57-2

2H Hydraulic Cylinders
Heavy Duty NFPA Tie Rod Cylinders for
Working Pressures up to 210 bar
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Mounting Styles
2H Cylinder Mounting Styles
The standard range of Parker 2H cylinders comprises 17
mounting styles. Dimensional information for each mounting
style is shown on pages 10-21 for 38.1mm to 203.2mm (11/2” to
8”) bore sizes, and on pages 22-25 for 254mm and 304.8mm
(10” and 12”) bore sizes.
NFPA MX3
TB
NFPA MF5
JB
NFPA MF6
HB
NFPA MS4
F
NFPA MS7
G
NFPA MP1
NFPA ME6
HH
NFPA MS2
BB
NFPA ME5
JJ
NFPA MF2
C
NFPA MX1
TD
NFPA MF1
H
NFPA MX2
TC
J
Application-specific mounting information is shown on page 30.
Where a non-standard mounting style is required, please
contact the factory for details.
ISO 6982 and
CETOP RP88H
SBa
NFPA MT1
D
NFPA MT2
NFPA MT4
K
(KTB shown)
DB
Most mounting styles
are available as double
rod cylinders
DD
2
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Piston Rod End Data
38.1mm to 203.2mm (11/2” to 8”) Bores Only
Rod End Styles 4, 7 & 8
– All Except JJ Mount
A
W
Rod End Styles 4 & 8
The standard rod end, Style 4, is recommended for all
applications in which the work piece is secured against the rod
shoulder. Where the work piece is not shouldered, Style 8 rod
ends are recommended.
Rod End Style 9
– All Except JJ Mount
W
V
V
Rod End Style 9
For applications where a female thread is required.
B NA
KK
B NA
MM
D
Wrench Flats
KK
MM
Rod End Style 3
Non-standard piston rod ends are designated ‘Style 3’.
A dimensional sketch or description should accompany the
order. Please specify dimensions KK and A.
D
Wrench Flats
A
Rod End Styles 4, 7 & 8
– JJ Mount Only
A1
Rod End Style 7
Rod End Style 9
– JJ Mount Only
Style 7 rod ends apply to rod eyes with spherical bearings
only (see pages 27 and 29). The Style 7 rod end with spherical
bearing allows the same diameter pivot pin to be used at both
the head and cap ends of the cylinder. For Style 7 rod end
thread lengths, please refer to dimension A1 in the table below.
WF
WF
RT
RD
RD
Style JJ
Dimensions which are not shown are identical to those shown
for the equivalent non-JJ design.
A1
RT
Rod End Dimensions – 38.1mm to 203.2mm (11/2” to 8”) bore sizes only
Style 4 & 9
Bore Rod
Ø
No.
MM
Rod
Diameter
KK
Metric
38.1
(11/2")
1
2
15.9 (5/8")
25.4 (1")
M10x1.5
M20x1.5
50.8
(2")
1
2
25.4 (1")
34.9 (13/8")
63.5
(21/2")
1
2
3
82.6
(31/4")
Style 8
Style 7 2
+0.00
JJ Mount Only
A
B -0.05
D
NA
V
W
RD
max.
RT
WF
21
19.0
28.6
28.55
38.07
13
22
14.3
23.8
6.4
12.7
15.9
25.4
54.0
63.5
9.5
9.5
25.4
35.0
27
28.6
41.3
38.07
50.77
22
30
23.8
33.3
6.4
9.5
19.1
25.4
63.5
76.2
9.5
9.5
35.0
41.3
–
M27x2
M27x2
35
28.6
50.8
41.3
38.07
60.30
50.77
22
36
30
23.8
42.9
33.3
6.4
12.7
9.5
19.1
31.8
25.4
63.5
88.9
76.2
9.5
9.5
9.5
35.0
47.7
41.3
11/4 - 12
13/4 - 12
11/2 - 12
–
M33x2
M33x2
44
41.3
57.1
50.8
50.77
66.65
60.30
30
41
36
33.3
49.2
42.9
6.4
9.5
9.5
22.2
31.8
28.6
76.2
101.6
88.9
9.5
15.9
9.5
41.3
50.8
47.7
M39x2
M56x2
M45x2
11/2 - 12
21/4 - 12
13/4 - 12
–
M42x2
M42x2
55
50.8
76.2
57.1
60.30
79.35
66.65
36
55
41
42.9
60.3
49.2
6.4
9.5
6.4
25.4
34.9
28.6
88.9
114.3
101.6
9.5
15.9
15.9
47.7
57.2
50.8
11/2 - 12
21/2 - 12
17/8 - 12
21/4 - 12
M45x2
M76x2
M56x2
M68x2
13/4 - 12
31/4 - 12
21/4 - 12
23/4 - 12
–
M48x2
M48x2
–
62
57.1
88.9
76.2
88.9
66.65
107.92
79.35
95.22
41
75
55
65
49.2
85.7
60.3
73.0
6.4
9.5
9.5
9.5
28.6
34.9
34.9
34.9
101.6
146.1
114.3
133.4
15.9
15.9
15.9
15.9
50.8
57.2
57.2
57.2
M48x2
M76x2
M58x2
M64x2
17/8 - 12
3 - 12
21/4 - 12
21/2 - 12
M56x2
M95x2
M68x2
M76x2
21/4 - 12
33/4 - 12
23/4 - 12
31/4 - 12
–
M64x2
–
M64x2
84
76.2
101.6
88.9
88.9
79.35
120.62
95.22
107.92
55
85
65
75
60.3
98.4
73.0
85.7
6.4
6.4
6.4
6.4
31.8
31.8
31.8
31.8
114.3
165.1
133.4
146.1
15.9
19.1
15.9
15.9
57.2
57.2
57.2
57.2
76.2 (3")
127.0 (5")
88.9 (31/2")
101.6 (4")
M58x2
M90x2
M64x2
M76x2
21/4 - 12
31/2 - 12
21/2 - 12
3 - 12
M68x2
M110x2
M76x2
M95x2
23/4 - 12
43/4 - 12
31/4 - 12
33/4 - 12
–
–
–
–
–
88.9
127.0
88.9
101.6
95.22
146.02
107.92
120.62
65
110
75
85
73.0
123.8
85.7
98.4
6.4
6.4
6.4
6.4
31.8
31.8
31.8
31.8
133.4
190.5
146.1
165.1
15.9
25.4
15.9
19.1
57.2
57.2
57.2
57.2
88.9 (31/2")
139.7 (51/2")
101.6 (4")
127.0 (5")
M64.2
M100x2
M76x2
M90x2
21/2 - 12
4 - 12
3 - 12
31/2 - 12
M76x2
M130x2
M95x2
M110x2
31/4 - 12
51/4 - 12
33/4 - 12
43/4 - 12
–
–
–
–
–
88.9
139.7
101.6
127.0
107.92
158.72
120.62
146.02
75
120
85
110
85.7
136.5
98.4
123.8
6.4
6.4
6.4
6.4
31.8
31.8
31.8
31.8
146.1
209.6
165.1
190.5
15.9
19.1
19.1
25.4
57.2
57.2
57.2
57.2
KK
UNF 1
KK
Metric
7
/16 - 20
3
/4 - 16
M12x1.5
M22x1.5
1
M20x1.5
M26x1.5
3
/4 - 16
1 - 14
M22x1.5
M30x2
7
25.4 (1")
44.5 (13/4")
34.9 (13/8")
M20x1.5
M33x2
M26x1.5
3
/4 - 16
11/4 - 12
1 - 14
M22x1.5
M39x2
M30x2
7
/8- 14
11/2- 12
11/4- 12
1
2
3
34.9 (13/8")
50.8 (2")
44.5 (13/4")
M26x1.5
M39x2
M33x2
1 - 14
11/2 - 12
11/4 - 12
M30x2
M45x2
M39x2
101.6
(4")
1
2
3
44.5 (13/4")
63.5 (21/2")
50.8 (2")
M33x2
M48x2
M39x2
11/4 - 12
17/8 - 12
11/2 - 12
127.0
(5")
1
2
3
4
50.8 (2")
88.9 (31/2")
63.5 (21/2")
76.2 (3")
M39x2
M64x2
M48x2
M58x2
152.4
(6")
1
2
3
4
63.5 (21/2")
101.6 (4")
76.2 (3")
88.9 (31/2")
177.8
(7")
1
2
3
4
203.2
(8")
1
2
3
5
KK
UNF
KK
Metric
/2 - 20
7
/8- 14
–
M16x1.5
M20x1.5
/8- 14
11/4 - 12 M20x1.5
A1
1
All dimensions are in millimetres unless otherwise stated.
2
3
All rod threads are UNF except 1” - 14 which is UNS.
Style 7 threads apply to spherical rod eyes only, see pages 27 and 29.
Parker Hannifin
Cylinder Division
Europe
Storage and Installation, Cylinder Masses
Tie Rod Cylinders
2H Series
Storage
Masses – Series 2H Cylinders
Catalogue HY07-1110/UK
When cylinders must be stored for a period of time, the
following procedures are recommended:
1. Store the cylinders in an indoor area which has a dry, clean and non-corrosive atmosphere. Take care to protect the cylinder from both internal corrosion and external damage.
To determine the mass of the cylinder, first select the basic
mass for zero stroke, then calculate and add the mass for the
appropriate stroke length. Masses for accessories are shown on
pages 27 to 29.
2. Whenever possible, cylinders should be stored in a vertical position (piston rod up). This will minimize corrosion due to possible condensation which could occur inside the cylinder.
3. Port protector plugs should be left in the cylinder until the time of installation.
Single Rod Cylinders
Mass at Zero Stroke
Bore
Ø
Rod
No.
Double Rod Cylinders
Mass at Zero Stroke
Mass
Mass
Mounting Styles
per
per
TB, TC, JJ, HH, D, 10mm
TB, TD, JJ, C, G, 10mm
TD, J, JB, DB, DD, C, Stroke
J, JB, F
D, DD Stroke
H, HB, F G, SBa, BB
kg
kg
Mounting Styles
kg
kg
kg
kg
38.1
(11/2")
1
2
3.6
3.7
4.7
4.9
0.09
0.11
4.1
4.4
5.23
5.53
0.10
0.15
1. Cleanliness is an important consideration, and Parker
cylinders are shipped with the ports plugged to protect them
from contaminants entering the ports. These plugs should
not be removed until the piping is to be installed. Before
making the connection to the cylinder ports, piping should
be thoroughly cleaned to remove all debris which might have
resulted from threading or flaring operations.
50.8
(2")
2. Cylinders operating in an environment where air drying
materials are present such as fast-drying chemicals, paint,
or weld splatter, or other hazardous conditions such as
excessive heat, should have shields installed to prevent
damage to the piston rod and piston rod seals.
101.6
(4")
1
2
1
2
3
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
5
1
2
1
2
5.7
6.0
7.9
8.7
8.2
15.2
16.1
15.7
20.4
22.2
20.8
36
41
37
39
58
64
60
62
86
97
88
90
120
135
123
130
275
291
444
474
7.5
7.8
10.1
11.0
10.8
19.4
20.4
19.9
25.7
27.5
26
44
49
46
47
71
77
73
75
105
116
107
109
145
160
148
155
328
344
527
557
0.14
0.18
0.19
0.27
0.22
0.31
0.39
0.36
0.39
0.51
0.42
0.59
0.92
0.68
0.79
0.92
1.3
1.1
1.2
1.2
1.8
1.3
1.4
1.6
2.3
1.8
2.1
3.0
4.0
3.9
5.6
6.9
7.5
9.4
11.0
10.0
18.2
20.0
19.2
25
29
26
43
53
46
49
68
80
71
74
99
122
103
108
137
166
142
157
325
357
519
579
8.74
9.34
11.7
13.3
12.7
22.5
24.3
23.5
31
35
32
52
62
55
58
82
94
85
88
119
142
123
128
163
192
168
183
378
410
603
663
0.18
0.25
0.23
0.39
0.30
0.39
0.55
0.48
0.51
0.76
0.58
0.75
1.40
0.93
1.20
1.2
2.0
1.4
1.7
1.5
2.8
1.8
2.1
2.1
3.5
2.4
3.1
4.0
5.9
5.1
8.4
Installation
63.5
(21/2")
82.6
(31/4")
127.0
(5")
3. Correct alignment of the cylinder piston rod and its mating
component on the machine should be checked in both the
extended and retracted positions. Incorrect alignment will
result in excessive rod gland and/or cylinder bore wear,
shortening the life of the cylinder.
152.4
(6")
177.8
(7")
203.2
(8")
254.0
(10")
304.8
(12")
Warning
FAILURE OR IMPROPER SELECTION OR IMPROPER USE OF THE PRODUCTS AND/OR SYSTEMS DESCRIBED HEREIN OR RELATED
ITEMS CAN CAUSE DEATH, PERSONAL INJURY AND PROPERTY DAMAGE.
This document and other information from Parker Hannifin Corporation, its subsidiaries, sales offices and authorized distributors provide
product or system options for further investigation by users having technical expertise. Before you select or use any product or system it is
important that you analyse all aspects of your application and review the information concerning the product or system in the current product
catalogue. Due to the variety of operating conditions and applications for these products or systems, the user, through his own analysis
and testing, is solely responsible for making the final selection of the products and systems and assuring that all performance and safety
requirements of the application are met.
The products described herein, including without limitation, product features, specifications, designs, availability and pricing, are subject to
change by Parker Hannifin Corporation and its subsidiaries at any time without notice.
Offer of Sale
Please contact your local Parker representative for a detailed offer of sale.
All dimensions are in millimetres unless otherwise stated.
4
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Introduction
Parker Offers the Widest Range of Industrial Cylinders
ContentsPage
High Productivity – Low Cost of Ownership
Parker Hannifin's Cylinder Division is the world's largest supplier
of hydraulic cylinders for industrial applications.
Parker manufactures a vast range of standard and special
tie rod, roundline and 'mill' type cylinders to suit all types of
industrial cylinder applications. Our cylinders are available to ISO,
DIN, NFPA, ANSI and JIC standards, with other certifications
available on request. All Parker hydraulic cylinders are
designed to deliver long, efficient service with low maintenance
requirements, guaranteeing high productivity year after year.
About Parker Hannifin
Parker Hannifin is the global leader in motion and control
technologies, partnering with its customers to increase their
productivity and profitability. The company employs more than
52,000 people in 48 countries around the world, providing
customers with technical excellence and first class customer
service.
Visit us at www.parker.com
Mounting Styles
2, 9
Piston Rod End Data –
38.1mm to 203.2mm (11/2" to 8") bores
3
Storage Information and Mass Data
4
Standard Specifications
5
Design Features and Benefits
6
Optional Features
8
Mounting Dimensions –
38.1mm to 203.2mm (11/2" to 8") bores
10
254.0mm to 304.8mm (10" and 12") bores
22
Double Rod Cylinders
26
Accessories27
Mounting Information
30
Push and Pull Forces
31
Pressure Limitations
32
Piston Rod Sizes and Stroke Factors
33
Stop Tubes & Long Stroke Cylinders
34
Ports, Locations and Piston Speeds
35
Cushioning36
37
Seals and Fluids
38
Replacement Parts and Service
Repairs39
Piston Rod End Data – 254.0mm and 304.8mm (10" and 12") bores 40
41
How to Order Cylinders
The 2H Cylinder Range
The 2H cylinders described in this catalogue are heavy duty
hydraulic cylinders rated for use at working pressures up to 210
bar depending on the rod end and type of service.
In addition to the standard cylinders featured in this catalogue,
2H cylinders can be designed to suit customer requirements.
Our engineers will be pleased to advise on unique designs to
suit specific applications.
inPHorm and 3-D CAD
Parker offers easy-to-use software to simplify the cylinder
selection process, saving your time and ensuring the accuracy
of designs and drawings. InPHorm selection software and new
3-D CAD modelling software can be downloaded from our
Cylinder Division Europe website.
Please visit us at www.parker.com or contact your local Sales
Office for more information.
Standard Specifications
• Bore sizes – 38.1mm (11/2”) to 304.8mm (12”)
• Heavy-duty service – ANSI B93.15-1987 and NFPA specifications
• Piston rod diameters – 15.9mm (5/8”) to 215.9mm (81/2”)
• Standard construction – square end, tie rod design
• Mounting styles – 17 standard styles
• Standard pressure – 210 bar
• Strokes – available in any practical stroke length
• Standard fluid – hydraulic mineral oil
• Cushions – optional at either end or both ends of stroke
• Standard temperature – -20°C to 80°C (-4°F to 176°F)
• Rod ends – three standard choices, specials to order
5
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Design Features and Benefits
3
2
5
11
12
10
6
8
1
4
1 Piston Rod
Gland seal life is maximised by manufacturing piston rods from
precision ground, high tensile carbon alloy steel, hard chrome
plated and polished to 0.2µm max. Piston rods are induction
case hardened to Rockwell C54 minimum before chrome
plating, resulting in a dent-resistant surface.
2 Parker’s Rod Gland
Continuous lubrication, and therefore longer gland life, are
provided by the long bearing surface inboard of the lipseal. The
gland, complete with rod seals, can easily be removed without
dismantling the cylinder, so servicing is quicker – and therefore
more economical.
3 Rod Seals
The serrated lipseal has a series of sealing edges which take
over successively as pressure increases, providing efficient
sealing under all operating conditions. On the return stroke the
serrations act as a check valve, allowing the oil adhering to the
rod to pass back into the cylinder.
9 & 10
7
9
11
fluid and a life of up to five times that of traditional seal materials.
Standard rod seals are suitable for speeds up to 0.5m/s – special
seal combinations are available for higher speed applications.
4 Cylinder Body
Strict quality control standards and precision manufacture
ensure that all tubes meet rigid standards of straightness,
roundness and surface finish. The steel tubing is surface
finished to minimise internal friction and prolong seal life.
5 Cylinder Body Seals
To ensure that the cylinder body remains leak free, even under
pressure shock conditions, Parker fits pressure-energised
body seals.
6Piston
All pistons are of one-piece type, and feature wide bearing
surfaces to resist side loading. Long thread engagement secures
the piston to the piston rod and, for additional safety, the piston
is secured by thread-locking adhesive and a locking pin.
7 Piston Seals
Cast Iron Piston Rings are extremely durable but allow some
leakage across the piston and cannot therefore hold a load in
position. Cast iron piston rings are fitted as standard on series
2H hydraulic cylinders.
Lipseal Pistons can hold a load in position, but are not as
durable as pistons with cast iron rings or Hi-Load seals. For
applications with a working pressure in excess of 140 bar where
the duty cycle requires sustained piston speeds in excess of
0.4m/s or high cycling performance, other seal options should
also be considered. Where these performance criteria may
be exceeded, please contact the factory with details of the
application.
The double lip wiperseal acts as a secondary seal, trapping
excess lubricating film in the chamber between the wiper and lip
seals and preventing the ingress of dirt into the cylinder, extending
the life of gland and seals. Standard lipseals are manufactured
from an enhanced polyurethane, giving efficient retention of
6
Hi-Load Pistons resist side loading and are recommended for
long stroke cylinders, especially when pivot mounted. Special
wear rings prevent metal-to-metal contact between the piston
and tube and thereby extend the life of the cylinder.
Low Friction Seals are also available – see page 37.
Parker Hannifin
Cylinder Division
Europe
Features and Benefits
Tie Rod Cylinders
2H Series
8Ports
Seal Classes
9Cushioning
Special Designs
Catalogue HY07-1110/UK
High piston speeds allow rapid cycling, which maximises
machine productivity. Parker offers a range of port sizes to
permit different flow rates, in all common inch and metric
standards. Choosing the correct port size simplifies design and
installation, and cuts maintenance time to a minimum.
Progressive deceleration reduces both noise and shock,
prolonging machine life and improving the working environment.
Parker 2H cylinders are available with stepped cushions at the
head and cap, which decelerate a load safely while optimising
the cycling rate of the process. The head and cap end cushions
are self-centring. The polished cap end spear is an integral part
of the piston rod.
To accommodate the many types of fluid and the varying
temperature ranges used in industry, Parker offers a range of
rod gland, piston and body seals moulded in different profiles
and from different materials. These are described in detail on
page 37.
Parker’s design and engineering staff are available to produce
special designs to meet customer’s specific requirements.
Alternative sealing arrangements, special mounting styles,
different bores and rod sizes are just a few of the custom
features which can be supplied.
10Floating Cushion Bushes & Sleeves
Closer tolerances – and therefore more effective cushioning
– are permitted by the use of a floating cushion sleeve at the
head end of the cylinder, and a floating cushion bush at the cap
end. A specially designed cushion sleeve on bore sizes up to
101.6mm (4”) operates as a check valve. On larger bore sizes a
conventional ball check valve is used. The use of a check valve
in the head and lifting of the bronze cushion bush in the cap,
provides minimum fluid flow restriction at the start of the return
stroke. This allows full pressure to be applied over the whole
area of the piston, to provide full power and fast cycle times.
11Cushion Adjustment
Needle valves are provided at
both ends of the cylinder for
precise cushion adjustment,
and retained within the head
and cap so that they cannot
be inadvertently removed. The cartridge type needle
valve illustrated is fitted to
cylinders of up to 63.5mm
(21/2”) bore. See page 35 for
location.
12 Tie Rod Construction
Tie rod construction, with tie rods torque-loaded on assembly,
imposes a compressive force on the cylinder tube which
counters the tensile forces generated by system pressure.
The result – a fatigue-free cylinder with long service life and
exceptionally compact dimensions.
7
Parker Hannifin
Cylinder Division
Europe
Optional Features
Tie Rod Cylinders
2H Series
Air Bleeds
Rod Locking Devices
Catalogue HY07-1110/UK
The option of air bleeds is available
at either or both ends of the
cylinder, at any position except
in the port face – see page 35 for
location. To ensure operator safety,
the standard M8 air bleed screw
(illustrated) is recessed into the
head and cap and retained so that it
cannot be inadvertently removed.
These units provide positive locking of the piston rod. They
require hydraulic pressure to release, while loss of pressure
causes the clamp to operate, allowing them to be used as a failsafe device. Please consult the factory for further information.
Single-Acting Cylinders
Standard 2H series cylinders are of the double-acting type.
They are also suitable for use as single-acting cylinders, where
the load or other external force is used to return the piston after
the pressure stroke. Cast iron piston rings should not be used
with single-acting cylinders.
Gland Drains
The accumulation of fluid between the gland seals of long
stroke cylinders, cylinders with constant back pressure or where
the ratio of the extend speed to the retract speed is greater
than 2 to 1, can be relieved by specifying an optional gland
drain. A transparent tube fitted between the gland drain and
the reservoir allows fluid loss from concealed or inaccessible
cylinders to be monitored, giving an early indication of the need
for gland servicing.
Spring-Returned, Single-Acting Cylinders
Single-acting cylinders can be supplied with an internal spring
to return the piston after the pressure stroke. Please supply
details of load conditions and friction factors, and advise whether
the spring is required to advance or return the piston rod.
On spring-returned cylinders, it is recommended that tie rod
extensions be specified to allow the spring to be ‘backed off’
until compression is relieved. Please consult the factory when
ordering spring-returned cylinders.
Multiple Stroke Positioning
A 1/8” NPTF gland drain port can be provided in the retainer on
all cylinders up to and including 203.2mm (8”) bore sizes, except
38.1mm (11/2”) with no. 1 rod. For 38.1mm (11/2”) bore cylinders
with no.2 rod, the retainer thickness is increased to 15.9mm
(5/8”). For 38.1mm (11/2”) bore cylinders with no.1 rod, the drain
port is located in the head end adjacent to the port.
Stroke Limiters
Where absolute precision in stroke length is required, a screwed
adjustable stop can be supplied at the cap end. Several types
are available – the illustration
Seal
shows a design suitable for
J
infrequent adjustment of
Wrench
Square
an uncushioned cylinder.
Please contact the factory,
specifying details of
the application and the
adjustment required.
L
K
Bore
Ø
J
K
min.
L
max.
38.1 (1 /2")
11
55
127.0
50.8 (2")
17
75
203.2
63.5 (21/2")
17
75
228.6
82.6 (31/4")
22
85
228.6
101.6 (4")
24
70
457.2
127.0 (5")
32
70
508.0
152.4 (6")
41
75
508.0
1
177.8 (7")
50
75
508.0
203.2 (8")
60
80
508.0
To obtain linear force in one plane with controlled stopping
at intermediate points, several designs are available. For
three stopped positions, it is common practice to mount two
standard single rod Style H cylinders back-to-back, or to use
through-tie rods. By extending or retracting the stroke of each
cylinder independently, it is possible to achieve three positions
at the piston ends. An alternative technique is to use a tandem
cylinder with an independent piston rod in the cap section.
Please consult the factory for further details.
Rod End Bellows
Unprotected piston rod surfaces which are exposed to
contaminants with air hardening properties should be protected
by rod end bellows. Longer rod extensions are required to
accommodate the collapsed length of the bellows. Please
consult the factory for further information.
Metallic Rod Wipers
Metallic rod wipers replace the standard wiper seal, and are
recommended where dust, ice or splashings might damage the
wiper seal material. They do not affect cylinder dimensions.
DC Proximity Sensors
These can be fitted to give precise, repeatable end of stroke
signals. Please contact the factory for details.
Position Feedback
Linear position transducers of various types are available for 2H
series cylinders. Please contact the factory for details.
All dimensions are in millimetres unless otherwise stated.
8
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Mounting Styles
Mounting Styles and Where to Use Them
See also application-specific mounting information on page 30.
Extended Tie Rod Mountings – Styles TB, TC and TD
Application
• straight line force transfer
• compression (push) – use cap end mountings TC or TD
• tension (pull) – use head end mountings TB or TD
Benefits
• ease of mounting where space is limited
• high efficiency – force is absorbed on cylinder's centreline
• TD double-ended mounting allows brackets or switches to be Styles TB, TC, TD
attached to cylinder
See pages 10-11
TB
Flange Mountings – Styles J, JB, JJ, H, HB and HH
Application • straight line force transfer
• compression (push) – use cap end mounting H, HB or HH
• tension (pull) – use head end mounting J, JB or JJ
Benefits
• exceptionally rigid mounting due to large flange area
• high efficiency – force is absorbed on cylinder's centreline
Styles J, JB, JJ, H, HB, HH
See pages 12-15, 22-23
HH
Foot Mountings – Style C, F, G
Application
• straight line force transfer
• suitable for push or pull applications
• force is not absorbed on centreline – secure attachment, eg: a thrust key (page 30) and effective load guidance are vital
Benefits
• ease of mounting and adjustment
Pivot Mountings – Styles BB and SBa
Application • curved path force transfer
• movement in a single plane – use fixed clevis style BB
• movement in more than one plane – use spherical bearing style SBd
Benefits
• ease of attachment – use with plain or spherical bearing at rod end
• greater flexibility for the machine designer
• self-alignment resists wear of cylinder's bearing surfaces
Styles C, F, G
See pages 16-17 and 25
C
Styles BB, SBa
See pages 18-19 and 25
BB
Styles D, DB, DD
See pages 20-21 and 24
DB
Trunnion Mountings – Styles D, DB and DD
Application • curved path force transfer
• movement in a single plane
• compression (push) – use DB or DD mountings
• tension (pull) – use D or DD mountings
Benefits
• greater flexibility for the machine designer
• self-alignment resists wear of cylinder's bearing surfaces
• high efficiency – force is absorbed on cylinder's centreline
• ease of attachment – use with pivot mounting at rod end
9
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Tie Rod Mountings 38.1 - 203.2mm bores
ZB + stroke
ZJ + stroke
P + stroke
Y
EE
E
1
AA
2 R
E 4
DD
Style TB
Tie Rods Extended Head End
(NFPA Style MX3)
BB
3
R
K
J
G
F
LB + stroke
See Notes 1, 2
ZB + stroke
ZJ + stroke
Y
P + stroke
EE
E
1
AA
E 4
2 R
DD
Style TC
Tie Rods Extended Cap End
(NFPA Style MX2)
F
J
G
3
R
BB
LB + stroke
K
See Notes 1, 2
Dimensions TB, TC & TD See also rod end dimensions, page 3 & mounting information, page 30
Bore
Ø
Rod
No.
AA
BB
38.1
(11/2")
1
2
58.4
34.9
3
50.8
(2")
1
2
73.7
46.0
1
63.5
(21/2")
1
2
3
91.4
46.0
1
82.6
(31/4")
1
2
3
116.8
58.7
5
101.6
(4")
1
2
3
137.2
58.7
5
127.0
(5")
1
2
3
4
177.8
81.0
7
152.4
(6")
1
2
3
4
205.7
177.8
(7")
1
2
3
4
203.2
(8")
1
2
3
5
DD 1
E
/8 - 24
63.5
/2 - 20
EE
F
G
J
G1/2
9.5
44.5
38.1
76.2
G1/2
15.9
44.5
38.1
/2 - 20
88.9
G1/2
15.9
44.5
38.1
/8 - 18
114.3
G3/4
19.1
50.8
44.5
/8 - 18
127.0
G3/4
22.2
50.8
44.5
/8 - 14
165.1
G3/4
22.2
50.8
44.5
92.1
1 - 14
190.5
G1
25.4
57.2
57.2
236.2
104.8
11/8 - 12
215.9
G11/4
25.4
69.9
69.9
269.2
114.3
11/4 - 12
241.3
G11/2
25.4
76.2
76.2
(BSPP)
All dimensions are in millimetres unless otherwise stated.
10
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Tie Rod Mountings 38.1 - 203.2mm bores
ZB + stroke
ZJ + stroke
P + stroke
Y
EE
E
1
AA
E 4
DD
Style TD
Tie Rods Extended Both Ends
(NFPA Style MX1)
2
R
DD
F
J
G
3
R
BB
LB + stroke
BB
See Notes 1, 2
Notes
1 All tie rod threads (dimension DD) are UNF, with the exception of 1 - 14 which is UNS
2 Mounting nuts should be tightened to the torque values shown for tie rod nuts – see page 30
Dimensions TB, TC & TD Continued
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
50.8
(2")
K
R
Y
10
41.4
49
59
1
2
13
52.1
63.5
(21/2")
1
2
3
13
82.6
(31/4")
1
2
3
101.6
(4")
max
+ Stroke
P
ZB max
ZJ
127.0
75
152.4
161.9
142.9
152.4
59
65
133.4
75
163.5
169.9
152.4
158.8
64.8
59
71
65
136.5
78
166.7
179.4
173.3
156.6
168.3
161.9
16
82.6
68
79
76
158.8
90
195.3
204.8
201.6
181.0
190.5
187.3
1
2
3
16
97.0
76
86
79
168.3
97
208.0
217.5
211.1
193.7
203.2
196.9
127.0
(5")
1
2
3
4
19
125.7
79
86
86
86
181.0
110
230.2
236.5
236.5
236.5
209.6
215.9
215.9
215.9
152.4
(6")
1
2
3
4
23
145.5
86
212.7
130
266.7
244.5
177.8
(7")
1
2
3
4
26
167.1
92
241.3
146
298.5
273.0
203.2
(8")
1
2
3
5
28
190.5
94
266.7
168
325.4
298.4
LB
All dimensions are in millimetres unless otherwise stated.
11
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Head Flange Mountings 38.1 - 203.2mm bores
ZB + stroke
P + stroke
Y
UF
E
EE
1
E
2
4
R
FB
(4 holes)
3
Style J
Head Rectangular Flange
(NFPA Style MF1)
F
J
G
K
TF
LB + stroke
See Note 1
UF
E
ZB + stroke
P + stroke
Y
1
EE
UF E 4
Style JB
Head Square Flange
(NFPA Style MF5)
2
R TF
FB
(8 holes)
3
F
G
J
R
K
TF
LB + stroke
Dimensions J, JB & JJ See also rod end dimensions, page 3 & mounting information, page 30
Bore
Ø
Rod
No.
E
38.1
(11/2")
1
2
63.5
50.8
(2")
1
2
63.5
(21/2")
EE
F
FB
G
J
K
KB
R
G1/2
9.5
11.1
44.5
38.1
10
0.0
41.4
76.2
G1/2
15.9
14.3
44.5
38.1
13
0.0
6.4
52.1
1
2
3
88.9
G1/2
15.9
14.3
44.5
38.1
13
0.0
6.4
6.4
64.8
82.6
(31/4")
1
2
3
114.3
G3/4
19.1
17.5
50.8
44.5
16
6.4
3.2
6.4
82.6
101.6
(4")
1
2
3
127.0
G3/4
22.2
17.5
50.8
44.5
16
6.4
6.4
3.2
97.0
127.0
(5")
1
2
3
4
125.7
152.4
(6")
(BSPP)
165.1
3
G /4
22.2
23.8
50.8
44.5
19
3.2
6.4
6.4
6.4
1
2
3
4
190.5
G1
25.4
27.0
57.2
57.2
22
6.4
6.4
6.4
6.4
145.5
177.8
(7")
1
2
3
4
215.9
G11/4
25.4
30.2
69.9
69.9
24
6.4
0.0
6.4
6.4
167.1
203.2
(8")
1
2
3
5
241.3
G11/2
25.4
33.3
76.2
76.2
27
6.4
6.4
6.4
0.0
190.5
All dimensions are in millimetres unless otherwise stated.
12
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Head Flange Mountings 38.1 - 203.2mm bores
ZB + stroke
P + stroke
LG + stroke
EE
Y
KB
UF
E
1
E 4
RD
RT
Style JJ
Rectangular Head
(NFPA Style ME5)
2
3
TF
K
FB
(4 holes)
J
G
R
Notes
1 For maximum pressure ratings in push applications, see page 32
Dimensions J, JB & JJ Continued
RD
Bore
Ø
Rod
No.
max
38.1
(11/2")
1
2
54.0
63.5
9.5
9.5
50.8
(2")
1
2
63.5
76.2
63.5
(21/2")
1
2
3
82.6
(31/4")
RT
TF
UF
Y
87.3
9.5
9.5
63.5
88.9
76.2
1
2
3
101.6
(4")
+ Stroke
LB
LG
P
ZB max
108.0
49
59
127.0
117.5
75
152.4
161.9
104.8
130.2
59
65
133.4
117.5
75
163.5
169.9
9.5
9.5
9.5
117.5
142.9
59
71
65
136.5
120.7
78
166.7
179.4
173.3
76.2
101.6
88.9
9.5
15.9
9.5
149.2
181.0
68
79
76
158.8
139.7
90
195.3
204.8
201.6
1
2
3
88.9
114.3
101.6
9.5
15.9
15.9
161.9
193.7
76
86
79
168.3
146.1
97
208.0
217.5
211.1
127.0
(5")
1
2
3
4
101.6
146.1
114.3
133.4
15.9
15.9
15.9
15.9
208.0
247.7
79
86
86
86
181.0
158.8
110
230.2
236.5
236.5
236.5
152.4
(6")
1
2
3
4
114.3
165.1
133.4
146.1
15.9
19.1
15.9
15.9
239.7
285.8
86
212.7
187.3
130
266.7
177.8
(7")
1
2
3
4
133.4
190.5
146.1
165.1
15.9
25.4
15.9
19.1
269.9
320.7
92
241.3
215.9
146
298.5
203.2
(8")
1
2
3
5
146.1
209.6
165.1
190.5
15.9
19.1
19.1
25.4
300.0
355.6
94
266.7
241.3
168
325.4
All dimensions are in millimetres unless otherwise stated.
13
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Cap Flange Mountings 38.1 - 203.2mm bores
UF
E
1
K
E 2
4
R
3
FB
(4 holes)
Style H
Cap Rectangular Flange
(NFPA Style MF2)
ZF + stroke
P + stroke
EE
Y
F
TF
J
G
LB + stroke
XF + stroke
UF
1
F
See Note 1
ZF + stroke
E
Y
P + stroke
EE
K
UF E 2
4
R TF
F
Style HB
Cap Square Flange
(NFPA Style MF6)
3
R
FB
(8 holes)
J
G
F
LB + stroke
TF
XF + stroke
Dimensions H, HB & HH See also rod end dimensions, page 3 & mounting information, page 30
Bore
Ø
Rod
No.
E
38.1
(11/2")
1
2
63.5
50.8
(2")
1
2
63.5
(21/2")
EE
F
FB
G
J
K
R
G1/2
9.5
11.1
44.5
38.1
10
41.4
76.2
G1/2
15.9
14.3
44.5
38.1
13
52.1
1
2
3
88.9
G1/2
15.9
14.3
44.5
38.1
13
64.8
82.6
(31/4")
1
2
3
114.3
G3/4
19.1
17.5
50.8
44.5
16
82.6
101.6
(4")
1
2
3
127.0
G3/4
22.2
17.5
50.8
44.5
16
97.0
127.0
(5")
1
2
3
4
165.1
G3/4
22.2
23.8
50.8
44.5
19
125.7
152.4
(6")
1
2
3
4
190.5
G1
25.4
27.0
57.2
57.2
22
145.5
177.8
(7")
1
2
3
4
215.9
G11/4
25.4
30.2
69.9
69.9
24
167.1
203.2
(8")
1
2
3
5
241.3
G11/2
25.4
33.3
76.2
76.2
27
190.5
(BSPP)
All dimensions are in millimetres unless otherwise stated.
14
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Cap Flange Mountings 38.1 - 203.2mm bores
UF
1
E
R 2
K
EE
4 E
3
TF
FB
(4 holes)
Style HH
Rectangular Cap
(NFPA Style ME6)
LB + stroke
P + stroke
Y
F
G
J
XF + stroke
Notes
1 For maximum pressure ratings in pull applications, see page 30
Dimensions H, HB & HH Continued
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
50.8
(2")
TF
UF
Y
87.3
108.0
49
59
1
2
104.8
130.2
63.5
(21/2")
1
2
3
117.5
82.6
(31/4")
1
2
3
101.6
(4")
1
2
3
127.0
(5")
1
2
3
4
152.4
(6")
+ Stroke
LB
P
XF
ZF
127.0
75
142.9
152.4
152.4
161.9
59
65
133.4
75
152.4
158.8
168.3
174.6
142.9
59
71
65
136.5
78
156.6
168.3
161.9
171.5
184.2
177.8
149.2
181.0
68
79
76
158.8
90
181.0
190.5
187.3
200.0
209.6
206.4
161.9
193.7
76
86
79
168.3
97
193.7
203.2
196.9
215.9
225.4
219.1
208.0
247.7
79
86
86
86
181.0
110
209.6
215.9
215.9
215.9
231.8
238.1
238.1
238.1
1
2
3
4
239.7
285.8
86
212.7
130
244.5
269.9
177.8
(7")
1
2
3
4
269.9
320.7
92
241.3
146
273.0
298.5
203.2
(8")
1
2
3
5
300.0
355.6
94
266.7
168
298.5
323.9
All dimensions are in millimetres unless otherwise stated.
15
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Foot Mountings 38.1 - 203.2mm bores
ZB + stroke
P + stroke
LB + stroke
EE
Y
See Notes 1, 3, 4
1
E
SB
(4 holes)
2
4
-0.15
E/2 -0.20
ST
F
Style C
Side Lug Mounting
(NFPA Style MS2)
G
K
J
SS + stroke
XS
3
E
SW
TS
SW
US
See Notes 1, 2
ZB + stroke
P + stroke
Y
LB + stroke
E
1
EE
E 4
2
-0.15
E/2 -0.20
Style F
Side Tapped Mounting
(NFPA Style MS4)
3
F
G
J
TN
SN + stroke
XT
NT thread,
ND deep
(4 mounting holes)
K
Dimensions C, F & G See also rod end dimensions, page 3 & mounting information, page 30
Bore
Ø
Rod
No.
E
EB
38.1
(11/2")
1
2
63.5
11.5
50.8
(2")
1
2
76.2
63.5
(21/2")
1
2
3
82.6
(31/4")
EE
EL
EO
ES
ET
F
G
J
K
ND
NT 2
R
SB 3
ST
G1/2
22.2
9.5
24
21
9.5
44.5
38.1
10
12
12
M10
41.4
11
12.7
14.3
G1/2
23.8
12.7
24
24
15.9
44.5
38.1
13
15
11
M12
52.1
14
19.1
88.9
14.3
G1/2
23.8
12.7
24
24
15.9
44.5
38.1
13
14
12
14
M16
64.8
22
25.4
1
2
3
114.3
17.5
G3/4
28.6
15.9
32
31
19.1
50.8
44.5
16
22
17
22
M20
82.6
22
25.4
101.6
(4")
1
2
3
127.0
17.5
G3/4
28.6
15.9
32
29
22.2
50.8
44.5
16
25
17
25
M24
97.0
26
31.8
127.0
(5")
1
2
3
4
165.1
23.8
G /4
19
28
25
28
28
M24
125.7
26
31.8
152.4
(6")
1
2
3
4
190.5
27.0
G1
42.9
22.2
45
45
25.4
57.2
57.2
22
44
31
44
38
M30
145.5
33
38.1
177.8
(7")
1
2
3
4
215.9
30.2
G11/4
46.0
25.4
50
48
25.4
69.9
69.9
24
54
28
54
44
M42
167.1
39
44.5
203.2
(8")
1
2
3
5
241.3
33.3
G11/2
50.8
28.6
50
48
25.4
76.2
76.2
27
57
38
57
44
M42
190.5
39
44.5
(BSPP)
3
38.1
19.1
38
38
22.2
50.8
44.5
All dimensions are in millimetres unless otherwise stated.
16
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Foot Mountings 38.1 - 203.2mm bores
ZE + stroke
XE + stroke
P + stroke
LB + stroke
Y
E
EE
1
E
2
4
-0.15
ET
F
Style G
Side End Lug
(NFPA Style MS7)
G
EL
EO
3
R
K
J
EL
ES
EO
E/2 -0.20
0.2 - 0.4
EB (4 holes)
ES
SE + stroke
See Note 1
Notes
1 Consider the use of a thrust key with this mounting – see page 30
2 Tapped mounting holes are metric (coarse pitch series)
3 Upper surfaces of lugs are machined for socket head screws
4 Style C cylinders can be supplied with the cylinder ports arranged for mounting and sealing to a manifold surface – see page 31
Dimensions C, F & G Continued
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
9.5
18.0
50.8
(2")
1
2
12.7
63.5
(21/2")
1
2
3
82.6
(31/4")
TN
TS
+ Stroke
US
XS
XT
Y
82.6
101.6
34.9
44.5
50.8
60.3
49
59
127.0
75
171.5
23.8
101.6
127.0
47.6
54.0
60.3
66.7
59
65
133.4
75
17.5
32.0
123.8
158.8
52.4
65.1
58.7
60.3
73.0
66.7
59
71
65
136.5
1
2
3
17.5
38.1
149.2
184.2
58.7
68.3
65.1
69.9
79.4
76.2
68
79
76
101.6
(4")
1
2
3
22.2
52.4
171.5
215.9
69.9
79.4
73.0
76.2
85.7
79.4
76
86
79
127.0
(5")
1
2
3
4
22.2
74.6
209.6
254.0
73.0
79.4
79.4
79.4
79.4
85.7
85.7
85.7
79
86
86
86
181.0
110
257.2
152.4
(6")
1
2
3
4
28.6
84.1
247.7
304.8
85.7
88.9
86
212.7
130
177.8
(7")
1
2
3
4
34.9
90.0
285.8
355.6
92.1
96.8
92
241.3
203.2
(8")
1
2
3
5
34.9
105.0
311.2
381.0
92.1
100.0
94
266.7
SW
SS
XE
ZB max
ZE
73.0
98.4
165.1
174.6
152.4
161.9
174.6
184.2
181.0
73.0
92.1
176.2
182.6
163.5
169.9
188.9
195.3
78
184.2
76.2
85.7
179.4
192.1
185.7
166.7
179.4
173.3
192.1
204.8
198.4
158.8
90
215.9
88.9
104.8
209.6
219.1
215.9
195.3
204.8
201.6
225.4
235.0
231.8
168.3
97
225.4
95.3
101.6
222.3
231.8
225.4
208.0
217.5
211.1
238.1
247.7
241.3
108.0
114.3
247.7
254.0
254.0
254.0
230.2
236.5
236.5
236.5
266.7
273.1
273.1
273.1
298.5
130.2
130.2
287.3
266.7
309.6
146
333.4
149.2
146.1
319.1
298.5
344.5
168
368.3
168.3
171.5
349.3
325.4
377.8
LB
P
SE
SN
All dimensions are in millimetres unless otherwise stated.
17
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Pivot Mountings 38.1 - 203.2mm bores
E
ZC + stroke
P + stroke
Y
E
1
K
2
CD
EE
4
MR
LR
3
Style BB
Cap Fixed Clevis
(NFPA Style MP1)
CW
CB
G
CW
J
F
XC + stroke
See Note 1
LB + stroke
Y
E
P + stroke
EE
K
EF
1
MS
4º
2
4 CN
E
4º
EX
LS
3
F
EP
Style SBa
Spherical Bearing
(ISO 6982 and CETOP RP88H)
J
G
XO + stroke
XV + stroke
See Notes 2, 3, 4, 5
Dimensions BB & SBa See also rod end dimensions, page 3 & mounting information, page 30
EE
EF
(BSPP)
max
63.5
G1/2
15.9
76.2
32
15.9
25.43
40
51.6
34.95
1
2
3
4
65.0
152.4
(6")
1
2
3
4
177.8
(7")
203.2
(8")
Bore
Ø
Rod
No.
CB
CD -0.05
38.1
(11/2")
1
2
19.8
12.73
50.8
(2")
1
2
32.5
63.5
(21/2")
1
2
3
82.6
(31/4")
+0.00
CN
CW
E
EP
EX
F
G
J
20
12.7
25
20
18
9.5
44.5
38.1
19.08
25
G1/2
31
25
22
15.9
44.5
38.1
32.5
19.08
88.9
G1/2
38
32
28
15.9
44.5
38.1
1
2
3
38.9
19.1
114.3
G3/4
49
40
35
19.1
50.8
44.5
101.6
(4")
1
2
3
50
25.4
127.0
G3/4
59
50
40
22.2
50.8
44.5
127.0
(5")
44.48
63
31.8
165.1
G3/4
71
63
52
22.2
50.8
44.5
65.0
50.83
80
31.8
190.5
G1
90
80
60
25.4
57.2
57.2
1
2
3
4
77.8
63.53
–
38.1
215.9
G11/4
–
–
–
25.4
69.9
69.9
1
2
3
5
77.8
76.23
–
38.1
241.3
G11/2
–
–
–
25.4
76.2
76.2
H7
All dimensions are in millimetres unless otherwise stated.
18
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Pivot Mountings 38.1 - 203.2mm bores
Notes
1 Supplied complete with pivot pin
2 Maximum pressure rating 160 bar
3 For matching pin sizes specify rod end Style 7, see pages 3 and 29
4 Pivot pin not supplied
5 For spherical bearing mountings on cylinders above 152.4mm (6”) bore, please consult the factory
Dimensions BB & SBa Continued
MS
+ Stroke
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
10
14.3
23
15.9
50.8
(2")
1
2
13
25.4
26
63.5
(21/2")
1
2
3
13
23.8
82.6
(31/4")
1
2
3
16
101.6
(4")
1
2
3
16
127.0
(5")
1
2
3
4
152.4
(6")
1
2
3
4
22
58.7
78
60.3
93
86
212.7
177.8
(7")
1
2
3
4
24
69.9
–
73.0
–
92
203.2
(8")
1
2
3
5
27
82.6
–
79.4
–
94
K
19
LR
LS
MR
max
Y
LB
P
XC
XO 5
XV
ZC
–
182.5
–
234.5
177.8
187.4
25
49
59
127.0
75
161.9
171.5
23.8
31
59
65
133.4
75
184.2
190.5
182.5
188.8
247.5
253.8
208.0
214.3
32
23.8
38
59
71
65
136.5
78
187.3
200.0
193.7
–
217.2
210.8
–
297.2
290.8
211.1
223.8
217.5
31.8
41
30.2
50
68
79
76
158.8
90
219.1
228.6
225.4
–
240.6
237.4
–
337.6
334.4
249.3
258.8
255.6
44.5
50
41.3
61
76
86
79
168.3
97
247.7
257.2
250.8
–
266.2
259.9
–
386.2
379.9
289.0
298.4
292.1
71
79
86
86
86
110
266.7
273.1
273.1
273.1
–
282.9
282.9
–
–
422.9
422.9
–
320.7
327.1
327.1
327.1
130
308.0
–
358.3
–
358.3
–
538.3
–
538.3
368.3
241.3
146
349.3
–
–
422.3
266.7
168
381.0
–
–
460.4
52.4
62
54.0
181.0
All dimensions are in millimetres unless otherwise stated.
19
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Trunnion Mountings 38.1 - 203.2mm bores
ZB + stroke
P + stroke
LB + stroke
EE
Y
UT
1
R3.2
2 TD
E4
Style D
Head Trunnion
(NFPA Style MT1)
F
3
E
TL
K
J
G
TL
XG
ZB + stroke
P + stroke
Y
UT
LB + stroke
EE
1
R3.2
E 4
Style DB
Cap Trunnion
(NFPA Style MT2)
F
J
G
2 TD
3
E
TL
K
TL
XJ + stroke
Dimensions D, DB & DD See also rod end dimensions, page 3 & mounting information, page 30
Bore
Ø
Rod
No.
BD
E
38.1
(11/2")
1
2
31.8
63.5
50.8
(2")
1
2
38.1
63.5
(21/2")
1
2
3
82.6
(31/4")
EE
F
G
J
K
G1/2
9.5
44.5
38.1
10
76.2
G1/2
15.9
44.5
38.1
38.1
88.9
G1/2
15.9
44.5
1
2
3
50.8
114.3
G3/4
19.1
101.6
(4")
1
2
3
50.8
127.0
G3/4
127.0
(5")
1
2
3
4
50.8
165.1
152.4
(6")
1
2
3
4
76.2
177.8
(7")
1
2
3
4
203.2
(8")
1
2
3
5
TD
+0.00
-0.03
TL
TM
TY
25.40
25.4
76.2
69.9
13
34.93
34.9
88.9
82.6
38.1
13
34.93
34.9
101.6
95.2
50.8
44.5
16
44.45
44.5
127.0
120.7
22.2
50.8
44.5
16
44.45
44.5
139.7
133.4
G3/4
22.2
50.8
44.5
19
44.45
44.5
177.8
171.5
190.5
G1
25.4
57.2
57.2
22
50.8
50.8
215.9
196.9
76.2
215.9
G11/4
25.4
69.9
69.9
24
63.5
63.5
247.7
222.3
88.9
241.3
G11/2
25.4
76.2
76.2
27
76.2
76.2
279.4
247.7
(BSPP)
All dimensions are in millimetres unless otherwise stated.
20
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Trunnion Mountings 38.1 - 203.2mm bores
ZB + stroke
P + stroke
LB + stroke
EE
BD
Y
See Notes 1, 2, 3
UM
E
1
R3.2
2 TD UW
TY E 4
Style DD
Intermediate Fixed Trunnion
(NFPA Style MT4)
F
J
G
K
TL
3
TM
TL
XI
Notes
1 Note the minimum strokes from the table below
2 XI dimension to be specified by customer, note minimum dimension
3 A one-piece trunnion is fitted to 38.1mm (11/2"), 50.8mm (2") and 63.5mm (21/2") bore cylinders
Dimensions D, DB & DD Continued
Style DD
min stroke
UW 3
XG
Min. 2
XI
Y
114.3
–
47.6
57.2
85.7
95.3
49
59
0.0
158.8
146.1
–
57.2
63.5
98.4
104.8
59
65
1
2
3
171.5
158.8
–
57.2
69.9
63.5
98.4
111.1
104.8
82.6
(31/4")
1
2
3
215.9
203.2
171.5
66.7
76.2
73.0
101.6
(4")
1
2
3
228.6
215.9
184.2
127.0
(5")
1
2
3
4
266.7
254.0
152.4
(6")
1
2
3
4
317.5
177.8
(7")
1
2
3
4
203.2
(8")
1
2
3
5
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
127.0
50.8
(2")
1
2
63.5
(21/2")
UM
UT
+ Stroke
LB
P
XJ
ZB max
127.0
75
123.8
133.4
152.4
161.9
3.2
133.4
75
133.4
139.7
163.5
169.9
59
71
65
0.0
136.5
78
136.5
149.2
142.9
166.7
179.4
173.3
117.5
127.0
123.8
68
79
76
6.4
158.8
90
158.8
168.3
165.1
195.3
204.8
201.6
73.0
82.6
76.2
123.8
133.4
127.0
76
86
79
0.0
168.3
97
171.5
181.0
174.6
208.0
217.5
211.1
228.6
76.2
82.6
82.6
82.6
127.0
133.4
133.4
133.4
79
86
86
86
0.0
181.0
110
187.3
193.7
193.7
193.7
230.2
236.5
236.5
236.5
292.1
260.4
85.7
152.4
86
3.2
212.7
130
212.7
266.7
374.7
342.9
292.1
92.1
165.1
92
0.0
241.3
146
238.1
298.5
431.8
393.7
323.9
95.3
177.8
94
0.0
266.7
168
260.4
325.4
All dimensions are in millimetres unless otherwise stated.
21
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Head Flange Mountings 254.0 - 304.8mm bores
UF
E
ZB + stroke
P + stroke
Y
22.2 max
EE
1
E 4
F
G
Style J
Head Rectangular Flange
(NFPA Style MF1)
J
2 R
FB
(4 holes)
3
TF
K
LG + stroke
See Notes 1, 2, 3, 4
UF
E
ZB + stroke
P + stroke
Y
22.2 max
1
EE
UF E
Style JB
Head Square Flange
(NFPA Style MF5)
2
4
G
J
FB
(8 holes)
3
R
TF
F
K
LG + stroke
See Notes 1, 2, 4
See Notes 1, 2, 4
ZB + stroke
Y
R TF
P + stroke
UF
LG + stroke
EE
E
1
E 4
Style JJ
Rectangular Head
(NFPA Style ME5)
RT
2
3
TF
K
22.2 max
FB
(4 holes)
J
G
R
Dimensions J, JB & JJ See also rod end dimensions, page 40 & mounting information, page 30
Bore
Ø
Rod
No.
E
254.0
(10")
1
2
320.7
304.8
(12")
1
2
377.8
EE 4
F
FB
G
J
K
R
RT
TF
UF
Y
G2
42.9
46.0
93.7
93.7
39
244.3
25.4
28.6
403.2
482.6
G21/2
49.2
52.4
112.7
112.7
See
note 2
290.8
33.3
28.6
469.9
558.8
(BSPP)
+ Stroke
LG
P
ZB max
120.7
127.0
308.0
215.9
422.3
428.6
136.5
142.9
368.3
257.2
449.3
455.6
Notes
2 Tie rod nuts are flush with cap on 304.8mm (12”) cylinders
1 The dimensional drawings above
show 254mm (10”) bore models fitted
with four tie rods, but can also be
used to determine dimensions for 304.8mm
(12”) bore models fitted with 16 tie rods
3 For maximum pressure ratings, see page 32
4 Flange ports to ISO 6162 are also available – see page 35
All dimensions are in millimetres unless otherwise stated.
22
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Cap Flange Mountings 254.0 - 304.8mm bores
E
1
22.2 max
K
2
E
ZF + stroke
P + stroke
EE
Y
4 R
FB
(4 holes)
3
TF
UF
Style H
Cap Rectangular Flange
(NFPA Style MF2)
J
G
F
LG + stroke
XF + stroke
See Notes 1, 2, 3, 4
UF
22.2 max
E
1
ZF + stroke
P + stroke
EE
Y
K
UF 2
E
Style HB
Cap Square Flange
(NFPA Style MF6)
4 R TF
3
R
TF
FB
(8 holes)
J
G
F
LG + stroke
XF + stroke
See Notes 1, 2, 4
LG + stroke
UF
22.2 max
Y
K
E
1
R 2
EE
4 E
3
TF
FB
(4 holes)
Style HH
Rectangular Cap
(NFPA Style ME6)
P + stroke
J
G
XF + stroke
See Notes 1, 2, 4
Dimensions H, HB & HH See also rod end dimensions, page 40 & mounting information, page 30
Bore
Ø
Rod
No.
E
254.0
(10")
1
2
320.7
304.8
(12")
1
2
377.8
EE 4
F
FB
G
J
K
R
TF
UF
Y
G2
42.9
46.0
93.7
93.7
39
244.3
403.2
482.6
G21/2
49.2
52.4
112.7
112.7
See
note 2
290.8
469.9
558.8
(BSPP)
+ Stroke
LG
P
XF
ZF
120.7
127.0
308.0
215.9
382.6
388.9
425.5
431.8
136.5
142.9
368.3
257.2
449.3
455.6
498.5
504.8
Notes
2 Tie rod nuts are flush with head on 304.8mm (12”) cylinders
1 The dimensional drawings above
show 254mm (10”) bore models fitted
with four tie rods, but can also be
used to determine dimensions for 304.8mm
(12”) bore models fitted with 16 tie rods
3 For maximum pressure ratings, see page 32
4 Flange ports to ISO 6162 are also available – see page 35
All dimensions are in millimetres unless otherwise stated.
23
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Trunnion Mountings 254.0 - 304.8mm bores
ZB + stroke
P + stroke
LG + stroke
EE
Y
UT
1
R3.2
E
Style D
Head Trunnion
(NFPA Style MT1)
J
G
2 TD
4
3
E
TL
K
22.2 max
TL
XG
See Notes 1, 2, 4
ZB + stroke
P + stroke
Y
LG + stroke
EE
UT
1
R3.2
E4
Style DB
Cap Trunnion
(NFPA Style MT2)
J
G
2 TD
3
E
TL
K
TL
XJ + stroke
See Notes 1, 2, 4
ZB + stroke
P + stroke
LG + stroke
EE
BD
Y
22.2 max
See Notes 1, 2, 3, 4
UM
E
1
R3.2
E
TY
UW
2 TD
4
22.2 max
Style DD
Intermediate Fixed Trunnion
(NFPA Style MT4)
K
J
G
3
TM
TL
TL
XI
Dimensions D, DB, & DD See also rod end dimensions, page 40 & mounting information, page 30
Bore
Ø
Rod
No.
254.0
(10")
1
2
114.3 320.7
304.8
(12")
1
2
139.7 377.8 G21/2 112.7
BD
E
EE 4
(BSPP)
G2
+0.000
G&J
K
TD -0.025
93.7
39
88.9
See
note 2
101.6
Min. 3
XI
XG
&Y
88.9 355.6 330.2 533.4 498.5 444.5
225.4
231.8
120.7
127.0
101.6 419.1 393.7 622.3 581.0 527.1
263.5
269.9
136.5
142.9
TL
TM
TY
UM
UT
UW
+ Stroke
LG
P
XJ
ZB max
308.0 215.9
336.6
342.9
421.6
427.9
368.3 257.2
393.7
400.0
449.3
455.6
Notes
2 Tie rod nuts are flush with head and cap on 304.8mm (12”) cylinders
1 The dimensional drawings above
show 254mm (10”) bore models fitted
with four tie rods, but can also be
used to determine dimensions for 304.8mm
(12”) bore models fitted with 16 tie rods
3 Dimension XI to be specified by customer
4 Flange ports to ISO 6162 are also available – see page 35
All dimensions are in millimetres unless otherwise stated.
24
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Side Lug & Clevis 254.0 - 304.8mm bores
See Notes 1, 2, 3, 4
ZB + stroke
P + stroke
LG + stroke
EE
Y
22.2 max
1
E
4
2
E/2 -0.15
-0.20
ST
Style C
Side Lug
(NFPA Style MS2)
J
G
E
TS
SW
ZC + stroke
P + stroke
Y
K
2
SW
US
E
1
22.2 max
3
E
K
SW
SS + stroke
XS
SB
(4 holes)
CD
EE
4
MR
LR
3
Style BB
Cap Fixed Clevis
(NFPA Style MP1)
CW
CB
G
CW
J
XC + stroke
See Notes 1, 2, 4, 5
Dimensions C & BB See also rod end dimensions, page 40 & mounting information, page 30
Bore
Ø
Rod
No.
254.0
(10")
1
2
101.6 88.93 50.8 320.7
304.8
(12")
1
2
114.3 101.63 57.2 377.8 G21/2 112.7
+0.00
CB CD-0.08 CW
E
EE 4
(BSPP)
G
&J
K
G2
93.7
39
LR MR SB ST SW
TS
US
98.4 90.0 39 57.2 41.3 403.2 485.8
XS
+ Stroke
Y
LG
P
SS
XC ZB max ZC
115.9 120.7
483.4 421.6 573.1
308.0 215.9 225.4
122.2 127.0
490.5 427.9 579.4
See
131.8 136.5
563.6 449.3 665.2
111.1 111.1 39 76.2 50.8 479.4 581.0
368.3 257.2 266.7
note 2
138.1 142.9
569.9 455.6 671.5
Notes
2 Tie rod nuts are flush with head and cap on 304.8mm (12”) cylinders
1 The dimensional drawings above
show 254mm (10”) bore models fitted
with four tie rods, but can also be
used to determine dimensions for 304.8mm
(12”) bore models fitted with 16 tie rods
3 Style C cylinders can be supplied with the cylinder ports arranged
for mounting and sealing to a manifold surface – see page 31
4 Flange ports to ISO 6162 are also available – see page 35
5 Supplied complete with pivot pin
All dimensions are in millimetres unless otherwise stated.
25
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Double Rod Cylinders
ZM + 2 x stroke
ZL + stroke
P + stroke
LD + stroke
Y
ZM + 2 x stroke
ZL + stroke
P + stroke
LG + stroke
Y
EE
EE
MM
MM
F
XS
G
G
S*K + stroke
Double Rod Cylinders
38.1 to 203.2mm Bores
F
K
G
Available with Styles TB, TD,
J, JB, JJ, C, F, D, DD, and G
Double Rod Cylinders
254 and 304.8mm Bores
Mounting Styles and Codes
Double rod cylinders are denoted by a ‘K’ in the model code,
shown on page 41.
Bore Rod
Ø
No.
MM
Rod
Diameter
Dimensions
38.1
(11/2")
1
2
50.8
(2")
To obtain dimensional information for double rod cylinders,
first select the desired mounting style by referring to the
corresponding single rod models shown on the preceding
pages. Dimensions for the appropriate single rod model should
be supplemented by those from the table opposite to provide a
full set of dimensions.
Rod Strength
Double rod cylinders employ two separate piston rods, with
one screwed into the end of the other within the piston rod
assembly. As a result, one piston rod is stronger than the
other. The stronger rod is identified by the letter ‘K’ stamped
on its end, and its pressure limitations with a 4:1 design factor
are identical to those shown in the table on page 32 for the
equivalent single rod assembly. The weaker rod should always
be used for the lighter duty. Pressure limitations for the weaker
rod in pull applications at a 4:1 design factor are also identical to
those on page 32, except for the bore sizes shown in the table
below.
Bore Ø
Rod Diameter
4 : 1 Design Factor
(bar)
63.5 (21/2")
25.4 (1")
95
82.6 (3 /4")
34.9 (1 /8")
115
1
G
3
K
SSK + stroke
XS
Available with Styles J, JB,
JJ, C, D, and DD
+ 2x
Stroke
+ Stroke
LD 1
LG 2
ZL
SEK 3
SNK 4
SSK 5
ZM
15.9 ( /8")
25.4 (1")
142.9
168.3
177.8
187.3
73.0
104.8
174.6
193.7
1
2
25.4 (1")
34.9 (13/8")
155.6
185.7
192.1
203.3
73.0
98.4
193.7
206.4
63.5
(21/2")
1
2
3
25.4 (1")
44.5 (13/4")
34.9 (13/8")
158.8
188.9
201.6
195.2
206.4
76.2
92.1
196.9
222.3
209.6
82.6
(31/4")
1
2
3
34.9 (13/8")
50.8 (2")
44.5 (13/4")
184.2
220.7
230.2
227.0
241.4
88.9
111.1
228.6
247.7
241.3
101.6
(4")
1
2
3
44.5 (13/4")
63.5 (21/2")
50.8 (2")
196.9
236.5
246.1
239.7
254.0
95.3
108.0
247.7
266.7
254.0
127.0
(5")
1
2
3
4
50.8 (2")
88.9 (31/2")
63.5 (21/2")
76.2 (3")
209.6
258.8
265.1
265.1
265.1
285.7
108.0
120.7
266.7
279.4
279.4
279.4
152.4
(6")
All
All
238.1
292.1
323.9
123.8
130.2
301.6
177.8
(7")
All
All
266.7
323.9
358.7
136.5
146.1
330.2
203.2
All
(8")
All
292.1
350.8
393.7
156.6
171.5
355.6
254.0
(10")
304.8
(12")
5
1
127.0 (5")
308.0
422.3
–
–
225.4
457.2
1
139.7
(51/2")
368.3
449.3
–
–
266.7
532.3
Use LD dimensions for 38.1mm to 203.2mm (11/2” to 8”) bore sizes
Use LG dimensions for 254.0mm & 304.8mm (10” & 12”) bore sizes
3
SEK dimensions apply to mounting style KG only
4
SNK dimensions apply to mounting style KF only
5
SSK dimensions apply to mounting style KC only
1
Combination Rods
2
Double rod cylinders with rods of differing rod diameters are
also available. Please contact the factory for details.
Cushioning
Double rod cylinders can be supplied with cushions at either
or both ends. Cushioning requirements should be specified by
inserting a ‘C’ in the ordering code ­– see page 41. Double rod
cylinders with optional cushioning are supplied with floating
cushion sleeves at both ends.
Style 9 Rod Ends
If a stroke of less than 25mm on bore sizes up to 82.6mm (31/4”),
or a stroke of less than 100mm on bore sizes of 101.6mm (4”)
and over, is required, where Style 9 rod ends are required at
both ends, please consult the factory.
All dimensions are in millimetres unless otherwise stated.
26
Parker Hannifin
Cylinder Division
Europe
Accessories
Tie Rod Cylinders
2H Series
Accessory Selection
Load Capacity
Catalogue HY07-1110/UK
Accessories for the rod end of a cylinder are selected by
reference to the rod end thread, shown on pages 3 and 40,
while accessories for use at the cap end are selected by
cylinder bore size.
The load capacities of the accessories shown on these pages
is the recommended maximum load based on a 4:1 factor of
safety in tension. (Pivot pin is rated in shear). Before specifying,
compare the actual load or the pull force at maximum operating
pressure of the cylinder with the load capacity of the accessory
you plan to use. If the load or pull force of the cylinder exceeds
the load capacity of the accessory, please consult the factory.
Rod and Cap End Accessories
Rod End – rod clevis, eye bracket and pivot pin
– plain rod eye, clevis bracket and pivot pin
– rod eye with spherical bearing
Pivot Pin Diameters
Cap End – eye bracket for style BB mounting
(Note: pivot pin is supplied with cylinder)
Rod End Fatigue
Fatigue failure of the rod end is minimised by using a shouldered
rod end, ie: Style 4, and tightening accessories securely against
the rod shoulder. Where this is not the case, derating of the
maximum working pressure may be required – please consult
the factory.
Rod Clevis, Eye Bracket and Pivot Pin Thread
KK
Rod
Clevis
Eye
Bracket
M10x1.5
50940G
M12x1.5
50941G
M20x1.5
To obtain the same diameter of pivot pin at the rod end and cap
end of a style BB clevis-mounted cylinder fitted with a rod clevis
or plain rod eye, a no. 1 rod should be specified.
Pivot pins of the same diameter can be obtained at each end of
a style SBa cylinder fitted with a rod end spherical bearing by
specifying a style 7 rod end and nos. 2, 3 or 4 rods, as indicated
in the table on page 3.
Plain Rod Eye, Clevis Bracket and Pivot Pin Pivot
Pin
Nominal
Force kN
69195
68368
69195
68368
50942G
96196
M22x1.5
50943G
M26x1.5
Mass
kg
Thread
KK
Plain
Rod Eye
18.3
0.7
M10x1.5
69089G
18.3
0.7
M12x1.5
69090G
68369
46.8
2.3
M20x1.5
69091G
85361 1
68370
83.8
5.2
M22x1.5
50944G
85361 1
68370
91.0
5.1
M26x1.5
M33x2
50945G
69198
68371
94.5
9.9
M33x2
M39x2
50946G
85362 1
68372
203.3
19.5
M45x2
50947G
85363 1
68373
312.1
28.6
M48x2
50948G
85363 1
68373
312.1
M58x2
50949G
85364 1
68374
M64x2
50950G
85365 1
68375
M68x2
50951G
85365 1
68375
M76x2
50952G
73538
73545
Clevis
Bracket
Pivot
Pin
Nominal
Force kN
Mass
69205
68368
22.3
1.3
69205
68368
25.4
1.3
69206
68369
54.0
3.2
69092G
69207
68370
58.0
6.6
69093G
69207
68370
85.6
6.6
69094G
69208
68371
149.4
12.7
M39x2
69095G
69209
68372
151.6
23.4
M45x2
69096G
69210
69215
147.2
41.1
28.5
M48x2
69097G
69210
69215
147.2
41.5
420.0
48.4
M58x2
69098G
69211
68374
155.6
51.2
420.0
54.9
M64x2
69099G
69212
68375
150.7
65.2
543.6
63.1
M68x2
69100G
69213
69216
164.6
69.5
256.0
104.8
M76x2
73536G
73542
73545
372.3
126.7
kg
M90x2
50953G
73539
73547
334.4
157.8
M90x2
73437G
73542
73545
372.3
124.0
M100x2
50954G
73539
73547
334.4
156.6
M100x2
73438G
73543
82181
457.5
180.7
M110x2
–
–
–
–
–
M110x2
73439G
73544
73547
483.4
173.5
1
Cylinder accessory dimensions conform to NFPA recommended
standard, NFPA/T3.6.8.R1 - 1984
Cap End Eye Bracket for Style BB Cylinders
Rod Eye with Spherical Bearing
Torque Load
Mass
Nm
kg
145239
13
0.4
145240
13
0.7
M27x2
145241
32
1.2
M33x2
145242
32
2.1
M42x2
145243
64
4.4
M48x2
145244
80
7.6
M64x3
145245
195
14.5
Thread
KK
Part No.
M16x1.5
M20x1.5
Bore
Ø
Eye Bracket
Part No.
Nominal Force
kN
kg
38.1 (11/2")
69195
18.3
0.4
50.8 (2")
69196
46.8
1.5
63.5 (21/2")
69196
46.8
1.5
82.6 (31/4")
85361 1
91.0
3.4
101.6 (4")
69198
94.5
5.6
127.0 (5")
85362 1
220.6
11.1
152.4 (6")
85363 1
312.1
17.0
177.8 (7")
85364 1
420.0
27.4
203.2 (8")
85365 1
543.6
35.8
254.0 (10")
73538
256.0
55.6
304.8 (12")
73539
334.4
84.3
All dimensions are in millimetres unless otherwise stated.
27
Mass
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Accessories
Rod Clevis, Eye Bracket and Pivot Pin
Rod Clevis Dimensions
Part
No.
A
CB
CD +0.05
CE
CW
ER
KK
Nominal
Force kN
Mass
50940G
19.1
19.8
12.70
38.1
12.7
12.7
M10x1.5
18.9
0.2
+0.10
Rod Clevis (Female Clevis)
kg
50941G
19.1
19.8
12.70
38.1
12.7
12.7
M12x1.5
21.9
0.2
50942G
28.6
32.6
19.05
54.0
15.9
19.1
M20x1.5
49.9
0.6
50943G
41.3
38.9
25.40
74.6
19.1
25.4
M22x1.5
83.8
1.3
50944G
41.3
38.9
25.40
74.6
19.1
25.4
M26x1.5
96.7
1.3
50945G
50.8
51.6
34.93
95.3
25.4
34.9
M33x2
149.4
3.1
6.0
50946G
57.2
64.7
44.45
114.3
31.8
44.5
M39x2
203.3
50947G
76.2
64.7
50.80
139.7
31.8
50.8
M45x2
317.9
8.4
50948G
76.2
64.7
50.80
139.7
31.8
50.8
M48x2
341.6
8.3
50949G
88.9
77.4
63.50
165.1
38.1
63.5
M58x2
480.2
15.1
50950G
88.9
77.4
76.20
171.5
38.1
69.9
M64x2
535.1
19.0
18.7
50951G
88.9
77.4
76.20
171.5
38.1
69.9
M68x2
589.9
50952G
88.9
102.8
88.90
196.9
50.8
88.9
M76x2
1048.8
34.1
50953G
101.6
116.0
101.60
223.8
57.2
101.6
M90x2
1292.2
49.8
50954G
101.6
116.0
101.60
223.8
57.2
101.6
M100x2
1480.0
48.6
CW
CB
CW
ER
CD
CE
A
KK
Eye Bracket Dimensions
Part
No.
69195
1
+0.10
CB CD +0.05 DD
19.1
Nominal Mass
Force kN kg
E
F
FL
LR
M
MR
R
28.6
19.1
12.7
14.3
41.4
18.3
12.70
10.3
63.5
9.5
88.9
Eye Bracket
MR
0.4
69196
31.8
19.05
13.5
15.9
47.6
31.8
19.1
22.2
64.8
46.8
1.5
85361 1
38.1
25.40
16.7 114.3 22.2
60.3
38.1
25.4
31.8
82.6
91.0
3.4
69198
50.8
34.93
16.7 127.0 22.2
76.2
54.0
34.9
41.3
97.0
94.5
5.6
85362 1
63.5
44.45
23.0 165.1 28.6
85.7
57.2
44.5
54.0 125.7
220.6
11.1
85363 1
63.5
50.80
27.0 190.5 38.1 101.6 63.5
50.8
61.9 145.5
312.1
17.0
85364 1
76.2
63.50
30.2 215.9 44.5 120.6 76.2
63.5
76.2 167.1
420.0
27.4
35.8
85365 1
76.2
76.20
33.3 241.3 50.8 133.3 82.6
69.9
82.6 190.5
543.6
73538
101.6
88.90
46.0 320.7 42.9 144.5 101.6 88.9
95.3 244.3
256.0
55.6
73539
114.3 101.60
52.4 377.8 49.2 163.5 114.3 101.6 108.0 290.8
334.4
84.3
CB
M
CD
25°
DD
(x4)
FL
F
LR
R
E
R
E
Cylinder accessory dimensions conform to NFPA recommended standard,
NFPA/T3.6.8.R1 - 1984
Pivot Pin for Clevis Bracket & Eye Bracket
Part
No.
CD-0.05
CL
G
Nominal
Force kN
68368
12.73
45.8
56
38.4
0.1
68369
19.08
64.9
75
86.1
0.2
0.5
+0.00
Mass
kg
68370
25.43
77.4
88
152.9
68371
34.95
102.9
115
289.8
1.2
68372
44.48
128.3
143
469.1
2.4
68373
50.83
129.2
145
612.7
3.2
69215
50.83
140.9
158
612.7
3.5
68374
63.53
154.6
171
957.4
5.9
68375
76.23
154.2
173
1378.7
8.6
69216
76.23
167.2
185
1378.7
9.2
73545
88.93
205.2
225
1876.8
15.2
82181
101.63
219.8
254
2522.9
22.4
73547
101.63
231.2
266.7
2522.9
23.5
Pivot Pin for Clevis Bracket
& Eye Bracket
G
CL
CD
All dimensions are in millimetres unless otherwise stated.
28
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Accessories
Plain Rod Eye, Clevis Bracket and Pivot Pin
Plain Rod Eye Dimensions
Part
No.
A
min.
CA
CB
CD+0.05
ER
KK
Nominal
Force kN
Mass
69089G
19.1
38.1
19.1
12.70
18.3
M10x1.5
22.3
0.2
+0.10
Plain Rod Eye
kg
69090G
19.1
38.1
19.1
12.70
18.3
M12x1.5
25.4
0.2
69091G
28.6
52.4
31.8
19.05
27.0
M20x1.5
54.0
0.5
69092G
28.6
60.3
38.1
25.40
36.5
M22x1.5
58.0
1.1
69093G
41.3
71.4
38.1
25.40
36.5
M26x1.5
96.8
1.1
69094G
50.8
87.3
50.8
34.93
50.0
M33x2
149.4
2.6
69095G
57.2
101.6
63.5
44.45
63.5
M39x2
200.6
5.1
69096G
57.2
111.1
63.5
50.80
72.2
M45x2
238.6
6.4
69097G
76.2
127.0
63.5
50.80
72.2
M48x2
334.4
6.8
69098G
88.9
147.6
76.2
63.50
90.5
M58x2
440.1
12.1
69099G
88.9
155.6
76.2
76.20
108.0
M64x2
490.5
16.0
69100G
92.1
165.1
88.9
76.20
108.0
M68x2
549.8
19.6
73536G
101.6
193.7
101.6
88.90
126.2
M76x2
719.3
31.1
73437G
127.0
193.7
101.6
88.90
126.2
M90x2
969.0
28.4
73438G
139.7
231.8
114.3
101.60
144.5
M100x2
1220.9
42.5
73439G
139.7
231.8
127.0
101.60
144.5
M110x2
1375.6
48.4
CD
CD
CB
ER
CD
CD
CA
A
min.
KK
Clevis Bracket
CW
MR
CB
CW
M
Clevis Bracket Dimensions
Part
No.
+0.10
CB CD+0.05 CW DD
CD
25°
FL
DD
(x4)
F
E
F
FL
LR
M
MR
LR
Nominal Mass
Force kN kg
R
69205
19.8
12.70
12.7 10.3 88.9 12.7 38.1 19.1 12.7 15.9 64.8
32.6
1.0
69206
32.6
19.05
15.9 13.5 127.0 15.9 47.6 30.2 19.1 23.0 97.0
62.4
2.5
69207
38.9
25.40
19.1 16.7 165.1 19.1 57.2 38.1 25.4 31.8 125.7
85.6
5.0
69208
51.6
34.93
25.4 16.7 190.5 22.2 76.2 50.8 34.9 42.1 145.5
164.6
8.8
69209
64.7
44.45
31.8 23.0 241.3 22.2 92.1 69.9 44.5 56.4 190.5
151.6
15.9
69210
64.7
50.80
38.1 27.0 323.9 25.4 108.0 81.0 57.2 70.6 238.8
147.2
31.2
69211
77.4
63.50
38.1 30.2 323.9 25.4 114.3 88.9 63.5 79.4 238.8
155.6
33.2
69212
77.4
76.20
38.1 33.3 323.9 25.4 152.4 108.0 76.2 91.3 238.8
150.7
40.7
69213
90.1
76.20
38.1 33.3 323.9 25.4 152.4 108.0 76.2 91.3 238.8
164.6
40.7
73542
102.8
88.90
50.8 46.0 393.7 42.9 169.9 127.0 88.9 104.8 304.8
372.3
80.4
73543
116.0 101.60 50.8 52.4 444.5 49.2 195.3 146.1 101.6 123.8 349.3
457.5
115.8
73544
128.2 101.60 50.8 52.4 444.5 49.2 195.3 146.1 101.6 123.8 349.3
483.4
101.6
R
E
R
E
Rod Eye with Spherical Bearing
– ISO 6982
C
EN
EF
z
CN
LF
CH
AX
KK
b
Rod Eye with Spherical Bearing Dimensions – ISO 6982
CN
Part
No.
AX
min.
b
C
max.
CH
145239
23
25
50
52
145240
29
30
62
65
25
145241
37
38
76
80
32
Clamp screw
torque (Nm)
Mass
13
0.4
EF
max.
EN
KK
H7
h12
(Style 7)
20
25
20
M16x1.5
32
25
M20x1.5
27
13
0.7
40
32
M27x2
32
32
1.2
LF
Z
22
4°
kg
145242
46
47
97
97
40
50
40
M33x2
41
145243
57
58
118
120
50
63
50
M42x2
50
145244
64
70
142
140
63
71
63
M48x2
62
80
7.6
145245
86
90
180
180
80
90
80
M64x3
78
195
14.5
All dimensions are in millimetres unless otherwise stated.
29
Parker Hannifin
Cylinder Division
Europe
32
2.1
64
4.4
Mounting Information
Tie Rod Cylinders
2H Series
Mounting Styles
Trunnion Mounted Cylinders
Catalogue HY07-1110/UK
General guidance for the selection of mounting styles is given
on page 9. The notes which follow provide information for use in
specific applications.
Mounting Bolts
Parker recommends that mounting bolts with a minimum strength
of ISO 898/1 grade 10.9 should be used for fixing cylinders
to the machine or base. This recommendation is of particular
importance where bolts are placed in tension or subjected to
shear forces. Mounting bolts should be torque loaded to their
manufacturer’s recommended figures.
Extended Tie Rods
The standard tie rod extension
for cylinders with mounting
styles TB, TC and TD is shown
as BB in dimension tables.
Longer or shorter extensions
can be supplied. Cylinders are
supplied with an additional set
of mounting nuts – see table.
Bore
Ø
The position of an intermediate fixed trunnion is fixed during
manufacture and its location must be specified at the time of
order.
Foot Mountings and Thrust Keys
The turning moment which results from the application of force
by a foot mounted cylinder must be resisted by secure mounting
and effective guidance of the load. A thrust key modification is
recommended to provide positive cylinder location.
Tie Rod Nuts
Tie rod mounting nuts, with
lubricated threads, should be
to a minimum strength of ISO
898/2 grade 10, torque loaded
to the figures shown.
Trunnions require lubricated pillow blocks with minimum bearing
clearances. Blocks should be aligned and mounted to eliminate
bending moments on the trunnion pins. Self-aligning mounts
must not be used to support the trunnions as bending forces
can be set up.
Tie Rod Nuts
Size
A/F
Torque
Nm min-max
38.1 (11/2")
14.3
25-27
50.8 (2")
19.1
60-65
63.5 (21/2")
19.1
60-65
82.6 (31/4")
23.8
160-165
101.6 (4")
23.8
175-180
127.0 (5")
33.4
420-425
152.4 (6")
38.1
715-735
177.8 (7")
42.9
1080-1100
203.2 (8")
47.6
1560-1580
254.0 (10")
–
3390-3410
304.8 (12")
–
715-735
Thrust key mountings eliminate the need for fitted bolts or
external keys on Styles C, F and G side mounted cylinders.
The gland retainer plate is
F
extended below the nominal
mounting surface to fit
into a keyway milled into
PD
the mounting surface of
the machine member. See
PA
Integral Key
‘Mounting Modifications’ in
FA
the order code, page 41.
Bore
Ø
F
Nom.
+0.0
+0.0
FA -0.075
PA -0.2
PD
Cylinders may be ordered with extended tie rods in addition
to another mounting style. The extended tie rods may then be
used for mounting other systems or machine components.
38.1 (11/2")
9.5
8
4.9
36.5
50.8 (2")
15.9
14
8.0
46.0
63.5 (21/2")
15.9
14
8.1
52.4
82.6 (31/4")
19.1
18
9.7
66.7
Flange Mounted Cylinders
101.6 (4")
22.2
22
11.2
74.6
127.0 (5")
22.2
22
11.2
93.7
152.4 (6")
25.4
25
12.7
108.0
177.8 (7")
25.4
25
12.7
120.7
203.2 (8")
25.4
25
12.7
133.4
The diameter of the rod gland extension (B) at the head end
can be used as a pilot to locate the cylinders in relation to the
machine. After alignment has been obtained, the flanges may
be drilled for pins or dowels to prevent movement.
Pivot Mountings
Pivot pins are supplied with style BB cap fixed clevis mounted
cylinders. Pivot pins are not supplied with the spherical bearing
mounting, style SBa, as the pin length will be determined by the
customer’s equipment.
Spherical Bearings
Where a spherical bearing mounting, style SBa, is specified
for the cylinder, a rod eye with spherical bearing should be
used at the rod end. The life of spherical bearings is influenced
by factors such as specific load, direction of load, angle of
oscillation, and type and frequency of lubrication. The maximum
pressure rating for spherical bearing cylinders is 160 bar. If
unusual operating conditions exist, please consult the factory.
Tie Rod Supports
To increase the resistance to buckling
of long stroke cylinders, tie rod
supports may be fitted. These move
the tie rods radially outwards and
allow longer than normal strokes to be used without the need for an additional mounting. Bore
Ø
38.1
Stroke (metres)
0.9 1.2 1.5 1.8 2.1 2.4 2.7 3.0 3.3 3.6 3.9 4.2
–
–
1
1
1
2
2
2
3
3
3
4
50.8
–
–
–
1
1
1
1
2
2
2
2
3
63.5
–
–
–
–
–
1
1
1
1
1
2
2
82.6
–
–
–
–
–
–
–
1
1
1
1
1
101.6
–
–
–
–
–
–
–
–
–
1
1
1
Number
of
supports
req'd.
Bore sizes above 101.6mm (4”) do not require tie rod supports.
All dimensions are in millimetres unless otherwise stated.
30
Parker Hannifin
Cylinder Division
Europe
Theoretical Push and Pull Forces
Tie Rod Cylinders
2H Series
Stroke Tolerances
Calculation of Cylinder Diameter
Catalogue HY07-1110/UK
Stroke length tolerances are required due to the build-up of
tolerances of piston, head, cap and cylinder body. Standard
production stroke tolerances are -0.4 to +0.8mm on all bore sizes
and stroke lengths. For closer tolerances, please specify the
required tolerance plus the operating temperature and pressure.
Stroke tolerances of less than 0.4mm are generally impracticable
due to the elasticity of cylinders and, in these cases, the use of a
stroke limiter should be considered – see page 8.
Manifold Ports
Side mounted cylinders (Style C) can be supplied with the
cylinder ports arranged for mounting and sealing to a manifold
surface. The ports are drilled and counterbored for the O-ring
seals provided. With these specifications, the mounting is
designated Style CM. Please consult the factory.
Compression or 'Push Applications
If the piston rod is in compression, use the ‘Push Force’ table:
1. Identify the operating pressure closest to that required.
2. In the same column, identify the force required to move the
load (always rounding up).
3. In the same row, look along to the cylinder bore required.
If the cylinder envelope dimensions are too large, increase the
operating pressure, if possible, and repeat the exercise.
Tension or 'Pull' Applications
If the rod is in tension, use the ‘Deduction for Pull Force’ table:
1. Follow the procedure for ‘push’ applications above.
2. Using the ‘Deduction for Pull Force’ table, identify the force
indicated according to the rod and pressure selected.
3. Deduct this from the original ‘push’ force. The resultant is the
net force available to move the load.
Y
P + Stroke
PK + Stroke Single Rod
Double Rod
Bore
Ø
Rod
No.
Y
±0.8
PK
±0.8
38.1
(11/2")
1
2
50.8
60.3
73.0
50.8
(2")
1
2
60.3
66.7
73.0
63.5
(21/2")
1
2
3
60.3
73.0
66.7
82.6
(31/4")
1
2
3
69.9
79.4
76.2
101.6
(4")
1
2
3
72.2
81.8
75.4
101.6
1
2
3
4
79.4
85.7
85.7
85.7
108.0
127.0
(5")
152.4
(6")
All
88.9
P
±0.8
73.0
EEM
19.1
If this force is not large enough, repeat the process with a higher
system operating pressure or larger cylinder diameter.
EEM
ED
ED
28.6
Parker
O-ring No.
Push Force
Bore
Ø
2-212
Piston
Area
76.2
88.9
130.2
76.2
88.9
103.2
108.0
123.8
19.1
19.1
25.4
25.4
25.4
31.8
28.6
28.6
34.9
34.9
34.9
41.3
2-212
2-212
2-216
2-216
38.1 (11/2")
1140
50.8 (2")
2020
1.0
2.0
5.0
63.5 (21/2")
3170
1.6
3.2
7.9 22.2 31.7 66.6
0.0317
82.6 (31/4")
5360
2.7
5.4 13.4 37.5 53.5 113
0.0535
4.0
0.0811
96.8
149.2
136.5
38.1
47.6
2-223
203.2
(8")
All
100.0
168.3
155.6
38.1
47.6
2-223
254.0
(10")
304.8
(12")
1
2
1
2
120.7
127.0
136.5
142.9
215.9
257.2
215.9
257.2
50.8
63.5
60.3
73.0
0.0202
101.6 (4")
8110
8.1 20.3 56.8 81.1
170
127.0 (5")
12670
6.4 12.7 31.6 88.5 126
266
0.1267
152.4 (6")
18240
9.1 18.3 45.5 127
182
383
0.1827
177.8 (7")
24830
12.4 24.9 62.2 174
248
523
0.2486
203.2 (8")
32430
16.2 32.5 81.1 227
324
682
0.3246
254.0 (10")
50670
25.4 50.6 127 354 506 1065
0.5073
304.8 (12")
72970
36.5 73.0 182 510
0.7294
Piston
Rod
Ø
2-220
All
14.1 20.2 42.5
Litres
0.0114
730 1532
Deduction for Pull Force
2-216
177.8
(7")
Displacement
per 10mm
stroke
5
10 25 70 100 210
bar bar bar bar bar bar
0.6 1.1 2.9 8.0 11.4 24.0
mm2
73.0
Cylinder Push Force in kN
15.9 (5/8")
010404-0224
010404-0256
All dimensions are in millimetres unless otherwise stated.
31
Piston
Rod
Area
mm2
200
Piston Rod Force in kN
5
10 25 70
bar bar bar bar
0.1 0.2 0.5 1.4
100
bar
2.0
210
bar
4.2
Displacement
per 10mm
stroke
Litres
0.0020
25.4 (1")
500
0.3
0.5
1.3
3.5
5.0
10.5
0.0050
34.9 (13/8")
960
0.5
1.0
2.4
6.8
9.6
20.2
0.0097
44.5 (13/4")
1560
0.8
1.6
3.9 10.9 15.6 32.8
0.0156
50.8 (2")
2020
1.0
2.0
5.0
0.0202
14.1 20.2 42.5
63.5 (21/2")
3170
1.6
3.2
7.9 22.2 31.7 66.6
0.0317
76.2 (3")
4560
2.3
4.6
11.4 32.0 45.6 95.8
0.0456
88.9 (31/2")
6210
3.1
6.2 15.5 43.4 62.0 130
0.0621
101.6 (4")
8110
4.0
8.1 20.3 56.8 81.1
171
0.0811
127.0 (5")
12670
6.4 12.7 31.6 88.7 127
266
0.1267
139.7 (51/2")
15330
7.7
322
0.1523
177.8 (7")
215.8 (81/2")
15.3 38.4 107
153
24830
12.4 24.9 62.2 174
249
523
0.2486
36610
18.3 36.6 91.5 257 366
769
0.3663
Parker Hannifin
Cylinder Division
Europe
Pressure Limitations
Tie Rod Cylinders
2H Series
Low Pressure Operation
Maximum Pressure Ratings
Catalogue HY07-1110/UK
At low operating pressures, a wide range of application factors
such as seal friction and mounting alignment begin to affect
cylinder performance. Low friction seals are available to
special order, to optimise performance at low pressures. For
information, please consult the factory.
4 : 1 Design Factor (yield)
Bore Ø
(with rod no. 1)
Maximum Pressure
The majority of Series 2H cylinders are suitable for pressures
up to 210 bar for heavy-duty service with hydraulic oil. The
4:1 design factor rating shown is conservative for continuous
severe applications. Safety factors at other pressures can be
calculated from this rating. Mounting styles, stroke, etc., should
be considered because of the limiting effect they may have on
these ratings.
Three main areas of cylinder design may be affected by fatigue
stress at lower pressures: the cylinder body (pressure envelope),
the cylinder mountings, and the piston rod. The maximum
pressures indicated in the tables are based on pure tensile and
compressive loadings, without the presence of any bending
stresses. Where it is impractical to avoid side loadings, eg: by
the use of pivot mountings, please consult the factory.
(psi)
(bar)
(psi)
38.1 (11/2")
145
2040
210
3000
50.8 (2")
165
2340
210
3000
63.5 (21/2")
135
1920
210
3000
82.6 (31/4")
150
2100
210
3000
101.6 (4")
145
1970
210
3000
127.0 (5")
135
1900
210
3000
152.4 (6")
150
2100
210
3000
177.8 (7")
130
1840
210
3000
203.2 (8")
145
1980
210
3000
254.0 (10")
155
2200
210
3000
304.8 (12")
170
2380
210
3000
Maximum Pressure for H and J Mountings
Style H Mounting 1
Pull applications (bar)
Bore Ø
Cylinder Body (Pressure Envelope)
In many applications, the pressure developed within a cylinder
may be greater than the working pressure, due to pressure
intensification across the piston and cushioning, eg: in meterout circuits. In most cases, this intensification does not affect
the cylinder mountings or piston rod threads in the form of
increased loading. This induced pressure should not exceed
320 bar. If in doubt, please consult the factory.
For pressure limitations of specific cylinders, please refer to the
European cylinder InPHorm selection program HY07-1260/Eur.
Heavy-duty Service
(bar)
1
2
Style J Mounting 2
Push applications (bar)
Rod Numbers
Rod Numbers
1
2
3
4
5
1
2
3
4
5
38.1 (11/2")
210
210
–
–
–
180
110
–
–
–
50.8 (2")
210
210
–
–
–
180
110
–
–
–
63.5 (21/2")
210
210
210
–
–
180
110
130
–
–
82.6 (31/4")
210
210
210
–
–
180
110
145
–
–
101.6 (4")
210
210
210
–
–
180
110
125
–
–
127.0 (5")
150
210
180
195
–
160
60
115
85
–
152.4 (6")
150
210
180
195
–
130
60
100
75
–
177.8 (7")
110
150
120
125
–
110
40
90
70
–
203.2 (8")
110
150
120
–
130
70
40
55
–
45
254.0 (10")
180
210
–
–
–
72
46
–
304.8 (12")
135
210
–
–
–
Not recommended
–
–
For pressures exceeding those shown use mounting HB or HH
For pressures exceeding those shown use mounting JB or JJ
All dimensions are in millimetres unless otherwise stated.
32
–
–
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Piston Rod Sizes and Stop Tubes
Piston Rod Size Selection
For cylinders in compression (push) applications, the piston
rod has to be of sufficient diameter to provide the necessary
column strength. This is of particular importance in long stroke
applications – see 'Long Strokes and Stop Tubes', page 34.
1. Determine the type of cylinder mounting style and rod end
connection to be used. From the Stroke Factor table below,
identify which factor corresponds to the application.
2. Using this stroke factor, determine the ‘basic length’ from
the equation:
Basic Length = Net Stroke x Stroke Factor
(The Piston Rod Selection Chart on page 34 is prepared
for standard rod extensions beyond the face of the gland
retainers. For rod extensions greater than standard, add the
increases to the net stroke to obtain the ‘basic length’.)
3. Calculate the load imposed for the compression application
by multiplying the full bore area of the cylinder by the system
pressure, or by referring to the Push and Pull Force charts on
page 31.
4. Using the Piston Rod Selection Chart on page 34, look along
the values of ‘basic length’ and force as found in 2 and 3
above, and note the point of intersection.
The correct piston rod diameter is read from the diagonally
curved line above the point of intersection.
For cylinders in tensile (pull) applications, the rod size is selected
by specifying standard cylinders with standard rod diameters
and using them at or below the rated pressure.
inPHorm
For accurate sizing, please refer to the European cylinder
inPHorm selection program HY07-1260/Eur.
Stroke Factor Selection
Stroke
Factor
Rod End Connection
Mounting
Style
Fixed and Rigidly Guided
TB, TD, J, JB,
JJ, C, F, G
0.5
Pivoted and Rigidly Guided
TB, TD, J, JB,
JJ, C, F, G
0.7
Fixed and Rigidly Guided
TC, H, HB, HH
1.0
Pivoted and Rigidly Guided
D
1.0
Pivoted and Rigidly Guided
TC, H, HB,
HH, DD
1.5
Supported but not Rigidly
Guided
TB, TD, J, JB,
JJ, C, F, G
2.0
Pivoted and Rigidly Guided
BB, DB, SB
2.0
Supported but not Rigidly
Guided
TC, H, HB, HH
4.0
Supported but not Rigidly
Guided
BB, DB, SB
4.0
Type of Mounting
33
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Stroke Factors
Piston Rod Selection Chart
Recommended Length of
Stop Tube (mm)
Basic Length (mm) - Log Scale
Rod Diameter (mm)
Force (kN) - Log Scale
Consult Factory
Long Strokes and Stop Tubes
For long stroke cylinders under compressive (push) loads, a
stop tube should be used to reduce bearing stress. The required
length of stop tube is read from the vertical columns on the right
of the chart by following the horizontal band within which the
point of intersection lies. Note that stop tube requirements differ
for fixed and pivot mounted cylinders.
When specifying a cylinder with a stop tube, please insert an S
(Special) and the net stroke of the cylinder in the order code and
state the length of the stop tube. Note that net stroke is equal to
the gross stroke of the cylinder less the length of the stop tube.
The gross stroke determines the envelope dimensions of the
cylinder.
Cushion Sleeve
If the required length of stop tube is in the region labelled
'consult factory', please submit the following information:
Stop Tube
1. Cylinder mounting style.
2. Rod end connection and method of guiding load.
3. Bore required, stroke, length of rod extension (dimension W
or WF - dimension V – see pages 3 and 40) if greater than
standard.
4. Mounting position of cylinder. (Note if at an angle or vertical,
and specify the direction of the piston rod.)
5. Operating pressure of cylinder, if limited to less than the
standard pressure for the cylinder selected.
34
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Ports
Standard Ports
Series 2H cylinders are supplied as standard with BSPP ports
to ISO 228/1, spot faced for sealing washers. Metric threaded
ports to DIN 3852 Pt.1 and ISO 6149, or NPTF ports in sizes as
shown for BSPP ports, can be supplied if required.
Oversize Ports
For higher speed applications, oversize ports can be supplied in
all bore sizes, but are not available on Style JJ mounting (please
consult the factory). Ports one size larger than standard are the
maximum that can be accommodated in most heads or caps
within the standard envelope dimensions. Oversize or additional
ports can be supplied on the sides of heads and caps that
are not occupied by cushion valves. All oversize ports require
welded port bosses, which protrude from the side of the cylinder.
40
0.58
50.8 (2")
G1/2
M22x1.5
13
40
0.33
63.5 (21/2")
1
G /2
M22x1.5
13
40
0.21
G3/4
M27x2
15
53
0.17
0.11
0.07
152.4 (6")
G1
M33x2
19
85
0.08
177.8 (7")
G11/4
M42x2
24
136
0.09
203.2 (8")
G11/2
M48x2
30
212
0.11
254.0 (10")
G2
M60x2
38
340
0.11
304.8 (12")
G21/2
–
50
589
0.14
Rod
No
l/min.
Piston
flow at
Speed
5m/sec 1 in m/sec
82.6 (31/4")
2
101.6 (4")
All
127.0 (5")
All
152.4 (6")
All
G11/4
M42x2
24
177.8 (7")
All
G11/2
M48x2
30
212
0.14
203.2 (8")
All
G2
–
38
340
0.18
254.0 (10")
All
–
–
–
–
–
304.8 (12")
All
–
–
–
–
–
1
3
Tube
Bore
mm
63.5 (2 /2")
50.8 (2")
2
Port Size Port size
BSPP
Metric
1
2
1
2
1
38.1 (11/2")
1
Cap
13
Oversize Ports
Where large masses are involved, or piston speeds exceed
0.1m/s and the piston will make a full stroke, cushions are
recommended – see page 36.
Head
M22x1.5
127.0 (5")
The tables show piston speeds for standard and oversize ports
and connecting lines where the velocity of the fluid is 5m/s. Due
to piston rod displacement, the flow at the cap end port will be
greater than that at the head end, at the same piston speed. If
the desired piston speed results in a fluid flow in excess of 5m/s,
larger lines with two ports per cap should be considered. For
cylinders with oversize ports and with a fluid velocity exceeding
8m/s into the cap end, please consult the factory with details of
the application. Parker recommends that a flow rate of 12m/s in
connecting lines should not be exceeded.
Positions of Ports
and Cushion Screws
in Head and Cap
l/min.
Piston
flow at
Speed
1
5m/sec
in m/sec
G1/2
101.6 (4")
Port Size and Piston Speed
1
Tube
Bore
mm
38.1 (11/2")
Bore
Ø
The table below shows standard positions
for ports, and cushion adjusting screws
where fitted. Many mounting styles can
2
4
be assembled with ports located at 90°
or 180° from standard. In these cases,
3
cushion needle and check valves, where
fitted, are also repositioned since their relation with the port
position does not change. Air bleeds, see page 8, may be
fitted in unoccupied faces of the head or cap, depending on
mounting.
Port Size Port size
BSPP
Metric
82.6 (31/4")
Note that Y and P dimensions may vary slightly to accommodate
oversize ports – please contact the factory where these
dimensions are critical.
Ports, Air Bleeds and
Cushion Adjustment Location
Standard Ports
Bore
Ø
G3/4 2
G3/4 3
M27x2 3
15
53
0.78
G /4
G3/4 3
M27x2 3
15
53
0.44
3
G /4
M27x2
15
53
0.28
G1
M33x2
19
85
0.18
136
0.12
3
2
0.27
0.11
This refers to fluid velocity in connecting lines, not piston velocity
Supplied with welded port bosses at cap only
Supplied with welded port bosses at both head and cap
Manifold Ports
Manifold ports are available on all mounting styles to special
order. Side mounted cylinders (Style C) can be supplied with the
cylinder ports arranged for mounting and sealing to a manifold
surface – see page 31.
Flange Ports
Flange ports are available on most large bore 2H series
cylinders. Please consult the factory for details.
Mounting Styles
TB, TC, TD, J, JB,
H, HB, BB & SBa
JJ
HH
C
D
DB
1
3
Port
1
2
3
4
1
2
3
4
1
2
3
4
1
Cushion
2
3
4
1
3
3
1
1
3
3
1
1
2
Port
1
2
3
4
1
2
3
4
1
2
3
4
1
1
2
3
4
1
3
Cushion
2
3
4
1
3
4
1
2
3
3
1
1
2
3
4
1
2
3
1
3
1
DD
1
3
2
3
4
1
4
1
2
3
4
1
2
4
2
3
4
1
2
2
4
1
1
2
3
4
1
2
4
3
4
1
2
2
4
1
All dimensions are in millimetres unless otherwise stated.
35
G&F
Parker Hannifin
Cylinder Division
Europe
Cushioning
Tie Rod Cylinders
2H Series
An Introduction to Cushioning
Example
Catalogue HY07-1110/UK
The option of cushioning is recommended as a means of
controlling the deceleration of masses, or for applications where
piston speeds are in excess of 0.1m/s and the piston will make
a full stroke. Cushioning extends cylinder life and reduces
undesirable noise and hydraulic shock.
Cushions can be supplied at the head and/or cap ends of a
cylinder without affecting its envelope or mounting dimensions.
Standard Cushioning
Where specified, 2H cylinders use cushions which are profiled
to give efficient, progressive deceleration. Final speed may be
adjusted using the cushion screws.
Note that cushion performance will be affected by the use of
water or high water-based fluids. Please consult the factory for
details.
The following example shows how to calculate horizontal
deceleration (α=0).
Selected bore/rod 127/50.8mm (No. 1 rod)
Pressure = 35 bar
Mass = 2268kg
Velocity = 0.6m/s
Cushion length = 27mm
Friction coefficient = 0.15 or 3337N
F=
ma + Ad P/10
where a =
0.62
2 x 27 x 10-3
and =
6.66 m/s2
F = 2268 x 6.66 + 12670 x 35/10 - 3337 = 56128N
The total deceleration force is developed by the fluid
compressed in the cushion chamber. This pressure is
approximately equal to the force divided by the annular area
(cylinder bore area - rod area):
Alternative Forms of Cushioning
Special designs can be produced to suit applications where
the energy to be absorbed exceeds the standard cushion performance. Please consult the factory for further details.
56128N
12670mm2 - 2020mm2
Cushion Length
2H cylinders incorporate the longest cushion sleeve and spear
that can be accommodated within the standard envelope
without reducing the rod bearing and piston bearing lengths –
see table of cushion lengths below.
Cushion Calculations
Modelling the cushion performance on uniform deceleration, the
formulae below can be used to determine the approximate force
developed in the cushion chamber when decelerating a load.
Formulae
Cushion Length and Piston and Rod Mass
Bore
Ø
Rod
No.
38.1
(11/2")
1
2
MM
Rod
Diameter
15.9 (5/8")
25.4 (1")
50.8
(2")
1
2
1
2
3
1
2
3
1
2
3
1
2
3
4
1
2
3
4
1
2
3
4
1
2
3
5
1
2
1
2
25.4 (1")
34.9 (13/8")
25.4 (1")
44.5 (13/4")
34.9 (13/8")
34.9 (13/8")
50.8 (2")
44.5 (13/4")
44.5 (13/4")
63.5 (21/2")
50.8 (2")
50.8 (2")
88.9 (31/2")
63.5 (21/2")
76.2 (3")
63.5 (21/2")
101.6 (4")
76.2 (3")
88.9 (31/2")
76.2 (3")
127.0 (5")
88.9 (31/2")
101.6 (4")
88.9 (31/2")
139.7 (51/2")
101.6 (4")
127.0 (5")
127.0 (5")
177.8 (7")
139.7 (51/2")
215.9 (81/2")
82.6
(31/4")
F = ma + Ad P/10 - mgsinα - f
(for inclined or vertically upward direction of mass)
Where:
F = total force acting on the cushion chamber in Newtons
m = mass of load in kilogrammes (including piston, rod, and rod end accessories, see table and pages 27 to 29)
a = deceleration in m/s2, derived from the formula
a=
v2
2s x 10-3
where: v = piston velocity in m/s
s = cushion length in mm
Ad = piston area subjected to pressure, in mm2 (see page 31)
P = pump pressure in bar
g = acceleration due to gravity = 9.81m/s2
α = angle to the horizontal in degrees
f = friction forces in Newtons = mg x 0.15
= 5.3N/mm2 or 53 bar.
This induced pressure should not exceed 320 bar.
63.5
(21/2")
F = ma + Ad P/10 + mgsinα - f
(for inclined or vertically downward direction of mass)
101.6
(4")
127.0
(5")
152.4
(6")
177.8
(7")
203.2
(8")
254.0
(10")
304.8
(12")
Cushion Length
Head
Cap
28.6
30.2
28.6
28.6
28.6
28.6
34.9
27.0
34.9
34.9
27.0
27.0
33.3
31.8
27.0
28.6
33.3
38.1
46.0
42.9
46.0
33.3
52.4
49.2
33.3
42.9
49.2
50.8
54.0
50.8
54.0
50.8
Piston &
Rod only
Rod at Zero per 10mm
stroke kg Stroke kg
0.45
0.02
0.73
0.04
0.97
1.49
1.36
2.66
1.87
2.83
4.34
3.64
4.99
7.71
5.68
8.73
15.70
10.75
13.19
14.98
23.88
17.49
20.09
22.28
39.59
25.03
29.01
33.04
54.78
37.11
47.91
76.38
105.39
120.47
177.25
All dimensions are in millimetres unless otherwise stated.
36
Parker Hannifin
Cylinder Division
Europe
0.04
0.07
0.04
0.12
0.07
0.07
0.16
0.12
0.12
0.25
0.16
0.16
0.48
0.25
0.35
0.25
0.63
0.35
0.48
0.35
0.98
0.48
0.63
0.48
1.19
0.63
0.98
0.98
1.92
1.19
2.84
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Seals and Fluids
Fluid
Group
Seal Materials – a combination of:
Fluid Medium to ISO 6743/4-1982
Temperature Range
1
Nitrile (NBR), PTFE,
enhanced polyurethane (AU)
Mineral Oil HH, HL, HLP, HLP-D, HM, MIL-H-5606 oil,
air, nitrogen
-20°C to +80°C
2
Nitrile (NBR), PTFE
Water glycol (HFC)
-20°C to +60°C
5
Fluorocarbon elastomer (FPM),
PTFE
Fire resistant fluids based on phosphate esters (HFD-R)
Also suitable for hydraulic oil at high temperatures or in hot
environments. Not suitable for use with Skydrol.
See fluid manufacturer's recommendations.
-15°C to +150°C
6
7
Various compounds including nitrile,
polyamide, enhanced polyurethane,
fluorocarbon elastomers and PTFE
Water
Oil in water emulsion 95/5 (HFA)
+5°C to +50°C
Water in oil emulsion 60/40 (HFB)
+5°C to +50°C
Operating Medium
Low Friction Seals
Notes
Group 1 Seals are manufactured from an enhanced
polyurethane and do not require a gland seal back-up washer.
They should not be used if the working fluid is water glycol.
Group 6 Seals – System pressure should not exceed 70 bar
when using HFA fluids.
Water Service
The table above is a guide to the sealing compounds and
operating parameters of the materials used for rod gland, piston
and body seals. If there is doubt regarding seal compatibility
with the operating medium, please consult the factory.
For applications where very low friction and an absence of
stick-slip are important, the option of low friction seals is
available. In low pressure
applications, their use should
also be considered. If in doubt,
please consult the factory. The
gland seals comprise two low
friction PTFE stepped seals and
a conventional double lip wiper.
Modifications for use with water as the fluid medium include
a stainless steel piston rod with lipseal piston, and plating of
internal surfaces. When ordering, please specify the maximum
operating pressure or load/speed conditions, as the stainless
steel rod is of lower tensile strength than the standard material.
Temperature
Where operating conditions fall outside those specified in the
table, please contact the factory.
Green Fluids
Seals for use with specific ‘green fluids’ are available to special
order. Please consult the factory for details.
External Fluids
The environment in which a cylinder is used may cause fluids
such as cutting fluids, coolants, and wash down fluids, to come
into contact with the external surfaces of the cylinder. These
fluids may attack the seals, and must be taken into account
when selecting and specifying seal compounds.
Special Seal Designs and Materials
In addition to the standard and optional seals shown in the table,
special seals can also be supplied – please consult the factory
with details of the application. Please insert an S (Special) in the
order code and specify fluid medium when ordering.
37
Warranty
Parker Hannifin warrants cylinders modified for water or high
water content fluid service to be free of defects in materials or
workmanship, but cannot accept responsibility for premature
failure caused by excessive wear resulting from lack of lubricity,
or where failure is caused by corrosion, electrolysis or mineral
deposits within the cylinder.
Filtration
For maximum component life, the system should be protected
from contamination by effective filtration. Fluid cleanliness
should be in accordance with ISO 4406. The quality of filtration
should be in accordance with the appropriate ISO standards.
The rating of the filter medium depends on the system
components and the application. The minimum required for
hydraulic systems should be class 19/15 to ISO 4406, which
equates to 24µ(b10≥75) to ISO 4572.
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Replacement Parts and Service
Service Assemblies and Seal Kits
When ordering Service Assemblies and Seal Kits, please refer
to the identification plate on the cylinder body, and supply the
following information:
Serial Number - Bore - Stroke - Model Number - Fluid Type
Key to Part Numbers
1Head
7Cap
14 Gland/bearing cartridge
15 Cylinder body
17Piston
18 Cushion sleeve
19 Tie rod
23 Tie rod nut
26 Back-up washer – only on 177.8mm to 304.8mm (7” to 12”) bore cylinders
27Retainer
34 Piston rod – single rod, no cushion
611
69
69a
70
70a
71
72
73
74
119
120
121
1
2
Piston rod – double (weaker2) rod, cushion one end
O-ring – needle valve and check valve screws
O-ring – cartridge-type needle valve
Needle valve, cushion adjustment – bore sizes above 63.5mm (21/2”)
Needle valve assembly, cartridge type – bore sizes up to 63.5mm (21/2”)
Ball – cushion check valve – bore sizes above 101.6mm (4”)
Cushion check valve screw – bore sizes above 101.6mm (4”)
Floating cushion bush
Retaining ring for cushion bush
PTFE rings (Hi-Load piston)
Rubber pre-load rings (Hi-Load piston)
Wear rings (Hi-Load piston)
Not illustrated
See page 26 –
double rod strength
Gland
Cartridge
Wrench
Spanner
Wrench
15.9
69590
11676
25.4
69591
11676
34.9
69592
11703
44.5
69593
11677
50.8
69594
11677
63.5
69595
11677
76.2
69596
11677
88.9
69597
11677
101.6
69598
11677
127.0
69599
11678
139.7
69600
11678
177.8
–
–
215.9
–
–
Piston
Rod
Ø
121
48
35
36
37
40
41
42
43
44
45
47
48
55
571
581
601
Piston rod – single rod, cushion at head end
Piston rod – single rod, cushion at cap end
Piston rod – single rod, cushion at both ends
Wiperseal – for gland
Lipseal – for gland
Lipseal – for Lipseal piston
Back-up washer – for gland lipseal 41
(Groups 2, 5, 6 & 7 seals)
Back-up washer – for Lipseal piston
O-ring – gland/head
O-ring – cylinder body
Cast iron piston ring
Locking pin – piston/rod
Piston rod – double (stronger2) rod, no cushion
Piston rod – double (stronger2) rod, cushion one end
Piston rod – double (weaker2) rod, no cushion
40
Lipseal Piston
38
120
Hi-Load Piston
Cast Iron Piston
44
119
43
41
14
42
Gland Cartridge and Seals
Parker Hannifin
Cylinder Division
Europe
45
Replacement Parts and Service
Tie Rod Cylinders
2H Series
Piston and Gland Service Kits
Contents of Service Assembly Kits
Gland Service Cartridge Kit Contain items 14, 40, 41, 43,
45. Where the original gland incorporates a gland drain, please
consult the factory.
