MAF0165D

E
JOB NAME: ___________________________
ELECTRICALLY OPERATED
STEAM BOILER
ITEM NO.: ____________________________
NO. REQUIRED: _______________________
MODELS
‰‰ M24E - 24” wide, 24 kW electric boiler
‰‰ M36E - 36” wide, 24 kW electric boiler
DESCRIPTION
Electric Steam Boiler
FOOD SERVICE EQUIPMENT
The Market Forge CSD-1 compliant electrically operated steam boiler is mounted in a polished stainless steel cabinet base of modular
design to match other Market Forge cooking equipment. Equipped
with 6” (152mm) stainless steel legs, adjustable bullet feet, stainless steel counter top and single lift off front panel. No connection
or piping extends beyond either end of the cabinet, and all piping is
enclosed. Frame construction is 8 gauge stainless steel, type 409.
Unit is automatically filled with cold water and brought to pressure
when the power and heat switches are turned on and automatically
drained, under pressure, when the power switch is turned off. Cold
water drained under pressure shall automatically exhaust steam
before releasing it to the drain.
Boiler has automatic drain capability as standard. Access port for
Total Concept and PM Plus delimer, descaler and corrosion inhibitor
and a single ASSE approved, check valve/backflow preventer to the
boiler feed are included.
Note: Boiler is suitable for operation at any pressure from 5-15 PSI
(0.4 kg/cm2). If two operating pressures are required, such as 5 PSI
to one unit and 15 PSI to another specify pressure reducing valve to
provide 5 PSI (0.4 kg/cm2) operation.
The only available space to supply utilities to the boiler is the 6”
(152mm) space between the floor and the cabinet.
OPERATION SHALL BE BY:
Electrically powered, A.S.M.E. constructed and National Board
Registered, MAWP 15 PSI (1kg/cm2) boiler equipped for operation
with:
„„ M24E - 24 kW (36, 42, 48 kW option available)
„„ M36E - 24 kW (36, 42, 48 kW option available)
SHIPPING WEIGHT
„„ M24E - 330 lbs (150 kg)
„„ M36E - 530 lbs (240 kg)
M24E
M36E
STANDARD FEATURES:
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
„„
CSD-1 Compliant
Nickel Plated
ASSE Approved backflow preventer
Pressure Gauge
Cold Water Condenser
Water Strainer
Automatic Water Level Control
Air Vent
One Power Supply
Low Water Cut-off
Water Gauge Glass
Operating and High Limit Pressure Controls
Safety Relief Valve and Cathodic Descaler
Boiler is Insulated as Standard
Totally Serviceable from the Front
OPTIONS & ACCESSORIES
(at additional charge)
‰‰
‰‰
‰‰
‰‰
‰‰
‰‰
‰‰
‰‰
Quick disconnect water lines (2) required
Casters
KleenSteam Filter System
Flanged Feet
Twin Check Valve
Steam Take-Off Kit
Pressure Reducing Valve
Prison package, includes lockable stainless steel hinged
control cover, tamper proof screws, (2) 4” adjustable front
flanged feet
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
E. Friedman Associates Inc.
E
ELECTRICALLY OPERATED
STEAM BOILER
ELECTRICAL REQUIRMENTS
Volts
Phase 24kW 36kW 42kW 48kW
208 (197-219)
3
66
100
117
-
240 (220-240)
3
60
91
-
116
480 (360-500)
3
32
47
-
58
Details of other electrical systems available upon request.
SERVICE CONNECTIONS
EP
Power Supply - Use wire suitable for at least 90°C.
Nominal amp per line wire:
Electric Steam Boiler
FOOD SERVICE EQUIPMENT
CW1 Cold Water - 3/8” (10mm) NPT for cold water to boiler.
Cold water lines will have a maximum of 50 PSI (3.5kg/
cw2) and a minimum of 25 PSI (1.8 kg/cw2) water pressure (Water may be filtered).
CW2 Cold Water - 3/8” (10mm) NPT for cold water to condenser. Cold water lines will have a maximum of 50
PSI (3.5kg/cw2) and a minimum of 25 PSI (1.8 kg/cw2)
water pressure.
D
ST
Drain - Pipe full 2” (50mm) NPT to flush floor drain
capable of receiving water flowing at a maximum rate of
5 gallons (19 liters) per minute. DO NOT MAKE SOLID
CONNECTION TO FLOOR DRAIN.
Steam Take-off - Connection for operation of adjacent
steam powered equipment.
The only available space to supply utilities to the electric boiler is
the 6” (152mm) space between the floor and the cabinet.
DETAILS & DIMENSIONS
DRAIN LINE INSTALLATION: The drain port of the unit is marked
with a colored tag and is located at the lower rear left side of the
boiler as viewed from the front. This exhaust line may be left open
if the boiler has to be situated in a tiled floor depression or a tiled
curb section that is equipped with drain facilities. If this is not the
case, then a 2” (51mm) NPT drain line must be connected to
divert the exhaust to the floor drain. If it is necessary to use more
than three elbows, increase the size of the waste line accordingly.
WARNING: DO NOT UNDER ANY CIRCUMSTANCE CONNECT
THE EXHAUST DRAIN LINE DIRECTLY TO A SEWER LINE.
DIMENSIONS ARE IN INCHES [MM]
2.5 [64]
D
12 [305]
10.5
[267]
CW1
1.75 [43]
33
[838]
15.75
[400]
9.5 [241]
CW2
3 [76]
PVC & CPVC PIPE ARE NOT ACCEPTABLE MATERIALS FOR
DRAINS.
CAUTION: Before connecting water to this unit, water supply
should be analyzed to make sure hardness is no greater than
2.0 grains and pH level is within the range of 7.0-8.5. Water
which fails to meet these standards should be treated by installation of water conditioner. EQUIPMENT FAILURE CAUSED BY
INADEQUATE WATER QUALITY IS NOT COVERED UNDER
WARRANTY.
24 [610] M24E
36 [914] M36E
4 [102]
19 [483]
EP
ST
ST
28
[711]
22
[559]
CW1
D
EP
6 [152]
CW2
The manufacturer reserves the right to modify materials and specifications without notice.
PRINTED IN U. S. A.
SPEC SHEET: 14-0112 Rev B (12/14)
44 Lakeside Avenue, Burlington, VT 05401 USA • Tel: (802) 658-6600 • Fax: (802) 864-0183
www.mfii.com
E. Friedman Associates Inc.
Download PDF