Series 608 Differential Pressure Transmitter Specifications - Installation and Operating Instructions

Series 608 Differential Pressure Transmitter Specifications - Installation and Operating Instructions
E-60
8/18/05
8:55 AM
Page 1
Bulletin E-60
Series 608 Differential Pressure Transmitter
Specifications - Installation and Operating Instructions
1/4
[6.35]
3-1/4
[82.55]
4-1/2
[107.95]
5-1/32
[127.79]
1/2 NPT
TYP 2 PLACES
2-11/16
[68.26]
3
[76.20]
5/8
[15.88]
1-1/2
[38.10]
1/4 NPT
TYP 2 PLACES
The Dwyer Series 608 Differential Pressure Transmitter converts positive, negative (vacuum), or differential pressures of clean,
dry air or other non-conductive, non-corrosive gases into a standard two wire, 4-20 mA output signal. Several factory calibrated
models are available with ranges from 0-0.1˝ (0-2.5 mm) w.c. up
to 0-25˝ (0-634.4 mm) w.c. All models employ a variable capacitance transducer with a micro-machined, ultra thin silicon
diaphragm enabling precision measurement and control of very
low differential pressures while withstanding a high static working
pressure of 100 psig (6.89 bar). The Series 608 is FM approved
intrinsically safe for use in the specified hazardous locations when
used with an approved intrinsic safety barrier. It also features a
NEMA 4X enclosure that allows for indoor and outdoor installations. This rugged housing design makes this transmitter ideal for
use in industrial and process plant environments.
INSTALLATION
1. Location: Select a clean location free of excess vibration where
the temperature of the unit will be between 0°F (-18°C) and 160°F
(71°C). Distance from the receiver is limited only by total loop
resistance. See “Electrical Connections”. The tubing supplying
pressure to the transmitter can be run practically any distance.
Long tubing lengths will not affect accuracy but response time will
be increased slightly.
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
SPECIFICATIONS
Service: Clean/dry air and compatible gases.
Wetted Materials: Consult factory.
Accuracy: ±0.5% or ±0.25% full scale.
Stability: ±0.5% F.S./year.
Pressure Limits: 100 psig (6.89 bar); 15 psid (1.03 bar).
Temperature Limits: -20 to 185°F (-28 to 85°C).
Compensated Temperature Range: 0 to 160°F (-18 to 71°C).
Thermal Effect: 0.5% Accuracy: ±0.02% F.S./°F;
0.25% Accuracy: ±0.01% F.S./°F.
Power Requirements: 12 to 36 VDC (2-wire).
Output Signal: 4-20 mA DC.
Zero and Span Adustments: Potentiometers for zero and
span.
Response Time: 250 ms.
Loop Resistance: DC: 0-1045 ohms maximum.
Current Consumption: 4-20 mA.
Electrical Connections: Screw terminal: Two 1/2˝ female NPT
conduit.
Process Connections: Two 1/4˝ female NPT.
Enclosure Rating: NEMA 4X (IP65).
Mounting Orientation: Not position sensitive.
Weight: 2 lb (0.9 kg).
Agency Approvals: FM approved intrinsically safe for use in
Class I, Div. 1, Groups A, B, C, D; Class II, Div. 1, Groups E, F, G;
Class III, Div. 1 when wired with approved intrinsically safe barrier.
Entity parameters: Vmax= 36 VDC; Imax= 250 mA; CI=12 nF; LI=0
mH.
Phone: 219/879-8000
Fax: 219/872-9057
www.dwyer-inst.com
e-mail: [email protected]
E-60
8/18/05
8:55 AM
Page 2
Bulletin E-60
Load Limitations 4-20 mA Output Only
2. Position: The Series 608 Transmitter is not position sensitive.
However, it is recommended that you avoid mounting with pressure connections pointing up because of the chance of condensed moisture entering the interior. Moisture can also be avoided by routing tubing with a low point just ahead of the transmitter.
LOOP RESISTANCE (1)
1250
1045
1000
3. Mounting: Attach to mounting surface with two #8 or #10
screws in the mounting slots provided.
4. Pressure Connections: The 608 series transmitter is shipped
with the “HIGH” and “LOW” pressure ports plugged to avoid
debris entering the unit. The plugs should be left in place until the
tubing and fittings are connected. For gage pressures, connect
positive (above atmospheric) pressure to the port marked “HIGH”
and vent the “LOW” port. To monitor vacuum, connect negative
(vacuum) pressure to port marked “LOW” and vent the “HIGH”
port. For differential pressure, connect the higher one to the
“HIGH” port and the lower one to the “LOW” port.
ELECTRICAL CONNECTION
Use in hazardous location: The Series 608 transmitter is FM
approved intrinsically safe for use in hazardous locations. See
specifications for details. Intrinsically safe approved devices require
the use of an approved intrinsic safety barrier when applied in hazardous locations. The barrier limits the amount of electrical or thermal energy in the instrument loop, to the level which would not
cause ignition in the hazardous location for which it is rated. The
barrier must be installed outside of the hazardous area and properly wired to the transmitter according to Figure B.
CAUTION: Do not exceed the specified supply voltage rating.
Permanent damage, not covered by warranty, may result. This unit
is not designed for AC voltage operation.
The terminal connections can be accessed by unscrewing the four
cover screws and removing the terminal block access cover. Bring
cable wires in through one of the 1/2˝ female NPT conduit connections, plugging the unused entry. Attach the cable wires to the
appropriate terminals. If polarity is inadvertently reversed, the loop
will not function properly but no damage will be done to the transmitter because of internal circuit protection. The power required to
generate the 4-20 mA output signal depends on the loop resistance of the circuit and is proportional to the resistance according
to the graph and formula in Figure C. The maximum length that
can be used in the current loop is a function of wire size and
receiver resistance. A shielded two conductor cable is recommended for control loop wiring. Make sure total loop resistance is
within the operating region as shown in Figure C.
HAZARDOUS AREA
SAFE AREA
ENTITY APPROVED
BARRIERS
SUPPLY
RETURN
750
545
500
OPERATING
REGION
250
0
10 12
0
20 24 30
36 40
LOOP SUPPLY VOLTAGE (VDC)
V min = 12V + (.022A x RL)
RL = RS + RW
RL = Loop Resistance (ohms)
RS = Sense Resistance (ohms)
RW = Wire Resistance (ohms)
Fig. C
CALIBRATION
Each Series 608 Transmitter is factory calibrated to the range listed in the model number chart. Range is defined as that pressure
which when applied to the transmitter will produce a 20 milliamp
current in the loop. Zero pressure will produce 4 milliamps. If fine
adjustment of calibration is required, use the following procedure:
1. With the transmitter connected to its companion receiver, insert
a milliammeter in series with the current loop. A controllable pressure source should be tied to the high pressure port of the transmitter and to an accurate pressure gage or manometer.
2. Apply electrical power to the system and allow 15 seconds for
components to stabilize.
3. With no pressure applied to the transmitter remove cover and
adjust “zero” control so loop current is at 4 mA.
4. Apply full span pressure and adjust loop current to 20 mA using
“span” control.
5. Remove the milliammeter from the circuit, replace cover, and
place system in service.
MAINTENANCE
After final installation of the Series 608 Differential Pressure
Transmitter, no routine maintenance is required. A periodic check
of system calibration is suggested. These devices are not field
repairable and should be returned if repair is needed (field repair
should not be attempted and may void warranty). Be sure to
include a brief description of the problem plus any relevant application notes. Contact customer service to receive a return goods
authorization number before shipping.
Fig. B
©Copyright 2005 Dwyer Instruments, Inc.
Printed in U.S.A. 8/05
DWYER INSTRUMENTS, INC.
P.O. BOX 373 • MICHIGAN CITY, INDIANA 46361, U.S.A.
Phone: 219/879-8000
Fax: 219/872-9057
FR# R1-443350-00
www.dwyer-inst.com
e-mail: [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement