Gold Medal Deluxe 1002S, Standard 1003S Sno-Konette Instruction Manual

Below you will find brief information for Sno-Konette Deluxe 1002S, Sno-Konette Standard 1003S. The Sno-Konette is a convenient and easy-to-use ice shaver that produces fluffy, delicious snow cones. It is perfect for use at home, in a restaurant, or at a special event. The Sno-Konette is also very easy to clean and maintain.

PDF Download

Document

Sno–Konette

Instruction Manual

Deluxe – Model #1002S

Standard – Model #1003S

Cincinnati, OH 45241-4807 USA

Part No 67933

SAFETY PRECAUTIONS

Sno-Konette

Installation Instructions

Inspection of Shipment:

Unpack all cartons and check thoroughly for any damage that may have occurred during transit. Damage claims should be filed immediately with the transportation company. Gold

Medal Products is not responsible for damage that occurs in transit.

Setup:

Your new Sno-Konette was assembled and tested at the factory.

Remove all packing material and tape before starting operation.

Electrical Requirements:

The following power supply must be provided:

120 Volt, 15 Amp, single phase, 60 cycle AC current

Your electrician must furnish sufficient power for proper machine operation. We recommend this machine be on a dedicated and protected circuit. Failure to wire properly will void the warranty and may result in damage to the machine.

It is Gold Medal Products Company’s recommendation that this machine be plugged directly into a wall outlet. The use of extension cords is not recommended due to safety concerns, and may cause sacrificed and/or reduced performance.

Before You Plug In Machine:

1. Make sure that the wall outlet can accept the three (3) prong grounded plug on the power supply cord.

2. The wall outlet must have the proper polarity. If in doubt, have a competent electrician inspect the outlet and correct if necessary.

3. DO NOT use a three (3) prong grounded to two (2) prong un-grounded adapter

3 All Models #1002S, #1003S

Sno-Konette

Operating Instructions

After unpacking the Sno-Konette you should locate the pusher handle (packed in a separate

box). Connect the pusher handle to the shaver body by using the bolt and nut provided. Plug

the power cord into the appropriate electrical outlet.

To Operate the Sno-Konette:

1. Fill the hopper to within an inch from the top with ice cubes or block ice (no larger than 3

to 4 inches). The larger the pieces, the better the snow.

2. Switch the motor on, and wait for it to reach full speed (this will take a minute or so).

3. Press the pusher handle down against the ice in the hopper. Apply firm and even

pressure to make the best snow. Practice will enable you to gauge when to stop.

This allows the ice to resettle against the shaver head. You may find that you

need to relieve the pressure two or three times during a cycle. Too much pressure will

result in snow that is coarse; too little pressure will make the snow mushy.

NOTE: Never allow any foreign or metallic objects around the shaver area of the Sno-

Konette. Ice picks, scoops, and debris that may be in the ice often damage blades.

Ice Requirements:

The Sno-Konette can take ice cubes or block ice, if you break the block into pieces

approximately 3 to 4 inches in size.

NOTE: The ice will not enter the shaving chute if the pieces are too large.

4 All Models #1002S, #1003S

MAINTENANCE INSTRUCTIONS

ORDERING SPARE PARTS

*

Always speak to a Gold Medal Products Technical Service Advisor before ordering any parts to help ensure accuracy for your product. Included diagrams may not be the latest information.

1. Identify the needed part by checking it against the photos, illustrations, and/or parts list.

2. When ordering, please include part number, part name, and quantity needed.

3. Please include your model number, serial number, and date of manufacture (located on the machine nameplate) with your order.

4. Address all parts orders to:

Parts Department

Gold Medal Products Co.

10700 Medallion Drive

Cincinnati, Ohio 45241-4807

Or, place orders by phone or online:

(800) 543-0862

(513) 769-7676

Fax: (513) 769-8500

E-mail:

[email protected]

Web Page:

www.gmpopcorn.com

Sno-Konette

Installing New Shaver Blades

Inspect your equipment before replacing the blades. Use a flashlight to examine the blades in

the shaver body. If the blades appear to be nicked or bent, then the blades should be replaced.

Follow this procedure:

1. Unplug the main power supply cord from the electrical outlet.

2. Remove the shaver head from the motor shaft by loosening the Allen head set screws (2)

between the motor and the hopper.

3. Remove the shaver head. Pull the shaver head off of the motor shaft and through the

hopper. If the shaver head is frozen onto the shaft, remove the hold down bolts on the motor.

Pull the motor back, trapping the shaver head against the inside of the hopper, until the

shaver head disengages.

4. After removing the shaver head, check the motor shaft for burrs and corrosion. Use a fine

tooth file to remove the burrs and corrosion.

5. Remove the blades from the shaver head. These blades may be sharpened, but it is far

better to replace the old blades with a new set.

6. Position the new blades and insert screws until they are finger tight.

7. Set the blade thickness equal to a dime. (See illustration below.) Make sure that the height is

even across the shaver head.

8. Tighten the blade screws completely. Check the blades again with a dime to ensure the

blades did not move while tightening the screws.

9. Replace the motor and shaver head. Mount the motor using the hold down bolts. Insert the

shaver head through the hopper and onto the motor shaft. Press the shaver head onto the

motor shaft with the pusher handle, then move the shaver head in another 1/8". Check that

the shaver head is not rubbing against the back of the hopper and the blades are not

touching the pusher handle.

10. Replace the set screws (2) between the hopper and the motor.

NOTE: Replace the shims that were between the motor base and the mounting surface.

SET TOP OF BLADE

FLUSH WITH HEIGHT

GAGE, AS SHOWN

HEIGHT GAGE

(USE A DIME)

SHAVER HEAD

SHAVER BLADE

BLADE MOUNTING SCREW

7 All Models #1002S, #1003S

Sno-Konette

Switch, Toggle SPST (1002S)

P/N 47201

Rocker Switch (1003S)

P/N 42798

Momentary Switch

P/N 38971

Pusher Handle Assy.

P/N 22068

Plastic Sno Pan

P/N 22072

Strain Relief

P/N 87810

Lead-in Power Cord

P/N 22038

Lamp Holder

P/N 49837

(1003S Only)

Motor, 115v

P/N 22012

8 All Models #1002S, #1003S

Sno-Konette

Set Screw 5/16-18 x 3/8 (x2)

P/N 74127

Shaver Head

P/N 22015

2 Hole Blade Set

P/N 22017

Drain Pan, Counter

P/N 12061

9 All Models #1002S, #1003S

Sno-Konette

PARTS LIST

Model # Model # Description

1002S 1003S

Part No.

12012 12012 Front Glass Strip

12013

12038

12039

47201

22034

1088

1206

39068

22228

22222

41020

41021

41022

41023

41057

47010

47155

49132

74119

75220

77747

12018

12013 Rear Glass Strip

12038 Front Glass (15" x 18")

12039 Side Glass (15" x 11 15/16")

42798 Rocker Switch Switch

22034 Ice Shaver Drain Hose (3' Long)

1088 6 oz Sno Dipper

1206 6 oz. Cup Dispenser with Bracket

39068 Ice Scoop

61115 Dome Assy (1002S) or Motor Cover Assy (1003S)

N/A Dome Sign (Glass) for 1002S

Light Tube Holder

Light Tube Holder Starter

Light Ballast

Light Starter

Light Tube

49837 Lamp Holder

87065 40 Watt Light Bulb

61112 Light Cover (Clear Plastic)

47010 Label, "Safe Operating Instructions"

47155 Rubber Feet (4 Req)

49132 Grip Nut (5/16-8; Motor Mounting; 4)

74119 Label, "Warning Disconnect Power"

75220 Hose Clamp with Screw

77747 Slot Head Hex Screw (#8-32 x 3/4") cabinet

12018 Blade Mounting Screw (8-32 x 3/8" Brass)

12480 Decal

10 All Models #1002S, #1003S

Sno-Konette

ELECTRICAL SCHEMATIC – MODEL #1002S

11 All Models #1002S, #1003S

Sno-Konette

ELECTRICAL SCHEMATIC – MODEL #1003S

12 All Models #1002S, #1003S

WARRANTY

WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original

Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.

THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED

OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR

PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY.

THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION

ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said

GOLD MEDAL equipment or any part thereof.

The term “Original Purchaser” as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL

PRODUCTS COMPANY, or their authorized distributor for the equipment.

THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL

PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT 1-800-

543-0862 TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE

EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS

CONCERNING THE REPAIR OR REPLACEMENT OF PARTS.

GOLD MEDAL PRODUCTS COMPANY

10700 Medallion Drive

Cincinnati, Ohio 45241-4807 USA www.gmpopcorn.com

Phone: 1-800-543-0862

Fax: 1-800-542-1496

© The text, descriptions, graphics and other material in this publication are the proprietary and exclusive property of Gold Medal Products Company and shall not be used, copied, reproduced, reprinted or published in any fashion, including website display, without its express written consent.

Hello! I am an AI chatbot specifically trained to assist you with the Gold Medal Standard 1003S Sno-Konette Instruction Manual. I have thoroughly reviewed the document and can help you locate the exact information you need or explain the content in clear and simple terms. Whether you’re looking for guidance on specific features, troubleshooting steps, or general usage, feel free to ask your questions. The more details you provide about your concerns or needs, the more accurately and effectively I can assist you!

Hide related prompts

Assistant typing

Assistant terminated

Key Features

Shaves ice into fluffy snow cones
Easy to operate and maintain
Durable construction
Includes a pusher handle, a shaver head, and a drain pan
Comes with a one-year warranty

Frequently Answers and Questions

How do I operate the Sno-Konette?

Fill the hopper to within an inch from the top with ice cubes or block ice (no larger than 3 to 4 inches), switch the motor on and wait for it to reach full speed (this will take a minute or so), and press the pusher handle down against the ice in the hopper.

What are the electrical requirements for the Sno-Konette?

The Sno-Konette requires a 120 Volt, 15 Amp, single phase, 60 cycle AC current. It is recommended that the machine be plugged directly into a wall outlet and avoid the use of extension cords.

How do I replace the shaver blades?

Unplug the main power supply cord from the electrical outlet, remove the shaver head from the motor shaft by loosening the Allen head set screws, remove the blades from the shaver head, position the new blades and insert screws until they are finger tight, set the blade thickness equal to a dime and tighten the screws completely, replace the motor and shaver head.

What is the warranty on the Sno-Konette?

The Sno-Konette comes with a six (6) month warranty covering labor and a two (2) year warranty covering parts. The warranty does not cover damage caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions.

What is the difference between the Deluxe and Standard models?

The Deluxe model has a dome sign, a light tube holder, light tube holder starter, light ballast, light starter, light tube, lamp holder, and a 40-watt light bulb. The Standard model does not have these features.