Product Summary

Product Summary
ITI Part No. 60-807-95R, 60-807-43
,7,Š3HW,PPXQH6$:
3,50RWLRQ6HQVRU
Document Number: 466-1725 Rev. C
February 2001
Product Summary
8362G12A.DS4
❑
❑
A motion sensor (passive-infrared or PIR) detects movement within a specific area by sensing the infrared energy
emitted from a body as it moves across the sensor’s field of
view. When this motion is detected, the sensor transmits an
alarm signal to the control panel.
Use this motion sensor to protect locations where door/window sensors are impractical or not needed. For example,
use a motion sensor to protect large areas or open floor
plans. Motion sensors also provide backup protection for
door/window sensors.
❑
The ITI® Pet Immune SAW PIR utilizes advanced signal
processing, a new custom designed lens, and a new custom
designed sensing element. The combination of these
improvements provides false alarm immunity for pets with
a combined weight of up to 40 pounds (18 kg) while still
providing superior human catch performance.
❑
❑
❑
❑
This wireless motion sensor includes the following features:
❑
❑
❑
❑
❑
❑
35 feet by 40 feet (10.6 m by 12 m) coverage area
Three minute transmitter lockout time after an alarm
that helps extend battery life
Cover-activated tamper (optional wall-activated tamper
is included)
Supervisory signals transmitted every 64 minutes to the
control panel
Sensor low battery reports (trouble) to the control panel
Field-selectable sensitivity options (standard setting
required for pet applications)
1061G37A.DS4
˜ÃÌ>>̈œ˜Ê˜ÃÌÀÕV̈œ˜Ã
❑
❑
❑
Room temperature must be kept between 60º and
120° F (16º and 49º C).
If possible, locate sensors within 100 feet (30.5 m) of
the panel. While a transmitter may have a range of 500
feet (152 m) or more out in the open, the environment
at the installation site can have a significant effect on
transmitter range. Sometimes a change in sensor location can help overcome adverse wireless conditions.
Position the sensor to protect an area where an intruder
would be most likely to walk across the detection pattern (see Figure 1).
Mount the motion sensor on an insulated, outside wall
facing in.
Mount the motion sensor on a rigid surface which is
free from vibrations.
Position the sensor so it faces a solid reference point,
like a wall.
Do not aim the sensor at windows, fireplaces, air conditioners, area heaters, forced air heating vents, or place
it in direct sunlight.
Do not mount the sensor near duct work or other large
metallic surfaces which may affect the RF signals (see
“Final Testing” on page 4). Actual acceptable transmitter range should be verified for each installation.
Mount the sensor permanently on a flat wall or in a corner. Do not set it on a shelf.
Windows should be closed in any area which has an
armed motion sensor.
Installation Guidelines
This PIR was designed for indoor use in the presence of
pets having a combined weight of up to 40 pounds (18 kg).
The following installation guidelines must be met to provide this false alarm immunity.
❑
❑
❑
The sensor must be incline-mounted on a wall surface
or incline mounted in a corner at a mounting height of
7.5 feet (2.3 m). See Figure 4.
The sensitivity switch must be set to Standard.
The pet must not be allowed to climb on objects such as
furniture, boxes, etc. within the field of coverage. See
Figures 2 and 3 to determine the sensor’s field of coverage.
ITI® Pet Immune SAW PIR Motion Sensor
Person walking across detection path
8362G04B.DS4
Figure 1. Overhead (Bird’s Eye View) Detection Path
1
Mounting the Motion Sensor
To mount the sensor:
0m
20 ft
TOP VIEW
11 m
6m
10 ft
3m
0 ft
0m
1.
Remove the mounting plate by depressing the button
on the top of the sensor body. With the opposite hand
pull the mounting plate away from the body of the sensor.
2.
Punch out two of the bottom four mounting holes. See
Figure 4 for wall mount options. See Figure 5 to determine which knockouts to use when mounting the
motion sensor. Use the lower-side holes for corner
mounting, or the lower-middle holes for surface mounting.
3.
If you desire wall-tamper functionality, remove the
wall-tamper knockout (see Figure 5).
3m
20 ft
œÌi
The wall-tamper switch cannot be used when the sensor is corner mounted.
6m
35 ft
20 ft
0 ft
8362G11A.DS4
Figure 2. This graph shows the top view of the lens
coverage area, for the indoor motion sensor’s
lens.
0m
7.5 ft
U S E
W IT H
A N IM A L A L L E Y L E N S
11 ft
2.4 m
4 ft
1.2 m
WALL
TAMPER
KNOCKOUT
0m
35 ft
0 ft
0 ft
DO NOT
USE THESE
MOUNTING
HOLES
USE WITH
STANDARD LENS
Figure 3. Side View (Motion Sensor) at a mounting
height of 7.5 feet.
USE THESE
MOUNTING
HOLES
Mounting the Motion Sensor
8855G01A.DSF
Figure 5. PIR Mounting Plate Knockouts
This sensor must be incline-mounted on a wall surface or
incline mounted in a corner at a mounting height of 7.5 feet
(2.5 m) (see Figure 4).
CORNER MOUNT
4.
Mark the location of the required holes on the mounting surface.
5.
Use wall anchors and screws to secure into place.
Attach the sensor to the mounting plate.
6.
When testing is completed the PIR can be securely
attached to its mounting plate by screwing the smallest
enclosed screw into the hole at the top of the mounting
plate.
INCLINED MOUNT
Setting the Sensitivity on the Indoor
Motion Sensor
DO NOT FLUSH MOUNT
DO NOT MOUNT
USING SWIVEL MOUNT
For pet applications, the PIR must be set to standard sensitivity.
Figure 4. Wall Mount Options: Use the inclined position
for surface or corner mounting.
2
ITI® Pet Immune SAW PIR Motion Sensor
Testing
Programming
Refer to the panel installation instructions for information
on programming the sensor into the panel.
To trip the sensor:
1.
Remove the PIR from its mounting plate activating the
tamper switch.
2.
Exit the panel’s programming mode.
3.
Return the PIR to its mounting plate.
STANDARD
HIGH
8362G06A.DS4
Final Testing
Figure 6. Sensitivity Pins Locations
Testing
Final testing should be done to verify radio signal integrity
and confirm control panel programming and response. The
actual transmitter range can be determined by performing a
sensor test as follows:
Walk Testing
1.
After the sensor has been mounted, remove it from its
mounting plate and activate the tamper switch to start
the walk test mode.
Walk testing should be done to determine the sensor’s
actual coverage area. The edge of the coverage pattern is
determined by the first flash of the LED. This may change
slightly depending upon the sensitivity setting. Walk test
the unit from both directions to determine the pattern
boundaries.
2.
Replace the sensor in its mounting plate.
3.
Place the control panel in test mode. Move across the
detection pattern until the sensor’s LED turns on.
STOP your motion.
4.
Listen for the appropriate system response. If the system does not respond, proceed to “Troubleshooting” on
page 4.
1.
Remove the sensor body from the mounted mounting
plate, activate the tamper switch, and then remount the
body to activate the 60 second walk test mode.
2.
Walk across the coverage pattern to determine the coverage area, indicated by LED activation. Each activation extends the walk test mode for an additional 60
seconds.
After 60 seconds without motion the walk test mode and the
LED will no longer activate when motion is detected.
1/"
Excessive use of the walk test mode may reduce
battery life. Use only for initial setup and maintenance
testing.
œÌi
When the walk test mode has ended, an alarm can be
transmitted only after 3 minutes have passed since
the previous alarm. This 3 minute lockout time
reduces unnecessary RF transmissions in high traffic
areas thereby extending battery life.
Environment Testing
Turn on all heating or air conditioning sources which would
normally be active during the protection period. Stand
away from the sensor and outside the coverage pattern and
watch for alarms.
ITI® Pet Immune SAW PIR Motion Sensor
Maintenance
At least once a year, the range and coverage should be verified for proper operation. The end user should be instructed
to put the sensor in walk test mode and walk through the far
end of the coverage pattern to verify proper detection.
Replacing and Disposing of Batteries
The sensor is powered by 2 AA alkaline batteries. When the
system indicates the sensor has low batteries, replace the
batteries immediately.
When battery replacement is necessary, observe proper
polarity (as shown in the battery compartment) when
installing the new battery, or the sensor may be damaged.
Be sure to note that as you look at the battery compartment,
on the left side the positive battery end is down and on the
right side the positive end is up. When the battery is
replaced, wait at least 3 minutes after installing the battery
before activating the walk test mode.
CAUTION!
Replace only with 2 AA Alkaline batteries. Observe
polarity when installing new batteries. Installing the
batteries backward may cause damage to the sensor.
Dispose of used batteries according to the
manufacturer’s instructions and/or local government
authorities. See Figure 7 for battery locations.
3
Troubleshooting
Specifications
PIR
COVER
Power source:
2 AA alkaline batteries
Typical battery life:
2-4 years at 68° F ( 20° C)
Operating temperature range:
32° to 110° F (0° to 43° C)
Non-pet applications
PWB
COVER
LENS
60° to 110° F (16° to 43° C)
Pet applications
TABS
Storage temperature range:
-30° to 140° F (-34° to 60° C)
SENSOR
BODY
TAMPER
SWITCH
MOUNTING
PLATE
8362G02A.DS4
Humidity
95% RH
Dimensions:
L = 2.9” (7.3 cm)
W = 2.4” (6 cm)
H = 1.9” (5 cm)
Figure 7. PIR Components, Battery Locations, &
Tamper Switch
Notices
Troubleshooting
Approved for use in the countries marked with a check (9).
Use the following guidelines if the system does not respond
correctly when the sensor is activated.
❑
❑
Check programming and reprogram sensor into panel if
necessary.
Move the sensor to another location and test for correct
response.
To relocate a sensor:
1.
Test the sensor a few inches from the original position.
2.
Increase the distance from the original position and
retest until an acceptable location is found.
3.
Mount the sensor in the new location.
4.
If no location is acceptable, test the sensor as described
below:
❑ Test a known good sensor at the same location.
❑ If the system does not respond, avoid mounting a
sensor at that location.
❑ If the replacement sensor functions, return the
problem sensor for repair or replacement.
(9) Austria
() Liechtenstein
() Belgium
() Luxembourg
(9) Denmark
(9) Netherlands
() Finland
() Norway
(9) France
() Poland
(9) Germany
(9) Portugal
() Greece
(9) Spain
() Iceland
(9) Sweden
(9) Ireland
() Switzerland
(9) Italy
() United Kingdom
I T I | 2 2 6 6 S e co n d St r e e t No r t h | N o r t h S a i n t Pa u l M n | 5 5 1 0 9 | 8 0 0 - 7 77 - 2 6 2 4 | ww w. i n t e r l og i x in c . co m
© 2001 Int e rl ogix ,™ Inc. I nte r logix is a t ra dema rk of In te rl ogix , Inc. ITI, Adv ent , a nd S uper B us ar e re gist er e d tr ad emar k s of In t er lo gix , Inc .
Protected under US patents: 5,870,022; 4,855,713; 5,790,040
4
ITI® Pet Immune SAW PIR Motion Sensor
Notices
SECURITY ·LIFESAFETY · COMMUNICATIONS
MANUFACTURERS DECLARATION
OF CONFORMITY
For
Product identification
Product
Brand
Model/type
: Pet Immune SAW PIR Motion Sensor
: Interlogix
: 60-807-43-EUR
Manufacturer
: ITI
2266 2nd St. N.
N. St. Paul, MN 55109
USA
EU Representative
: Interlogix
Excelsiorlaan 28
B-1930 Zaventum
Belgium
Concerning
A sample of the product
has been tested by:
Standards used :
R&TTE
Mikes Product Service
Test report:
T14152-1-02SM
I-ETS 300 220 (10.1993)
KTL Arnhem
EN50130-4 (1995)
EN50130-4/A1 (1998)
EN60950, 1992 (A1, A2, A3, A4, A11)
IEC950, 2nd ed. 1991 (A1, A2, A3, A4)
98639220
98639250
Means of conformity
We declare under our sole responsibility that this product is in conformity with Directive 93/68/EEC (Marking) and
complies to the essential requirements of 1999/5/EC (R&TTE) based on test results using (non)-harmonized
standards in accordance with the Directives mentioned.
ITI® Pet Immune SAW PIR Motion Sensor
5
Notices
6
ITI® Pet Immune SAW PIR Motion Sensor
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement