NEC MultiSync P461 User Guide Manual

User’s Manual
MultiSync P401
MultiSync P461
MultiSync P521
Downloaded From TV-Manual.com Manuals
Index
Declaration of conformity ............................................................................................................................. English-1
Important Information ................................................................................................................................... English-2
WARNING, CAUTION ........................................................................................................................ English-2
Declaration ................................................................................................................................................... English-2
Safety Precautions, Maintenance & Recommended Use ............................................................................ English-3
Contents ....................................................................................................................................................... English-4
Installation .................................................................................................................................................... English-5
Parts Name and Functions .......................................................................................................................... English-7
Control Panel ...................................................................................................................................... English-7
Terminal Panel .................................................................................................................................... English-8
Wireless Remote Control ................................................................................................................... English-10
Operating Range for the Remote Control ........................................................................................... English-11
Handling the remote control ........................................................................................................... English-11
Setup ............................................................................................................................................................ English-12
Connections ................................................................................................................................................. English-14
Wiring Diagram ................................................................................................................................... English-14
Connecting a Personal Computer ...................................................................................................... English-15
Connecting a DVD Player with HDMI out ........................................................................................... English-15
Connecting a Computer with DisplayPort ........................................................................................... English-15
Basic Operation ........................................................................................................................................... English-16
Power ON and OFF Modes ................................................................................................................ English-16
Power Indicator .................................................................................................................................. English-17
Using Power Management ................................................................................................................. English-17
Selecting a video source .................................................................................................................... English-17
Picture Aspect .................................................................................................................................... English-17
Information OSD ................................................................................................................................. English-18
Picture Mode ...................................................................................................................................... English-18
OSD (On-Screen-Display) Controls ............................................................................................................. English-19
PICTURE ............................................................................................................................................ English-20
ADJUST ............................................................................................................................................. English-20
AUDIO ................................................................................................................................................ English-21
SCHEDULE ........................................................................................................................................ English-21
PIP ...................................................................................................................................................... English-22
OSD .................................................................................................................................................... English-22
MULTI DISPLAY ................................................................................................................................. English-23
DISPLAY PROTECTION .................................................................................................................... English-24
ADVANCED OPTION ......................................................................................................................... English-24
Remote Control Function ............................................................................................................................. English-27
Controlling the LCD monitor via RS-232C Remote Control ......................................................................... English-29
Controlling the LCD monitor via LAN Control .............................................................................................. English-30
Features ....................................................................................................................................................... English-33
Troubleshooting ........................................................................................................................................... English-34
Specifications - P401 ................................................................................................................................... English-35
Specifications - P461 ................................................................................................................................... English-36
Specifications - P521 ................................................................................................................................... English-37
Pin Assignment ............................................................................................................................................ English-38
Manufacturer’s Recycling and Energy Information ...................................................................................... English-39
www.necdisplaysolutions.com
Downloaded From TV-Manual.com Manuals
This device complies with Part 15 of FCC Rules. Operation is subject to the following two conditions. (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
U.S. Responsible Party:
Address:
Tel. No.:
NEC Display Solutions of America, Inc.
500 Park Boulevard, Suite 1100
Itasca, Illinois 60143
(630) 467-3000
Type of Product:
Display Monitor
Equipment Classification:
Class B Peripheral
Model:
MultiSync P401 (L408TM)
MultiSync P461 (L468TN)
MultiSync P521 (L528N7)
We hereby declare that the equipment specified above
conforms to the technical standards as specified in the FCC Rules.
Canadian Department of Communications Compliance Statement
DOC: This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
C-UL: Bears the C-UL Mark and is in compliance with Canadian Safety Regulations according to CAN/CSA C22.2 No. 60950-1.
FCC Information
1. Use the attached specified cables with the MultiSync P401 (L408TM)/MultiSync P461 (L468TN)/MultiSync P521 (L528N7)
colour monitor so as not to interfere with radio and television reception.
(1) Please use the supplied power cord or equivalent to ensure FCC compliance.
(2) Please use the supplied shielded video signal cable, Mini D-SUB 15 pin to Mini D-SUB 15 pin.
2. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by
one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult your dealer or an experienced radio/TV technician for help.
If necessary, the user should contact the dealer or an experienced radio/television technician for additional suggestions.
The user may find the following booklet, prepared by the Federal Communications Commission, helpful: “How to Identify
and Resolve Radio-TV Interference Problems.” This booklet is available from the U.S. Government Printing Office, Washington,
D.C., 20402, Stock No. 004-000-00345-4.
Windows is a registered trademark of Microsoft Corporation.
NEC is a registered trademark of NEC Corporation.
OmniColor is a registered trademark of NEC Display Solutions Europe GmbH in the countries of EU and
Switzerland.
DisplayPort is trademarks of Video Electronics Standards Association.
All other brands and product names are trademarks or registered trademarks of their respective owners.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC.
English-1
Downloaded From TV-Manual.com Manuals
English
DECLARATION OF CONFORMITY
Important Information
WARNING
TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS UNIT TO RAIN OR MOISTURE. ALSO, DO NOT
USE THIS UNIT’S POLARIZED PLUG WITH AN EXTENSION CORD RECEPTACLE OR OTHER OUTLETS UNLESS
THE PRONGS CAN BE FULLY INSERTED.
REFRAIN FROM OPENING THE CABINET AS THERE ARE HIGH VOLTAGE COMPONENTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK, MAKE SURE POWER CORD IS UNPLUGGED FROM
WALL SOCKET. TO FULLY DISENGAGE THE POWER TO THE UNIT, PLEASE DISCONNECT THE
POWER CORD FROM THE AC OUTLET. DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol warns user that uninsulated voltage within the unit may have sufficient magnitude to cause
electric shock. Therefore, it is dangerous to make any kind of contact with any part inside this unit.
This symbol alerts the user that important literature concerning the operation and maintenance of this unit
has been included. Therefore, it should be read carefully in order to avoid any problems.
CAUTION: Please use the power cord provided with this display in accordance with the table below. If a power cord is not
supplied with this equipment, please contact your supplier. For all other cases, please use a power cord that matches the
AC voltage of the power outlet and has been approved by and complies with the safety standard of your particular country.
North America
European
Continental
U.K.
Chinese
Japanese
Region
U.S.A./Canada
EU (except U.K.)
U.K.
China
Japan
Voltage
120*
230
230
220
100
Plug Type
Plug Shape
*When operating the MultiSync P401 (L408TM)/MultiSync P461 (L468TN)/MultiSync P521 (L528N7) monitor with its AC 125-240V
power supply, use a power supply cord that matches the power supply voltage of the AC power outlet being used.
NOTE: This product can only be serviced in the country where it was purchased.
Declaration
Declaration of the Manufacturer
We hereby certify that the color monitor MultiSync
P401 (L408TM)/MultiSync P461 (L468TN)/MultiSync
P521 (L528N7) are in compliance with
and marked with
Council Directive 2006/95/EC:
– EN 60950-1
Council Directive 2004/108/EC:
– EN 55022
– EN 61000-3-2
– EN 61000-3-3
– EN 55024
NEC Display Solutions, Ltd.
4-13-23, Shibaura,
Minato-Ku
Tokyo 108-0023, Japan
English-2
Downloaded From TV-Manual.com Manuals
•
•
•
•
•
FOR OPTIMUM PERFORMANCE, PLEASE NOTE THE
FOLLOWING WHEN SETTING UP AND USING
THE MULTI-FUNCTION MONITOR:
Immediately unplug your monitor from the wall outlet and refer
servicing to qualified service personnel under the following
conditions:
DO NOT OPEN THE MONITOR. There are no user
serviceable parts inside and opening or removing covers
may expose you to dangerous shock hazards or other risks.
Refer all servicing to qualified service personnel.
•
When the power supply cord or plug is damaged.
•
If liquid has been spilled, or objects have fallen into the monitor.
•
If the monitor has been exposed to rain or water.
•
If the monitor has been dropped or the cabinet damaged.
•
If you notice any structural damage such as cracks or
unnatural wobbling.
•
If the monitor does not operate normally by following
operating instructions.
Do not spill any liquids into the cabinet or use your monitor
near water.
Do not insert objects of any kind into the cabinet slots, as
they may touch dangerous voltage points, which can be
harmful or fatal or may cause electric shock, fire or
equipment failure.
Recommended Use
Do not place any heavy objects on the power cord.
Damage to the cord may cause shock or fire.
Do not place this product on a sloping or unstable cart,
stand or table, as the monitor may fall, causing serious
damage to the monitor.
•
For optimum performance, allow 20 minutes for warm-up.
•
Rest your eyes periodically by focusing on an object at least
5 feet away. Blink often.
•
Position the monitor at a 90° angle to windows and other
light sources to minimize glare and reflections.
•
Clean the LCD monitor surface with a lint-free, non-abrasive
cloth. Avoid using any cleaning solution or glass cleaner!
•
Adjust the monitor’s brightness, contrast and sharpness
controls to enhance readability.
•
Avoid displaying fixed patterns on the monitor for long
periods of time to avoid image persistence (after image
effects).
•
Get regular eye checkups.
•
Do not mount this product face up, face down or upside
down for an extended period of time as it may cause
permanent damage to the screen.
•
The power supply cord you use must have been approved
by and comply with the safety standards of your country.
(Type H05VV-F 3G 1mm2 should be used in Europe)
•
In UK, use a BS-approved power cord with molded plug
having a black (13A) fuse installed for use with this monitor.
•
Do not place any objects onto the monitor and do not use
the monitor outdoors.
•
The lamps in this product contain mercury. Please
dispose according to state, local or federal law.
To realize the maximum ergonomic benefits, we recommend
the following:
•
Do not bend, crimp or otherwise damage the power cord.
•
•
If glass is broken, handle with care.
Use the preset Size and Position controls with standard
signals.
•
Do not cover vent on monitor.
•
Use the preset Color Setting.
•
Do not use monitor in high temperature, humid, dusty, or
oily areas.
•
Use non-interlaced signals.
•
•
If monitor or glass is broken, do not come in contact with the
liquid crystal and handle with care.
Do not use primary color blue on a dark background, as it is
difficult to see and may produce eye fatigue due to
insufficient contrast.
•
Allow adequate ventilation around the monitor, so that heat
can properly dissipate. Do not block ventilated openings or
place the monitor near a radiator or other heat sources.
Do not put anything on top of the monitor.
Cleaning the LCD Panel
•
When the liquid crystal panel is stained with dust or dirt,
please wipe with soft cloth gently.
The power cable connector is the primary means of detaching
the system from the power supply. The monitor should be
installed close to a power outlet, which is easily accessible.
•
Please do not rub the LCD panel with hard material.
•
Please do not apply pressure to the LCD surface.
•
Please do not use OA cleaner it will cause deterioration or
discolor on the LCD surface.
•
•
•
Ergonomics
Do not move or mount this product by hanging a rope or wire
to the backside handle.
Do not mount or secure this product by using the backside
handle. It may fall and cause personal injury.
Handle with care when transporting. Save packaging for
transporting.
•
If using the cooling fan continuously, it is recommended to
wipe holes clean a minimum of once a month.
•
Please clean the holes of back cabinet to reject dirt and
dust at least once a year because of set reliability.
•
When using a LAN cable, do not connect to a peripheral
device with wiring that might have excessive voltage.
Connecting to a TV*
•
Cable distribution system should be grounded (earthed) in
accordance with ANSI/NFPA 70, the National Electrical
Code (NEC), in particular Section 820.93, Grounding of
Outer Conductive Shield of a Coaxial Cable.
•
The screen of the coaxial cable is intended to be connected
to earth in the building installation.
Cleaning the Cabinet
•
Unplug the power supply
•
Gently wipe the cabinet with a soft cloth
•
To clean the cabinet, dampen the cloth with a neutral
detergent and water, wipe the cabinet and follow with a dry
cloth.
NOTE: DO NOT clean with benzene thinner, alkaline detergent,
alcoholic system detergent, glass cleaner, wax, polish
cleaner, soap powder, or insecticide. Rubber or vinyl
should not be in contact with the cabinet for an
extended period of time. These types of fluids and
materials can cause the paint to deteriorate, crack or
peel.
* The product you purchased may not have this feature.
English-3
Downloaded From TV-Manual.com Manuals
English
Safety Precautions, Maintenance & Recommended Use
Contents
Your new MultiSync monitor box* should contain the following:
•
LCD monitor
•
Cable cover
•
Power cord*1
•
Clamp x 3
•
Video Signal Cable
•
Screw (M4 x 10) x 9
•
Wireless Remote Control and AA Batteries
•
CD-ROM
•
Setup Manual
•
Thumbscrew for optional stand x 2*2
Video Signal Cable
(Mini D-SUB 15 pin to
Mini D-SUB 15 pin)
Screw (M4 x 10) x 9
Power Cord*1
Thumbscrew for
optional stand x 2*2
Cable cover
Setup Manual
Clamp x 3
CD-ROM
Setup Manual
*
*
Wireless Remote Control
and AA Batteries
Remember to save your original box and packing material to transport or ship the monitor.
1
Type and number of power cords included will depend on the where the LCD monitor is to be shipped. When more than
one power cord is included, please use a power cord that matches the AC voltage of the power outlet and has been
approved by and complies with the safety standard of your particular country.
*2 Installed on the display.
English-4
Downloaded From TV-Manual.com Manuals
This device cannot be used or installed without the Tabletop
Stand or other mounting accessory for support. For proper
installation it is strongly recommended to use a trained,
NEC authorized service person. Failure to follow NEC
standard mounting procedures could result in damage to the
equipment or injury to the user or installer. Product warranty
does not cover damage caused by improper installation.
Failure to follow these recommendations could result in
voiding the warranty.
English
Installation
Orientation
•
When using the display in the portrait position, the
monitor should be rotated clockwise so that the left side
is moved to the top and the LED indicator light is on the
bottom. This will allow for proper ventilation and will
extend the lifetime of the monitor. Improper ventilation
may shorten the lifetime of the monitor.
Mounting
DO NOT mount the monitor yourself. Please ask dealer. For
proper installation it is strongly recommended to use a
trained, qualified technician. Please inspect the location
where the unit is to be mounted. Mounting on wall or ceiling
is the customer’s responsibility. Not all walls or ceilings are
capable of supporting the weight of the unit. Product
warranty does not cover damage caused by improper
installation, remodelling, or natural disasters. Failure to
comply with these recommendations could result in voiding
the warranty.
DO NOT block ventilated openings with mounting
accessories or other accessories.
LED Indicator
For NEC Qualified Personnel:
To insure safe installation, use two or more brackets to
mount the unit. Mount the unit to at least two points on the
installation location.
•
The ceiling and wall must be strong enough to support
the monitor and mounting accessories.
•
DO NOT install in locations where a door or gate can hit
the unit.
•
DO NOT install in areas where the unit will be subjected
to strong vibrations and dust.
•
DO NOT install near where the main power supply
enters the building.
Mounting
Bracket
•
Do not install in where people can easily grab and hang
onto the unit or the mounting apparatus.
Washer
•
When mounting in a recessed area, as in a wall, leave at
least 4 inches (10cm) of space between the monitor and
the wall for proper ventilation.
•
Allow adequate ventilation or provide air conditioning
around the monitor, so that heat can properly dissipate
away from the unit and mounting apparatus.
Please note the following when mounting
on wall or ceiling
•
•
•
•
When using mounting accessories other than those that
are NEC approved, they must comply with the VESAcompatible (FDMlv1) mounting method.
NEC strongly recommends
using size M6 screws
(11-12 mm + thickness of
bracket and washer in
length). If using screws
longer than 11-12 mm,
check the depth of the hole.
(Recommended Fasten
Force: 470 - 635N•cm)
NEC recommends mounting
interfaces that comply with
UL1678 standard in North
America.
Unit
Mounting location
Screw
11-12 mm
Thickness
of bracket
and washer
Screw length should equal
depth of hole (11-12 mm) +
the thickness of mounting
bracket and washer.
Prior to mounting, inspect the installation location to
insure that it is strong enough to support the weight of
the unit so that the unit will be safe from harm.
Refer to the instructions included with the mounting
equipment for detailed information.
Mounting on ceiling
•
Ensure that the ceiling is sturdy enough to support the
weight of the unit and the mounting apparatus over time,
against earthquakes, unexpected vibrations, and other
external forces.
•
Be sure the unit is mounted to a solid structure within the
ceiling, such as a support beam. Secure the monitor
using bolts, spring lock washers, washer and nut.
•
DO NOT mount to areas that have no supporting internal
structure. DO NOT use wood screws or anchor screws
for mounting. DO NOT mount the unit to trim or to
hanging fixtures.
Maintenance
•
Periodically check for loose screws, gaps, distortions, or
other problems that may occur with the mounting
apparatus. If a problem is detected, please refer to
qualified personnel for service.
•
Regularly check the mounting location for signs of
damage or weakness that may occur over time.
English-5
Downloaded From TV-Manual.com Manuals
Attaching Mounting Accessories
3. Ventilation Requirements
The display is designed for use with the VESA mounting
system.
When mounting in an enclosed space or recessed area,
leave adequate room between the monitor and the
enclosure to allow heat to disperse, as shown below.
1. Attach Mounting Accessories
Be careful to avoid tipping monitor when attaching
accessories.
VESA Mounting Interface
Mounting accessories can be attached with the monitor in
the face down position. To avoid damaging the screen face,
place the protective sheet on the table underneath the LCD.
The protective sheet was wrapped around the LCD in the
original packaging. Make sure there is nothing on the table
that can damage the monitor.
When using mounting accessories other than NEC
compliant and approved, they must comply with the VESAcompatible mounting method.
Allow adequate ventilation or provide air conditioning around
the monitor, so that heat can properly dissipate away from
the unit and mounting apparatus; especially when you use
monitors in multiple screen.
4. Prevent Tipping
When using the display with the optional table top stand
fasten the LCD to a wall using a cord or chain that can
support the weight of the monitor in order to prevent the
monitor from falling. Fasten the cord or chain to the monitor
using the provided clamps and screws.
278 mm (P401)
304 mm (P461)
400 mm (P521)
2. Installing and removing optional table
top stand
Screw Holes
CAUTION: Installing and removing the stand must be done
by two or more people (P401/P461), by four or
more people (P521).
To install, follow those instructions included with the stand or
mounting apparatus. Use only those devices recommended
by the manufacturer.
NOTE: Before using optional table top stand, remove
installed thumbscrews from the display first.
Use ONLY thumbscrews which are installed
on the display.
Cord or chain
Clamp
Screw
Before attaching the LCD monitor to the wall, make sure
that the wall can support the weight of the monitor.
Handle with care when mounting LCD monitor stand and
avoid pinching your fingers.
Optional table top stand
Be sure to remove the cord or chain from the wall before
moving the LCD.
Table
Protective Sheet
NOTE: Place stand onto monitor so that the long end of the
feet are in the front.
English-6
Downloaded From TV-Manual.com Manuals
English
Parts Name and Functions
Control Panel
POWER button
EXIT button
Switches the power on/off. See also page 16.
Activates the OSD menu when the OSD menu is turned-off.
Acts as EXIT button within the OSD to move to previous
menu.
MUTE button
Switches the audio mute ON/OFF.
Remote control sensor and Power Indicator
INPUT button
Acts as SET button within OSD menu. (Toggle switches
between [DVI], [DPORT], [VGA], [RGB/HV], [HDMI],
[DVD/HD1], [DVD/HD2], [SCART], [VIDEO1], [VIDEO2],
[S-VIDEO] or [TV]*). These are available input only,
shown as their factory preset name.
PLUS button
Acts as (+) button to increase the adjustment with OSD menu.
Increases the audio output level when the OSD menu is
turned off.
Receives the signal from the remote control (when using the
wireless remote control). See also page 11.
Glows green when the LCD monitor is in active mode*.
Glows red when the LCD is in POWER OFF (ECO standby)
mode. Glows amber when the LCD is in POWER OFF
(standby) mode. Blinks amber when the monitor is in Power
Save Mode. Green and Amber blink alternately while in
Power Standby mode with the “SCHEDULE SETTINGS”
function enabled. When a component failure is detected
within the monitor, the indicator will blink red.
* If “OFF” is selected in “POWER INDICATOR” (see page 23),
LED will not light when the LCD monitor is in active mode.
AMBIENT LIGHT SENSOR
MINUS button
Acts as (-) button to decrease the adjustment with OSD menu.
Decreases the audio output level when the OSD menu is
turned off.
UP button
Detects the level of ambient light, allowing the monitor to
make automatic adjustments to the brightness setting,
resulting in a more comfortable viewing experience. Do not
cover this sensor. See page 18.
Control Key Lock Mode
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area up to select
adjustment items within OSD menu.
DOWN button
Activates the OSD menu when the OSD menu is turned-off.
Acts as button to move the highlighted area down to
select adjustment items within OSD menu.
This control completely locks out access to all Control Key
functions. To activate the control key lock function, press both
and and hold down simultaneously for more than
3 seconds. To resume user mode, press both and and
hold simultaneously for more than 3 seconds.
*: The product you purchased may not have this feature.
English-7
Downloaded From TV-Manual.com Manuals
Terminal Panel
In
Out
In
Main Power Switch
Out
VIDEO IN connector (BNC and RCA)
On/Off switch to turn main power ON/OFF.
To input a composite video signal. BNC and RCA connectors
are not available at the same time (Use only one input).
AC IN connector
VIDEO OUT connector (BNC)
Connects with the supplied power cord.
To output the composite video signal from the VIDEO IN
connector.
DISPLAYPORT connector
To input DisplayPort signals.
DVD/HD connector (RCA)
HDMI connector
Connecting equipment such as a DVD player, HDTV device,
or Set-Top-Box.
To input digital HDMI signals.
S-VIDEO IN connector (Mini DIN 4 pin)
DVI IN (DVI-D)
To input digital RGB signals from a computer or HDTV
device having a digital RGB output.
To input the S-video (Y/C separate signal).
* This connector does not support analog input.
To input audio signal from external equipment such as a
computer, VCR or DVD player.
AUDIO IN 1, 2, 3
VGA IN (mini D-Sub 15 pin)
AUDIO OUT
To input analog RGB signals from a personal computer or
from other RGB equipment.
To output the audio signal from the AUDIO IN 1, 2, 3,
DPORT, HDMI, and TV jack to an external device
(stereo receiver, amplifier, etc.).
RGB/HV IN [R, G, B, H, V] (BNC)
To input analog RGB signals or signals from other RGB
equipment.
This is also to connect equipment such as a DVD player,
HDTV device and Set-Top-Box. A Sync-on-Green signal can
be connected to the G connector.
This input can be used with an RGB, DVD/HD or Video
source. Please select signal type in TERMINAL SETTING.
RGB/HV
DVD/HD2
VIDEO2
R
G
B
H
V
R
G
B
H
V
Pr
Y
Pb
EXTERNAL CONTROL (D-Sub 9 pin)
IN connector: Connect RS-232C input from external
equipment such as a PC in order to control RS-232C
functions.
OUT connector: Connect RS-232C output. To connect
multiple MultiSync monitors via RS-232C daisy Chain.
LAN port (RJ-45)
LAN connection. See page 30.
VIDEO
REMOTE IN/OUT
RGB/HV OUT (BNC)
To output the signal from the RGB/HV IN connector or
VGA IN connector which is on screen to an input on a
separate device. If both signals are not on screen, outputs
the signal from RGB/HV IN connector.
Use the optional wired remote control by connecting it to
your monitor.
NOTE: When you use Remote IN/OUT, IR CONTROL in
OSD menu should be NORMAL.
English-8
Downloaded From TV-Manual.com Manuals
English
Kensington Lock
For security and theft prevention.
EXTERNAL SPEAKER TERMINAL
To output the audio signal from AUDIO 1, 2, 3, DPORT,
HDMI and TV jack.
Note: This speaker terminal is for 15W + 15W (8 ohm)
speaker.
Option board slot
Slot for board accessories. Please contact your supplier for
detailed information.
English-9
Downloaded From TV-Manual.com Manuals
Wireless Remote Control
SOUND button
Artificial surround sound.
KEYPAD
Press buttons to set and change passwords, change
channel and set REMOTE ID.
ENT button*
DISPLAY button
Turns on/off the information OSD. See page 18.
MENU button
Turns on/off the menu mode.
AUTO SETUP button
Enters auto setup menu. See page 20.
EXIT button
Returns to previous menu within OSD menu.
UP/DOWN button
button to move the highlighted area up or
Acts as
down to select adjustment items within OSD menu.
Small screen which adjusted “PIP” mode moves up or down.
MINUS/PLUS (-/+) button
Increases or decreases the adjustment level within OSD
menu settings.
Small screen which adjusted “PIP” mode moves left or right.
SET button
POWER button
Makes selection.
Switches the power on/standby.
VOLUME UP/DOWN button
INPUT button
Increases or decreases audio output level.
Selects input signal.
DVI: DVI
DISPLAYPORT: DPORT
VGA: VGA
RGB/HV: RGB/HV
HDMI: HDMI
DVD/HD: DVD/HD1, DVD/HD2, SCART
VIDEO: VIDEO1, VIDEO2
S-VIDEO: S-VIDEO
OPTION: Depends on your connection
CH UP/DOWN button*
GUIDE button*
MUTE button
Turns on/off mute function.
STILL button
ON/OFF button: Activates/deactivates still picture mode.
STILL CAPTURE button: Captures still picture.
PICTURE MODE button
PIP (Picture In Picture) button
Selects picture mode, [HIGHBRIGHT], [STANDARD],
[sRGB], [CINEMA], [AMBIENT1], [AMBIENT2]. See page 18.
ASPECT button
Selects picture aspect, [FULL], [NORMAL], [WIDE] and
[ZOOM]. See page 17.
Sub picture
Main picture
HIGHBRIGHT: for moving images such as DVD.
STANDARD: for images.
sRGB: for text based images.
CINEMA: for movies.
AMBIENT1 and AMBIENT2: activate auto dimming
function. See page 18.
ON/OFF button: Toggle switches between PIP, POP, sideby-side (aspect) and side-by-side (full). See page 22.
INPUT button: Selects the “picture in picture” input signal.
CHANGE button: Replaces to the main picture and sub
picture.
DVI DPORT VGA RGB/HV HDMI DVD/HD1 DVD/HD2 SCART VIDEO1 VIDEO2 S-VIDEO
DVI
DPORT
VGA
RGB/HV
HDMI
DVD/HD1
DVD/HD2
SCART
VIDEO1
VIDEO2
S-VIDEO
-
English-10
Downloaded From TV-Manual.com Manuals
MTS button*
AUDIO INPUT button
Selects audio input source [IN1], [IN2], [IN3], [HDMI],
[DPORT], [TV]*1, [OPTION]*1.
Operating Range for the Remote
Control
Point the top of the remote control toward the LCD monitor’s
remote sensor during button operation.
Use the remote control within a distance of about 7 m (23 ft.)
from remote control sensor or at a horizontal and vertical
angle of within 30° within a distance of about 3.5 m (10 ft.).
button
Activates closed captioning.
Note: VIDEO1, VIDEO2, S-VIDEO inputs only.
*: This button’s action depends on which option board you use.
Refer to the option board’s manual for further information.
*1: The product you purchased may not have this feature.
Caution: Important, the remote control
system may not function when
direct sunlight or strong
illumination strikes the remote
control sensor or when there is
an object in the path.
Handling the remote control
•
Do not subject to strong shock.
•
Do not allow water or other liquid to splash the remote
control. If the remote control gets wet, wipe it dry
immediately.
•
Avoid exposure to heat and steam.
•
Other than to install the batteries, do not open the
remote control.
English-11
Downloaded From TV-Manual.com Manuals
English
REMOTE ID button
Activates REMOTE ID function.
Setup
1. Determine the installation location
NEC recommends the following battery use:
CAUTION: Installing your LCD display must be done by a
qualified technician. Contact your dealer for
more information.
•
Place “AA” size batteries matching the (+) and (-) signs
on each battery to the (+) and (-) signs of the battery
compartment.
•
Do not mix battery brands.
•
Do not combine new and old batteries. This can shorten
battery life or cause liquid leakage of batteries.
•
Remove dead batteries immediately to prevent battery
acid from leaking into the battery compartment.
•
Do not touch exposed battery acid, it may injure skin.
CAUTION: MOVING OR INSTALLING THE LCD MONITOR
MUST BE DONE BY TWO OR MORE PEOPLE
(P401/P461), BY FOUR OR MORE PEOPLE
(P521). Failure to follow this caution may result in
injury if the LCD monitor falls.
CAUTION: Do not mount or operate the display upside
down, face up, or face down.
NOTE: If you do not intend to use the Remote Control for a
long period of time, remove the batteries.
CAUTION: This LCD has a temperature sensor and cooling
fan. If the LCD becomes too hot, the cooling fan
will turn on automatically. If the LCD becomes
overheated while the cooling fan is running, a
“Caution” warning will appear. If the “Caution”
warning appears, discontinue use and allow the
unit to cool. Using the cooling fan will reduce the
likelihood of early circuit failure and may help
reduce image degradation and “Image
Persistance”.
If the LCD is used in an enclosed area or if the
LCD panel is covered with a protective screen,
please check the inside temperature of the
monitor by using the “HEAT STATUS” control in
the OSD (see page 24). If the temperature is
higher than the normal operating temperature,
please turn the cooling fan to ON within the FAN
CONTROL menu within the OSD (see page 24).
IMPORTANT: Lay the protective sheet, which was wrapped
around the LCD monitor when it was
packaged, beneath the LCD monitor so as
not to scratch the panel.
3. Connect external equipment
(See pages 14 and 15)
•
To protect the external equipment; turn off the main
power before making connections.
•
Refer to your equipment user manual for further
information.
NOTE: Do not connect/disconnect cables when turning on
the monitor or other external equipment as this may
result in a loss of the monitor image.
4. Connect the supplied power cord
•
The equipment should be installed close to an easily
accessible power outlet.
•
Please fasten power cord to the LCD monitor by
attaching the screw and clamp.
•
Fully insert the prongs into the power outlet socket.
A loose connection may cause image degradation.
NOTE: Please refer to the “Safety Precautions and
Maintenance” section of this manual for proper
selection of AC power cord.
Screw
2. Install the remote control batteries
The remote control is powered by two 1.5V AA batteries.
To install or replace batteries:
A. Press and slide to open the cover.
B. Align the batteries according to the (+) and (–)
indications inside the case.
C. Replace the cover.
CAUTION: Incorrect usage of batteries can result in leaks
or bursting.
English-12
Downloaded From TV-Manual.com Manuals
Clamp
•
English
5. Attach the cable cover
Use six of the M4 x 10 screws (included) to attach the
cable cover.
6. Switch on the power of all the attached
external equipment
When connected with a computer, switch on the power of
the computer first.
7. Operate the attached external
equipment
Display the signal from the desired input source.
8. Adjust the sound
Make volume adjustments when required.
9. Adjust the screen (See pages 20 and 21)
Make adjustments of the screen display position when
necessary.
10. Adjust the image (See page 20)
Make adjustments such as brightness or contrast when
required.
11. Recommended Adjustments
To reduce the risk of the “Image Persistence”, please adjust
the following items based on the application being used:
“SCREEN SAVER”, “SIDE BORDER COLOR” (See page 24)
“DATE & TIME”, “SCHEDULE SETTINGS” (See page 21).
It is recommended that the “FAN CONTROL” setting
(See page 24) be turned to ON also.
English-13
Downloaded From TV-Manual.com Manuals
Connections
NOTE: Do not connect/disconnect cables when turning on the monitor or other external equipment as this may result in a
loss of the monitor image.
NOTE: Use an audio cable without a built-in resistor. Using an audio cable with a built-in resistor turns down the sound.
Before making connections:
*
First turn off the power of all the attached equipment and make connections.
*
Refer to the user manual included with each separate piece of equipment.
Wiring Diagram
DVD player
with HDMI out
DVD player
Stereo Amplifier
VCR or DVD
Player
Computer (Analog)
Second monitor*
DVD player with
SCART OUT
Computer (Digital)
*: Multiple monitors that are daisy-chained have a limit to the connectable monitors.
Connected
equipment
AV
PC
Connecting
Setting in Terminal Mode
terminal
DVD/HD1 (3RCA)
DVI (DVI-D)
DVI MODE: DVI-HD
HDMI
RAW/EXPAND*1
DVD/HD+VIDEO
SCART: ON
VIDEO1 (BNC&RCA)
S-VIDEO
VIDEO2 (5BNC)
BNC MODE: VIDEO
DVD/HD2 (5BNC)
BNC MODE: COMPONENT
VGA (D-Sub)
DVI (DVI-D)
DVI MODE: DVI-PC
RGB/HV (5BNC)
BNC MODE: RGB
DisplayPort
-
Input signal
name
DVD/HD1
DVI
HDMI
SCART
VIDEO1
S-VIDEO
VIDEO2
DVD/HD2
VGA
DVI
RGB/HV
DPORT
Connecting
Audio terminal
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
HDMI
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
AUDIO IN1, IN2, IN3
DPORT
Input button
in remote control
DVD/HD
DVI
HDMI
DVD/HD
VIDEO
S-VIDEO
VIDEO
DVD/HD
VGA
DVI
RGB/HV
DISPLAYPORT
*1: depend on signal type.
•
AUDIO IN 1, 2 and 3 can be used for audio input. To select audio source [IN1], [IN2] or [IN3] in AUDIO INPUT in OSD
menu or press the AUDIO INPUT button (remote control).
English-14
Downloaded From TV-Manual.com Manuals
Connecting your computer to your LCD monitor will enable you to display your computer’s screen image.
Some video cards with a pixel clock over 162MHz may not display an image correctly.
Your LCD monitor displays proper image by adjusting the factory preset timing signal automatically.
<Factory preset signal timing>
Resolution
640 x 480
800 x 600
1024 x 768
1280 x 768
1360 x 768
1280 x 1024
1600 x 1200
1920 x 1080
•
Scanning frequency
Horizontal
Vertical
31.5kHz
60Hz
37.9kHz
60Hz
48.4kHz
60Hz
48kHz
60Hz
48kHz
60Hz
64kHz
60Hz
75kHz
60Hz
66.6kHz
60Hz
Remarks
Compressed image
Recommended resolution
If you use with a Macintosh PowerBook, set “Mirroring” to Off on your PowerBook.
Refer to your Macintosh’s owner’s manual for more information about your computer’s video output requirements and any
special identification or configuration your monitor’s image and monitor may require.
•
Input TMDS signals conforming to DVI standards.
•
To maintain display quality, use a cable that conforms to DVI standards.
Connecting a DVD Player with HDMI out
•
Please use an HDMI cable with HDMI logo.
•
It may take a moment for the signal to appear.
•
PC-DVI signals are not supported.
Connecting a Computer with DisplayPort
•
Please use DisplayPort cable with DisplayPort certified logo.
•
It may take a moment for the signal to appear.
•
Please note that DisplayPort connector does not supply power to the connected component.
•
Please note that when connecting a DisplayPort cable to a component with a signal conversion adapter, an image may not
appear.
•
Select DisplayPort cables feature a locking function. When removing this cable, hold down the top button to release the
lock.
English-15
Downloaded From TV-Manual.com Manuals
English
Connecting a Personal Computer
Basic Operation
Power ON and OFF Modes
The LCD monitor power indicator will turn green while powered on and will turn red or amber while powered off.
NOTE: The Main Power Switch must be in the ON position in order to power up the monitor using the remote control or the
Power Button on the front of the LCD.
OFF
Main Power Switch
ON
Power Button
Using the remote control
English-16
Downloaded From TV-Manual.com Manuals
Mode
Power ON
Power OFF (Eco Standby)*1
Power consumption under 0.5W*3
Power OFF (Standby)
Power consumption under 1W*3, *4
Power Save
Power consumption under 2W*3, *5
Power Standby when
“SCHEDULE SETTINGS” enabled
Diagnosis (Detecting failure)
Picture Aspect
DVI, VGA, RGB/HV, DPORT
Status Indicator Light
Green*2
Red
FULL
ZOOM
NORMAL
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV*
Amber
FULL
Amber Blinking
Green and Amber blink alternately
WIDE
Aspect ratio
of image
NORMAL
Unchanged view*6
Red Blinking
(See Troubleshooting page 34)
*1 When in Eco Standby Mode DDC/CI control does not function.
*2 If “OFF” is selected in POWER INDICATOR (page 23), the LED will not light when
the LCD monitor is in active mode.
*3 “RS-232C” is selected in EXTERNAL CONTROL.
*4 DDC/CI should be disabled.
*5 No DisplayPort connection.
ZOOM
4:3
Recommended selection
for picture aspect*6
NORMAL
ZOOM
(DYNAMIC)
FULL
Using Power Management
Squeeze
The LCD monitor follows the VESA approved DPM Display
Power Management function.
The power management function is an energy saving
function that automatically reduces the power consumption
of the display when the keyboard or the mouse has not been
used for a fixed period.
The power management feature on your new display has
been set to the “ON” mode. This allows your display to enter
a Power Saving Mode when no signal is applied. This could
potentially increase the life and decrease the power
consumption of the display.
NOTE: Depending on the PC and video card used, this
function may not operate.
WIDE
Letterbox
*6 Grey areas indicate unused portions of the screen.
NORMAL: Displays the aspect ratio the same as it is sent
from the source.
FULL: Fills entire screen.
WIDE: Expands a 16:9 letter box signal to fill entire screen.
ZOOM (DYNAMIC): Expands a 4:3 pictures to fill the entire
screen with non-linearity. Some of the outside image area
will be cut off due to expansion.
ZOOM
The image can be expanded beyond the active display area.
The image which is outside of active display area is not
shown.
Selecting a video source
To view a video source:
Use the input button to set [VIDEO1], [VIDEO2], [S-VIDEO].
ZOOM
Use the COLOR SYSTEM menu to set [AUTO], [NTSC],
[PAL], [SECAM], [PAL60], [4.43NTSC], according to your
video format.
ZOOM
*: The product you purchased may not have this feature.
English-17
Downloaded From TV-Manual.com Manuals
English
Power Indicator
Information OSD
The Information OSD provides information such as: Monitor ID, Input Source, Picture Size, etc.
Press the DISPLAY button on the remote to bring up the Information OSD.
ID number assigned to current monitor*7
ID number assigned monitor to be controlled via RS-232C*8
Input Name
Audio input mode
Picture aspect
Input Signal Information
Sub picture information
*7: “IR CONTROL” should be set “Primary” or “Secondary”.
*8: “IR CONTROL” should be set “Primary”.
Picture Mode
DVI, VGA, RGB/HV, DPORT
STANDARD
sRGB
AMBIENT1
AMBIENT2
HIGHBRIGHT
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV*
STANDARD
CINEMA
AMBIENT1
AMBIENT2
HIGHBRIGHT
AMBIENT Mode
The brightness of the LCD screen can be set to increase or decrease depending on the amount of ambient light within the
room. If the room is bright, the monitor becomes correspondingly bright. If the room is dim, then the monitor will dim
accordingly. The purpose of this function is to make the viewing experience more comfortable to the eye in a variety of lighting
conditions.
NOTE: When picture mode is set to AMBIENT1 or AMBIENT2, BRIGHTNESS, AUTO BRIGHTNESS and BRIGHTNESS in
SCREEN SAVER function are disabled.
Do not cover Ambient light sensor when you use AMBIENT1 or AMBIENT2 in PICTURE MODE.
AMBIENT parameter setting
PICTURE MODE in OSD, select AMBIENT1 or AMBIENT2 and set IN BRIGHT and IN DARK in each mode.
IN BRIGHT: This is the brightness level that the monitor will go up to when the ambient light level is highest.
IN DARK: This is the level of brightness that the monitor will go down to when the ambient light level is low.
When the AMBIENT function is enabled the Brightness level of the screen changes automatically according to the lighting
conditions of the room (Figure 1).
Factory Setting
BRIGHTNESS range
BRIGHTNESS level set
for the monitor to use
when ambient lighting
level is low.
BRIGHTNESS level set for the
monitor to use when ambient
lighting level is high.
IN DARK
dark
IN BRIGHT
room bright condition
bright
Screen Brightness value by AMBIENT1 mode
Screen Brightness value by AMBIENT2 mode
Figure 1
IN DARK: BRIGHTNESS level set for the monitor to use when ambient lighting level is low.
IN BRIGHT: BRIGHTNESS level set for the monitor to use when ambient lighting level is high.
*: The product you purchased may not have this feature.
English-18
Downloaded From TV-Manual.com Manuals
English
OSD (On-Screen-Display) Controls
NOTE: Some functions may not be available depending on the model or optional equipment.
Input source
Main Menu Icons
Main Menu Item
70
50
50
50
50
50
Sub Menu
THANK YOU FOR SAVING
THE ENVIRONMENT.
CARBON FOOTPRINT
86.0 %
PICTURE MODE
Select
Adjustment Settings
Goto Adjustment
Return
Close
Key Guide
Press UP or DOWN
button to select
sub-menu.
Press SET.
Press UP or DOWN,
PLUS or MINUS to select
the function or setting to
be adjusted.
Press MENU or EXIT.
Press UP or DOWN
button to select.
Press INPUT button
to decide.
Press UP or DOWN, PLUS
or MINUS button to select.
Press EXIT
Remote Control
Control Panel
OSD screen
English-19
Downloaded From TV-Manual.com Manuals
Setting
Default
PICTURE
BRIGHTNESS
Adjusts the overall image and background brightness. Press + or - to adjust.
Note: When AMBIENT1 or AMBIENT2 is selected in picture mode, this function cannot changed.
70
CONTRAST
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
50
SHARPNESS
Adjusts the crispness of the image. Press + or - to adjust.
BLACK LEVEL
Adjusts the image brightness in relationship to the background. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
50
TINT
Adjusts the tint of the screen. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
50
COLOR
Adjusts the color depth of the screen. Press + or - to adjust.
Note: The sRGB picture mode is standard and cannot be changed.
50*2
COLOR TEMPERATURE
Adjusts the color temperature of the entire screen. A low color temperature will make the screen
reddish. A high color temperature will make the screen bluish. If TEMPERATURE needs further
adjustment, the individual R/G/B/ levels of the white point can be adjusted. To adjust the
R/G/B levels, CUSTOM must be showing as the COLOR TEMP selection.
Note: The sRGB picture mode is set to a predefined 6500 K standard and cannot be changed.
When PROGRAMMABLE is selected in GAMMA SELECTION, this function cannot be changed.
COLOR CONTROL
Adjusts the levels of the Red, Yellow, Green, Cyan, Blue, Magenta and Saturation.
Note: The sRGB picture mode is standard and cannot be changed.
GAMMA SELECTION
Select a display gamma for best picture quality.
Note: The sRGB picture mode is standard and cannot be changed.
50*2
10000K
0
NATIVE*2
(except sRGB
setting)
NATIVE
Gamma correction is handled by the LCD panel.
2.2
Typical display gamma for use with a PC.
2.4
Good for video (TV, DVD, etc.)
S GAMMA
Special gamma for certain types of movies. Raises the dark parts and lowers the light parts
of the image (S-Curve).
DICOM SIM.
DICOM GSDF curve simulated for LCD type.
PROGRAMMABLE
A programmable gamma curve can be loaded using NEC optional software.
MOVIE SETTINGS
NOISE REDUCTION
6*2
Adjusts the amount of noise reduction. Press + or - to adjust.
TV, VIDEO1, VIDEO2, S-VIDEO inputs only
FILM MODE
AUTO*2
Automatically senses the sources frame rate for optimal picture quality.
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
ADAPTIVE CONTRAST Sets the level of adjustment for dynamic contrast.
OFF
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
PICTURE MODE
Selects picture mode, [HIGHBRIGHT], [STANDARD], [sRGB], [CINEMA], [AMBIENT1] or
[AMBIENT2]. See page 18.
STANDARD
PICTURE RESET
Resets the following settings within the PICTURE menu back to factory setting:
BRIGHTNESS, CONTRAST, SHARPNESS, BLACK LEVEL, TINT, COLOR, COLOR
TEMPERATURE, COLOR CONTROL , GAMMA SELECTION, MOVIE SETTINGS.
-
Automatically adjusts Screen Size, H position, V position, Clock, Clock Phase and White Level.
-
ADJUST
AUTO SETUP
VGA, RGB/HV inputs only
AUTO ADJUST
H Position, V Position and Clock Phase are adjusted automatically upon power on.
OFF
VGA, RGB/HV inputs only
H POSITION
Controls the horizontal position of the image within the Display area of the LCD.
Press + to move right. Press - to move left.
-
Controls the vertical position of the image within the Display area of the LCD.
Press + to move up. Press - to move down.
-
Press + to expand the width of the image on the right of the screen.
Press - to narrow the width of the image on the left.
-
VGA, RGB/HV inputs only
CLOCK PHASE
Adjusts the visual “noise” on the image.
-
All inputs except DVI, HDMI, DPORT
V POSITION
All inputs except DVI, HDMI, DPORT
CLOCK
VGA, RGB/HV, DVD/HD1, DVD/HD2, SCART inputs only
*: The product you purchased may not have this feature.
*2: depends on signal input
English-20
Downloaded From TV-Manual.com Manuals
Adjusts the horizontal size of the image.
-
Adjusts the vertical size of the image.
-
VGA, RGB/HV inputs only
V RESOLUTION
VGA, RGB/HV inputs only
INPUT RESOLUTION
VGA, RGB/HV inputs only
If there is a problem with signal detection, this function forces the monitor to display the
signal at the desired resolution. After selection, execute “AUTO SETUP” if required.
If no problem is detected, the only available option will be “AUTO”.
ZOOM MODE
Select the aspect ratio of the screen image.
AUTO
-
All inputs except TV*
BASE ZOOM
16:9
CUSTOM
For input sources that have a 16:9 aspect ratio.
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
14:9
For input sources that have a 14:9 aspect ratio.
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
DYNAMIC
Expands 4:3 picture to fill the screen. Some of the image is lost due to expansion.
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO inputs only
OFF
All inputs, except TV*
Selecting “OFF” will display the image in a 1 by 1 pixel format. (If the input resolution is
higher than a 1920 x 1080 resolution, the image will be scaled down to fit the screen.)
CUSTOM
Displays an image as large as possible without changing the aspect ration.
All inputs, except TV*
ZOOM**
Maintains the aspect ratio while zooming.
1.00
H ZOOM**
Amount of horizontal zoom. Can be adjusted for each BASE ZOOM setting.
1.00
V ZOOM**
Amount of vertical zoom. Can be adjusted for each BASE ZOOM setting.
1.00
H POS**
Horizontal position. Can be adjusted for each BASE ZOOM setting.
0%
V POS**
Vertical position. Can be adjusted for each BASE ZOOM setting.
0%
ASPECT
Selects picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17.
FULL
ADJUST RESET
Resets the following settings within the ADJUST menu back to factory setting:
AUTO ADJUST, H POSITION, V POSITION, CLOCK, CLOCK PHASE, H RESOLUTION,
V RESOLUTION, ZOOM MODE, ASPECT.
-
AUDIO
BALANCE
CENTER
TREBLE
0
BASS
0
PIP AUDIO
Selects source of PIP audio.
MAIN AUDIO
LINE OUT
Selecting “VARIABLE” will enable to control line out level with VOLUME button.
SURROUND
Artificial surround sound.
AUDIO INPUT
Selects audio input source [IN1], [IN2], [IN3], [DPORT], [HDMI], [TV]*, [OPTION]*.
AUDIO RESET
Resets “AUDIO” options back to factory settings.
FIXED
OFF
Depend on signal input
-
SCHEDULE
OFF TIMER
Sets the monitor to power off after a length of time.
A time between 1 to 24 hours is available.
OFF
SCHEDULE SETTINGS
Creates a working schedule for the monitor to use.
-
SCHEDULE LIST
List of schedules.
-
DATE & TIME
Sets the date, time, and daylight saving region. Date & time must be set in order for the
“SCHEDULE” function to operate. See page 26.
YEAR
-
MONTH
-
DAY
-
TIME
-
DAYLIGHT SAVING
OFF
*: The product you purchased may not have this feature.
**: 16:9, 14:9, CUSTOM only
English-21
Downloaded From TV-Manual.com Manuals
English
H RESOLUTION
SCHEDULE RESET
Resets the following settings within the SCHEDULE menu back to factory setting:
OFF TIMER, SCHEDULE SETTINGS.
-
PIP
KEEP PIP MODE
Allows the monitor to remain in “PIP” and “TEXT TICKER” mode after powering off.
When Power is returned, PIP and TEXT TICKER appear without having to enter the OSD.
OFF
PIP MODE
Picture-in-Picture
OFF
OFF
OFF
PIP
PIP
POP
POP
SIDE BY SIDE (ASPECT) SIDE BY SIDE ASPECT
SIDE BY SIDE (FULL)
PIP SIZE
SIDE BY SIDE FULL
Selects the size of the sub-picture used in Picture-in-Picture (PIP) mode.
LARGE
SMALL
MIDDLE
LARGE
PIP POSITION
Determines where the PIP appears on the screen.
ASPECT
Selects sub picture aspect, [FULL], [NORMAL], [WIDE] and [ZOOM]. See page 17.
TEXT TICKER
X = 95, Y = 92
FULL
OFF
MODE
Enables Text Ticker and allows you to set Horizontal or Vertical direction.
POSITION
Selects the location of the Text Ticker on the screen.
SIZE
Determines the size of the Text Ticker in relationship to the overall screen size.
BLEND
Sets the transparency of the Text Ticker (0: transparent, 100: opaque).
DETECT
Enables auto-detection of the Text Ticker.
FADE IN
Enables fade-in of the text ticker.
SUB INPUT
Selects sub picture input signal.
PIP RESET
Resets PIP options back to factory settings except ASPECT and SUB INPUT.
Depend on signal input
-
OSD
LANGUAGE
Select the language used by the OSD.
ENGLISH
ENGLISH
(Depend on
destination)
DEUTSCH
FRANÇAIS
ITALIANO
ESPAÑOL
SVENSKA
РУССКИЙ
OSD TURN OFF
Turns off the OSD after a period of inactivity. The preset choices are 10-240 seconds.
OSD POSITION
Determines the location where the OSD appears on the screen.
30 Sec.
X = 128, Y = 225
UP
DOWN
LEFT
RIGHT
INFORMATION OSD
Selects whether the information OSD is displayed or not. The information OSD will be
displayed when the input signal or source changes. The information OSD will also give a
warning when there is no-signal or the signal is out-of range.
An interval between 3 to 10 seconds for the Information OSD to appear is available.
English-22
Downloaded From TV-Manual.com Manuals
ON, 3 Sec.
OSD TRANSPARENCY
Set the transparency level of the OSD.
-
TYPE2
OFF
TYPE1
TYPE2
OSD ROTATION
Determines the OSD display direction between landscape and portrait.
LANDSCAPE
Display the OSD with landscape mode.
PORTRAIT
Display the OSD with portrait mode.
INPUT NAME
You can set currently displayed INPUT name as you like.
Max: 8 characters, including Space, A-Z, 0-9, and some symbols.
CLOSED CAPTION
Activates closed captioning.
LANDSCAPE
-
OFF
VIDEO1, VIDEO2, S-VIDEO inputs only
OSD RESET
Resets the following settings within the OSD menu back to factory setting:
OSD TURN OFF, OSD POSITION, INFORMATION OSD, OSD TRANSPARENCY,
CLOSED CAPTION.
-
MONITOR ID
Sets the monitor ID number from 1-100 and group ID from A-J.
NOTE: Group ID is made of multiple selections.
1
IR CONTROL
Selects the mode of the monitor for use with the infra-red remote control when using the
RS-232C daisy chain.
MULTI DISPLAY
NORMAL
The monitor will be controlled normally by wireless remote controller.
PRIMARY
Choose “PRIMARY” for the first monitor within an RS-232C daisy chain.
SECONDARY
Choose “SECONDARY” for all subsequent monitors within an RS-232C daisy chain.
LOCK
Prevents the monitor from being controlled by wireless remote controller. To return to normal
operation, press the “DISPLAY” button on the remote controller for 5 seconds.
TILE MATRIX
NORMAL
Allows one image to be expanded and displayed over multiple screens (up to 100) through a
distribution amplifier.
NOTE: Low resolution is not suitable for tiling to a large number of monitors. You can operate
without a distribution amplifier at the lower number of screens.
H MONITORS
Number of monitors arranged horizontally.
1
V MONITORS
Number of monitors arranged vertically.
1
POSITION
Select which section of the tiled image to be displayed on the monitor.
1
TILE COMP
Turns the TILE COMP feature on.
NO
ENABLE
Enables Tile Matrix.
NO
POWER ON DELAY
Adjusts the delay time between being in “standby” mode and entering “power on” mode.
“POWER ON DELAY” can be set between 0 and 50 seconds.
POWER INDICATOR
Turns ON or OFF the LED located at the front of the monitor.
If “OFF” is selected, LED will not light when the LCD monitor is in active mode.
EXTERNAL CONTROL
Selects the control interface, RS-232C or LAN.
LAN RESET
Resets the LAN settings.
In daisy chain condition, set the OSD menu categories which copy from current monitor to
others. NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C”.
This function resets to default when power is off. This function has a limit depending on the
cable you use.
COPY START
Select “YES” and press SET button to start copy.
ALL INPUT
When you check this item, copy to all input teminals. Default is off.
MULTI DISPLAY RESET
ON
RS-232C
CONTROL
SETTING COPY
0 Sec.
Resets “MULTI DISPLAY” options back to factory settings.
English-23
Downloaded From TV-Manual.com Manuals
NO
-
English
MONITOR INFORMATION Monitor Information.
CARBON SAVINGS: Display the estimated carbon saving information in kg. The carbon
footprint factor in the carbon saving calculation is based on the OECD (2008 Edition).
DISPLAY PROTECTION
POWER SAVE
All inputs except for TV*
Sets how long the monitor waits to go into power save mode after a lost signal.
Note: When connecting DVI, video card might not stop sending digital data even if image has
disappeared. In this case the monitor does not get to power management mode.
ON
STANDBY MODE
Lowers power consumption.
Note: When in ECO STANDBY mode, DDC/CI does not function.
ECO
STANDBY
HEAT STATUS
Displays status of the FAN, BRIGHTNESS and TEMPERATURE.
-
FAN CONTROL
Cooling fan reduces the temperature of the display to protect from overheating.
If “AUTO” is selected, you can adjust the start temperature of the cooling fan and fan speed.
SCREEN SAVER
Use the SCREEN SAVER function to reduce the risk of Image Persistence.
AUTO
GAMMA
The display gamma is changed and fixed when “ON” is selected.
OFF
BRIGHTNESS
The brightness is decreased when “ON” is selected.
NOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2.
OFF
MOTION
The screen image is slightly expanded and moves in 4 directions (UP, DOWN, RIGHT, LEFT)
at user determined intervals. You can set interval time and zooming ratio.
This function is disabled when PIP, STILL, TEXT TICKER and TILE MATRIX are enabled.
OFF
SIDE BORDER COLOR
Adjusts the color of the side borders when a 4:3 image is displayed.
Press + button, the bar will become lighter.
Press - button, the bar will become darker.
AUTO BRIGHTNESS
DPORT, DVI, VGA, RGB/HV inputs only
Adjusts the brightness level according to the input signal.
NOTE: Do not select this function when picture model is AMBIENT1 or AMBIENT2.
CHANGE SECURITY
PASSWORD
Allows the security password to be changed.
The factory preset password is 0000.
SECURITY LOCK
Locks the security password.
DDC/CI
ENABLE/DISABLE: Turns On or OFF the two way communication and control of the monitor.
DISPLAY PROTECTION
RESET
Resets the following settings within the DISPLAY PROTECTION menu back to factory setting:
POWER SAVE, STANDBY MODE, FAN CONTROL, SCREEN SAVER, SIDE BORDER COLOR,
AUTO BRIGHTNESS, DDC/CI.
15
OFF
OFF
ENABLE
-
ADVANCED OPTION
INPUT DETECT
All inputs except for TV*
Selects the method of input detection the monitor uses when more than two input devices
are connected.
NONE
The Monitor will not search the other video input ports.
FIRST DETECT
When the current video input signal is not present, then the monitor searches for a video signal
from the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
The monitor will not look for other video signals while the current video source is present.
LAST DETECT
When the monitor is displaying a signal from the current source and a new secondary source
is supplied to the monitor, the monitor will automatically switch to the new video source.
When current video input signal is not present, the monitor searches for a video signal from
the other video input port. If the video signal is present in the other port, then the monitor
switches the video source input port to the new found video source automatically.
VIDEO DETECT
DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO inputs will have priority over
DVI, VGA, RGB/HV. When DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2 or S-VIDEO
input signal is present the monitor will change and keep to the DVD/HD1, DVD/HD2, SCART,
VIDEO1, VIDEO2 or S-VIDEO input.
CUSTOM DETECT
Set the priority of input signals.
When CUSTOM DETECT is selected, monitor searches listed inputs only.
INPUT CHANGE
Sets input change speed.
NOTE: When “QUICK” is selected, picture may be distorted when signal input is changed.
This function should be chosen after all adjustment options have been made for the input.
LONG CABLE COMP
Manually compensates for image degradation caused from using a long cable.
EQUALIZE
FIRST DETECT
NORMAL
OFF
VGA, RGB/HV inputs only
POLE
Adjusts frequency.
0
PEAK
Adjusts equalizing value.
0
*: The product you purchased may not have this feature.
English-24
Downloaded From TV-Manual.com Manuals
Adjusts gain value.
0
OFFSET
Adjusts slice level of synchronized signal.
0
SYNC TERMINATE
Selects the terminate resistance for matching the cable impedance.
HIGH
RGB/HV inputs only
TERMINAL SETTING
DVI MODE
Selects the kind of DVI-D equipment which is connected to the DVI input. Select “DVI-PC”
when PC or other computer equipment is connected. Select “DVI-HD” when DVD player,
which has DVI-D output, is connected.
BNC MODE
Selects the kind of equipment which is connected to the BNC input.
RGB: Analog input
COMPONENT: Component
VIDEO:
RGB
SCART MODE
Input mode for devices using SCART connectors.
OFF
HDMI SIGNAL
RAW: Disable the expanded feature.
EXPAND: Expand image contrast and increase detail in the dark and bright areas.
SCAN CONVERSION
All inputs except VGA, RGB/HV
Selects the IP (Interlace to Progressive) conversion function.
Note: For DVI input “DVI-HD” needs to be enabled in the DVI mode menu.
PROGRESSIVE
Converts interlaced signals to progressive. This is the default setting.
INTERLACE
Disables IP conversion. This setting is best suited for motion pictures, but increases the risk
of image retention.
COLOR SYSTEM
The selected Color System depends on the video format of the input signal.
DVI-PC
EXPAND
PROGRESSIVE
AUTO
VIDEO1, VIDEO2, S-VIDEO inputs only
AUTO
Automatically chooses Color System setting based on input signal.
NTSC
PAL
SECAM
4.43 NTSC
PAL-60
SCAN MODE
Some video formats may require different scanning modes in order to best display the image.
OVER SCAN
HDMI, DVD/HD1, DVD/HD2, SCART, VIDEO1, VIDEO2, S-VIDEO, TV* inputs only
OVER SCAN
Image size is larger than what can be displayed. The image edge will appear cropped.
Approximately 95% of the image will be shown on the screen.
UNDER SCAN
Image size stays within the display area. The whole image is displayed on the screen.
ADVANCED OPTION
RESET
Resets the following settings within the ADVANCED OPTION menu back to factory setting:
INPUT DETECT, INPUT CHANGE, LONG CABLE COMP, TERMINAL SETTING, SCAN
CONVERSION, COLOR SYSTEM, SCAN MODE.
-
FACTORY RESET
Resets OSD options back to factory settings EXCEPT FOR: DATE & TIME, LANGUAGE,
OSD ROTATION, INPUT NAME, CHANGE SECURITY PASSWORD, SECURITY LOCK and
SECURITY PASSWORD.
-
*: The product you purchased may not have this feature.
English-25
Downloaded From TV-Manual.com Manuals
English
GAIN
NOTE 1: CREATING A SCHEDULE
The schedule function allows the display to be set to power on and off at different times. Up to seven different schedules can be
programmed.
To program the schedule:
1. Enter the SCHEDULE menu. Highlight SCHEDULE SETTINGS using the up and down buttons. Press the SET or the + button to enter the
Settings menu. Highlight the desired schedule number and press set. The box next to the number will turn yellow. The schedule can now
be programmed.
2. Use the down button to highlight the hours setting in the ON time slot. Use the + and - buttons to set the hour. Use the up and down
buttons to highlight the minutes setting. Use the + and - buttons to set the minutes. Set the OFF time in the same manner.
3. Use the up and down arrows to highlight INPUT. Use the + and - buttons to choose the input source. Use the up and down arrows to
highlight PIC. MODE. Use the + and - buttons to choose the picture mode.
4. Use the down button to select a day on which the schedule will be enabled. Push the
set button to enable. If the schedule is to be ran every day, choose EVERY DAY and
press the SET button. The circle next to EVERY DAY will turn yellow. If a weekly
schedule is desired, choose the days of the week using the up and down buttons and
pressing SET to select. Then highlight the EVERY WEEK option and press SET.
5. After a schedule is programmed the remaining schedules can then be set. Press
MENU to leave the OSD or press EXIT to go back to the previous menu.
DVI
SCHEDULE:
OFF TIMER
SCHEDULE SETTINGS
SCHEDULE LIST
DATE & TIME
SCHEDULE RESET RESET
Note: If schedules are overlapping then the schedule with the highest number will have
priority over the schedule with the lowest number. For example schedule #7 will have
priority over schedule #1.
If selected input or picture mode is not available now, disable input or picture mode
is shown in red.
(THU) JUN.18.2009 15:38
SETTINGS:
1
2
3
ON:
OFF:
INPUT:
PIC. MODE:
EVERY DAY
EVERY WEEK
MON TUE
FRI
Choose
Mark
4
5
6
7
––:––
––:––
––––
––––
WED
SAT
Return
THU
SUN
Close
NOTE 2: IMAGE PERSISTENCE
Please be aware that LCD Technology may experience a phenomenon known as Image Persistence. Image Persistence occurs when a
residual or “ghost” image of a previous image remains visible on the screen. Unlike CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a long period of time should be avoided.
To alleviate image persistence, turn off the monitor for as long as the previous image was displayed. For example, if an image was on the
monitor for one hour and a residual image remains, the monitor should be turned off for one hour to erase the image.
As with all personal display devices, NEC DISPLAY SOLUTIONS recommends displaying moving images and using a moving screen
saver at regular intervals whenever the screen is idle or turning off the monitor when not in use.
Please set “SCREEN SAVER”, “DATE &TIME” and “SCHEDULE SETTINGS” functions to further reduce the risk of Image persistence.
For long life use as Public Display
Image Sticking of LCD Panel
When an LCD panel is operated continuously for long hours, a trace of electric charge remains near the electrode inside LCD, and residual
or “ghost” image of previous image may be observed. (Image Persistence)
Image Persistence is not permanent, but when fixed image is displayed for long period, ionic impurities inside LCD are accumulated along
the displayed image, and may be permanent. (Image Sticking)
Recommendations
To prevent Image Sticking, and for longer life usage of LCD, the following are recommended.
1. Fixed image should not be displayed for long period. Change fixed images after short intervals.
2. When not in use, please turn off the monitor by remote control, or use Power Management or use Schedule Functions.
3. Lower environmental temperatures prolong the lifespan of the monitor.
When Protective surface (glass, acrylic) is installed over the LCD surface, the LCD surface is located in an enclosed space, the monitor
are stacked, utilize the temperature sensors inside monitor.
To reduce the environmental temperature, use the Cooling Fan, Screen Saver and Low Brightness.
4. Please use “Screen Saver Mode” of monitor.
English-26
Downloaded From TV-Manual.com Manuals
English
Remote Control Function
REMOTE CONTROL ID FUNCTION
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote works
Remote works
Remote works
REMOTE CONTROL ID
The remote control can be used to control up to 100 individual MultiSync monitors using
what is called the REMOTE CONTROL ID mode. The REMOTE CONTROL ID mode
works in conjunction with the Monitor ID, allowing control of up to 100 individual
MultiSync monitors. For example: if there are many monitors being used in the same
area, a remote control in normal mode would send signals to every monitor at the same
time (see Figure 1). Using the remote in REMOTE CONTROL ID mode will only operate
one specific monitor within the group (see Figure 2).
TO SET REMOTE CONTROL ID
While holding down the REMOTE ID SET button on the remote control, use the KEYPAD
to input the Monitor ID (1-100) of the display to be controlled via remote. The remote can
then be used to operate the monitor having that specific Monitor ID number.
When 0 is selected or when the remote control is in normal mode, all monitors will be
operated.
TO SET/RESET REMOTE CONTROL MODE
ID Mode - To enter ID Mode press the REMOTE ID SET button and hold down for
2 seconds.
Normal Mode - To return to Normal Mode press the REMOTE ID CLEAR button and hold
down for 2 seconds.
In order for this feature to work properly, the display must be assigned a Monitor ID
number. The Monitor ID number can be assigned under the MULTI DISPLAY menu in the
OSD (See page 23).
Figure 1
Remote in
Normal mode or
the REMOTE ID
is set to 0
Monitor ID:1
Monitor ID:2
Monitor ID:3
Remote does
not work
Remote does
not work
Remote works
Figure 2
Remote set up to
use REMOTE
ID:3
Point the remote control towards the remote sensor of the desired monitor and press the
REMOTE ID SET button. The MONITOR ID number is shown on the display when your remote control is in ID mode.
Use the remote control to operate a monitor that has a specific MONITOR ID number assigned to it.
1. Set the MONITOR ID number for the display (See page 23). The MONITOR ID number can range from 1-100.
This MONITOR ID number allows the remote control to operate this specific monitor without affecting other monitors.
2. On the remote control, press and hold down the REMOTE ID SET button while using the keypad to input the REMOTE CONTROL ID
number (1-100). The REMOTE ID NUMBER should match the MONITOR ID number of the display to be controlled. Choose “0” to
simultaneously control all displays in range.
3. Point the remote control towards the remote sensor of the desired monitor and press the REMOTE ID SET button.
The MONITOR ID number is shown in red on the display.
If the REMOTE CONTROLID is “0”, then all displays in range will show their respective MONITOR ID number in red.
If the MONITOR ID number is shown in white on the display, the MONITOR ID number and the REMOTE CONTROL ID are not the same.
This LCD monitor can be controlled via personal computer or wireless remote control using an RS-232C connection.
MONITOR ID and IR CONTROL
Using one PC or one infrared wireless controller, up to 100 individual LCD monitors can be controlled through a daisy chain via RS-232C
connection.
1. Connect PC and LCD monitors.
Connect a PC’s RS-232C control output to the LCD monitor RS-232C input. You can then connect the RS-232C output from the LCD
monitor to another LCD monitor RS-232C input. Up to 100 monitors can be connected using RS-232C.
2. Set Monitor ID and IR Control mode.
For proper operation, the Monitor ID should be set in the OSD menu of each monitor that is in the chain. The Monitor ID can be set under
the “MULTI DISPLAY” menu in the OSD. The Monitor ID number can be set within a range from 1 to 100. No two monitors should share
the same Monitor ID number. It is recommended to number each monitor in a daisy chain sequentially from 1. The first monitor in the daisy
chain is designated as the primary monitor. Subsequent monitors with the chain are secondary monitors.
In the “ADVANCED OPTION” menu on the first monitor in the RS-232C daisy chain set the “IR CONTROL” to “PRIMARY”.
Set the “IR CONTROL” to “SECONDARY” on all other monitors.
English-27
Downloaded From TV-Manual.com Manuals
3. Press the “DISPLAY” button on the remote control while aiming at the “PRIMARY” monitor. The Information OSD will be shown at
top left side of the screen.
Monitor ID: Displays the ID number of the current monitor within the daisy chain.
Target ID: Displays the ID number of the monitor that to be controlled via daisy chain from the current monitor.
Press the “+” or “-” buttons to change the “Target ID” to show the ID number of the monitor to be controlled. To control the entire daisy
chained monitors simultaneously, select “ALL” as the “Target ID.”
4. Use the wireless remote controller to control the “SECONDARY” monitor while aiming at the “PRIMARY” monitor.
The “MENU OSD” will appear on the selected target monitor.
NOTE:
If the “ID No.” mode select OSD is showing, press the “DISPLAY” button on the remote control while pointing at the “PRIMARY”
monitor to clear this OSD.
HINT:
If you lost control due to the incorrect setting of “IR CONTROL”, pressing the “DISPLAY” button on the remote control for 5 or
more seconds will reset the “IR CONTROL” menu to “NORMAL” function.
WIRED REMOTE CONTROL FUNCTION
You can control this monitor by connecting REMOTE IN/OUT with Stereo Mini plug cable (3.5
MultiSync
Remote IN
IN
).
MultiSync
Remote OUT
Remote IN
Remote OUT
OUT
MultiSync
Remote control cable
NOTE:
Remote control cable
Turn off the main power switch before connect/disconnect Stereo Mini plug cable.
English-28
Downloaded From TV-Manual.com Manuals
This LCD monitor can be controlled by connecting a personal computer with a RS-232C terminal.
NOTE: When you use this function, EXTERNAL CONTROL should be “RS-232C” (See page 23).
Functions that can be controlled by a personal computer are:
•
Power ON or OFF
•
Switching between input signals
Connection
LCD Monitor + PC
PC
(Out)
IN
MultiSync
OUT
RS-232C (IN)
MultiSync
RS-232C (OUT)
RS-232C Cable
RS-232C (IN)
RS-232C (OUT)
RS-232C Cable
MultiSync
NOTE: If your PC is equipped only with a 25-pin serial port connector, a 25-pin serial port adapter is required. Contact your
dealer for details.
* In order to function, the RS-232C OUT terminal can only be connected to another monitor of the same model.
Do not connect to other types of equipment.
To control monitor or multiple monitors that are daisy-chained together please use the control command. Instructions for the
control command can be found on the CD included with the display. The file is called “External_control.pdf”.
Multiple monitors that are daisy-chained have a limit to the conectable monitor.
1) Interface
PROTOCOL
RS-232C
BAUD RATE
9600 [bps]
DATA LENGTH
8 [bits]
PARITY BIT
NONE
STOP BIT
1 [bit]
FLOW CONTROL
NONE
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
The reverse type cable (null modem cable) (not include) should be used for RS-232C control.
2) Control command diagram
Please see file “External_Control.pdf” on the CD-ROM.
English-29
Downloaded From TV-Manual.com Manuals
English
Controlling the LCD monitor via RS-232C Remote Control
Controlling the LCD monitor via LAN Control
Connecting to a Network
Using a LAN cable allows you to specify the Network Settings and the Alert Mail Settings by using an HTTP server function.
NOTE: When you use this function, EXTERNAL CONTROL should be “LAN” (See page 23).
To use a LAN connection, you are required to assign an IP address.
Example of LAN connection:
Server
NOTE: Use a category 5 or higher LAN cable.
Hub
LAN cable
(not supplied)
Network Setting by Using an HTTP Browser
Overview
Connecting the monitor to a network allows for monitor control from a computer via the network.
To perform the monitor control from a web browser, you must have an exclusive application installed on your computer.
The IP address and subnet mask of the monitor can be set on the Network Setting screen of the web browser by using an
HTTP server function. Please be sure to use “Microsoft Internet Explorer 6.0” or a higher version for the web browser.
(This device uses “JavaScript” and “Cookies” and the browser should be set to accept these functions. The setting method will
vary depending on the version of browser. Please refer to the help files and the other information provided in your software.)
Access is gained to the HTTP server function by starting the Web browser on the computer via the network connected to the
monitor and entering the following URL.
Network Setting
http://<the Monitor’s IP address>/index.html
TIP:
The default IP address is “192.168.0.10”.
The exclusive application can be downloaded from our website.
NOTE: If the MONITOR NETWORK SETTINGS screen does not appear in the web browser, press the Ctrl+F5 keys to
refresh your web browser (or clear the cache).
The display or button’s response can be slowed down or operation may not be accepted depending the settings of
your network.
Should this happen, consult your network administrator.
The LCD monitor may not respond if its buttons are repeatedly pressed in rapid intervals. Should this happen, wait a
moment and repeat.
If you still can’t get a response, turn off and back on the monitor.
English-30
Downloaded From TV-Manual.com Manuals
Connect the monitor to a commercially available LAN cable before engaging in browser operations.
Operation with a browser that uses a proxy server may not be possible depending on the type of proxy server and the setting
method. Although the type of proxy server will be a factor, it is possible that items that have actually been set will not be
displayed depending on the effectiveness of the cache, and the contents set from the browser may not be reflected in
operation. It is recommended that a proxy server not be used unless it is unavailable.
Handling of the Address for Operation via a Browser
Regarding the actual address that is entered for the address or entered into the URL column when operation of the monitor is
via a browser, the host name can be used as it is when the host name corresponding to the IP address of the monitor has
been registered to the domain name server by a network administrator, or the host name corresponding to the IP address of
the monitor has been set in the “HOSTS” file of the computer being used.
Example 1:
When the host name of the monitor has been set to “pd.nec.co.jp”, access is gained to the network setting by
specifying http://pd.nec.co.jp/index.html for the address or the entry column of the URL.
Example 2:
When the IP address of the monitor is “192.168.73.1”, access is gained to the mail alert settings by specifying
http://192.168.73.1/index.html for the address or the entry column of the URL.
Network Settings
http://<the Monitor’s IP address> /index.html
DHCP
Enabling this option automatically assigns an IP address to the monitor from your DHCP server.
Disabling this option allows you to register the IP address or subnet mask number obtained from
your network administrator.
NOTE: The IP address of the monitor is required to change the network setting.
The IP address will not be displayed on the Monitor’s menu.
Consult your network administrator for the IP address when [ENABLE] is selected for
[DHCP].
IP ADDRESS
Set your IP address of the network connected to the monitor when [DISABLE] is selected for
[DHCP].
SUBNET MASK
Set your subnet mask number of the network connected to the monitor when [DISABLE] is selected
for [DHCP].
DEFAULT GATEWAY
Set your default gateway of the network connected to the monitor when [DISABLE] is selected for
[DHCP].
DNS (PRIMARY)
Set your primary DNS settings of the network connected to the monitor.
DNS (SECONDARY)
Set your secondary DNS settings of the network connected to the monitor.
UPDATE
Reflect your settings.
NOTE: Close the browser after clicking [UPDATE].
The monitor will automatically update your settings.
English-31
Downloaded From TV-Manual.com Manuals
English
Preparation Before Use
Alert Mail Setting
http://<the Monitor’s IP address>/lanconfig.html
This option notifies your computer of an error message via e-mail when using wired LAN. An error message notification will be
sent when an error occurs in the monitor.
HOST NAME
Type in the hostname of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
DOMAIN NAME
Type in the domain name of the network connected to the monitor.
Up to 60 alphanumeric characters can be used.
ALERT MAIL
Checking [ENABLE] will turn on the Alert Mail feature.
Checking [DISABLE] will turn off the Alert Mail feature.
SENDER’S ADDRESS
Type in the senders address. Up to 60 alphanumeric and symbols characters can be used.
SMTP SERVER NAME
Type in the SMTP server name to be connected to the monitor.
Up to 60 alphanumeric characters can be used.
RECIPIENT’S
ADDRESS 1 to 3
Type in your recipient’s address. Up to 60 alphanumeric and symbols characters can be used.
APPLY
Click this button to reflect the above settings.
EXECUTE
Click this button to send a test mail to check if your settings are correct.
STATUS
A reply to a test mail will be displayed.
NOTE: • If you execute a test, you may not receive an Alert mail.
Should this happen, check if the network settings are correct.
• If you entered an incorrect address in a test, you may not receive an Alert mail.
Should this happen, check if the Recipient’s Address is correct.
TIP:
The Alert Mail settings will not be affected even when [RESET] is done from the menu.
For Control command diagram, please see file “External_Control.pdf” on the CD-ROM.
English-32
Downloaded From TV-Manual.com Manuals
Reduced Footprint: Provides the ideal solution for environments requiring superior image quality but with size and weight
limitations.
Color Control Systems: Allows you to adjust the colors on your screen and customize the color accuracy of your monitor to
a variety of standards.
OmniColor: Combines Six-axis color control and the sRGB standard. Six-axis color control permits color adjustments via six
axes (R, G, B, C, M and Y) rather than through the three axes (R, G and B) previously available. The sRGB standard provides
the monitor with a uniform color profile. This assures that the colors displayed on the monitor are exactly the same as on the
color printout (with sRGB supporting operating system and sRGB printer). This allows you to adjust the colors on your screen
and customise the color accuracy of your monitor to a variety of standards.
sRGB Color Control: A new optimized color management standard which allows for color matching on computer displays
and other peripherals. The sRGB standard, which is based on a calibrated color space, allows for optimal color representation
and backward compatibility with other common color standards.
OSD (On-Screen-Display) Controls: Allow you to quickly and easily adjust all elements of your screen image via simple to
use on-screen menus.
Plug and Play: The Microsoft® solution with the Windows® operating system facilitates setup and installation by allowing the
monitor to send its capabilities (such as screen size and resolutions supported) directly to your computer, automatically
optimizing display performance.
IPM (Intelligent Power Manager) System: Provides innovative power-saving methods that allow the monitor to shift to a
lower power consumption level when on but not in use, saving two-thirds of your monitor energy costs, reducing emissions
and lowering the air conditioning costs of the workplace.
FullScan Capability: Allows you to use the entire screen area in most resolutions, significantly expanding image size.
VESA Standard (FDMIv1) Mounting Interface: Allows users to connect their LCD monitor to any VESA standard (FDMIv1)
third party mounting arm or bracket. Allows for the monitor to be mounted on a wall or an arm using any third party compliant
device. NEC recommends using mounting interface that comply with TÜV-GS and/or UL1678 standard in North America.
DVI-D: The digital-only subset of DVI ratified by the Digital Display Working Group (DDWG) for digital connections between
computers and displays. As a digital-only connector, analog support is not provided for a DVI-D connector. As a DVI-based
digital only connection, only a simple adapter is necessary for compatibility between DVI-D and other DVI-based digital
connectors such as DFP and P&D. The DVI interface of this display supports HDCP.
TILE MATRIX, TILE COMP: Shows one image over multiple screens with accuracy while compensating for bezel width.
ZOOM: Expands image size for horizontal and vertical direction.
RS-232C daisy chain: You can control the multiple monitors by controller or wireless remote controller.
Self-diagnosis: If an internal error should occur, a failure state will be indicated.
Long cable capability: Automatic long cable compensation prevents image quality degradation (dull signals) caused by long
cable lengths.
English-33
Downloaded From TV-Manual.com Manuals
English
Features
Troubleshooting
No picture
• The signal cable should be completely connected to the
display card/computer.
•
The display card should be completely seated in its slot.
•
Front Power Switch and computer power switch should
be in the ON position.
•
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
•
Check the monitor and your display card with respect to
compatibility and recommended settings.
•
Check the signal cable connector for bent or pushed-in
pins.
Power Button does not respond
• Unplug the power cord of the monitor from the AC outlet
to turn off and reset the monitor.
Image persistence
• Please be aware that LCD Technology may experience a
phenomenon known as Image Persistence. Image
Persistence occurs when a residual or “ghost” image of a
previous image remains visible on the screen. Unlike
CRT monitors, LCD monitors’ image persistence is not
permanent, but constant images being displayed for a
long period of time should be avoided. To alleviate image
persistence, turn off the monitor for as long as the
previous image was displayed. For example, if an image
was on the monitor for one hour and a residual image
remains, the monitor should be turned off for one hour to
erase the image.
NOTE: As with all personal display devices, NEC DISPLAY
SOLUTIONS recommends displaying moving
images and using a moving screen saver at regular
intervals whenever the screen is idle or turning off
the monitor when not in use.
RED LED on monitor is blinking
• A certain failure might have occurred, please contact
your nearest authorized NEC DISPLAY SOLUTIONS
service facility.
•
If the monitor is powered off by the inside temperature
being higher than the normal operating temperature, a
RED LED will blink six times. Power on the display again
after confirming the inside temperature has been
reduced to normal operation temperature.
Display image is not sized properly
• Use the OSD Image Adjust controls to increase or
decrease the coarse adjustment.
•
Check to make sure that a supported mode has been
selected on the display card or system being used.
(Please consult display card or system manual to
change graphics mode.)
Selected resolution is not displayed properly
• Use OSD Display Mode to enter Information menu and
confirm that the appropriate resolution has been
selected. If not, select corresponding option.
No Sound
• Check to see if audio cable is properly connected.
•
Check to see if mute is activated.
•
Check to see if volume is set at minimum.
•
Check to see if computer supports an audio signal
through DisplayPort.
If unsure, contact the computer manufacturer.
Remote Control is not available
• Check the Remote Control’s batteries status.
•
Check if batteries are inserted correctly.
•
Check if the Remote Control is pointing at the monitor’s
remote sensor.
•
Check the Remote Control Mode status.
•
The remote control system may not function when direct
sunlight or strong illumination strikes the remote control
sensor of the LCD monitor, or when there is an object in
the path.
Image is unstable, unfocused or swimming is apparent
• Signal cable should be completely attached to the
computer.
•
Use the OSD Image Adjust controls to focus and adjust
display by increasing or decreasing the fine adjustment.
When the display mode is changed, the OSD Image
Adjust settings may need to be re-adjusted.
“SCHEDULE”/“OFF TIMER” function is not working
properly
• The “SCHEDULE” function will be disabled when the
“OFF TIMER” is set.
•
Check the monitor and your display card with respect to
compatibility and recommended signal timings.
•
•
If your text is garbled, change the video mode to noninterlace and use 60Hz refresh rate.
Image of component signal is greenish
• Check to see if the DVD/HD input connector is selected.
LED on monitor is not lit
(no green or red color can be seen)
• Power Switch should be in the ON position and power
cord should be connected.
If the “OFF TIMER” function is enabled and the power to
the LCD monitor is turned off when the power supply is
interrupted unexpectedly, then the “OFF TIMER” will be
reset.
Snowy Picture, Poor Sound in TV
• Check antenna/cable connection. Use new cable if
necessary.
Interference in TV
• Check components for shielding, move away from
monitor if necessary.
•
Make certain the computer is not in a power-saving
mode (touch the keyboard or mouse).
RS-232C or LAN control is not available
• Check RS-232C or LAN cable connection.
•
Check to see that the power indicator option in the OSD
is set to ON.
•
Check “CONTROL” setting in “EXTERNAL CONTROL”.
Either light vertical or horizontal stripes may appear, depending on the specific display pattern. This is no product fault or
degradation.
English-34
Downloaded From TV-Manual.com Manuals
English
Specifications - P401
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
40" /101.6 cm diagonal
0.461 mm
1920 x 1080
Over 16 million colors (depending on video card used)
650 cd/m2 (Max.), 500 cd/m2 (Typ.) @25°C
3000:1
89° (typ) @ CR>10
1100 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
885.6 x 498.2 mm
Input Signal
DVI
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
DVI-D 24pin
15pin Mini D-sub
BNC (R,G,B,H,V)
HDMI
HDMI Connector
Digital RGB
HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1
DVD/HD2
RCA (Y, Cb/Pb, Cr/Pr)
BNC
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO1
VIDEO2
BNC/RCA
BNC
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2
BNC
Output Signal
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
Composite
1.0 Vp-p with 75 ohm terminated
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
VIDEO1/VIDEO2 BNC
AUDIO
AUDIO
Input
AUDIO
Output
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
RCA (L/R)
Stereo L/R 0.5 Vrms
Analog Audio
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In:
RS-232C Out:
LAN:
Remote IN:
Remote OUT:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
RJ-45 10/100 BASE-T
Stereo Mini jack 3.5
Stereo Mini jack 3.5
3.5 - 1.45 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)
20 - 80% (without condensation)
0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature:
Humidity:
-20 - 60°C / -4 - 140°F
10 - 90% (without condensation) / 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
919.7 (W) x 532.2 (H) x 140.0 (D) mm / 36.2 (W) x 21.0 (H) x 5.5 (D) inches
Weight
24.0 Kg (52.9 lbs)
VESA compatible arm mounting interface
300 mm x 300 mm (M6, 4 Holes)
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI, DisplayPort
Accessories
Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for optional stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-35
Downloaded From TV-Manual.com Manuals
Specifications - P461
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
46" /116.8 cm diagonal
0.530 mm
1920 x 1080
Over 16 million colors (depending on video card used)
650 cd/m2 (Max.), 500 cd/m2 (Typ.) @25°C
4000:1
89° (typ) @ CR>10
1300 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
1018.1 x 572.7 mm
Input Signal
DVI
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
DVI-D 24pin
15pin Mini D-sub
BNC (R,G,B,H,V)
HDMI
HDMI Connector
Digital RGB
HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1
DVD/HD2
RCA (Y, Cb/Pb, Cr/Pr)
BNC
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO1
VIDEO2
BNC/RCA
BNC
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2
BNC
Output Signal
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
Composite
1.0 Vp-p with 75 ohm terminated
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
VIDEO1/VIDEO2 BNC
AUDIO
AUDIO
Input
AUDIO
Output
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
RCA (L/R)
Stereo L/R 0.5 Vrms
Analog Audio
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In:
RS-232C Out:
LAN:
Remote IN:
Remote OUT:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
RJ-45 10/100 BASE-T
Stereo Mini jack 3.5
Stereo Mini jack 3.5
3.9 - 1.6 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)
20 - 80% (without condensation)
0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature:
Humidity:
-20 - 60°C / -4 - 140°F
10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1055.4 (W) x 608.6 (H) x 140.0 (D) mm / 41.6 (W) x 24.0 (H) x 5.5 (D) inches
Weight
29.0 Kg (63.9 lbs)
VESA compatible arm mounting interface
300 mm x 300 mm (M6, 4 Holes)
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI, DisplayPort
Accessories
Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for optional stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-36
Downloaded From TV-Manual.com Manuals
English
Specifications - P521
Product Specifications
LCD Module
Pixel Pitch:
Resolution:
Color:
Brightness:
Contrast Ratio:
Viewing Angle:
Design View Distance:
Frequency
Horizontal:
Vertical:
52" /132.1 cm diagonal
0.6 mm
1920 x 1080
Over 16 million colors (depending on video card used)
700 cd/m2 (Max.), 500 cd/m2 (Typ.) @25°C
2000:1
89° (typ) @ CR>10
1300 mm
15.625/15.734 kHz, 31.5 kHz - 91.1 kHz (Analog Input)
31.5 kHz - 91.1 kHz (Digital Input)
50.0 - 85.0 Hz
Pixel Clock
25.2 MHz - 162.0 MHz
Viewable Size
1152.0 x 648.0 mm
Input Signal
DVI
Digital RGB
DVI (HDCP)
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
DisplayPort DisplayPort Connector Digital RGB
DisplayPort Complies with Standard V1.1a, applicable to HDCP1.3
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920x1080 (60 Hz)
VGA
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
Analog RGB
0.7 Vp-p/75 ohm
VGA60, SVGA60, XGA60, WXGA60, SXGA60, UXGA60*1, 1920X1080 (60Hz)
Sync
Separate: TTL level (Pos./Neg.)
Composite sync on Green Video: 0.3 Vp-p Neg.
RGB/HV
DVI-D 24pin
15pin Mini D-sub
BNC (R,G,B,H,V)
HDMI
HDMI Connector
Digital RGB
HDMI
1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz
DVD/HD1
DVD/HD2
RCA (Y, Cb/Pb, Cr/Pr)
BNC
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
HDTV/DVD: 1080p, 1080i, 720p@50Hz/60Hz, 576p@50Hz, 480p@60Hz, 576i@50Hz, 480i@60Hz
VIDEO1
VIDEO2
BNC/RCA
BNC
Composite
1.0 Vp-p/75 ohm
NTSC/PAL/SECAM/4.43NTSC/PAL60
S-VIDEO
Mini DIN 4 pin
S-VIDEO
Y: 1.0 Vp-p/75 ohm C: 0.286 Vp-p/75 ohm (NTSC), 0.3 Vp-p/75 ohm (PAL/SECAM)
NTSC/PAL/SECAM/4.43NTSC/PAL60
RGB/HV
BNC (R,G,B,H,V)
Analog RGB
0.7 Vp-p with 75 ohm terminated
Separate HV sync: TTL level (Posi / Nega)
DVD/HD2
BNC
Output Signal
Component
Y: 1.0 Vp-p/75ohm, Cb/Cr (Pb/Pr): 0.7 Vp-p/75 ohm
Composite
1.0 Vp-p with 75 ohm terminated
RCA (L/R) X2
STEREO Mini Jack
Analog Audio
Stereo L/R 0.5 Vrms
HDMI Connector
VIDEO1/VIDEO2 BNC
AUDIO
AUDIO
Input
AUDIO
Output
Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
DisplayPort Connector Digital Audio
PCM 32, 44.1, 48 KHz (16/20/24bit)
RCA (L/R)
Stereo L/R 0.5 Vrms
Analog Audio
Speaker Output
Control
External Speaker Jack 15 W + 15 W (8 ohm)
RS-232C In:
RS-232C Out:
LAN:
Remote IN:
Remote OUT:
Power Supply
9 Pin D-sub
9 Pin D-sub (with daisy chain)
RJ-45 10/100 BASE-T
Stereo Mini jack 3.5
Stereo Mini jack 3.5
4.9 - 2.0 A @ 100-240VAC, 50/60Hz
Operational Environment
Temperature:
Humidity:
Altitude:
5 - 40°C / 41 - 104°F (Default brightness), 5 - 20°C / 41 - 68°F (Max brightness)
20 - 80% (without condensation)
0 - 3000 m (Brightness may decrease with altitude)
Storage Environment
Temperature:
Humidity:
-20 - 60°C / -4 - 140°F
10 - 90% (without condensation)/ 90% - 3.5% x (Temp - 40°C) regarding over 40°C
Dimension
1200.0 (W) x 696.0 (H) x 147.5 (D) mm / 47.2 (W) x 27.4 (H) x 5.8 (D) inches
Weight
40.0 Kg (88.2 lbs)
VESA compatible arm mounting interface
400 mm x 400 mm (M6, 4 Holes)
Power Management
VESA DPM
Plug & Play
VESA DDC2B, DDC/CI, DisplayPort
Accessories
Setup manual, Power Cord, Video Signal cable, Remote Control, AA Battery x 2, Clamp x 3,
Screw x 9, CD-ROM, Thumbscrew for optional stand x 2, Cable cover
NOTE: Technical specifications are subject to change without notice.
*1: Compressed image
English-37
Downloaded From TV-Manual.com Manuals
Pin Assignment
1) RS-232C input/output
Pin No
Name
1
connected to 7&8
2
RXD
3
TXD
4
connected to 6
5
GND
6
connected to 4
7
connected to 1&8
8
connected to 1&7
9
NC
D-SUB 9P
5
1
6
This LCD monitor uses RXD, TXD and GND lines for RS-232C control.
2) REMOTE IN
3) REMOTE OUT
English-38
Downloaded From TV-Manual.com Manuals
9
NEC DISPLAY SOLUTIONS is strongly committed to environmental protection and sees recycling as one of the company’s
top priorities in trying to minimize the burden placed on the environment. We are engaged in developing environmentallyfriendly products, and always strive to help define and comply with the latest independent standards from agencies such as
ISO (International Organisation for Standardization) and TCO (Swedish Trades Union).
Disposing of your old NEC product
The aim of recycling is to gain an environmental benefit by means of re-use, upgrading, reconditioning or reclamation of
material. Dedicated recycling sites ensure that environmentally harmful components are properly handled and securely
disposed. To ensure the best recycling of our products, NEC DISPLAY SOLUTIONS offers a variety of recycling
procedures and gives advice on how to handle the product in an environmentally sensitive way, once it has reached the end
of its life.
All required information concerning the disposal of the product and country-specific information on recycling facilities can be
found on our following websites:
http://www.nec-display-solutions.com/greencompany/ (in Europe),
http://www.nec-display.com (in Japan) or
http://www.necdisplay.com (in USA).
Energy Saving
This monitor features an advanced energy saving capability. When a VESA Display Power Management Signalling (DPMS)
Standard signal is sent to the monitor, the Energy Saving mode is activated. The monitor enters a single Energy Saving mode.
Mode
Power consumption
LED colour
Normal Operation
Approx. 175 W (P401)
Approx. 210 W (P461)
Approx. 290 W (P521)
Green
Energy Saving Mode
Less than 2 W
Amber Blinking
Power Off (STANDBY)
Less than 1 W
Amber
Power Off (Eco standby)
Less than 0.5 W
Red
WEEE Mark (European Directive 2002/96/EC)
Within the European Union
EU-wide legislation, as implemented in each Member State, requires that waste electrical and electronic
products carrying the mark (left) must be disposed of separately from normal household waste. This includes
monitors and electrical accessories, such as signal cables or power cords. When you need to dispose of your
NEC display products, please follow the guidance of your local authority, or ask the shop where you
purchased the product, or if applicable, follow any agreements made between yourself and NEC.
The mark on electrical and electronic products only applies to the current European Union Member States.
Outside the European Union
If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local
authority so as to comply with the correct disposal method.
English-39
Downloaded From TV-Manual.com Manuals
English
Manufacturer’s Recycling and Energy Information
Download PDF