 mm Dot-Pitch

365-1350 115V/240V Monitor, SVGA, HD-15

365-1351 115V/240V OEM Monitor, SVGA, HD-15

HD15 Connector


1 Red 9 Not used

2 Green

3 Blue

10 Sync Gnd

11 Gnd

4 Not used 12 DDC Data

5 Not used 13 Hsync

6 Red Gnd 14 Vsync

7 Green Gnd 15 DDC Clock

8 Blue Gnd



Sun4/II: Parts - Monitor - 14-inch Monochrome LCD

14-inch Monochrome LCD

Image Size:

274 mm Horizontal

214 mm Vertical

347 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Data

Clock

1152 x 900 64.5KHz

60.2Hz

4.9MHz *


540-2453 14" Monochrome LCD

* The effective Pixel Rate for the 4.9091MHz Data Clock is 78.5456MHz.





Image Size:

262 mm Horizontal

200 mm Vertical

329 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


Hitachi HM-4115-D-BA

360-1015 115V/240V Monitor, 4xBNC

180-1125 Power Cord, IEC 320/CEE 22 to pigtail

180-1097 Power Cord, IEC 320/CEE 22 to NEMA 5-15

Hitachi HM-4115-D-BA

360-1020 240V Monitor, 4xBN

150-1051 Fusecarrier

140-1034 Fuse, 2A





1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Red

5 Csync A2 Green

6 Not used A3 Blue

7 Not used





Image Size:

260 mm Horizontal

195 mm Vertical

325 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.5MHz

1024 x 768 62.0KHz

77Hz 84.37MHz


Nokia 449A101, .28 mm Dot-Pitch

365-1286 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, ELF/VLF with non-removable 1.2M Video Cable

Nokia 449A101, .28 mm Dot-Pitch

365-1327 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, ELF/VLF,

Energy Star, with non-removable 1.2M Video Cable



1 Connected to Pin-10 8 Sense1

2 Not used 9 Sense0

3 Sense2

4 Sgnd

5 Csync

6 Not used

7 Connected to Pin-10

10 Cgnd

A1 Red

A2 Green

A3 Blue

S0, S1, and S2 are grounded. The Sense Code is 0.

Note

The monitor synchronizes horizontally from 30KHz to 62KHz and vertically from 48Hz to

100Hz.



Sun4/II: Parts - Monitor - 15-inch Monochrome CRT

15-inch Monochrome CRT

Image Size:

250 mm Horizontal

187 mm Vertical

312 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1024 x 768 63.96KHz

76Hz 85.96MHz


360-1026 115V Monitor, DB9


360-1038 240V Monitor, DB9








Image Size:

295 mm Horizontal

230 mm Vertical

374 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


365-1020 115V Sony P2 GDM-1604-15 Monitor, 4xBNC

150-1225 Fuse, 4A


365-1022 240V Sony P2 GDM-1604-40 Monitor, 4xBNC

150-1226 Fuse, 3.15A


365-1063 115V Sony P2 GDM-1604B-15 Monitor, DB13W3

150-1225 Fuse, 4A


365-1064 240V Sony P2 GDM-1604B-40 Monitor, DB13W3

150-1226 Fuse, 3.15A


365-1079 115V Sony P2 GDM-1604A-15 Monitor, DB13W3, FCC-A

150-1225 Fuse, 4A


365-1080 240V Sony P2 GDM-1604A-40 Monitor, DB13W3, FCC-A

150-1226 Fuse, 3.15A

365-1092 115V Sony P2 GDM-1604B-15 Monitor, DB13W3, FCC-B

150-1225 Fuse, 4A


365-1093 240V Sony P2 GDM-1604B-40 Monitor, DB13W3, FCC-B

150-1226 Fuse, 3.15A

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065a.htm (1 von 2) [25.04.2002 16:04:02]


Philips/Fimi C1764

SPARCstation IPC Option LPC

365-1143 115V Monitor, DB13W3, FCC-B/VCCI-2

Philips/Fimi C1764

SPARCstation IPC Option LPC

365-1146 240V Monitor, DB13W3, FCC-B/VCCI-2

Notes

1. S0 and S1 are grounded. The Sense Code is 4.

2. DB13W3 Pins 1, 2, 6, and 7 are not used.



1 Connected to Pin-10 8 Sense1

2 Not used 9 Sense0

3 Sense2

4 Sgnd

5 Csync

6 Not used

7 Connected to Pin-10

10 Cgnd

A1 Red

A2 Green

A3 Blue



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065a.htm (2 von 2) [25.04.2002 16:04:02]

Sun4/II: Parts - Monitor - 16-inch Premium Color CRT

16-inch Premium Color CRT

Image Size:

295 mm Horizontal

230 mm Vertical

374 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

944 x 736

1076 x 824

1152 x 900

1152 x 900

70.8KHz

71.7KHz

61.8KHz

71.7KHz

84Hz

76Hz

66Hz

76Hz

Pixel

Frequency

92.94MHz *

105.5MHz **

92.94MHz

105.5MHz


Sony P3 GDM-1662, .31 mm Dot-Pitch

365-1096 115V/240V Monitor, DB13W3, FCC-A/VCCI-1 (not used)

Sony P3 GDM-1662 or GDM-1662B, .31 mm Dot-Pitch

365-1107 115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2

365-1113 115V/240V Monitor, DB13W3, FCC-B/VCCI-2

Sony P3 GDM-1662B, .31 mm Dot-Pitch

365-1130 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, VLF

365-1147 115V/240V Southern Hemisphere Monitor, DB13W3, VLF

Sony P3 GDM-1662B, .31 mm Dot-Pitch with Video Cable 530-1870

365-1159 115V/240V Monitor, DB13W3, FCC-B/VCCI-2, VLF

365-1161 115V/240V S. Hemisphere Monitor, DB13W3, VLF

365-1289 115V/240V OEM Monitor, DB13W3, VLF

* The Mode III (1024 x 800 @ 84) Overscan Mode user area is 944 x 736.

** The Mode II (1152 x 900 @ 76) Overscan Mode user area is 1076 x 824.

Notes

1. S0 is grounded. The Sense Code is 6.


3. The overscan mode is not supported at 66Hz vertical refresh.

4. The Frame Buffer revisions listed below do not decode the monitor sense code. Video is not displayed upon power-up until the video cable is removed and reconnected.

P4 CG6, 501-1505-03 and below http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065b.htm (1 von 2) [25.04.2002 16:04:05]


P4 CG6, 501-1532-09 and below

SBus CG6, 501-1481-04 and below

SBus CG6 501-1645-03 and below.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065b.htm (2 von 2) [25.04.2002 16:04:05]

Sun4/II: Parts - Monitor - 16-inch Mid-Range Color CRT

16-inch Mid-Range Color CRT

Image Size:

95 mm Horizontal

226 mm Vertical

371 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900

1024 x 768

61.8KHz

62.0KHz

66Hz

77Hz

92.94MHz

84.37MHz


365-1151

Sony CPD-1790

115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable

365-1164 115V/240V S. Hemisphere Monitor, DB13W3,

FCC-B/VCCI-2, with non-removable 1.2M Video Cable

365-1165 115V/240V European Monitor, DB13W3, FCC-B/VCCI-2,

Swedish MPR-2, with non-removable 1.2M Video Cable

365-1166 115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable



1 Not used 8 Sense 1


3 Sense2 10 Cgnd

4 Sgnd A1 Red

5 Csync A2 Green

6 Not used A3 Blue

7 Not used

S2 is grounded.

The Sense Code is 3.

SS4 Compatibility Matrix 1

MODEL PART # COMPATIBILE

Xterm 1 >=501-2540-03

Xterm 1 >=501-3025-02

70MHz >=501-2861-02

Yes

Yes

Yes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065c.htm (1 von 2) [25.04.2002 16:04:09]

Sun4/II: Parts - Monitor - 16-inch Mid-Range Color CRT

70MHz >=501-3002-02

85MHz >=501-2549-03

85MHz >=501-2928-02

110MHz >=501-3008-03

110MHz

110MHz

501-3109-xx

501-3134-xx

Yes

Yes

Yes

Yes

Yes 2

Yes 2

Notes:

1. If the SPARCstation 4 tcx frame buffer outputs sync on green, the board is not compatible with the 16-inch monitor. The monitor can not remove sync from the green output. Sync on green causes a higher than normal green output level. Refer to BugID 1218690.

2. Jumper J0501 on the SS4 CPU enables or disables sync on green.





Image Size:

300 mm Horizontal

234 mm Vertical

380 mm Diagonal

Pixel

Resolution

1152 x 900

1280 x 1024

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

71.81KHz

81.13KHz

76.14Hz

76.11Hz

108MHz

135MHz


365-1316

Sony N1 GDM-17E10, .26 mm Dot-Pitch


365-1319


115V/240V OEM Monitor, DB13W3, FCC-B/VCC1-2 with non-removable 1.2 Video Cable

365-1321


115V/240V Southern Hemisphere Monitor, DB13W3,

FCC-B/VCC1-2 with non-removable 1.2 Video Cable



1 RS232 clock in put 8 Sense1

2 RS232 data in

3 Sense2

9 Sense0

10 Cgnd

4

5

6

Sgnd

Csync

RS232 data out

7 Not used

A1 Red

A2 Green

A3 Blue





Image Size:

300 mm Horizontal

225 mm Vertical

375 mm Diagonal

Image Size:

293 mm Horizontal

234 mm Vertical

375 mm Diagonal


365-1338

Sony N2 GDM17E20, .26 mm Dot-Pitch


365-1339


115V/240V OEM Monitor, DB13W3, FCC-B/VCC1-2 with non-removable 1.2 Video Cable

365-1341


115V/240V Southern Hemisphere Monitor, DB13W3,

FCC-B/VCC1-2 with non-removable 1.2 Video Cable



1 SCL clock input for DDC1/2B 8 Sense1

2 +5Vdc from DDC framebuffer 9 Sense0

3 Sense2

4 Sgnd

5 Csync A2 Green

6 SDA bi-directional serial data A3 Blue

7 Sense3/Vsync

10 Cgnd

A1 Red

S0 and S3 are grounded. The Sense Code is 6.

Pin-5 is Hsync if Vsync is present on Pin-7.




17-inch Entry-Level Color CRT

Image Size:

300 mm Horizontal

225 mm Vertical

375 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900

1024 x 768

61.8KHz

62.0KHz

66Hz

77Hz

94.5MHz

84.3MHz


365-1343

Nokia, .28 mm Dot-Pitch


365-1345

Nokia, .28 mm Dot-Pitch

115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2, with non-removable 1.2M Video Cable





3 Sense2 10 Cgnd

4 Sgnd A1 Red

5 Csync A2 Green

6 Not used A3 Blue

7 S3/Vsync

S0, S1, and S2 are grounded.


Pin-7 is not connected on monitors marked DEV08773.

SS4 Compatibility Matrix 1

MODEL PART# COMPATIBILE

Xterm 1 >=501-2540-03

Xterm 1 >=501-3025-02

Yes

Yes

70MHz >=501-2861-02

70MHz >=501-3002-02

85MHz >=501-2549-03

Yes

Yes

Yes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065e.htm (1 von 2) [25.04.2002 16:04:13]


85MHz >=501-2928-02

110MHz >=501-3008-03

110MHz

110MHz

501-3109-xx

501-3134-xx

Yes

Yes

Yes 2

Yes 2

Notes

1. If the SPARCstation 4 tcx frame buffer outputs sync on green, the board is not compatible with the 17-inch monitor. The monitor can not remove sync from the green output. Sync on green causes a higher than normal green output level. Refer to BugID 1218690.

2. Jumper J0501 on the SS4 CPU enables or disables sync on green.



Sun4/II: Parts - Monitor - 17-inch Greyscale CRT

17-inch Greyscale CRT

Image Size:

295 mm Horizontal

230 mm Vertical

374 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


365-1055

Zenith 17SMM1

90-240V Monitor, DB13W3

365-1094

Zenith 17SMM1

90-240V Monitor, DB13W3, FCC-B/VCCI-2



1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Not used

5 Csync A2 Green

6 Not used A3 Not used

7 Not used


Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

914 x 690

1024 x 780

1024 x 800

1152 x 900

70.8KHz

71.7KHz

70.8KHz

71.7KHz

84Hz

76Hz

84Hz

76Hz

Pixel

Frequency

92.94MHz *

105.5MHz **

92.94MHz

105.5MHz


365-1100

Zenith 17SMM4-A

115V/240V Monitor, DB13W3, FCC-B/VCCI-2

365-1109

Zenith 17SMM4-B

115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0065f.htm (1 von 2) [25.04.2002 16:04:18]


365-1157

Zenith 17SMM4-A

115V/240V Monitor, DB13W3, FCC-B/VCCI-2, with Video Cable 530-1870

* The Mode III (1024 x 800 @ 84) Overscan Mode user area is 914 x 690.

** The Mode II (1152 x 900 @ 76) Overscan Mode user area is 1024 x 780.



1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Not used

5 Csync A2 Green


7 Not used






Image Size:

255 mm Horizontal

280 mm Vertical

452 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


540-1094

140-1022

180-1097

360-1008

Hitachi HM-4619, .31 mm Dot-Pitch

115V Monitor, 4xBNC, Metal Base

Fuse, 1.6A

Power Cord, IEC 320/CEE 22 to NEMA 5-15

19" Monitor

365-1000

140-1022

180-1097

180-1146

Ikegami DM-2050, .31 mm Dot-Pitch

Hitachi HM-4119-S-AA-0, .31 mm Dot-Pitch

Totoku CH-20U-64, .31 mm Dot-Pitch

115V Monitor, 4xBNC, 395x535 mm Base

Fuse, 1.6A



365-1006

140-1034

150-1051

180-1125



Fuse, 2A

Fusecarrier

Power Cord, IEC 320/CEE 22 to pigtail

365-1056

140-1022

180-1146



Fuse, 1.6A


365-1054

140-1034

150-1051

180-1125


Fuse, 2A

Fusecarrier


365-1073

Hitachi HM-4119-S-DA-0L, .31 mm Dot-Pitch

115V/240V Monitor, DB13W3, FCC-A, 409x409 mm Base

365-1038

150-1225

180-1146

Sony P2 GDM-1955A15, .31 mm Dot-Pitch

115V Monitor, 4xBNC

Fuse, 4A

Power Cord, IEC 320/CEE 22 to NEMA 5-15 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00660.htm (1 von 2) [25.04.2002 16:04:28]


365-1039

150-1226

180-1125


240V Monitor, 4xBNC

Fuse, 3.15A


365-1065

150-1225


115V Monitor, DB13W3

Fuse, 4A

365-1066

150-1226


240V Monitor, DB13W3

Fuse, 3.15A

365-1081

150-1225


115V Monitor, DB13W3, FCC-A/VCCI-1

Fuse, 4A

365-1082

150-1226


240V Monitor, DB13W3, FCC-A/VCCI-1

Fuse, 3.15A

Notes

1. S2 is grounded. The Sense Code is 3.






Image Size:

350 mm Horizontal

270 mm Vertical

442 mm Diagonal

Pixel

Resolution

1076 x 824

1152 x 900

1152 x 900

1280 x 1024

Horizontal

Frequency

Vertical

Frequency

71.7KHz

61.8KHz

71.7KHz

71.7KHz

76Hz

66Hz

76Hz

67Hz

Pixel

Frequency

105.5MHz *

92.94MHz

105.5MHz

117MHz


365-1095

365-1106

Sony P3 GDM-1962, .31 mm Dot-Pitch

115V/240V Monitor, DB13W3, FCC-A/VCCI-1

115V/240V OEM Monitor, DB13W3, FCC-A/VCCI-1 (obsolete)

365-1112

Sony P3 GDM-1962B, .31 mm Dot-Pitch

115V/240V Monitor, DB13W3, FCC-B/VCCI-2, VLF

365-1148 115V/240V Southern Hemisphere Monitor, DB13W3, VLF

365-1153 115V/240V European Monitor, DB13W3, FCC-B/VCCI-2,

Swedish MPR-2, with Video Cable 530-1870

365-1160

Sony P3 GDM-1962B with Video Cable 530-1870

115V/240V Monitor, DB13W3, VLF

365-1162 115V/240V S. Hemisphere Monitor, DB13W3, VLF

365-1288 115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2, VLF

* The Mode II (1152 x 900 @ 76) Overscan Mode user area is 1076 x 824.

Notes

1. S0 and S1 are grounded. The Sense Code is 4.


3. The overscan mode is not supported at 66Hz vertical refresh.

4. CG6 <=501-1505-03, <=501-1532-09, <=501-1481-04 or <=501-1645-03 do not decode the monitor sense code. No video is displayed when power is applied until the video cable is removed and reconnected.





19-inch Greyscale CRT

Image Size:

350 mm Horizontal

273 mm Vertical

443 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


540-1343

540-1514

140-1022

180-1097

180-1146



Fuse, 1.6A



540-1567

150-1215

180-1125


Fuse, 1.6A


365-1010

140-1022

180-1097

180-1146

Philips M19P114A/6161 or M19P114A/S102/6102


Fuse, 1.6A

Power Cord, IEC 320/CEE 22 to NEMA 5-15, USA


365-1009

150-1215

180-1125


Fuse, 1.6A


365-1053

140-1022

180-1146

Philips M19P114A/616120


Fuse, 1.6A


365-1046

150-1215

180-1125


Fuse, 1.6A


365-1071

Philips M19P114A/6127/20

115V/240V Monitor, DB13W3, FCC-A, 409x409 mm Base

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00662.htm (1 von 2) [25.04.2002 16:04:33]


1152 x 900

1076 x 824

71.7KHz

71.7KHz

76Hz

76Hz

105.5Mhz

105.5MHz *


365-1099

Philips M20P110A/710320

115V/240V Monitor, DB13W3, FCC-B/VCCI-2

365-1108

Philips M20P110A/710320

115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2

365-1140

Philips M20P110A/7132

115V/240V Monitor, DB13W3, FCC-B/VCCI-2, VLF

365-1154

Philips M20P110A/7132 or Capetronics DM8200

115V/240V Monitor, DB13W3, FCC-B/VCCI-2, VLF, with Video Cable 530-1870




1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Not used

5 Csync A2 Green


7 Not used




Sun4/II: Parts - Monitor - 19-inch Greyscale CRT with OCLI

19-inch Greyscale CRT with OCLI

Image Size:

350 mm Horizontal

273 mm Vertical

443 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 92.94MHz


365-1008

150-1051

150-1215

180-1125

Philips M19P114T/6103


Fusecarrier

Fuse, 1.6A


365-1052

150-1051

150-1215

180-1125


Fusecarrier

Fuse, 1.6A





1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Not used

5 Csync A2 Green


7 Not used

S2 is grounded in Adapter 530-1511.





19-inch Monochrome CRT

Image Size:

350 mm Horizontal

273 mm Vertical

443 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 100MHz


540-1062

360-1010

140-1022

180-1097

Moniterm VR1000L20 or Philips M19P114A/6102

115V Monitor, DB9, without Base (3/50 dimple top)

19" Monochrome Monitor

Fuse, 1.6A


365-1144

540-1893

540-1062

140-1022

180-1097


115V Monitor, DB9, 409x409 mm Base

409x409 mm Base Conversion Assembly

115V Monitor, DB9, without Base (3/50 dimple top)

Fuse, 1.6A


540-1562

150-1051

150-1215

180-1125



Fusecarrier

Fuse, 1.6A


540-1240

140-1022

180-1097



Fuse, 1.6A


365-1145

540-1893

540-1240

140-1022

180-1097



409x409 mm Base Conversion Assembly


Fuse, 1.6A


365-1016

140-1022

180-1097

180-1146

Elston DM60-19A0-A104

Philips M19P114A/6118/10


Fuse, 1.6A


Power Cord, IEC 320/CEE 22 to NEMA 5-15 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00664.htm (1 von 2) [25.04.2002 16:04:37]


365-1014

150-1051

150-1215

180-1125

Elston DM60-19A0-09-A104


Fusecarrier

Fuse, 1.6A


365-1051

140-1022

180-1097

180-1146

Philips M19P114A/612420


Fuse, 1.6A



365-1043

150-1051

150-1215

180-1125


Fusecarrier

Fuse, 1.6A


365-1086

Philips M19P114A/6128/20

115V/240V Monitor, DB9, FCC-A/VCCI-1



Sun4/II: Parts - Monitor - 19-inch Monochrome CRT with OCLI

19-inch Monochrome CRT with OCLI

Image Size:

350 mm Horizontal

273 mm Vertical

443 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

1152 x 900 61.8KHz

66Hz 100MHz


540-1358

140-1022

180-1097


115V Monitor (360-1023), DB9, without Base

Fuse, 1.6A


540-1565

150-1051

150-1215

180-1125


Fusecarrier

Fuse, 1.6A


540-1357

140-1022

180-1097


115V Monitor (360-1023), DB9, 395x535 mm Base

Fuse, 1.6A


365-1013

365-1044

140-1022

180-1097

180-1146




Fuse, 1.6A



365-1011

365-1045

150-1051

150-1215

180-1125




Fusecarrier

Fuse, 1.6A


365-1087

Philips M19P114A/6128/20

115V Monitor, DB9, 409x409 mm Base, FCC-a/VCCI-1



Sun4/II: Parts - Monitor - 19-inch Hi-Resolution CRT

19-inch Hi-Resolution CRT

Image Size:

355 mm Horizontal

279 mm Vertical

452 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

1600 x 1280 89.3KHz

Vertical

Frequency

67Hz

Pixel

Frequency

200MHz


540-1427

360-1014

140-1002

180-1097

Motorola L7101S-YO1


19-inch Monitor

Fuse, 3.15A


540-1571

150-1208

150-1051

180-1125


Fuse, 1.5A

Fusecarrier


365-1005

140-1002

180-1097

180-1146

Motorola L720IS-Y01 or Displaytek L720IS-Y01


Fuse, 3.15A



365-1007

365-1050

365-1128

150-1208

150-1051

180-1125

Motorola L7211S-Y01



240V Monitor, DB9, 409x409 mm Base, FCC-A/VCCI-1

Fuse, 1.5A

Fusecarrier


365-1047

365-1123

140-1002

180-1146

Motorola L7201S-Y01


115V Monitor, DB9, 409x409 mm Base, FCC-A/VCCI-1

Fuse, 3.15A




Sun4/II: Parts - Monitor - 19-inch Hi-Resolution CRT with OCLI

19-inch Hi-Resolution CRT with OCLI

Image Size:

355 mm Horizontal

279 mm Vertical

452 mm Diagonal

Pixel

Resolution

Horizontal

Frequency

1600 x 1280 89.3KHz

Vertical

Frequency

67Hz

Pixel

Frequency

200MHz


365-1004

140-1002

180-1097

180-1146

Motorola L7201S-Y01K


Fuse, 3.15A

Power Cord, IEC 320/CEE 22 to NEMA 5-15, USA


365-1003

150-1051

150-1208

180-1125

Motorola L7211S-Y01K


Fusecarrier

Fuse, 1.5A


365-1048

140-1002

180-1146


Fuse, 3.15A


365-1049

150-1051

150-1208

180-1125


Fusecarrier

Fuse, 1.5A






Image Size:

350 mm Horizontal

270 mm Vertical

442 mm Diagonal

Pixel

Resolution

1076 x 824

1196 x 938

1152 x 900

1152 x 900

1280 x 1024

1280 x 1024

Horizontal

Frequency

Vertical

Frequency

71.7KHz

81.1KHz

61.8KHz

71.8KHz

71.8KHz

81.1KHz

76Hz

76Hz

66Hz

76Hz

67Hz

76Hz

Pixel

Frequency

108MHz *

135MHz **

94.5MHz

108MHz

118MHz

135MHz


Sony P4 GDM-20D10, .31 mm Dot-Pitch

365-1167 115V/240V Monitor, DB13W3, FCC-B/VCCI-2,

MPR 1990:10 with non-removable 1.2M Video Cable

365-1313 115V/240V OEM Monitor, DB13W3, FCC-B/VCCI-2,


365-1317 115V/240V Southern Hemisphere Monitor, DB13W3,

FCC-B/VCCI-2, MPR 1990:10 with 1.2M Video Cable

365-1330 115V/240V Monitor, DB13W3, FCC-B/VCCI-2,


365-1322 115V/240V Sony P4 Korean Monitor, DB13W3, Energy Star, with non-removable 1.2M Video Cable

365-1324 115V/240V Sony P4 Monitor, DB13W3, Energy Star, with non-removable 1.2M Video Cable

365-1325 115V/240V Sony P4 S. Hemisphere Monitor, DB13W3,

Energy Star, with non-removable 1.2M Video Cable

365-1326 115V/240V Sony P4 OEM Monitor, DB13W3, Energy Star, with non-removable 1.2M Video Cable

370-1576

370-1705 none

Remote Control

Remote Control without Logo

CR2025 3V Battery, 20 mm diameter x 2.5 mm height


** The Mode I (1280 x 1024 @ 135) Overscan Mode user area is 1196 x 938.



1 RS232 clock in put 8 Sense1 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00668.htm (1 von 3) [25.04.2002 16:04:49]


2 RS232 data in

3 Sense2

4 Sgnd

5 Csync

6 RS232 data out

9 Sense0

10 Cgnd

A1 Red

A2 Green

A3 Blue


Pin-7 is not used.


Image Size:

350 mm Horizontal

270 mm Vertical

442 mm Diagonal

Pixel

Resolution

960 x 680

1152 x 900

1152 x 900

1280 x 1024

1280 x 1024

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

81.13KHz

71.81KHz

61.84KHz

81.13KHz

71.67KHz

112.37Hz

76.14Hz

66.00Hz

76.11Hz

66.67Hz

101MHz

108MHz

94.5MHz

135MHz

118MHz

PART# DESCRIPTION

Sony N2, .31 mm Dot-Pitch

365-1335 115V/240V Monitor, DB13W3, FCC-B, Energy Star with non-removable 1.2M Video Cable

365-1337 115V/240V OEM Monitor, DB13W3, FCC-B, Energy Star with non-removable 1.2M Video Cable

365-1340 115V/240V Southern Hemisphere Monitor, DB13W3, FCC-B,

Energy Star with non-removable 1.2M Video Cable

365-1342 115V/240V Korean Monitor, DB13W3, FCC-B,

Energy Star with non-removable 1.2M Video Cable



1 SCL DDC clock in put 8 Sense1

2 Not used 9 Sense0

3 Sense2

4 Sgnd

5 Csync

10 Cgnd

A1 Red

A2 Green http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00668.htm (2 von 3) [25.04.2002 16:04:49]


6 SDA serial data I/O A3 Blue

7 Vsync


Pin-5 is Hsync if Vsync is present on Pin-7.



Sun4/II: Parts - Monitor - 20-inch Premium Greyscale CRT

20-inch Premium Greyscale CRT

Image Size:

350 mm Horizontal

273 mm Vertical

443 mm Diagonal

Pixel

Resolution

1152 x 900

1280 x 1024

Horizontal

Frequency

Vertical

Frequency

Pixel

Frequency

71.8KHz

81.1KHz

76Hz

76Hz

105.5MHz

135MHz


365-1168

Zenith 20S5

115V/240V Monitor, DB13W3, FCC-B/VCCI-2,

MPR 1990:10 with non-removable 1.2M video cable

365-1320

Zenith 20S5

115V/240V Southern Hemisphere Monitor,

DB13W3, FCC-B/VCCI-2,

MPR 1990:10 with non-removable 1.2M video cable



1 Not used 8 Sense1

2 Not used 9 Sense0

3 Sense2 10 Cgnd

4 Sgnd A1 Not used

5 Csync A2 Green


7 Not used




Sun4/II: Parts - Input Device - Contents

Input Device

SunButtons

SunDials

Type-3 Keyboard

Type-3 Optical Mouse

Type-3 to Type-4 Spares Kit

Type-4 Keyboard

Type-5 Keyboard

Type-5c Keyboard

Type 101A Keyboard




Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004d7.htm [25.04.2002 16:04:57]

Sun4/II: Parts - Input Device - SunButtons

SunButtons

Option 180

Wiring Diagram

CODE PART # DESCRIPTION

595-1865 230V SunButtons Assembly

595-1884 115V SunButtons Assembly

1 300-1053 115V Power Supply


3 370-1291 SunButtons Box

4 540-1935 RFI Filter, DB-25

5 530-1610 DB-9M to DB-9F Cable, 600 mm

6 530-1525 DB-9 to DB-15 to DIN-5 Cable, 2.0M

NS 180-1125 230V AC Power Cord (obsolete)

NS 260-3861 Overlay Template


Sun4/II: Parts - Input Device - SunButtons


Sun4/II: Parts - Input Device - SunDials

SunDials

Option 190

Wiring Diagram


- 595-1737 115V SunDials Assembly

- 595-1773 230V SunDials Assembly



3 370-1223 Dialbox and Bale

4 540-1935 RFI Filter, DB-25

5 530-1610 DB-9M to DB-9F Cable, 600 mm

6 530-1525 DB-9 to DB-15 to DIN-5 Cable, 2.0M

NS 180-1125 230V AC Power Cord (obsolete)

NS 260-3257 Overlay Template


Sun4/II: Parts - Input Device - SunDials


Sun4/II: Parts - Input Device - Type-3 Keyboard

Type-3 Keyboard


370-1063 Type-3 Keyboard, DB-15 (obsolete)

370-1095 Type-3 Keyboard, DB-15

530-1526 Type-3 Keyboard Adapter Cable, DB-15 to Mini-Din



Sun4/II: Parts - Input Device - Type-3 Optical Mouse

Type-3 Optical Mouse


370-1058

370-1091

M3 Mouse and Pad, RJ11 (obsolete)

M3 Mouse and Pad, RJ11 (obsolete)

365-1042

370-1169

370-1171

370-1215

370-1368

M4 Mouse and Pad, RJ11

M4 Mouse, 200 CPI, RJ11

M4 Mouse Pad, 200 CPI, 0.062", 228.6 x 196.9 mm (obs)


M4 Mouse Pad, 200 CPI, 0.032", 177.8 x 196.9 mm



Sun4/II: Parts - Input Device - Type-3 to Type-4 Spares Kit

Type-3 to Type-4 Spares Kit


560-1501

320-1005

370-1170

370-1368

530-1443

530-1479

Type 3 Keyboard/Mouse to Type 4 Keyboard/Mouse Kit

Type-4 Keyboard, Mini-Din, US

M4 200 CPI Mouse, Mini-Din


Keyboard Cable, Mini-Din to Mini Din, 4.6M

Keyboard Cable, DB-15 to Mini Din, 4.6M




Type-4 Keyboard

Underside of Keyboard

DESCRIPTION

DIP SWITCH

1 2 3 4 5 6 7 8

Sun-3/4 w >=4.0 or 386i Off - - - -

Sun-3 w <=3.5

On - - - -

United States

Belgium/French

French Canadian

Danish

-

-

-

- - - -

- - - -

- - - -

-

- On -

- On On

- - - - On -

-

-

CODE

-

-

00

02

03

04

German

Italian

Dutch

Norwegian

Portuguese

Spanish

Swedish/Finnish

Swiss/French

Swiss/German

United Kingdom -

-

-

-

-

-

-

-

-

-

- - - - On - On

- - - - On On -

- - - - On On On

- - - On -

- - - On -

- - - On On -

-

- - - On - On -

-

- On

- - - On - On On

-

- - - On On - On

- - - On On On -

05

06

07

08

09

OA

OB

OC

OD

OE

Power

0.2 Amps @ +5Vdc

11.5 Watts


320-1002 Type-4 Keyboard, Mini-Din, US (obsolete)

320-1005 Type-4 Keyboard, Mini-Din, US

320-1006 Type-4 Keyboard, Mini-Din, German http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00639.htm (1 von 2) [25.04.2002 16:05:15]


320-1007 Type-4 Keyboard, Mini-Din, Swiss German

320-1008 Type-4 Keyboard, Mini-Din, Belgium and France

320-1009 Type-4 Keyboard, Mini-Din, UK

320-1010 Type-4 Keyboard, Mini-Din, Swiss French

320-1011 Type-4 Keyboard, Mini-Din, Netherlands

320-1012 Type-4 Keyboard, Mini-Din, Sweden and Denmark

320-1013 Type-4 Keyboard, Mini-Din, Denmark

320-1014 Type-4 Keyboard, Mini-Din, Norway

320-1015 Type-4 Keyboard, Mini-Din, Italy

320-1016 Type-4 Keyboard, Mini-Din, Spanish

320-1017 Type-4 Keyboard, Mini-Din, Portugal

320-1018 Type-4 Keyboard, Mini-Din, French Canadian

530-1442 Keyboard Cable, Mini-Din to Mini Din, 2.0M


530-1478 Keyboard Cable, DB-15 to Mini Din, 2.0M


530-1366 Sun386i Color and Keyboard Cable, DB21W4 to 4xBNC

530-1383 Sun386i Monochrome & Keyboard Cable, DB21W4 to DB9

530-1621 Sun386i Color & Keyboard Cable, DB21W4 to DB13W3




Type-5 Keyboard


DESCRIPTION

US

US/Unix

1 2 3

DIP SWITCH

4 5 6 7 8 CODE

- - On - On 21

- - On - On 22

French

Danish

German

Italian

- - On -

- - On -

- - On -

- - On -

- On On

- On -

- On On -

-

- On - On

23

24

25

26

Dutch

Norwegian

Portuguese

Spanish

- - On - On On On 27

- - On - On 28

- - On - On - On 29

- - On - On - On 2a

Swedish/Finnish - - On - On - On On 2b

Swiss/French - - On - On On 2c

Swiss/German - - On - On On - On 2d

UK - - On - On On On 2e

Korean

Taiwanese

- - On - On On On On 2f

- - On On 30

Nihon-go - - On On - On 31

French Canadian - - On On - On 32

Power

0.3 Amps @ +5Vdc

15.0 Watts


320-1072 Type-5 Keyboard, Mini-Din, US

320-1073 Type-5 Keyboard, Mini-Din, US/UNIX

320-1074 Type-5 Keyboard, Mini-Din, French http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0063a.htm (1 von 2) [25.04.2002 16:05:18]


320-1075 Type-5 Keyboard, Mini-Din, Danish

320-1076 Type-5 Keyboard, Mini-Din, German

320-1077 Type-5 Keyboard, Mini-Din, Italian

320-1078 Type-5 Keyboard, Mini-Din, Netherlands/Dutch

320-1079 Type-5 Keyboard, Mini-Din, Norwegian

320-1080 Type-5 Keyboard, Mini-Din, Portuguese

320-1081 Type-5 Keyboard, Mini-Din, Spanish

320-1082 Type-5 Keyboard, Mini-Din, Swedish

320-1083 Type-5 Keyboard, Mini-Din, Swiss/French

320-1084 Type-5 Keyboard, Mini-Din, Swiss/German

320-1085 Type-5 Keyboard, Mini-Din, UK

320-1086 Type-5 Keyboard, Mini-Din, Korean

320-1087 Type-5 Keyboard, Mini-Din, Taiwanese

320-1088 Type-5 Keyboard, Mini-Din, Nihon-go

320-1089 Type-5 Keyboard, Mini-Din, Finnish

320-1090 Type-5 Keyboard, Mini-Din, US without Sun Logo

320-1091 Type-5 Keyboard, Mini-Din, US/UNIX without Sun Logo

320-1092 Type-5 Keyboard, Mini-Din, Nihon-go without Sun Logo

320-1193 Type-5 Keyboard, Mini-Din, French Canadian








Sun4/II: Parts - Input Device - Type-5c Keyboard

Type-5c Keyboard

WIRE JUMPER

DESCRIPTION JS1 JS2 JS3 JS4 JS5

HEX

CODE

US In 21

US/Unix

Japanese

In 22

In In 31

DESCRIPTION

French

Danish

German

Italian

Dutch

Norwegian

Portuguese

DIP SWITCH

1 2 3 4 5

HEX

CODE

- On On 23

- On 24

- On - On 25

- On On 26

- On On On 27

- On 28

- On - On 29

Spanish - On - On 2a

Swedish/Finnish - On - On On 2b

Swiss/French - On On 2c

Swiss/German - On On - On 2d

UK

Korean

- On On On 2e

- On On On On 2f

Taiwanese On 30

French Canadian On On On On On 3f


320-1233 Type-5c Keyboard, 2M Cable, Mini-Din, US http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0063b.htm (1 von 2) [25.04.2002 16:05:21]

Sun4/II: Parts - Input Device - Type-5c Keyboard

320-1234 Type-5c Keyboard, 2M Cable, Mini-Din, US/UNIX

320-1252 Type-5c Keyboard, 2M Cable, Mini-Din, French

320-1236 Type-5c Keyboard, 2M Cable, Mini-Din, Danish

320-1237 Type-5c Keyboard, 2M Cable, Mini-Din, German

320-1238 Type-5c Keyboard, 2M Cable, Mini-Din, Italian

320-1239 Type-5c Keyboard, 2M Cable, Mini-Din, Netherlands/ Dutch

320-1240 Type-5c Keyboard, 2M Cable, Mini-Din, Norwegian

320-1241 Type-5c Keyboard, 2M Cable, Mini-Din, Portuguese

320-1242 Type-5c Keyboard, 2M Cable, Mini-Din, Spanish

320-1243 Type-5c Keyboard, 2M Cable, Mini-Din, Swedish

320-1245 Type-5c Keyboard, 2M Cable, Mini-Din, Swiss/French

320-1246 Type-5c Keyboard, 2M Cable, Mini-Din, Swiss/German

320-1247 Type-5c Keyboard, 2M Cable, Mini-Din, UK

320-1248 Type-5c Keyboard, 2M Cable, Mini-Din, Korean

320-1249 Type-5c Keyboard, 2M Cable, Mini-Din, Taiwanese

320-1253 Type-5c Keyboard, 2M Cable, Mini-Din, Nihon-go

320-1244 Type-5c Keyboard, 2M Cable, Mini-Din, Finnish

320-1235 Type-5c Keyboard, 2M Cable, Mini-Din, US/UNIX w/o Logo

320-1250 Type-5c Keyboard, 2M Cable, Mini-Din, Nihon-go w/o Logo

320-1251 Type-5c Keyboard, 2M Cable, Mini-Din, French Canadian

370-2002 Type-5 Keyboard Cable Adapter, F-to-F Mini-Din

530-2154 Keyboard Extension Cable, M-to-F Mini-Din, 2.7M

Note

The French-Canadian Type-5c Keyboard requires Solaris 2.4. Earlier versions of Solaris are not supported and no patches are available.



Sun4/II: Parts - Input Device - Type-101A Keyboard

Type-101A Keyboard



320-1070 Type 101A Keyboard, Mini-Din






Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0063c.htm [25.04.2002 16:05:24]




370-1161

365-1059

370-1170

370-1215

370-1368

M4 200 CPI Mouse and Pad, Mini-Din (unreleased, obs)

M4 200 CPI Mouse and Pad, Mini-Din

M4 200 CPI Mouse, Mini-Din







PART # DESCRIPTION f370-1398

370-1398

370-1399

370-1664

370-1663

Type-5 Mouse and Pad, Mini-Din

Type-5 Mouse, 300 CPI, Mini-Din

Type-5 Mouse Pad, 300 CPI, 196.6 x 178.0 mm

Type-5 Mouse without Sun Logo, 300 CPI, Mini-Din

Type-5 Mouse Pad without Sun Logo, 300 CPI

Notes

1. The Type-5 Mouse replaced the Type-4 Mouse in October 1993.

2. The Compact 1 Mouse replaced the Type-5 Mouse in August 1995.



Sun4/II: Parts - Board - Contents

Board

IDPROM

Boot PROM

Sun-4 Architecture

CPU

Sun-4 Architecture

Memory

Sun-4 SIMMs / Sun-4c SIMMs

Video

P4 Bus

VMEbus

Cables

SCSI

Multibus / VMEbus

Single-Ended 8-Bit SCSI Cables

IPI

ISP-80

Communication

Ethernet Accessories

VMEbus

Backplane

Miscellaneous

Boards

Board Hardware



Sun4/II: Parts - Board - IDPROM

IDPROM

The IDPROM address space provides system information including Machine Type, Serial Number,

Ethernet Address, and Manufacturing Date. This information may be stored in an IDPROM,

NVRAM, or EEPROM. The 32 Bytes of IDPROM content are shown below.

BYTE FIELD

1 Format

SIZE

1 Byte

2 Machine Type 1 Byte

3 Ethernet Address 6 Bytes

4 Date 4 Bytes

5 Serial Number 3 Bytes

6 Checksum

7 Reserved

1 Byte

16 Bytes

The Machine Type and Serial Number are combined to create the Hostid. Licensed software may use the Hostid.

Prior to the SPARCstation 10, the Machine Type was used by the operating system to identify the architecture and the architecture implementation.

Beginning with the SPARCstation 10, systems are not assigned a unique Machine Type. The device tree in the Open Boot PROM provides the system characteristics to the operating system. The high-order bit of the Machine Type is set to 1. The lower 7 bits of the Machine Type and Serial

Number fields are used at Sun's discretion.

The alpha-numeric code on the NVRAM barcode label can be used by Sun to create a duplicate

NVRAM. Provide this information when ordering a replacement NVRAM.

IDPROMs, NVRAMs, and EEPROMs are not interchangeable.

Programmed components that have a unique machine type are not interchangeable. For example, a new NVRAM is required when an SS2 (55xxxxxx) is upgraded to an SS20 (72xxxxxx).

Different component types are not interchangeable between systems. For example, a new NVRAM is required when an SS4 is upgraded (48T08) to an Ultra 1 Model 140 (48T59).

The 48T08 and 48T18 have the same pin count as the 48T59 but they are not pin compatible with the

48T59.

The NVRAM also contains a Time of Day clock. Accuracy of the clock is typically +/- 1 minute per month at 25°C. The 32,768Hz oscillator is tested not to exceed +/- 1.53 minutes per month (35PPM) error rate at 25°C.



NVRAM Component Types

NVRAM Battery Types

ARCH SYSTEM HOSTID COMPONENT TYPE PART # SOCKET http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00608.htm (2 von 3) [25.04.2002 16:05:36]


Sun-4

Sun-4d

Sun-4u

4/260/280

4/110/150

4/3xx

4/3xx

4/470/490

4/470/490

2100xxxx

22xxxxxx

23xxxxxx

None

24xxxxxx

None

IDPROM

IDPROM

IDPROM

48T02 NVRAM

IDPROM

48T02 NVRAM

Sun-4c

SS1

SS IPC

SS1+

SS SLC

SS ELC

SS IPX

SS2

4E

51xxxxxx

52xxxxxx

53xxxxxx

54xxxxxx

56xxxxxx

57xxxxxx

55xxxxxx

61xxxxxx

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

48T02 NVRAM

Sun-4m

SPARCclassic X

SPARCclassic

SS LX

SPARC Xterm 1

SS4

SS5

SS10

SS10SX

SS20

SS600MP

SS Voyager

JavaStation

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

72xxxxxx

72xxxxxx

72xxxxxx

71xxxxxx

80xxxxxx

80xxxxxx

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

48T18 NVRAM

48T08 NVRAM

48T08 NVRAM

48T08 NVRAM

SS1000/1000E

SS1000/1000E

SS1000/1000E

SC2000/2000E

SC2000/2000E

SC2000/2000E

A11

A12

A14

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

80xxxxxx

EEPROM

48T08 NVRAM

48T08 NVRAM

EEPROM

48T08 NVRAM

48T08 NVRAM

80xxxxxx

80xxxxxx

80xxxxxx

48T59 NVRAM

48T59 NVRAM

48T59 NVRAM

U1901

U805

U2202

U2200

U1404

U3505

U089

U0901

U089

U1011

U0813

U0512

U0512

U1101

U0707

U0707

U0707

U1605

U1605

U1506

U1004

U1004

U1004

U2701

U1506

U1505

U0209

U1007

U1007

U0203

U1205

U1205

U2006

U2006

U2006

520-1532

520-1638

523-2136

100-1628

525-1100

100-1628

525-1032

525-1084

525-1109

520-2749

525-1188

525-1180

525-1112

523-8151

525-1343

525-1203

525-1203

525-1391

525-1391

525-1369

525-1184

525-1184

525-1378

525-1181

525-1373

525-1657

100-2922

100-3528

100-4195

100-2922

100-2822

100-4195

525-1430

525-1430

525-1417



Sun4/II: Parts - Board - Boot PROM Sun-4

Boot PROM


Sun-4100 / Sun-4200 / Sun-4300

U601 U602

Sun-4/110/150

U603 U604 Revision

520-1651-03 520-1652-03 520-1653-03 520-1654-03 1.3

520-1651-04 520-1652-04 520-1653-04 520-1654-04 1.4

520-1651-06 520-1652-06 520-1653-06 520-1654-06 1.6

520-1651-07 520-1652-07 520-1653-07 520-1654-07 1.7

520-1651-08 520-1652-08 520-1653-08 520-1654-08 1.8

520-1651-09 520-1652-09 520-1653-09 520-1654-09 2.8.1

525-1651-10 525-1652-10 525-1653-10 525-1654-10 3.0

525-1651-11 525-1652-11 525-1653-11 525-1654-11 3.0.1

525-1651-12 525-1652-12 525-1653-12 525-1654-12 3.0.2

595-1964-xx Boot PROM Kit

Sun-4/260/280

U2004 U2003 U2002 U2001 Revision

520-1504-01 520-1505-01 520-1506-01 520-1507-01 0.68

520-1504-02 520-1505-02 520-1506-02 520-1507-02 1.0

520-1504-03 520-1505-03 520-1506-03 520-1507-03 1.1

520-1504-04 520-1505-04 520-1506-04 520-1507-04 1.3

520-1504-05 520-1505-05 520-1506-05 520-1507-05 1.7

520-1504-06 520-1505-06 520-1506-06 520-1507-06 2.8

525-1071-01 525-1074-01 525-1075-01 525-1076-01 2.8.4

525-1071-02 525-1074-02 525-1075-02 525-1076-02 3.0

595-1965-xx Sun 4200 Boot PROM Kit

Sun-4/310/350/360/370/380/390

U2100 U2103 U2102 U2101 Revision

525-1035-04 525-1036-04 525-1037-04 525-1038-04 1.1

525-1035-05 525-1036-05 525-1037-05 525-1038-05 3.0

525-1035-06 525-1036-06 525-1037-06 525-1038-06 3.0.1

525-1035-07 525-1036-07 525-1037-07 525-1038-07 3.0.2

525-1035-08 525-1036-08 525-1037-08 525-1038-08 3.0.3

525-1035-09 525-1036-09 525-1037-09 525-1038-09 4.1.1

595-1961-xx Sun 4300 Boot PROM Kit http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0060b.htm (1 von 2) [25.04.2002 16:05:40]

Sun4/II: Parts - Board - Boot PROM Sun-4

Sun-4/470/490

U3504 U3503 U3502 U3501 Revision

525-1103-01 525-1104-01 525-1105-01 525-1106-01 0.1.d

525-1103-02 525-1104-02 525-1105-02 525-1106-02 0.2.c

525-1103-03 525-1104-03 525-1105-03 525-1106-03 3.0

525-1103-04 525-1104-04 525-1105-04 525-1106-04 4.0

525-1103-06 525-1104-06 525-1105-06 525-1106-06 4.1.1

595-2123-xx Sun 4400 Boot PROM Kit



Sun4/II: Parts - Board - CPU Sun-4

CPU


Sun 4100 / Sun 4200 / Sun 4300 / Sun 4400


501-1199 8MB Sun 4100 CPU (270-1199-03) without FPC



501-1237 8MB Sun 4100 CPU (270-1199-03) with FPC4 or FPC6


501-1657 8MB Sun 4100 CPU (270-1199-07) with FPC6













501-1129 0MB Sun 4200 CPU with FPC4 (obsolete)

501-1274 0MB Sun 4200 CPU with FPC4 or FPC6, 1-Slot Backpanel

501-1491 0MB Sun 4200 CPU with FPU-2, 2-Slot Backpanel

501-1522 0MB Sun 4200 CPU with FPC4 or FPC6, 2-Slot Backpanel

SPARCstation 330, SPARCstation 370, SPARCserver 390

501-1316 8MB Sun 4300 CPU with 1MB SIMMs

501-1742 32MB Sun 4300 CPU with 4MB SIMMs

SPARCstation 470, SPARCserver 490

501-1381 0MB Sun 4400 CPU

501-1899 0MB Sun 4400 CPU

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0060c.htm (1 von 2) [25.04.2002 16:05:42]

Sun4/II: Parts - Board - CPU Sun-4


Sun4/II: Parts - Board - Memory

Memory

Sun-4 SIMMs


501-1314 256KB, 256KB x 9-Bit SIMM, Sun 4100

501-1544 1MB, 1Mbit x 9-Bit SIMM, Sun 4300

501-1408 1MB, 1Mbit x 9-Bit SIMM, Sun-3/80 and Sun-4/60/65/300





501-1739 4MB, 1Mbit x 9-Bit SIMM, Sun-4/40/60/65/75/300

Sun 4300 / Sun 4400 / Sun-4/E


501-1436 8MB Sun-4/330 Parity Memory with 1MB SIMMs






501-1564 8MB Sun 4300 Memory, with 1MB SIMMs

501-1563 24MB Sun 4300 Memory with 1MB SIMMs



501-1333 32MB Sun 4400 ECC Memory

501-1721 128MB Sun 4400 ECC Memory

501-8036 16MB Sun-4/E ECC Memory

501-8042 4MB Sun-4/E ECC Memory

501-8060 0MB Sun-4/E Combo Memory and 2-Slot SBus Expansion



Sun4/II: Parts - Board - Video - P4 Bus

Video

P4 Bus


501-1247 MG3 ECL Frame Buffer, DB-9

501-1248 CG4 Color Frame Buffer, BNC

501-1371 CG8 Color Frame Buffer, BNC

501-1402 MG4 ECL/Analog Frame Buffer, DB-9/DB13W3

501-1518 CG8 Color Frame Buffer, DB13W3

GX Graphics Option






Sun4/II: Parts - Board - Video - VMEbus

Video

VMEbus


501-1014 CG2 Color Frame Buffer

540-1126 CG2 Color Frame Buffer (obsolete)

599-1165 CG2 Color Frame Buffer (obsolete)

501-1089 CG3 Double Buffered Color Frame Buffer


501-1319 CG3 Double Buffered Color Frame Buffer, 1024x1024


501-1055 GP Graphics Processor

501-1139 GP+ Graphics Processor Plus

501-1268 GP2 Graphics Processor Two

501-1058 GB Graphics Buffer

501-8020 Sun-3/E Monochrome Frame Buffer

501-8029 Sun-3/E Color Frame Buffer

501-1383 TAAC-1 Application Accelerator

501-1447 TAAC-1 Application Accelerator

CXP Graphics Option


501-1139 GP+ Graphics Processor Plus


GXP Graphics Option

501-1434 CG9 24-bit Color Frame Buffer


VX and MVX Graphics Options

501-1537 Visualization Accelerator Pixel Processor

501-1538 Visualization Accelerator Super Frame Buffer

501-1596 Pixel Processor to Super Frame Buffer Connector

340-2468 VX and MVX Frontplane EMI Cover

340-2469 VX Frontplane EMI Cover


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0060f.htm [25.04.2002 16:05:56]

Sun4/II: Parts - Board - Video - Cables

Video

Cables


530-0492 Color Cable, 4.6M, 1xBNC to 1xBNC




530-1415 Color Cable, 50 cm, 4xBNC to 4xBNC

530-1440 Color Cable, 1.2M, DB13W3 to DB13W3

530-1446 Color Adapter Cable, 4xBNC to DB13W3

530-1509 Color Cable, 4.6M, DB13W3 to DB13W3

530-1839 Color Cable, 1.0M, 90_ DB13W3 to DB13W3, 75 Ohm

530-1840 Color Cable, 4.0M, 90_ DB13W3 to DB13W3, 75 Ohm

530-1870 Color Cable, 1.2M, DB13W3 to DB13W3, 75 Ohm

530-1898 Color Cable, 4.5M, DB13W3 to DB13W3, 75 Ohm

530-2020 Color Extension Cable, 3.0M, DB13W3M to DB13W3F, 75 Ohm

530-1308 Greyscale Cable, 4.6M, 2xBNC to 2xBNC

530-1363 Greyscale Cable, 1.2M, 2xBNC to 2xBNC

530-1511 Greyscale Adapter Cable, 2xBNC to DB13W3

530-1041 TTL Monochrome Cable, DB-9 to DB-9, Sun-2/150U

530-1109 ECL Monochrome Cable, 0.75M, DB-9 to DB-9

530-1125 TTL Monochrome Cable, 4.6M, DB-9 to DB-9







Sun4/II: Parts - Board - SCSI - Multibus

SCSI

Multibus / VMEbus


501-1006 Sun-2 Multibus SCSI Host Adapter

501-1045 Sun-2 VMEbus SCSI Host Adapter

501-1120 Sun-3 VMEbus SCSI Host Adapter (obsolete)

501-1236 Sun-3 VMEbus SCSI Host Adapter

501-8027 Sun-3/E VMEbus SCSI Host Adapter

501-1147

501-1045

501-1079

Sun-2/50 SCSI Host Adapter Assembly, External SCSI

Sun-2 VMEbus SCSI Host Adapter

Sun-2/50 0mb Memory Expansion Board

501-1149

501-1045

270-1059

Sun-2 SCSI Host Adapter Assembly, Internal SCSI

Sun-2 SCSI Host Adapter

VME 3x2 Adapter FAB with P2 Rows A&C

501-1138

501-1045

270-1138

Sun-2 SCSI Host Adapter Assembly, External SCSI


VME 3x2 Adapter FAB without P2 Rows A&C

501-1167

501-1045

270-1059




501-1170

501-1236

270-1059

Sun-3 SCSI Host Adapter Assembly, Internal SCSI



501-1217

501-1236

270-1138



VME 3x2 Adapter FAB without P2 Rows A&C



Sun4/II: Parts - Board - SCSI - Single SCSI Cables

SCSI

Single-Ended 8-Bit SCSI Cables


530-1185 External Cable, DD-50SA to DD-50SA, Ribbon, 1.0M (obs)

530-1186 External Cable, DD-50SA to DD-50SA, Ribbon, 5.0M (obs)

530-1249 External Cable, DD-50SA to DD-50SA, 1.0M



530-1365 External Cable, DD-50SA to DD-50SA, 41 cm

530-1435 External Cable, 50-Pin SCSI-2 to DD-50SA, 2.0M


530-1792 External Cable, 50-Pin SCSI-2 to DD-50SA w Ferrites, 2.0M

530-1829 External Cable, 50-Pin SCSI-2 to DD-50SA w Ferrites, 1.0M

530-1434 External SCSI-2 Cable, 50-Pin to 50-Pin, 45 cm

530-1508 External SCSI-2 Cable, 50-Pin to 50-Pin, 80 cm

530-1793 External SCSI-2 Cable, 50-Pin to 50-Pin w Ferrites, 80 cm

530-1836 External SCSI-2 Cable, 50-Pin to 50-Pin w Ferrites, 2.0M

530-1852 External SCSI-2 Cable, 50-Pin to 50-Pin w Ferrites, 4.0M,

530-2055 Ext SCSI-2 Cable, 50-Pin to 90_ 50-Pin w Ferrites, 1.12M

530-2056 Ext SCSI-2 Cable, 50-Pin to 90_ 50-Pin w Ferrites, 1.65M

530-1501 External Cable, DD-50SA to Centronics, 2.0M

530-1502 External Cable, Centronics to Centronics, 1.5M

530-1503 External Cable, 50-Pin SCSI-2 to Centronics, 2.0M

530-1568 External Cable, DD-50SA to Centronics, 4.0M

530-1900 External Cable, 50-Pin SCSI-2 to Centronics, 4.0M

150-1346 External Passive Terminator, 50-Pin SCSI-2

150-1407 External Passive Terminator, 50-Pin Centronics

150-1785 External Active Terminator, 50-Pin SCSI-2

150-2283 External Forced Perfect Terminator, 50-Pin SCSI-2

530-1381 External Passive Terminator, 50-Pin DD-50SA



Sun4/II: Parts - Board - IPI - ISP-80

IPI

ISP-80


501-1539

501-1855

530-1487

530-1488

530-1489

530-1518

530-1536

530-1788

530-1789

ISP-80 IPI-2 DIsk Controller

ISP-80 IPI-2 DIsk Controller

IPI Command Cable, 8.0M (obsolete)

IPI Command Cable, 1.0M

IPI "W" Command Cable (not released)

IPI Command Cable, 2.0M (obsolete)




ISP-80 Firmware

U0501 U0502 U0503 DESCRIPTION

525-1023-01 525-1024-01 525-1025-01 Engineering release

525-1023-01 525-1024-02 525-1025-02 Bug fixes

525-1023-01 525-1024-03 525-1025-03 Bug fixes

525-1023-01 525-1024-04 525-1025-04 Bug fixes

525-1023-01 525-1024-05 525-1025-05 Bug fixes

525-1023-01 525-1024-06 525-1025-06 Bug fixes

525-1023-05 525-1024-07 525-1025-07 6MB/Sec support

525-1023-05 525-1024-08 525-1025-08 Prestoserve support

525-1023-05 525-1024-09 525-1025-09 Dual Port support

525-1023-05 525-1024-10 525-1025-10 Dual Port/Timeout fixes



Sun4/II: Parts - Board - Communication - Ethernet Accessories

Communication

Ethernet Accessories


130-1240 BNC Female to N-series Male Option TA-M

130-1241 BNC Male Terminator Option TT-M

130-1242 BNC "T",F,M,F Option TTC

130-1243 BNC Barrel, Double Female Option TBC

130-1244 BNC Terminator, Female Option TT-F

130-1245 BNC Female to N-series Female Option TA-F

370-0288 3Com 3c400 Controller (obsolete)

370-0331 3Com 3c100 Transceiver (obsolete)

370-0363 15-meter Ethernet Coax Cable (obsolete)

370-0364 15-meter Transceiver Drop Cable (obsolete)

370-0368 N-series Male Terminator Option ETR

370-0549 N-series Connector

370-1071 3Com 3C101/102 Transceiver (370-1071-01) (obsolete)

370-1071 3Com 3C106 Transceiver (370-1071-02)

370-1072 Vampire Tap Block, AMP 228752-1

370-1073 N-series Tap Block, 3Com 3C139

370-1074 BNC Tap Block, 3Com 3C139A

370-1075 Vampire Tap Tool Option ETH-TAP-TOOL

530-1241 15-meter Transceiver Drop Cable

530-1253 15-meter Thin Ethernet Cable Option TS-15M

530-1254 15-meter Ethernet Coax Cable Option ECX

530-1280 5-meter Thin Ethernet Cable Option TS-5M

530-1519 Adapter Cable, 250 mm

530-1696 Adapter Cable, Sun-4/20, 2.0M

xxx-xxxx If the customer uses the AMP type attachment, an N-series female terminator (not available from Sun), is needed to terminate the coaxial cable.

----AMP

-----***-------------|Male End| <----Terminator


370-1071

370-1072

530-1241

Option TAP

3Com 3C106 Transceiver

Vampire Tap Block, AMP 228752-1

15-meter Transceiver Drop Cable http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00614.htm (1 von 2) [25.04.2002 16:06:17]

Sun4/II: Parts - Board - Communication - Ethernet Accessories

370-1071

370-1072

530-1241

530-1254

Option INLINE



15-meter Transceiver Drop Cable

15-meter Ethernet Coax Cable Option ECX

370-1071

370-1072

530-1241

530-1253

Option Thin



15-meter Transceiver Drop Cable

15-meter Thin Ethernet Cable Option TS-15M

530-1871

530-1871

530-2093

530-2149

530-2150

Twisted Pair Ethernet Cables

530-1871-xx, Category 3, RJ45 to RJ45, 4M

530-1871-04, Category 5, RJ45 to RJ45, 4M

Shielded RJ45 to RJ45, 4M

Category 5, Back-to-Back, RJ45 to RJ45, 1.0M

Category 5, Back-to-Back, RJ45 to RJ45, 5.0M

530-2027

530-2027

530-2105

530-2105

SPARCcluster 1 Ethernet Cables

520-2027-01 Category 3 System Rack Cable

520-2027-02 Category 5 System Rack Cable

520-2105-01 Category 3 Expansion Rack Cable

520-2105-02 Category 5 Expansion Rack Cable



Sun4/II: Parts - Board - Communication - VMEbus

Communication

VMEbus

Ethernet / FDDI / Network CoProcessor


501-8027 Sun-3/E SCSI/Ethernet Controller

501-1153

501-1004

530-1173

Sun-2 Ethernet Controller Assembly

Sun-2 Multibus Ethernet Controller

Ethernet Cable, Ethernet Controller to Backpanel

501-1584

501-8027

530-1607

Sun-3/E Ethernet Controller Assembly

Sun-3/E Ethernet Controller

Ethernet Cable, Ethernet Controller to Backpanel

501-1276

537-1000

SunLight FDDI

Fiber Optical Cable, 15M

370-1396 Sun Network CoProcessor (Interphase NC400, obsolete)

370-1421 Sun Network CoProcessor

501-1920 Sun Network CoProcessor (unreleased part, not available)

ALM / ALM-2


501-1157

370-1040

370-1047

370-1048

370-1097

370-1099

370-1100

530-1251

530-1252

530-1255

540-1281

540-1558

16-Channel Asychronous Line Multiplexer (ALM)

Systech MTI-1600 Board Set

Systech MTI-1600 Controller Board

Systech MTI-1600 USART Board

Systech MTI-1650B Board Set

Systech MTI-1650B Controller Board

Systech MTI-1650B USART Board

Cable, Systech Controller to Systech USART

Cable, Systech MTI-1600/1650B to Backpanel

DC Power Cable

RS-232 Loopback Test Plug (obsolete)


501-1165

370-1096

370-1099

811-1100

530-1276

530-1281

530-1295

540-1281

540-1558

16-Channel Asychronous Line Multiplexer (ALM)

Systech MTI-1650A Board Set

Systech MTI-1650B Controller Board

16-Channel USART Panel

RS-232 Cable, Systech MTI-1650A to Backpanel

DC Power Cable, ALM to Backpanel

DC Power Cable, ALM to USART Panel

RS-232 Loopback Test Plug (obsolete)

RS-232 Loopback Test Plug http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00615.htm (1 von 2) [25.04.2002 16:06:27]

Sun4/II: Parts - Board - Communication - VMEbus

501-1203

530-1312

530-1315

340-1569

340-1587

340-1914

340-1915

530-1334

540-1526

540-1558

540-1560

16-Channel Asychronous Line Multiplexer-2 (ALM-2)

Internal Parallel Port Cable, 14.5 cm

Internal Cable, 50-Pin, 11.5 cm

Rack Mounting Bracket

Wall Mounting Bracket

Rack Mounting Bracket, Short, 56" Rack

Rack Mounting Bracket, Long, 56" Rack

Cable, ALM-2 to DCA, 2.4M

DCA Assembly


Parallel Port Loopback Test Plug

MCP / HSI / Channel Adapter


501-1221

530-1313

530-1314

540-1558

540-1559

SunLink Multiprotocol Communications Processor (MCP)

Internal RS-232 Cable, 17.5 cm

Internal RS-449 Cable, 17.5 cm



501-1338

530-1425

530-1426

530-1430

SunLink High-Speed Serial Interface (HSI)

V.35 Cable, HSI to DSU, 2.9M

V.35 Loopback Test Plug


370-1128

501-1460

530-1134

370-1135

370-1136

370-1129

370-1130

370-1131

370-1132

530-1364

SunLink Channel Adapter (do not use, see FCO A0003-1)

SunLink Channel Adapter

Loopback Test Cable

Bus Terminator

Tag Terminator

Tag and Bus In Cable, 8' (do not use -01, -02, or -03)

Tag and Bus Out Cable, 8' (do not use -01, -02, or -03)

Tag and Bus Out Cable, 5' (obsolete)

Tag and Bus In Cable, 5' (obsolete)

RS-232 Diagnostic Port Cable, 20'



Sun4/II: Parts - Board - Backplane

Backplanes and I/O Boards


501-1092 12-Slot VMEbus Backplane, (obsolete)

501-1117 12-Slot VMEbus Backplane, Pressfit




501-1439 12-Slot Backplane, 9 VMEbus Slots, Pressfit (obsolete)

501-1498 16-Slot Backplane, 13 VMEbus Slots, Pressfit (obsolete)

501-1597 16-Slot Backplane, 13 VMEbus Slots, Pressfit, Fused

501-1598 12-Slot Backplane, 9 VMEbus Slots, Pressfit

501-1832 12-Slot Backplane, 9 VMEbus Slots, Pressfit with cutout



Sun4/II: Parts - Board - Miscellaneous - Boards

Miscellaneous

Boards


501-1154 VMEbus to Multibus Adapter Assembly, Blank Backpanel

501-1191 VME 3x2 Adapter Assembly, without P2 A&C, Option 160B

501-1220 VME 3x2 Adapter Assembly, without P2 A&C

501-1269 VME 3x2 Adapter Assembly, with P2 A&C, Option 160A

501-1384 Sun 4100 FPU2

501-1387 Sun 4200 FPU2

501-1454 Sun-4/60 FPU

501-1666 VME 3x2 Adapter Assembly, with P2 A&C

540-1108 VME 3x2 Adapter Assembly (obsolete)

540-1250 VMEbus to Multibus Adapter Assembly (obsolete)

501-1125

501-1214

501-1196

370-1125

SunIPC without 80287

SunIPC with 80287

Parallel Port Loopback Test Plug

Floppy Drive Cable, SunIPC to Floppy Drive



Sun4/II: Parts - Board - Miscellaneous - Board Hardware

Miscellaneous

Board Hardware


130-0272 2-Pin Shunt, 0.10" Pin Spacing, 0.025" Pin Diameter

130-2190 2-Pin Shunt, 2.0 mm Pin Spacing, 0.50 mm Pin Diameter

240-1287 Hex Screw, M2.5 0.45 x 16 mm

240-1288 Hex Screw, M2.5 0.45 x 10 mm

340-1407 Air Restrictor, 9U Cardcage

340-1818 Rear Panel, MG4 Analog/ECL Frame Buffer

540-1433 Single Slot Filler Panel, 9U Cardcage

540-1809

150-1192

240-1426

240-1571

330-1099

340-1601

340-1602

340-1605

340-1611

Rear Panel Assembly, P4 Video, Sun 4300/4400 CPU

Tape (required, not included)

M3 Nut

#4-40 Jackscrew

Insulator (required, not included)

Filler Panel, 9-Pin Connector

Filler Panel, 25-Pin Connector

BNC Filler Panel, Internal

BNC Filler Panel, External

330-1099 P4 Video Insulator, Sun 4300/4400 CPU

150-1192 Tape, P4 Video Insulator, Sun 4300/4400 CPU

560-1183

330-1100

Spring Finger Insulation Kit

Insulator Shield

150-1022 Lithium Battery, 3.0Vdc

150-1164 Silver Oxide Battery, 1.55Vdc

150-1022 Lithium Battery, 3.0Vdc



Sun4/II: Parts - Miscellaneous Options - Contents

Miscellaneous Options

Option 955

56-inch Expansion Cabinet

Option 960

76-inch Expansion Cabinet



Sun4/II: Parts - Miscellaneous Options - 56-inch Expansion Cabinet

955

56-inch Expansion Cabinet

CODE PART #

1 340-1884 Anti-Tilt Panel

DESCRIPTION

2 540-1857 Vented Panel Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0064c.htm (1 von 2) [25.04.2002 16:06:51]


3 540-1947 1/2" Tape Panel Assembly with Cutout

4 540-2252 Front Panel with 4 Tape Drive Cutouts

5 540-1859 Cap Panel Assembly

6 240-1630 #6-32 Ballstud

7 340-1840 Top Panel

8 540-2393 Keyswitch Assembly (replaced 540-1285)

9 340-1913 Filler Panel, 5.2" x 19"

10 340-1885 Side Restraint Bracket, Upper

11 240-1372 M4 0.7 x 10 mm Screw

12 540-1718 Frame Assembly

13 340-1848 Side Panel

14 370-1983 230/240V Blower

15 240-1953 #10-32 x 1/2" Screw (replaced 240-1207)

16 340-1886 Side Restraint Bracket, Lower

17 240-1717 Caster (replaced 370-1210)

18 240-1373 M4 0.7 Kepnut

19 230-1418 Leveler Foot (replaced 230-1181)

20 300-1263 230V Power Sequencer (replaced 370-1155)

20 300-1264 240V Power Sequencer (replaced 370-1156)

21 540-1929 230V Fan Assembly 1

21 540-1930 240V Fan Assembly 1

22 240-1655 #10-32 x 3/4" Screw

23 340-1845 Rear Panel

24 340-2047 Kick Panel

NS 230-1166 Cable Tie 5.5", Reusable

NS 230-1170 Cable Tie 10", Reusable

NS 340-2138 Ballast, 30 lbs

NS 530-1303 Remote Keyswitch Cable

800-6371 56-inch Data Center Exp Cabinet Service Manual

1. The Fans are not installed in Expansion Cabinets built after June 1993 unless a Front Load Tape

Drive is ordered as a factory installed option. The Fans were replaced by Blower 370-1983 in

July 1995.




960

76-inch Expansion Cabinet


180-1149 32Amp IEC-309 AC Receptacle (240V)

300-1011 AC Power Sequencer (115V)



340-0530 19" Logic Enclosure Support Rail Bracket (obsolete)

340-1283 19" Logic Enclosure Support Rail Assembly (obsolete)

340-1284 Keyswitch Panel, 7" x 19" (obsolete)

340-1285 Panel, 7" x 19"

340-1286 Panel, 3.5" x 19"

340-1287 Panel, 24.5" x 19"

340-1441 Keyswitch Panel, 1.5" x 19"

340-1442 Tape Drive Filler Panel, 1.5" x 19"

340-1485 19" Logic Enclosure Filler Panel, xxx x 19"

340-1487 Rear Panel with Cable Cutout, 22.7" x 19"

340-1489 Panel, 1.5 x 19"

340-1490 Panel, 10.5" x 19"

340-1522 19" Logic Enclosure Support Rail (obsolete)

340-1554 Panel, 19.6" x 19"

340-1595 Perforated Panel, 20" x 19"

340-1597 Panel, 5.25 x 19"

340-1662 892MB Disk Drive Front Panel

340-1700 Front Panel, 3.5" x 19" x 40 mm

340-1701 Front Panel, 10.5" x 19" x 40 mm

340-1715 Filler Panel for 340-1662

370-1027 AC Power Sequencer (230V) (obsolete)

370-1045 Blower Assembly

370-1053 76" Rack with Rear Door

370-1105 76" Rack without Rear Door




530-1298 AC Power Cord, Fan Assembly (115V)

530-1303 Keyswitch Cable, 2.75M


530-1343 AC Power Cord, 19" Logic Enclosure (240V) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0064d.htm (1 von 2) [25.04.2002 16:06:54]



530-1346 AC Power Cord, Fujitsu M2444AC Tape Drive (240V)

530-1347 AC Power Cord, Fujitsu M2361A Disk Drive (240V)



530-1350 AC Power Cord, CDC 92181 Tape Drive (230V)

530-1351 AC Power Cord, 19" Logic Enclosure (230V)

540-1285 Keyswitch Assembly

540-1428 AC Fan Assembly (115V)

340-1491 Fan Bracket

370-0550 AC Fan (115V)



370-1124 AC Fan (230V)



370-1124 AC Fan (240V)

540-1585 19" Logic Enclosure Support Rail Assembly

340-1583 19" Logic Enclosure Support Rail Bracket

340-1584 19" Logic Enclosure Support Rail

560-1113 19" Logic Enclosure Mounting Hardware Kit



Sun4/II: Parts - Removable Media Options - Contents

Removable Media Options

Options 558 / 559

Desktop SunCD Pack

Option 660

150MB Tape Desktop Backup Pack

Options 680 / 682 / 683 / 684 / 685

Front-Load 1/2" Tape Drive


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ce.htm [25.04.2002 16:06:59]

Sun4/II: Parts - Removable Media Options - Desktop SunCD Pack

558 559

SunCD CD-ROM SunCD CD-ROM

Desktop SunCD Pack


1 540-1778 Cover Assembly, Tape and CD-ROM

3

4

2

3

NS

NS

540-1978

150-1557

150-2049

540-1802

150-1174

340-2839

Fan/SCSI Connector/Address Select FRU Assembly

Address Select Switch (obsolete)

Address Select Switch

Fan Assembly

2A Subminiature Fuse

Fan EMI Gasket http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00680.htm (1 von 2) [25.04.2002 16:07:09]

Sun4/II: Parts - Removable Media Options - Desktop SunCD Pack

5

6

8

9

10

11

11

NS

7

7

7

540-1773

330-1214

Base Assembly

Rubber Foot

300-1037

300-1090

300-1105

35 Watt Power Supply (obsolete) 1

35 Watt Power Supply (obsolete)

44 Watt Power Supply

540-1931

370-1312

340-1967

530-1454

530-1825

240-1141

SunCD CD-ROM Assembly

Sony CDU-8012 CD-ROM

Drive Bracket

Address Select Switch Cable, 5.25"

Address Select Switch Cable, 8.5"

#6-32 x 1/4" Screw

NS 150-1346 External Terminator, 50-Pin SCSI-2

NS 150-1785 External Active Terminator, 50-Pin SCSI-2

NS 530-1434 External Cable, 50-Pin SCSI-2 to SCSI-2, 45 cm

NS 530-1435 External Cable, 50-Pin SCSI-2 to DD-50SA, 2.0M






NS 530-1836 External Cable, 50-Pin SCSI-2 to SCSI-2, 2.0M


NS

NS

555-1154

370-1316

Caddy 3-Pack

Caddy

NS 800-4895 Desktop Storage Pack Field Service Manual

1. Power Supply 300-1037 does not have IEC950 or UL1950 approval. Do NOT install 300-1037 into options manufactured after March 1991.



Sun4/II: Parts - Removable Media Options - 150MB Tape Desktop Backup Pack

660

150MB Tape

Desktop Backup Pack


1 540-1778 Tape Drive Cover Assembly

2

3

4

NS

540-1776

150-1338

540-1802

150-1174

Fan/SCSI Connector/Address Select Assy (obs)


Fan Assembly

2A Subminiature Fuse http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00681.htm (1 von 2) [25.04.2002 16:07:18]

Sun4/II: Parts - Removable Media Options - 150MB Tape Desktop Backup Pack

3

4

2

3

NS

NS

5

6

540-1978

150-1557

150-2049

540-1802

150-1174

340-2839

Fan/SCSI Connector/Address Select Assembly


Address Select Switch

Fan Assembly

2A Subminiature Fuse

Fan EMI Gasket

7

7

7

540-1773

330-1214

Base Assembly

Rubber Foot

300-1037

300-1090

300-1105

35 Watt Power Supply (obsolete) 1

35 Watt Power Supply (obsolete)


8 370-1218 150MB Tape Drive, QIC-150, Archive 2150S

9 340-1967 Tape Drive Bracket

10 530-1454 Address Select Switch Cable, 5.25"

10 530-1825 Address Select Switch Cable, 8.5"

NS 240-1141 #6-32 x 1/4" Screw



NS 530-1434 External Cable, 50-Pin, SCSI-2 to SCSI-2, 45 cm

NS 530-1508 External Cable, SCSI-2 to SCSI-2, 80 cm




NS 800-4895 Desktop Storage Pack Field Service Manual

1. Power Supply 300-1037 does not have IEC950 or UL1950 approval. Do NOT install 300-1037 into options manufactured after March 1991.



Sun4/II: Parts - Removable Media Options - Front-Load 1/2" Tape Drive

680 682 683 684 685

TableTop 56" Rack

56" Exp Rack

1st Tape

56" Exp Rack

2nd Tape

SC2000

56" Exp Rack

8

9

6

7

9

9

CODE SUN PART# HP PART#

1

1

DESCRIPTION

811-1236 88780-67707 Front Bezel Assembly 1

811-1236 88780-68207 Front Bezel Assembly 2

4

5

2

3

811-1210

811-1227

811-1228

811-1242

07980-44111 Power Switch Button

07980-61616 Power Switch Assembly

07980-65000 Door Latch Assembly

07980-69025 Power/Motor Drive Board

811-1245

811-1241

811-1229

140-1011

140-1002

140-1039

07980-60043 Fan

88780-69015 Single Ended I/O Board

07980-67919 Power Module

None

None

None

6.0A Fuse, .25x1.25" (115V)

3.15A Fuse, 5x20 mm (240V)

3.0A Fuse, .25x1.25" (230V) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00682.htm (1 von 5) [25.04.2002 16:07:34]


13

13

14

15

10

11

12

16

17

18

19

20

21

21

22

23

24

811-1235 3110-0178 Cover Hinge

811-1231 1390-0776 Cover Latch

811-1215 07980-60041 Speed Sensor Assembly

811-1218 07980-60052 Takeup Hub Assembly, Plastic

811-1218 07980-60152 Takeup Hub Assembly, Aluminum

811-1214 07980-60040 EOT/BOT Sensor Assembly

811-1216 07980-60045 Arm Buffer Assembly

811-1209 07980-21701 Buffer Arm Bearing (Roller Guide)

811-1233 1460-2180 Buffer Spring

811-1219 07980-60053 Supply Hub Assembly

370-1276 07980-66531 Read/Write/Format Board

370-1277 07980-66503 Drive Controller Board

370-1279 07980-66514 Data Buffer Board, 512KB Buffer 3

370-1279 07980-66534 Data Buffer Board, 1MB Buffer 3

811-1232 1420-0314 3V Lithium Battery 3

811-1211 07980-60000 Mother Board PCA

811-1212 07980-60008 Display (Front Panel PCA)

1. The latch release swings out to the right.

2. The latch release pulls straight out.

3. The battery is not replaceable on Data Buffer Boards manufactured after approximately January

1990.



NS

NS

NS

NS

NS

NS

NS

NS

NS

COD E SUN PART# HP PART#

25 811-1230

DESCRIPTION

07980-86500 Blower Motor

26

27

811-1217

811-1226

07980-60050 Takeup/Supply Reel Motor

07980-60144 Hub Lock Assembly

28

29

30

31

811-1238

811-1237

811-1213

811-1292

07980-60042 Head Plate Assembly

07980-60051 Tape Displacement Unit

07980-60009 Tape Sensor Assembly

9100-4637 Transformer

811-1220

811-1221

811-1222

811-1223

811-1224

811-1225

811-1234

811-1240

811-1243

07980-60062 Speed Sensor Cable

07980-60064 Front Panel Cable

07980-60067 Interface Cable

07980-60070 Cable Harness

07980-60071 Read Head Cable

07980-60072 Write Head Cable

3101-2923 Door Microswitch

07980-60065 Motor Control Cable

88780-60290 Firmware Kit (obsolete) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00682.htm (3 von 5) [25.04.2002 16:07:34]


NS

NS

NS

811-1243 88780-60082 Firmware Kit (not qualified)

811-1243 88780-6018 2 Firmware Kit 1

811-1244 07980-60048 NRZI Speed Sensor

1. Firmware Kit 88780-60182 includes Drive Controller firmware level 6.76, Buffer firmware level 6.77, and SCSI firmware level 6.62.


180-1097 5V Power Cord, IEC 320/CEE 22 to NEMA 5-15P

180-1189 230V Power Cord, IEC 320/CEE 22 to NEMA 6-15P

180-1190 240V Power Cord, IEC 320/CEE 22 to Reverse IEC 320

230-1166 Tie Wrap, 5.5"

230-1177 Cable Tie Clip

240-1207 10-32 x 1/2" Screw

250-1018 Rubber Stop Bumper

260-4191 Logo

330-1312 Shipping Bracket, 56" Rack (obsolete)




340-2288 Shipping Bracket, Outer Side, 56" Rack

340-2289 Shipping Bracket, Inner Side, 56" Rack

370-1254 Slide Rails

530-1501 Data Cable, DD-50SA to Centronics, 2.0M

530-1502 Data Cable, Centronics to Centronics, 1.5M,

530-1503 Data Cable, 50-Pin SCSI-2 to Centronics, 2.0M


530-1900 Data Cable, 50-Pin SCSI-2 to Centronics, 4.0M

599-1684 115V Tabletop Tape Drive Assembly

599-1685 240V Tabletop Tape Drive Assembly

140-1011 6.0A Fuse, .25x1.25" (115V)

140-1002 3.15A Fuse, 5x20 mm (240V)

150-1407 SCSI Terminator, Centronics


540-1821 Tabletop Tape Drive without Fuse and Labels

540-1897 230V Rackmount Tape Drive Assembly

540-1898 240V Rackmount Tape Drive Assembly

140-1002 3.15A Fuse, 5x20 mm (240V)

140-1039 3.0A Fuse, .25x1.25" (230V)

150-1407 SCSI Terminator, Centronics http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00682.htm (4 von 5) [25.04.2002 16:07:34]



540-1823 Rackmount Tape Drive without Fuse and Labels



Sun4/II: Parts - Disk Options - Contents

Disk Options

Options 526 / 527 / 530 / 539

327MB Disk External Storage Module

Options 561 / 563 / 565 / 566

669MB Disk External Storage Module

Options 706 / 707 / 709 / 710

1.2GB IPI-2 Disk Subsystem

Options 716 / 717 / 719 / 720

911MB IPI-2 Disk Subsystem

Options 726 / 727 / 728

1.3GB IPI-2 Disk Subsystem

Options 741A / 742A / 743A / 744A / 745A

1.2GB IPI Disk Expansion Pedestal

Options 741L / 742L / 743L / 744L / 745L

911MB IPI Disk Expansion Pedestal

Options 750 / 754 / 756

1.3GB SCSI Expansion Pedestal


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004cb.htm [25.04.2002 16:07:39]

Sun4/II: Parts - Disk Options - External Storage and External Expansion Modules

526 527 530 539

327MB Disk 327MB Disk Expansion Two 327MB Disks

327MB Disk

150MB Tape

External Storage and External

Expansion Modules


150-1556 SCSI ID Select Switch

300-1031 120 Watt Power Supply

330-1146 Disk Drive Mounting Bracket

330-1158 Disk Drive Removal Handle

350-1006 Top Cover

350-1010 Left Side Cover

350-1011 Front Bezel

350-1013 Right Side Cover

350-1117 Rear Bezel

370-1203 DC6150 QIC-150 1/4" Tape Cartridge

370-1246 150MB Tape Drive, Full-Height, QIC-150

530-1249 External SCSI Cable, DD-50SA to DD-50SA, 1.0M



530-1365 External SCSI Cable, DD-50SA to DD-50SA, 41 cm

530-1381 External Terminator, 50-Pin DD-50SA

530-1409 Internal SCSI Ribbon Cable (obsolete)



530-1792 External Cable, 50-Pin SCSI-2 to DD-50SA, 2.0M, Ferrites


530-1461 1/4" Tape Drive SCSI Adapter Cable

530-1618 Internal SCSI Cable, 95 cm

530-1659 SCSI ID Select Switch Cable

555-1005

330-1146

330-1158

370-1153

327MB SCSI Disk Drive FRU Assembly

Mounting Bracket

Drive Removal Handle

327MB Disk Drive, Imprimis/CDC 77777107

570-1042 Full-Height Peripheral Front Filler Panel

814-5036 Replacing Components of Sun ESM & EEM Storage Units http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00622.htm (1 von 2) [25.04.2002 16:07:49]

Sun4/II: Parts - Disk Options - External Storage and External Expansion Modules



Sun4/II: Parts - Disk Options - External Storage and External Expansion Module

561 563 565 566

669MB Disk Two 669MB Disks

669MB Disks

150MB Tape

669MB Disk

2.3GB Tape

External Storage and External

Expansion Module


150-1556 SCSI ID Select Switch

300-1031 120 Watt Power Supply

330-1146 Disk Drive Mounting Bracket

330-1158 Disk Drive Removal Handle

340-2359 Disk Drive Mounting Bracket, Right

340-2360 Disk Drive Mounting Bracket, Left

350-1006 Top Cover

350-1010 Left Side Cover


350-1013 Right Side Cover

350-1117 Rear Bezel

370-1203 DC6150 QIC-150 1/4" Tape Cartridge

370-1246 150MB Tape Drive, Full-Height, QIC-150

370-1297 2.3GB 8 mm Tape Drive, Full-height

370-1298 8 mm Tape Cartridge

370-1318 8 mm Cleaning Cartridge

370-1319 669MB Disk Drive, Micropolis 1588-15 with Bezel

370-1319 669MB Disk Drive, Maxtor XT-8760S with Bezel 1

370-1326 669MB Disk Drive, Micropolis 1588-15 without Bezel

370-1326 669MB Disk Drive, Maxtor XT-8760S without Bezel 1




530-1365 External SCSI Cable, DD-50SA to DD-50SA, 41 cm

530-1381 External Terminator, 50-Pin DD-50SA





530-1461 1/4" Tape Drive SCSI Adapter Cable

530-1618 Internal SCSI Cable, 95 cm http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00623.htm (1 von 2) [25.04.2002 16:07:53]

Sun4/II: Parts - Disk Options - External Storage and External Expansion Module

530-1659 Address Select Switch Cable, 2.54 mm Pin Spacing

570-1042 Full-Height Peripheral Front Filler Panel

814-5036 Replacing Components of Sun ESM and EEM Storage Units

1. The Maxtor drive does not fit into the lower drive position of External Storage Modules manufactured prior to October 1990. Remove the vertical stop block with10-Inch End Cutter,

250-1074-01.



Sun4/II: Parts - Disk Options - 1.2GB IPI-2 Disk Subsystem

706 707 709 710

1.2GB Disk 2.1.2GB Disks 4 1.2GB Disks 8 1.2GB Disks

1.2GB IPI-2 Disk Subsystem


540-1770 IPI Drive, Power Supply, and Tray Assembly

1 300-1041 205W Power Supply

2 370-1263 DC Harness

3 240-1603 Cable Clamp

4 240-1185 #6-32 x 1/4" Screw

5 370-1262 Operator Panel Harness

6 240-1035 Lock Washer, #6

7 240-1602 Cable Clamp http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00624.htm (1 von 2) [25.04.2002 16:08:04]


8 370-1350 Air Baffle

9 370-1187 1.2GB Disk, Seagate 97209-12G, PA8R2

10 240-1185 #6-32 x 1/4" Screw (use 7/64" Hex Screwdriver)

11 250-1013 Ground Strap

12 240-1186 #6-32 x 3/8" Screw

13 240-1595 Power Cord Clamp

14 180-1185 AC Power Cord, 572 mm


16 340-1854 Tray


18 250-1016 Filter

19 330-1224 Operator Panel Mounting Bracket

20 330-1226 Operator Panel Shield

21 370-1221 Operator Panel

22 330-1225 Operator Panel Cover

23 240-1601 #6-32 x 1/4" Screw (use 2 mm Hex Screwdriver)


NS 180-1183 AC Power Cord, 'Y' (230V)


NS 340-1853 Dual Drive Tray (obsolete)

NS 340-1855 Tray Slide, Right (obsolete)

NS 340-1856 Tray Slide, Left (obsolete)

NS 340-1891 Tray Spacer

NS 340-2296 Dual Drive Tray

NS 370-1220 IPI Drive Terminator

NS 530-1351 AC Power Cord (230V)


NS 530-1487 IPI Drive I/O Cable, 8.0M (obsolete)

NS 530-1488 IPI Drive I/O Cable, 1.0M


NS 530-1536 IPI Drive I/O Cable, 450 mm



NS None #6-32 x 1/4" Screw (use T15 Torx Screwdriver)

NS 370-1330 Connector Assembly (use 7/64" Hex Screwdriver)



Sun4/II: Parts - Disk Options - 911MB IPI-2 Disk Subsystem

716 717 719 720

911MB Disk 2 911MB Disks 4 911MB Disks 8 911MB Disks

911MB IPI-2 Disk Subsystem


540-2005 IPI Drive, Power Supply, and Tray Assembly

1 300-1074 215 Watt Power Supply


3 240-1603 Cable Clamp

4 240-1185 #6-32 x 1/4" Screw

5 370-1262 Operator Panel Harness

6 240-1035 #6 Lock Washer

7 240-1602 Cable Clamp http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00625.htm (1 von 2) [25.04.2002 16:08:19]

Sun4/II: Parts - Disk Options - 911MB IPI-2 Disk Subsystem

8 370-1350 Air Baffle

9 370-1351 911MB Disk, Seagate 97229-11G, PA8Y2



12 240-1186 #6-32 x 3/8" Screw

13 240-1595 Power Cord Clamp

14 180-1185 AC Power Cord, 572 mm


16 340-1854 Tray


18 250-1016 Filter

19 330-1224 Operator Panel Mounting Bracket

20 330-1226 Operator Panel Shield

21 370-1355 Operator Panel

22 330-1225 Operator Panel Cover

23 240-1601 #6-32 x 1/4" Screw (use 2 mm Hex Screwdriver)




NS 340-1853 Dual Drive Tray (obsolete)

NS 340-1855 Tray Slide, Right (obsolete)

NS 340-1856 Tray Slide, Left (obsolete)

NS 340-1891 Tray Spacer

NS 340-2296 Dual Drive Tray

NS 370-1220 IPI-2 Disk Terminator









NS None #6-32 x 1/4" Screw (use T15 Torx Screwdriver)

NS 370-1330 Connector Assembly (use 7/64" Hex Screwdriver)




726 727 728

2 1.3GB Disks

1 Tray

4 1.3GB Disks

1 Tray

1.3GB Disk

1.3GB IPI-2 Disk Subsystem


1 340-2461 Chassis Enclosure

2 None #8-32 x 1/4" Pan Head Screw, Slide Rail to Chassis

3 240-1372 M4 0.7 x 10 mm Screw

4 230-1170 10" Tiestrap

5 150-1557 Address Select Switch

6 230-1256 Nylon Standoff, M4 x 25 mm

7 340-2466 Power Supply Mounting Bracket

8 240-1373 M4 Nut

9 501-1827 Remote LED Display Panel

10 530-1768 Address Select Switch Cable http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00626.htm (1 von 2) [25.04.2002 16:08:30]


11 540-2125 3-Fan Tray Assembly, 45 CFM

12 530-1764 DC Wire Harness

13 540-2126 DC Fan Assembly, 45 CFM



15 130-1080 Jack Socket

16 240-1872 Jackscrew

17 530-1753 Internal IPI I/O Cable

18

18

370-1385

370-1385

-01 Slide Rail Set, Inner 651.2 mm, Outer 742.7 mm

-03 Slide Rail Set, Inner 717.3 mm, Outer 742.7 mm

19 340-2465 Chassis Cover

NS None Cross-Drilled Top Cover Screw, M4 0.7 x 10 mm

NS None Top Cover Screw Retaining Clip

NS 240-1207 #10-32 x 1/2" Screw, Slide Rail to Rack

NS 370-1220 IPI Terminator

NS 530-1343 AC Power Cord, 240V

NS 530-1351 AC Power Cord, 230V

NS 530-1487 External IPI I/O Cable, 8.0M (obsolete) 1

NS 530-1518 External IPI I/O Cable, 2.0M (obsolete) 1

NS 530-1536 External IPI I/O Cable, 45 cm

NS 530-1788 External IPI I/O Cable, 2.0M

NS 530-1789 External IPI I/O Cable, 8.0M

NS

NS

NS

NS

NS

540-2127

370-1378

340-2464

330-1400

240-1185

1.3GB Disk Drive FRU

1.3GB Disk Drive, Seagate 975002-005, PA4F2

Disk Drive Mounting Bracket

Disk Drive Handle

#6-32 x 1/4" Screw, Disk Drive to Bracket

800-6676 1.3GB Tray and Disk Drive Install/ServiceManual

1. IPI Cables without toroids, 530-1518 and 530-1487, can be used with the Sun-4/490.



Sun4/II: Parts - Disk Options - Sun Expansion Pedestal

741A 742A 743A 745A 744A

1.2GB Disk 2 1.2GB Disks 3 1.2GB Disks 4 1.2GB Disks

1.2 GB Disk

Standalone

Sun Expansion Pedestal

CODE PART #

NS

NS

1

NS

NS

NS

NS

NS

340-2188

340-2208

540-1926

370-1314

340-2300

180-1486

240-1207

250-1070

DESCRIPTION

Rear Panel without Cables

Filler Panel

IPI8-1000 3MB/Sec Disk Drive FRU Assembly

1.2GB Disk Drive, Seagate 97209-12G, PA8R2 1

Disk Mounting Cradle

Front Ground Strap

#10-32 x 1/2" Drive Mounting Screw

Rear Ground Strap

NS 340-1898 Top Cover

NS 330-1192 Disk Bezel Insert

NS 540-1749 Rear Bumper Assembly

NS 540-1846 Side Panel Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00627.htm (1 von 2) [25.04.2002 16:08:34]


NS 540-1847 Rear Bezel Assembly

NS 540-1939 Front Panel and Bumper Assembly








2

NS

NS

540-1765

340-2050

501-1531

LED/Switch Assembly

Switch Panel

LED/Switch PCB

3

NS

NS

NS

540-1748

330-1212

330-1213

340-1936

Remote Switch Assembly

Switch

Push Block

Switch Housing

4 530-1495 LED/Switch DC Harness

5 340-2129 Caster

6 240-1372 M4 0.7 x 10 mm Screw


8 300-1052 820W Power Supply (obsolete) 2

8 300-1075 840W Power Supply

NS 530-1619 System Grounding Cable, 2.0M

NS 340-2262 Cable Restraint Bracket

NS 230-0203 4" Tiestrap

NS 230-1188 6" Tiestrap, Snap-in

NS 800-3257 Sun Expansion Pedestal Field Service Manual

1. Do NOT install Disk Drive 370-1187 in the Sun Expansion Pedestal

2. Power Supply 300-1052-05 does not support the 1.2GB Disk Drive.




741L 742L 743L 744L 745L

911MB Disk 2 911MB Disks 3 911MB Disks 4 911MB Disks 911MB Disk

Standalone

Sun Expansion Pedestal

CODE PART #

NS

NS

1

NS

NS

NS

NS

NS

340-2188

340-2208

DESCRIPTION

Rear Panel without Cables

Filler Panel

540-2008

370-1352

340-2300

180-1486

240-1207

250-1070

IPI8-1000/2HP 6MB/Sec Disk Drive FRU Assembly

911MB Disk Drive, Seagate 97209-11G, PA8Y2 1

Disk Mounting Cradle

Front Ground Strap

#10-32 x 1/2" Drive Mounting Screw

Rear Ground Strap

NS 340-1898 Top Cover

NS 330-1192 Disk Bezel Insert

NS 540-1749 Rear Bumper Assembly

NS 540-1846 Side Panel Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00628.htm (1 von 2) [25.04.2002 16:08:42]


NS 540-1847 Rear Bezel Assembly

NS 540-1939 Front Panel and Bumper Assembly








2

NS

NS

540-1765

340-2050

501-1531

LED/Switch Assembly

Switch Panel

LED/Switch PCB

3

NS

NS

NS

540-1748

330-1212

330-1213

340-1936


Switch

Push Block

Switch Housing

4 530-1495 LED/Switch DC Harness

5 340-2129 Caster

6 240-1372 M4 0.7 x 10 mm Screw


8 300-1075 840W Power Supply 2


NS 340-2262 Cable Restraint Bracket

NS 230-0203 4" Tiestrap

NS 230-1188 6" Tiestrap, Snap-in

NS 800-3257 Sun Expansion Pedestal Field Service Manual

1. Do NOT install Disk Drive 370-1351 in the Sun Expansion Pedestal.

2. Power Supply 300-1052 does not support the 911MB Disk Drive.



Sun4/II: Parts - Disk Options - SCSI Expansion Pedestal

750 754 756

2 1.3GB Disks

1 Tray

4 1.3GB Disks

8 mm Tape

2 1.3GB Disks

Expansion Tray

SCSI Expansion Pedestal


1 540-1846 Side Cover



3 340-1898 Top Cover

4 340-2534 Front EMI Cover, without Switch Assembly

5 340-2292 Blank EMI Cover Filler Panel http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00629.htm (1 von 2) [25.04.2002 16:08:53]

Sun4/II: Parts - Disk Options - SCSI Expansion Pedestal

6 330-1192 Blank Bezel Insert

7 330-1210 Front Bezel Half-Height Insert

7 330-1284 Front Bezel Full-Height Insert

8

NS

NS

540-1939

240-0558

240-0557

Front Bezel Assembly

Miniball Receptacle

Miniball Fastener

9

NS

NS

NS

NS

540-1765

501-1531

540-2136

330-1373

340-2491

LED/Switch Assembly

LED/Switch PCB


Switch

Switch Bracket

10 340-2444 Peripheral Mounting Bracket

11 370-1377 1.3GB Disk Drive, Seagate 976002-012, PA4E1

11 370-1377 1.3GB Expansion Disk Drive, Option 572

12 340-2129 Caster


NS 340-2535 Rear EMI Cover

NS 340-2543 Rear EMI Cover Filler Panel

NS 370-1297 2.3GB 8 mm Tape Drive, Full-Height, Option 802

NS 370-1347 SunCD CD-ROM, Half-Height, Option 559


NS 530-1675 Peripheral Tray DC Harness

NS 530-1676 Internal SCSI Cable, 1670 mm

NS 530-1793 External Cable, 50-Pin SCSI-2, 80 cm, Ferrites

NS 530-1811 DC Harness, Power Supply to Right Side

NS 530-1824 LED/Switch DC Harness, Power Supply to Switch

NS 530-1836 External Cable, 50-Pin SCSI-2, 2.0M, Ferrites

NS 530-1841 DC Harness, Power Supply to Fans and Left Side

NS 530-1842 CD-ROM Grounding Cable

NS 530-1852 External Cable, 50-Pin SCSI-2, 4.0M, Ferrites

NS 540-1749 Rear Bumper

NS 540-1847 Rear Bezel

NS 540-2157 Three Fan Assembly, 45 CFM each

800-6402 Sun SCSI Expansion Pedestal Service Manual

800-7286 Sun SCSI Expansion Pedestal Service Manual



Sun4/II: Parts - System - Contents

System


Sun-4/110/310

Sun-4/150/350

Sun-4/260/360

Sun-4/280/380

Sun-4/330

Sun-4/370/470

Sun-4/390/490


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c8.htm [25.04.2002 16:08:57]

Sun4/II: Parts - System - Sun-4/110/310

Sun-4/110/310

3-Slot VMEbus Logic Enclosure

PART #

140-1019 Fuse, 15A (115V)

140-1030 Fuse, 6.3A (240V)

150-1042 Fusecarrier (115V)

DESCRIPTION


180-1010 AC Power Cord, Coiled, AC Output Receptacle to Monitor

180-1097 AC Power Cord (115V)

180-1117 AC Power Cord, AC Output Receptacle to Monitor


240-1368 M6 1.0 x 16 mm Screw, Side Cover

260-4443 Sun-4/310 Logo

300-1022 325 Watt Power Supply, Summit (replaced by 300-1093)

300-1022 325 Watt Power Supply, Brown (obsolete)

300-1093 325 Watt Power Supply, Summit

330-1067 End Panel, 42 cm X 11 cm


330-1071 Side Panel, 42 cm X 59 cm

330-1089 Side Panel Screw Cover

330-1144 Backplane Shield

340-1545 Air FIlter Assembly

370-1106 AC Switch and Fuse (obsolete)

370-1178 AC Switch, Fuse, and Filter Assembly /TD>


540-1384 DC Fan Tray and Power Supply Module Assembly (115V)

540-1418 Power Supply Module Assembly (115V)

540-1419

501-1193

540-1455

DC Fan Tray Assembly, 4 Fans

Fan Controller PCB

DC Fan Assembly, 26 CFM

540-1535 3-Slot Foot Assembly

540-1541 Power Supply Module Assembly (240V)


800-2126 Field Service Manual for the Sun 3-Slot Logic Enclosure


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068a.htm [25.04.2002 16:09:05]


Sun-4/150/350


PART #

140-1019 Fuse, 15A (115V)

140-1030 Fuse, 6.3A (240V)


DESCRIPTION


150-1217 AC Line Filter (obsolete) 1

180-1010 AC Power Cord, Coiled, AC Output Receptacle to Monitor


180-1117 AC Power Cord, AC Output Receptacle to Monitor


240-1368 M6 1.0 x 16 mm Screw, Side Cover

330-1068 End Panel, 42 cm X 17 cm


330-1071 Side Panel, 42 cm X 59 cm

330-1089 Side Panel Screw Cover

330-1143 Backplane Shield

340-1547 Air FIlter Assembly

370-1106 AC Switch and Fuse (obsolete) 1

370-1178 AC Switch, Fuse, and Filter Assembly 1

501-1128 6-Slot VMEbus Backplane

530-1352 AC Harness, AC Switch to Line Filter (obsolete) 1

530-1353 AC Harness, Line Filter to Power Supply (obsolete) 1


540-1409

501-1233

540-1471

DC Fan Tray Assembly

Fan Controller PCB


540-1410

300-1020

340-1454

Power Supply Module Assembly (115V)


Power Supply Cover

540-1475 6-Slot Foot Assembly

800-1944 Field Service Manual for the Sun 6-Slot Logic Enclosure

1. When AC Switch 370-1106 is replaced with AC Switch 370-1178, remove AC Line

Filter150-1217, AC Wire Harness 530-1352, and AC Wire Harness 530-1353.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068b.htm [25.04.2002 16:09:09]


Sun-4/260/360


PART #

140-1019 Fuse, 15A (115V)

DESCRIPTION

140-1030 Fuse, 6.3A (240V)

150-1018 AC Power Switch, Illuminated (obsolete)

150-1216 AC Power Switch, Non-Illuminated

150-1041 Fuse Holder (115V)


150-1051 Fuse Carrier (240V)

150-1129 AC Line Filter



240-1048 Caster

260-4442 Sun-4/360 Logo


330-1076 Backplane Cable Shield

340-1138 Top Cover

340-1261 Side Panel, Right

340-1262 Side Panel, Left

370-1086 12-Slot Cardcage

501-1092 12-Slot VMEbus Backplane, Pressfit (obsolete)


530-1134 SCSI Bus Cable, Backplane to SCSI Tray

530-1135 DC Harness, Power Supply DC Harness to SCSI Tray

530-1230 AC Receptacle

530-1231 AC Harness, AC Receptacle to AC Filter

530-1207 AC Harness, AC Filter to Fuse to Switch to Power Supply

800-1525 Field Service Manual for the Sun-3/260 Workstation

Fan Assemblies


540-1510

530-1171

530-1322

DC Fan Assembly, 71 CFM, Upper Chassis

DC Harness, Power Supply Harness to Upper Fans (obs)

DC Harness, Power Supply Harness to Upper Fans http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068c.htm (1 von 3) [25.04.2002 16:09:16]


540-1555

540-1510

530-1357

6-Fan Tray Assembly (obsolete)


DC Harness, Fan Tray

540-1581

540-1510

530-1357

6-Fan Tray Assembly, Low Profile, No Fingerguards (obs)



540-1584

540-1572

530-1357

6-Fan Tray Assembly, Low Profile, Individual Fingerguards

DC Fan Assembly, 71 CFM, Low Profile


540-1596

540-1572

530-1357

6-Fan Tray Assembly, Low Profile, Full Screen

DC Fan Assembly, 71 CFM, Low Profile


Power Supplies


300-1024

530-1206

530-1201

530-1324

850 Watt Power Supply, Fuji Electrochemical

DC Harness, +5Vdc

DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc (obsolete)

DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc

300-1043

530-1578

530-1581


DC Harness, +5Vdc


Tape and Disk Drive Options


370-1011

370-1037

370-1112

370-1112

530-1141

Sysgen SC4000 Tape Controller

45/60MB 1/4" Tape Drive, Wangtech 5099EG11 (obsolete)

45/60MB 1/4" Tape Drive, QIC-11/24, Wangtech 5099EG11

45/60MB 1/4" Tape Drive, QIC-11/24, Archive 5945L-2

Tape Command Cable, Sysgen SC4000 to Tape Drive

370-1061

370-1235

370-1076

370-1103

370-1103

530-1141

Emulex MT02 Tape Controller

Emulex MT02 Tape Controller

45/60MB 1/4" Tape Drive, Wangtech 5099EN24 (obsolete)

45/60MB 1/4" Tape Drive, QIC-11/24, Wangtech 5099EN24

45/60MB 1/4" Tape Drive, QIC-11/24, Archive 5945C

Tape Command Cable, Emulex MT02 to Tape Drive http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068c.htm (2 von 3) [25.04.2002 16:09:16]


370-1010

370-1034

370-1034

530-1134

530-1135

530-1142

530-1145

530-1157

Adaptec ACB-4000 SCSI Disk Controller

71MB Disk Drive, Micropolis 1325

71MB Disk Drive, Fujitsu M2243AS

SCSI Bus Cable, Backplane to SCSI Tray

DC Harness, Power Supply DC Harness to SCSI Tray

Disk Data Cable, 39 cm, LUN 0


Disk Command Cable, Dual Disk

370-0552

370-1236

370-0551

370-0551

370-1133

530-1134

530-1135

530-1142

530-1145

530-1157

Emulex MD21 SCSI Disk Controller

Emulex MD21 SCSI Disk Controller

141MB Disk Drive, Micropolis 1355

141MB Disk Drive, Toshiba MK156

327MB Disk Drive, Micropolis 1558-15

SCSI Bus Cable, Backplane to SCSI Tray

DC Harness, Power Supply DC Harness to SCSI Tray



Disk Command Cable, Dual Disk




Sun-4/280/380


PART #

140-1019 Fuse, 15A (115V)

140-1026 Fuse, 6A (230V)

140-1030 Fuse, 6.3A (240V)

DESCRIPTION

150-1018 AC Power Switch, Illuminated (obsolete)

150-1216 AC Power Switch, Non-Illuminated

150-1041 Fuse Holder (115V)


150-1051 Fuse Carrier (240V)

150-1129 AC Line Filter


260-4441 Sun-4/380 Logo

330-1076 Backplane Cable Shield

340-1283

340-1583

340-1584

Cardcage Mounting Bracket Assembly (obsolete)

Front and Rear Angle Bracket

Side Angle Bracket

340-1685 Front EMI Cover

340-1686 Front EMI Cover

370-1086 12-Slot Cardcage

501-1092 12-Slot VMEbus Backplane, Pressfit (obsolete)


530-1230 AC Receptacle Assembly

530-1257 AC Harness, AC Receptacle to AC Filter

530-1258 AC Harness, AC Filter to Fuse to Switch to Power Supply

530-1260 Indicator Lamp, 12Vdc (obsolete)



540-1366

530-1259

530-1321

540-1129

540-1509

Fan Tray Assembly, 4 Fans

DC Harness, Fan Tray (obsolete)


DC Fan Assembly, 88 CFM (obsolete)


540-1508 Indicator Lamp, 12Vdc

540-1585 Cardcage Mounting Bracket Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068d.htm (1 von 4) [25.04.2002 16:09:26]


Power Supplies


300-1024

530-1206

530-1340

530-1222

530-1320


DC Harness, +5Vdc (obsolete)

DC Harness, +5Vdc

DC Harness, +5Vdc, -5Vdc, +12Vdc, -12Vdc (obsolete)


300-1043

530-1578

530-1580


DC Harness, +5Vdc


1/4" Tape Drive Option

PART #

230-1007 Plastic Standoff, 1.0 cm

DESCRIPTION

370-1061 Emulex MT02 Tape Controller


370-1076 45/60MB 1/4" Tape Drive, Wangtech 5099EN24 (obsolete)

370-1103 45/60MB 1/4" Tape Drive, QIC-11/24, Wangtech 5099EN24

370-1103 45/60MB 1/4" Tape Drive, QIC-11/24, Archive 5945C


530-1249 SCSI Bus Cable, SCSI Host Adapter to SCSI Tray

530-1277

140-1010

DC Harness, Emulex MT02 to Tape Drive

Fuse, 5A, +5Vdc

530-1278 SCSI Bus Cable, Rear Panel to Emulex MT02

530-1279 Tape Command Cable, Emulex MT02 to Tape Drive

813-1016 Installation and Service Manual for the Sun-3/180 Tape Drive Option

76-inch Data Center Cabinet


180-1149 32Amp IEC-309 AC Receptacle (240V)




340-0530 19" Logic Enclosure Support Rail Bracket (obsolete)

340-1283 19" Logic Enclosure Support Rail Assembly (obsolete)

340-1284 Keyswitch Panel, 7" x 19" (obsolete)

340-1285 Panel, 7" x 19"

340-1286 Panel, 3.5" x 19" http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068d.htm (2 von 4) [25.04.2002 16:09:26]


340-1287 Panel, 24.5" x 19"

340-1441 Keyswitch Panel, 1.5" x 19"

340-1442 Tape Drive Filler Panel, 1.5" x 19"

340-1485 19" Logic Enclosure Filler Panel, xxx x 19"

340-1487 Rear Panel with Cable Cutout, 22.7" x 19"

340-1489 Panel, 1.5 x 19"

340-1490 Panel, 10.5" x 19"

340-1522 19" Logic Enclosure Support Rail (obsolete)

340-1554 Panel, 19.6" x 19"

340-1595 Perforated Panel, 20" x 19"

340-1597 Panel, 5.25 x 19"

340-1662 892MB Disk Drive Front Panel

340-1700 Front Panel, 3.5" x 19" x 40 mm

340-1701 Front Panel, 10.5" x 19" x 40 mm

340-1715 Filler Panel for 340-1662


370-1045 Blower Assembly

370-1053 76" Rack with Rear Door

370-1105 76" Rack without Rear Door





530-1303 Keyswitch Cable, 2.75M








530-1350 AC Power Cord, CDC 92181 Tape Drive (230V)


540-1285 Keyswitch Assembly



370-0550 AC Fan (115V)



370-1124 AC Fan (230V)

540-1568 AC Fan Assembly (240V) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068d.htm (3 von 4) [25.04.2002 16:09:26]



370-1124 AC Fan (240V)

540-1585 19" Logic Enclosure Support Rail Assembly

340-1583 19" Logic Enclosure Support Rail Bracket

340-1584 19" Logic Enclosure Support Rail

560-1113 19" Logic Enclosure Mounting Hardware Kit



Sun4/II: Parts - System - Sun-4/330

Sun-4/330



NS 260-3617 SPARCstation 330 Logo

NS 260-3818 SPARCserver 330 Logo

1 330-1178 Rear Cover

NS 330-1180 Cable Retainers

NS

NS

3

3

4

2 540-1760 Fan and Bracket Assembly

530-1465

530-1468

540-2029

540-1788

540-1811

DC Harness, Power Supply to Peripherals & Fans 1

Fan Harness 1

Fan Assembly, Variable Speed, 105 CFM

Fan Assembly, 100 CFM (obsolete)

AC Receptacle

5 530-1470 AC Input Harness http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068e.htm (1 von 3) [25.04.2002 16:09:33]


10

NS

10

NS

6

NS

NS

NS

340-1772

501-1432

501-1416

120-1608

SCSI Terminator Access Panel

SCSI IN Terminator PCB

SCSI OUT Terminator PCB

220/330 Terminator

7 540-1789 Top Cover Assembly

8 530-1469 AC Harness, Internal 2

9

NS

540-1787

340-2500

Front Cover Assembly

Front Cover Air Baffle

540-1758

340-1783

Upper Drive Tray Assembly (obsolete) 3

Drive Tray

11

NS

540-2133

340-2497

Upper Drive Tray Assembly

Drive Tray

540-1757

340-1782

Lower Drive Tray Assembly (obsolete) 3

Drive Tray

11

NS

540-2132

340-2498

Lower Drive Tray Assembly

Drive Tray

12 150-1129 AC Line Filter

13 340-1792 Left Cover

14 300-1034 520 Watt Power Supply (obsolete)

NS 150-1323 AC On/Off Switch



NS 240-1605 Caster Ball

NS 330-1180 Cable Retainers

NS 340-1676 3U Top Cover

NS 340-1677 6U Filler Panel

NS 340-1784 6U Side Cover

NS 340-1793 Right Cover

NS 340-1800 Half-Height Tape Filler Panel

NS 370-1205 150MB Tape Drive, Half-Height, QIC-150

NS 370-1206 150MB Tape Drive, Full-Height, QIC-150

NS 370-1230 327MB Disk Drive, Imprimis/CDC 77777126

NS 370-1319 669MB Disk, Micropolis 1588-15

NS 370-1319 669MB Disk, Maxtor XT-8760

NS 501-1354 5-Slot VMEbus Backplane, Pressfit

NS 530-1434 External SCSI Cable, 50-Pin SCSI-2, 45 cm (obs)

NS 530-1466 Internal SCSI Cable

NS 530-1826 External SCSI Cable, 50-Pin SCSI-2, 45 cm, Ferrites

NS 540-1800 Caster Plate and Stud

1. Wire harnesses <=530-1465-03 and <=530-1468-02 are not field repairable or replaceable.

These lower revisions are soldered together. Replace both harnesses upon failure. Wire harnesses >=530-1465-04 and >=530-1468-03 are pluggable.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068e.htm (2 von 3) [25.04.2002 16:09:33]


2. Wire harness 530-1469 is not field repairable or replaceable.

3. The 1.3GB SCSI Disk does not fit into Tray 540-1757 or 540-1758.




Sun-4/370/470


Front View

Rear View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (1 von 7) [25.04.2002 16:09:44]



1 501-1439 12-Slot Backplane, Pressfit (obsolete) 1

1 501-1598 12-Slot Backplane, Pressfit

1 501-1832 12-Slot Backplane, Pressfit with DC Harness Cutout


3 340-1877 Side Cover (obsolete)


4 Refer to Codes 18-24

5 330-1192 Front Bezel Blank Insert



NS 340-2249 SCSI Tray Full-Height Bezel

NS 340-1901 SCSI Tray Half-Height Bezel

7 540-1731 Front Bezel Assembly (obsolete)

8 540-1849 Front Bumper (obsolete)

7 & 8

NS

NS

540-1731

240-0558

240-0557

Front Bezel and Bumper Assembly

Miniball Receptacle

Miniball Fastener

9 340-1871 Front EMI Shield, without Switch Assembly

10

NS

NS

NS

540-1748

330-1212

330-1213

340-1936

Switch Assembly (obsolete)

Plastic Remote Switch (obsolete)

Plastic Remote Switch Block (obsolete)

Remote Switch Housing (obsolete)

10

NS

NS

540-2136

330-1373

340-2491

Switch Assembly

Switch

Switch Mounting Bracket http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (2 von 7) [25.04.2002 16:09:44]


11

NS

NS

NS

NS

NS

540-1751

530-1482

540-1732

530-1640

370-1732

370-1214

Fan Tray Assembly, 9 Fans 2

Fan Tray DC Harness for Fan 540-1732




DC Fan Assembly with connector, 150 CFM

12 240-8503 Caster (obsolete)

1. The Sun 4400 CPU is not supported in the 501-1439 Backplane.

2. The Fans are removable from 540-1751-04 and 540-1751-05 to allow access to the fan tray screen during routine preventive maintenance. The fans are not removable from 540-1751-02 or

540-1751-03.

Peripheral Tray

Dual Disk Drives

Disk Drive and Tape Drive http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (3 von 7) [25.04.2002 16:09:44]


12-Slot VMEbus Logic Enclosure - Continued


NS 260-3719 Sun-4/370 Logo

NS 340-1878 Rear Bezel (obsolete)



13 530-1480 Backplane to Interface PCB DC Harness

14

NS

501-1493

140-1019

Interface PCB (SCSI Bus and DC Power)

15 Amp Fuse

15 530-1494 SCSI Bus Internal Command Cable, 25.4 cm

16 340-1892 SCSI PCB Cover



18 340-1903 Peripheral Tray Base

19 501-1496 Peripheral Tray Interface PCB

20 530-1498 Internal SCSI Bus Cable, 1.2M (obsolete) 1

20 530-1729 Internal SCSI Bus Cable, 1.2M 1

21 370-1230 327MB Disk Drive, Imprimis/CDC 77777126

21 370-1319 669MB Disk Drive, Micropolis 1588-15

21 370-1319 669MB Disk Drive, Maxtor XT-8760S http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (4 von 7) [25.04.2002 16:09:44]


22 530-1500 Internal SCSI Bus Cable, 1.2M 2

23 370-1206 150MB Tape Drive, Full-Height, QIC-150

23 370-1247 45/60MB Tape with MT02, Full-Height, QIC-11/24

23 370-1297 2.3GB 8 mm Tape Drive, Full-Height

23 370-1205 150MB Tape Drive, Half-Height, QIC-150

23 370-1347 644MB CD-ROM, Half-Height

24 530-1499 Peripheral Tray DC Harness

NS 530-1638 DC "Y" Harness, Half-Height Peripherals

NS 530-1249 External SCSI Cable, DD-50SA to DD-50SA, 1.0M

NS 530-1593 Ext Cable, 50-Pin SCSI-2 to DD-50SA, 1.0M (obs)


800-3255 12-Slot Office Pedestal Field Service Manual

1. Tape only and Disk with Tape trays use Internal Cable 530-1498 or 530-1729.

2. Disk only, Dual Disk, and Empty trays use Internal Cable 530-1500.

Sun-4/470

12-Slot VMEbus Logic Enclosure http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (5 von 7) [25.04.2002 16:09:44]



1 501-1832 12-Slot Backplane, Pressfit with DC Harness Cutout




5 330-1192 Blank Bezel Insert



7

NS

NS

540-1939

240-0558

240-0557

Front Bezel Assembly

Miniball Receptacle

Miniball Fastener

8 340-2291 Front EMI Cover, without Switch Assembly

NS 340-2292 Blank EMI Cover Filler Panel

NS 340-2444 Peripheral Mounting Bracket

9

NS

NS

540-2136

330-1373

340-2491

Switch Assembly

Switch

Switch Mounting Bracket http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd0068f.htm (6 von 7) [25.04.2002 16:09:44]


10

NS

NS

NS

540-1751

370-1214

530-1640

370-1732

Fan Tray Assembly, 9 Fans 1

DC Fan Assembly with Connector, 150 CFM



11 340-2129 Caster

12 340-2293 Rear EMI Cover


NS 260-3615 SPARCstation 470 Logo


NS 530-1676 Internal SCSI Bus Cable

NS 370-1319 669MB Disk Drive, Micropolis 1588-15

NS 370-1319 669MB Disk Drive, Maxtor XT-8760S



NS 370-1297 2.3GB 8 mm Tape Drive, Full-Height

NS 370-1347 644MB CD-ROM, Half-Height

NS 370-1377 1.3GB Disk Drive, Seagate 976002-012/ST41600N

NS 530-1675 Peripheral Tray DC Harness

NS 530-1842 Grounding Cable, CD-ROM, 12.7 cm

NS 530-1829 SCSI Cable, 50-Pin SCSI-2 to DD-50SA, 1.0M



800-3255 12-Slot Office Pedestal Field Service Manual

1. The Fans are removable from 540-1751-04 and 540-1751-05 to allow access to the fan tray screen during routine preventive maintenance.




Sun-4/390/490

SCSI Peripheral Trays

CODE PART # DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (1 von 6) [25.04.2002 16:09:54]


3

4

1

2

5

6

540-1865

340-2000

530-1474

240-1202

530-1507

340-1832

340-1999

SCSI Tray, Versions 1 and 2 (Shipped before 4/90)

SCSI Tray

SCSI Bus Cable, 73 cm, Internal

#6-32 x 5/8" Peripheral Mounting Screw

SCSI Power Cable, Internal

SCSI Tray Top Cover

Peripheral Cover Plate

10

11

11

12

7

8

9

NS

13

14

15

16

540-1865

340-2143

530-1642

530-1641

530-1638

340-2145

340-2146

340-2305

240-1372

340-2148

240-0258

340-2144

240-0646

SCSI Tray, Version 3 (Shipped after 4/90)

SCSI Tray

SCSI Bus Cable, 180 cm

SCSI Power Cable, Internal

DC Power "Y" Cable, 15 cm

Front Plate

Full-Height Peripheral Blank Plate

Half-Height Peripheral Blank Plate

M4 0.7 x 10 mm Screw

Peripheral Mounting Bracket

#6-32 x 3/8" Peripheral Mounting Screw

SCSI Tray Top Cover

Cable Clamp



NS 370-1297 2.3GB 8 mm Tape Drive, Full-Height

NS 370-1347 644MB CD-ROM, Half-Height

NS 530-1381 External Terminator, 50-Pin DD-50SA



NS 530-1508 Ext Cable, 50-Pin SCSI-2 to SCSI-2, 80 cm (obs)

NS 530-1501 External Cable, 50-Pin SCSI-2 to Centronics, 2.0M

NS 530-1502 External Cable, Centronics to Centronics, 1.5

NS 530-1568 External Cable, 50-Pin SCSI-2 to Centronics, 4.0M




NS 530-1842 Grounding Cable, CD-ROM, 12.7 cm

16-Slot VMEbus Logic Enclosure http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (2 von 6) [25.04.2002 16:09:54]



1 540-1719

540-1840

530-1560

530-1561

150-1393

240-1614

Blower Assembly, 2 Blowers

Centrifugal Fan Assembly

Cable, 32.5 cm, Fan to Terminal

Cable, 86.5 cm, AC Input to Terminal

Capacitor

Terminal Block

2 340-1833 Front RFI Shield

3 240-1372 M4 0.7 x 10 mm Screw http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (3 von 6) [25.04.2002 16:09:54]


4 150-1397 Indicator LED

5 530-1506 Indicator LED Cable


6 300-1047 925 Watt Power Supply (obsolete)

7 501-1498 16-slot Backplane, Pressfit (obsolete)

7 501-1597 16-slot Backplane, Pressfit

NS 540-1869 Load Resistor Assembly (obsolete) 1

NS 180-1189 Power Cord (230V)

NS 180-1190 Power Cord (240V)

NS 230-0203 Cable Tie, 4"

NS 240-0146 Cable Clamp



NS 530-1534 SCSI Power Cable

800-3265 Sun 16-Slot Logic Enclosure Field Service Manual

800-3259 56-Inch Data Center Cabinet Service Manual

1. The Load Resistor Assembly is only required with the 925 Watt Power Supply.

56-inch Data Center Cabinet http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (4 von 6) [25.04.2002 16:09:54]



1 340-1884 Anti-Tilt Panel

2 540-1857 Vented Panel Assembly

3 540-1858 Upper Panel Assembly, 1/2" and 1/4" Tape, Hinged

4 240-1630 #6-32 Ballstud

5 340-1840 Top Panel

6 340-1885 Side Restraint Bracket, Upper

7 240-1372 M4 0.7 x 10 mm Sem Screw http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00690.htm (5 von 6) [25.04.2002 16:09:54]


8 540-1718 Frame Assembly

9 540-2393 Keyswitch Assembly (replaced 540-1285)

10 340-1881 Hinge Bracket

11 340-1848 Side Panel

12 340-1886 Side Restraint Bracket, Lower

13 240-1717 Caster (replaced 370-1210)

14 240-1373 M4 0.7 Kepnut

15 230-1418 Leveler Foot (replaced 230-1181)

16 370-1155 230V Power Sequencer (obsolete)

16 370-1156 240V Power Sequencer (obsolete)

16 300-1263 230V Power Sequencer

16 300-1264 240V Power Sequencer

17 240-1655 #10-32 x 3/4" Screw

18 340-1845 Rear Panel

19 340-2047 Kick Panel

NS 230-1166 Cable Tie 5.5", Reusable

NS 230-1170 Cable Tie 10", Reusable

NS 230-1177 Snap In Clip

NS 240-1738 3/8 x 16 x 4.0 Bolt

NS 240-1739 3/8" x 16 x 7.0 Bolt

NS 240-1748 3/8" x 16 x 4.0 Bolt

NS 340-1835 16-slot Chassis Support Rail, Left

NS 340-1913 Filler Panel, 5.2" x 19"

NS 340-2057 16-slot Chassis Support Rail, Right

NS 340-2138 Ballast, 30 lbs

NS 530-1303 Remote Keyswitch Cable

NS 800-3259 56-inch Data Center Cabinet Service Manual



Sun4/II: PARTS BREAKDOWN - Introduction

Parts Breakdown

This section contains illustrations, part numbers, and descriptions of Sun Systems, Options, Boards,

Input Devices, Monitors, and Printers.

Options such as processor modules, SIMMs, and SBus cards are not included in Volume II. Internal system peripheral options are not included in the Disk, Removable Media, or Miscellaneous chapters.

Parts listed as (obsolete) or (obs) are no longer used to build new systems. Obsolete parts may be replaced with newer part numbers and may not be available.

This manual provides a list of part numbers used to assemble the system or option. Many of the part numbers listed are not normally available as spare parts or as field replaceable service spares, also referred to as Field Replaceable Units, or FRUs.

Spare parts available for purchase are listed in the SunSpares Price List. A list of valid FRU part numbers and part substitutions is available to Sun service and support personnel from SunService logistics.

Standard Configurations and Standard Options supported by Sun Microsystems are documented in the

End User Price List, Reseller Price List, Hardware Configuration Guides, Product Brochures, and

Hardware Installation Manuals.

Abbreviations

Abbreviations used in this section are described below.

Assy Assembly

NS Not shown

Obs Obsolete

Dis Disqualified w With w/o Without

Indicates the part is used in an assembly

FRU Field Replaceable Unit

Class Codes

The first three digits of a Sun part number are the class code. Representative class codes are listed below.

CLASS CODE DESCRIPTION

270-xxxx-xx PCB Fabrication

300-xxxx-xx Power Supply

330-xxxx-xx Plastic Part

340-xxxx-xx Sheet Metal Part

365-xxxx-xx Monitor Assembly http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c5.htm (1 von 6) [25.04.2002 16:10:05]


370-xxxx-xx OEM Part

500-xxxx-xx Untested PCB

501-xxxx-xx Tested PCB

520-xxxx-xx Programmed IC

525-xxxx-xx Programmed IC

530-xxxx-xx Cable

540-xxxx-xx Assembly

555-xxxx-xx FRU Assembly

560-xxxx-xx Shipping Kit

570-xxxx-xx Electro Mechanical Assembly

595-xxxx-xx Top Level Option Assembly

596-xxxx-xx Configured Option Assembly

600-xxxx-xx Top Level System Assembly

700-xxxx-xx Software Tape

704-xxxx-xx Software CD-ROM

790-xxxx-xx Software Tape and Manual

794-xxxx-xx Software CD-ROM and Manual

800-xxxx-xx Sun Manual



804-xxxx-xx CD-ROM Insert

807-xxxx-xx FCO Kit

813-xxxx-xx Configuration Manual

825-xxxx-xx Manual Set

855-xxxx-xx Manual Set

950-xxxx-xx Engineering Specification

Part Numbers

Sun part numbers consist of nine numerical digits separated with dashes (-) into three components;

Class Code, Base Number, and Dash Number. A revision number or letter is used with each part number.

Class Codes identify similar parts.

Base Numbers are assigned sequentially. A higher base number does not necessarily indicate a new or improved part.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c5.htm (2 von 6) [25.04.2002 16:10:05]


Higher/Lower Base Number Examples

PART #

300-1281

300-1286

DESCRIPTION

SC2000 Power Supply

SC2000 Power Supply

501-2925

501-2940

501-3001

SM71 SuperSPARC 2.4.5

SM71 SuperSPARC 2.3

SM71 SuperSPARC 2.4.3

501-2324

501-2924

501-2961

SS20 CPU

SS20 CPU

SS20 CPU*

RELEASE DATE

3/28/95

9/19/94

9/28/95

6/05/95

8/14/95

1/10/94

9/14/95

7/12/95

* 501-2961 is a screened and re-labeled 501-2324.

Dash Numbers are used to identify changes made to the part that affect form, fit, or function.

Revision Numbers are used to identify changes made to the part that do not affect form, fit, or function.

System Serial Number

The system serial number contains four fields of information:

Year - year of manufacturer

Week - week of manufacturer

Plant - manufacturing location

Serial number - numeric or alphanumeric serial number

Example:

Plant Code

CODE LOCATION

C Mountain View Building 4, California

F Milpitas Building 4, California

G Westford, Massachusetts

H Singapore (Sun-3 Shoebox)

K Milpitas Building 5, California

L Milpitas Building 7, California (Specials Engineering)

M Linlithgow, Scotland

N Japan

P Billerica, Massachusetts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c5.htm (3 von 6) [25.04.2002 16:10:05]


R Japan (used by Fuji Xerox)

T Milpitas, California (Re-Manufacturing)

Tools


250-1028 Field Engineer Toolkit (Jensen JTK-679-1)

250-1024 T9 Torx Screwdriver

250-1025 T7 Torx Screwdriver

250-1026 T25 Torx Blade

250-1017 #2 Pozidrive Blade

250-1029 3/32" Hexdriver Blade

250-1030 7/64" Hexdriver Blade

250-1031 14 mm Deep Socket


250-1033 Blue Cordora Zipper Case

250-1034 3 1/8" Driver Handle

250-1035 4 1/8" Driver Handle

250-1036 1/4" Drive Spinner Handle

250-1037 5" Extension Blade

250-1038 #1 Phillips Blade

250-1039 #2 Phillips Blade

250-1040 1/4" Slotted Blade

250-1041 3/16" Slotted Blade

250-1042 Alignment Tool

250-1043 Alignment Tool

250-1044 4 1/2" Miniature Diagonal Cutter

250-1045 5.25" Diagonal Cutting Pliers

250-1046 6.5" Thin Needlenose Pliers

250-1047 4" Adjustable Wrench

250-1048 6" Adjustable Wrench

250-1049 Crimping Tool/Wire Stripper

250-1050 Fluke 75 Digital Multimeter

250-1051 1.27 mm Hexdriver Blade


250-1053 2 mm Hexdriver Blade





250-1058 4 mm Nutdriver Blade http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c5.htm (4 von 6) [25.04.2002 16:10:05]


250-1059 4.5 mm Nutdriver Blade

250-1060 5 mm Nutdriver Blade

250-1061 5.5 mm Nutdriver Blade








Power Screwdriver Kit


250-1075 Cordless Power Screwdriver Kit (Jensen JTK-864)

250-1076 Two Speed Power Screwdriver

250-1077 Screwdriver Carrying Case

250-1078 Screwdriver Battery Charger, 115V

250-1079 Screwdriver Battery

250-1084 Power Screwdriver Xcelite Adapter

Vacuum Cleaner Kit


250-1080 Vacuum Cleaner Kit (Jensen JTK-863)

250-1081 Vacuum Cleaner, 115V

250-1082 Vacuum Cleaner Filters (qty 6)

250-1083 Vacuum Cleaner Carrying Bag

Miscellaneous Tools


240-1433 2 mm Hex Key

240-1716 AMP SIMM Extraction Tool (obsolete)

240-1718 EPROM Insertion Tool

240-1719 IC Extraction Tool

240-1822 Modified AMP SIMM Extraction Tool (obs)

240-1904 1/2" Open-End Wrench

250-1007 Disposable ESD Wrist Strap

250-1011 Slotted & 2 mm Hex Screwdriver http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c5.htm (5 von 6) [25.04.2002 16:10:05]


250-1072 1/2" x 1/2" Thin-Head Wrench for 56" Rack Levelers

250-1074 10-Inch End Cutter

250-1088 Sun ESD Mat with Sun Logo

330-1145 Disposable ESD Mat

330-1646 SS10 and SS20 SIMM Insertion Tool (order 560-1936)

330-1836 SS20 Fan Installation Tool

330-1852 SS Voyager Power Supply Extraction Tool

345-1131 SIMM Extraction Wire Tool (obsolete)

345-1132 SIMM Extraction Wire Tool (obsolete)

None T8 Torx Blade (Xcelite 99-8XTD)

None T10 Torx Blade (Xcelite 99-10XTD)

370-1906 90° L-Key T10 Torx

370-1907 90° L-Key T15 Torx

560-1763 SIMM Extraction Tool Kit

345-1184 Machined SIMM Extraction Tool 345-1184-01 (obsolete)

Diecast SIMM Extraction Tool 345-1184-02



Sun4/I: Slot Assignment - Contents

Slot Assignment

Board Installation Notes

VMEbus Bus Grant and Interrupt Acknowledge

SCSI Host Adapter Assemblies


Sun-4/110

Sun-4/150

Sun-4/260

Sun-4/280

Sun-4/310

Sun-4/330

Sun-4/350

Sun-4/360

Sun-4/370

Sun-4/380

Sun-4/390

Sun-4/470

Sun-4/490


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004c2.htm [25.04.2002 16:10:08]

Sun4/I: Slot Assignment - Board Installation Notes

Board Installation Notes

Backplane Slot Assignment Charts

Each system chart lists the PCB slot assignments in order of descending priority. In the charts

A,B,C... indicates the preferred location for a specific board. An A is the most preferred location. An

a indicates that a board requires more than one slot if Memory, Frame Buffer, or other options are installed. Multiple capital letters (AA, BBB...) indicate a board requires more than one slot. Boards with multiple part numbers are shown with a footnote (Sun 3004 CPU 1) and are listed in tables after each grouping of slot assignment charts.

Installing VMEbus Boards

1. Refer to the Backplane Slot Assignment Charts to determine where to install additional boards.

2. Move boards in the cardcage as required.

3. Configure backplane jumpers for BG3 and IACK. The IACK jumper for the last slot is not present on some backplanes. It is not needed.

Removing VMEbus Boards

1. Refer to the Backplane Slot Assignment Charts to determine if other boards in the cardcage require repositioning.

2. Configure backplane jumpers for BG3 and IACK.

3. Install an air restrictor and the external filler panel in any unused slot.

Sun-3/260 and Sun-4/260

1. Do not install an air restrictor in Slot 2.

2. Do not install non-memory board options in Slots 2 through 5 using the standard left to right sequence. If possible, leave Slot 2 empty for system cooling.

Sun 4100 CPU

1. The Sun 4100 CPU does not have a VMEbus slave interface. VMEbus boards requiring a slave interface on the processor do not function with the Sun 4100 CPU (eg. Xylogics 451, Xylogics

472, Xylogics 7053).

2. The Sun 4100 CPU has 28-bits of physical address space. Bit 27 is replicated out to Bit 31 in

A32D32 space.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f3.htm (1 von 6) [25.04.2002 16:10:17]


Sun 4400 CPU

1. The Sun 4400 CPU requires 12-slot Backplane 501-1598 or 501-1382. The Sun 4400 CPU is not supported in the 501-1439 12-slot Backplane.

2. The Sun 4400 CPU requires 16-slot Backplane 501-1498-02 or 501-1597.

Sun 3200, 3400, and 4200 ECC Memory

1. 501-1092 or 501-1117 BackpIanes. Install the first Memory board in Slot 6. Install 220/270

Terminating Resistor 120-1613-01 at location F-34 or F-54 on the Memory board.

Remove the Terminating Resistor from location F-34 or F-54 on Memory boards installed in

Slots 2, 3, 4, and 5.

2. 501-1439, 501-1598, or 501-1832 Backplanes.

Install the first Memory board in Slot 1. Install 220/270 Terminating Resistor 120-1613-01 at location F-34 or F-54 on the Memory board.

If placement results in Memory boards on both sides of the Sun 3400 CPU, remove the

Terminating Resistor at location O-23 (U1411) on the CPU. Install Terminating Resistors on

Memory boards in Slot 1 and Slot 7.

3. Remove Jumpers P10, P11, P12, and P13 from the 501-1598 Backplane when the Sun 3400 board set is installed.

4. Remove Jumpers P10, P11, P12, and P13 from the 501-1832 Backplane when the Sun 3400 board set is installed.

GP2

The GP2 does not function with the Sun-2 Color board, Sun-3 Color board, or the Graphics Buffer.

CG5 with GP+ or GP

1. The CG5 P2 bus must be disabled (SW3300-5, OFF).

2. The CG5 must be installed in slots that do not share the P2 bus with the GP or GP+. Signals provided by the CG5, but not used by the GP or GP+, may cause contention.

CG5 with GP2

1. The CG5 P2 bus must be enabled (SW3300-5, ON).

2. The CG5 must be installed in cardcage slots that share the P2 bus with the GP2.

CG5 without GP2

The CG5 P2 bus must be disabled (SW3300-5, OFF).



CG9 with GP2

1. The CG9 P2 bus must be enabled (SW3-1, OFF).

2. The CG9 must be installed in cardcage slots that share the P2 bus with the GP2.

3. This configuration is not supported with the TAAC-1.

4. The CG9 is not supported without the GP2.

TAAC-1

1. The TAAC-1 requires three slots. Install backplane jumpers BG3 and IACK in all three slots.

2. The TAAC-1 is not supported with the CG9 and GP2 GXP Graphics Options.

Xylogics 450 Disk Controller

1. Do not mix the Xylogics 450 with the Xylogics 7053.

2. Xylogics 450 is not supported with the 900MB Disk Drive, and cannot be mixed with the

Xylogics 451 in any 900MB Disk Drive configuration.

Xylogics 7053 Disk Controller

1. Do not mix the Xylogics 7053 with the Xylogics 450.

2. Systems with Sun-2 SCSI, 501-1138, or Sun-3 SCSI, 501-1217, may mix a maximum of one

Xylogics 451 and two Xylogics 7053s.

3. Systems with Sun-2 SCSI, 501-1167, may mix a maximum of one 451 and two 7053s.

4. Systems with Sun-2 SCSI, 501-1149, or Sun-3 SCSI, 501-1170, may mix a maximum of one

Xylogics 451 and one Xylogics 7053.

5. The Sun-4/470 and Sun-4/490 may mix a maximum of one Xylogics 7053 and one ISP-80 IPI-2 controller.

ALM-1, ALM-2, and MCP

1. The ALM-2 and MCP share the same base address and interrupt vector.

2. The ALM-1 shares the same interrupt vector as the ALM-2 and MCP.

3. Because of the conflict with the interrupt vector, no more than four ALM-1, ALM-2, or MCP boards can be installed at the same time.

4. The ALM-1, ALM-2, or MCP boards must be installed in sequential address order, or a conflict with the interrupt vector may result.

5. The maximum combination of ALM-2 and MCP boards allowed is eight. When mixing ALM-2 and MCP, the MCP must be addressed as Boards 1, 2, 3, and 4.

6. The maximum number of MCP boards is four.

7. The maximum number of ALM-2 boards is eight.



BOARD

ALM-1

VECTOR

ALM-2 & MCP

VECTOR

7

8

5

6

3

4

1

2

-

-

-

-

0x88

0x89

0x8a

0x8b

0x8b

0x8a

0x89

0x88

0xa0

0xa1

0xa2

0xa3

ALM-1 501-1157 (Pedestal Systems)

The ALM-1 must be installed in Slots 11 and 12. Install Backplane Jumpers BG3 and IACK in Slot

11. Remove Backplane Jumper BG3 from Slot 12.

MAPkit

1. The MAPkit requires two slots. Remove Backplane Jumpers BG3 and IACK from the slot that contains the MAPkit board nearest to Slot 1. Install Backplane Jumpers BG3 and IACK in the second slot.

2. The MAPkit data throughput rate may be affected if a Tape Controller or a Disk Controller is installed in an unused slot between the CPU and the MAPkit.

SunLink Channel Adapter

1. The SCA requires two slots. Remove Backplane Jumpers BG3 and IACK from both slots.

2. Installing a 1/2" Tape Controller or an SMD Controller in an unused slot between the CPU and the SCA option may affect the SCA data throughput rate.

12-Slot Office Pedestal Backplane 501-1382

A cutout in the upper left corner of the 501-1382 Backplane allows the DC Wire Harness to be routed from the rear of the Backplane to the front of the Peripheral Tray.

VME to Multibus Adapter Board

Use Adapter board subassembly 501-1054-04, Rev. A, or greater, to avoid signal contention on the P2 bus. This change was effective in September 1985 (ECO 1850).



SBus Expansion Subsystem Board

The SBus Expansion Subsystem Board does not use the VMEbus.

Systech MTI-800, MTI-850, MTI-1600, and MTI-1650

Tables A and B provide reference information for Systech boards packaged in kits.

Table A identifies the ALM boards in a Sun PCB kit. Columns 2, 3, and 4 provide the Sun PCB part number, a board description, and the Systech part number for individual boards within each set.

Table A

SUN PCB

KIT P/N

SUN PCB

P/N

DESCRIPTION

370-1046 MTI-800: 8-Channel USARTPCB

370-1039

370-1047 MTI-800/1600 Multiplex Controller PCB

370-1048 MTI-1600 : 16-Channel USART PCB

370-1040

370-1047 MTI-800/1600 Multiplex Controller PCB

370-1102 MTI-850B : 8-Channel USART PCB

370-1098

370-1099 MTI-850/1650 Multiple Controller PCB

370-1100 MTI-1650B : 16-Channel USART PCB

370-1097

370-1096

SYSTECH

P/N

65-201616-7

65-200004-7

65-201516-6

65-200004-7

65-201606-6

65-201004-8

65-201506-5

370-1099 MTI-850/1650 Multiple Controller PCB 65-201004-8

811-1100 MTI-1650A : 16-Channel USART Rack-Mount Box 65-701005-4

370-1099 MTI-850/1650 Multiple Controller PCB 65-201004-8

Table B describes the boards in a Sun VME assembly kit. This assembly contains an ALM board set, a VME-Multibus Adapter PCB, and frame. Column 1 lists the Sun VME assembly part number.

Columns 2 and 3 provide the part numbers and a description of the ALM channel and the

VME-Multibus Adapter PCB in the Sun VME assembly kit. Only three of the PCB kits from Chart A are used as VME options. Systech discontinued the 800/1600 series when the 850-1650 series was introduced. Replace the entire VME assembly upon failure of any component in these VME options.

Table B

SUN VME

KIT P/N

SUN PCB

KIT P/N

DESCRIPTION

501-1157-01

370-1040 MTI-1600 : 16-Channel ALM for VME systems (replaced by 370-1097)

501-1054 VME-Multibus Adapter PCB

501-1157-02

370-1097 MTI-1650B : 16-Channel ALM for Desk-side systems


370-1096 MTI-1650A Controller

501-1165


Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f3.htm (5 von 6) [25.04.2002 16:10:17]


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f3.htm (6 von 6) [25.04.2002 16:10:17]

Sun4/I: Slot Assignment - VMEbus Bus Grant and Interrupt Acknowledge

VMEbus Bus Grant and Interrupt

Acknowledge

This chart shows how the Bus Grant In/Out and Interrupt Acknowledge In/Out signals are connected on the board. Wired signals are not used. Open signals are selected with backplane jumpers. Option signals are enabled on the board and on the backplane.

DESCRIPTION BG0 BG1 BG2 BG3 IACK

4100 CPU Wired Wired Wired Open Wired

4200 CPU

4300 CPU

Wired Wired Wired Open


Wired

Open

4400 CPU

600MP CPU

CG2 Color

CG3 Color



Wired

Open

Wired Wired Wired Wired Open


CG5 Color

CG9 Color

GB

GP & GP+

GP2

TAAC-1

VX

MVX



Wired Wired Wired Wired Wired



Open



Open Open Open Open Open

Open

3/E Mono

3/E Color



VME-Multibus Wired Wired Wired Open Open

Xylogics 7053 Option Option Option Option Open

ISP-80 IPI-2

Prestoserve

ALM-2

MCP

Open Open Open Open Open




HSI Wired Wired Wired Wired Open

Channel Adapter Option Option Option Option

FDDI

SCSI-2

Wired Open Open Open Open

Option Option Option Option Open

SCSI-3

3/E SCSI

IPC



Open Open Open Open

Open

Open

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f4.htm (1 von 2) [25.04.2002 16:10:20]

Sun4/I: Slot Assignment - VMEbus Bus Grant and Interrupt Acknowledge


Sun4/I: Slot Assignment - SCSI Host Adapter Assemblies

SCSI Host Adapter Assemblies

1. Use the slot assignment charts for systems with the 501-1138 or 501-1217 SCSI Assembly if there is no SCSI Host Adapter installed in a Sun-3/180, Sun-3/280, or Sun-4/280.

2. Sun 3x2 Adapter, 501-1269, Option 160A, is connected to J2 Rows A and C. There is no external connector.

3. Sun 3x2 Adapter, 501-1191, Option 160B, is not connected to J2 Rows A and C. There is no external connector.

4. Sun 3x2 Adapter, 501-1220, has no connection to J2 Rows A and C and has an external 50-pin connector.

5. Sun 3x2 Adapter, 501-1666, is connected to J2 Rows A and C and has an external 50-pin connector. This adapter connects the Sun 4300 CPU to the internal SCSI subsystem of the

Sun-4/360.

6. Sun-2 SCSI Host Adapter, 501-1167, has P2 bus connections and an external cable assembly.

Do not substitute a 501-1236 Sun-3 SCSI for a 501-1045 Sun-2 SCSI in this adapter assembly.

7. Sun-3 SCSI Host Adapter, 501-1217, does not function with the SCSI subsystem in the

Sun-3/160, Sun-3/260, or Sun-4/260. The SCSI subsystem interfaces through J2, Rows A and

B, of the VMEbus connector. These signals are not connected on the 501-1217 assembly.

Sun VME 3x2 SCSI Host Adapter Assemblies

ASSY # w SCSI

INCLUDES

SCSI #

501-1138 501-1045

INCLUDES

BLANK ASSY #

500-1220

P2 ROWS

A + C

SCSI

CONNECTION

No External

501-1149 501-1045

501-1167 501-1045

501-1170 501-1236

501-1217 501-1236

500-1269

500-1059

500-1269

500-1220

Yes

Yes

Yes

No

Internal

External

Internal

External

Sun 3x2 Adapter Assemblies

OPTION #

TESTED

ASSY #

ADAPTER

FAB #

P2 ROWS

A + C

EXTERNAL

CONNECTION

160A 501-1269 270-1059

160B 501-1191 270-1138

Yes

No

No

No

None 501-1220 270-1138

None 501-1666 270-1059

No

Yes

Yes

Yes http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005f5.htm (1 von 2) [25.04.2002 16:10:24]

Sun4/I: Slot Assignment - SCSI Host Adapter Assemblies

Memory Boards With SCSI

ASSY # MEMORY BD # DESCRIPTION SCSI HOST

501-1147 501-1079 2/50 0MB 501-1045

501-1172 501-1121 3/75 0MB 501-1045

Memory Boards That Can Use A 501-1045 SCSI

MEMORY BD # DESCRIPTION

501-1020 2/50 1MB

501-1046

501-1047

2/50 2MB

2/50 4MB

501-1067

501-1079

501-1111

501-1121

501-1122

2/50 3MB

2/50 0MB

3/75 2MB

3/75 0MB

3/75 4MB



Sun4/I: Slot Assignments - Sun-4/110

Sun-4/110

SHUNTS

BG3 IACK

BOARD

SLOT POSITION

1

Out Out Sun 4100 CPU

(1)

A

2

A

3

In Out MCP

In Out ALM-2

In Out Color

(2)

A

A

A

In Out HSI

Out Out Ethernet

Out Out FDDI

In Out IPC

(3)

A

A

A

A

References

1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2004-16.

2. Cardcage Slot Assignments and Backplane Configuration Procedures for the Sun 4/110,

813-2053-05.



Sun4/I: Slot Assignments - Footnotes for Sun-4/110/150/260/280

Footnotes to Slot Assignments for

Sun-4/110/150/260/280

NOTE # PART # BOARD

1 501-1199

501-1237

501-1462

501-1463

501-1464

501-1465

Sun 4100 CPU (-03 FAB) 8MB w/o FPU

Sun 4100 CPU (-03 FAB) 8MB w FPU





501-1512

501-1513

501-1514

501-1515

501-1516

501-1517







501-1656

501-1657

501-1658

501-1659

501-1660

501-1661







501-1247

501-1248

501-1371

501-1374

501-1518

501-1532

MG3 P4 Mono Frame Buffer

CG4 P4 Color Frame Buffer

CG8 P4 24-Bit Color Frame Buffer


CG8 P4 24-Bit Color Frame Buffer


501-1314

501-1466

256KB SIMM Module

1MB SIMM Module


2 501-1116

501-1267

Sun-3 Color Frame Buffer

CG5 Color Frame Buffer

The Sun-2 Color Board is not supported.


3 501-1125

501-1214

SunIPC without 80287

SunIPC with 80287


4 501-1055

501-1139

501-1268

Graphics Processor

Graphics Processor +

Graphics Processor 2 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00605.htm (1 von 2) [25.04.2002 16:10:32]

Sun4/I: Slot Assignments - Footnotes for Sun-4/110/150/260/280


5 501-1383

501-1447

TAAC-1 Application Accelerator


NOTE # PART #

6 501-1102

501-1451

501-1254

501-1576

8MB Memory

32MB Memory

32MB Memory

16MB Memory

BOARD


7 501-1149

501-1170

Sun-2 SCSI Host Adapter Assembly



8 501-1155 Xylogics 472 Tape Controller Assy

The 501-1156, CPC Tapemaster

Tape Ctlr Assembly is not supported.


9 501-1154

501-1166

501-1249

Xylogics 450 Disk Controller Assembly


Xylogics 7053 Disk Controller


10 501-1249 Xylogics 7053 Disk Controller


11 501-1167 Sun-2 SCSI Host Adapter Assembly


12 501-1138

501-1217






Sun-4/150

SHUNTS

BG 3 IACK

BOARD

1

SLOT POSITION

2

Out Out

Sun 4100 CPU (1)

A A

3 4 5 6

Out Out

GP (4)

A

In In GB

In

In

In

In

In

In

TAAC-1

(5)

In Out 1st MCP

In Out 2nd MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out

Color (2)

In Out CG5 with GP/GP+

In Out CG5 with GP2

In Out CG9 Color

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out FDDI

In Out 1st IPC

(3)

In Out 2nd IPC

(3)

A B

A B

A B

A B C D E

A B C D

A B C D E

A B C D

A B C D

A B

A

A

A

A

B

A

B

B

B

A

A

C

C

C

B

A

A

C

References

1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2004-16.

2. Cardcage Slot Assignments and Backplane Configuration Procedures for the Sun 4/150

Systems, 813-2054-01.




Sun-4/260

SHUNTS

BG 3 IACK

BOARD

Out Out Sun 4200 CPU A

In In

1st Memory (6)

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

A

In In

2nd Memory (6)

In In 3rd Memory

(6)

A

A

In In 4th Memory

(6)

Out Out

GP (4)

In In GB

In

In

In

In

In

In

TAAC-1

(5)

Out Out ALM-1

Out Out SCSI

(7)

Out

Out

Out

Out

Out

In

Out

In

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

In

Out

In

1st Channel

Adapter

2nd Channel

Adapter

1st MAPkit

2nd MAPkit

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out 1st IPC

(3)

In Out 2nd IPC

(3)

In Out

3rd IPC (3)

A

A

A

E F

E F

E F

D C

D

B

C

D

A

B

C

A

B A

A A

A

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H

A C D E F G

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H

A B C D E F G

H A A C C D D

E

F

E

A A B B

C

D

C

F

G

D

E

H

G

F

E

F

A B

A

C

B C

A

A

D E

D

F

E

B C

B

D

C

G

F

E

D

H

G H

F

E F

D A B C E F G H I J

C A B D E F G H I

D A B C E F G H I J

D A B C E F G H I J

C A B D E F G H I

A B C D E F G H I J

A B C

A B

D E F G H I

C D E F G H http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fa.htm (1 von 3) [25.04.2002 16:10:53]


In Out 4th IPC

(3)

Out Out 1st Tape Ctlr

(8)

Out Out 2nd Tape Ctlr

(8)

Out Out 1st Disk Ctlr

(9)

A B C D E F G

A B C D E F

A B C D E

A B C D E F

Out Out 2nd Disk Ctlr

(9)

In Out

Color (2)

A B C D E

J A B C D E F G H I

In Out CG5 w GP/GP+ G A B C D E F

In Out CG5 w GP2

In Out CG9 Color

A B

A B

References

1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2004-16.

2. Sun-4/200 Cardcage Slot Assignments and Backplane Configuration Procedures, 813-2037-05.

Sun-4/260 with Double-Height Backpane

SHUNTS SLOT POSITION

BOARD

BG 3 IACK 1 2 3 4 5 6 7 8 9 10 11 12

Out Out Sun 4200 CPU A A

In In

1st Memory (6)

A

In In

2nd Memory (6)

In In 3rd Memory

(6)

A

A

In In 4th Memory

(6)

Out Out

GP (4)

In In GB

In

In

In

In

In

In

TAAC-1

Out Out ALM-1

(5)

Out Out SCSI

(7)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

A

E

E

E

D C

D

B

C

D

A

A

B

C

A

A

B A

A A

A

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E F G H I http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fa.htm (2 von 3) [25.04.2002 16:10:53]


In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

In

Out

In

Out

Out

Out

Out

Out

In

Out

In

1st Channel

Adapter

2nd Channel

Adapter

1st MAPkit

2nd MAPkit

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out 1st IPC

(3)

In Out 2nd IPC

(3)

In Out

3rd IPC (3)

In Out 4th IPC

(3)


(8)


(8)

Out Out 1st Disk Ctlr

(9)

Out Out 2nd Disk Ctlr

(9)

In Out

Color (2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

A B C D E F G H

A B C D E F G

A B C D E F

A B

A B

C D

C

A B

A

E

D

C

B

F

E

D

C

G

F G

E

D E

A B

A B

C D

C

E

D

A B

A

C

B

F

E

D

C

G

F G

E

D E

A B C D E F G H I

A B C D E F G H

A B C D E F G H I

A B C D E F G H I

A B C D E F G H

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E F

A B C D E

A B C D E F

A B C D E

A B C D E F G H I

A B C D E F

A B

A B

References

1. Sun Systems Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2004-16.

2. Cardcage Slot Assignments and Backplane Configuration Procedures for Sun 4/200 Systems

with Double-Height Backpanels, 813-2071-05.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fa.htm (3 von 3) [25.04.2002 16:10:53]

Sun4/I: Slot Assignment - Sun-4/280

Sun-4/280 with 501-1167 SCSI Host Adapter

SHUNTS

BG3 IACK

BOARD


In In

1st Memory (6)

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(4)

In In GB

In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

Out Out

SCSI (11)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

In

Out

In

Out

Out

Out

Out

Out

In

Out

In

1st Channel

Adapter

2nd Channel

Adapter

1st MAPkit

2nd MAPkit

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

E F

A

E F

E F

A B C D

A B C

A B

A

A B C D

A B C

A B

A

A B

A

C

B C

A

A

A B

A

C

B C

A

A

A B C D

A B C D

D C

A

D

B

C

D

A

A

B

C

A

A

A

B A

A

A

D

C D

B C D E F

E F G H I

D E F G H

C D E F G

B C D E F

D E

D

B C

B

D E

D

B C

B

F

E

D

C

F

E

D

C

G

F G

E

D E

G

F G

E

D E

E F G H I

E F

A B

A B http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (1 von 10) [25.04.2002 16:11:27]


In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (3)

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

In Out 4th IPC

(3)


(8)


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)

Out Out 3rd Disk Ctlr

(10)

Out Out 4th Disk Ctlr

(10)

A B C D

A B C

A B C D

A B C D

A B C

A B C D

A B C

A B

A

E F G H I

D E F G H

E F G H I

E F G H I

D E F G H

E F G H I

D E F G H

C D E F G

B C D E F

A B C D E

A B C D

A B C D E

A B C D

A B C

A B

References


813-2004-16.


Sun-4/280 with Double-Height Backpanel with 501-1167 SCSI Host Adapter

SHUNTS

BG3 IACK

BOARD

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12


In In

1st Memory (6)

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(4)

In In GB

A

A

A http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (2 von 10) [25.04.2002 16:11:27]


In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

Out Out

SCSI (11)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

In

Out

In

Out

Out

Out

Out

Out

In

Out

In

1st Channel

Adapter

2nd Channel

Adapter

1st MAPkit

2nd MAPkit

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (3)

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

In Out 4th IPC

(3)


(8)


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)


(10)

E

E

E

D C

D

B

C

D

A

B

C

A

B A

A

A

A

A

A B C D

A B C

A B

A

A B C D

A B C

A B

A

A B

A

C

B C

A

A

A B

A

C

B C

A

A

D

C D

B C D E F

E F G H I

D E F G H

C D E F G

B C D E F

D E

D

B C

B

D E

D

B C

B

F

E

D

C

F

E

D

C

G

F G

E

D E

G

F G

E

D E

A B C D E F G H I

A B C D E F

A B C

A B

A B

A B

D E F G H

C D E F G

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E F

A B C D E

A B C D E F

A B C D E

A B C D http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (3 von 10) [25.04.2002 16:11:27]



(10)

A B C

References

1. Sun Systems ardcage Slot Assignments and Backplane Configuration Procedures, 813-2004-16.



Sun-4/280 with 501-1138 or 501-1217 SCSI


BOARD

BG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12


In In

1st Memory (6)

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(4)

In In GB

In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

Out

Out

Out

1st Channel

Adapter

2nd Channel

Adapter

A

A

A

E F

E F

E F

D C

D

B

C

D

A

B

C

A

B A

A

A

A

A B C D

A B C D

A B C D

A B C D

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B

A

C

B C

A

A

C D

C

B C

B

E

D

D

C

F

E

E

D

G

F G

F

E F http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (4 von 10) [25.04.2002 16:11:27]


Out

In

Out

In

1st MAPkit

Out

In

Out

In

2nd MAPkit

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out

SCSI (12)

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (3)

A B

A

C

B C

A B C D

D E

D

F

E

G

F

H

G H

A

A

B C

B

D

C

E

D

F

E F

D A B C E F G H I J

C A B D E F G H I

D A B C E F G H I J

E F G H I J

A B C D E F G H I J

A B C D E F G

A B

A B

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H I J

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H I J

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

A B C D E F G H I

A B C D E F G H

In Out 4th IPC

(3)

A B C D E F G


(8)

A B C D E F G H I J


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)


(10)


(10)

A B C

A B C D

A B C

A B

A

D E F G H I

E F G H I

D E F G H I

J

C D E F G H

B C D E F G

References


813-2004-16.


http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (5 von 10) [25.04.2002 16:11:27]


Sun-4/280 with Double-Height Backpanel with 501-1138 or 501-1217 SCSI


BOARD

BG3 IACK 1 2 3 4 5 6 7 8 9 10 11 12


In In

1st Memory (6)

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(4)

In In GB

In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

Out

Out

Out

1st Channel

Adapter

2nd Channel

Adapter

Out

In

Out

In

Out

In

Out

In

1st MAPkit

2nd MAPkit

Out Out

SCSI (12)

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

A

A B C

A B C

A

A

E

E

E

D C

D

B

C

D

A

B

C

A

B A

A

A

A

A B C D

A B C D

A B C D

A B C D E F

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

A A

B B

C D

C

A B

A

E

D

C

B

F

E

D

C

G

F G

E

D E

A B

A B

C D

C

A B

A

E

D

C

B

F

E

D

C

G

F G

E

D E

A B C D E F G H I

D E F G H I

D E F



In Out CG9 Color

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (3)

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

In Out 4th IPC

(3)


(8)


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)


(10)


(10)

A B

A B C D E F G H I

A B C D E F G H

A B C D E F G H I

A B C D E F G H I

A B C D E F G H

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E F G H I

A B C D E F G H

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

References


813-2004-16.



Sun-4/280 with 501-1138 or 501-1217 SCSI

Slots 7,8,9 reserved for non-Sun boards that use P2

SHUNTS

BG3 IACK

BOARD


In In

1st Memory (6)

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(4)

In In GB

A

A

A http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (7 von 10) [25.04.2002 16:11:27]


In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

1st Channel

Adapter

Out

Out

Out

Out

Out

Out

Out

Out

2nd Channel

Adapter

1st MAPkit

Out

Out

Out

Out

2nd MAPkit

Out In

SCSI (12)

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

In

In

Out

Out

Out

In

Out

Out

Out

Out

Out

Out

1st HSI

2nd HSI

Ethernet

1st FDDI

2nd FDDI

1st IPC (3)

B C

B C

B C

A B C D

A B C D

A B C D

A B C

A B C D

A B C D

A B C

A B C D

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

A B C

A

In Out 4th IPC

(3)

A


(8)

A B C D

A B C D

A B C

A B

A

A B C D

A B C

A B

A

A B

A

C

B C

A

A

A B

A

C

B C

A

A

A B C D


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)


(10)

A B C

A B C D

A B C


A

A

A

A

A

A

D E F

C D E

B C D

E F G

D E F

C D E

B C D

D E

D E

B C

B C

D E

D E

B C

B C

E F G

E F G

A B

A B

E F G

D E F

E F G

E F G

D E F

E F G

D E F

C D E

B C D

E F G

D E F

E F G

D E F

C D E



(10)

A B C D

References


813-2004-16.


Sun-4/280 with Double-Height Backpanel with 501-1138 or 501-1217 SCSI

Slots 7,8,9 reserved for non-Sun boards that use P2

SHUNTS

BG3 IACK

BOARD

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12


In In

1st Memory (6)

A

In In 2nd Memory

(6)

In In

3rd Memory (6)

A

A

In In

4th Memory (6)

Out Out GP

(2)

In In GB

In

In

In

In

In

In

TAAC-1

(5)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

B

B

B

A

A B C

A B

A

A B C

A B

A

A

A

A

A

A

A

D E F

A

A

C D E

B C D

A B C

D E F

C D E

B C D

A B C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (9 von 10) [25.04.2002 16:11:27]


Out

Out

Out

Out

Out

In

Out

Out

Out

Out

Out

In

1st Channel

Adapter

2nd Channel

Adapter

1st MAPkit

Out

In

Out

In

2nd MAPkit

Out Out

SCSI (12)

In Out Color

(2)

In Out CG5 w GP/GP+

In Out CG5 w GP2

In Out CG9 Color

In Out 1st HSI

In Out 2nd HSI

Out Out Ethernet

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (3)

In Out

2nd IPC (3)

In Out 3rd IPC

(3)

In Out 4th IPC

(3)


(8)


(8)

Out Out

1st Disk Ctlr (9)

Out Out

2nd Disk Ctlr (9)


(10)


(10)

A B

A

C

B C

A

A

A B

A B

A B C

A B C

A B C

A B C

A B

A B C

A B

A

A B C

A B

A B C

A B C

A B

A B C

A B

A

D E

D E

B C

B C

C D

C D

A B

A B

D E F

D E F

A B

A B

D E F

C D E

D E F

D E F

C D E

D E F

C D E

B C D

A B C

D E F

C D E

D E F

C D E

B C D

A B C

References


813-2004-16.




Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fb.htm (10 von 10) [25.04.2002 16:11:27]


Sun-4/310

SHUNTS

BG 3 IACK

BOARD

SLOT

POSITION

1 2

Out Out

Sun 4300 CPU (1)

A A

3

In In

Memory (2)

In Out

Color (3)

In Out 1st MCP

In Out 2nd MCP

In Out 1st ALM-2

In Out 2nd ALM-2

Out Out

Ethernet (4)

A

A

B

B

B

A B

A

A B

A

A

In Out 1st IPC

(5)

In Out 2nd IPC

(5)

B

A

A

Reference

SPARCsystem 350 and 310 Cardcage Slot Assignments and Backplane Configuration

Procedures, 800-5722-10.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fc.htm [25.04.2002 16:11:33]

Sun4/I: Slot Assignment - Footnotes for Sun-4/310/330/350/360/370/380/390


Sun-4/310/330/350/360/370/380/390


1 501-1247

501-1374

501-1402

501-1443

501-1532






501-1316

501-1408

501-1466

501-1544

501-1565

501-1697

8MB Sun 4300 CPU

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

501-1742

501-1682

501-1739

32MB Sun 4300 CPU

4MB SIMM Module

4MB SIMM Module


2 501-1495

501-1563

501-1564

501-1408

501-1466

501-1544

501-1565

501-1697

48MB Memory Board

24MB Memory Board

8MB Memory Board

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

501-1703

501-1682

501-1739

32MB Memory Board

4MB SIMM Module

4MB SIMM Module


3 501-1116

501-1267

Sun-3 Color Frame Buffer



4 501-1153 Multibus Ethernet Controller Assembly


5 501-1125

501-1214

SunIPC w/o 80287

SunIPC w 80287 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00606.htm (1 von 3) [25.04.2002 16:11:44]


NOTE # PART #

6 501-1268

501-1139

GP2

GP+

BOARD


7 501-1381

501-1447




8 501-1316

501-1408

501-1466

501-1544

501-1565

501-1697

8MB Sun 4300 CPU

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module




10 501-1436

501-1723

501-1317

501-1711

501-1408

501-1466

501-1544

501-1565

501-1697

8MB Memory Board

8MB Memory Board

16MB Memory Board

16MB Memory Board

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

1MB SIMM Module

501-1704

501-1755

501-1682

501-1739

32MB Memory Board

32MB Memory Board

4MB SIMM Module

4MB SIMM Module


11 501-1666 Blank SCSI Adapter Assembly


12 501-1155 Xylogics 472 Tape Controller Assembly

NOTE # PART # BOARD http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00606.htm (2 von 3) [25.04.2002 16:11:44]


13

501-1166

501-1249


Xylogics 7053 Disk Controller


14 501-1249 Xylogics 7053 Disk Controller


15 501-1539

501-1855

ISP-80 IPI Disk Controller





Sun-4/330

SHUNTS

BOARD

SLOT POSITION

9U 6U 3U

BG3 IACK 1 2 3 4A 5A 4B 5B


(8)

A a

In

In

In

In

Out

Out

Out

Out

Out

Out

Out

Out

Out

Out

1st MCP

2nd MCP

1st ALM-2

2nd ALM-2

VX

MVX

GP

(6)

B A

B A

B A

B A

B A

A

A

In Out Color

(3)

In Out 1st HSI

In Out 2nd HSI

Out Out

Ethernet (4)

In Out IPC

Out Out

SCSI (9)

-

-

1st Memory (10)

2nd Memory

(10)

B A

B A

A

B A

B A

B A

A B

A

References

1. Sun-5 Slot Office Pedestal Cardcage Slot Assignments and Backplane Configuration

Procedures, 813-2068-11.

2. Sun-3 SCSI Host Adapter Installation Manual, 813-1015-11.

3. Cardcage Slot Assignments and Backplane Configuration Procedures for the VX and MVX

Accelerators, 800-5426-06.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fd.htm [25.04.2002 16:11:53]

Sun4/I: Slot Assigments - Sun-4/350

Sun-4/350

SHUNTS

BG3 IACK

BOARD

1

SLOT POSITION

2


(1)

A A

3 4 5 6

In In

Memory (2)

Out Out GP

(6)

Out Out CG9

In

In

In

In

In

In

TAAC-1

In Out 1st MCP

(7)

In Out 2nd MCP

In Out 1st ALM-2

In Out 2nd ALM-2

Out Out SunLink

Out Out Channel Adapter

Out

In

Out

In

1st Mapkit

Out

In

Out

In

2nd Mapkit

In

In

Out

Out

Color

(3)

CG5 w GP+

In Out CG5 wGP2

Out Out

Ethernet (4)

A

A

A B

A B

A B

E A B C D

D A B C

E A B C D

D A B C

D A B C

D A B C

D A

D

B

A

C

B C

C

E

C

C

A

A

A B

A B

B

B

C D

E

A

A B C

A

D

Out Out FDDI

In Out HSI

In Out

1st IPC (5)

In Out

2nd IPC (5)

E A B C D

E A B C D

E A B C D

D A B C

References

SPARCsystem 350 and 310 Cardcage Slot Assignments and Backplane Configuration

Procedures, 800-5722-10.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005fe.htm [25.04.2002 16:11:58]


Sun-4/360

SHUNTS

BG3 IACK

BOARD


(1)

A A

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

In In

Memory (2)

Out Out GP

(6)

A A

A

In Out CG9

In In GB

In

In

In

In

In

In

TAAC-1

(7)

Out Out ALM-1

In In

SCSI Adapter (11)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

1st Channel

Adapter

Out Out 2nd Channel

Out Out Adapter

Out Out

Ethernet (4)

A

A A

A

A

A

A A

A

K A B C D E F G H I J

J A B C D E F G H I

I

H

A B C D E F G H

A B C D E F G


J A B C D E F G H I

I

H

A B C D E F G H

A B C D E F G

A B

A

C

B

D

C

E

D

F

E

G

F

H

G H

A B C D E F

A B C D E F

E A B C D F G H I J K


(12)


(12)

Out Out

1st Disk Ctlr (13)

Out Out

2nd Disk Ctlr (13)

In Out Color

(3)

In Out CG5 w GP/GP+

In Out CG5 w GP2

A B C D E F

A B C D E

A B C D E F

A B C D E

K A B C D E F G H I

H A B C D E F G

J

A B

References

SPARCsystem 360 & SPARCserver 380 Cardcage Slot Assignments and Backplane Configuration

Procedures, 813-2088-11.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ff.htm (1 von 2) [25.04.2002 16:12:05]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ff.htm (2 von 2) [25.04.2002 16:12:05]


Sun-4/370

SHUNTS

BG3 IACK

BOARD


(1)

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

A a

In In

Memory (2)

A

Out

Out

In

Out

Out

Out

Out

Out

VX

MVX

CG9

GP

(6)

In In GB

In

In

In

In

In

In

TAAC-1

(7)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

Out

Out

Out

Out

Out

Out

Out

Out

1st Channel

Adapter

2nd Channel

Adapter

Out Out

SCSI (9)

A B C

A B

A B

A

A

A B

A

C

B

A

D

C

B

E

D

C

F

E

D

F

E F

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E

A B C D E F G H

A B C D E F G

A B

A

A B C D E F

A B C D E

C

B

D

C

A B

A

E

D

C

B

F

E

D

C

G

F G

E

D E

A B C D E F G H

Out Out

Ethernet (4)

Out Out

1st Disk Ctlr (13)

Out Out

2nd Disk Ctlr (13)


(14)


(14)

In Out Color

(3)

In Out CG5 w GP2

In Out CG5 w GP/GP+

Out Out FDDI

A B C D E F G H

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E

A B C D E F G H

A B

A B C D E

A B C D E F G H http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00600.htm (1 von 2) [25.04.2002 16:12:11]


References

1. SPARCsystem 370 Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2079-11.

2. Sun-3 SCSI Hosts Adapter Installation Manual, 813-1015-11.






Sun-4/380

SHUNTS

BG3 IACK

BOARD


(1)

A a

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

In In

Memory (2)

Out Out GP

(6)

A a

In

In

In

In

Out

-

Out

-

Out

In

In

In

Out

-

Out

-

CG9

In In GB

TAAC-1

(7)

Out Out 1st ALM-1

Out Out 2nd ALM-1

Out Out 3rd ALM-1

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

1st Channel

Adapter

2nd Channel

Adapter

In Out Color

(3)

In Out CG5 w GP2

In Out CG5 w GP/GP+

Out Out

Ethernet (4)

A

A B

A

A

A

A

A


A

A

J A B C D E F G H I

I A B C D E F G H

H A B C D E F G


J A B C D E F G H I

I A B C D E F G H

H

A B

A

A B C D E F G

C

B

D

C

E

D

F

E

G

F

H

G H

A B

A

C

B

D

C

E

D

F

E F

K A B C D E F G H I

H A B C D E F G

E A B C D F G H I

J

A B

J K


(12)


(12)

Out Out

1st Disk Ctlr (13)

Out Out

2nd Disk Ctlr (13)


(14)


(14)

A B C D E F

A B C D E

A B C D E F

A B C D E

A B C D

A B C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00601.htm (1 von 2) [25.04.2002 16:12:14]


References

SPARCsystem 360 & SPARCserver 380 Cardcage Slot Assignments and Backplane

Configuration Procedures, 813-2088-11.




Sun-4/390

SHUNTS

BG3 IACK

BOARD

Out Out

4300 CPU (1)

In In

Memory (2)

Out Out VX

Out Out MVX

Out Out GP2

In

In

In

In

In

In

TAAC-1

(7)

In Out 1st MCP

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

In Out 5th ALM-2

In Out 6th ALM-2

In Out 7th ALM-2

In Out 8th ALM-2

Out

Out

Out

Out

Out

Out

Out

Out

1st Channel

Adapter

2nd Channel

Adapter

Out Out

SCSI (9)

In Out 1st HSI

In Out 2nd HSI

Out Out

Ethernet (4)

Out Out 1st FDDI

Out Out 2nd FDDI

In Out

1st IPC (5)

In Out

2nd IPC (5)

In Out 3rd IPC

(5)

In Out 4th IPC

(5)

Out Out

1st IPI Ctlr (15)

Out Out

2nd IPI Ctlr (15)

A

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

A a

B

A

A

A

A B C D E F G H I J K

A B C D E F G H I J

A B C D E F G H I

A B C D E F G H


A B C D E F G H I J

A B

A

A B C D E F G H I

A B C D E F G H

A B C D E F G

A B C D E F

C

B

D

C

A B

A

E

D

C

B

F

E

D

C

A B C

A B

A B C D E

A B C D

G

F

E

D

H

G

F

E

I

H

G

F

I

J

H

J

G H



A B C D E F G H I J



A B C D E F G H I J


A B C D E F G H I

A B C D E F G H I

J

A B C D E F G H

A B C D E F G H I

A B C D E F G H I

J K

J http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00602.htm (1 von 2) [25.04.2002 16:12:22]


Out Out 3rd IPI Ctlr

(15)

Out Out 4th IPI Ctlr

(15)

In Out CG5

In Out CG5 w GP2

In Out CG9

A B C D E F G H I

A B C D E F G H


A B

A B

References

1. Sun SPARCserver 390 Card Cage Slot Assignments and Backplane Configuration Procedure,

813-2067-10.






Sun-4/470

SHUNTS

BG3 IACK

BOARD


In In

1st Memory (1)

A

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12

A a

In In 2nd Memory

(1)

In In

3rd Memory (1)

A

A

In In

4th Memory (1)

In In

5th Memory (1)

In In

6th Memory (1)

Out Out VX

Out Out MVX

Out Out GP2

In

In

In

In

In

In

TAAC-1

In Out 1st MCP

(2)

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

In Out 5th ALM-2

In Out 6th ALM-2

Out

Out

Out

Out

1st Channel

Adapter

Out

Out

Out

Out

2nd Channel

Adapter

Out Out

1st SCSI (3)

Out Out

2nd SCSI (3)

In Out 1st HSI

In Out 2nd HSI

Out Out 1st Ethernet

(4)

Out Out 2nd Ethernet

(4)

Out Out

3rd Ethernet (4)

Out Out 1st FDDI

Out Out 2nd FDDI

A

A

A

A B C D E F

A B C D E F G

A B C D E F

A B C D E F G

A B C D E F

A B C D E

A B C D E F G

A B C D E F

A B C

A B

A B

A

A

A

A B C D E F G

A B C D E F

A B C D E

A B C D

A B C D E F G

A B C D E F

A B C D E

A B

A

C

B

D

C

A B

A

C

B

A B C D

A B C

E

D

D

C

A B

F

E F

E

D E

A B C D E F G http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00603.htm (1 von 2) [25.04.2002 16:12:29]


Out Out 1st NC400

Out Out 2nd NC400

Out Out 3rd NC400

Out Out 4th NC400

Out Out

1st SMD Ctlr (5)

Out Out

2nd SMD Ctlr (5)

Out Out

1st IPI Ctlr (6)

Out Out

2nd IPI Ctlr (6)


(6)


(6)

In Out CG5

In Out CG5 w GP2

In Out CG9

In In Prestoserve

A B C D

A B C

A B

A

A B C D

A B C

A B C D

A B C

A B

A

A B C D

A B

A B

A B C D E F

References

1. Sun SPARCsystem 470 Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2102-14.





I: Slot Assignment - Footnotes for Sun-4/470/490


Sun-4/470/490


1 501-1402

501-1374

501-1532




501-1333

501-1721

32MB ECC Memory

128MB ECC Memory


2 501-1381

501-1447






4 501-1584 Sun 3E Ethernet Controller Assembly

NOTE # PART #

5 501-1249 Xylogics 7053

BOARD


6 501-1539

501-1855




7 501-1155 Xylogics 472 Tape Controller Assembly




Sun-4/490

SHUNTS

BG3 IACK

BOARD


In In

1st Memory (1)

A

SLOT POSITION

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

A a

In In 2nd Memory

(1)

In In

3rd Memory (1)

A

A

In In

4th Memory (1)

In In

5th Memory (1)

In In

6th Memory (1)

Out Out VX

Out Out MVX

Out Out GP2

In

In

In

In

In

In

TAAC-1

In Out 1st MCP

(2)

In Out 2nd MCP

In Out 3rd MCP

In Out 4th MCP

In Out 1st ALM-2

In Out 2nd ALM-2

In Out 3rd ALM-2

In Out 4th ALM-2

In Out 5th ALM-2

In Out 6th ALM-2

In Out 7th ALM-2

In Out 8th ALM-2

Out

-

Out

-

1st Channel

Adapter

Out

-

Out

-

2nd Channel

Adapter

Out Out

1st SCSI (3)

Out Out

2nd SCSI (3)

Out Out Tape Ctlr

(7)

In Out 1st HSI

In Out 2nd HSI

Out Out 1st Ethernet

(4)

Out Out 2nd Ethernet

(4)

A

A

A

A

A

A


A B C D E F G H I J

A B C D E F G H I

A B C D E F G H


A B C D E F G H I J

A B C D E F G H I

A A

B

C

B

A A

B

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E

C

D

C

B

E

D

C

D

E

F

E

D

G

F

E

F

A B C

A B

A B

A B C D

G

H

I

H J

I

J

G

F

G

H

I

H

I

A B C D E F G H I

A B C D E F G H I

A B C D E F G H I

A B C D E F G H I

J K

J

J K


A B C D E F G H I J


J http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00006/wcd00604.htm (1 von 2) [25.04.2002 16:12:40]


Out Out

3rd Ethernet (4)

Out Out 1st FDDI

Out Out 2nd FDDI

Out Out 1st NC400

Out Out 2nd NC400

Out Out 3rd NC400

Out Out 4th NC400

Out Out 5th NC400

Out Out 6th NC400

Out Out

1st IPI Ctlr (6)

Out Out

2nd IPI Ctlr (6)


(6)


(6)


(6)

In Out CG5

In Out CG5 w GP2

In Out CG9

Out Out

1st SMD Ctlr (5)

Out Out

2nd SMD Ctlr (5)

Out Out 3rd SMD Ctlr

(5)

Out Out

4th SMD Ctlr (5)

In In Prestoserve

A B C D E F G H I


A B C D E F G H I J

A B C D E F

A B C D E

A B C D

A B C

A B

A

A B C D E F G H

A B C D E F G

A B C D E F

A B C D E

A B C D

A B C D E F G H

A B

A B

A

B A

C B A

D C B A

A B C D E F G H I

References

1. Sun SPARCserver 490 Cardcage Slot Assignments and Backplane Configuration Procedures,

813-2087-14.





Sun4/I: Backplane - Contents

Backplane

Backplane Information

Sun-4/110/310

Sun-4/150/350

Sun-4/260/280/360/380

Sun-4/370

Sun-4/370/470 / SS670MP

Sun-4/330 / SS630MP

Sun-4/390/490 / SS690MP


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004bf.htm [25.04.2002 16:12:45]

Sun4/I: Backplane - Backplane Information

Backplane Information

This section contains bus signal charts and backplane layout illustrations.

VMEbus Backplane

Cardcage slot numbers are stamped, printed, or labeled on the sheet metal near the card ejectors.

VMEbus backplane jumpers are silk-screened on the cardcage as Px00, Px01, Px02, Px03, and Px04 or Jx00, Jx01, Jx02, Jx03, and Jx04; where x represents the card slot number.

These jumpers control VMEbus signals BUS GRANT 0-3 IN (BG0-3IN) to BUS GRANT 0-3 OUT

(BG0-3 OUT), and INTERRUPT ACKNOWLEDGE IN (IACKIN) to INTERRUPT

ACKNOWLEDGE OUT (IACKOUT). The VMEbus signals are referred to as BG0, BG1, BG2, BG3, and IACK in this section.

LABEL SIGNAL

Jxx0 Pxx0 BUS GRANT 0




Jxx4 Pxx4 INTERRUPT

ACKNOWLEDGE

ABBREVIATION

BG0

B01

BG2

BG3

IACK

VMEbus Signals

The VMEbus consists of signals on J1/P1 Row A, J1/P1 Row B, J1/P1 Row C, and J2/P2 Row B.

P2 Bus Signals

The Sun P2 Bus consists of signals on J2/P2 Row A, J2/P2 Row C, and J3/P3 Row B.

VMEbus J1/P1 Pinouts

PIN ROW A ROW B

1 D00

2 D01

BBSY*

BCLR*

3 D02

4 D03

5 D04

6 D05

ACFAIL*

BG0IN*

BG0OUT*

BG1IN*

ROW C

D08

D09

D10

D11

D12

D13

7 D06

8 D07

9 GND

BG1OUT* D14

BG2IN* D15

BG2OUT* GND http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (1 von 8) [25.04.2002 16:13:03]


10 SYSCLK BG3IN* SYSFAIL*

11 GND

12 DS1*

BG3OUT*

BR0*

BERR*

SYSRESET*

13 DS0* BR1*

14 WRITE* BR2*

15 GND BR3*

16 DTACK* AM0

LWORD*

AM5

A23

A22

17 GND

18 AS*

19 GND

20 IACK*

AM1

AM2

AM3

GND

A21

A20

A19

A18

21 IACKIN SERCLK A17

22 IACKOUT* SERDAT A16

23 AM4

24 A07

GND

IRQ7*

A15

A14

25 A06

26 A05

27 A04

28 A03

29 A02

30 A01

31 -12V

32 +5V

IRQ6*

IRQ5*

IRQ4*

IRQ3*

A13

A12

A11

A10

IRQ2*

IRQ1*

A09

A08

+5VSTDBY +12V

+5V +5V


PIN ROW A ROW B

1 User Defined +5

2 User Defined GND

ROW C

User Defined

User Defined

3 User Defined RESERVED User Defined

4 User Defined A24 User Defined

5 User Defined A25

6 User Defined A26

User Defined

User Defined

7 User Defined A27

8 User Defined A28

9 User Defined A29

10 User Defined A30

11 User Defined A31

12 User Defined GND

13 User Defined +5

14 User Defined D16

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (2 von 8) [25.04.2002 16:13:03]


15 User Defined D17

16 User Defined D18

17 User Defined D19

18 User Defined D20

19 User Defined D21

20 User Defined D22

21 User Defined D23

22 User Defined GND

23 User Defined D24

24 User Defined D25

25 User Defined D26

26 User Defined D27

27 User Defined D28

28 User Defined D29

29 User Defined D30

30 User Defined D31

31 User Defined GND

32 User Defined +5V

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined

User Defined


PIN ROW A ROW B ROW C

1 +5V User Defined GND


















19 +5V User Defined GND http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (3 von 8) [25.04.2002 16:13:03]








26 +12V User Defined +12V

27 +12V User Defined +12V

28 -12V User Defined -12V



31 -5V

32 -5V

User Defined -5V

User Defined -5V

Pressfit Backplanes

Pressfit Backplane production began in June 1987. Solderless contacts are machine pressed into plated-through holes on printed circuit boards. Component leads installed into the solderless contacts are held in place by a tapered entry, multi-finger contact design.

Cross Sectional View

Overhead View of Solderless Contact http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (4 von 8) [25.04.2002 16:13:03]


501-1354 5-Slot Backplane

Memory board options plug into connector J3, Slots 4 and 5, on the 501-1354 backplane. The Sun P2 bus connects Slots 1, 4, and 5 as shown below.

J102 Row A Connects to J403 Row A and J503 Row A

J102 Row C Connects to J403 Row C and J503 Row C

J103 Row B Connects to J403 Row B and J503 Row B

Cardcage Slots 4 and 5 share a private bus that connects signals between J2/P2, Row A and J2/P2,

Row C. These slots are used with 6U VMEbus boards.

The function of the backplane jumpers is shown below.

JUMPER CONNECTS

P2xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 2



501-1439, 501-1598, and 501-1832 12-Slot

Backplanes

The Sun P2 bus connects cardcage Slots 1 through 7 to each other, and cardcage Slots 10, 11, and 12 to each other.

In addition to the Sun P2 bus and the VMEbus, the 12-slot backplane has a private Internal bus that connects Slots 1, 2, and 3 as shown below.





J1/P1, Rows A, B, and C, on Slots 1, 2, and 3 are not connected to the VMEbus. Boards that use the

VMEbus cannot be used in Slots 1, 2, or 3. J2/P2, Row B, is connected between Slots 1 through 7.



The 501-1439 Backplane terminates J2/P2, Row C, Pins 75 and 96 with a 40.2 Ohm resistor and a

47pf capacitor.

The 501-1598 and 501-1832 Backplanes terminate J2/P2, Row C, Pins 75 and 96 with a 200 Ohm resistor. Termination is jumper selectable.

The Sun 4400 CPU is not supported in the 501-1439 Backplane.


JUMPER CONNECTS

J4xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 4









501-1498 and 501-1597 16-Slot Backplanes

The Sun P2 bus connects cardcage Slots 1 through 7 to each other, cardcage Slots 11 and 12 to each other, and cardcage Slots 13, 14, and 15 to each other.

In addition to the Sun P2 bus and the VMEbus, the 16-slot backplane private internal bus connects

Slots 1, 2, and 3 as shown below.





J1/P1 Rows A, B, and C on Slots 1, 2, and 3 are not connected to the VMEbus. Boards that use the

VMEbus cannot be used in Slots 1, 2, or 3. J2/P2, Row B, is connected between Slots 1 through 7.

The 501-1498 Backplane must be 501-1498-02 or greater when used with the Sun 4400 CPU.


JUMPER CONNECTS






J7xx BG0-3IN to BG0-3Out and IACKIN to IACKOUT on slot 7 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (6 von 8) [25.04.2002 16:13:03]











Backplane Sun P2 or Private Bus Connection

Backplane slots that share an adjacent P2 bus are marked with the same letter in the charts below.

3-Slot VMEbus Backplane

501-1127

Slot 1 2 3

P2 Bus A A A


501-1354

Slot 1 2 3 4 5 6 7

P2 Bus A B B C D A A


501-1128

Slot 1 2 3 4 5 6

P2 Bus A A A A B B


501-1092 and 501-1117

Slot 1 2 3 4 5 6 7 8 9 10 11 12

P2 Bus A A A A A A B C D E E E


501-1439, 501-1598, and 501-1832

Slot 1 2 3 4 5 6 7 8 9 10 11 12 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f6.htm (7 von 8) [25.04.2002 16:13:03]


P2 Bus A A A A A A A B C D D D


501-1498 and 501-1597

Slot 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16

P2 Bus A A A A A A A B C D E E F F F G



Sun4/I: Backplane - Sun-4/110/310

Sun-4/110/310

501-1127

Pressfit

Power:

1.3 Amps @ +5Vdc

6.5 Watts

P1 Power Pinouts

1-2 3-4 5 6 7 8

-5 GND +12 GND -12 GND




Sun-4/150/350

501-1128

Pressfit

Power:

1.3 Amps @ +5Vdc

6.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004f8.htm (1 von 2) [25.04.2002 16:13:13]


P1 Power Pinouts

1-2 3-4 5 6 7 8

-5 GND +12 GND -12 GND



Sun4/I: Backplane - Sun-4/260/280/360/380

Sun-4/260/280/360/380

501-1092 501-1117

Pressfit

Power

1.3 Amps @ +5Vdc

6.5 Watts



Sun4/I: Backplane - Sun-4/370

Sun-4/370

501-1439

Pressfit

Test Points Description

TEST

POINT DESCRIPTION

TEST


1 +5

2 GND

5

6

+12

-5.2

3 +12 Motor

4 -12

7 Chassis ground

8 Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fa.htm (1 von 2) [25.04.2002 16:13:22]

Sun4/I: Backplane - Sun-4/370

Power

2.1 Amps @ +5Vdc

10.5 Watts

Note

The LED positions on the backplane and the descriptions molded into the front cover do not match.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fa.htm (2 von 2) [25.04.2002 16:13:22]

Sun4/I: Backplane - Sun-4/370/470 / SS670MP

Sun-4/370/470 / SS670MP

501-1598

Pressfit


TEST


TEST


1 +5 5 +12

2 GND

3 +12 Motor

4 -12

6

7

8

-5.2

Chassis ground

Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (1 von 3) [25.04.2002 16:13:30]


Power

2.1 Amps @ +5Vdc

10.5 Watts

Sun-4/370/470 / SS670MP

501-1832

Pressfit


TEST


TEST

POINT DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (2 von 3) [25.04.2002 16:13:30]


1 +5

2 GND

3 +12 Motor

4 -12

5 +12

6 -5.2

7 Chassis ground

8 Ground

Power:

2.1 Amps @ +5Vdc

10.5 Watts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fb.htm (3 von 3) [25.04.2002 16:13:30]

Sun4/I: Backplane - Sun-4/330 / SS630MP

Sun-4/330 / SS630MP

501-1354

Pressfit

Power

2.0 Amps @ +5Vdc

10.0 Watts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fc.htm [25.04.2002 16:13:36]


Sun-4/390/490 / SS690MP

501-1498

Pressfit


TEST


TEST


1 +5

2 GND

5

6

+12

-5.2

3 +12 Motor

4 -12

7 Chassis ground

8 Ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (1 von 3) [25.04.2002 16:13:44]


Power

2.1 Amps @ +5Vdc

10.5 Watts

Sun-4/390/490 / SS690MP

501-1597

Pressfit


TEST


TEST


1 +5 5 +12 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (2 von 3) [25.04.2002 16:13:44]


2 GND

3 +12 Motor

4 -12

6 -5.2

7 Chassis ground

8 Ground

Power

2.1 Amps @ +5Vdc

10.5 Watts

Note

The Load Resistor is only used with the 925W power supply.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004fd.htm (3 von 3) [25.04.2002 16:13:44]

Sun4/I: Miscellaneous - Contents

Miscellaneous

Floating Point Unit-2 (FPU2)

SunIPC

6U to 9U VMEbus Adapter

VMEbus to Multibus Adapter


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004bc.htm [25.04.2002 16:13:46]

Sun4/I: Miscellaneous - Floating Point Unit-2 (FPU2)

Floating Point Unit-2 (FPU2)

Sun-4/110/150

Option 154

501-1384

4/110/150 Option Parts

Front Bracket

Rear Bracket

4-40 Screw

340-1743

340-2163

240-1196

J100 Jumper Settings

PINS SETTING DESCRIPTION

1-2

3-4

5-6

7-8

In

In

In

Out

TI chip on board

No Tristate on all output

TI8847/TI8837

Enable chaining mode http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a5.htm (1 von 3) [25.04.2002 16:13:52]


Notes

1. The 501-1384 FPU2 is supported only on CPU boards 501-1512, 501-1513, 501-1514,

501-1515, 501-1516, and 501-1517.

2. Remove the Weitek ALU (U202) and Multiplier (U201) from the 4/110/150CPU to install the

FPU2.

3. Diagnostics fpurel and fputest for SunOS 4.0 and 4.0.1 are on the 1.0 FPU2 Patch Tape.

Reference

FPU-2 Installation Manual for Sun-4/100 Systems, 800-3067.

Floating Point Unit-2 (FPU2)

Sun-4/260/280

Option 154

501-1387 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a5.htm (2 von 3) [25.04.2002 16:13:52]


J100 Jumper Settings


1-2

3-4

5-6

7-8

In

In

In

Out

TI chip on board

No Tristate on all output

TI8847/TI8837

Enable chaining mode

Note

Diagnostics fpurel and fputest for SunOS 4.0 and 4.0.1 are on the 1.0 FPU2 Patch Tape.

Reference

FPU-2 Installation Manual for Sun-4/100 Systems, 800-3067.



Sun4/I: Miscellaneous - SunIPC

SunIPC

Sun-4/260/280/330/360/370/380/390

Options SUNIPC / SUNIPC-87

501-1125 501-1214 w/o 80287 w 80287 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a6.htm (1 von 3) [25.04.2002 16:13:59]


Power:

5.6 Amps @ +5Vdc

28.0 Watts

Jumper and Switch Settings

JUMPER SETTING

H05 1-2 In

DESCRIPTION

Enable 48MHz XTAL

H06 1-2

H10 1-2

In

Out

In

Enable 20 MHz XTAL

For 501-1214 with 80287

For 501-1125 without 80287

H11 1-2 Out Enable XTAL1

VME Address 380000; device pc0

SWITCH SETTING DESCRIPTION

SW3-1

SW3-2

SW3-3

SW3-4

SW3-5

SW3-6

SW3-7

SW3-8

On

On

Off

Off

Off

On

On

On

A23

A22

A21

A20

A19

A18

A17

A16

VME Address 3C0000; device pc2


SW3-1

SW3-2

SW3-3

SW3-4

SW3-5

SW3-6

SW3-7

SW3-8

On

On

Off

Off

Off

Off

On

On

A23

A22

A21

A20

A19

A18

A17

A16

VME Address 3A0000; device pc1

SWITCH SETTING DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a6.htm (2 von 3) [25.04.2002 16:13:59]


SW3-1

SW3-2

SW3-3

SW3-4

SW3-5

SW3-6

SW3-7

SW3-8

On

On

Off

Off

Off

On

Off

On

A23

A22

A21

A20

A19

A18

A17

A16

VME Address 3E0000; device pc3


SW3-1

SW3-2

SW3-3

SW3-4

SW3-5

SW3-6

SW3-7

SW3-8

On

On

Off

Off

Off

Off

Off

On

A23

A22

A21

A20

A19

A18

A17

A16

Notes

1. The Sun 3200 CPU must be >=501-1100-08 or >=501-1206-06.

2. Boards with Aeroscientific FAB date code 8639 may randomly exhibit "interrupt level2" errors.



Sun4/I: Miscellaneous - 6U to 9U VMEbus Adapter

6U to 9U VMEbus Adapter

Option 160A

501-1269 with P2A & P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a7.htm (1 von 2) [25.04.2002 16:14:05]

Sun4/I: Miscellaneous - 6U to 9U VMEbus Adapter

6U to 9U VMEbus Adapter

Option 160B

501-1191 without P2A & P2C



Sun4/I: Miscellaneous - VMEbus to Multibus Adapter

VMEbus to Multibus Adapter

Option 161

501-1054

Power:

2.0 Amps @ +5Vdc

10.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005a8.htm (1 von 2) [25.04.2002 16:14:11]

Sun4/I: Miscellaneous - VMEbus to Multibus Adapter

Note:

There are no LED, switch, or cable openings in the backpanel.



Sun4/I: Communication - Contents

Communication

Multibus

Sun-2 Ethernet Controller

VMEbus to Multibus Adapter with Sun-2 Ethernet

Sun-3/E Ethernet Assembly

Systech MTI-800/1600 Controller

Systech MTI-850/1650 Controller

VMEbus to Multibus Adapter with MTI-1600

VMEbus to Multibus Adapter with MTI-1650

VMEbus to Multibus Adapter with MTI-1650A

VMEbus

MAPKIT

Asynchronous Line Multiplexor-2

Multiprotocol Communication Processor

SunLink Channel Adapter

High-speed Serial Interface (HSI)

FDDI/DX

Sun Network CoProcessor


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004b9.htm [25.04.2002 16:14:14]

Sun4/I: Communication - Sun-2 Ethernet Controller

Sun-2 Ethernet Controller

Sun-4/110/150/260/280

Sun-4/310/330/350/360/370/380/390

Option 450

501-1004

Power:

6.0 Amps @ +5Vdc

0.5 Amps @ +12Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00512.htm (1 von 2) [25.04.2002 16:14:18]

Sun4/I: Communication - Sun-2 Ethernet Controller

36.0 Watts


JUMPER PINS SETTING DESCRIPTION

J101 1-2

1-2

In

Out

Level 1 Ethernet

Level 2 Ethernet

J400 1-2

J401 1-2

J500 1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

Out

Out

Out

Out

Out

Hardwired

Out

Out

Out

Out

M.BIG Select

M.EXP Select

Interrupt level 0

Interrupt level 1

Interrupt level 2

Interrupt level 3

Interrupt level 4

Interrupt level 5

Interrupt level 6

Interrupt level 7

Switch Settings for VMEbus Controller ie1

DIP SWITCH 1 2 3 4 5 6 7 8

U503

U505

Off

Off

Off

Off

Off

On

On

Off

Off

Off

Off

Off

Off

Off

On

Off

U506 Off On On Off Off On On Off

Note:

The Sun-2 Ethernet Controller is not supported in Solaris >=2.2.



Sun4/I: Communication - VMEbus to Multibus Adapter

VMEbus to Multibus Adapter with Sun-2 Ethernet

Sun-4/110/150/260/280/310/330/350/360

Sun-4/370/380/390

Option 450

501-1153 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00513.htm (1 von 2) [25.04.2002 16:14:33]


Power:

5.8 Amps @ +5Vdc

29.0 Watts

VME TO MULTIBUS ADAPTER BOARD SWITCH SETTINGS

SWITCH 1 2 3 4 5 6 7 8 DESCRIPTION

U1 N/C ON ON ON ON ON ON ON I-O Address = 0x00

U2 N/C OFF OFF OFF OFF OFF OFF OFF I-O Space = No response

U3 ON ON ON ON ON ON ON ON I-O Address = 0x00

U4 OFF OFF OFF OFF OFF OFF OFF OFF VME I-O Space = No response

U5 OFF OFF OFF OFF OFF OFF OFF OFF 24-Bit Memory Address Space

U6 OFF OFF OFF OFF OFF OFF OFF OFF 24-Bit Memory Block Size

U7 OFF OFF OFF ON OFF OFF OFF OFF 24-Bit Memory Address Space

U8 ON ON ON ON OFF OFF OFF OFF 24-Bit Memory Block Size

U9 OFF OFF OFF OFF OFF OFF OFF OFF No connection


U11 OFF OFF OFF OFF OFF OFF OFF OFF Sets Address Bits A23 - A20

U12* OFF

OFF

ON

OFF

OFF

ON

ON

OFF

OFF

OFF

OFF

ON

OFF

ON

ON

ON

Interrupt Vector = 0x75

Interrupt Vector = 0x1B

J1

PINS 1-2 IN If BCLK is desired

PINS 3-4 IN If CCLK is desired

* For SunOS 3.0 and above, use 0x75. For SunOS below 3.0, use 0x1B.



Sun4/I: Communication - Sun-3/E Ethernet Assembly

Sun-3/E Ethernet Assembly

Sun-4/390/470/490

Option 452

501-1584

Power:

4.1 Amps @ +5Vdc

20.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00514.htm (1 von 3) [25.04.2002 16:14:38]


Notes

1. Board revision 501-8027-06 or 501-1584-01 is required for use in any SPARC CPU based system.

2. When used with the Sun-4400 CPU, 501-1381, the board revision must be >=501-8027-07 or the assembly must be >=501-1584-02.

Switch and Jumper Settings

DIP SWITCH SWITCH SETTING DESCRIPTION

SW0601 1-7

1-7

On

Off

Not Supported

Enable Ethernet*

SW0201

7

8

5

6

3

4

1

2

Off

Off/On

*

*

*

Off

On

On

24/32-bit addressing

N/C

A18 address decode

A19 address decode

A20 address decode

A21 address decode

A22 address decode

A23 address decode

*DIP Switch SW0201 settings for ie2, ie3, and ie

SW0201 SWITCH 3 SWITCH 4 SWITCH 5 ADDRESS

1st Board On On Off 31ff02

2nd Board

3rd Board

Off

Off

On

Off

Off

On

35ff02

2dff02


SW0202

SW0202

1

2

On

On

A24 address decode

A25 address decode

SW0202

SW0202

SW0202

SW0202

SW0202

SW0202

3

4

5

6

7

8

On

On

On

On

On

On

A26 address decode

A27 address decode

A28 address decode

A29 address decode

A30 address decode

A31 address decode


J0201 1-2

J0601 1-2

In

In

Clock enable

Level 1 Ethernet

J0601 1-2

J0602 1-2

Out Level 2 Ethernet

Out VCC to Pin-7 disabled http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00514.htm (2 von 3) [25.04.2002 16:14:38]


Reference

Sun SunNet Ethernet/VME Controller Configuration Procedures, 813-2082-10.



Sun4/I: Communication - Systech MTI-800/1600 Controller

Systech MTI-800/1600 Controller

Asychronous Line Multiplexer 1 (ALM-1)

Sun-4/260/280

Options 480 / 481



Switch Settings mt0 Defaults

DIP SWITCH SETTING DESCRIPTION

SW2

7

8

5

6

3

4

1

2

Off

Off

Off

Off

Off

On

On

Off

Address select A15

Address select A14

Address select A13

Address select A12

Address select A11

Address select A10

Address select A9

Address select A8

SW3

SW4

7

8

5

6

3

4

1

2

7

8

5

6

1

2*

3*

4

Off

Off

On

On

On

On

On

Off

Off

Off

On

Off

Off

Off

Off

On

Address select A7

Address select A6

Address select A5

Address select A4

Address select A3

Select 16-bit addresses

One stop bit

One stop bit

Odd parity

No parity

8-bit characters

8-bit characters

9600 baud

9600 baud

9600 baud

9600 baud

SW5

7

8

5

6

3

4

1

2

Off

Off

Off

Off

On

Off

Off

Off

Interrupt level 0

Interrupt level 1

Interrupt level 2

Interrupt level 3

Interrupt level 4

Interrupt level 5

Interrupt level 6

Interrupt level 7

* mti0 at 0x0620, Dip SW3, Switch-2, ON, Switch-3, ON mti1 at 0x0640, Dip SW3, Switch-2, ON, Switch-3, OFF mti2 at 0x0660, Dip SW3, Switch-2, ON, Switch-3, ON




Systech MTI-850/1650 Controller

Asychronous Line Multiplexer 1 (ALM-1)

Sun-4/260/280

Options 480 / 481



Switch Settings mt0 Defaults


SW2

7

8

5

6

3

4

1

2

Off

Off

Off

Off

Off

On

On

Off

Address select A15

Address select A14

Address select A13

Address select A12

Address select A11

Address select A10

Address select A9

Address select A8

SW3

SW4

7

8

5

6

3

4

1

2

7

8

5

6

1

2*

3*

4

Off

Off

On

On

On

On

On

Off

Off

Off

On

Off

Off

Off

Off

On

Address select A7

Address select A6

Address select A5

Address select A4

Address select A3

Select 16-bit addresses

One stop bit

One stop bit

Odd parity

No parity

8-bit characters

8-bit characters

9600 baud

9600 baud

9600 baud

9600 baud

SW5

7

8

5

6

3

4

1

2

Off

Off

Off

Off

On

Off

Off

Off

Interrupt level 0

Interrupt level 1

Interrupt level 2

Interrupt level 3

Interrupt level 4

Interrupt level 5

Interrupt level 6

Interrupt level 7

* mti0 at 0x0620, Dip SW3, Switch-2, ON, Switch-3, ON mti1 at 0x0640, Dip SW3, Switch-2, ON, Switch-3, OFF mti2 at 0x0660, Dip SW3, Switch-2, ON, Switch-3, ON

SHUNT SETTINGS DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00516.htm (2 von 3) [25.04.2002 16:14:45]


W1

W2

W3

W4

W5

W6

W7

Out

Out

In

Out

Out

In

In

+12Vdc routing to data cable disabled

-12Vdc routing to data cable disabled

Normal transfer acknowledge delay

Extra 100 nsec delay during transfer acknowledge

Byte swap enable

Byte swap disable

Enable BPRO

References

1. Sun-3/180 16-Channel Asynchronous Line Multiplexer Configuration Procedures, 813-2008.

2. Asynchronous Line Multiplexer Configuration Procedures, 813-2003.




VMEbus to Multibus Adapter with Systech MTI-1600

Sun-4/260/280

Option 481

501-1157-01 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00517.htm (1 von 2) [25.04.2002 16:14:50]


Power:

7.1 Amps @ +5Vdc

0.6 Amps @ +12Vdc

0.4 Amps @ -12Vdc

47.5 Watts




VMEbus to Multibus Adapter with Systech MTI-1650

Sun-4/260/360

Option 481

501-1157-02 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00518.htm (1 von 3) [25.04.2002 16:14:56]


Power:

7.1 Amps @ +5Vdc

0.6 Amps @ +12Vdc

0.4 Amps @ -12Vdc

47.5 Watts



U1* N/C ON ON ON ON ON OFF OFF I-O Address

U2 N/C ON ON ON ON ON OFF OFF I-O Space = 2

U3 ON ON ON ON ON OFF OFF ON I-O Address = 0xEE

U4 ON ON ON ON ON OFF OFF ON VME I-O Space

U5 ON ON ON ON ON ON ON ON 24-Bit Memory Address Space






U11 OFF OFF OFF OFF ON ON ON ON Sets Address Bits A23 - A20

U12* ON ON ON ON OFF ON ON OFF Interrupt Vector


J1


* mti1, U1, 2,4,5,6, ON, U12, 2,3,5,6,7, ON mti2, U1, 2,5,6, ON, U12, 1,3,5,6,7, ON http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00518.htm (2 von 3) [25.04.2002 16:14:56]





VMEbus to Multibus Adapter with Systech MTI-1650A

Sun-4/260/280/360/380

Option 481

501-1165

Power:

7.1 Amps @ +5Vdc

0.6 Amps @ +12Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00519.htm (1 von 2) [25.04.2002 16:15:03]


0.4 Amps @ -12Vdc

47.5 Watts



U1* N/C ON ON OFF ON ON OFF OFF I-O Address

U2 N/C ON ON ON ON ON OFF OFF I-O Space = 2

U3 ON ON ON ON ON OFF OFF ON I-O Address = 0xEE

U4 ON ON ON ON ON OFF OFF ON VME I-O Space







U11 OFF OFF OFF OFF ON ON ON ON Sets Address Bits A23 - A20

U12* ON ON ON OFF ON ON ON OFF Interrupt Vector


J1


* mti1, U1, 2,4,5,6, ON, U12, 2,3,5,6,7, ON mti2, U1, 2,5,6, ON, U12, 1,3,5,6,7, ON



Sun4/I: Communication - MAPKIT

MAPKIT

Sun-4/260/280/390

501-1202

Notes

1. Install the Token Bus Controller in the left slot of the adapter.

2. Install the Token Bus Modem in the right slot of the adapter.

3. The Token Bus Controller and Token Bus Modem are sold by INI.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051a.htm (1 von 2) [25.04.2002 16:15:07]

Sun4/I: Communication - MAPKIT

Jumper Settings

JUMPER PINS VALUE DESCRIPTION

J1 1-2

4-6

5-7

9-11

3 Bus request level

J2

J3

J4

3-5

4-6

3 Bus request level

3-4 16 sec Watchdog timer

J5

1-2

3-4

5-6

7-8

11-12

13-14

0x900 Short I/O address

9-10 Bus Boot Boot configuration

J6

J7

J8

J9

J13

5-6

9-10

1-2

2-1

1-2

3

3

512K

VME host interrupt

VME host interrupt

Memory size

Normal Clock parameters

Normal Clock parameters

Power:

4.9 Amps @ +5Vdc

0.3 Amps @ +12Vdc

0.1 Amps @ -12Vdc

29.3 Watts

Reference:

Sun MAPkit Board Configuration Procedures, 813-2029.



Sun4/I: Communication - Asynchronous Line Multiplexor-2

Asynchronous Line Multiplexor-2

Sun-4/110/150/260/280

Sun-4/310/330/350/360/370/380/390/470/490

SS600MP

501-1203

Power:

7.0 Amps @ +5Vdc

0.2 Amps @ -5Vdc

36.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051b.htm (1 von 3) [25.04.2002 16:15:32]



JUMPER PINS SETTING

J0201 1-2 In

DESCRIPTION

Test jumper for oscillator

J0202 32 Bit In

J0202 24 Bit Out

VME address bus size

J1501 RS-232 In Enables RS-232 for ALM-2

J1501 RS-449 Out Not used for ALM-2

J1502 RS-232 In Enables RS-232 for ALM-2

J1502 RS-449 Out Not used for ALM-2

J1503 1-2 In Test jumper for oscillator

ADDRESS BIT A

1

6

DIP SWITCH S0201

A

1

7

A

1

8

A

1

9

A

2

0

A

2

1

A

2

2

A

2

3

A

2

4


A

2

5

A

2

6

A

2

7

A

2

8

A

2

9

A

3

0

A

3

1

SWITCH and SETTING 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 mcp0 @ 0x01000000 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp1 @ 0x01010000 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp2 @ 0x01020000 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp3 @ 0x01030000 0 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp4 @ 0x02000000 1 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 mcp5 @ 0x02010000 0 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 mcp6 @ 0x02020000 1 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 mcp7 @ 0x02030000 0 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1

0 = Off

1 = On

Notes

1. The Sun-3/110 and Sun 3004 CPU must be 501-1134-06, 501-1163-09, 501-1164-09, or greater. All 501-1208 and 501-1209 revisions are usable.

2. When four or more ALM-2 boards are installed in a system, the part number must be

>=501-1203-05 because of the mechanical fit of the data cables.

3. An addressing conflict can occur between the ALM-2, MCP, and ALM-1. Refer to the VME

Installation Notes in the Slot Assignments chapter.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051b.htm (2 von 3) [25.04.2002 16:15:32]


Reference

Asynchronous Line Multiplexor-2 Configuration Procedures, 813-2042.



Sun4/I: Communication - Multiprotocol Communication Processor

Multiprotocol Communication

Processor

Sun-4/110/150/260/280

Sun-4/310/330/350/360/370/380/390/470/490

SS600MP

501-1221

Power:

7.0 Amps @ +5Vdc

0.2 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051c.htm (1 von 2) [25.04.2002 16:15:36]

Sun4/I: Communication - Multiprotocol Communication Processor

36.0 Watts




J0202 32 Bit

J0202 24 Bit

In

Out

VME address bus size

J1501 RS-232 Out Not used for MCP

J1501 RS-449 In Enables RS-449 Port 0

J1502 RS-232 Out Not used for MCP

J1502 RS-449 In Enables RS-449 Port 1


ADDRESS BIT

A

1

6


A

1

7

A

1

8

A

1

9

A

2

0

A

2

1

A

2

2

A

2

3

A

2

4


A

2

5

A

2

6

A

2

7

A

2

8

A

2

9

A

3

0

A

3

1

SWITCH and SETTING 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 mcp0 @ 0x01000000 1 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp1 @ 0x01010000 0 1 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp2 @ 0x01020000 1 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1 mcp3 @ 0x01030000 0 0 1 1 1 1 1 1 0 1 1 1 1 1 1 1

0 = Off

1 = On

Notes


2. The MCP is not supported in Solaris >=2.2.

3. An addressing conflict can occur between the MCP, ALM-1, and ALM-2. Refer to the VME

Installation Notes in the Slot Assignment chapter.

Reference:

MCP Configuration Procedures, 813-2032.



Sun4/I: Communication - SunLink Channel Adapter

SunLink Channel Adapter

Sun-4/260/280/350/360/370/380/390/470/490

SS670MP / SS690MP

370-1128 501-1460

Board Set Board Set

Backpanel and Connectors

Power:

8.6 Amps @ +5Vdc

43.0 Watts

Notes

1. Replace 370-1128 with 501-1460. Refer to FCO A0003-1.


3. In Sun-3/2XX systems with multiple SCA boards, the CPU must be 501-1100-08, 501-1206-06, or greater.

4. The SunLink Channel Adapter must be >=501-1460-02 for use with the Sun 3400 CPU.

5. The Sun FDDI Board must be >=501-1276-02 for use with the SunLink Channel Adapter.

6. SunLink Release 7.0 Channel Gateway is required for use with the Sun 3400 CPU.

7. The Sun 3400 CPU must be >=501-1550-10 for use with the SunLink Channel Adapter.

8. The Sun 4200 CPU, 501-1274 must be >=501-1274-13 for use with the SunLink Channel

Adapter.

9. The SunLink Channel Adapter is not supported in Solaris >=2.2.



Reference

SunLink Channel Adapter Configuration Procedures, 813-2040-10.

CIO Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (2 von 5) [25.04.2002 16:15:57]


IBD Board

Jumper Settings

JUMPER PINS SETTING

B1C 7-8

Others

In

Out

DESCRIPTION

VME bus request level BR gives level 3

B1A

B6C

2-3

6-7

10-11

13-14

15-16

All

In

In

In

In

In

Bus grant In/Out BG0/BG3 gives level 3

Out VME bus data transfer timeout http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (3 von 5) [25.04.2002 16:15:57]


B8P

B8U

B8V

7-8

3-4

5-6

7-8

1-2

3-4

5-6

7-8

1-2

3-4

5-6

7-8

In

Out

Out

Out

In

Out

Out

Out

In

Out

Out

Out

Local processor external bus page selection BS gives page 0

Interrupt acknowledge page selection

IACK gives page 0

Interrupt request page selection IREQ gives page 0 and must be the same as

IACK

LCP Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051d.htm (4 von 5) [25.04.2002 16:15:57]


Jumper Settings


JM01 All

JM02 All

Out

Out

DESCRIPTION

VME BERR timeout 67.1 seconds

VME LBERR timeout 107.4 seconds

JM03 2-4

3-5

JM04 1-2*

3-4

5-6

7-8

JM05 1-2

3-4

5-6

7-8

JM06 2-3

6-7

10-11

13-14

15-16

In

In

Out*

Out

Out

Out

Out

Out

Out

In

In

In

In

In

In

SYSRESET Out disabled

SYSRESET In disabled

1-2, Out, for 1st board (chat0)

1-2, In, for 2nd board (chat1)

Bus request level 0

Bus request level 1

Bus request level 2

Bus request level 3

Select bus grant 3

JM07 1-2

JM08 1-2

3-4

5-6

7-8

9-10

JM09 1-2

2-3

JM10 1-2

2-3

JM11 1-2

JM12 1-2

JM14 1-2

2-3

In

Out

Out

Out

In

Out

In

Out

In

Out

Local DTACK delay 100ns

Unclaimed grant timeout 262ms

EPROM size 128KB

Arbitration - release when done

Out System controller function enabled

Out VMEbus priority arbitration

Out

In

Minimum address strobe 60ns



Sun4/I: Communication - High-speed Serial Interface (HSI)

High-speed Serial Interface (HSI)

Sun-4/110/150/260/280/330/350/390/470/490

501-1338

Power:

5.3 Amps @ +5Vdc

0.3 Amps @ -5Vdc

28.1 Watts

Notes

1. SCSI-3 Host Adapter must be >=501-1120-07, >=501-1170-07, >=501-1217-04, or

>=501-1236-03.

2. Sun-3/110 CPU must be >=501-1134-06.

3. Sun-3/140/150/160/180 CPU must be >=501-1074-22, >=501-1094-22, >=501-1163-09, http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051e.htm (1 von 3) [25.04.2002 16:16:02]


>=501-1164-09, or any revision of 501-1208.

4. The minimum operating system is SunOS 4.0.

5. The High-speed Serial Interface is not supported in Solaris >=2.2.

Reference

SunLink HSI Board Installation/Service Manual, 813-1046-10.


DIP

SWITCH SWITCH SETTING DESCRIPTION

SW020*

7

8

5

6

3

4

1

2

Off

On

On

On

On

On

On

On

Base address select A24








SW0203*

SW1301

7

8

5

6

3

4

1

2

7

8

5

6

3

4

1

2

On

On

Off

On

On

On

On

On

On

Off

On

On

On

On

On

On









Interrupt level 1

Interrupt level 2

Interrupt level 3

Interrupt level 4

Interrupt level 5

Interrupt level 6

Interrupt level 7

Not used

* The first HSI address is 0x01200000.

* The second HSI address is 0x01400000.

** SW-6 is ON and SW-7 is OFF for a second HSI.

Jumper U1103


1-2 In Clock enable http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051e.htm (2 von 3) [25.04.2002 16:16:02]




Sun4/I: Communication - FDDI/DX

FDDI/DX

Sun-4/110/150/260/280/330/350/390/470/490

SS630MP / SS670MP / SS690MP

Option 461

501-1276

Power:

11.2 Amps @ +5Vdc

0.1 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051f.htm (1 von 3) [25.04.2002 16:16:12]


1.9 Amps @ +12Vdc

0.7 Amps @ -12Vdc

87.7 Watts

Switch Settings

Notes

1. Use 2A subminiature Fuse 150-1174.

2. The Sun 3004 CPU must be 501-1163-09, 501-1164-09 or greater. All 501-1208 revisions are usable.

3. 501-1276-02 or greater is required for use with the SunLink Channel Adapter board.

4. The Sun-4/330 requires Power Supply 300-1072.

5. Set the FDDI Controller Switch 1, Dip 1, to ON if the DMA uses 32-bit addresses. All Sun systems use 32-bit DMA.

6. Set the FDDI Controller Switch 1, Dip 1, to OFF if the DMA uses 24-bit addresses.

Release Notes

1. Diskless booting requires CPU EPROM 3.0 or greater.

2. The minimum operating system is SunOS 4.0.3.

3. The FDDI/DX is not supported in Solaris >=2.2.

Reference

SunLight FDDI Dual-Attach Controller Card Configuration and Installation Manual,

813-1053.

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0051f.htm (2 von 3) [25.04.2002 16:16:12]



Sun4/I: Communication - Sun Network CoProcessor

Sun Network CoProcessor

Sun-4/470/490

SS630MP / SS670MP / SS690MP

Option 176

370-1396 / 370-1421 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (1 von 8) [25.04.2002 16:16:35]


Power:

8.0 Amps @ +5Vdc

0.5 Amps

46.0 Watts

Interphase Release 1.4 Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (2 von 8) [25.04.2002 16:16:35]


Address Switches and Address Bit Assignments

DIP SWITCH 1 2 3 4 5 6 7 8

SW1 A15 A14 A13 A12 A11 A10 A09 AM

SW2

SW3

A23 A22 A21 A20 A19 A18 A17 A16

A31 A30 A29 A28 A27 A26 A25 A24

SNC 1.0 and SNC 1.2 Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (3 von 8) [25.04.2002 16:16:35]


Notes

1. SNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01.

2. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-10, and 525-1025-10. This firmware is installed on ISP-80 IPI Controller 501-1539-10 and 501-1855-04.

3. Under Interphase Release 1.4, the VME address space of the fifth NC400 and the Prestoserve board is at 0x800000. If both Prestoserve (pr0) and a fifth NC400 (ne4) are installed, change the address of pr0 to 0xc00000 on the Prestoserve board and in the kernel.

When the Prestoserve is set to 0xc00000, the alternate 24-bit settings for the NC400 at

0xc00000 - 0xc7ffff and 0xc80000 - 0xcfffff cannot be used.

When the Prestoserve is set to 0xc00000, the address space 0xc00000 - 0xcfffff, reserved for large OEM/user devices, is used.

4. SunOS for the Sun 4400 reserves 1 Megabyte of DVMA space for VME32 peripheral devices.

If the sum of DVMA space requested by VME32 devices is greater than 1 Megabyte, some peripherals will not run correctly.

1 Network CoProcessor uses 192 Kilobytes of DVMA space

2 Network CoProcessors use 320 Kilobytes of DVMA space





5. SunOS for the SS600MP reserves 6 Megabytes of DVMA space for VME32 peripheral devices.

If the sum of DVMA space requested by VME32 devices is greater than 6 Megabytes, some peripherals will not run correctly. Each Network CoProcessor uses 416 Kilobytes of DVMA space.

Release Notes

1. Interphase Release 1.4 supports the Sun 4400 on SunOS 4.1.1.

2. SNC 1.0 supports the SS600MP on SunOS 4.1.2.

3. Patch 100639-01 supports the Sun 4400 on SunOS 4.1.2.

4. SNC 1.2 supports the Sun 4400 and SS600MP on SunOS 4.1.3.

5. The Sun Network CoProcessor is not supported in Solaris >=2.2.



References

1. NC300/NC400 Network CoProcessor Release 1.4 Installation Manual.

2. Sun Network CoProcessor 1.0 Installation Manual, 800-6881-10.


4. Sun Network CoProcessor 1.2 Product Note, 801-5133-10.

5. Writing Device Drivers, 800-3851-10.

Sun Network CoProcessor

Sun-4/470/490

SS630MP / SS670MP / SS690MP

Option 176



Power:

8.0 Amps @ +5Vdc

0.5 Amps

46.0 Watts

SNC 1.2 Jumper Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (6 von 8) [25.04.2002 16:16:35]


Address Jumpers and Address Bit Assignments

JUMPER JP1 JP2 JP3 JP4 JP5 JP6 JP7 JP8

ADDRESS BIT A31 A30 A29 A28 A27 A26 A25 A24

JUMPER JP9 JP10 JP11 JP12 JP13 JP14 JP15 JP16

ADDRESS BIT A23 A22 A21 A20 A19 A18 A17 A16

JUMPER JP17 JP18 JP19 JP20 JP21 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00520.htm (7 von 8) [25.04.2002 16:16:35]


ADDRESS BIT A15 A14 A13 A12 A11

Notes

1. SNC 1.2 requires Sun 4400 CPU 501-1381-09 or 501-1899-01.

2. SNC 1.2 requires IPI Firmware 525-1023-05, 525-1024-10, and 525-1025-10. This firmware is installed on ISP-80 IPI Controller 501-1539-10 and 501-1855-04.

3. SunOS for the Sun 4400 reserves 1 Megabyte of DVMA space for VME32 peripheral devices.

If the sum of DVMA space requested by VME32 devices is greater than 1 Megabyte, some peripherals will not run correctly.

1 Network CoProcessor uses 192 Kilobytes of DVMA space






4. SunOS for the SPARCserver 600MP reserves 6 Megabytes of DVMA space for VME32 peripheral devices. If the sum of DVMA space requested by VME32 devices is greater than 6

Megabytes, some peripherals will not run correctly. Each Network CoProcessor uses 416

Kilobytes of DVMA space.

Release Notes

1. SNC 1.0 supports the SS600MP on SunOS 4.1.2.

2. Patch 100639-01 supports the Sun 4400 on SunOS 4.1.2.

3. SNC 1.2 supports the Sun 4400 and SS600MP on SunOS 4.1.3.

4. The Sun Network CoProcessor is not supported in Solaris >=2.2.

References



3. Sun Network CoProcessor 1.2 Product Note, 801-5133-10.

4. Writing Device Drivers, 800-3851-10.



Sun4/I: Removable Media - Contents

Removable Media

1/4" Tape Controller

Emulex MT02

CD-ROM Drives

Sony CDU-8012 (SunCD)

1/4" Tape Drives

60MB

150MB

8 mm Tape Drives

2.3GB

1/2" Tape Drive

HP 88780 Front Load Tape Drive



Sun4/I: Removable Media - Emulex MT02

Emulex MT02

Sun-4/260/280/360/380

Options 511 / 514 / 516

370-1061 / 370-1235

KEY

LED 1

(Green)

LED 2

(Red)

0 = Off 0

1 = On 1

0

1

STATE

Power up reset clear

Power up self-test passed

LED 1. Blinking, MT02 operating normally.

LED 2, ON, Do NOT remove the cartridge.

Power

1.5 Amps @ +5Vdc

0.04 Amps @ +12Vdc

8.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b1.htm (1 von 3) [25.04.2002 16:16:47]



DIP SWITCH SWITCH SETTING

SW1 1

2

Off

Off

Bit 0

Bit 1

DESCRIPTION

5

6

5

6

3

4

7

8*

On Bit 2-SCSI device address 04

Off Not used

On

Off

On

On

Archive Drive (Scorpion)

Wangtek Drive (5000E)

Off Drive type

Off SCSI bus parity check

* The Sun386i Tape assembly, 370-1179, includes the MT02 Controller and the Tape Drive. SW1,

Switch 8, is ON for this application.

JUMPER SETTING

A-B*

C-D*

E-F*

In

Out

In

Out

DESCRIPTION

EPROM Memory size select

Hi/Lo write current (Archive Drive)

Hi/Lo write current (Wangtek Drive)

G-H

J-K **

L-M**

Out

Out

Out

* Jumpers A-B, C-D, and E-F are on the Emulex Rev. MW0210402 board. They are not on Rev.

MT0210403 and MT0210103 boards. SW1, Switch 5 and Switch 6, control drive selection on the

MT0210403 and MT0210203 boards.

**Jumpers J-K and L-M are in one of the locations shown on the board layout drawing.

Note

Terminators U5 and U46 must be installed for Sun-3/160 and Sun-3/180 Plus configurations.

Remove these terminators when the board is used with all other Sun-3 and Sun-4 Mass Storage

Subsystems.

References

1. Sun-3 Emulex MT02 Controller Configuration Procedures, 813-2011.

2. 60 Mbyte Streaming Tape Drive with SCSI Controller Configuration Procedures, 814-1019.

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b1.htm (2 von 3) [25.04.2002 16:16:47]



Sun4/I: Removable Media - Sony CDU-8012 (SunCD)

Sony CDU-8012 (SunCD)

Sun-4/330/370/390/470/490

SS600MP / SS1000 / SC2000

Options 558 / 559

370-1312 370-1347

Lt Grey Bezel Black Bezel

Front View

Rear View

In the Desktop SunCD Plus Pack, orient the Flex Cable as shown, and plug it into ID

SELECT 0 1 2.

In the Multi-Tape Backup Tray and SC2000, orient the Cable as shown, and plug it into ID

SELECT 0 1 2.

JUMPER SETTING DESCRIPTION

1, 2

Parity

In

In

SCSI ID 6

Enable parity http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b2.htm (1 von 2) [25.04.2002 16:16:51]

Sun4/I: Removable Media - Sony CDU-8012 (SunCD)

Power

0.5 Amps @ +5Vdc

0.5 Amps @ +12Vdc

8.5 Watts

Notes

1. The Sun CD-ROM requires 1.0 SunCD for SunOS 4.0.3c.

2. Use 370-1347-03 when mounted on-end in the SS630MP.



Sun4/I: Removable Media - 60MB 1/4" Tape Drive

60MB 1/4" Tape Drive

Sun-4/260/280/360/380

Options 515 / 514 / 516

370-1076 370-1103

Wangtech

5099EN24

Wangtech

5099EN24

Archive

5945C

Rear View of Wangtech Model 5099EN24

Rear View of Archive Model 5945C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b3.htm (1 von 3) [25.04.2002 16:17:05]


Power

1.0 Amps @ +5Vdc

1.9 Amps @ +12Vdc

27.8 Watts

Note

This tape drive is used with the Emulex MT02.

60MB 1/4" Tape Drive with Emulex MT02 Tape Controller

Sun-4/370

Options RR128 / RR129 / RREXP / RREXP-P7

370-1247 370-1179

Archive 5945S

Full-Height

Black Bezel

Archive 5945S

Full-Height

Lt Grey Bezel

Rear View

Emulex MT02 Tape Controller Switch Settings

DIP

SWITCH

SWITCH SETTING DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b3.htm (2 von 3) [25.04.2002 16:17:05]


SW1 1 & 2

3

1 & 3

2

6

7

4

5

8

8

Off

On

On

Off

Off

On

Off

Off

On

Off

SCSI target 4

SCSI target 4

SCSI target 5

SCSI target 5

Not used

Archive tape drive

Archive tape drive

Drive type

Parity check ON for 370-1179

Parity check OFF for 370-1247

Reference

60MB Streaming Tape Drive with SCSI Controller Configuration Procedures, 814-1019.




150MB 1/4" Tape Drive

Sun-4/330/370/390/470/490

SS630MP / SS670MP / SS690MP / SC2000

Options 539 / 565 / 660

370-1205 370-1206 370-1218 370-1246

Archive 2150S

Half-Height

Black Bezel

Archive 2150S

Full-Height

Black Bezel

Archive 2150S

Half-Height

Custom Bezel

Archive 2150S

Full-Height

Lt Grey Bezel

Rear View

Flex Cable

In the Desktop Tape Pack, remove the SCSI ID jumpers, orient the Flex Cable as shown, and plug it into the SCSI ID jumper block.

Address Select Switch Cable

In the External Storage Module, orient the Address Select Switch Cable as shown, and plug it into the SCSI ID jumper block.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b4.htm (1 von 2) [25.04.2002 16:17:13]


Power

0.7 Amps @ +5Vdc

1.5 Amps @ +12Vdc

21.5 Watts

Jumper Settings


RXD/TXD Out Serial Port

DIAG

Parity

CF2,CF1,CF 0

Out

Out*

In

Normal/Diag

Parity check

USAGE

Not used

Not used

Not used

Disconnect Transfer Size Size = 32K

JUMPER TARGET 2 TARGET 3 TARGET 4 TARGET 5

ID2

ID1

Out

In

Out

In

In

Out

In

Out

ID0

1st SCSI

2nd SCSI

Out st3 st7

In st2 st6

Out st0 st2, st4

In st1 st3, st5

* IN for 370-1246

Note

The Cartridge Tape part number is 370-1203-01.

Reference

150MB 1/4-Inch Cartridge Tape Drive Configuration Manual for the 56-Inch Data Center

Cabinet, 813-2076.



Sun4/I: Removable Media - 2.3GB 8 mm Tape Drive

2.3GB 8 mm Tape Drive

Sun-4/370/390/470/490

SS670MP / SS690MP

Options 566 / 802 / 804

370-1297 370-1405

Exabyte EXB-8200

Black Bezel

Exabyte EXB-8200

Lt Grey Bezel

Rear View

Jumper P2

SCSI ID (MSB) 1 2 (LSB) 3

4

5

In

In

Out

Out

Out

In

1

0

3

2

Out

Out

Out

Out

In

In

Out

Out

In

Out

In

Out

Address Select Switch Cable

In the Desktop Storage Module and External Storage Module, orient the Address Select

Switch Cable as shown, and plug it into P2.



Power

4.0 Amps @ +5Vdc

1.2 Amps @ +12Vdc

34.4 Watts

MX Card

Dip Switch U32

SWITCH SETTING

1

2

On

On

DESCRIPTION

Bypass memory test

Enable parity checking

5

6

3

4

7

8

On

Off

On

Off

Off

Off

Even byte disconnect

Report busy status

Variable block mode on power up

No disconnect during data transfer

Not used

P6 cartridge type

Manual Eject Switch

Notes

1. The 112 Meter Tape part number is 370-1298-01.

2. The Cleaning Kit part number is 370-1318-01.



3. ECO WO_01575 enabled Parity checking on the MX card. Parity checking is disabled on drives shipped prior to December 1991.

References

Sun 2.3-Gbyte 8mm Tape Drive Configuration Procedures for 56-Inch Data Center Cabinets,

813-2081.



Sun4/I: Removable Media - HP 88780 Front Load Tape Drive

HP 88780 Front Load Tape Drive

Options 680 / 682 / 683 / 684

Read/Write/Format Board

370-1276

Drive Controller Board

370-1277

Single Ended I/O Board

811-1241 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005b6.htm (1 von 3) [25.04.2002 16:17:31]


Data Buffer Board

370-1279

NVRAM Reset Procedure

1. Load a scratch tape.

2. Run TEST 150 to write a GCR ID to the scratch tape.

3. Run TEST 128 to store the NVRAM contents to the scratch tape.

4. Remove Power.

5. Install the new Data Buffer Board or new EPROMs.

6. Connect a jumper between locations GND and CLRNV.

7. Apply power. FAIL--0 is displayed when selftest is complete.

8. Remove Power.

9. Remove the jumper.

10. Apply Power.

11. Load the scratch tape.



12. Run TEST 129 to load NVRAM with the contents stored on tape.

13. Rewind to BOT.

14. Run TEST 99 to calibrate the read channel gain values.

Battery Notes

1. The battery part number is 150-1204-01 or 811-1232-01.

2. The battery is not replaceable on boards built after January 1990.

Reference

Sun Front-Load 1/2-Inch Tape Drive Field Service Manual,800-3447.



Sun4/I: SCSI Disk - Contents

SCSI Disk

Single Ended SCSI Disk Drives

CDC 94171-327/344 (327MB)

Micropolis 1588-15 (669MB)

Maxtor XT-8760S (669MB)

Seagate ST41600N (1.3GB)



Sun4/I: SCSI Disk - CDC 94171-327/344 (327MB)

CDC 94171-327/344 (327MB)

5 1/4" 3600 RPM Embedded SCSI

Sun-4/330/370/470

Options RREXP-P7 / RR129 / RR134

Options 526 / 527 / 530 / 539

555-1005 370-1153 370-1230 w Bracket w/o Bezel

77777107 w/o Bracket w/o Bezel

77777107

3 1/4" Height w/o Bracket w Bezel

77777126

3 1/4" Height

End View

Ground Select Jumper J3

Drive Select and Option Select Jumper J4

In the External Storage Module, orient the Address Select Switch Cable as shown, and plug it into J4.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005de.htm (1 von 4) [25.04.2002 16:17:48]


Terminator Power Source Select Jumper J5

Power

1.5 Amps @ +5Vdc

1.4 Amps @ +12Vdc

24.3 Watts

Jumper Settings

555-1005 and 370-1153 Only

J3

PIN SETTING

1-2 In

DESCRIPTION

AC + DC ground connected to signal ground

3-4 In AC + DC ground connected to chassis ground

J4

PIN SETTING DESCRIPTION

P In Parity enabled

J5

PIN SETTING

3-4 In

DESCRIPTION

Terminator power from DC connector

370-1230 Only

J3

PIN SETTING

1-2 Out

DESCRIPTION

AC + DC ground not connected to signal ground

3-4 Out AC + DC ground not connected to chassis ground

J4


P Out Parity enabled

J5

PIN SETTING

3-4 In

DESCRIPTION

Terminator power from DC connector http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005de.htm (2 von 4) [25.04.2002 16:17:48]


Address Jumper Settings

J4

PIN SETTING DESCRIPTION TARGET

1, 2, 4 Out Drive select Target 0

1

2

1, 2

In

In

In

Drive select

Drive select

Drive select

Target 1

Target 2

Target 3

Notes

1. Remove the terminators from the underside of the drive.

2. Terminate the Sun386i with external terminator 530-1381.

3. Sun-3/470, Sun-4/370, and Sun-4/470 systems with dual option trays are terminated internally on the 501-1493 Interface PCB. The left side tray must be installed to terminate the SCSI bus.

4. Sun-4/370 and Sun-4/470 systems with a single option tray are terminated externally with terminator 150-1346.

5. Terminate the External Storage Module with terminators 530-1381 or 150-1785.

6. Terminate the Sun-4/330 on the SCSI-Out PCB with three 220/330 terminators, 120-1608-01.

Format Utility Notes

1. The 94171-327 has fewer cylinders than the 94171-344.

2. The SunOS 4.x format utility fails if the 94171-327 is used with the standard format.dat entry on any system other than a Sun386i.

3. Use the following format.dat entry for the 94171-327 on SunOS 4.x.

disk_type = "CDC Wren IV 94171-327" \

: ctlr = SCSI : fmt_time = 4 : cache = 0x11: trks_zone = 9 \

: asect = 3 : ncyl = 1520 : acyl = 2 : pcyl = 1549 : nhead = 9 \

: nsect = 46 : rpm = 3600 : bpt = 20833

4. Solaris 2.x includes an entry for the 94171-327 in format.dat. Remove the comment symbol "#" to use the entry.

References

1. 386i Field Service Manual, 814-0002-10.

2. 327MB Embedded SCSI Configuration Procedures, 814-1015-01.

3. 5 1/4-Inch Disk Drive Installation in the 12-Slot Office Pedestal Manual, 813-1055-10.

4. Sun 327 Mbyte SCSI Disk Configuration Manual, 813-2048-03.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005de.htm (3 von 4) [25.04.2002 16:17:48]



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005de.htm (4 von 4) [25.04.2002 16:17:48]

Sun4/I: SCSI Disk - Micropolis 1588-15 (669MB)

Micropolis 1588-15 (669MB)

5 1/4" 3600 RPM Single Ended SCSI

Sun-4/330/370/470

Options 561 / 563 / 565 / 566

370-1319 370-1326 555-1151

FS0013-03-5

Black Bezel

Green LED

3 1/4" Height

FS0019-01-6

No Bezel

No LED

3 1/4" Height

FS0019-01-6

No Bezel

No LED w Bracket

Bottom View

Note

All other jumpers on this board are set by the manufacturer. Do NOT change these settings.

End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005df.htm (1 von 3) [25.04.2002 16:17:55]


Option Jumper Settings

JUMPER SETTING

W5

W4

Out

Out

DESCRIPTION

Spindle starts at power on

Enable parity detection

W1

W2

W11

W28

In

Out

Out

Drive provides internal terminator power

Out Frame ground not connected to logic ground

External Storage and Expansion Modules

JUMPER SETTING

W5

W4

Out

Out

DESCRIPTION



W1

W2

W11

W28

In

Out

Out

In

Drive provides internal terminator power

Frame ground connected to logic ground http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005df.htm (2 von 3) [25.04.2002 16:17:55]


Address Jumper Settings

J2 Multi-function Connector


0,1, 2 Out

0 In

Target 0

Target 1

1

0,1

In

In

Target 2

Target 3

References

1. 5-1/4" SCSI Disk Drive Installation and Configuration for Sun Office Pedestals, 813-2048-11.

2. Revised Removal/Replacement Procedures for Sun ESM and EEM Storage Units, 814-3044-01.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005df.htm (3 von 3) [25.04.2002 16:17:55]

Sun4/I: SCSI Disk - Maxtor XT-8760S (669MB)

Maxtor XT-8760S (669MB)


Sun-4/330/370/470

Options 561 / 563 / 565 / 566

370-1319 370-1326 555-1151

1098618-B

Black Bezel

Green LED

3 1/4" Height

1098778-B

No Bezel

No LED

3 1/4" Height

FS0019-01- 6

No Bezel

No LED w Bracket

Bottom View

Note

All other jumpers on this board are set by the manufacturer. Do NOT change these settings.

End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e0.htm (1 von 3) [25.04.2002 16:18:00]


Address Description

The address is set on the J2 Adapter installed in the J2 Auxiliary connector, the Address Select switch on the External Storage Module, or on Jumpers JP35, JP36, and JP37. Set the address at only one location.

J2 Adapter Circuitry

External Storage Module

Orient Pin-1 of Address Select Switch Cable 530-1659 with ID4 on the J2 Adapter.



J2 Auxiliary Connector with Adapter 811-1682-01


1,2,4 Out Target 0

1

2

1,2

In

In

In

Target 1

Target 2

Target 3

JP35, JP36, and JP37


JP35, JP36, JP37 Out Target 0

JP35

JP36

JP35, JP36

In

In

In

Target 1

Target 2

Target 3

Option Jumper Settings

JUMPER SETTING

JP14 In

DESCRIPTION


JP38

JP40

Out

In

No motor delay at power on


JP41

JP34

In Drive provides internal terminator power

Out Terminator power option

Notes

1. Drive address selection cannot be set on Auxiliary Connector J2 unless the adapter is installed.

2. The J2 Adapter must be installed in order for the ID Select Switch on the External Storage

Module to function

3. The Maxtor drive does not fit into the lower drive position of External Storage Modules manufactured prior to October 1990. Remove the vertical stop block with 10-Inch End Cutter

250-1074-01.

References

1. 5-1/4" SCSI Disk Drive Installation and Configuration for Sun Office Pedestals, 813-2048-11.

2. Revised Removal/Replacement Procedures for Sun ESM and EEM Storage Units, 814-3044-01.



Sun4/I: SCSI Disk - Seagate ST41600N (1.3GB)

Seagate ST41600N (1.3GB)

976002-012 Elite-1 Family


Sun-4/470 / SS630MP / SS670MP

Option 571

370-1377

3 1/4" Height

Top View

End View http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e1.htm (1 von 3) [25.04.2002 16:18:16]


In the Desktop Storage Module, orient Pin-1 of the Address Select Switch Cable with ID2 on J5. Remove all jumpers from J4A.

Power

2.4 Amps @ +5Vdc

2.1 Amps @ +12Vdc

37.2 Watts

Jumper Settings

Jumper J4A Jumper J5 Jumper J4B

J4A


ID0,ID1,ID 2 Out Drive ID select, Target 0

ID0

ID1

In

In

Drive ID select, Target 1


ID0,ID1

WRT

SLV

In

Out

Out


Write enabled

Spindle sync master

J5*


ID0,ID1,ID 2 Out Drive ID select, Target 0

ID0

ID1

ID0,ID1

In

In

In




* Factory configurations do not use shunts at Jumper J5.

J4B

JUMPER SETTING

SDO In

DESCRIPTION

Spinup Delay = 10sec x Target ID http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005e1.htm (2 von 3) [25.04.2002 16:18:16]


SCO

SCP

SWP

Out Spinup according to SD0 setting

Out Parity enabled

In Sweep cycle enabled

J01

JUMPER SETTING

1-2

2-4

DESCRIPTION

The drive supplies TERMPWR to its own terminator.

It does not supply TERMPWR to the SCSI bus.

The drive supplies no TERMPWR.

The initiator supplies TERMPWR to the bus.

1-3

2-4

In

In

The drive supplies TERMPWR for the external terminator at the end of the daisy chain. This option is recommended only for the last drive on a daisy chain.

Notes


2. SunOS 4.1.1 Sun-4c requires the 1.3GB Disk Drive Enhancement (esp.o, sd.o, and format.dat).

3. SunOS 4.1.1 Rev B Sun-4c requires the 1.3GB Disk Drive Enhancement (esp.o and sd.o).

4. SunOS 4.1.1 Sun-4 requires the 1.3GB Disk Drive Enhancement (format.dat).

5. Jumper J4A uses 2 mm shunts. Jumper J5 can be configured using 2.54 mm shunt 130-0272.

The Target ID is the Boolean OR of J4A and J5. Do NOT install shunts in both locations. Do

NOT install shunts at J4A when the address select switch cable is installed.

6. The 1.3GB Disk Drive is not supported inside Sun 12-Slot Office Pedestals that use SCSI

Interface PCBs 501-1493 and 501-1496.

7. The 1.3GB Disk Drive is not supported inside SCSI Peripheral Trays that use SCSI Interface

PCB 501-1496.

References

1. Desktop Storage Module Service Manual, 800-6219-10.

2. Desktop Storage Module Service Manual, 800-7236-10.

3. Sun SCSI Expansion Pedestal Service Manual, 800-6402-11.

4. Sun SCSI Expansion Pedestal Service Manual, 800-7285-10.

5. 12-Slot Office Pedestal with Single Peripheral Tray, 800-6497-10.



Sun4/I: SCSI - Contents

SCSI

ESDI

Emulex MD21

VMEbus


Blank SCSI Adapter Assembly


Sun-3/E SCSI/Ethernet



Sun4/I: SCSI - Emulex MD21

Emulex MD21

Sun-4/260

Options 504 / 505 / 507 / 509 / 510 / 514 / 516

370-0552 / 370-1236

Power

1.6 Amps @ +5Vdc

8.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005cd.htm (1 von 2) [25.04.2002 16:18:22]

Sun4/I: SCSI - Emulex MD21


DIP

SWITCH SETTING

1

2

3

Off*

Off

Off

DESCRIPTION

SCSI BUS ADDRESS/TARGET

Bit 0-7

6

7

4

5

8

Off

Off

Off

Off

Off

Not used

512 byte/sector

Power on spin-up

Soft errors reported

Parity disabled

* For DeskTop Expansion Shoebox, Dip Switch 1 is ON for Target 1.

JUMPER SETTING

E, F* Out

DESCRIPTION

SCSI bus termination power option

* Jumpers E and F are not on Emulex Rev MD2110103.

Note

Install termination resistor packs on the last Tape/Disk Controller on the SCSI bus.

Reference

ESDI Disk Controller Configuration Procedures, 813-2022.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005cd.htm (2 von 2) [25.04.2002 16:18:22]

Sun4/I: SCSI - Sun-2 SCSI Host Adapter

Sun-2 SCSI Host Adapter

Sun-4/260/280

501-1045

Power

2.8 Amps @ +5Vdc

14.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (1 von 5) [25.04.2002 16:18:37]




J500 1-2

3-4

5-6

7-8

Out

Out

Out

In

Bus Grant 0 In

Bus Grant 1 In

Bus Grant 2 In

Bus Grant 3 In

J501 1-2

3-4

5-6

7-8

J502 1-2

3-4

5-6

7-8

J600 and

J601

1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

In

Out

Out

In

Out

Out

Out

In

Out

Out

In

Out

Out

Out

Out

Out

Bus Request 0

Bus Request 1

Bus Request 2

Bus Request 3

Bus Grant 0 In

Bus Grant 1 In

Bus Grant 2 In

Bus Grant 3 In

Interrupt Level 0

Interrupt Level 1

Interrupt Level 2

Interrupt Level 3

Interrupt Level 4

Interrupt Level 5

Interrupt Level 6

Interrupt Level 7


U702* 1-4

5-8

On/Off

On

Not connected

A12 - A15

U704* 1-5

6

7-8

On

Off

On

A16 - A20

A21

A22 - A23

* U0702 and U0704 set the address to 0x200000 for the first SCSI

Sun-2 SCSI Host Adapter Assembly

Sun-4/280

501-1138 without P2A and P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (2 von 5) [25.04.2002 16:18:37]


Power

2.7 Amps @ +5Vdc

13.5 Watts


Sun-4/260

501-1149 with P2A and P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (3 von 5) [25.04.2002 16:18:37]


Power

2.7 Amps @ +5Vdc

13.5 Watts


Sun-4/280

501-1167 with P2A and P2C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (4 von 5) [25.04.2002 16:18:37]


Power

2.7 Amps @ +5Vdc

13.5 Watts


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005ce.htm (5 von 5) [25.04.2002 16:18:37]

Sun4/I: SCSI - Blank SCSI Adapter Assembly

Blank SCSI Adapter Assembly

Sun-4/360

501-1666 with P2A and P2C


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005cf.htm [25.04.2002 16:18:43]


Sun-3 SCSI Host Adapter

Sun-4/260/280/330/370/390/490

501-1236

Power

4.8 Amps @ +5Vdc

24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (1 von 5) [25.04.2002 16:18:58]


Switch Settings

DIP

SWITCH


SW1*

U409

7

8

5

6

3

4

1

2

On

On

Off

On

On

On

On

On

Address A23

Address A22

Address A21

Address A20

Address A19

Address A18

Address A17

Address A16

SW2*

U408

7

8

5

6

3

4

1

2

On

On**

On

On

On

On/Off

On/Off

On/Off

Address A23

Address A22

Address A21

Address A20

Address A19

Not Connected

Not Connected

Not Connected

*SW1 and SW2 set the address to 0X200000 for the first SCSI.

**SW2, Switch 2, OFF, sets the address to 0x204000 for the second SCSI.

Notes

1. Do NOT use the original release of this board, 501-1120-xx.

2. The Sun-3/1xx CPU must be 501-1074-22, 501-1094-22, 501-1134-06, 501-1163-09,

501-1164-09, or greater.

3. The Sun-3 SCSI must be >=501-1236-02, >=501-1170-06, or >=501-1217-03 when used with a

SunLink Channel Adapter.

4. Set the base address as a second SCSI in Sun-4300 systems. The first SCSI Host Adapter is on the Sun 4300 CPU.

5. The Sun-3 SCSI must be >=501-1236-08 or >=501-1217-09 when used with the Sun-4400

CPU.

6. SCSI TERMPWR is provided on boards >=501-1236-08 and >=501-1217-09.

References

1. Sun-3 SCSI Configuration Procedures, 813-2007-01.

2. Sun-3 SCSI Host Adapter Configuration Procedures, 813-2077-11 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (2 von 5) [25.04.2002 16:18:58]



Sun-4/260

501-1170 with P2A and P2C

Power

4.8 Amps @ +5Vdc

24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (3 von 5) [25.04.2002 16:18:58]



Sun-4/280/330/370/390/470/490

501-1217 without P2A and P2C

Power

4.8 Amps @ +5Vdc

24.0 Watts

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (4 von 5) [25.04.2002 16:18:58]


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d0.htm (5 von 5) [25.04.2002 16:18:58]

Sun4/I: SCSI - Sun-3/E SCSI/Ethernet

Sun-3/E SCSI/Ethernet

501-8027 501-1584

9U Assembly

Ethernet Only

Power

4.1 Amps @ +5Vdc

20.5 Watts

Notes

1. Board revision 501-8027-06 or 501-1584-01 is required for use in any SPARC CPU based system.

2. The fuse is not replaceable.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d1.htm (1 von 3) [25.04.2002 16:19:05]


3. When used with the Sun-4400 CPU, 501-1381, the board revision must be >=501-8027-07 or the assembly must be >=501-1584-02.

4. SCSI TERMPWR is provided on boards >=501-8027-07.

Reference

Sun SunNet Ethernet/VME Controller Configuration Procedures , 813-2082-10.

501-8027 Switch and Jumper Settings


SW0601 1-7 On Enable Thin Ethernet

1-7 Off Enable Ethernet*


SW0201 1 Off 24/32-bit addressing

2

3

Off/On

*

N/C

A18 address decode

6

7

4

5

8

*

*

Off

On

On

A19 address decode

A20 address decode

A21 address decode

A22 address decode

A23 address decode

* DIP Switch SW0201 settings for ie2, ie3, and ie4

SW0201 SWITCH 3 SWITCH 4 SWITCH 5 ADDRESS

1st Board On On Off 31ff02

2nd Board

3rd Board

Off

Off

On

Off

Off

On

35ff02

2dff02


SW0202 1

2

On

On

A24 address decode

A25 address decode

5

6

3

4

7

On

On

On

On

On

A26 address decode

A27 address decode

A28 address decode

A29 address decode

A30 address decode


J0201 1-2 In Clock enable

J0601 1-2

J0601 1-2

J0602 1-2

In

Out

Out

Level 1 Ethernet

Level 2 Ethernet

VCC to Pin-7 disabled http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d1.htm (2 von 3) [25.04.2002 16:19:05]


Note: The SCSI base address under SunOS 3.5 diag is 31000.


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd005d1.htm (3 von 3) [25.04.2002 16:19:05]

Sun4/I: IPI - Contents

IPI

IPI Disk Controller

ISP-80 / IPI-2

IPI Disk Drives

Seagate 97229-11G (911MB)

Seagate 97209-12G (1.2GB)

Seagate 975002-005 (1.3GB)


Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004ad.htm [25.04.2002 16:19:08]

Sun4/I: IPI - ISP-80 / IPI-2

ISP-80 / IPI-2

Sun-4/390/470/490

SS670MP / SS690MP

Options 408 / 418

501-1539 / 501-1855

Power:

11.8 Amps @ +5Vdc



Base Address Select Switches

DIP SWITCH 1 2 3 4 5 6 7 8

SW1603 AM0 AM1 A10 A11 A12 A13 A14 A15

SW1602 A16 A17 A18 A19 A20 A21 A22 A23

SW1601 A24 A25 A26 A27 A28 A29 A30 A31


Note

Dip Switches 3, 4, and 5 of SW1603, select bits A10, A11, and A12 of the controller base address. These are the only switches changed to configure multiple controllers.



Jumper JM2


1-2 In Enable UART clock

ISP-80 / IPI-2

A minimum ISP-80 firmware level is required to support these products.

PRODUCT U0501 U0502 U0503

911MB Disk 525-1023-05 525-1024-07 525-1025-07

Prestoserve 525-1023-05 525-1024-08 525-1025-08

1.3GB Disk 525-1023-05 525-1024-08 525-1025-08

Dual Port 525-1023-05 525-1024-09 525-1025-09

SNC 1.2

525-1023-05 525-1024-10 525-1025-10

These ISP-80 part numbers have the firmware level required for the products listed.

PRODUCT ISP-80 ISP-80

4400 CPU 501-1539-04 501-1855-01

911MB Disk 501-1539-05 501-1855-01

Prestoserve 501-1539-08 501-1855-02

1.3GB Disk 501-1539-09 501-1855-03

Dual Port 501-1539-09 501-1855-03

SNC 1.2

501-1539-10 501-1855-04

DP Bug fixes 501-1539-10 501-1855-04

Notes

1. Upgrade lower revision ISP-80 boards with firmware Option X2080A.

2. Do not install firmware Option X2080A on ISP-80 501-1539-06. An unused trace may cause a system reset. Replace the ISP-80.

3. Booting from an alternate controller (1, 2, 3, or 4) is not supported on the 4300 and 4400 systems. Refer to Bug ID 1027710.

References

1. ISP-80 Disk Controller Configuration Procedures, 813-2065-10.

2. ISP-80 Disk Controller Installation and Configuration Procedures for the Sun 12-Slot Office

Pedestal, 813-1103-10.

3. ISP-80 Disk Controller Installation and Configuration Procedures, 813-1050-11.

4. ISP-80 Disk Controller PROM Upgrade Manual, 813-6089-11.




Sun4/I: IPI - Seagate 97229-11G (911MB)

Seagate 97229-11G (911MB)

Equipment Number PA8Y2

8" 3600 RPM IPI-2 6MB/Sec

Options 716 / 717 / 719 / 720 / 741L / 742L / 743L /

744L / 745L

Operator Panel

370-1355 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057a.htm (1 von 4) [25.04.2002 16:19:28]


Note

Each drive power-on sequence is delayed for a time equal to five seconds times its address. For example, if the address is 3, the drive starts after a 15-second delay.

Disk Enclosure

370-1351 370-1352 540-2005 540-2008

Rackmount Disk w/o Power Supply w/o Tray

Pedestal Disk w/o Bracket

Rackmount Disk w Power Supply w Tray

Pedestal Disk w Bracket

Control Board Dip Switch Settings

Dip Switch 1, Switches 1,2,3,4

DRIVE SWITCH 4 SWITCH 3 SWITCH 2 SWITCH 1

0

1

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Open

4

5

2

3

6

7

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Open

Open

Open

Open

Open

Open

Closed

Closed

Open

Open

Closed

Open

Closed

Open

Closed

Open

Dip Switch 1, Switches 5 and 6

SWITCH DESCRIPTION

5

6

Not used

Open = Write protected

Closed = Write enabled http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057a.htm (2 von 4) [25.04.2002 16:19:28]


I/O Board Rear View

Power Connector

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

+24

RTN

+24 +24 +24 +24

RTN

+24

RTN

N/C PWR

OK

-12 -5 -5 GND GND +5 +5

Dip Switch 1 Settings

SWITCH SETTING

3

4

1

2

Open

Closed

Open

Closed

DESCRIPTION

Drive starts when DC Power is applied

Disable Port B

Enable Port A

Disable internal diagnostics http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057a.htm (3 von 4) [25.04.2002 16:19:28]


7

8

5

6

9

Open

Closed

Open

Closed

Open

1D 3

1D 2

1D 1

1D 0

ID Microcode. Do Not Change

"

"

"

Slave/Master spindle sync-slave

Notes

1. The 911MB Disk requires minimum ISP-80 firmware 525-1023-05, 525-1024-07, and

525-1025-07.

2. ISP-80 501-1539-05 and 501-1855-01 contain the minimum firmware required by the 911MB

Disk.

3. Upgrade lower revision ISP-80 Controller boards with Option X2080A.

4. Use terminator 370-1220-01 on the Port A/B Out connector.

5. Disable an unused port with the Port Enable/Disable switch.

6. Do not install a terminator on an unused port.

7. There are cooling vents on the cover of 911MB Drive 370-1351. Do not install this drive in the

Sun Expansion Pedestal.

8. There are no cooling vents on the cover of 911MB Drive 370-1352. Do not install this drive in the Sun 56" Rack.

9. Power Supply 300-1052 does not support the 911MB Drive.

10. Use Power Supply 300-1075 in the Sun Expansion Pedestal.

References

1. IPI8-1000/2HP Disk Drive Configuration and Installation Procedures for the Sun Expansion

Pedestal, 813-5377-11.

2. PI8-1000 and IPI8-1000/2HP Disk Drive Configuration and Installation Procedures for the

Sun 56-inch Cabinets, 813-1109-10.



Sun4/I: IPI - Seagate 97209-12G (1.2GB)

Seagate 97209-12G (1.2GB)

Equipment Number PA8R2

8" 3600 RPM IPI-2 3MB/Sec

Options 706 / 707 / 709 / 710 / 741A / 742A / 743A /

744A / 745A

Operator Panel

370-1221 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057b.htm (1 von 4) [25.04.2002 16:19:36]


Note

Each drive power on sequence is delayed for a time equal to five seconds times its address. For example, if the address is 3, the drive starts after a 15-second delay.

1.2GB Disk Enclosure

370-1187 370-1314 540-1770 540-1926

Rackmount Disk w/o Power Supply w/o Tray

Pedestal Disk w/o Bracket

Rackmount Disk w Power Supply w Tray

Pedestal Disk w Bracket

Control Board Dip Switch Settings

Dip Switch 1, Switches 1,2,3,4

DRIVE SWITCH 4 SWITCH 3 SWITCH 2 SWITCH 1

0

1

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Open

4

5

2

3

6

7

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Open

Open

Open

Open

Open

Open

Closed

Closed

Open

Open

Closed

Open

Closed

Open

Closed

Open

Dip Switch 1, Switches 5 and 6

SWITCH DESCRIPTION

5

6

Not used

Open = Write protected

Closed = Write enabled

Control Board Types http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057b.htm (2 von 4) [25.04.2002 16:19:36]


I/O Board Rear View

Power Connector

15 14 13 12 11 10 9 8 7 6 5 4 3 2 1

+24

RTN

+24 +24 +24 +24

RTN

+24

RTN

N/C PWR

OK

-12 -5 -5 GND GND +5 +5

Dip Switch 1 Settings

SWITCH SETTING DESCRIPTION http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057b.htm (3 von 4) [25.04.2002 16:19:36]


7

8

5

6

9

3

4

1

2

Open

Closed

Open

Closed

Open

Closed

Open

Closed

Open

Drive starts when DC Power is applied

Disable Port B

Enable Port A

Disable internal diagnostics

1D 3

1D 2

1D 1

1D 0

ID Microcode. Do Not Change

"

"

"

Slave/Master spindle sync-slave

Notes

1. Use terminator 370-1220-01 on the Port A/B Out connector.

2. Disable an unused port with the Port Enable/Disable switch.

3. Do not install a terminator on an unused port.

4. Switch 9 is on I/O board LYBX. It is not on I/O board BXDX.

5. Do not install Disk Drive 370-1187 in the Sun Expansion Pedestal if there are cooling vents on the top cover.

6. Power Supply 300-1052-02 does not support 1.2GB Disk Drives.

7. Power Supply 300-1052-03 supports two 1.2GB Disk Drives. Power must be distributed between the two 410 Watt modules.

8. Power Supply 300-1052-04 supports four 1.2GB Disk Drives.

9. Power Supply 300-1052-05 does not support 1.2GB Disk Drives.

10. Use Power Supply 300-1075 in the Sun Expansion Pedestal.

References

1. IPI8-1000/2HP Disk Drive Configuration and Installation Procedures

or the Sun Expansion Pedestal, 813-5377-11.

2. IPI8-1000 and IPI8-1000/2HP Disk Drive Configuration and

Installation Procedures for the Sun 56-inch Cabinets, 813-1109-10.



Sun4/I: IPI - Seagate 975002-005 (1.3GB)

Seagate 975002-005 (1.3GB)

Equipment Number PA4F2/ST41201K

5 1/4" / 5400 RPM / IPI-2 / 3.25-4.5MB/Sec

Sun-4/490 / SS690MP

Options 726 / 727 / 728

370-1378 540-2127 w/o Bracket

3 1/2" Height

FRU w Bracket

Servo Board

I/O Board and I/O Transceiver Board http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057c.htm (1 von 3) [25.04.2002 16:19:43]


Power:

2.7 Amps @ +5Vdc

2.0 Amps @ +12Vdc

37.5 Watts

Servo Board Switch Settings http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0057c.htm (2 von 3) [25.04.2002 16:19:43]


I/O Transceiver Board Switch Settings

Notes


2. SunOS 4.1.1 and SunOS 4.1.1 Rev B require the 1.3GB Disk Drive Enhancement (format.dat).

3. The 1.3GB Disk requires minimum ISP-80 firmware, 525-1023-05, 525-1024-09, and

525-1025-09.

4. ISP-80 501-1539-09 and 501-1855-03 contain the minimum firmware required by the 1.3GB

Disk.

5. Upgrade lower revision ISP-80 Controller boards with Option X2080A.

6. IPI Cables without toroids, 530-1487 and 530-1518, can be used with the Sun-4/490.

Reference

Sun 1.3GB IPI Tray and Disk Drive Installation/Service Manual, 800-6676.



Sun4/I: Graphics - Contents

Graphics

VMEbus

GP Graphics Processor

GP+ Graphics Processor Plus

GP Graphics Buffer

CG3 Sun 3160 Color Frame Buffer


GP2 Graphics Processor

CG9 24-bit Color Frame Buffer


VX and MVX Visualization Accelerators

Sun-3/E Monochrome Frame Buffer

Sun-3/E Color Frame Buffer

P4 Bus

MG3 ECL Monochrome Frame Buffer

MG4 Analog/ECL Frame Buffer



CG8 24-bit Color Frame Buffer

SBus

MG1 ECL Monochrome Frame Buffer

MG2 Analog Frame Buffer



Comments and Suggestions http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004aa.htm [25.04.2002 16:19:48]

Sun4/I: Graphics - GP Graphics Processor

GP Graphics Processor

Sun-4/150/260/280/330/350/360/370/380

501-1055

UNIX ID: /dev/gpone0a-d

Power

GP

16.4 Amps @ +5Vdc

82.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054d.htm (1 von 3) [25.04.2002 16:19:57]



J12

J13

J14

J15

J8

J9

J10

J11

JUMPER

J1

J2

J3

SETTING

Out

In

In

DESCRIPTION

GP board ID bit 3

GP board ID bit 4

GP board ID bit 2

J4

J5

Out

Out

GP board ID bit 5

GP board ID bit 1

J6 Out GP board ID bit 6

J7 In if GB is installed GP board ID bit 0

J16

J17

J18

Out

Out*

Out*

Out*

Out*

Out*

In

Out

Out

Out*

Out

GP board ID bit 7

GND test point

GND test point

PP halt test point

VP halt test point

Manual reset test point

Main clock connect

VP free-running CLK test point

PP free-running CLK test point

GND test point

GND test point

*Hardwired


UR11-1 On VME address bit 17

UR11-2

UR11-3

Off

On

VME address bit 16

VME address bit 23

UR11-4

UR11-5

UR11-6

UR11-7

UR11-8

On

Off

On

On

On

VME address bit 22

VME address bit 21

VME address bit 20

VME address bit 19

VME address bit 18

Notes

1. The Sun-2/160 Power Supply requires RC Network 540-1300-01.

2. The default base address is 0x210000.

Reference

Hardware Installation Manual for the Sun-2/130 and Sun-2/160, 800-1144.





Sun4/I: Graphics - GP+ Graphics Processor Plus

GP+ Graphics Processor Plus

Sun-4/150/260/280/330/350/360/370/380

501-1139

UNIX ID: /dev/gpone0a-d

Power

GP+

14.6 Amps @ +5Vdc

73.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054e.htm (1 von 3) [25.04.2002 16:20:02]



J12

J13

J14

J15

J8

J9

J10

J11

JUMPER

J1

J2

J3

SETTING

Out

In

In

DESCRIPTION

GP board ID bit 3

GP board ID bit 4

GP board ID bit 2

J4

J5

Out

Out

GP board ID bit 5

GP board ID bit 1

J6 Out GP board ID bit 6

J7 In if GB is installed GP board ID bit 0

J16

J17

J18

Out

Out*

Out*

Out*

Out*

Out*

In

Out

Out

Out*

Out

GP board ID bit 7

Ground test point

Ground test point

PP halt test point

VP halt test point


Main clock connect

VP free-running CLK test point

PP free-running CLK test point

Ground test point

Ground test point

*Hardwired


UR11-1 On VME address bit 17

UR11-2

UR11-3

Off

On

VME address bit 16

VME address bit 23

UR11-4

UR11-5

UR11-6

UR11-7

UR11-8

On

Off

On

On

On

VME address bit 22

VME address bit 21

VME address bit 20

VME address bit 19

VME address bit 18

Notes

1. The Sun-2/160 Power Supply requires RC Network 540-1300-01.

2. The default base address is 0x210000.

Reference

Graphics Processor Plus Configuration Procedures, 813-2023.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054e.htm (2 von 3) [25.04.2002 16:20:02]




Sun4/I: Graphics - GP Graphics Buffer

GP Graphics Buffer

Sun-4/150/260/280/360/370/380

501-1058

Power

2.1 Amps @ +5Vdc

10.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0054f.htm (1 von 2) [25.04.2002 16:20:08]

Sun4/I: Graphics - GP Graphics Buffer


JUMPER SETTING

J1 Out

DESCRIPTION

Ground test point

J2

J3

Out

Out

Ground test point


J4 (2-3)

J5

J6

J7

In

In/Out*

In/Out*

In/Out*

Graphics buffer = 2MB

Refresh interval test point bit 0



J8

J9

J10

In/Out* Refresh interval test point bit 2

Out Ground test point

Out Ground test point

*Hardwired

Notes

The Sun-2/160 Power Supply requires RC Network, 540-1300-01,

(FCO 160-0002, Doc 807-0029).

Reference




Sun4/I: Graphics - CG3 Sun 3160 Color Frame Buffer

CG3 Sun 3160 Color Frame Buffer

Sun-4/110/150/260/280/310/330/350/360/370/380

501-1116 501-1089 501-1319

Single Buffered Double Buffered* 1Kx1K

*Double buffering requires SunOS 3.5 (Sun-3) or SunOS 4.0 (Sun-4).

UNIX ID: /dev/cgtwo0

Power

501-1116 501-1319 and 501-1089

8.2 Amps @ +5Vdc 8.3 Amps@ +5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00550.htm (1 von 3) [25.04.2002 16:20:14]


2.9 Amps @ -5Vdc 3.1 Amps @ -5Vdc

0.1 Amps @ +12Vdc 0.1 A mps @ +12Vdc

0.2 Amps @ -12Vdc 0.2 Amps @ -12Vcd

59.0 Watts 61.2 Watts



J100 All -

DESCRIPTION

Factory set

J101

J102

All

1-2

-

In

Factory set

J300

J301

1-16

1-2

3-4

3-4

3-4

9-10

11-12

13-14

15-16

Out

Out

In/Out*

Out

Out

In/Out*

Out

In/Out*

In/Out*

Default address = 0x400000








J302

J303

J400

1-2

1-2

3-4

1-2

3-4

1-2/J8

1-2/J8

3-4/J9

5-6/J10

7-8/J11

9-10/J12

11-12/J13

Out

In

In/Out*

In/Out*

Out

Out

Out

Out

Out

Out

Out

Out

Resolution = 1152 x 900

Resolution = 1014 x 1024

J600

J601

11-12/J13

13-14/J14

15-16/J15

All

All

In

Out

Out

-

-

VME port and GP port

VME port fast read

CG3 <=501-1116-05

VME port fast read

CG3 >=501-1116-06

Reserved

Reserved

Factory set

Factory set

*Hardwired http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00550.htm (2 von 3) [25.04.2002 16:20:14]


References

1. Installation Notes for the GP2 and CG5 Boards, 800-2330.

2. Sun-3 Color Board Configuration Procedures, 813-2030.



Sun4/I: Graphics - CG5 Color Frame Buffer

CG5 Color Frame Buffer

Sun-4/110/150/260/280

Sun-4/310/330/350/360/370/380/380

Sun-4/470/490

501-1267


Power

8.8 Amps @ +5Vdc

3.2 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00551.htm (1 von 3) [25.04.2002 16:20:21]


0.2 Amps @ +12Vdc

0.1 Amps @ -12Vdc

64.2 Watts

Switch Settings

SWITCH SETTING

SW300-1

SW300-2

SW300-3

SW300-4

SW300-5

SW300-6

SW300-7

SW300-8

Off

Off

Off

Off

Off

Off

Off

Off

DESCRIPTION

A24 address decode

A25 address decode

A26 address decode

A27 address decode

A28 address decode

A29 address decode

A30 address decode

A31 address decode

SW301-1

SW301-2

SW301-3

SW301-4

SW301-5

SW301-6

SW301-7

SW301-8

SW302-1

SW302-2

SW302-3

SW302-4

SW302-5

SW302-6

SW302-7

SW302-8

SW400-1

SW400-2

SW400-3

SW400-4

SW400-5

SW400-6

SW400-7

SW400-8

Off

On

Off

Off

On

Off

On

On

On

Off

Off

On

N/C

N/C

N/C

N/C

Off

Off

Off

Off

On

On

Off

Off

A22 address decode

A23 address decode

AM4 decode

AM5 decode

2MB H/L decode

2/4MB, A21 decode

2/4MB, X.A21 decode

2/4MB, X.A21

Control space 2/4MB decode

Control space 2/4MB decode

24/32 bit address decode (24 bit)

24/32 bit address decode (24 bit)

Not used

Not used

Not used

Not used

Status bit 08 (resolution)




Status bit 12 (extra registers)

Status bit 13 (fast RD)

Status bit 14 (RFU)

Status bit 15 (RFU) http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00551.htm (2 von 3) [25.04.2002 16:20:21]


SW3300-1

SW3300-2

SW3300-3

SW3300-4

SW3300-5

SW3300-5

SW3300-6

SW3300-7

SW3300-8

On

Off

Off

Off

Off

On

Off

Off

Off

Selects board 0

Selects board 1

Selects board 2

Selects board 3

P2 Bus not enabled

P2 Bus enabled - required if GP2 is installed

No connection

No connection

No connection

Jumper Settings


J600 1-2

3-4

5-6

7-8

J601 1-2

3-4

5-6

7-8

In

Out

Out

Out

In

Out

Out

In

DESCRIPTION

V reset

External vertical blank output to ground

External display buffer A output to

No connection

Green sync

Green sync

Sync

Sync

Notes

1. The Sun 4300 CPU must be 501-1316-03 for use with CG5.

2. The CG5 must be 501-1267-05 for use with the 501-1539 ISP-80 Disk Controller.

References


2. Configuration Procedures for the GP2 and CG5 Boards, 813-2059.



Sun4/I: Graphics - GP2 Graphics Processor

GP2 Graphics Processor

Sun-3/150/160/180/260/280/460/470/480

Sun-4/150/260/280/330/350/360/370/380

Sun-4/390/470/490

501-1268

UNIX ID: /dev/gpone0a-d http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00552.htm (1 von 2) [25.04.2002 16:20:27]

Sun4/I: Graphics - GP2 Graphics Processor

Power

12.1 Amps @ +5Vdc

60.5 Watts

Switch Settings


U1601-1

U1601-2

U1601-3

U1601-4

U1601-5

U1601-6

U1601-7

U1601-8

Off

On

On

Off

On

On

On/Off

On/Off

A18 address decode

A19 address decode

A20 address decode

A21 address decode

A22 address decode

A23 address decode

Not used

Not used

Notes

1. The GP2 is used with the CG5 or CG9. Unbundled software is required for SunOS 3.5, 3.5.1,

3.5.2, Sys4-3.2, and Sys43.2.1. Unbundled software is not required for SunOS 4.0.

2. The GP2 must be 501-1268-07 for use with CG9.

3. The CG9 is not supported under OpenWindows Versions 2 or 3.

References


2. Configuration Procedures for the GP2 and CG5 Boards, 813-2059.



Sun4/I: Graphics - CG9 24-bit Color Frame Buffer

CG9 24-bit Color Frame Buffer

Sun-3/260/460/470/480

Sun-4/150/260/280/330/350/360/370/380/390/470/490

501-1434

UNIX ID: /dev/cgnine0

Power

14.6 Amps @ +5Vdc



Notes

1. The GP2 must be 501-1268-07 when used with CG9.

2. The CG9 is not supported with the GP or GP+.

3. CG9 must be >=501-1434-04 for use with the Xylogics 7053.




J1800 1-2

3-4

5-6

7-8

J2700 1-2

3-4

Out

Out

Out

Out

Out

In

Display

Video blank

N/C

N/C

Sync or Green

Normal operation sync

SW1 S0100

DIP SETTING DESCRIPTION

5

6

7

8

1

2

3

4

On

On

On

Off

On

On

On

On

A24

A25

A26

A27

A28

A29

A30

A31

SW2 S0101


3

4

1

2

5

6

7

8

On/Off

On/Off

On

On/Off

Off

On

On

On

N/C

N/C

Flag

N/C

A32 mode

AM4 switch

AM5 switch

A23 mode http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00553.htm (2 von 3) [25.04.2002 16:20:46]


SW3 S0700


3

4

5

1

2

Off

Off

Off

Off

On

P2 Bus enable

Selects board 3

Selects board 2

Selects board 1

Selects board 0

6

7

8

On

Off

On

N/C

N/C

N/C

Reference

Installation and Configuration Guide for the CG9 Color Frame Buffer, 800-3627.



Sun4/I: Graphics - TAAC-1 Application Accelerator

TAAC-1 Application Accelerator

Sun-4/260/280/360/370/380/390/470/490

501-1383 / 501-1447

POP Board

UNIX ID: dev/taac0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00554.htm (1 von 3) [25.04.2002 16:20:56]


Power

23.9 Amps @ +5Vdc

0.4 Amps @ -5Vdc

0.2 Amps @ +12Vdc

123.9 Watts

DFB Board

DFB Board Jumper and Switch Settings

Jumper JB231

ROW SHUNTS DESCRIPTION

1 B - C http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00554.htm (2 von 3) [25.04.2002 16:20:56]


2-7* Not Used Base addressing

8

9

10

11

12

12

13

8C - 9B

Empty

B-C

B-C

B-C

12D - 13D

B-C

BGIN

VMBG IN/OUT 0

VMBG IN/OUT 1

VMBG IN/OUT 2

Enable 50MHz CLK

VMBG IN/OUT 3

* Jumpers 2-7 are hardwired on board revisions without Switch A26. These boards are not marked with a Sun part number. Jumpers 2-7 are empty on board revisions with Switch A26.

Switch A26

SWITCH

NUMBER

DEFAULT

SETTING*

Sun

4/150**

VME

ADDRESS

5

6

7

1**

2

3

4

On

On

Off

On

Off

On

On

On

On

Off

Off

Off

Off

Off

Bit 25

Bit 26

Bit 27

Bit 28

Bit 29

Bit 30

Bit 31

* Base address = 0x28000000

** Base address = 0xF8000000

Notes

1. Do not disassemble the two-board assembly.

2. The TAAC-1 is not supported with the Sun-2 Color Frame Buffer.

3. The TAAC-1 is not supported with the CG9 Color Frame Buffer.

4. Jumpers JB201-JB204 are hardwired for 16K x 4K RAM.

5. TAAC-1 is not supported under Solaris 2.x (SunOS 5.x).

Reference




Sun4/I: Graphics - VX and MVX Visualization Accelerators

VX and MVX Visualization Accelerators

Board Set

501-1537 / 501-1538

Note

Tighten Frontplane Connector screws 1, 2, 3, and 4 in sequence, turning each screw no more than two turns at a time.



Notes


2. The final unbundled software release was SunVision 1.2.

3. The minimum operating system for SunVision 1.2 is SunOS 4.1.2.

4. SunVision 1.2 requires OpenWindows Version 3.

5. The Sun 4300 CPU and the Sun 4400 CPU require EPROM 4.1.1 when the VX is used as the system console.

6. Set the NVRAM locations to the values shown below when the VX is used as the system console.

LOCATION SETTING

0x1f

0x60c

0x60d

0x60e

0x60f

0x610

0x611

0x612

0x613

00 fc

00

00

00

12

31

40

00

7. Do not use Frontplane Connector 501-1596-01. Use 501-1596-02.

8. The LEDs on the MVX are not used.

References

1. Hardware Installation for the VX and MVX Visualization Accelerators, 800-5424-10.

2. Software Installation for the VX and MVX Visualization Accelerators, 800-6290-10.

Super Frame Buffer

Sun-4/330/370/390/470/490



Power:

14.0 Amps @ +5Vdc

1.45 Amps @ -5Vdc

88.0 Watts

Switch Settings

Interrupt Request Switch S0101

SWITCH SETTING REQUEST BIT

3

4

1

2

Up

Down

Down

Up

2

1

0

VMRQ http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.htm (3 von 6) [25.04.2002 16:21:17]


VME Bus Address Switch S0102

SWITCH SETTING ADDRESS BIT

7

8

5

6

3

4

1

2

On

On

Off

Off

On

On

On

On/Off

A31

A30

A29

A28

A27

A26

A25

Not used

VX Bus Address Switch S0301


7

8

5

6

3

4

1

2

On/Off

On/Off

On

On

On

On

On

On

Not used

Not used

A26

A27

A28

A29

A30

A31

MVX Visualization Accelerator

Sun-4/330/370/390/470/490

Pixel Processor



Power:

14.0 Amps @ +5Vdc

70.0 Watts


Clock Jumper J0101


1-2 In Enable 80MHz clock http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00555.htm (5 von 6) [25.04.2002 16:21:17]


Bus Request Jumper J0901


3-4

5-6

7-8

In

Out

In

VME BUS REQUEST 1

VME BUS REQUEST 2

VME BUS REQUEST 3

Bus Grant Jumper J0902


1-2

3-4

5-9

6-10

7

8

11-12

In

In

In

In

Out

Out

In

BG2 OUT - BG2 IN

BG1 OUT - BG1 IN

BGx OUT - BG3 OUT

BGx IN - BG3 IN

BGx OUT

BGx IN

BG0 OUT - BG0 IN

Bus Control and Arbitration Jumper J1001


1-2

3

4

5-6

In

Out

Out

In

VCC - CTRL

GND

VCC

GND - MODE

Base Address Switch S1303


7

8

5

6

3

4

1

2

Down

Down

Up

Up

Down

Up

Down

Down/Up

A31

A30

A29

A28

A27

A26

A25

Not used



Sun4/I: Graphics - Sun-3/E Monochrome Frame Buffer

Sun-3/E Monochrome Frame Buffer

501-8020

UNIX ID: /dev/bwtwo0

Power

3.0 Amps @ +5Vdc

15.0 Watts



Sun4/I: Graphics - Sun-3/E Color Frame Buffer

Sun-3/E Color Frame Buffer

501-8029

Jumper J100 Settings


J100

J100

J100

1-2

3-4

5-6

J100 7-8

In

Out

In

Out

Base address

=FF400000


Power:

4.0 Amps @ +5Vdc


Sun4/I: Graphics - Sun-3/E Color Frame Buffer

Notes

1. The Sun-3/E Color Frame Buffer requires a 3/E CPU, >=501-8028-07.

2. This board requires SunOS 3.5 or greater.



Sun4/I: Graphics - MG3 ECL Monochrome Frame Buffer

MG3 ECL Monochrome Frame Buffer

Sun-4/110/150/310/330/350/370/390/470/490

501-1247 501-1637 w 3/80 Backpanel

Jumper J5401 Settings


J5401 1-2

1-2

1-2

Out

In

Out

DESCRIPTION

Monitor auto select

Select 1600 x 1280 resolution



Power: 501-1247

0.8 Amps @ +5Vdc

1.2 Amps @ -5Vdc



Notes

1. Set EEPROM location 0x1f to 20.

2. The auto-select feature requires cable 530-1336 or 530-1359.

3. Hi Resolution Monitor 540-1427 must be Motorola revision T or greater for the auto-select feature to operate.



Sun4/I: Graphics - MG4 Analog/ECL Frame Buffer

MG4 Analog/ECL Frame Buffer

Sun-4/310/330/350/370/380/390/470/490

501-1402 w 3/80 Backpane


Power:

3.3 Amps @ +5Vdc

16.5 Watts





Sun-4/110/150/310/330/350/370/380/390/470/490

501-1248 501-1443

BNC DB13W3 w 3/80 Backpanel

J700 Setting


1-2 In Enable clock

UNIX ID: dev/cgfour0 and /dev/bwtwo1 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055a.htm (1 von 2) [25.04.2002 16:21:41]


Power: 501-1443

3.8 Amps @ +5Vdc

19.0 Watts





Sun-4/110/150/310/330/350/370/380/390/470/490

501-1374 501-1505 501-1532 w 3/80 Backpane


J100

J500

J501

J900

1-2

1-2

1-2

2-3

Out

In

Out

In

DESCRIPTION

Monitor ID

V.Y. CLK memory control

OSC 2 CLK

1152 x 900 (on 270-1532 Fab)

UNIX ID: /dev/cgsix0

Power

501-1374

3.5 Amps @ +5Vdc

7.5 Watts

501-1505 and 501-1532

4.9 Amps @ +5Vdc

24.5 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055b.htm (1 von 2) [25.04.2002 16:21:45]


Notes

1. Sun-3/60, Sun-4100, and Sun-4300 CPU boards require EPROM Revision 3.0 or greater.

2. Set CPU EEPROM location 0x1F to 0x20.





CG8 24-bit Color Frame Buffer

Sun-4/110/150

501-1371 501-1518 501-1577

BNC DB13W3 w 3/80 Rear Panel

DB13W3

UNIX ID: /dev/cgeight0

Power

501-1371 and 501-1518

5.5 Amps @ +5Vdc

27.5 Watts

501-1577

4.8 Amps @ +5Vdc

24.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055c.htm (1 von 2) [25.04.2002 16:21:53]


Notes

1. There are no jumpers or switches on this board.

2. Set CPU EEPROM location 0x1F to 0x20.

3. Requires SunOS 4.0 CG8 or 4.0.3 or greater.

4. SunOS 4.0 CG8 is not upgradeable to 4.0.1.

5. CG8 must be 501-1374-04 or greater for use with Sun 3400 and Sun 4300 CPU boards.





MG1 ECL Monochrome Frame Buffer

Sun-4/15/30/40/50/60/65/75

Sun-4/E / SS10 / SS20 / SS600 / SC2000

501-1419 501-8043 w 4/E Backpanel

Jumper JMP4

PINS SETTING

1-2

1-2

1-2

In

Out

Out

DESCRIPTION



Monitor auto select

UNIX ID: /dev/bwtwo0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055d.htm (1 von 2) [25.04.2002 16:21:57]


Power:

1.3 Amps @ +5Vdc

6.5 Watts



Sun4/I: Graphics - MG2 Analog Frame Buffer

MG2 Analog Frame Buffer

Sun-4/15/30/40/50/60/65/75

SS4 / SS5 / SS10 / SS20 / SS600

501-1455 501-8062 w 4/E Backpane

Jumper JMP5


1-2

1-2

In

Out

Select 27C256 EPROM

Select 27C64 EPROM

UNIX ID: /dev/bwtwo0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055e.htm (1 von 3) [25.04.2002 16:22:09]


Power:

0.4 Amps @ +5Vdc

2.0 Watts

Note

The MG2 Frame Buffer produces a 1-bit Analog output.

MG2 Analog Frame Buffer

Sun-4/15/30/40/50/60/65/75

SS4 / SS5 / SS10 / SS20 / SS600

501-1561 501-8077 w 4/E Backpane http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055e.htm (2 von 3) [25.04.2002 16:22:09]



Power:

0.3 Amps @ +5Vdc

1.6 Watts

Note

The MG2 Frame Buffer produces a 1-bit Analog output.





Sun-4/15/30/40/50/60/65/75

SS4 / SS5 / SS10 / SS20

501-1415 501-8044

FAB 270-1415 w 4/E Backpanel

UNIX ID: /dev/cgthree0

Power:

0.7 Amps @ +5Vdc

3.5 Watts

Last updated: December 2, 1996 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0055f.htm (1 von 2) [25.04.2002 16:22:13]



Sun4/I: Memory - Contents

Memory

SIMMs

Sun-4/260/280

Sun-4/330

Sun 4300

Sun 4400

Sun-4/E (4MB)

Sun-4/E (16MB)

Sun-4/E (Combo)



Sun4/I: Memory - SIMMs

SIMMs

An x indicates the SIMM(s) was installed at the factory or included in a memory expansion option.

An s indicates the SIMM(s) was tested and is supported in other systems.

Sun-3, Sun-3x, and Sun386i

SIZE SPEED SIMM P/N 60 60LE 80 150 250

256KB 100ns 501-1349 x

1MB 100ns 501-1239 x

1MB 100ns 501-1346 x x 1MB 120ns 501-1375

1MB 100ns 501-1408

1MB 100ns 501-1424

1MB 120ns 501-1510 x x x x

Sun-4 and Sun-4c

110 370

SIZE SPEED SIMM P/N 20 25 40 50 60 65 75 150 390

256KB 80ns 501-1314

1MB 100ns 501-1408 x x x

330 x

1MB 100ns 501-1466

1MB 100ns 501-1544

1MB 100ns 501-1565

1MB 80ns 501-1697 x x x x x x s x x x

4MB 100ns 501-1625

4MB 100ns 501-1676 x

4MB 80ns 501-1682

4MB 80ns 501-1698 x s x*

4MB 80ns 501-1739

4MB 80ns 501-1812

16MB 80ns 501-1915

16MB 80ns 501-1822 x x x x x x x x x x

* The 501-1682 is not supported on the CPU in a Sun-4/330.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058c.htm (1 von 2) [25.04.2002 16:22:19]

Sun4/I: Memory - SIMMs

Sun-4m

SIZE SPEED SIMM P/N 4/10 4/15 4/30 SS4 SS5 SS10 SS20 SS600 Java

1MB 100ns 501-1466 s*

1MB 100ns 501-1565

1MB 60ns 501-2289 x s*

2MB 60ns 501-2433 x

4MB 80ns 501-1682

4MB 80ns 501-1739

4MB 60ns 501-1991 x x x s* x x 4MB 80ns 501-2460

4MB 60ns 501-4188

8MB 60ns 501-2470

16MB 60ns 501-2059 x x x

16MB 80ns 501-2060

16MB 80ns 501-1785

16MB 80ns 501-2273

16MB 60ns 501-2479 x x x x x x x x

16MB 60ns 501-4216

32MB 60ns 501-2471

32MB 60ns 501-2622

64MB 80ns 501-1930

64MB 60ns 501-2480

64MB 60ns 501-2771 x x x x x x x ** x

* The 501-1466, 501-1565, and 501-1682 SIMMs are supported on the SS600 Expansion Memory.

They are not supported on the system board.

** The 501-2771 64MB SIMM is for Sun internal use only.



Sun4/I: Memory - Sun-4/260/280

Sun-4/260/280

501-1102 501-1254 501-1451 501-1576

8MB ECC 32MB ECC 32MB ECC 16MB ECC

Power

8MB

12.3 Amps @ +5Vdc

61.5 Watts

32MB

14.0 Amps @ +5Vdc

70.0 Watts http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058d.htm (1 von 3) [25.04.2002 16:22:26]


Memory Board LEDs

Jumper Settings

Notes

1. The Sun 4200 CPU requires EPROM 3.0 or greater when more than two 16MB ECC memory boards are installed.

2. 501-1092 or 501-1117 BackpIanes: Install a single memory board in Slot 6 with a 220/270

Terminator, 120-1613-01, installed at location U1203. Remove the terminator when expansion memory boards are installed in Slots 2, 3, 4, and 5.

3. 501-1439 or 501-1498 Backplanes: Install a 220/270 Terminator 120-1613-01, at location

U1203 on the memory board in Slot 1. If placement results in memory boards on both sides of the CPU, remove the terminator at location U1411 on the Sun 3400 CPU, and install terminators on the memory boards in Slots 1 and 7.

4. The 8MB memory board must be >=501-1102-11 to use with the Sun 3400CPU, the FPA, and the FPA+.

5. The 501-1451 32MB board >=501-1451-03 to use with the 501-1576 6MB memory board.

6. Remove jumpers P10, P11, P12, and P13 from the 501-1598 and 501-1832 backplanes when the Sun 3400 board set is installed.



References

1. Sun 501-1102 Memory Board Configuration Procedures, 813-2018.

2. Installation Notes for the 32MB Memory Board, 800-2123.

3. 16 MB ECC Memory Board Installation and Configuration Manual, 813-1066.



Sun4/I: Memory - Sun-4/330

Sun-4/330

501-1723 501-1711

501-1436 501-1317

501-1755

501-1704

8MB Parity w 1MB SIMMS



Jumper Settings


J0901 1-2 In

Out

8 SIMMS installed

16 SIMMS installed

J0902 1-2 In

Out

1MB SIMM

4MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058e.htm (1 von 2) [25.04.2002 16:22:31]

Sun4/I: Memory - Sun-4/330

Power:

1.1 Amps @ +5Vdc

5.5 Watts

Note

The Sun-4/330 memory uses 1MB SIMM 501-1408, 501-1466, 501-1544, 501-1565, or

501-1697, or 4MB SIMM 501-1682.

Reference

Sun 4300 CPU and Memory Board Configuration Procedure, 813-2064.



Sun4/I: Memory - Sun 4300

Sun 4300

Sun-4/310/350/360/370/380/390

501-1563 501-1564 501-1495 501-1703

24MB Parity w 1MB SIMMs




Note

Socket locations are silkscreened on the solder side of this board.

http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058f.htm (1 von 3) [25.04.2002 16:22:37]


Reference

8 Mbyte, 24 Mbyte, and 48 Mbyte Parity Memory Board Installation and Configuration

Manual, 800-3403.

Jumper Settings and Memory Configurations


J2304 In BGR0

J2305

J2306

In

In

BGR1

BGR2

J2307

J2308

In

In

BGR3

IACK

JUMPER SETTING SIMM MODULE

J2309/4MEG Out

J2309/4MEG In

1MB SIMM

4MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0058f.htm (2 von 3) [25.04.2002 16:22:37]


Power

24MB

4.3 Amps @ +5Vdc

21.5 Watts

48MB

5.3 Amps @ +5Vdc

26.5 Watts




Sun 4400

Sun-4/470/490

501-1333 501-1721

32MB ECC 128MB ECC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00590.htm (1 von 3) [25.04.2002 16:22:45]


Power

32MB

15.6 Amps @ +5Vdc

78.0 Watts

128MB

13.7 Amps @ +5Vdc

68.5 Watts

LED Status and Jumper Settings

Memory Board LEDs

Jumper Settings


J0101 1-2

J0301

J0302

1-2

1-2

In

In

Out

Enable SET.RDY

Set for 32MB board

Set for 32MB board

J0301

J0302

J0310

J0311

J0312

J0313

J0314

J0315

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

Out

In

In

In

In

In

In

In

Set for 128MB board

Set for 128MB board

1st memory board

2nd memory board

3rd memory board

4th memory board

5th memory board

6th memory board

Notes

1. The Sun 4400 CPU requires EPROM 3.0 or greater to support the 128MB memory board.

2. SunOS 4.0.3 supports up to 256MB of memory.



3. SunOS 4.1 PSR A requires 4.1 PSR A Sun-4 PMEG Patch to enable over 256MB of memory.

4. A Correctable Error on the sixth 128MB board turns on the CE LED and turns off error logging. Reset power to clear this condition.

Reference

32- and 128-Mbyte Memory Board Installation and Configuration Procedures, 800-3518.



Sun4/I: Memory - Sun-4/E

Sun-4/E

501-8042

4MB ECC

Jumper Descriptions

BOARD SIZE

Sets the memory size of the board.

BOARD ID

Determines where a memory board is mapped into the 256MByte space allocated for memory expansion.

HI/LOW MEM

IN maps the memory board into the lowest 256MBytes of CPU type 0 space.

OUT maps the memory board in the address range between 256MBytes and 512MBytes.



1M/4M DRAM

Specifies 1MByte or 4Mbyte DRAM modules.

Jumper Settings

Memory Mapped into the Upper 256MBytes of Type 0 Address Space

BOARD

SIZE

BOARD

ID

HI/LOW

MEM

1/4MB

DRAM ADDRESS RANGE

J0502 J0503 J0504 J0505 J0506 J0501 PHYSICAL ADDR RANGE

Out

Out

Out

Out

Out

Out

Out

Out

Out

Out

In

In

Out

In

Out

In

Out

Out

Out

Out

Out

Out

Out

Out

0x1000000 - 0x103fffff

0x11000000 - 0x113fffff

0x12000000 - 0x123fffff

0x13000000 - 0x133fffff

Memory Mapped into the Lower 256MBytes of Type 0 Address Space

BOARD

SIZE

BOARD

ID

HI/LOW

MEM

1/4MB


J0502 J0503 J0504 J0505 J0506

Out Out Out Out In

J0501

Out

PHYSICAL ADDR RANGE

0x0000000 - 0x003fffff

Out

Out

Out

Out

Out

Out

Out

In

In

In

Out

In

In

In

In

Out

Out

Out

0x01000000 - 0x013fffff

0x02000000 - 0x023fffff

0x03000000 - 0x033fffff

Notes

1. For specific application dependent memory configurations refer to the SPARCengine 1E ECC

Memory Card User's Manual, 800-8138.

2. The default configuration for Hi Mem/Low Mem is J0506, OUT.

Reference

SPARCengine 1E ECC Memory Card User's Manual, 800-8138.




Sun-4/E

501-8036

16MB ECC

Jumper Descriptions

BOARD SIZE

Sets the memory size of the board.

BOARD ID

Determines where a memory board is mapped into the 256MByte space allocated for memory expansion.

HI/LOW MEM

IN maps the memory board into the lowest 256MBytes of CPU type 0 space.

OUT maps the memory board in the address range between 256MBytes and 512MBytes.



1M/4M DRAM

Specifies 1MByte or 4Mbyte DRAM modules.

Jumper Settings

Memory Mapped into the Upper 256MBytes of Type 0 Address Space

BOARD

SIZE

BOARD

ID

HI/LOW

MEM

1/4MB


J0502 J0503 J0504 J0505 J0506 J0501 PHYSICAL ADDR RANGE

In

In

In

In

In

In

In

In

Out

Out

In

In

Out

In

Out

In

Out

Out

Out

Out

Out

Out

Out

Out

0x1000000 - 0x10ffffff

0x11000000 - 0x11ffffff

0x12000000 - 0x12ffffff

0x13000000 - 0x13ffffff

Memory Mapped into the Lower 256MBytes of Type 0 Address Space

BOARD

SIZE

BOARD

ID

HI/LOW

MEM

1/4MB


J0502 J0503 J0504 J0505 J0506

In In Out Out In

J0501

Out

PHYSICAL ADDR RANGE

0x0000000 - 0x00ffffff

In

In

In

In

In

In

Out

In

In

In

Out

In

In

In

In

Out

Out

Out

0x01000000 - 0x01ffffff

0x02000000 - 0x02ffffff

0x03000000 - 0x03ffffff

Notes

1. For specific application dependent memory configurations refer to the SPARCengine 1E ECC

Memory Card User's Manual, 800-8138.

2. The default configuration for Hi Mem/Low Mem is J0506, OUT.

Reference

SPARCengine 1E ECC Memory Card User's Manual, 800-8138.



Sun4/I: Memory - Sun-4/E Combo

Sun-4/E Combo

501-8060

0MB Parity


J0401 In

Out

Enable Memory

Disable Memory

Note

SunOS 4.0.3e requires the 4.0.3e SRX Feature Tape to support the Combo memory card.


Sun4/I: Memory - Sun-4/E Combo

Reference

SPARCengine 1E Combo Memory Card User's Manual, 800-8152.



Sun4/I: CPU - Contents

CPU


Sun 4100

Sun 4200

Sun 4300

Sun 4400

Sun-4e Architecture

SPARCengine 1 (Sun-4/E)



Sun4/I: CPU - Sun 4100

Sun 4100

Sun 4/110/150

501-1199 501-1237

501-1512 501-1513

501-1462

501-1514

8MB w/o FP 8MB w FPC 16MB w/o FPC

501-1463 501-1464

501-1515 501-1516

501-1465

501-1517

16MB w FPC 32MB w/o FPC 32MB w FPC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (1 von 6) [25.04.2002 16:23:52]


Power: with FPU

13.8 Amps @ +5Vdc

0.1 Amps @ -5Vdc

69.5 Watts

Sun 4100

Sun 4/110/150

501-1656 501-1657 501-1658

8MB w/o FPC 8MB w FPC 1 6MB w/o FPC 1

501-1659 501-1660 501-1661

6MB w FPC 32MB w/o FPC 32MB w FPC http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (2 von 6) [25.04.2002 16:23:52]


Power: with FPU

13.8 Amps @ +5Vdc

0.1 Amps @ -5Vdc

69.5 Watts

501-1199 / 501-1237 / 501-1462 / 501-1463 /

501-1464 / 501-1465

501-1512 / 501-1513 / 501-1514 / 501-1515 /

501-1516 / 501-1517

501-1656 / 501-1657 / 501-1658 / 501-1659 /

501-1660 / 501-1661

Jumper Settings


J0101 1-2

J0600 1-2

3-4

In

In

Out

DESCRIPTION

Enable 57.1MHz clock

27512 Boot PROM

27256 Boot PROM

J700 1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

J800

J900

J1000

1-2

1-2

1-2

J1700

J1701

1-2

1-2

J1800 1-2

1-2

1-2

J1900 1-2

3-4

J1901 1-2

3-4

P2101 1-2

In

In

In

In

In

In

In

In

Out

Out

In

In

Out

Out

Out

In

Out

In

Out

In

In

VME interrupt level 1







Not used

Force reset

In = Shorts 3V battery

Enable UART clock

Enable Ethernet clock

Ethernet Level 2 (In = level 1)

Auto sense Ethernet*

Force Thin Ethernet

Force Thick Ethernet

CPU is VME requester only

CPU is VME requester

CPU is VME reset slave

CPU is VME reset master

Enable VME system clock http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (3 von 6) [25.04.2002 16:23:52]


* Default setting. The auto sense feature requires >=30 milliamps on the +12V return

(example - DEC DELNI).

Notes

1. The Type-4 Keyboard requires CPU >=501-1199-11 or >=501-1237-11.

2. The 501-1384 FPU2 is supported on CPU boards 501-1512, 501-1513, 501-1514, 501-1515,

501-1516, and 501-1517.

3. The final software release for the Sun 4100 is Solaris 2.4.

J100 Cache Line and J400 Memory Strobe

MEMORY SIZE 8MB 16MB 20MB 32MB

SIMM SIZE 256KB 1MB 1MB/256KB 1MB

J100 Pin 1-2

J100 Pin 3-4

In

Out

Out

In

In

Out

Out

In

J400 Pin 1-2

J400 Pin 3-4

J400 Pin 5-6

Out

In

In

In

Out

In

Out

Out

In

In

In

Out

J1300 SIMM Addressing Mode

SIMM

TYPE

MEMORY

SIZE

8MB 16MB 20MB 32MB

256KB 1MB 1MB/256KB 1MB

Same* Pin 1-2

Different* Pin 3-4

In

Out

Out

In

Out

In

In

Out

256KB Pin 5-6

1MB Pin 7-8

In Out

Out In

2MB Pin 9-10 Out Out

<32MB Pin 11-12 In In

32MB Pin 13-1 Out Out

Unused Pin 15-16 Out Out

In

Out

Out

In

Out

Out

Ou

In

Out

Out

In

Out

J1400 SIMM Addressing Mode

SIMM

TYPE

MEMORY

SIZE

8MB 16MB 20MB 32MB

256KB 1MB 1MB/256KB 1MB

Same* Pin 1-2 In Out Out In

Different* Pin 3-4

256KB Pin 5-6

1MB

2MB

Pin 7-8

Out

In

In

Out

Out In

Pin 9-10 Out Out

<32MB Pin 11-12 In In

32M Pin 13-14 Out Out

In

Out

In

Out

In

Out

Out

Out

In

Out

Out

In http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (4 von 6) [25.04.2002 16:23:52]


Unused Pin 15-16 Out Out Out Out

* Same/Different correspond to sets of 256KB or 1MB SIMMs

Sun 4100

SIMM Configurations

501-1314 501-1466

256KB SIMM 1MB SIMM http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd0053f.htm (5 von 6) [25.04.2002 16:23:52]


Reference

Sun 4100 Board Set Configuration Procedures, 813-2049.




Sun 4200

Sun-4/260/280

501-1274 501-1491 501-1522 w FPC-6/4 w FPU-2

2-hi Backpanel w FPC-6/4

2-hi Backpanel

Power

17.2 Amps @ +5Vdc

1.3 Amps @ -5Vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00540.htm (1 von 3) [25.04.2002 16:24:00]


0.4 Amps @ +12Vdc

98.0 Watts

Jumper Settings


J2701 1-2 Out

DESCRIPTION

Debug jumper

J2003 1-2

J2201 1-2

In

In

Connect 3V battery

SCC (UART)clock enable

J2902

J2404

J0304

J0303

J0302

J0301

J2801 1-2

J0401 1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

J2001

J2002

J2401

J2402

J2403

J2404

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

Out

Out

In

In

In

Out

In

In/Out

In

In

In

In

In

In

In

In

Out

Out

In

Out

In

Enet Level 2 (IN for level 1)

Null

Enable VME clock

16 MHz clock enable

46.153 MHz clock enable

External clock

Enable system DVMA

Null








Select 27512 PROM

Select 27256 PROM

CPU is VME requester only

CPU is arbiter/requester

CPU is reset slave

CPU is reset master

Notes

1. 501-1274 must be >=501-1274-12 to use with the Type-4 Keyboard.

2. 501-1274 must be >=501-1274-13 to use with the Xylogics 7053.

3. The Xylogics 7053 requires CPU EPROM 1.7 or greater.

4. Boot PROM 3.0 is required when more than two 16MB memory boards are used.

5. The final software release for the Sun 4200 is Solaris 2.4

Reference

Sun-4200 CPU Board Configuration Procedures, 813-2031.





Sun 4300

Sun-4/310/330/350/360/370/380/390

501-1316 501-1742

8MB w 1MB SIMMS

32MB w 4MB SIMMS

Power

17.5 Amps @ +5vdc

0.2 Amps @ +12vdc

0.2 Amps @ -12vdc http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00541.htm (1 von 3) [25.04.2002 16:24:08]


92.3 Watts

Jumper Settings


J0200 1-2

3-4

5-6

In

In

Out

DESCRIPTION

FPC normally low

FPC normally low

FPC normally high

J0900 1-2

J1900 1-2

1-2

J2100

J2101

J2302

J2303

1-2

In

1-2

1-2

In

In

Out

In

Out

In

In

Enable Sysclock

CPU has 4MB SIMMs

CPU has 1MB SIMMs

Enable 27512 EPROM

Enable 27256 EPROM

Set Ports A,B to RS-232 (+ 12V)

Set Ports A,B to RS-232 (- 12V)

J2302

J2303

2-3

2-3

J2400 1-2

J2402 1-2

2-3

J2502

J2503

1-2

1-2

J2502

J2503

J2701

J2800

J2801

J2803

J2900 1-2

J3001 1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

2-3

2-3

1-2

1-2

1-2

1-2

J3100 1-2

J3101 1-2

In

In

In

Out

In

In

In

In

In

Out

In

In

Out

In

In/Out

In

In

In

In

In

In

In

In

In

Set Ports A,B to RS-423 (+ 5V)

Set Ports A,B to RS-423 (- 5V)

Enable serial port clock

Mouse TD enabled (optional)

Mouse TD grounded (default)

Set Ports C,D to RS-232 (+ 12V)

Set Ports C,D to RS-232 (- 12V)

Set Ports C,D to RS-423 (+ 5V)

Set Ports C,D to RS-423 (- 5V)

Disable VME loopback

Enable VME reset Out

Enable VME arbiter

Enable VME reset IN

Enable 16 MHz clock to backplane

Not connected

Enable VME interrupt level 1







Enable 32 MHz clock

Enable 48 MHz clock

Notes

1. Use 1MB SIMM 501-1408-01, 501-1466-01, 501-1544-01, 501-1565-01, or 501-1697-01.

2. Use 4MB SIMM 501-1682-01 or 501-1739-01.



3. 4MB SIMMs, Option X134A, are not supported on the Sun-4/330 CPU.

4. The Sun 4100 1MB SIMM, 501-1466, may be used in the Sun-4/310 and Sun-4/350 system upgrades.

5. Fuses F0300, F3100, and F3200 use 2 Amp Fuse 150-1174-01.

6. The CPU is set for Ethernet Level 2. Level 1 is not selectable.

7. CPU >=501-1316-04 is required for use with the ISP-80 and FDDI controllers and with LISP software.

8. CPU >=501-1316-03 is required for use with CG5.

9. Boot PROM 3.0 or greater is required to boot from the 60MB 1/4" tape drive in the Mass

Storage Subsystem.

10. Boot PROM 3.0.1 or greater is required to boot from a tape drive on a second SCSI Host

Adapter.

11. Boot PROM 3.0.3 or greater is required with 4MB SIMM modules.

12. Install Fused Shunt, 150-1669-01, at locations J2302, J2303, J2502, and J2503, to provide circuit protection to the M+ (+12Vdc) and M- (-12Vdc) inputs to the UC5170 Serial Port Line

Driver.


Reference

Sun 4300 CPU Board Installation Notes, 800-3119.




Sun 4400

Sun-4/470/490

501-1381 501-1899

0MB 0MB

Power

28.7 Amps @ +5Vdc

0.1 Amps @ +12Vdc

0.1 Amps @ -12Vdc



Jumper Settings


J0100 1-10 Out Used for debug

DESCRIPTION

J0101 1-2

J0201 1-2

In

In

Used for ATE

Used for ATE

J0300 1-2

3-4

5-6

7-8

J0705 1-10

J1901 1-36

J2301 1-2

In

Out

In

Out

If FPC is present

If FPC is present

Avoid a trap when I-Flush instruction is executed

FPC Chaining (only if FPC is present)

Out Used for debug

Out Used for debug

In Enable system clock (33 MHz)

J2600 1-2

J2801

J2802

J2803

J2804

1-2

1-2

1-2

1-2

J3100

J3200

J3201

1-2

1-2

1-2

J3203 1-2

J3603 1-2

2-3

J3604 1-2

2-3

J4600

J4602

J4604

J4605

J4606

J4607

J4608

J4609

J3701

J3703

J3703

1-2

1-2

2-3

J4000 1-2

3-4

5-6

7-8

9-10

11-12

13-14

15-16

1-2

1-2

1-2

1-2

1-2

1-2

1-2

1-2

In

In

In

In

Out Used for debug

Out

In

Out

In

Disable VME arbiter

Enable VME arbiter

Connect P1.SYSRST to VME.RST.IN

Connect VME.RST.OUT to P1.SYSRST

Out

In

Out

In

In

In

In

In

In

In

In

In

In

In

In/Out

In

In

In

In

In

In

In

In

VME loopback mode enabled

Provide 16 MHz Ethernet clock

Enet Level 2 (IN for level 1)

Provide P1.SYSCLCK

Select RS-423 (-5V)

Select RS-232 (-12V)

Select RS-423 (+5V)

Select RS-232 (+12V)

Provide 4.9152 MHz SCC clock

Mouse TD enabled (optional)

Mouse TD grounded (default)

VME IRQ1

VME IRQ2

VME IRQ3

VME IRQ4

VME IRQ5

VME IRQ6

VME IRQ7

Not connected

Used for ATE

Used for ATE

Used for ATE

Used for ATE

Used for ATE

Used for ATE

Used for ATE

Used for ATE http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00005/wcd00542.htm (2 von 3) [25.04.2002 16:24:17]


Notes

1. Install Fused Shunt 150-1669-01 at locations J3603 and J3604 to provide circuit protection to the M+ (+12Vdc) and M- (-12Vdc) inputs to the UC5170 Serial Port Line Driver.

2. The output of Pin-25 from the Serial Port on the 501-1381 CPU is -5Vdc. There is no output from Pin-25 on the 501-1899 CPU.

3. The 501-1381 CPU is not supported in Sun-4/470 serial numbers 136Kxxxx and greater. This chassis has two 50-pin SCSI-2 connectors on the rear EMI cover.

4. SNC 1.2 for Solaris 1.1 requires CPU 501-1381-09 or 501-1899-01.


Reference

Sun 4400 Board Set Installation and Configuration Manual, 800-3269.



Sun4/I: CPU - SPARCengine 1 (Sun-4/E)

SPARCengine 1 (Sun-4/E)

501-8035 501-8058 501-8064

4MB w Weitek

4MB w/o Weitek

16MB w Weitek

Power

5.0 Amps @ +5Vdc

0.1 Amps @ +12Vdc

0.1 Amps @ -12Vdc


Sun4/I: CPU - SPARCengine 1 (Sun-4/E)

Jumper Settings


J0301 1-2 In

DESCRIPTION

20MHz clock enable

J0801 1-2

2-3

J1701 1-2

In

In

In

Use 4MB parity memory (default)

Disable 4MB parity memory

CPU is installed in VME slot 1

Notes

1. Boot PROM 1.4 does not support SunOS 4.1e.

2. Boot PROM 1.5 supports SunOS 4.1e.

3. Boot PROM 1.6 supports SunOS 4.1e.

4. Boot PROM 1.6 and EPROM daughter card 500-8013-05 are installed on CPU 501-8035-12.

5. Daughter Card 500-8013-05 is required if a customer supplied PROM is used with the 1.6

EPROM.

6. A customer supplied EPROM will not function on Daughter Card 500-8013-04, or lower, even if the 1.6 EPROM is installed.

7. The fuses are not field replaceable.

8. The final software release for the Sun-4/E is Solaris 2.4.

Reference

The SPARCengine 1E CPU Card User's Manual, 800-8137.



Sun4/I: Configurations

Configurations

Sun PROM Monitor Commands

Configurations

Handling Static Sensitive Devices

Electronic components on printed circuit boards can be damaged by static electricity. Always wear a grounding strap and use an antistatic mat when handling boards or components.

Reference Documentation

Standard Configurations and Standard Options supported by Sun Microsystems are documented in the

End User Price List, Reseller Price List, Hardware Configuration Guides, Product Brochures, and

Hardware Installation Manuals.

Abbreviations

Assy Assembly

FRU Field Replaceable Unit w With w/o Without

Dip Switches

Rocker and Slide type DIP Switches are used in Sun products. Turn on a Rocker-type switch by pressing down the end of the switch furthest from the OPEN lettering on the switch. Turn on a

Slide-type switch by sliding the switch in the direction of the arrow on the switch. Switches 1 and 2 are shown in the ON position in these illustrations.



Jumpers

Jumpers are used to connect two pins of a Terminal Strip. Two sizes of jumpers are used: 0.100 inch and 2.0 millimeter.

Sun PROM Monitor Commands

To program the EEPROM or NVRAM using the Sun PROM Monitor, enter q followed by the hexadecimal address in the EEPROM or NVRAM to open and display the contents. Change the contents by typing in the new value followed by a carriage return. To exit, type a space and <CR>, or a " .

" and <CR>.



Common EEPROM or NVRAM Parameters

Location 0x14 [Installed Memory]

Amount of installed Memory in hexadecimal

Location 0x15 [Tested Memory]

Amount of memory to test during Power On Self-Test

Location 0x16 [Monitor Screen Size]

00 = 1152x900 (standard resolution)

12 = 1024x1024 (1Kx1K)

13 = 1600x1280 (high resolution) (see 0x50 & 0x51)

14 = 1440x1440

15 = 1024x768 (low resolution)

Location 0x17 [Watchdog Reset Action]

00 = Watchdog Reset returns to the PROM monitor

12 = Watchdog Reset causes a Power On Reset (default)

Location 0x18 [Operating System Boot Device]

00 = polls devices (default)

12 = use EEPROM/NVRAM specified boot device

Location 0x19 - 0x1a [SunOS Boot Device in ASCII]

xy 78 79

xd 78 64

sd 73 64

ie 69 65

id 69 64

gn 67 6e

le 6c 65

Location 0x1b, 0x1c, and 0x1d [Controller, Unit, Partition]

00 00 00 (default)

Location 0x1f [Primary Terminal]

00 = Monochrome Frame Buffer

10 = Serial Port A

11 = Serial Port B

12 = VMEbus and Sun-3/60 P4 Color Frame Buffers

Configure locations 0x60c - 0x613 when VX and MVX Graphics Options are installed.

20 = P4 Color Frame Buffer

Location 0x20 [Power-Up Banner]

00 = Sun Banner

12 = Custom Banner http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004a1.htm (3 von 5) [25.04.2002 16:24:35]


Location 0x21 [Keyboard Click]

00 = turns keyboard click OFF

12 = turns keyboard click ON (default)

Location 0x22 - 0x23 [Diagnostic Boot Device in ASCII]

xy 78 79

xd 78 64

sd 73 64

ie 69 65

id 69 64

gn 67 6e

le 6c 65

Location 0x24, 0x25, and 0x26 [Controller, Unit, Partition]

00 00 00 (default)

Location 0x28 - 0x4f [Diagnostic Boot Path]

These 40 bytes represent the ASCII values for the desired diagnostic boot path.

Location 0x50 [Hi Res # Columns]

50 = 80 columns (standard display)

78 = 120 columns (full screen display)

Location 0x51 [Hi Res # Rows]

22 = 34 rows (standard display)

30 = 48 rows (full screen display)

Location 0x58 [Serial Port A Default Baud Rate]

00 = uses 9600 baud

12 = uses EEPROM/NVRAM defined baud rate

Location 0x59 - 0x5a [Serial Port A Baud Rate]

1200 baud 04 b0

4800 baud 12 c0

9600 baud 25 80

Location 0x5b [Serial Port A DTR/RTS]

00 = asserts DTR and RTS signals

12 = does not assert DTR and RTS signals

Location 0x60 [Serial Port B Default Baud Rate]

00 = uses 9600 baud

12 = uses EEPROM/NVRAM defined baud rate

In the diag position, port B is set to output at 1200 baud.

The setting of location 0x60 - 0x62 is ignored.

Location 0x61 - 0x62 [Serial Port B Baud Rate]

1200 baud 04 b0 http://lios.apana.org.au/~cdewick/sunshack/data/feh/1.4/wcd00004/wcd004a1.htm (4 von 5) [25.04.2002 16:24:35]


4800 baud 12 c0

9600 baud 25 80

Location 0x63 [Serial Port B DTR/RTS]

00 = asserts DTR and RTS signals

02 = does not assert DTR and RTS signals

Location 0x18f [LogoType]

00 = Sun

06 = 3D for CG6

12 = Custom

Location 0x492 [Password Mode Select]

Sun-3 and Sun-4 Boot PROM >= 2.7.1

5E = fully secure mode

01 = command secure mode

All else = non-secure mode

Location 0x493-0x49a [Password Bytes]

Sun-3 and Sun-4 Boot PROM >= 2.7.1

8 bytes of password in ASCII

If the PROM Rev level is 2.8, enter a @ character before each letter of the password. Enter one letter before each location, followed by <Return>. If the password is less than 8 letters, enter

00 in the remaining locations. The hexidecimal value of the letters can also be used to enter the password.

Location 0x60c - 0x60f [VX and MVX Options Boot Code]

31 40 00 00 = Use the VX/MVX as the system console

Location 0x610 - 0x613 [VX and MVX Options Bus Type]

FC 00 00 00 = Use the VX/MVX as the system console

References

1. Sun Bootstrap PROM Security Features User's Guide for the Sun Workstation, 800-8836.

2. Sun Workstation Bootstrap PROM Security Features User's Guide, 800-8843.

3. Sun-3/80 Self-Tests and Monitor Commands, 800-5027.

4. SPARCsystem 300 Series Self-Tests and Monitor Commands, 800-4950.

5. SPARCsystem 400 Series Self-Tests and Monitor Commands, 800-4833.

6. PROM User's Manual, 800-1736.

7. EEPROM Users Guide for Sun-3, Sun-4, and SPARCsystems 300/400, 800-3512.

8. Boot PROM User's Guide, 800-4852.



Sun -4e -4 workstation Handbook

Assistant Bot

Sun Internal ONLY

!!

Key Features

Frequently Answers and Questions

What is the End of Support Life for the Sun-4e workstation?

How does Sun help customers after the End of Support Life?

What is the original hardcopy publication part number for the Sun-4 Handbook?

Related manuals

Table of contents

Sun -4e -4 workstation Handbook

Assistant Bot

Sun Internal ONLY

!!

Key Features

Frequently Answers and Questions

What is the End of Support Life for the Sun-4e workstation?

How does Sun help customers after the End of Support Life?

What is the original hardcopy publication part number for the Sun-4 Handbook?

Related manuals

Cables Direct

SS-323

Sun Microsystems

Sun-3 160 SunStation

FORD HIGGINS

POWERFRAME

Sun Microsystems

2

Sun Microsystems

3/60

Sun Microsystems

Sun-3/60

Sun Microsystems

Sun-1

Sun Microsystems

SunSwift SPARCserver 1000

SINGER

1500 1501

Sun Microsystems

3400

SunLink PV

SL series

SunLink PV

SL series

Table of contents