OWNER'S MANUAL
ОПИСАНИЕ ПУЛЬТА
AIRДИСТАНЦИОННОГО
CONDITIONER УПРАВЛЕНИЯ
OWNER'S MANUAL
REMOTE2:1ROLLER
ILLUSTRATION
ДЛЯ КОНДИЦИОНЕРА
REMOTE CONTROLLER
)RUDLUFRQGLWLRQHUV:
ACI/AOU-35HPR1
ACI/AOU-53HPR1
ACI/AOU-71HPR1
ACI/AOU-105HPS3
ACI/AOU-140HPS3
AFI/AOU-53HPR1
AFI/AOU-105HPS3
AFI/AOU-140HPS3
AFI/AOU-180HPS3
ATI/AOU-53HPR1
ATI/AOU-105HPS3
ATI/AOU-140HPS3
7KDQN\RXYHU\PXFKIRUSXUFKDVLQJRXUDLUFRQGLWLRQHU3OHDVHUHDGWKLV
Thank you very much for purchasing our air conditioner .
RZQHU
VPDQXDOFDUHIXOO\EHIRUHXVLQJ\RXUDLUFRQGLWLRQHU.
Please read this owner's manual carefully before using
your air conditioner .
NOTE
1.The outline figure on cover is for reference only, which
may differ from what you purchased.
2. Make sure to read chapter PRECAUTIONS before
you operate the air conditioner.
3. This manual is available for model R05/BG.
4. R05/BGE can be applicable for cool only type and
cool&heat type air conditioners.
CONTENTS
PRECAUTIONS.........................................................1
MODEL AND SPECIFICATION.....................................1
BUTTONS AND THEIR FUNCTIONS..............................2
INDICATORS AND FUNCTIONS....................................5
OPERATION INSTRUCTIONS.......................................6
INSTALL AND REPLACE BATTERIES...............................6
AUTO OPERATION............................................................6
COOL/HEAT/FAN OPERATION..........................................6
DRY OPERATION.....................................................7
TIMER OPERATION...................................................7
NOTE-CONTENTS
0
PRECAUTIONS
Set TIME ON and TIME OFF simultaneously
Curtain, door or the like objects will prevent the remote signal from
being received by air conditioner.
1. Set TIME ON according to procedures 1 and 2 specified in
TIME ON operation.
Do not get the interior of remote controller wet. It is forbidden to expose
it to direct sunlight or locate it in the place with high temp.
2. Set TIME OFF as the procedures 1 and 2 specified in TIME
OFF operation.
Malfunction may occur if infrared signal receiver on air conditioner is
3. If both the set time of TIME ON and TIME OFF not exceed
exposed to sunlight. Please shelter the signal receiver from sunlight
10 hours, time OFF operation will activated 0.5 hour later
with curtain.
than time ON operation. If both the set time of TIME ON and
Please remove the nearby electronic device for they may affect the
TIME OFF exceed 10 hours, time OFF operation will be
performance of remote controller. If necessary, contact the local Midea
service centre or technical support centre.
activated 1 hour later than time ON operation.
4. 0.5s after setting, remote controller will send TIME ON
Do not put the used or different batteries into the remote controller,
otherwise remote controller will fail to send signal.
Please remove the batteries before long period unused, otherwise the
command to the unit.
Modification of timer operation
Press corresponding button and readjust the time of time
remote controller may be damaged.
ON and time OFF. Adjust the time figure to 0.00 to cancel the
If pressing the button reset the remote controller, which indicates low
timer operation.
battery, please replace the batteries.
NOTE: The time set in timer operation is the relative figure
If no receiving sound is heard from indoor unit or
based on the clock on remote controller. Adjusting clock is
on remote controller
does not flash, please replace the batteries.
unavailable when TIME ON or TIME OFF is activated.
Effective transmitting distance of remote controller is 8m, please aim the
signal sending part to the receiver on air conditioner.
MODEL AND SPECIFICATION
Model
R05/BGE
Rated voltage
3.0V(2 pieces of LR03 7# batteries)
Min voltage for sending signal of CPU 2.4V
Effective receiving distance
8m 11m
Operation condition
-5~60 OC
1
PRECAUTIONS-MODEL AND SPECIFICATION
OPERATION INSTRUCTIONS
8
NOTE: On FAN mode, temp is nonadjustable and ECO is
BUTTONS AND THEIR FUNCTIONS
ineffective. Procedure 2 is omitted.
DRY operation
1. Press MODE to select DRY.
2. Adjust temp via
and
. Generally the range is 17 ~30 .
AUTO
3. Press ON/OFF and running indicator light on indoor unit is
COOL
lightened. Air conditioner will work on DRY mode. Turn off
the unit via ON/OFF.
Mode setting
TEMP
SET
DRY
1
2 Fan speed setting
CLOCK
HEAT
SET
HOUR
4. On DRY mode, ECO and FAN SPEED are unavailable.
FAN
Adjust
FAN SPEED
4
3
Timer operation
TIME ON and TIME OFF are used to turn on and turn off the
Adjust
FAN
SPEED
MODE
unit at the set time respectively.
TIME ON operation
1. Press TIME ON, icon SET, HOUR and ON are lightened.
2. Press TIME ON again and adjust the time.
ON/OFF
Horiz swing
5
7
3. Keep pressing this button, the time will increase by 0.5
hour. When the set time exceeds 10 hours, pressing the
Vert. swing
8
button will increase the time by 1 hour.
4. 0.5s after setting, remote controller will send TIME ON
SWING
AIR DIRECTION
CLOCK
SWING
OK
TIME ON
ECO
TIME OFF
RESET LOCK C/H
Reset
12
Lock
13
Cool/heat
15
command to the unit.
TIME OFF operation
1. Press TIME OFF, icon SET, HOUR and OFF are lightened.
6
Air direction setting
9
Time setting
10
Time ON
11
Time OFF
14
Confirm button
16
Economic operation
2. Press TIME OFF again and adjust the time.
3. Keep pressing this button, the time will increase by 0.5
hour. When the set time exceeds 10 hours, pressing the
button will increase the time by 1 hour.
4. 0.5s after setting, remote controller will send TIME OFF
command to the unit.
Chart 1
7
OPERATION INSTRUCTIONS
BUTTONS AND THEIR FUNCTIONS 2
MODE: Once pressing, running mode will be selected in
Fan speed: Press FAN SPEED to display the current wind
the following sequence:
speed. AUTO, LOW, MED and HIGH can be selected. The
AUTO
COOL
DRY
HEAT
default state is high fan speed for the unit without medium
FAN
NOTE: No heating mode for cool only type unit.
fan speed.
Economic operation: This icon will be lightened or off when
FAN SPEED: Fan speed will be selected in following
pressing ECO button.
sequence once pressing this button:
AUTO
LOW
MED
HIGH
NOTE: All the above icons will be displayed only when
the remote controller is electrified for the first
time or reset.
Adjust : Decrease the set temp. Keeping pressing will
decrease the temp with 1
Adjust
per 0.5s.
Increase the set temp. Keeping pressing will
increase the temp with 1
per 0.5s.
OPERATION INSTRUCTIONS
Install and replace batteries
Install 2 pieces of 7# alkaline batteries.
Slide the cover to install batteries and make sure to
ON/OFF: For turning on or turning off the air conditioner.
AIR DIRECTION: Activate swing function of air deflector. Once
place them in right pole.
AUTO operation
pressing, air deflector will turn 6 . For normal operation and
Switch on the power and running indicator light on indoor unit
better cooling and heating effect, deflector will not turn to the
flashes.
degree which is the state of deflector when the unit is turned
1. Press MODE to select AUTO.
off.( Only available when remote controller is used with
2. Adjust temp via
corresponding unit.)
3. Press ON/OFF and running indicator light on indoor unit is
and
. Generally the range is 17 ~30 .
HORIZ SWING: Activate or turn off horizontal swing
lightened. Air conditioner will work on AUTO mode and fan
function. (Only available when remote controller is used
speed is AUTO which is nonadjustable.
with corresponding unit.)
VERT SWING: Activate or turn off vertical swing function.
4. ECO is effective on AUTO operation.
(Only available when remote controller is used with
COOL/HEAT/FAN operation
1. Press MODE to select COOL, HEAT or FAN.
corresponding unit.)
CLOCK: Display the current time. (12:00 is displayed when
3. Press FAN SPEED to select AUTO, LOW, MED or HIGH.
2. Adjust temp via
and
. Generally the range is 17 ~30 .
resetting or electrifying for the first time.) Press CLOCK for
4. Press ON/OFF and running indicator light on indoor unit is
5s, icon indicating hour will flash with 0.5s. Press it again,
lightened. Air conditioner will work on the set mode. Stop
icon indicating minute will flash with 0.5s.
operation via ON/OFF.
3
and
BUTTONS AND THEIR FUNCTIONS
are used
OPERATION INSTRUCTIONS 6
to adjust the figure. Setting or modification is effective only
by pressing OK button to make confirmation.
TIME ON: For time ON setting. Once pressing this button,
the time will increase by 0.5 hour. When the set time exceeds
10 hours, pressing the button will increase the time by 1 hour.
INDICATORS AND FUNCTIONS
Temp
1
Transmitting display
2
Running mode
AUTO
COOL
Time
6
Lock
SET
HOUR
FAN
Economic operation
8
ON
OFF
7
Time ON/OFF
9
Fan speed
FAN SPEED
RESET (inner located): Press this button with a needle of
Chart 2
Temp: Display the set temperature. Adjust temperature via
1mm to cancel the current setting and reset remote controller.
and
12
13
. No display in this area if the unit is on FAN mode.
LOCK (inner located): Press this button with a needle of
Transmitting display: The icon will flash once when the signal
1mm to lock or unlock the current setting.
is sent by remote controller.
ON/FF: Icon is displayed when the remote controller is turned
14
OK: Used to confirm the time setting and modification.
15
COOL/HEAT (inner located): Press this button with a needle
of 1mm to shift mode between COOL only and COOL&HEAT.
During setting, back light will be lightened. Factory default
mode is COOL &HEAT.
16
5
SET
CLOCK
HEAT
the time will increase by 0.5 hour. When the set time exceeds
10 hours, pressing the button will increase the time by 1 hour.
TEMP
DRY
TIME OFF: For time OFF setting. Once pressing this button,
Adjust the figure to 0.00 will cancel time ON setting.
ON/OFF
4
Adjusting the figure to 0.00 will cancel time ON setting.
11
3
ECO: Activate or turn off economic operation mode. It is
suggested to turn on this function when sleeping. (Only
available when remote controller is used with corresponding
unit.)
on, or vice versa.
Running mode: Press MODE to display current running mode.
AUTO, COOL, DRY, HEAT and FAN can be selected. (HEAT
function is invalid for cool only type unit.)
Time: Display the current set time. Press CLOCK for 5s, icon
indicating hour will flash. Press this button again, icon indicating
minute will flash. And
are used to adjust the figure. Setting
or modification is effective only by pressing OK button to make
confirmation.
Lock: The icon will be lightened or off when pressing LOCK.
In locked state, all the buttons are ineffective except button
LOCK.
Time ON/OFF: In the state of time ON, icon ON will be
lightened, which is the same to the state of time OFF.
Setting timer ON and OFF simultaneously, both icons ON
and OFF are displayed.
4
BUTTONS AND THEIR FUNCTIONS
INDICATORS AND FUNCTIONS
5
Download PDF