Compatibility (Ultra Chair) Kit (002-1619-00)

Components:
Light Harness Jumper Kit [002-1619-00]
Harness................... 2
PCBoard.................. 1
Special Tools:
Wire Strippers
Small Screwdriver
Note
Applies to specific model lights installed on Ultra chairs.
- 153584, 153771, 153585, 153902, 153911, and 153912 lights on chairs S/N V1314209 - present
- 153914-xxx and 153915-xxx lights on chairs S/N before V1314209
Steps 1 - 3 only for halogen light models 153584, 153771, 153585, and 153902
WARNING
Always disconnect light from the power source before removing
any covers. Failure to do so may result in personal injury.
Step 1: Remove PC Board.
A) Disconnect power source.
B) Remove end cap screw and end cap, then slide cover back.
C) Disconnect wire connections and remove PC Board.
End Cap
To Console
or LR Hub
PC Board
J1
To Bulb
J2
TP200 Rev. A
Cover
Channel
End Cap
Screw
© 2012 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
Step 2: Wire Connections.
A) Install PC Board.
B) Connect wiring as shown.
English-1
Style A
003-2564-00 Rev. A (10/12)
Steps 1 - 3 only for halogen light models 153584, 153771, 153585, and 153902
Note
This adjustment allows setting the desired height (when light arm is lowered) of
light arm at which AUTO ON mode is activated (light automatically turns on).
On some units both end caps may need to be removed.
WARNING
Use caution when operating equipment
with covers removed.
Step 3: To adjust AUTO ON mode.
A)
B)
C)
Position light arm at desired height for AUTO ON
mode to activate and hold in this position.
Loosen two screws, slide trigger all the way out,
then slowly slide trigger in until lighthead turns
on at set point line.
Tighten two screws to secure trigger.
End Cap
Cover
Set Point
Line
End Cap
Screw
IN
OUT
Trigger
TP200 Rev. A
Screws
Note
Refer to separate LR or Console section in the following pages for remaining steps.
© 2012 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-2
Style A
Harness Installation Through Arm - For LR Only
Step 4: Remove cover.
A) Remove cover and screws as shown.
Note: This step applies to 153584, 153771, 153585, 153902, 153911, and 153912 lights on
chair S/N V1314209 to present (harness P/N 015-3177-00) and 153914-xxx and 153915-xxx
lights on chairs S/N before V1314209 (015-3176-00).
Step 5: Install harness.
A) Connect wire harness to end of light.
B) Connect other harness end to chair umbilical.
Cover
Step 6: Install cover.
A) Install cover and screws to secure.
Screws
Step 7: Finalize Installation.
A) Connect power source.
B) Verify operation.
TP200 Rev. A
New Light
(harness P/N 015-3176-00)
Harness
Connection
Previous Light
(harness P/N 015-3177-00)
© 2012 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-3
Style A
Harness Installation Through Arm - For Console Only
Step 4: Remove cover.
A) Remove console side cover.
Note: This step applies to 153584, 153771, 153585, 153902, 153911, and 153912 lights on chair S/N V1314209 to present (harness P/N 015-3177-00) and 153914-xxx and 153915-xxx lights on chairs S/N before V1314209 (015-3176-00).
Step 5: Install harness.
A) Connect wire harness to end of light.
B) Connect other harness end to chair umbilical.
Step 6: Install cover.
A) Move cover until it snaps into place.
Previous Light
(harness P/N 015-3177-00)
New Light
(harness P/N 015-3176-00)
Step 7: Finalize installation.
TP200 Rev. A
A) Connect power source.
B) Verify operation.
Harness
Connection
© 2012 Midmark Corp. | 60 Vista Drive Versailles, OH 45380 USA | 1-800-643-6275 | 1-937-526-3662 | midmark.com
English-4
Style A
Download PDF