K-14223-SR2 - CARAVAN COLLECTION PERSIA

SUGGESTED FAUCET CENTERLINE
K-14223-SR2
CARAVANTM COLLECTION PERSIA
VESSEL LAVATORY
/
CUT-OUT TEMPLATE / INSTALLATION INSTRUCTIONS
PREPARATION
BEFORE YOU BEGIN
CAUTION: Risk of personal injury or product damage.
Handle with care. Vitreous china can break or chip if the
product is handled carelessly.
· Observe all local plumbing and building codes.
· Prior to installation, unpack the new lavatory and inspect it
for damage. Return the lavatory to its protective carton
until you are ready to install it.
· Inspect the existing drain and supply tubing. Replace if
necessary.
· These instructions are for installing the lavatory to wood
frame construction. For other installations, supply suitable
bracing and fastening devices of sufficient size and
strength.
· Use the template supplied with the lavatory.
· For replacement installations, make sure the existing
cutout is the same size or smaller than needed for the
new lavatory.
· Use these instructions for wall-mount, self-rimming and
above counter installations. Follow only the instructions
that apply to your installation.
· You can choose between a wall-mount or countertop
faucet installation, depending upon the setting and styling
you desire. A wall-mount faucet is recommended.
· Kohler Co. reserves the right to make revisions in the
design of products without notice, as specified in the Price
Book.
· Kohler lavatory is made according to American National
Standard that it can match the American lavatory fittings .
Any other lavatory fittings may not fit for kohler lavatory.
·
·
·
·
·
·
CUT ALONG THIS LINE
·
WHEN PLOTTING TEMPLATE FULL SIZE:
Make sure horizontal and vertical dimensions
match the dimensions labeled on the template.
·
·
·
·
·
Install the water supplies and drain piping according to the
roughing-in information.
NOTE: The lavatory displayed in the illustration may differ
from your actual product.
Countertop Installations
·
·
·
·
127mm
·
·
·
·
25mm
·
·
·
·
Spout Centerline
Position the template on the countertop.
For Wall-Mount Faucets: Provide sufficient spout
overhang into the lavatory basin. The faucet spout length
must be at least 127mm to provide proper performance.
For Countertop Faucets: Pay special attention to the
spout and handle fit clearance when locating the faucet.
Use the template to locate the faucet spout hole centerline
on the countertop. This centerline is recommended to
provide adequate clearance between the edge of the
lavatory and the spout.
Check for adequate clearance between the backsplash,
faucet spout and handles, and lavatory. Kohler Co.
recommends a clearance of at least 25mm.
Refer to the faucet installation instructions for required
clearance, and mark the preferred faucet hole locations
using a soft lead pencil.
Trace the template on the countertop.
Backsplash
25mm Minimum Clearance
25mm
TOOLS AND MATERIALS
(Not Supplied)
Cut-out Line
Outside Edge of Lavatory
Pencil
Drill
Safety Glasses
Tape Measure
Screwdriver
RIM OF LAVATORY
Plus:
· 18mm drill bit
· Hole Saw
· Safety Shoes
Keyhole Saw
Scissors
CAUTION: Risk of personal injury or product damage.
Handle with care. Product can break, chip or cause injury if
handled carelessly. Get help lifting the lavatory.
Sealant
Countertop Installations
·
NOTE: You may require different, more
specialized tools to install this lavatory to
countertop materials other than wood or
wood composites.
ROUGHING-IN
:
Unit:mm
Reference Value
239.4mm
INSTALL THE LAVATORY
· 18mm
·
·
CL of Fitting
610
51
·
·
·
·
·
·
·
·
·
·
·
·
·
254
·
203
Min
864
·
3mm
6mm
686
Min
·
·
279
229
Min
·
·
30
Recommened ADA Installation
76
·
·
·
·
·
·
162
229
Height
356
Outer
1-1/4" OD
1-1/4"
3/8" Hot
3/8"
102
Inner
Depth
Cut out the opening by carefully following the pencil line
traced from the template.
Temporarily set the lavatory into the countertop cutout to
check for fit.
Remove the lavatory from the countertop.
Drill the faucet holes.
Install the faucet according to the manufacturer s
instructions.
Install the drain. For pop-up drains, use the custom
linkage provided with this lavatory instead of the linkage
supplied with the drain.
Install the custom linkage as shown. Adjust and/or bend
the linkage as required to achieve smooth, effective popup drain operation. Only bend the linkage at the location
shown.
Apply a 3mm bead of sealant around the countertop
cutout hole. Apply the sealant approximately 6mm away
from the cutout hole edge.
Set the lavatory into the countertop cutout. Use care to
avoid smearing the sealant bead. Wipe away any excess
sealant with a clean cloth.
Follow the instructions listed on the sealant label. Allow
the sealant to set for 30 minutes or more before
proceeding.
Connect and tighten the trap to the drain, and complete
the water supply connections to the faucet according to
the instructions packed with the faucet.
Run water into the lavatory and check for leaks.
Clean up with a non-abrasive cleaner.
Bend here only.
413
162
408
Adjust here.
108
Custom Linkage
3/8" Cold
3/8"
Kohler reserves the right to change marked dimensions without prior notice.
Lift Rod
CARE AND CLEANING
·
·
·
·
·
·
·
·
1187650-T01-A
(
)
158
:200436
, 2011
ã
ã Copyright Kohler China Ltd., 2011
0 oC
For best results, keep the following in mind when caring for
your KOHLER product:
· Always test your cleaning solution on an inconspicuous
area before applying to the entire surface.
· Wipe surfaces clean and rinse completely with water
immediately after applying cleaner. Rinse and dry any
overspray that lands on nearby surfaces.
· Do not allow cleaners to soak on surfaces.
· Use a soft, dampened sponge or cloth. Never use an
abrasive material such as a brush or scouring pad to
clean surfaces.
· Be careful not to leave staining materials in contact with
the surface for extended periods of time.
· The ideal cleaning technique is to rinse thoroughly and
blot dry any water from the surface after each use.
o
· Do not use the product in the water below 0 C.
· Please do not use hard materials (like scouring pad) to
clean product surface, especially the product logo.
Download PDF