Vulcan 810 Power Tilt [0501704] [09/2009]

Vulcan 810 Power Tilt [0501704] [09/2009]
OWNER'S MANUAL
810 POWER TILT
PARTS
NOTE: MANUAL including SPECIFICATIONS, subject to change without notice
All ratings specified are based on structural factors only,
not vehicle capacities or capabilities.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Phone (423) 238-7227 • FAX (423) 238-7237
FORM NO. 0501704
09 / 2009
PRICE $25.00
LIMITED WARRANTY
MILLER INDUSTRIES TOWING EQUIPMENT INC., hereinafter referred to as MILLER, warrants to the
original purchaser that each new MILLER wrecker or other MILLER products will be free from defects
in material and workmanship for a period of twelve (12) months from date placed in service, but in no
event shall such warranty period exceed twenty-four (24) months from date of manufacture by MILLER.
The purchaser must promptly notify MILLER in writing of any failure in material or workmanship. In no
event shall MILLER accept such notification later than twenty-four (24) months from date of delivery or
twelve (12) months from date placed in service, whichever is earlier.
MILLER's obligation under this warranty, statutory or otherwise, is limited to the repair or replacement
at the MILLER factory, or at a point designated by MILLER, of such part or parts as shall appear upon
inspection by MILLER to be defective in material or workmanship. New or remanufactured parts will
be used for any replacement at MILLER's option. This warranty is not transferable. This warranty does
not obligate MILLER to bear the cost of labor or transportation charges in connection with the repair
or replacement of any parts found to be defective, nor shall it apply to a product upon which repairs or
alterations have been made unless authorized by MILLER.
EXCEPT AS EXPRESSLY SET FORTH IN THIS WARRANTY, MILLER MAKES NO OTHER WARRANTY,
EXPRESS OR IMPLIED, AND HEREBY DISCLAIMS ALL OTHER WARRANTIES INCLUDING, BUT
NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A
PARTICULAR PURPOSE. MILLER shall in no event be liable for claimed downtime, claimed loss of
profits or goodwill, or any other special, incidental, indirect, or consequential damages concerning or
relating to any product or parts, whether based on negligence, strict liability, breach of contract, breach
of warranty, misrepresentation or any other legal theory, regardless of whether the loss resulted from
any general or particular requirement which MILLER knew or had reason to know about at the time
of sale.
MILLER MAKES NO WARRANTY, EXPRESS OR IMPLIED, AS TO THE FINISHED PRODUCTS
MANUFACTURED OR SUPPLIED BY ANOTHER MANUFACTURER AND SUPPLIED BY MILLER TO
PURCHASER, including, but not limited to, any vehicle to which a MILLER product may be affixed or
any accessories or wire rope, and MILLER EXPRESSLY DISCLAIMS ANY IMPLIED WARRANTIES OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE AS TO SUCH EQUIPMENT OR
PRODUCTS. This language shall in no way affect or diminish the rights of the purchaser to rely on such
warranties as are extended by such manufacturers or suppliers. MILLER shall, to the extent permitted
under applicable law, pass on to the purchaser such manufacturer's or seller's warranty.
MILLER, whose policy is one of continuous improvement, reserves the right to improve its products
through changes in design or materials as it may deem desirable without being obligated to incorporate
such changes in products previously sold. This warranty is not intended to cover or include the following
items, which are set forth by way of example and not limitation:
A.Normal deterioration of trim, paint, lettering, and appearance items due to wear or exposure to
weather, road conditions, road treatments, etc.
B.Any damage or defect due to accident, misuse, abuse, improper or unauthorized repairs, failure
to provide reasonable and necessary maintenance, or uses for which the equipment was not
designed or intended.
C.Alterations or modifications that affect performance, operation or reliability.
D.Normal maintenance parts including, but not limited to, wear pads, bushings, wire rope, mud
flaps, fenderettes, light bulbs, hydraulic oil, filters, and tow sling belts.
IT IS EXPRESSLY UNDERSTOOD THAT MILLER MAKES NO IMPLIED WARRANTY THAT MILLER
PRODUCTS SHALL BE FIT FOR THE PURPOSE OF LIFTING OR MOVING PEOPLE OR FOR ANY
OTHER IMPROPER USE.
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive
Ooltewah, Tennessee 37363
Telephone (423) 238-4171
SERIAL NUMBER
OWNER, USER AND OPERATOR:
We appreciate your choice of our wrecker for your application. Our
number one priority is user safety which is best achieved by our joint
efforts. We feel that you can make a major contribution to safety if
you, as the equipment owner and operator:
1.Comply with Federal, State, and Local Regulations.
2.Read, Understand, and Follow the Instructions in this Manual.
3.Use Good, Safe Work Practices in a Common Sense Way.
4.Only have Authorized and Trained Operators running the
Wrecker.
© 2009 MILLER INDUSTRIES TOWING EQUIPMENT INC. All rights reserved. Reproduction
or use, without express permission, of editorial or pictorial content, in any manner, is prohibited.
i
TABLE OF CONTENTS
Section I - PARTS
SUBFRAME ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-2 & I-3
BODY ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-4 & I-5
BOOM ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-6 & I-7
WHEEL LIFT ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . . I-8 thru I-11
TANK HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-12 & I-13
BOOM HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . . . . . . I-14 & I-15
WHEEL LIFT HYDRAULICS . . . . . . . . . . . . . . . . . . . . . . . I-16 & I-17
BOOM END SWIVEL ASSEMBLY . . . . . . . . . . . . . . . . . . . . . . . . I-18
ii
Section I - PARTS
This Section is provided by the manufacturer for the purpose of ordering any
component part of the Vulcan 810 Power Tilt that may be required when
part replacement is necessary. Be certain to use only original equipment
replacement parts for warranty purposes as well as for keeping your Vulcan
810 Power Tilt in its original state and optimum operating capacities.
When ordering replacement or spare parts be sure to provide the following
information to the manufacturer’s Parts Department.
1.
2.
3.
4.
5.
6.
7.
Manual Number & Date of Publication
Manual Page Number
Page Title
Reference Number of Part Desired
Part Number
Part Description
Quantity of Part Desired
Providing this information will help ensure that the correct parts will be
delivered to you in an expedient manner without delay. Should additional
information be required for repair or replacement of certain components,
contact your Wrecker Manufacturer Authorized Representative.
The Manufacturer reserves the right, without notice or obligation, to improve
or modify their products, which may change the specifications, models and
feature availability.
I-1
Section I - PARTS (cont'd)
810 POWER TILT SUBFRAME ASSEMBLY
I-2
Section I - PARTS (cont'd)
810 POWER TILT SUBFRAME ASSEMBLY
I-3
Section I - PARTS (cont'd)
810 POWER TILT BODY ASSEMBLY
I-4
Section I - PARTS (cont'd)
810 POWER TILT BODY ASSEMBLY
I-5
Section I - PARTS (cont'd)
810 POWER TILT BOOM ASSEMBLY
I-6
Section I - PARTS (cont'd)
810 POWER TILT BOOM ASSEMBLY
I-7
Section I - PARTS (cont'd)
810 POWER TILT
WHEEL LIFT ASSEMBLY
I-8
Section I - PARTS (cont'd)
810 POWER TILT
WHEEL LIFT ASSEMBLY
I-9
Section I - PARTS (cont'd)
810 POWER TILT
WHEEL LIFT ASSEMBLY (cont'd)
I-10
Section I - PARTS (cont'd)
810 POWER TILT
WHEEL LIFT ASSEMBLY (cont'd)
I-11
Section I - PARTS (cont'd)
810 POWER TILT TANK HYDRAULICS
I-12
Section I - PARTS (cont'd)
810 POWER TILT TANK HYDRAULICS
I-13
Section I - PARTS (cont'd)
810 POWER TILT BOOM HYDRAULICS
I-14
Section I - PARTS (cont'd)
810 POWER TILT BOOM HYDRAULICS
I-15
Section I - PARTS (cont'd)
810 POWER TILT WHEEL LIFT HYDRAULICS
I-16
Section I - PARTS (cont'd)
810 POWER TILT WHEEL LIFT HYDRAULICS
I-17
Section I - PARTS (cont'd)
BOOM SWIVEL ASSEMBLY
REF.
NO.
NO.
REQ'D
PART
NUMBER
1
1
0302916
--
2
3
4
5
6
7
--
1
1
1
1
1
2
805180000
0300113
804181500
805180001
805180002
852060100
9056098
DESCRIPTION
WIRE ROPE, 3/8" X 6 X 19 IPS
SHEAVE HOUSING ASSEMBLY
GREASE FITTING,1/4"-28 STRAIGHT
SHEAVE HOUSING CASTING
SHEAVE SHAFT
SHEAVE CASTING (WAS 9050504)
CABLE GUIDE ~ CASTING
RETAINING RING, EXT 1" NOM. HEAVY DUTY
I-18
NOTES
NOTES
NOTES
Miller Industries Towing Equipment Inc.
8503 Hilltop Drive • Ooltewah, Tennessee 37363 • (423) 238-7227
www.millerind.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement