3X-C™ Magnifier User manual
3X-C™ Magnifier
User manual
1 PRESENTATION
The Aimpoint® 3X-C Magnifying module can be used in conjunction with all
Aimpoint sights for long-range aiming or observing. A variable (-2 to +2)
dioptric setting allows this magnifier to be adapted to the individual shooter’s
eye. The Aimpoint 3X-C can also be used as a handheld 3X monocular.
Aimpoint magnifiers utilize the red dot in Aimpoint sights as the aiming reticle,
eliminating the need for re-zeroing when shifting between non-magnified and
magnified aiming.
The Aimpoint 3X-C is encased in a shock absorbing protective rubber cover
that also creates an ideal ergonomic grip. Internal optical adjustments make
the aligning of the magnifier and sight quick and easy.
For quick attachment/detach, we recommend the use of the Aimpoint
FlipMount or the Aimpoint TwistMount.
1.1 Major components
1
3
2
Fig. 1Major components
1.Screws for centering
2.Diopter ring
3.Mounting surface
4.Rubber cover
4
1.2 Technical specifications
Optical system
Magnification
Exit pupil diameter
Field Of View (FOV)
Diopter adjustment range
Eye relief
Photopic, integral transmission
3X
6.5 mm
6°
± 2.0D
56 mm
75 %
Physical specification
Material housing
Dimensions (L × W × H):
Weight
Anodized black aluminum, black
rubber cover
103 mm × 45 mm × 45 mm
(4” × 1 ¾” × 1 ¾”)
220 g (7.8 ounces) including
rubber cover
Mechanical interface
The 3X-C is provided with a 30 mm diameter tube for mounting
Environmental specification
Temperature range
Humidity
Immersion
-25 °C to +40 °C
+40 °C, RH: 95 %
0.5 m (1.64 ft)
2 OPERATION
WARNING: Ensure the weapon is not loaded and the safety selector is in the
”safe” position before attempting to install, remove or perform maintenance
on the 3X-C - other than attaching/detaching it under normal use.
2.1 Installing the Aimpoint® 3X-C on a weapon
The mounting surface (3) of the 3X-C allow for mounting to any 30 mm
diameter ring mount. Follow the manufacturer’s instructions when installing
the 3X-C.
For quick attachment/detach, we recommend the Aimpoint FlipMount or the
Aimpoint TwistMount as shown in Fig. 2.
i
Aimpoint® FlipMount
Fig. 2Recommended mounts
i
Aimpoint® TwistMount
The height of the mount is correct when the optical axis of the 3X-C and
the Aimpoint sight coincide. Select a suitable position for the 3X-C on the
weapon base so the eye relief is correct and feels comfortable.
Assemble the 3X-C to the chosen mount and install it on the weapon. The
3X-C shall be mounted with the Aimpoint logo to the left.
Carefully tighten the mount to the weapon base and retighten after a few
rounds.
NOTE: Any adjustments (see “2.2 Centering”) of the 3X-C does not affect
the point of impact.
i
Aimpoint® Micro T-2
i
i
Aimpoint® FlipMount
Aimpoint® 3X-C
i
Optical axis
Fig. 3The optical axis of the 3X-C and the sight coincide
2.2 Centering
The 3X-C does not need to be zeroed. However, an Aimpoint sight used
together with the 3X-C must be zeroed so the red dot of the sight creates the
correct point of impact.
The 3X-C has two screws (1) that allow the user to center the red dot of the
Aimpoint sight when viewed through the 3X-C. Centering the dot inside the
3X-C is not necessary, but creates a more natural feel.
CAUTION: Do not continue to adjust the screws if you encounter resistance.
1
Fig. 5Centering
1.Screws for centering
2.3 Diopter setting
Additionally, on the 3X-C it is possible to adjust the diopter setting by rotating
the diopter ring (2) as shown in Fig. 4.
2
Fig. 4Diopter setting
2.Diopter ring
3 EXTREME CONDITIONS
Use in extreme heat or cold, salt air, sea spray, water, mud and snow, dust
and sand storms or high altitudes does not require any special procedures.
4 MAINTENANCE
To reach maximum protection level for all weather conditions, wax is added
into the rubber mixture. The wax is slowly migrating to the surface of the part.
The wax is used up completely during frequent use and is not noticed by the
user. For long time storage, the wax is not used up as frequently and is seen
as a grey film on the surface. Wipe with a damp cloth to restore to its original
condition.
CAUTION: Never clean the lenses with the fingers. Use a lens paper/cloth.
If no lens paper/cloth is available, simply blow away the dirt or fog up the
lenses and dry them with a clean and soft piece of cloth.
Aimpoint AB
Jägershillgatan 15
SE- 213 75 Malmö, Sweden
Phone +46 (0)40 671 50 20
Fax +46 (0)40 21 92 38
e-mail [email protected]
WWW.AIMPOINT.COM
© 2016 Aimpoint AB. [14607-1]
Aimpoint Inc.
14103 Mariah Court
Chantilly, VA 20151-2113, USA
Phone +1 703-263-9795
Fax +1 703-263-9463
e-mail [email protected]
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement