Shockwave 26-inch BL Deep-V Manual

ShockWave 26
TM
26-INCH BRUSHLESS RTR DEEP–V BOAT
PRB08014
Owners Manual • Bedienungsanleitung
Manuel de l'utilisateur • Manuale dell'utente
EN
NOTICE
All instructions, warranties and other collateral documents are subject to change at the sole discretion of Horizon Hobby, LLC. For up-to-date
product literature, visit http://www.horizonhobby.com and click on the support tab for this product.
Meaning of Special Language
The following terms are used throughout the product literature to indicate various levels of potential harm when operating this product:
NOTICE: Procedures, which if not properly followed, create a possibility of physical property damage AND little or no possibility of injury.
CAUTION: Procedures, which if not properly followed, create the probability of physical property damage AND a possibility
of serious injury.
WARNING: Procedures, which if not properly followed, create the probability of property damage, collateral damage, and serious
injury OR create a high probability of superficial injury.
WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate
the product correctly can result in damage to the product, personal property and cause serious injury.
This is a sophisticated hobby product and NOT a toy. It must be operated with caution and common sense and requires some basic mechanical
ability. Failure to operate this Product in a safe and responsible manner could result in injury or damage to the product or other property. This
product is not intended for use by children without direct adult supervision. Do not use with incompatible components or alter this product in
any way outside of the instructions provided by Horizon Hobby, LLC. This manual contains instructions for safety, operation and maintenance. It
is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and
avoid damage or serious injury.
Age Recommendation: Not for children under 14 years. This is not a toy.
Safety Precautions and Warnings
As the user of this product, you are solely responsible for
operating in a manner that does not endanger yourself and
others or result in damage to the product or the property of
others.
• When handling and/or transporting your boat, always
pick up the boat from the front, keeping all moving parts
pointed away from you.
• Always keep a safe distance in all directions around
your model to avoid collisions or injury. This model is
controlled by a radio signal subject to interference from
many sources outside your control. Interference can
cause momentary loss of control.
• Always operate your model in open spaces away from
full-size vehicles, traffic and people.
• Always carefully follow the directions and warnings
for this and any optional support equipment (chargers,
rechargeable battery packs, etc.).
• Always keep all chemicals, small parts and anything
electrical out of the reach of children.
• Always avoid water exposure to all equipment not
specifically designed and protected for this purpose.
Moisture causes damage to unprotected electronics.
• Never place any portion of the model in your mouth
as it could cause serious injury or even death.
• Never operate your model with low transmitter batteries.
Table of Contents
Water-resistant Boat with Waterproof Electronics....... 3
General Precautions....................................................... 3
Wet Conditions Maintenance........................................ 3
Introduction..................................................................... 4
Specifications.................................................................. 4
Recommended Tools and Materials.............................. 4
Product Inspection.......................................................... 4
Transmitter Controls....................................................... 5
Transmitter Battery Installation .................................... 5
Battery Charger............................................................... 5
Antenna Tube Installation............................................... 6
Installing the Battery Pack.............................................. 6
Battery Chemistry........................................................... 7
Getting Started................................................................ 7
Range Check.................................................................. 8
Testing Your Boat in the Water....................................... 8
2
When you are Finished.................................................. 9
After Boating and Maintenance.................................. 10
Binding .........................................................................10
Motor Care....................................................................10
Water Cooling System..................................................11
Rudder Service.............................................................11
Prop Angle Adjustment.................................................11
Drivetrain Lubrication................................................... 12
Troubleshooting Guide................................................ 13
Limited Warranty.......................................................... 14
Warranty and Service Contact Information................ 15
FCC and IC Information................................................ 16
Compliance Information for the European Union..... 16
Instructions for Disposal of WEEE............................... 16
Replacement Parts........................................................ 66
Optional Parts............................................................... 66
ShockWave™ 26
EN
Water-resistant Boat with Waterproof Electronics
Your new Horizon Hobby boat has been designed and built with a combination of waterproof and water-resistant
components to allow you to operate the product in calm, fresh water conditions.
While the entire boat is highly water-resistant, it is not completely waterproof and your boat should NOT be treated like
a submarine. The various electronic components used in the boat, such as the Electronic Speed Control (ESC), servo(s)
and receiver are waterproof, however, most of the mechanical components are water-resistant and require additional
maintenance after use.
Metal parts, including the bearings, pins, screws and nuts, propeller, rudder, rudder mounts, prop struts, as well as
the contacts in the electrical cables, will be susceptible to corrosion if additional maintenance is not performed after
running in wet conditions. To maximize the long-term performance of your boat and to keep the warranty intact, the
procedures described in the “Wet Conditions Maintenance” section below must be performed regularly.
CAUTION: Failure to exercise caution while using this product and complying with the following precautions
could result in product malfunction and/or void the warranty.
General Precautions
Wet Conditions Maintenance
• Read through the wet conditions maintenance
procedures and make sure that you have all the tools
you will need to properly maintain your boat.
• Not all batteries can be used in wet conditions.
Consult the battery manufacturer before use. Caution
should be taken when using Li-Po batteries in wet
conditions.
• Most transmitters are not water-resistant. Consult
your transmitter’s manual or the manufacturer before
operation.
• Never operate your transmitter or boat where
lightning may be present.
• Salt water is very conductive and highly corrosive.
If you choose to run your boat in salt water,
immediately rinse the boat in fresh water after every
use. Operating your boat in salt water is at the sole
discretion of the modeler.
• Even minimal water contact can reduce the life of
your motor if it has not been certified as waterresistant or waterproof. If the motor becomes
excessively wet, apply very light throttle until the
water is mostly removed from the motor. Running a
wet motor at high speeds may rapidly damage the
motor.
• Driving in wet conditions can reduce the life of the
motor. The additional resistance of operating in water
causes excess strain.
• Drain any water that has collected in the hull by
removing the drain plug or canopy and tilting the boat
in the appropriate direction to drain the water.
ShockWave™ 26
parts.
CAUTION: Always keep hands, fingers, tools and
any loose or hanging objects away from rotating
• Remove the battery pack(s) and disconnect the
ESC and motor. Dry the contacts. If you have an air
compressor or a can of compressed air, blow out
any water that may be inside the recessed connector
housings.
• Remove the flex shaft and all moving parts. Dry and
lubricate parts after every 30 minutes of operation or
if the boat becomes submerged.
NOTICE: Never use a pressure washer to clean
your boat.
• Use an air compressor or a can of compressed air
to dry the boat and help remove any water that may
have gotten into small crevices or corners.
• Spray the bearings, fasteners and other metal parts
with a water-displacing light oil or lubricant. Do not
spray the motor.
• Let the boat air dry before you store it. Water (and oil)
may continue to drip for a few hours.
3
EN
Introduction
Pro Boat® RC models look as good as they perform. Our boats, which include everything from scale sailboats to
fully licensed powerboats, exceed expectations and provide years of radio control fun and excitement. Whether your
passion leads you towards the pure serenity of sailing or the all-out speed of a Deep-V, Pro Boat models fit your taste,
budget and lifestyle. You can count on us to be available any time you need help—the brand is backed by Horizon
Hobby, one of the world’s largest distributors of hobby-grade RC products. The Pro Boat brand will help you turn your
boating passion into a reality, whether you’re new to the hobby or an old pro.
Please read this manual for operation and maintenance instructions.
Register your boat online at www.proboatmodels.com.
Specifications
Length
26 in (660mm)
Beam (width)
6.85 in (174mm)
Hull Material
Plastic
Motor Dynamite® 2000Kv,
Marine
ESC
Dynamite 30-amp brushless,
water-cooled
Transmitter
ECX® 2.4GHz Transmitter
Receiver
ECX 2.4GHz Receiver,
Water Proof
Batteries
4 AA batteries (sold separately) are required to operate the transmitter.
26 in (660mm)
6.85 in
(174mm)
A battery (sold separately) is required to operate the boat.
The ESC will operate with 2–3 Cell (7.4V–11.1V) Li-Po or
6–9 Cell (7.2V–10.8V) Ni-MH/Ni-Cd batteries.
Recommended Tools and Materials
•
•
•
•
•
•
•
•
•
Needle nose pliers
Paper towel
Rubbing alcohol
Open-end wrench: 10mm (2)
Nut driver: 4mm, 5.5mm, 8mm
Phillips screwdriver: #1
Hex wrench: 1.5mm, 2mm, 2.5mm, 3mm
Clear tape (DYNM0102)
Pro Boat® Marine Grease and Gun
Product Inspection
Carefully remove the boat and radio transmitter from the
box. Inspect the boat for damage.
If you find damage is present, please contact the retailer
where you purchased your boat.
• Hook and Loop Tape Set, WP 4pcs
4
ShockWave™ 26
EN
Transmitter Controls
Battery Level Indicator
Reverse Switch
Solid Red and Green:
Battery voltage is
good (above 4V).
Solid Red: Battery
voltage is critically low
(below 4V). Replace
transmitter batteries.
Throttle Dual Rate
Adjusts the maximum
amount of throttle the
vehicle can be given
Allows you to change the direction of
steering (ST. REV) and throttle (TH. REV)
controls (Ensure proper function with a
radio system test).
Power Switch
Power on or off the transmitter
Steering Dual Rate
Adjusts the amount
the rudder moves
when the steering
wheel is turned
left or right
Steering Wheel
Control steering.
Right and Left
steering
Throttle Trim
Adjusts the neutral
point of the electronic
speed control
Throttle Trigger
Controls power
to the motor
for forward
or reverse
Steering Trim
Adjust to make
the vehicle drive
straight with
no input at the
steering wheel
Reverse
Forward
Stop
Transmitter Battery Installation
This transmitter requires 4 AA batteries.
1. Remove the battery cover from
the transmitter.
2. Install the batteries as shown.
3. Install the battery cover.
Battery Charger
Choose a charger designed to charge the recomended
battery. We recommend either the Dynamite Prophet™
Sport Plus 50W AC/DC Charger or the Dynamite Prophet
Sport Duo 2 X 50W charger. Refer to your charger
manual for charging instructions and safety information.
ShockWave™ 26
NOTICE: Never charge a battery in the boat or damage
may result.
5
EN
Antenna Tube Installation
Install the receiver antenna in the tube as shown.
Keep the end of the antenna above the boat’s
waterline to get the best transmitter reception.
Apply clear tape (DYNM0102), if desired.
NOTICE: Do not cut or kink the
receiver antenna or damage may
result.