Head Assembly
Non-cushioned: 1, 26, 47
Cushioned:
1, 26, 47, 69, (69a), 70, (70a)
Cap Assembly
Non-cushioned: 7, 26, 47
Cushioned: 7, 26, 47, 69, (69a), 70, (70a), 73, 74
Catalogue HY07-1110/UK
(see key to part numbers opposite)
(see key to part numbers opposite)
Gland Service Kit Contain items 40, 41, 43, 45.
Piston
Rod
Ø
Gland Service
Cartridge Kit *
Standard Seals
Gland Service Kit *
Standard Seals
15.9 (5/8")
RG2HLTS061
RK2HLTS061
25.4 (1")
RG2HLTS101
RK2HLTS101
RK2HLTS131
34.9 (1 /8")
RG2HLTS131
44.5 (13/4")
RG2HLTS171
RK2HLTS171
50.8 (2")
RG2HLTS201
RK2HLTS201
3
63.5 (21/2")
RG2HLTS251
RK2HLTS251
76.2 (3")
RG2HLTS301
RK2HLTS301
88.9 (31/2")
RG2HLTS351
RK2HLTS351
101.6 (4")
RG2HLTS401
RK2HLTS401
127.0 (5")
RG2HLTS501
RK2HLTS501
139.7 (51/2")
RG2HLTS551
RK2HLTS551
127.0 (5") 1
RG902HTS501
RK902HTS501
139.7 (51/2") 2
RG922HTS551
RK922HTS551
177.8 (7") 1
RG902HLF701
RK902HLF701
RG922HLF851
RK922HLF851
215.8 (8 /2")
1
1
2
254.0mm (10”) bore size only
2
Cylinder Body
All types:
Cushion Screw/Cartridge Assembly
Screw type:
69, 70
Cartridge type: 69a, 70a
Check Valve Screw Assembly
Screw type:
69, 71, 72 (bore sizes above 101.6mm)
Piston Rod Assemblies
These kits contain a fully assembled piston and rod assembly
and are available with the following piston and rod types:
Piston Types
Cast Iron Ring:
Lipseal:
Hi-Load:
304.8 mm (12”) bore size only
Piston Service Kit, Cast Iron Rings Contains two each of items
26 (where fitted) and 47, plus four of item 48.
Piston Service Kit, Lipseal Piston Contains two each of items
26 (where fitted), 42, 44 and 47.
Piston Service Kit, Hi-Load Piston Contains two each of
items 26 (where fitted), 47, 119, 120 and 121.
Bore Ø
15
Piston Service Kit Piston Service Kit Piston Service Kit
Cast Iron Rings
* Lipseal Piston
* Hi-Load Piston
17, 48
17, 42, 44
17, 119, 120, 121
Rod Types
Single rod, non-cushioned:
Single rod, cushioned head:
Single rod, cushioned cap:
Single rod, cushioned both ends:
34
35, 18
36
37, 18
Double rod, non-cushioned:
Double rod, cushioned stronger end:
Double rod, cushioned weaker end:
Double rod, cushioned both ends:
57, 60,
58, 60, 18
58, 61, 18
58, 61, 18 x 2
38.1 (11/2")
PR152H001
PK152HLL01
PK152HK001
Tie Rod Torques
50.8 (2")
PR202H001
PK202HLL01
PK202HK001
Please refer to the table on page 30.
63.5 (21/2")
PR252H001
PK252HLL01
PK252HK001
82.6 (31/4")
PR322H001
PK322HLL01
PK322HK001
101.6 (4")
PR402H001
PK402HLL01
PK402HK001
127.0 (5")
PR502H001
PK502HLL01
PK502HK001
152.4 (6")
PR602H001
PK602HLL01
PK602HK001
177.8 (7")
PR702H001
PK702HLL01
PK702HK001
203.2 (8")
PR802H001
PK802HLL01
PK802HK001
254.0 (10")
PR902H001
PK902HLL01
PK902HK001
304.8 (12")
PR922H001
PK922HLL01
PK922HK001
Repairs
Although 2H cylinders are designed to make on-site
maintenance or repairs as easy as possible, some operations
can only be carried out in our factory. It is standard policy to fit a
cylinder returned to the factory for repair with those replacement
parts which are necessary to return it to ‘as good as new’
condition. Should the condition of the returned cylinder be such
that repair would be uneconomical, you will be notified.
* Seal Groups – Ordering
The kit numbers shown above are for Group 1 seals. For Group
2, 5, 6 or 7 gland seals, substitute ‘AHL’ for ‘HLTS’ where used,
and replace the '1' at the end of the number sequence with ‘2’,
‘5’, ‘6’ or ‘7’. For example, a Group 5 Gland Service Cartridge
Kit for a 50.8mm rod will be RG2AHL205. For Group 2, 5, 6 or 7
piston seals, substitute a ‘2’, ‘5’, ‘6’ or ‘7’ for the ‘1’ at the end of
the number sequence.
All dimensions are in millimetres unless otherwise stated.
39
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
Piston Rod End Data
254.0mm & 304.8mm (10" & 12") Bores Only
Rod End Details – All Except J, JB and JJ Mountings
Rod End Style 4
Rod End Style 8
A
Rod End Style 9
A
WF
WF
WF
V
B
NA
V
V
B NA CC
MM
KK
D
Wrench Flats
MM
B
NA
MM
KK
D
Wrench Flats
D
Wrench Flats
A
Rod End Details – J and JB Mountings
Rod End Style 8
Rod End Style 4
A
W
A
Rod End Style 9
W
W
V
B NA
KK
MM
B
NA
D
Wrench Flats
CC
MM
B NA
MM
KK
D
Wrench Flats
D
Wrench Flats
V
A
V
Rod End Styles 4 & 8
Rod End Details – JJ Mounting
Style 4 rod ends are recommended for all applications in
which the work piece is secured against the rod shoulder.
Where the work piece is not shouldered, Style 8 rod ends
are recommended.
If rod end style is not specified, Style 4 will be supplied.
Rod End Style 4
A
WF
Rod End Style 9
MM B1
RD B NA KK
For applications where a female thread is required.
D
Wrench Flats
Rod End Style 3
RT
RT1
Non-standard piston rod ends are designated ‘Style 3’.
A dimensional sketch or description should accompany the
order. Please specify dimensions KK or CC, and A.
Rod End Dimensions – 254.0mm & 304.2mm (10” & 12”) Bore Sizes Only
Style 4 & 9
Style 8
Bore Rod
Ø
No.
MM
Rod
Diameter
KK
Metric
KK
UNF
CC
Metric
CC
UNF
A
254.0
(10")
1
2
127.0 (5")
177.8 (7")
M90x2
M100x2
31/2 - 12
4 - 12
M110x2
M130x2
43/4 - 12
43/4 - 12
127
127
304.8
(12")
1
2
139.7 (51/2")
215.9 (81/2")
M100x2
M115x2
4 - 12
41/2 - 12
M130x2
M130x2
51/4 - 12
51/4 - 12
140
140
+0.00
-0.13
JJ Mount Only
D
NA
V
W
WF
146.0
196.8
110
150
123.8
174.6
7
13
32
38
158.7
234.9
120
180
136.5
212.7
7
13
32
38
B
B1
RD
max.
RT
RT1
74.9
81.0
–
214.3
241.3
273.1
25.4
28.6
–
41.7
82.0
87.2
–
260.3
206.4
336.6
33.3
28.6
–
46.1
All dimensions are in millimetres unless otherwise stated.
40
Parker Hannifin
Cylinder Division
Europe
Tie Rod Cylinders
2H Series
Catalogue HY07-1110/UK
How To Order
C
K
S
2H
Mounting
Style
Mounting
Modifications
Bore
Cushion
Head
Page 36
Double
Rod
Page 26
Special
Features
Ports
Piston
Type
Series
C
Piston
Rod
End
Cushion
Cap
Page 36
Rod
Thread
Piston
Rod
Number
Code
R
G
U
Y
Code Air Bleed
Position
eg:4 Head position 1-4
4 Cap position 1-4
00 No air bleeds
Piston Page
Cast iron rings (standard) 6
Hi-Load
6
Lipseal
6
Port Style
BSPP (ISO 228) – standard
Metric (ISO 3852 Pt.1)
NPTF (dry seal pipe thread
Metric (ISO 6149) JJ
2H
Code Rod End Style
Page
4 Style 4
3, 40
7 Style 7
3, 40
8 Style 8
3, 40
9 Style 9
3, 40
3 Style 3 (Special) – please supply description or drawing 3, 40
Mounting Style
Page
Extended Tie Rods 10, 11
Head Flanges
12, 13, 22
Cap Flanges
14, 15, 23
Side Lugs
16, 25
Side Tapped Holes
16
Side End Lugs
17
Cap Fixed Clevis
18, 25
Cap Fixed Eye with Spherical Bearing 18
Fixed Trunnions
20, 21, 24
R
K
1
4
M
1
4
M
Code
1
2
3
4
5
Rod Number
Rod No. 1
Rod No. 2
Rod No. 3
Rod No. 4
Rod No. 5
Page
3, 40
3, 40
3, 40
3, 40
3, 40
Accessories
Please state on order whether accessories are to be fitted
to the cylinder or supplied separately.
Key
All selections
125
Page
8, 35
8, 35
8, 35
CodeThread
Page
M Metric (standard) 3, 40
A UNF
Page
35
35
35
35
Double Rod Cylinders – Example
101.6 K
Port
Positions
Code Port Position
Page
eg: 1 Head position 1-4 35
1 Cap position 1-4 35
CodeModification
Page
P Thrust Key (Styles C, F, G only)
30
M Manifold Port O-ring (Style C only) 31
Code
TB, TC, TD
J, JJ, JB
H
, HH, HB
C
F
G
BB
SBa
D, DB, DD
Net
Stroke
(mm)
Air
Bleeds
Code Fluid
Page Medium
M Group 1 37
C Group 2 37
D Group 5 37
A1 Group 6 37
B Group 7 37
Code Special Features
Page
S Flange Ports
35
S Oversize Ports
35
S Special Seals
37
S Stop Tube
34
S Stroke Limiter
8
8
S Rod End Bellows
8
S Gland Drain Port
30
S Tie Rod Supports
S Water Service Modifications 37
– or to customer specification
Code
C
K
L
Fluid
Medium
D
11 44
41
Indicate optional features or leave blank
Parker Hannifin
Cylinder Division
Europe
Parker Worldwide
Europe, Middle East, Africa
AE – United Arab Emirates,
Dubai
Tel: +971 4 8127100
parker.me@parker.com
AT – Austria, Wiener Neustadt
Tel: +43 (0)2622 23501-0
parker.austria@parker.com
AT – Eastern Europe, Wiener
Neustadt
Tel: +43 (0)2622 23501 900
parker.easteurope@parker.com
HU – Hungary, Budaoers
Tel: +36 23 885 470
parker.hungary@parker.com
IE – Ireland, Dublin
Tel: +353 (0)1 466 6370
parker.ireland@parker.com
IT – Italy, Corsico (MI)
Tel: +39 02 45 19 21
parker.italy@parker.com
KZ – Kazakhstan, Almaty
Tel: +7 7273 561 000
parker.easteurope@parker.com
AZ – Azerbaijan, Baku
Tel: +994 50 22 33 458
parker.azerbaijan@parker.com
NL – The Netherlands, Oldenzaal
Tel: +31 (0)541 585 000
parker.nl@parker.com
BE/LU – Belgium, Nivelles
Tel: +32 (0)67 280 900
parker.belgium@parker.com
NO – Norway, Asker
Tel: +47 66 75 34 00
parker.norway@parker.com
BG – Bulgaria, Sofia
Tel: +359 2 980 1344
parker.bulgaria@parker.com
PL – Poland, Warsaw
Tel: +48 (0)22 573 24 00
parker.poland@parker.com
BY – Belarus, Minsk
Tel: +375 17 209 9399
parker.belarus@parker.com
PT – Portugal, Leca da Palmeira
Tel: +351 22 999 7360
parker.portugal@parker.com
CH – Switzerland, Etoy
Tel: +41 (0)21 821 87 00
parker.switzerland@parker.com
RO – Romania, Bucharest
Tel: +40 21 252 1382
parker.romania@parker.com
CZ – Czech Republic, Klecany
Tel: +420 284 083 111
parker.czechrepublic@parker.com
RU – Russia, Moscow
Tel: +7 495 645-2156
parker.russia@parker.com
DE – Germany, Kaarst
Tel: +49 (0)2131 4016 0
parker.germany@parker.com
SE – Sweden, Spånga
Tel: +46 (0)8 59 79 50 00
parker.sweden@parker.com
DK – Denmark, Ballerup
Tel: +45 43 56 04 00
parker.denmark@parker.com
SK – Slovakia, Banská Bystrica
Tel: +421 484 162 252
parker.slovakia@parker.com
ES – Spain, Madrid
Tel: +34 902 330 001
parker.spain@parker.com
SL – Slovenia, Novo Mesto
Tel: +386 7 337 6650
parker.slovenia@parker.com
FI – Finland, Vantaa
Tel: +358 (0)20 753 2500
parker.finland@parker.com
TR – Turkey, Istanbul
Tel: +90 216 4997081
parker.turkey@parker.com
FR – France, Contamine s/Arve
Tel: +33 (0)4 50 25 80 25
parker.france@parker.com
UA – Ukraine, Kiev
Tel +380 44 494 2731
parker.ukraine@parker.com
GR – Greece, Athens
Tel: +30 210 933 6450
parker.greece@parker.com
UK – United Kingdom, Warwick
Tel: +44 (0)1926 317 878
parker.uk@parker.com
ZA – South Africa, Kempton Park
Tel: +27 (0)11 961 0700
parker.southafrica@parker.com
© 2014 Parker Hannifin Corporation. All rights reserved.
North America
CA – Canada, Milton, Ontario
Tel: +1 905 693 3000
US – USA, Cleveland
(industrial)
Tel: +1 216 896 3000
US – USA, Elk Grove Village
(mobile)
Tel: +1 847 258 6200
Asia Pacific
AU – Australia, Castle Hill
Tel: +61 (0)2-9634 7777
CN – China, Shanghai
Tel: +86 21 2899 5000
HK – Hong Kong
Tel: +852 2428 8008
ID – Indonesia, Tangerang
Tel: +62 21 7588 1906
IN – India, Mumbai
Tel: +91 22 6513 7081-85
JP – Japan, Fujisawa
Tel: +81 (0)4 6635 3050
KR – South Korea, Seoul
Tel: +82 2 559 0400
MY – Malaysia, Shah Alam
Tel: +60 3 7849 0800
NZ – New Zealand, Mt Wellington
Tel: +64 9 574 1744
SG – Singapore
Tel: +65 6887 6300
TH – Thailand, Bangkok
Tel: +662 717 8140
TW – Taiwan, New Taipei City
Tel: +886 2 2298 8987
VN – Vietnam, Ho Chi Minh City
Tel: +84 8 3999 1600
South America
AR – Argentina, Buenos Aires
Tel: +54 3327 44 4129
BR – Brazil, Cachoeirinha RS
Tel: +55 51 3470 9144
CL – Chile, Santiago
Tel: +56 2 623 1216
MX – Mexico, Toluca
Tel: +52 72 2275 4200
Catalogue HY07-1110/UK POD 10/2014 ZZ
EMEA Product Information Centre
Free phone: 00 800 27 27 5374
(from AT, BE, CH, CZ, DE, DK, EE, ES, FI, FR, IE, IL,
IS, IT, LU, MT, NL, NO, PL, PT, RU, SE, SK, UK, ZA)
US Product Information Centre
Toll-free number: 1-800-27 27 537
www.parker.com
Your local authorized Parker distributor
Download PDF