SE-SW5U 5-Port Ethernet Switch Technical Specs

SE-SW5U 5-Port Ethernet Switch Technical Specs
Prices as of April 16, 2014. Check Web site for most current prices.
Stride Unmanaged Industrial Ethernet
Switches
®
5-Port Ethernet Switch - Plastic Case
STRIDE SlimLine Industrial Unmanaged Ethernet Switch, plastic case, -10 to +60 °C
operating temperature range, five 10/100BaseT RJ45 Ethernet ports. Redundant power
inputs with surge and spike protection, auto-crossover, DIN rail mounting. Supports Store
and Forward wire speed switching and full-duplex with flow control. UL/CUL1604 (Class
I, Div. 2, Groups A, B, C, D) and CE marked.
Dimensions
Inches [mm]
5 Port – SE-SW5U
Removable
Screw Block,
Phoenix
p/n 1757035
Snaps to standard
35 mm x 7.5 mm height
DIN rail (EN50022)
1.01
[25.7]
4.35
[110.5]
3.96
[100.6]
1.98
[50.3]
Dia. 0.15 [3.8]
Use for direct
panel mounting
to a flat surface.
1.01
[25.7]
SE-SW5U
$99.00
0.06
[1.5]
3.26
[82.8]
1.00
[25.4]
1.98
[50.3]
ACT/LNK LED
Speed 10/100 LED
Specifications
This is the Yellow LED on models with a
Yellow and a Green LED per RJ45 port.
This is the Green LED on models with a
Yellow and a Green LED per RJ45 port.
The following are specifications relevant
to the SE-SW5U 5-Port Ethernet Switch.
Indicates that there is a proper Ethernet
ON (yellow) connection (Link) between the port
(not flashing) and another Ethernet device, but no
communications activity is detected.
ON (yellow)
(flashing)
Indicates that there is a proper Ethernet
connection (Link) between the port and
another Ethernet device, and that there
is communications activity.
OFF
Indicates that there is not a proper
Ethernet connection (Link) between
the port and another Ethernet device.
Make sure the cable has been plugged
securely into the ports at both ends.
ON (green)
A 100 Mbps (100BaseT) connection
is detected.
OFF
A 10 Mbps (10BaseT) connection is
detected.
Input power (typical
with all ports active
at 100 Mbps)
Weight
Power connector
max. screw torque
2.0 W
4 oz (0.11 kg)
5.0 lb-in (0.57 Nm)
Book 1 (14.1)
eCM-24
Communication Products
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Stride Unmanaged Industrial Ethernet
Switches & Media Converter
®
General Specifications
Up to 9 ports
Ethernet switch type
Store and forward wire speed switching, non-blocking
Operating mode
All IEEE 802.3 compliant devices are supported
Devices supported
IEEE 802.3, 802.3u, 802.3x
Standards
1024 addresses
MAC addresses
3.2 Gbps
Memory bandwidth
16 us + frame time (typical)
Latency for 10 Mbps ports
5 us + frame time (typical)
Latency for 100 Mbps ports
Redundant Input Terminals
Power input
Input power
(typical with all ports
active at 100 Mbps)
Input voltage
Reverse power protection
Transient protection
Spike protection
Ethernet isolation
Operating temperature
range
Storage temperature range
Humidity (non-condensing)
Environmental Air
Vibration, shock & freefall
Agency Approvals
EMI emissions
EMC immunity
RoHS and WEEE
Environmental Air
SE-MC2U-ST
SE-MC2U-SC
2.0 W
SE-SW5U
SE-SW5U-WT
SE-SW5U-ST
SE-SW5U-SC
3.0 W
SE-SW5U-ST-WT
SE-SW5U-SC-WT
SE-SW8U
4.0 W
SE-SW8U-WT
SE-SW9U-ST
SE-SW9U-SC
5.0 W
SE-SW9U-ST-WT
SE-SW9U-ST-WC
10-30 VDC (continuous) - Class 2 Power Supply
Yes
15,000 watts peak
5,000 watts (10x for 10 uS)
1500 VRMS 1 minute
SE-MC2U-ST
SE-MC2U-SC
SE-SW5U
-10 to +60 °C (+14 to +140 °F),
SE-SW8U
cold startup at -10 °C (+14 °F)
SE-SW5U-ST
SE-SW5U-SC
SE-SW9U-ST
SE-SW9U-SC
SE-SW5U-WT
SE-SW8U-WT
-40 to +85 °C (-40 to +185 °F),
SE-SW5U-ST-WT
cold startup at -40 °C (-40 °F)
SE-SW5U-SC-WT
SE-SW9U-ST-WT
SE-SW9U-SC-WT
-40 to +85 °C (-40 to +185 °F)
5 to 95% RH
No corrosive gasses permitted
IEC68-2-6, -27, -32
UL/cUL 508, CSA C22 per EN61010-1,
UL/cUL 1604 (Class 1, Div. 2, Groups A, B, C, D),
CSA C 22.2/213 9 per EN50021/EN60079-15
(Zone 2, Category 3), CE (ATEX)
FCC part 15, ICES-003, EN55022
IEC61326-1
RoHS (Pb free) and WEEE compliant
For use in Pollution Degree 2 environment
General Specifications Cont’d
Packaging and
protection
Dimensions (L x W x H)
SE-MC2U-ST
SE-MC2U-SC
SE-SW5U
SE-SW8U
UL94VO Lexan, IP30
SE-SW5U-ST
SE-SW5U-SC
SE-SW9U-ST
SE-SW9U-SC
SE-SW5U-WT
SE-SW8U-WT
SE-SW5U-ST-WT
Aluminum IP30
SE-SW5U-SC-WT
SE-SW9U-ST-WT
SE-SW9U-SC-WT
See mechanical diagrams for details
Copper RJ45 Ports: (10/100BaseT)
10/100BaseT ports
Protocols supported
Ethernet compliancy
Auto-crossover
Auto-sensing operation
Auto-negotiating
Auto-polarity
Flow control
Ethernet isolation
Plug and play
Cable requirements
Max. cable distance
Shielded RJ45
All standard IEEE 802.3
IEEE 802.3, 802.3u, 802.3x
Yes, allows you to use straight-through or crossover wired
cables
Yes, Full and half duplex
Yes, 10BaseT and 100BaseT
Yes, on the TD and RD pair
Automatic
1500 VRMS 1 minute
Yes
Twisted pair (Cat. 5 or better) (shielded recommended)
100 meters
Fiber Port: (100BaseFX multimode)
100BaseFX ports
Fiber port mode
Fiber port connector
Optimal fiber cable
Center wavelength
Multimode
Nominal max. distance
(full duplex)
Half and full duplex
Ethernet compliance
Eye safety (laser)
1
Multimode (mm)
ST – models SE-XXXX-ST and SE-XXXX-ST-WT
SC – models SE-XXXX-SC and SE-XXXX-SC-WT
50/125 or 62.5/125 µm
1300 nm
Links up to 4 km typ.; 1300 nm;
use with 50 or 62.5/125 um fiber
> Transmitter power (dB): -21 min, -17 typ, -14 max
> Receiver sensitivity (dB): -34 typ, -31 max
4 km
Full duplex
100BaseFX
IEC 60825-1, Class 1; FDA 21 CFR 1040.10 and 1040.11
Complete documentation
Documentation can be downloaded from
www.automationdirect.com.
Book 1 (14.1)
eCM-22
Communication Products
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Unmanaged Industrial Ethernet
Switches & Media Converter
®
Company
Information
Control Systems
Overview
Installation
CLICK PLC
DIN Rail Mounting: Plastic Case
DIN Rail Mounting: Metal Case
DIN rail mounting steps:
1. H
ook top back of unit over the DIN rail.
2. P ush bottom back onto the DIN rail until it snaps into place.
DIN rail removal steps:
A. Insert screwdriver into DIN clip and pry until it releases from
the DIN rail.
B. Unhook top of unit from DIN rail.
DIN rail mounting steps:
1. Hook top back of unit over the DIN rail.
2. Push bottom back onto the DIN rail until it snaps into place.
DIN rail removal steps:
A. Push the unit down to free the bottom of the DIN rail.
B. Rotate the bottom of the unit away from the DIN rail.
C. Unhook top of unit from DIN rail.
Mounting
Mounting
Removal
Do-More
PLCs Overview
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
Removal
DirectLOGIC
DL105
B
1
1
C
DirectLOGIC
DL205
A
DirectLOGIC
DL305
B
2
DirectLOGIC
DL405
2
Productivity
Controller
Overview
A
Productivity
3000
Optional Mounting
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Vertical screw to panel mount.
Flat screw to panel mount.
For better shock and vibration resistance
(Metal cased models only)
For a low profile orientation in shallow boxes plus the best shock
and vibration resistance.
Power wiring
ST or SC Fiber Connector
Maximum power
terminal screw
torque is
5.0 lb-in (0.57Nm).
P2 P1
+ –
One DC Supply
Chassis
GND
(panel)
Wire Size Range
24 – 12 AWG
10-30 VDC
Terms and
Conditions
P2 P1
+ –
+ –
Chassis
GND
(panel)
Dual DC Supplies
A recommended DC power supply is
AutomationDirect.com Part number PSC-24-015.
The power connection terminal block is
removable for access to the mounting tab.
www.automationdirect.com/communications
Communications
Appendix
Book 1
Redundant DC Power
Single DC Power
Other HMI
ST type
Connector
SC type
Connector
Book 1 (14.1)
Communication Products
eCM-23
Prices as of April 16, 2014. Check Web site for most current prices.
Stride Unmanaged Industrial Ethernet
Switches & Media Converter
®
Unmanaged Switches offer
Deterministic Control
Increased Reliability
The Stride unmanaged switches automatically determine and
remember where each Ethernet device is located and route
messages only through the appropriate port. This gives devices on
the network an open communications channels and helps minimizes network loading. Another benefit is the 10/100 auto-speed
selection that enhances the performance of 10 Mpbs Ethernet
devices by speeding up their message transmissions to 100 Mbps
when they are passed to a faster Ethernet backbone.
The Stride Ethernet switches have been designed for the industrial
environment. They will survive extreme temperatures, as well as
dirty, unreliable industrial power. Meeting UL 1604 (Class I Div.
2), and the IEC68-2 standard for vibration resilience, the Stride
switches will provide years of reliable performance in applications
too tough for commercial grade switches.
Simple Installation
With no user setup required, the Stride unmanaged switches and
media converters will immediately start operating as soon as you
power them up and connect them to the network.
Unmanaged Switches
Mounting Options: Snaps to standard
35mm x 7.5mm height DIN rail (EN50022).
The (-WT) metal housing versions also
offer various mounting options.
Fiber LED to indicate a proper connection
for the fiber connectors and network
activity.
Fiber Optic Port on selected
models. Multi-mode fiber optic
port with ST or SC type connector
that supports half and full duplex
with a maximum distance of 4km.
Activity, Link and Speed LEDs
are integrated into the RJ45 ports.
RJ45 Ports that are fully IEEE 802.3
compliant with 10/100 autodetecting for speed and duplex
(full or half).
Auto crossover (MDI/MDIX)
automatically supports either
straight or crossed cables
which greatly reduces cable
installation errors.
Book 1 (14.1)
eCM-20
Redundant Power Inputs
Dual power inputs with industrial surge
and spike protection help reduce down
time when there is primary power loss.
Reverse power protection is also
supported.
Power LED to indicate power
on P1 or P2 power inputs.
DIN Rail Mount
Snaps to standard 35mm x 7.5mm
height DIN rail (EN50022).
Industrial Temperature Ranges
Plastic Models:
-10 to +60 °C (+14 to +140 °F) operating
temperature range
Metal Models (-WT):
-40 to +85 °C (-40 to +185 °F) operating
temperature range. 5 to 95% RH humidity
range (non-condensing).
Agency Approvals:
UL1604, CSA C22.2/213 (Class I, Div.2)
EN50021/EN60079-15
Model SE-SW5U-ST-WT shown above. For detailed specifications on all models, see following pages
Communication Products
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Switches and Media Converter
Company
Information
Control Systems
Overview
®
CLICK PLC
Performance and Quality
Managed Models
Starting at $445
Do-More
PLCs Overview
Unmanaged Models
Starting at $99
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL105
DirectLOGIC
DL205
DirectLOGIC
DL305
Metal Models (-WT)
Starting at $199
Gigabit Ethernet
(on select models)
Industrial Strength Ethernet
Stride is our line of managed and unmanaged industrial grade Ethernet
switches and media converters. Designed with our PLC, HMI and
drive customers in mind, Stride Ethernet switches are specifically built
for industrial environments. With a Stride industrial Ethernet switch on an
isolated control LAN, you can reduce data collisions that slow down your
network. Stride Ethernet switches automatically determine and remember
the devices connected to each port and route messages only through
the appropriate ports. Install Stride switches and your Ethernet control
network will maintain more consistent cycle times even under heavy I/O
and data exchange.
Features
Extreme Temperatures
For industrial applications where temperatures can change from
freezing to sweltering heat, the Stride line offers Ethernet switches that
are designed for standard industrial environments, as well as the most
extreme industrial environments. The rugged metal housing switch
models offer superior EMC performance and corrosion-resistance while
also allowing you to choose various mounting methods for your application. This is standard and no kits are required!
Productivity
Controller
Overview
Productivity
3000
Advanced Hardware
-All 10/100/1000 RJ45 ports are auto-detecting,
auto-crossover and auto-polarity.
-Redundant power inputs with industrial
surge and spike protection
-Fiber optic ports available on certain models
- SFP transceiver modules on selected models offer
additional fiber options
Universal
Field I/O
Real-time Performace
-Store and Forward wire speed switching - no delays
-Full-duplex operation with flow control
(no collisions!)
-Auto crossover (MDI/MDIX) and auto polarity
ViewMarq
Industrial
Marquees
True Industrial Design
- Ethernet Isolation -1500 VRMS 1 minute
- Spike protection - 5,000 watts (10x for 10 uS)
- UL, (cUL) listed and CE certified
- Hazardous locations rated for Class 1, Div. 2
- Rugged heavy-gauge Aluminum case available
Fiber Optic Support
Stride offers models with a variety of Fiber Optic connections. Fiber optic
cables are immune to electrical and magnetic interference and cannot
be damaged by induced voltage transients. Fiber optic cabling not only
enhances reliability, it saves time you might have spent tracking down
those nasty communications problems caused by electrical interference.
Also, your network distance is greatly increased when using Fiber optic
cabling.
www.automationdirect.com/communications
DirectLOGIC
DL405
Book 1 (14.1)
Communication Products
eCM-3
Software
C-More
HMI
C-More Micro
HMI
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
Prices as of April 16, 2014. Check Web site for most current prices.
Industrial Ethernet Switches
& Media Converter
®
Stride Managed Ethernet Switches
As the use of industrial Ethernet devices increases, network
security, segment isolation, and packet priority control become
increasingly difficult when using unmanaged switches. This is
where the Stride managed switch becomes especially beneficial
in an industrial network application. Supported features such
as SNMP, IGMP, VLAN, QOS and network redundancy, allow
networks to be configured and managed in a way that assures
the highest performance levels for your application.
The Stride Managed Ethernet switches allow you to design and
build reliable, rugged and cost effective networks with a switch
that will survive extreme temperatures, as well as dirty, unreliable industrial power. Meeting UL 1604 (Class I Div. 2), and the
IEC68-2 standard for vibration resilience, the Stride switches will
provide years of reliable performance in applications too tough
for commercial grade switches.
Our managed switches offer Gigabit and fast Ethernet options,
as well as various fiber SFP transceiver modules that can be used
on select models. Just take a look at some of the key features
that separate Stride the from the rest of the pack:
Managed Switches
Mounting Options: Supports DIN-rail
and side mounting.
Redundant Dual Power Inputs with
industrial surge and spike protection
help reduce down time when there is
primary power loss. Reverse power
protection is also supported.
Activity, Link and Speed LEDs are
integrated into the RJ45 ports.
Fiber Optic Port on selected
models with ST or SC type connector that
supports half and full duplex. SFP module
options for distances up to 30Km.
Fiber LED to indicate a proper connection for the fiber connectors and
network activity. (on models with SFP
or Fiber ports).
RJ45 Ports that are fully IEEE 802.3
compliant with 10/100 autodetecting for speed and duplex
(10/100/1000 on selected Gigabit
switch models).
Auto crossover (MDI/MDIX)
automatically supports either straight
or crossed cables which greatly
reduces cable installation errors.
Power LED to indicate power
on P1 or P2 power inputs.
Flexible Console Connections
2 Console Ports (USB & RS-232) for
convenience.
All Metal Case provides sturdy protection and is designed to remove exccess
heat from components; offers superior
EMC performance.
Industrial Temperature Range
-40 to +75 °C (-40 to +165 °F) operating
temperature range. 5 to 95% RH
humidity range (non-condensing).
Agency Approvals:
UL1604, CSA C22.2/213 (Class I, Div.2)
EN50021/EN60079-15
SFP Option Modules: STRIDE SFP (small form-factor pluggable) transceivers, also
called mini- GBIC, are compact, hot-swappable transceivers with LC fiber connectors.