Installing the Battery Pack
1. Loosen the 2 screws on the rear of the canopy.
2. Carefully lift the rear of the canopy and pull back to
disengage the 2 front pins from the hull.
3. Install the battery in the compartment. Secure it with
the hook and loop straps. If running your boat in
rougher water conditions, the use of Waterproof Hook
and Loop Tape (DYNK0300) may also be needed to
fully secure the battery.
4. Connect the battery pack to the ESC power
connector.
Tip: Move the packs forward or back to adjust the
center of gravity for your boat. Move the packs toward
the bow so the bow rides lower in the water. Move
the packs away from the bow so that the bow rides
higher in the water.
Trim Tab Adjustment
Tip: Ensure the trim tab panels are either perpendicular
to or parallel to the bottom of the boat.
You may desire to bend the trim tabs for wind and water
conditions. To adjust the angle of the trim tabs, use a
large pair of pliers to bend the tabs. This must be done
carefully so that you do not damage the hull.
6
ShockWave™ 26
EN
Low Voltage Cutoff (LVC)
Battery Chemistry
Discharging a Li-Po battery below 3V per cell may
damage your battery.The included ESC protects the boat
battery from over-discharge using Low Voltage Cutoff
(LVC). Before the battery charge decreases too much,
LVC removes power supplied to the motor. Power to
the motor pulses, showing that some battery power is
reserved for boat control and safe landing.
The ESC comes from the factory in Li-Po Mode. To
change battery chemistry:
Disconnect and remove the Li-Po battery from the boat
after use to prevent trickle discharge. Charge your Li-Po
battery to about half capacity before storage. During
storage, make sure the battery charge does not fall below
3V per cell. LVC does not prevent the battery from overdischarge during storage.
NOTICE: Repeated operation to LVC will damage the
battery.
1. Keep the throttle at neutral and power ON the ESC.
2. Press and hold the Battery Chemistry Button on the
power switch for 3 seconds. The LED flashes the
current battery chemistry (red = Ni-MH or Ni-Cd,
green = Li-Po).
3. Continue holding the Battery Chemistry Button
for another 6 seconds. The ESC changes battery
chemistry and the LED flashes the new battery
chemistry.
4. Power OFF the ESC. The ESC saves the setting until
it is changed.
On/Off Switch
Battery Chemistry
Button
Tip: Monitor your boat battery's voltage before and
after boating by using a Li-Po Cell Voltage Checker
(DYN4071, sold separately).
1
2
Getting Started
1. Power on the transmitter. Ensure the throttle is not
reversed and the throttle trim is neutral.
3
4
2. Connect the battery to the ESC.
3. Keep the throttle at neutral and power ON the ESC.
The ESC automatically calibrates the throttle range
after 3 seconds. A beep will sound, indicating battery
chemistry and cell count:
• 1 beep: Ni-MH or Ni-Cd
• 2 beeps: 2S Li-Po
• 3 beeps: 3S Li-Po
One short beep will sound when the ESC is ready
to run.
4. Test the transmitter’s control of the boat with the
boat on the display stand.
ShockWave™ 26
7
EN
Range Check
IMPORTANT: Perform a range check at the beginning
of each boating session, after repair or after installation
of new batteries.
Ensure the receiver antenna is extended properly and all
batteries are fully charged.
1. With the radio system powered on and connected,
walk away from your boat 90 feet (32 m).
2. Have an assistant remain with the boat to check for
proper control movement of the rudder in response to
your transmitter input.
3. If everything appears to be operating correctly,
prepare to operate the boat in the water.
NOTICE: Do not operate the motor without water
cooling circulation or damage may result.
Testing Your Boat in the Water
Tip: Before placing your boat in the water, secure the
canopy on the hull. Apply clear tape (DYNM0102), if
desired.
1. Carefully place the boat in the water.
2. Operate the boat at slow speeds near the shoreline.
Avoid objects in the water at all times. When the
boat is moving forward, ensure water flows out of
the coolant outlet. Remove any blockage from the
rudder inlet and coolant system or the motor and ESC
(electronic speed control) may overheat.
5. Bring the boat back to shore when you notice the
boat starting to lose speed.
6. Power off the ESC and disconnect the battery pack.
7. Allow the motor, ESC and battery packs to cool before
charging the battery or operating the boat again.
NOTICE: Do not turn off the transmitter first or the
receiver may pick up stray signals and run out of
control.
3. Once you are comfortable operating the boat at slow
speeds, it is safe to operate the boat farther from the
shore.
4. If the boat does not go straight, adjust the steering
trim dial on the transmitter.
Tip: If you are using too much steering trim on your
transmitter to make the boat drive straight, return the
trim to neutral and mechanically center the rudder.
To do this, remove the ball link from the rudder horn,
then turn the ball link on the linkage threads until the
rudder is properly centered. Use needle-nose pliers or
ball link pliers (RVO1005) to remove or install a link on
a control horn.
8
ShockWave™ 26
EN
Boating Tips
When running your boat for the first time, we
recommend calm wind and water conditions so that you
can learn how the boat responds to your control.
If the propeller and rudder are blocked with debris or
vegetation, remove the boat from the water and remove
the debris before continuing operation.
Maximum speeds are only achieved when the water
conditions are smooth and there is little wind. A sharp
turn, wind or waves can turn over a boat when it is
moving quickly. Always pilot your boat for the wind and
water conditions so that the boat does not turn over.
When making turns, decrease the throttle to reduce the
probability of flipping the boat over.
Consult local laws and ordinances before choosing a
location to pilot your boat.
Avoid boating near:
• watercraft
• people (swimming areas, fishing areas)
• stationary objects
Never operate your boat in less than 12 inches (30.5 cm)
of water.
If you need to retrieve your boat from the water, use
fishing equipment or another boat.
NOTICE: When running at full speed in choppy waters,
the prop may exit and re-enter the water repeatedly and
very quickly, subjecting the propeller and flex shaft to
some stress. Frequent stress may damage the propeller
and flex shaft.
CAUTION: Never operate your boat in extreme
temperatures or turbulent water.
• waves, wakes
• rapidly moving water
CAUTION: Never attempt to retrieve a downed
boat by swimming.
• wildlife
• floating debris
• overhanging trees
• vegetation
When you are Finished
1. Power off the receiver.
1
2. Power off the transmitter.
2
3. Disconnect and remove the
battery from the boat.
3
Tip: Always remove the canopy before storage or
moisture may allow mold and mildew to grow in
the boat.
ShockWave™ 26
9
EN
After Boating and Maintenance
• Drain water from inside the hull using the drain plug
• Fully dry the inside and outside of the boat, including
the water cooling lines and jacket around the motor
•
Remove the hatch before storing your boat
NOTICE: When you are finished boating, never leave the
boat in direct sunlight or in a hot, enclosed area such as
a car. Doing so can damage the boat.
• Repair any damage or wear to the boat
• Lubricate the flex shaft using Pro Boat Marine Grease
(PRB0100)
• Make note of lessons learned from the trimming of
your boat, including water and wind conditions
Tip: The hook and loop strips in the boat retain water.
To dry them, press on them with a dry cloth.
Binding
A
Binding is the process of programming the receiver to
recognize the GUID (Globally Unique Identifier) code of a
single specific transmitter. The included transmitter and
receiver are bound at the factory. If you need to rebind,
follow the instructions below.
1. Power off the transmitter and ESC.
2. Connect a fully charged battery pack to the ESC.
3. Power on the ESC. The RED LED on the ESC flashes.
4. Press the bind button (A) on the receiver.
The RED LED on the ESC flashes rapidly.
5. Power on the transmitter.
6. The RED LED on the ESC turns solid when
the radio system is bound.
You must rebind when binding the
receiver to a different transmitter.
NOTICE: Do not attempt to bind the transmitter and
receiver if there are other compatible transmitters in
bind mode within 400 feet. Doing so may result in
unexpected binding.
Failsafe
In the unlikely event that the radio connection is lost
during use, the receiver will drive the servos to their pre
programmed failsafe positions (normally no throttle and
straight steering).
Motor Care
• Prolong motor life by preventing overheating
conditions. Undue motor wear results from frequent
turns, stops and starts, pushing objects, boating in
rough water or vegetation and boating continuously at
high speed.
10
If the receiver is powered on before powering on the
transmitter, the receiver will enter this failsafe mode.
When the transmitter is powered on, normal control is
resumed.
• Over-temperature protection is installed on the ESC to
prevent circuit damage, but cannot protect the motor
from pushing against heavy resistance.
ShockWave™ 26
EN
Water Cooling System
If water does not stream out of the water outlets while
the boat is moving forward, immediately stop the boat
and clean the obstruction from the water cooling system.
1. Disassemble and clean the water cooling system to
remove blockage and prevent overheating.
2. Replace damaged parts.
Rudder Service
1. Disconnect the water tube from the rudder.
2. Remove the linkage from the rudder arm with Ball Link
Pliers.
3. Turn the rudder and loosen the set screw from the
rudder pin.
4. Turn over the boat and lightly tap the rudder to
remove the pin.
5. Assemble in reverse order.
Propeller Service
1. Use an 8mm nut driver (DYN2805) to loosen the nut
from the driveshaft.
2. Remove the nut and propeller from the driveshaft.
3. Assemble in reverse order. Correctly align the
propeller with the drive dog on the driveshaft.
Prop Angle Adjustment
NOTICE: Raise or lower the drive strut small amounts.
Raising or lowering the strut may damage the hull
around the stuffing tube.
Raising the drive strut increases speed, but also
decreases steering response and increases cavitation.
Lowering the drive strut increases steering response, but
also increases steering sensitivity and decreases speed.
1. Loosen the nuts and bolts from the drive strut on the
rear of the boat.
2. Slide the strut up or down to change the angle of the
propeller in relation to the hull.
3. Adjust as desired and tighten the nuts and bolts.
ShockWave™ 26
11
EN
Drivetrain Lubrication
Always replace the drivetrain parts when they are
damaged or show visible wear or injury and damage may
result.
NOTICE: Running the boat in saltwater could cause some
parts to corrode. If you run the boat in saltwater, rinse it
thoroughly in freshwater after each use and lubricate the
drive system.
Lubricating the flex shaft is vital to the life of the
drivetrain. The lubricant also acts as a water seal, keeping
water from entering the hull through the stuffing tube.
NOTICE: Because of its corrosive effects, running RC
boats in saltwater is at the discretion of the modeler.
Lubricate the flex shaft and all moving parts after every
30 minutes of operation. Lubricate the drive strut after
every 90 minutes of operation.
1. In the hull, use a 10mm open-end wrench to loosen
the collet nut from the flex shaft.
2. Slide the flex shaft out from the stuffing tube and
drive strut at the rear of the boat.
Tip: Use paper or cloth to touch the flex shaft and other
lubricated parts.
3. Wipe the old lubricant and material from the flex
shaft.
4. Lubricate the full length of the flex shaft assembly
up to the drive dog using marine grease (PRB0101 or
PRB0100). Also apply grease to the collet threads.
5. Carefully reinstall the flex shaft in the drive strut,
stuffing tube and collet. If the flex shaft is difficult to
remove or install in the collet, use a flat screwdriver to
spread the grips of the collet.
Ensure there is a 1–2mm gap between the drive strut and
drive dog to allow for flex shaft shrinkage under load.
12
ShockWave™ 26
EN
Troubleshooting Guide
Problem
Possible Cause
Solution
Boat will not respond
to throttle but responds
to other controls
Throttle channel is reversed
Reverse throttle channel on transmitter
Damaged propeller, shaft or motor
Replace damaged parts
Propeller is out of balance
Balance or replace propeller
Boat battery charge is low
Completely recharge battery
Boat battery is damaged
Replace boat battery and follow
battery instructions
Extra noise or extra
vibration
Blocking or friction on shaft or propeller
Boat conditions may be too cold
Reduced runtime or
boat underpowered
Boat will not Bind
(during binding) to
transmitter
Boat will not connect
(after binding) to
transmitter
Battery capacity may be too low
for conditions
Replace battery or use a larger capacity battery
Drive dog is too near the prop strut
Loosen motor coupling on flex shaft and move
flex shaft a small amount
Too little lubrication on flex shaft
Fully lubricate flex shaft
Vegetation or other obstacles block
the rudder or propeller
Transmitter is too near boat during
binding process
Boat or transmitter is too close to large
metal object, wireless source or
another transmitter
Another compatible transmitter is
powered on within range of the
receiver
Boat battery/Transmitter battery charge
is too low
ESC switch is off
Transmitter is too near boat during
connecting process
Boat or transmitter is too close to large
metal object, wireless source or another transmitter
Boat battery/transmitter battery charge
is too low
ESC switch is off
Remove vegetation or obstacles from rudder or
propeller
Move powered transmitter a few feet from boat,
disconnect and reconnect battery to boat
The boat hull is not completely closed
Boat tends to dive in
the water or takes on
water
Center of gravity is too far forward
Trim tabs are angled incorrectly
Rudder or rudder trim is not centered
Boat tends to turn one
direction
ShockWave™ 26
Disassemble, lubricate and correctly align parts
Make sure the battery is warm (above 10º C
(50º F)) before use
Vertical fins of trim tabs are angled
incorrectly
Move the boat and transmitter to another location
and attempt binding again
Power off all compatible transmitters
except the one you are trying to bind
Replace/recharge batteries
Power on ESC switch
Move powered transmitter a few feet from boat,
disconnect and reconnect battery to boat
Move boat or transmitter to another location and
attempt to connect again
Replace/recharge batteries
Power on ESC switch
Dry out the boat and ensure the hatch is fully
closed on the hull before returning the boat
to the water
Move batteries back in the hull
Angle each trim tab up a small amount to lift the
bow or down a small amount to lower the bow
Repair rudder or adjust rudder and rudder trim
for straight running when control is at neutral
Angle the fins a small amount right or left so
that the boat goes straight when the rudder
is at neutral
13
EN
Problem
Possible Cause
Solution
Steering servo wire is damaged or
connections are loose
Replace or repair damaged parts and adjust controls
Do a check of steering servo wires and connections, connect or replace as needed
Transmitter is not bound correctly
Re-bind
BEC (Battery Elimination Circuit) of the
ESC is damaged
Replace ESC
ESC switch is off
Power on ESC switch
Controls reversed
Transmitter settings are reversed
Do the Control Direction Test and adjust controls
on transmitter appropriately
Motor overheats
Blocked water cooler tubes
Clean or replace water tubes
ESC uses default soft Low Voltage
Cutoff (LVC)
Recharge boat battery or replace battery that is no
longer performing
Weather conditions might be too cold
Postpone until weather is warmer
Battery is old, worn out or damaged
Replace battery
Rudder, linkage or servo damage
Rudder does not move
Motor power pulses
then motor loses power
LIMITED WARRANTY
What this Warranty Covers
Limitation of Liability
Horizon Hobby, LLC (Horizon) warrants to the original
purchaser that the product purchased (the "Product") will
be free from defects in materials and workmanship at the
date of purchase.
HORIZON SHALL NOT BE LIABLE FOR SPECIAL,
INDIRECT, INCIDENTAL OR CONSEQUENTIAL
DAMAGES, LOSS OF PROFITS OR PRODUCTION OR
COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF
WHETHER SUCH CLAIM IS BASED IN CONTRACT,
WARRANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR
ANY OTHER THEORY OF LIABILITY, EVEN IF HORIZON
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES. Further, in no event shall the liability of
Horizon exceed the individual price of the Product on
which liability is asserted. As Horizon has no control over
use, setup, final assembly, modification or misuse, no
liability shall be assumed nor accepted for any resulting
damage or injury. By the act of use, setup or assembly, the
user accepts all resulting liability. If you as the purchaser or
user are not prepared to accept the liability associated with
the use of the Product, purchaser is advised to return the
Product immediately in new and unused condition to the
place of purchase.
What is Not Covered
This warranty is not transferable and does not cover
(i) cosmetic damage, (ii) damage due to acts of God,
accident, misuse, abuse, negligence, commercial
use, or due to improper use, installation, operation or
maintenance, (iii) modification of or to any part of the
Product, (iv) attempted service by anyone other than a
Horizon Hobby authorized service center, (v) Product
not purchased from an authorized Horizon dealer, or (vi)
Product not compliant with applicable technical regulations.
OTHER THAN THE EXPRESS WARRANTY ABOVE,
HORIZON MAKES NO OTHER WARRANTY OR
REPRESENTATION, AND HEREBY DISCLAIMS ANY AND
ALL IMPLIED WARRANTIES, INCLUDING, WITHOUT
LIMITATION, THE IMPLIED WARRANTIES OF NONINFRINGEMENT, MERCHANTABILITY AND FITNESS
FOR A PARTICULAR PURPOSE. THE PURCHASER
ACKNOWLEDGES THAT THEY ALONE HAVE
DETERMINED THAT THE PRODUCT WILL SUITABLY
MEET THE REQUIREMENTS OF THE PURCHASER’S
INTENDED USE.
Purchaser’s Remedy
Horizon’s sole obligation and purchaser’s sole and
exclusive remedy shall be that Horizon will, at its option,
either (i) service, or (ii) replace, any Product determined
by Horizon to be defective. Horizon reserves the right to
inspect any and all Product(s) involved in a warranty claim.
Service or replacement decisions are at the sole discretion
of Horizon. Proof of purchase is required for all warranty
claims. SERVICE OR REPLACEMENT AS PROVIDED
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE
AND EXCLUSIVE REMEDY.
14
Law
These terms are governed by Illinois law (without regard to
conflict of law principals). This warranty gives you specific
legal rights, and you may also have other rights which vary
from state to state. Horizon reserves the right to change or
modify this warranty at any time without notice.
WARRANTY SERVICES
Questions, Assistance, and Services
Your local hobby store and/or place of purchase cannot
provide warranty support or service. Once assembly, setup
or use of the Product has been started, you must contact
your local distributor or Horizon directly. This will enable
Horizon to better answer your questions and service
you in the event that you may need any assistance. For
questions or assistance, please visit our website at www.
horizonhobby.com, submit a Product Support Inquiry,
or call the toll free telephone number referenced in the
Warranty and Service Contact Information section to speak
with a Product Support representative.
ShockWave™ 26
EN
Inspection or Services
Non-Warranty Service
If this Product needs to be inspected or serviced and is
compliant in the country you live and use the Product in,
please use the Horizon Online Service Request submission
process found on our website or call Horizon to obtain a
Return Merchandise Authorization (RMA) number. Pack
the Product securely using a shipping carton. Please note
that original boxes may be included, but are not designed
to withstand the rigors of shipping without additional
protection. Ship via a carrier that provides tracking and
insurance for lost or damaged parcels, as Horizon is not
responsible for merchandise until it arrives and is accepted
at our facility. An Online Service Request is available
at http://www.horizonhobby.com/content/_servicecenter_render-service-center. If you do not have internet
access, please contact Horizon Product Support to obtain
a RMA number along with instructions for submitting
your product for service. When calling Horizon, you will
be asked to provide your complete name, street address,
email address and phone number where you can be
reached during business hours. When sending product
into Horizon, please include your RMA number, a list of
the included items, and a brief summary of the problem.
A copy of your original sales receipt must be included for
warranty consideration. Be sure your name, address, and
RMA number are clearly written on the outside of the
shipping carton.
Should your service not be covered by warranty, service
will be completed and payment will be required without
notification or estimate of the expense unless the expense
exceeds 50% of the retail purchase cost. By submitting
the item for service you are agreeing to payment of
the service without notification. Service estimates are
available upon request. You must include this request with
your item submitted for service. Non-warranty service
estimates will be billed a minimum of ½ hour of labor.
In addition you will be billed for return freight. Horizon
accepts money orders and cashier’s checks, as well as
Visa, MasterCard, American Express, and Discover cards.
By submitting any item to Horizon for service, you are
agreeing to Horizon’s Terms and Conditions found on our
website http://www.horizonhobby.com/content/_servicecenter_render-service-center.
ATTENTION: Horizon service is limited to Product
compliant in the country of use and ownership.
If received, a non-compliant Product will not be
serviced. Further, the sender will be responsible for
arranging return shipment of the un-serviced Product,
through a carrier of the sender’s choice and at the
sender’s expense. Horizon will hold non-compliant
Product for a period of 60 days from notification, after
which it will be discarded.
NOTICE: Do not ship LiPo batteries to Horizon. If you
have any issue with a LiPo battery, please contact the
appropriate Horizon Product Support office.
Warranty Requirements
For Warranty consideration, you must include your original
sales receipt verifying the proof-of-purchase date. Provided
warranty conditions have been met, your Product will be
serviced or replaced free of charge. Service or replacement
decisions are at the sole discretion of Horizon.
Warranty and Service Contact Information
Country of
Purchase
United States of
America
Horizon Hobby
Contact Information
Horizon Service Center
(Repairs and Repair
Requests)
servicecenter.horizonhobby.
com/RequestForm/
Horizon Product Support
(Product Technical
Assistance)
Sales
United Kingdom
Germany
France
China
ShockWave™ 26
Service/Parts/Sales:
Horizon Hobby Limited
Horizon Technischer
Service
Sales: Horizon Hobby
GmbH
Service/Parts/Sales:
Horizon Hobby SAS
Service/Parts/Sales:
Horizon Hobby – China
www.quickbase.com/db/
bghj7ey8c?a=
GenNewRecord
Address
4105 Fieldstone Rd
Champaign, Illinois, 61822 USA
888-959-2306
sales@horizonhobby.com
888-959-2306
sales@horizonhobby.co.uk
+44 (0) 1279 641 097
service@horizonhobby.de
+49 (0) 4121 2655 100
infofrance@horizonhobby.com
+33 (0) 1 60 18 34 90
info@horizonhobby.com.cn
+86 (021) 5180 9868
Units 1–4 , Ployters Rd, Staple Tye
Harlow, Essex, CM18 7NS, United
Kingdom
Christian-Junge-Straße 1
25337 Elmshorn, Germany
11 Rue Georges Charpak
77127 Lieusaint, France
Room 506, No. 97 Changshou Rd.
Shanghai, China 200060
15
EN
FCC Information
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device
may not cause harmful interference, and (2) this device must accept any interference received, including interference
that may cause undesired operation.
AUTION: Changes or modifications not expressly approved by the party responsible for compliance could
C
void the user’s authority to operate the equipment.
This product contains a radio transmitter with wireless technology which has been tested and found to be compliant
with the applicable regulations governing a radio transmitter in the 2.400GHz to 2.4835GHz frequency range.
IC Information
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including
interference that may cause undesired operation of the device.
Compliance Information for the European Union
Declaration of Conformity
(in accordance with ISO/IEC 17050-1)
No. HH2014071001U1
Product(s):
Item Number(s):
Shockwave 26-inch BL Deep-V RTR
PRB08014
Equipment class:
1
The object of declaration described above is in conformity with the requirements of the specifications listed below,
following the provisions of the European R&TTE Directive 1999/5/EC, EMC Directive 2004/108/EC and LVD Directive
2006/95/EC:
EN 300-328 V1.8.1
EN 301 489-1 V1.9.2: 2012
EN 301 489-17 V2.1.1: 2009
EN 62311: 2008
EN 60950-1:2006+A11:2009+A1:2010+A12: 2011
EN 55022:2010 + AC:2011
EN 55024:2010
Signed for and on behalf of:
Horizon Hobby, LLC
Champaign, IL USA
October 27, 2014
Instructions
Mike Dunne
Executive Vice President Product Divisions, Horizon Hobby, LLC
for Disposal of WEEE by Users in the European Union
This product must not be disposed of with other waste. Instead, it is the user’s responsibility to dispose of their
waste equipment by handing it over to a designated collection point for the recycling of waste electrical and electronic
equipment. The separate collection and recycling of your waste equipment at the time of disposal will help to conserve
natural resources and ensure that it is recycled in a manner that protects human health and the environment. For more
information about where you can drop off your waste equipment for recycling, please contact your local city office,
your household waste disposal service or where you purchased the product.
16
ShockWave™ 26
IT
Replacement Parts / Ersatzteile / Pièces de rechange / Pezzi di ricambio
Part #
Français
Coque avec décoration
Italiano
Scafo e adesivi:
Shockwave 26 V3
Cockpit avec décoration
Capottina e adesivi:
Shockwave 26 V3
Gouvernail avec son
support
Timone e suo supporto:
BJ24 & SW26 V3
Pinne di virata e Trim
di assetto: Shockwave
26 V3
Piede elica: Blackjack
24 & Shockwave 26 V3
Albero flex,
trascinatore, guida: BJ
24, SW26 V3
Elica: 1.34" x 2.06"
Adattatore motore per
albero da 5mm
S6170 Std Digitale per
auto SX
30A Brushless Marine
ESC: batteria singola
2000kv Motor
brushless
ECX 2.4GHz Ricevitore
impermeabile
ECX 2.4GHz
Trasmettitore 2 canali
PRB281011
Deutsch
Shockwave 26 V3:
Rumpf u. Dekorbogen
Shockwave
26 V3:
Canopy and Decals:
abinenhaube u.
Shockwave 26 V3
Dekorbogen
Rudder & Rudder Mount: Blackjack 24: Ruder u.
BJ24 & SW26 V3
Ruderhalter
PRB281014
Turn Fins & Trim Tabs:
Shockwave 26 V3
Shockwave 26 V3:
Turnfins u. Trimmbleche
Dérives et stabilisateurs
PRB286009
Prop Strut: Blackjack 24
& Shockwave 26 V3
Flex Shaft, Drive Dog,
Liner 290mm: BJ 24,
SW26 V3
Propeller: 1.34" x 2.06"
Motor Coupler: 5mm
motor shaft
S6170 Std Digital
Surface Sx
30A Brushless Marine
ESC: Single Battery
Blackjack 24: Propstrebe
Chaise d'hélice
Blackjack 24: Flexwelle,
Mitnehmer, Dichtung
Flexible/gaine 290mm/
entraîneur
PRB281012
PRB281013
PRB282009
PRB282008
PRB286010
SPMSS6170
DYNM3860
DYNM3900
ECX9011
ECX9010
English
Hull and Decals:
Shockwave 26 V3
1.34" x 2.06"
Hélice 1.34" x 2.06"
Accouplement
moteur
Kupplung 5mm Welle
5mm
S6170 Standard Digital
Servo S6170 Standard
Surface Servo
digital
Dynamite 30A BL
Contrôleur brushless
Marine Regler ESC 3-3S 30A Simple batterie
3650 4 Pole
Moteur brushless
2000kv Brushless motor Dynamite
BL Marine Motor 2000kv 2000Kv
ECX 2.4GHz Receiver,
ECX Empfänger
Récepteur ECX 2.4Ghz
Water Proof
wasserfest 2.4Ghz
étanche
ECX 2.4GHz Transmitter, ECX Coltsender 2 Kanal Emetteur ECX 2.4GHz
2-Chan
2.4Ghz
2 voies
Optional Parts / Diverse Teile / Pièces optionnelles / Pezzi opzionali
Part #
English
Deutsch
Français
DYN2801
4mm Nut Driver
Steckschlüssel l 4mm
Clé à écrou 4mm
Italiano
Chiave a tubo 4mm
DYN2803
5.5mm Nut Driver
Steckschlüssel 5.5mm
Clé à écrou 5.5mm
Chiave a tubo 5,5mm
DYN2805
8mm Nut Driver
Steckschlüssel 8mm
Clé à écrou 8mm
DYN2819
Hex Wrench 1.5mm,
2mm, 2.5mm, 3mm
Inbuschlüsselsatz 1.54mm 5Stk metrisch
Clés BTR 1.5mm, 2mm,
2.5mm et 3mm
Chiave a tubo 8mm
Chiavetta esagonale
1.5mm, 2mm,
2.5mm, 3mm
Cacciavite Phillips: #1
DYN2828
Phillips screwdriver: #1
Schraubenzieher Kreuz #1
Tournevis cruciforme #1
DYN4071
Cell Voltage Checker
Reaction 7.4V 5000mAh
2S 50C LiPo, Hardcase:
EC5
LiPo Cell Volt- Checker
Reaction 7.4V 5000mAh
2S 50C LiPo, Hardcase:
EC5
Contrôleur de tension
Batterie Reaction Li-PO
2S 7.4V 5000mA 50C,
coque rigide, prise EC5
DYNB3811EC
Reaction 11.1V
5000mAh 3S 50C LiPo,
Hardcase: EC5
Reaction 11.1V
5000mAh 3S 50C LiPo,
Hardcase: EC5
Batterie Reaction Li-PO
3S 11.1V 5000mA 50C,
coque rigide, prise EC5
DYNC0029
EC5 Device To EC3
Battery
Dynamite Adapter EC5
Stecker auf EC3 Buchse
Adaptateur Prise EC5
contrôleur vers EC3
batterie
Voltmetro celle
Reaction 7.4V
5000mAh 2S 50C
contenitore rigido: EC5
Batteria LiPo Reaction
11.1V 5000mAh 3S
50C contenitore rigido:
EC5
Adattatore
dispositivo EC5 a
batteria EC3
Prophet Sport Plus 50W
AC/DC Charger
Chargeur Prophet Sport
Plus 50W AC/DC
Caricatore Prophet
Sport Plus 50W AC/DC
Chargeur Prophet Sport
Duo 50Wx2 AC
Caricabatterie
Prophet Sport Duo
50Wx2 AC
Bande auto-agrippante
adhésive, résistante à
l'eau (4pcs)
Adhésif transparent
résistant à l'eau
Set nastro a
strappo, WP 4pcs
DYNB3810EC
DYNC2010CA,
DYNC2010EU,
DYNC2010UK
DYNC2020,
DYNC2020EU,
DYNC2020UK,
Prophet Sport Duo
50Wx2 AC Battery
Charger
Dynamite Ladegerät
Prophet Sport Plus 50W
AC/DC EU
Dynamite Prophet
Sport Duo 50Wx2 AC
Ladegerät, EU
DYNK0300
Hook and Loop Tape
Set, WP 4pcs
Dynamite Klettband Set
75x25 4 Stk
DYNM0102
waterproof tape
PRB0100
Marine Grease
Dynamite transparentes
Marineklebeband (18m)
Proboat Marine Fett m.
Applikator 5 oz
Revolution Deluxe
Kugelkopfzange
RVO1005
62
Ball Link Pliers
Nastro impermeabile
Graisse marine
Grasso marino
Pince à chapes rotules
Pinza per attacchi a
sfera
ShockWave™ 26
44714.1 Revised: 11/2014
©2015 Horizon Hobby, LLC.
Pro Boat, the Pro Boat logo, ShockWave, Dynamite, ECX, Reaction, Prophet, EC3, EC5 and the Horizon
Hobby logo are trademarks or registered trademarks of Horizon Hobby, LLC.
The Spektrum trademark is used with permission of Bachmann Industries, Inc.
PRB08014
Download PDF