Cross Technologies 2000-12 Power Supply, +12 VDC Instruction manual

Model 2000-12
Instruction Manual
Power Supply
April 2012, Rev. A
•
2000 POWER SUPPLY
-12
GND
+12
•
CAUTION - RISK OF ELECTRICAL
SHOCK - DO NOT OPEN!!!
CROSS TECHNOLOGIES, INC.
POWER
CROSS TECHNOLOGIES, INC.
IF
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment. Printed in USA.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
C ROSS T ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
INSTRUCTION MANUAL
MODEL 2000-12 Power Supply
TABLE OF CONTENTS
PAGE
Warranty
2
1.0 General
3
1.1 Equipment Description
3
1.2 Technical Characteristics
3
2.0 Installation
4
2.1 Mechanical
4
2.2 Controls & Indicators
4
2.3 Input & Output Signals
4
2.4 Changing the On-Card Fuse
4
2.5 Operation
7
2.5.1 Installing and operating the 2001-01
7
2.5.2 Replacing the fuse in the rear panel
7
3.0 Environmental Use Information
8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies, Inc.’s
obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s option,
replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall not be liable
for any special, indirect, or consequential damages. This warranty does not cover parts or
equipment which have been subject to misuse, negligence, or accident by the customer during
use. All shipping costs for warranty repairs will be prepaid by the customer. There are not other
warranties, express or implied, except as stated herein.
C ROSS T ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2000-12 Manual, Rev. A
Page 2
04/11/12
MODEL 2000-12 POWER SUPPLY
SECTION 1 GENERAL
1.1 Equipment Description - The 2000-12 Power Supply is a switching power supply which provides
regulated +12 VDC at 1.2 amps and -12 VDC at 0.5 amps with a 100-240 ±10% VAC, 47 to 63 Hz input
and can be used with Cross Series 2000 products. The input AC connector is IEC 320 C13 and the
DC outputs are on a barrier strip. The 2000-12 can be mounted on an 1.75”x 19.0” rack mount panel
(option -R).
•
2000 POWER SUPPLY
-12
GND
+12
•
CAUTION - RISK OF ELECTRICAL
SHOCK - DO NOT OPEN!!!
CROSS TECHNOLOGIES, INC.
POWER
CROSS TECHNOLOGIES, INC.
TABLE 1.0
DC Output Characteristics
Voltage / Current
Indicators
DC Power
Other
Connector, AC Input
Connector, DC Output
Size, Bench Top
Size, Rack Mount (-R)
IF
2000-12 POWER SUPPLY SPECIFICATIONS
AC Input Characteristics
Voltage
Frequency
Power, maximum
Load Regulation, max.
Power Supply type
Switching Frequency
100-240 ±10% VAC
47 - 63 Hz
50 watts
+12 VDC/ 1.2 amps,
-12 VDC / 0.5 amps
±5%
Switcher
50 kHz, typical
Green LED
IEC 320 C13
Barrier Strip
4.7” wide X 1.75”high X 8.5” deep
19 inch standard chassis 1.75”high X 9.0”deep
(Optional)
*+10 to +40 degrees C; Specifications subject to change without notice
2000-12 Manual, Rev. A
Page 3
04/11/12
2.0
2.1
Installation
Mechanical - The 2000-12 is packaged in an aluminum extrusion. The -R option is mounted on a
1.75” X 19” panel that can be mounted to a rack using the 4 holes at the ends. See Figure 2.1.
REAR SCREWS (4EA)
REAR
PANEL
EXTRUSION
FRONT PANEL
2000 POWER SUPPLY
CROSS TECHNOLOGIES,
INC.
POWER
RACK MOUNT PANEL
(FOR -R MODELS ONLY)
FRONT SCREWS (4EA)
2.2
Controls and Indicators - Figure 2.2 shows the front panel indicator.
2.3
Input / Output Signals - Figure 2.3 shows the input and output signals to the 2000-12.
2.4
Accessing and Changing On-Card Fuse - The primary fuse is in the AC connector fuse box
(Figure 2.3, Section 2.5.2). Figure 2.4 shows the secondary fuse on the power supply.
To remove the power supply from the extrusion for access to the secondary fuse:
1.) Remove four (4) rear panel screws (see Figure 2.1).
2.) Gently pull the power supply assembly completely out of the extrusion.
3.) With AC Power disconnected, replace fuse with a 2.0 amp fuse (Figure 2.4).
4.) Gently push the power supply assembly completely in to the extrusion.
5.) Install four (4) rear panel screws.
2000-12 Manual, Rev. A
Page 4
04/11/12
2000 POWER SUPPLY
CROSS TECHNOLOGIES, INC.
DS1 - DC
POWER LED
Lights green
when DC power
is present.
POWER
J1 - AC INPUT
The100-240 ±10% VAC, 47 - 63 HZ input . The fuse is
in the tray below this and is a 2.0 amp fuse. There is
also a 2.0 amp fuse on the internal power supply.
CAUTION - RISK OF ELECTRICAL
SHOCK - DO NOT OPEN!!!
-12
GND + 1 2
Mounting
Screws
CROSS TECHNOLOGIES, INC.
FU5E BOX
A 2.0 amp fuse. There is also a
spare 2.0 amp fuse in the box.
J2 - DC POWER OUTThe +12 VDC (1.2 A) and -12
VDC (0.5 A) regulated DC
output voltage.
FIGURE 2.3 2000-12 Rear Panel Inputs and Outputs
2000-12 Manual, Rev. A
Page 5
04/11/12
POWER SUPPLY FUSE
2.0 amp fuse
DS1
+
GND
DC
POWER
OUT
–
AC
POWER
IN
SWITCHING POWER SUPPLY
- Provides the +12 VDC (1.2 A) and -12 VDC (0.5 A)
regulated DC output voltage
FIGURE 2.4
2000-12 On-Card AC Power Supply Fuse
(See Section 2.4 for instructions on removing the unit from the extrusion)
2000-12 Manual, Rev. A
Page 6
04/11/12
2.5
Installation / Operation -
2.5.1
Installing and Operating the 2000-12 1.) Connect the DC power to the Series 2000 unit.
2.) Connect the 2000-12 to 100-240 ±10% VAC, 43 - 60 Hz.
3.) Be sure DS1 (green, DC Power) is on (Figure 2.2).
2.5.2
Replacing the fuse in the rear panel fuse box (Figure 2.3) 1.) Remove the 100-240 ±10% VAC, 43 - 60 Hz to the 2000-12
2.) Pull out the fuse box below the AC input connector (Figure 2.3).
3.) Pry out the fuse in the back slot and measure it to see if it is open.
4.) If the fuse is open determine the cause of the blown fuse and repair this.
5.) After the cause of the blown fuse is corrected, replace the open fuse with the
2.0 amp fuse in the front section.
6.) Apply 100-240 ±10% VAC, 43 - 60 Hz to the 2000-12 and be sure DS1
(green, DC Power) is on Figure 2.2.
FUSE DRAWER
SPARE FUSE
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
INPUT
~
~
100-240± 10%VAC
47-63 Hz
2A MAX
2000-12 Manual, Rev. A
Page 7
FUSE
TYPE T 2A GDC
250 VOLT
FOR 100 - 240 V~
04/11/12
3.0 Environmental Use Information
A. Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C. Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between units
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the
supply circuit and the effect that overloading of circuits could have on over current protection and
supply wiring. Appropriate consideration of equipment name plate rating should be used when
addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connection to the
Branch (use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be
removed. If the Top Cover is removed the ground strap and associated screw MUST BE
REINSTALLED prior to Top Cover screw replacement. FAILURE TO DO this may cause
INGRESS and/or EGRESS emission problems.
2000-12 Manual, Rev. A
Page 8
04/11/12
C ROSS T ECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
(770) 886-8005
FAX (770) 886-7964
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
Printed in USA
2000-12 Manual, Rev. A
Page 9
04/11/12