The Stride SE-SW8MG-4P and SE-SW10MG-2P switches have ports that accept these
optional transceivers to add fiber connectivity at Fast Ethernet or Gigabit Ethernet speed.
There are several models to choose, ranging from 550 meters to 30Km.
Model SE-SW8MG-4P shown above. For detailed specifications on all models, see following pages
Book 1 (14.1)
eCM-4
Communication Products
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Patch Cables
Cat5e STP Ethernet Patch Cables
Connectivity
Ethernet is a multi-purpose communication protocol that
has become the data standard for the industrial market.
AutomationDirect offers several PLC’s, HMI’s and drives that
support the Ethernet Protocols for data distribution, software
programming and configuration.
Designed for Industrial Use
The noise interference radiated from electrical components that
is often associated with factory floor environments can result
in partial or complete data loss. This may result in delays or
complete communication loss in extremely noisy environments.
Our Ethernet patch cables are designed to reduce the effects
of (EMI) electromagnetic interference by incorporating a single
metal foil shield that wraps around the entire set of 8 wires in
the Cat5e cable. The RJ45 connectors are also shielded against
electrical interference and designed to be robust. Our 350
MHz cables exceed all Cat5e TIA/EIA standards, and drastically
reduce both impedance and structural return loss (SRL) when
compared to standard 100 MHz cables.
RoHS
RoHS Compliant
Features
With several colors and lengths to choose from at great pricing,
these cables should help you in creating solid, reliable Ethernet
networks with any application.
• Connector; 50-micron gold plated RJ45 male plugs
• Conductor; 4-pair 24 AWG stranded copper
• Overall foil shielded cable for industrial applications
• Crossover cables have “crossover” label on each end.
• Exceeds Category 5e specifications, 350MHz
• Multiple lengths and colors
• CM rated, suitable for general use other than plenum spaces
• RoHS compliant
24AWG
Drain
Crossover Cable
1
2
3
4
5
6
7
8
RJ45
OR/WHT
GRN/WHT
OR
GRN
GRN/WHT
OR/WHT
BLU
BLU/WHT
BLU
BLU/WHT
GRN
BRN/WHT
OR
BRN/WHT
BRN
BRN
DRAIN
1
2
3
4
5
6
7
8
RJ45
shield
Patch (Straight-through) Cable
1
2
3
4
5
6
7
8
RJ45
OR/WHT
OR/WHT
OR
GRN/WHT
OR
GRN/WHT
BLU
BLU/WHT
BLU
BLU/WHT
GRN
BRN/WHT
GRN
BRN/WHT
BRN
DRAIN
shield
BRN
DRAIN
1
2
3
4
5
6
7
8
RJ45
Mylar
Separator
12345678
Foil Shield
8-pin RJ45 Connector
Ø 6.0 +/-.15mm
PVC
Jacket
Book 1 (14.1)
eCM-44
Communication Products
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Patch Cables
Company
Information
Control Systems
Overview
Straight Through Patch Cables
Part Number
C5E-STPGY-S3
C5E-STPBK-S3
C5E-STPBL-S3
C5E-STPGN-S3
C5E-STPPL-S3
C5E-STPRD-S3
C5E-STPYL-S3
C5E-STPOR-S3
C5E-STPGY-S7
C5E-STPBK-S7
C5E-STPBL-S7
C5E-STPGN-S7
C5E-STPPL-S7
C5E-STPRD-S7
C5E-STPYL-S7
C5E-STPOR-S7
C5E-STPGY-S10
C5E-STPBK-S10
C5E-STPBL-S10
C5E-STPGN-S10
C5E-STPPL-S10
C5E-STPRD-S10
C5E-STPYL-S10
C5E-STPOR-S10
C5E-STPGY-S14
C5E-STPBK-S14
C5E-STPBL-S14
C5E-STPGN-S14
C5E-STPPL-S14
C5E-STPRD-S14
C5E-STPYL-S14
C5E-STPOR-S14
C5E-STPGY-S25
C5E-STPBK-S25
C5E-STPBL-S25
C5E-STPGN-S25
C5E-STPPL-S25
C5E-STPRD-S25
C5E-STPYL-S25
C5E-STPOR-S25
C5E-STPGY-S50
C5E-STPBK-S50
C5E-STPBL-S50
C5E-STPGN-S50
C5E-STPPL-S50
C5E-STPRD-S50
C5E-STPYL-S50
C5E-STPOR-S50
Color
Description
Length
Price
CLICK PLC
Gray
$4.50
Black
$4.50
Blue
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
3 ft. (0.9m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz,
4-pair 24 AWG stranded copper. Can support 10 / 100 / 1000 Mbps;
exceeds Category 5e cable specifications.
$4.50
3’ (0.91 m)
$4.50
$4.50
$4.50
Yellow
$4.50
Orange
$4.50
Gray
$6.75
Black
$6.75
Blue
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
7 ft. (2.1m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz,
4-pair 24 AWG stranded copper. Can support 10 / 100 / 1000 Mbps;
exceeds Category 5e cable specifications.
$6.75
7’ (2.13 m)
$6.75
$6.75
$6.75
Yellow
$6.75
Orange
$6.75
Gray
$8.50
Black
$8.50
Blue
$8.50
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
10 ft. (3.0m) length, PVC cable jacket. RJ-45 male connectors,
350 MHz, 4-pair 24 AWG stranded copper. Can support
10 / 100 / 1000 Mbps; exceeds Category 5e cable specifications.
10’ (3.05 m)
$8.50
$8.50
$8.50
Yellow
$8.50
Orange
$8.50
Gray
$10.00
Black
$10.00
Blue
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
14 ft. (4.3m) length, PVC cable jacket. RJ-45 male connectors,
350 MHz, 4-pair 24 AWG stranded copper. Can support
10 / 100 / 1000 Mbps; exceeds Category 5e cable specifications.
$10.00
14’ (4.3 m)
$10.00
$10.00
$10.00
Yellow
$10.00
Orange
$10.00
Gray
$14.50
Black
$14.50
Blue
$14.50
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
25 ft. (7.5m) length, PVC cable jacket. RJ-45 male connectors,
350 MHz, 4-pair 24 AWG stranded copper. Can support
10 / 100 / 1000 Mbps; exceeds Category 5e cable specifications.
25’ (7.6 m)
$14.50
$14.50
$14.50
Yellow
$14.50
Orange
$14.50
Gray
$24.50
Black
$24.50
Blue
$24.50
Green
Purple
Red
Ethernet patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
50 ft. (15.2m) length, PVC cable jacket. RJ-45 male connectors,
350 MHz, 4-pair 24 AWG stranded copper. Can support
10 / 100 / 1000 Mbps; exceeds Category 5e cable specifications.
50’ (15.2 m)
$24.50
$24.50
$24.50
Yellow
$24.50
Orange
$24.50
www.automationdirect.com/communications
Book 1 (14.1)
Communication Products
eCM-45
Do-More
PLCs Overview
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL105
DirectLOGIC
DL205
DirectLOGIC
DL305
DirectLOGIC
DL405
Productivity
Controller
Overview
Productivity
3000
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Patch Cables
Crossover Patch Cables
Part Number
C5E-STPYL-C3
Color
Description
Yellow
C5E-STPOR-C3
Orange
C5E-STPYL-C7
Yellow
C5E-STPOR-C7
Orange
C5E-STPYL-C10
Yellow
C5E-STPOR-C10
Orange
C5E-STPYL-C14
Yellow
C5E-STPOR-C14
Orange
C5E-STPYL-C25
Yellow
C5E-STPOR-C25
Orange
C5E-STPYL-C50
Yellow
C5E-STPOR-C50
Orange
Length
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
3 ft. (0.9m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
3’ (0.91 m)
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
7ft (2.1m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
7’ (2.13 m)
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
10ft (3.0m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
10’ (3.05 m)
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
14ft (4.3m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
14’ (4.3 m)
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
25ft (7.5m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
25’ (7.6 m)
Ethernet crossover patch cable, Cat5e STP (Twisted Pairs with overall foil Shield),
50ft (15.2m) length, PVC cable jacket. RJ-45 male connectors, 350 MHz, 4-pair 24 AWG
stranded copper; labeled as “Crossover” on both ends. Can support 10 / 100 / 1000
Mbps; exceeds Category 5e cable specifications.
50’ (15.2 m)
Price
$5.25
$5.25
$7.50
$7.50
$9.00
$9.00
$11.00
$11.00
$15.00
$15.00
$25.50
$25.50
Book 1 (14.1)
eCM-46
Communication Products
1-800-633-0405
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement