Epson | 8300NL - PowerLite XGA LCD Projector | User`s guide | Epson 8300NL - PowerLite XGA LCD Projector User`s guide

EPSON
Date:
TIB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
06/10/2009
Originator: DS
PSB.2009.06.002
Authorization:
TI 09-08j Rev. A
Total Pages: 8
PowerLite 735c / 737c / 745c /755c/ 765c / 835p /1705/1715/1815/1825/7850p
/ 8300 with EasyMP.net option, Pro G5150/G5350 / 1725 / 1735W / 85 / 825 /
826W
Release of EMP NS Connection for Windows & Mac Upgrade from v2.50 to
v2.51
This bulletin was created to inform you of the release of the new version 2.51 of the
EMP NS Connection software.
Description of Change:
Improvements have been made to the EMP NS Connection utility.
Reason:
The improvements to NS Connection V2.51 are as follows
Improvements(V2.50 ( V2.51
Improvements
„ Addition of 10 new languages: Arabic, Ukrainian, Romanian,
Indonesian, Croat, Slovak, Bulgarian, Malay, Vietnamese and Hebrew.
„
Addition of troubleshooting function (Windows Only)
When pressing the troubleshooting button, the
corresponding troubleshooting and error number is displayed
in the error message window.
• When experiencing problems with NS Connect, please report to
Epson the error number along with the failure information.
Error number
Page 1 of 8
PSB.2009.06.002
Also you can access troubleshooting by clicking Start Æ All programs Æ
EPSON ProjectorÆEMP NS ConnectionÆEMP NS Connection V2.51
Troubleshooting.
Page 2 of 8
PSB.2009.06.002
„
Fixed error message displayed by the NVIDIA utility
Failure Symptom
When starting Quick Wireless/USB Display/NS Connection on a PC with
the built-in NVIDIA graphics chip (ex.ThinkPadT61 NVIDIA Quadro NVS
140M/NVIDIA Quadro FX 570M Display Driver), the NVIDIA utility
displays consecutive error messages. As a result, some PCs will
experience a lock-up.
Countermeasure
Hardware acceleration level is set to 3 when Quick Wireless/USB
Display/NS Connection are being used.
Limitation
By setting hardware acceleration level to “3”, the mouse cursor flickers
more visibly than the setting of “None”. This symptom can be avoided by
unchecking the box for Transfer Layered Window on the Adjustment
performance tab in the Set Options window of NS Connection.
Note: When NS connection is being used, and the hardware acceleration
setting is changed manually, at next startup, NS connection starts with
the same setting level of hardware acceleration.
Page 3 of 8
PSB.2009.06.002
Limitation
All Operating Systems
• When using EAP type of security that consumes a lot of CPU resources,
projectors may disconnect from NS connection. The solution is to click
Set Options of NS Connection and set Adjust Performance to Fast.
• It takes more time for the PowerLite 1725 / 1735W / 1825 / Pro G5150 /
Pro G5350 projectors to disconnect from NS connection as compared to
the PowerLite 1705 / 1715 / 1815 projectors, due to the limitation of the
new OS (WindowsCE) on IM-X4 projectors.
• To avoid conflicts between the Quick Wireless and other makers’
utilities, when the Quick Wireless starts, this version stops services of
the other utilities listed in the attached file (Exhibit 1). When quitting
Quick Wireless, the other utilities resume their services.
• In the network environment using IEEE 802.11 b/g standards, the
wireless connection may drop under the following conditions. Due to
specification of wireless controllers, some wireless controllers don’t send
their beacon periodically. Even if a projector is connected to a PC via
wireless, if the projector doesn’t detect the beacon for 11b signal for a
certain period (30 – 60 seconds) from the PC , the projector judges that
there isn’t any PC using the11b signal in the network and switches to
communication with11g (default) signal. On the other hand the PC still
tries to communicate with 11b. As a result, the wireless connection
between the projector and the PC drops.
Solutions to this problem:
a. Establish a wireless communication between the PC and
projector via 802.11a signal.
Windows OS
• Due to a limitation of the module VLC for the Movie Sending mode
of the IM-X4 version projectors, when IM-X4 projectors display
MPEG2 and WMV images in Movie Sending mode via NSC V2.40,
fast-forward and rewind functions cannot be used. When IM-X3
projectors display MPEG2 via NSC V2.40, fast-forward and rewind
functions can be used.
Windows Vista OS
• Multi screen display function cannot be used
• Virtual display driver cannot be installed in PC.
• When UAC (User Account Controls) screen is being displayed, the
projected image pauses.
• The Motion picture of Windows photo gallery cannot be projected in fullscreen mode.
• Still images and motion pictures from Windows Media Center cannot be
projected in full-screen mode.
• Since NS Connection can capture Layered windows, the tool bar of NS
Connection is projected.
•
•
• When projecting images via NS Connection, mouse cursor might blink
depending on PC specification.
Page 4 of 8
PSB.2009.06.002
Macintosh OS
In case of uninstalling NSC V2.20 or later version, it is
possible to uninstall by following 2 methods.
- Delete by installer exclusively for NSC version which you
want to uninstall.
For example, when you want to uninstall NSC V2.40, you need
to use installer for NSC
V2.40. NSC V2.20 and later version can not be uninstalled
automatically by different
version installer.
- Delete manually.
System Requirements:
OS
CPU
Memory
Available hard disk
space
Display
Windows 2000 SP4/ XP Home Edition/ XP Professional(32bit)
/Vista SP1 Home Basic / Home / Premium / Ultimate / Business
/ Enterprise(32bit) Mac OS X 10.3 minimum, OS
10.3.9/10.4.5/10.5.1 recommended
Windows: Mobile Pentium III 1.2GHz at least (Pentium
M1.6GHz at least recommended)
Mac: Power PC G3 900MHz at least recommended
At least 256MB (At least 512MB recommended)
At least 20MB
Minimum- VGA(640×480), Maximum- UXGA (1600 x 1200)
16-bit color or more
Obtaining the Update:
Download epson13123.exe from www.epson.com to the version 2.50 update for NS
Connection.
The files are extracted and copied to C:\EPSON\epson13123_EMP_NS_Connection_251.
The user should be directed to this folder to find the bulletin. The program will automatically
install after the download file is extracted.
Note: on the Mac, the extraction process copies the epson13124_EMP_NS_Connection_251
folder to the desktop. The program and bulletin are inside this folder. The user will double-click
on NSCv2.51_Installer to start the installation process.
Software Upgrade History:
Version Release date
1.00
December 25,
2002
1.10
January 1, 2003
1.20
September 10,
Remarks
New release
Release for PowerLite 7850p
Improved the transfer rate specification for PowerPoint
Page 5 of 8
PSB.2009.06.002
1.30
1.31
1.32
1.40
2003
May 31, 2004
June 18, 2004
January 18, 2004
April 1, 2005
2.00
2006/06/20
2.10
2006/12/08
2.20
2006/05/29
2.30
Nov. 27, 2007
2.40
Mar. 24, 2008
2.50
Jun.2,2008
2.51
Feb.9,2009
images
Support added for WPA and LEAP
Improved screen problem issue
Improved the internal function of connecting to the projector
• Addition of Presentation Mode and Interruption
Prevention function
• Able to present with video set for 32 bit color
• Function improvement with Excel and PowerPoint
• Improved ESSID search lockup prevention when
certain LAN adapters and drivers are used
• Addition of multi screen display function
• Addition of movie sending mode
• - Improvement of connection and usability
• Improvement in the ability to search projectors by
Automatic Search. (For Windows)
• Improvement in the operability of choosing projector.
• Improvement in operability and visibility of “Connect”
button.
• Preventing Virtual Display from being used as primary
display.
• Improvement in the ability of image processing speed.
(For Mac)
• - Change the packet size for a connection request
command used by Quick connection.
EMP NS Connection V2.20 supports Windows Vista (Home
Basic
/Home Premium/Ultimate/Business/Enterprise).
• Supported picture transfer for EMP-1825
• Improved wireless search and connection abilities.
• - Added video format supporting movie sending mode
• EMP NS Connection V2.40 supports Windows Vista
Service Pack 1
• - Supports 24 languages
Supported image transfer and virtual display of 1280 x 768
• Changed the operation method to prevent NS
connection from being blocked by Windows Firewall
Added another wireless LAN utility that NS connection
supports
- Addition of supported models (PowerLite-85/825/826W)
- Addition of supported languages
- Addition of troubleshooting function (Only for Windows)
[Exhibit 1] Wireless LAN client list that NSC V2.30 and V2.40 stops their service
process
Page 6 of 8
PSB.2009.06.002
Supported by V2.30
Manufacturer
Adapter Name
Name
D-Link
Air Plus XTREMEG DWL-G650
NETGEAR
WN511T
BUFFALO
Buffalo all products
IBM
ThinkPad products
IBM
ThinkPad products
Logitec
NETGEAR
Logitec LAN-WAG/U2 Wireless
LAN Adapter
Wireless-G Notebook Adapter
v.5.0
WG511AJP
NETGEAR
WGM511
NETGEAR
WPNT511
Linksys
WPC300N
Linksys
WPC54G
Linksys
WPC54GX4
Linksys
WUSB54GP
Linksys
WUSBF54G
NETGEAR
WG511 v2
Linksys
Page 7 of 8
PSB.2009.06.002
Wireless LAN Utility
Name
D-Link AirPlus
XtremeG Utility (CD)
Smart Wireless Utility
Ver.1.1.5.9(CD)
Client Manager 3
Ver.1.2.10(Web)
Access
Connection(Web) *1
Ver.4 or later
Access
Connection(Web) *1
Ver.3.71
Logitec Wireless LAN
Client Utility
WPC54G-JP setting
utility
NETGEAR WG511A
Smart Wizard
Ver3.2.3.306
NETGEAR SMART
WIZARD -Wireless
Assistant WGM511 Ver
1.0.0.7
NETGEAR WPNT511
SMART WIZARD
Ver1.1.3.0
Wireless-N Notebook
Adapter Wireless
Network Monitor v1.05
Wireless-G Notebook
Adapter Wireless
Network Monitor Ver
3.1
Wireless-G Notebook
Adapter with SRX400
Setup Wizard V1.1
Wireless-G Portable
USB Adapter WLAN
Monitor v1.05
Wireless-G USB
Adapter with Wi-Fi
Finder
Linksys
WPC54GX
Supported by V2.40
Linksys
WUSB54GSC
Supported by Quick
Wireless
Connection V.1.00 /
NSC V2.50
Supported by Quick
Wireless Connection
v1.02 / NSCv2.51
Atheros
Wireless-G Notebook
Adapter With SRX
Wireless Network
Monitor v. 1.2
Compact Wireless-G
USB Adapter Wireless
Network Monitor v1.05
Atheros Client Utility
Broadcom
BCM4311 / BCM2050
Broadcom Wireless
Utility
NETGEAR
WN511B
NETGEAR WN511B
Smart Wizard Utility
NETGEAR
WG111v3
NETGEAR WG111v3
Smart Wizard Utility
NETGEAR
wn111
NETGEAR WN111
Smart Wizard Utility
NETGEAR
WUSB600N
Linksys Wireless
Network Monitor
PLANEX
GW-US300MiniW
PCI GW-US300MiniW
Utility
*1: Because Access Connection service stops, power display of Power Manager becomes
invalid.
Page 8 of 8
PSB.2009.06.002
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
04/20/2009
Originator: JAM
PSB.2009.06.001
Authorization:
TI 09-05e Rev. A/B
Total Pages: 5
PowerLite 735c / Cinema 500 / 737c / 745c / 755c / 765c / 830p / 835p /
1705c / 1715c / 6100i / 6110i / 7800p / 7850p / 7900NL / 8300i / 8300i with
EasyMP.net module / 9300NL / 1815p / 1825 / 822p / 83c / 822+ / 83+ /
G5000 / Pro G5150 / Pro G5350 / Pro G5200W / 1725 / 1735W / 400W /
410W / 84 / 85 / 825 / 826W
PowerLite 61p / 81p / 82c / 821p / 1810 / 260d (Latin America) / 280d (Latin
America) with TCP/IP to Serial converter
Release of EMP Monitor for Windows version 4.30
This bulletin was created to inform you of the release of the new version 4.30 of the Epson
EMP Monitor software utility.
Description of Change:
Improvements have been made to the EMP Monitor software utility.
Note: For the PowerLite 61p / 81p / 82c / 821p / 1810 / 260d (Latin America) / 280d (Latin
America) models, a serial to TCP/IP conversion adapter is necessary. The function of Auto
Update does not work for these models. You need to manually click on refresh to get an
updated status of projectors.
Reason:
The improved points of version 4.30 are as follows:
Application
Version
upgraded
Improved
points
EMP Monitor
Version 4.22 Æ Version 4.30
(1) Addition of 7 new languages
- Indonesian, Croat, Slovak, Bulgarian, Malay, Vietnamese, and
Hebrew
Existing 27 languages
- Chinese (Traditional), Netherlands, Danish, Polish, Hungarian,
Czech, Romanian, Slovene, Norwegian, Swedish, Finnish, Russian,
Ukrainian, Greek, Turkish, Arabic (Windows NT4 does not support),
English, Japanese, French, German, Italy, Spanish, Portuguese,
Chinese (Simplified), Korean, Catalan, Thai
Page 1 of 4
PSB.2009.06.001
(2) Addition of Input Source (Only PowerLite 84 / 85 / 825 / 826W)
Previous version of EMP Monitor included USB Display, USB and LAN as
one source: EasyMP.
The input source buttons for USB display, USB, and LAN are available as
separate input sources as shown below:
- Old version - EMP Monitor V4.22
EMP Monitor V4.22
- New version - EMP Monitor V4.30
EMP Monitor V4.30
.
(3) New feature for the PowerLite 84 / 85 / 825 / 826W.
Displays projector’s serial number in the Menu settings
-
The projector’s serial number is now displayed in the projector’s
menu under “info”,
EMP Monitor can also display the projector’s serial number as
shown below:
Page 2 of 4
PSB.2009.06.001
Limitations
When the PowerLite1725 / 1735W exhibit a Lamp Cover Open error state,
EMP Monitor cannot detect the error. The reason is that when the lamp
cover is opened, the primary power source that reports the error state to
EMP Monitor is turned off immediately. This is different from other models
which make the secondary power source turn off under the same condition.
Note: EMP Monitor Ver. 4.xx is not compatible with EMP Monitor Ver. 3.05 and earlier
versions. EMP Monitor Ver. 4.xx cannot read the setting files of EMP Monitor Ver. 3.05
and earlier versions.
System Requirements:
OS
CPU
Memory
Available hard disk
space
Display
•
Windows 98 SE / Me / NT 4.0 (SP6) *Except Arabic and
Hebrew / Windows 2000 Pro / XP Home Edition / XP
Professional (32 bit) / Vista Home Basic / Home Premium /
Ultimate / Business / Enterprise (32 bit) *Except Ukrainian /
Vista SP1 Home Basic / Home Premium / Ultimate /
Business / Enterprise (32 bit)
• Internet Explorer Ver. 5.0 or later must be installed
Minimum: Pentium MMX 166 MHz (Recommended: Pentium II
233 MHz or higher)
At least 64 MB (Recommended: 128 MB or above)
At least 50 MB
SVGA (800×600) or higher resolution, 32 bit or higher display
color
Obtaining the Update:
Download epson13055.exe from www.epson.com to get the version 4.30 update for EMP
Monitor. The files are extracted and copied to C:\EPSON\epson13055_emp_monitor_430.
This file is a self-extracting archive and will start the installation utility for EMP Monitor. Follow
the on-screen instructions during the installation process.
Page 3 of 4
PSB.2009.06.001
Software Upgrade History:
Version Release date
3.00
December
25,2002
3.01
February
26,2003
3.02
April
18,2003
3.03
November
21,2003
3.04
April
1, 2004
4.01
October
18, 2004
4.02
August
29, 2005
4.10
4.22
May
8, 2006
May
15, 2007
September
26, 2007
March 31, 2008
4.30
April 3, 2009
4.20
4.21
Remarks
Supported PowerLite 735c
Supported PowerLite 7800p / 8300i
Supported PowerLite 7850p / 8300i with EasyMP.net option
module
Supported PowerLite Cinema 500
Supported Serial -TCP/IP conversion adapter for PowerLite
61p / 81p
Supported projectors that are configured on a large-scale
network.
Addition of timer function and auto search function by
specifying IP addresses.
Improvement of communication logs size.
Addition of new functions, Improvement of usability, and
Corresponding to PowerLite 6100i.
EMP NS Connection V2.20 supports Windows Vista (Home
Basic / Home Premium / Ultimate / Business / Enterprise).
Supported 25 languages
Supported 27 languages
Addition of new Error Information
Supported Video (BNC)
Supported 34 languages
Additional Input Sources
Displays projector’s serial number in Menu settings
Page 4 of 4
PSB.2009.06.001
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
12/18/2008
Originator: DS
PSB.2009.01.006
Authorization:
TI 08-22e Rev. A/B
Total Pages: 7
PowerLite 735c / 737c / 745c / 755c / 765c / 835p
1705c / 1715c / 1815p / 1825p / 7850p / 8300i with EasyMP.net option
Pro G5150 / Pro G5350 / 1725 / 1735W
Release of Check Tool for Network Projectors V1.00 (for Windows)
This bulletin was created to inform you about the release of Epson Check Tool software
for Network Projectors version 1.00.
Description of Change:
First release of the Check Tool for Network Projectors for Windows
Reason:
The Check Tool for Network Projectors makes it possible to easily check whether
EPSON Quick Wireless Connection and EMP NS Connection’s Quick Connection mode
can operate on the users’ Windows PC properly. The Check Tool for Network Projector
can also be used as a reference check before the purchase of the projector or as a
troubleshooting Tool.
1) Function of the Application
Application
name
Check Tool for Network Projector V1.00
Notes
The Check Tool checks automatically whether EMP Quick
Wireless Connection and EMP NS Connection’s Quick
Connection mode can operate properly on the user’s Windows PC
in terms of the following four points:
1. Checks OS support.
• Checks whether the OS is supported by EMP Quick
Wireless Connection / EMP NS Connection.
2. Checks user account
• Checks user’s account for administrator privileges to
install EMP Quick Wireless Connection / EMP NS
Connection.
3. Checks the wireless LAN adapter
• Checks whether the wireless LAN adapter and
driver are installed on the PC.
• Checks whether the wireless LAN is active.
Page 1 of 7
PSB.2009.01.006
Notes
4. Checks wireless LAN switching
• Checks whether wireless LAN adapter is turned ON.
• Checks whether EMP Quick Wireless Connection
and EMP NS Connection’s Quick Connection mode
can set the SSID on the user’s PC when trying to
connect to a projector using EMP Quick Wireless
Connection and EMP NS Connection’s Quick
Connection Mode.
The Check Tool checks for communication conflict and whether it
can actually stop the utilities when both utilities--EMP Quick
Wireless Connection V1.00 and EMP NS Connection-- are both
installed on the users PC.
Page 2 of 7
PSB.2009.01.006
Notes
Output of the log file:
• The Check Tool records the result in a text file (log file).
Usually, the log file is saved under the name of
CheckInfoDATE.log in the directory where “EB_CHT.exe”
is stored
Limitations
•
When the Check Tool is checking the user’s PC, the user’s
PC drops off network.
•
The Check Tool does not check whether the firewall of
manufacturers of security software other than Windows
may be blocking EPSON Quick Wireless Connection/EMP
NS Connection.
2) Operating Environment
Check Tool for Network Projector V1.00
OS
CPU
Memory
Disk space
Display
Windows 2000 SP4 Rollup1
/ XP Home Edition/ XP Professional(32bit) non-SP,SP1,SP2,SP3
/Vista SP1 Home Basic/Home
Premium/Ultimate/Business/Enterprise(32bit)
non-SP,SP1
Windows: Mobile Pentium III 1.2GHz at least (Pentium M1.6GHz
at least recommended)
256MB at least (Recommendation: 512MB at least)
20MB at least
Resolution: At least VGA(640 x 480) but no more than UXGA
(1600 x 1200)
At least 16 bit color
Page 3 of 7
PSB.2009.01.006
3) Location of download file: Check Tool for Network Projector V1.00
Download epson12794.exe from the Epson website (www.epson.com).
This is a self-extracting file; please follow the screen prompts to install the
Check Tool software.
4) Double-click the [EB_CHT.exe] icon
5) Read the contents of the [SOFTWARE LICENSE AGREEMENT], and click the
[Agree] button.
6) A dialog indicating the program is starting opens with the following message:
This tool cuts off the network connection temporarily.
Click the [Start] button to begin verification.
Page 4 of 7
PSB.2009.01.006
7) The Check tool dialog is displayed. It takes a few minutes for the results
of the verification are displayed
8) When two or more wireless LAN adapters are available on your computer, the
adapter selection dialog opens.
Select the wireless LAN adapter and press the OK button to continue.
Page 5 of 7
PSB.2009.01.006
9) When the verification is complete, the result is displayed on the bottom of the
dialog.
The result is stored in the same folder as the check tool.
File Name: CheckInfo<****>.log
**** indicates the created date and time.
[Exhibit 1]
Wireless LAN client list that NSC and Quick Wireless Connection stop their
service process
Manufacturer
Name
D-Link
Supported by
NSC V2.30
NETGEAR
BUFFALO
Adapter Name
Air Plus
XTREMEG
DWL-G650
WN511T
NETGEAR
Buffalo all
products
ThinkPad
products
ThinkPad
products
Logitec LANWAG/U2
Wireless LAN
Adapter
Wireless-G
Notebook
Adapter v.5.0
WG511AJP
NETGEAR
WGM511
NETGEAR
WPNT511
IBM
IBM
Logitec
Linksys
Page 6 of 7
PSB.2009.01.006
Wireless LAN Utility Name
D-Link AirPlus XtremeG Utility
(CD)
Smart Wireless Utility
Ver.1.1.5.9(CD)
Client Manager 3
Ver.1.2.10(Web)
Access Connection(Web) *1
Ver.4 or later
Access Connection(Web) *1
Ver.3.71
Logitec Wireless LAN Client Utility
WPC54G-JP setting utility
NETGEAR WG511A Smart
Wizard Ver3.2.3.306
NETGEAR SMART WIZARD Wireless Assistant WGM511 Ver
1.0.0.7
NETGEAR WPNT511 SMART
WIZARD Ver1.1.3.0
Linksys
WPC300N
Linksys
WPC54G
Manufacturer
Name
Linksys
Adapter Name
Linksys
WUSB54GP
Linksys
WUSBF54G
NETGEAR
WG511 v2
Linksys
WPC54GX
Supported by Linksys
NSC V2.40
Supported by Atheros
NSC V2.50 &
Quick
Wireless
Connection
V1.00
WPC54GX4
WUSB54GSC
Wireless-N Notebook Adapter
Wireless Network Monitor v1.05
Wireless-G Notebook Adapter
Wireless Network Monitor Ver 3.1
Wireless LAN Utility Name
Wireless-G Notebook Adapter with
SRX400 Setup Wizard V1.1
Wireless-G Portable USB Adapter
WLAN Monitor v1.05
Wireless-G USB Adapter with WiFi Finder
Wireless-G Notebook Adapter
With SRX Wireless Network
Monitor v. 1.2
Compact Wireless-G USB Adapter
Wireless Network Monitor v1.05
Atheros Client Utility
*1: Because Access Connection service stops, power display of Power Manager becomes
invalid.
Software Upgrade History Quick Wireless
Version
Release date
Remark
V1.00
August. 12, 2008 V1.00 release
Page 7 of 7
PSB.2009.01.006
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
09/17/2008
Originator: VS
PSB.2009.01.003
Authorization:
TI 08-29e Rev. A
Total Pages: 8
PowerLite 1735W, 735c, 737c, 745c, 755c, 765c, 835p, 1705c, 1715c, 1725,
1815c, 1825, 7850p, 7950p, 8300i with EasyMP.Net optional module,
Pro G5150 and Pro G5350 projectors
EMP SlideMaker2 updated Version 1.30 – provides scenario support for
WXGA
(1280 x 800) resolution
This bulletin was created to inform users about a software update for the EMP SlideMaker2 to
Version 1.30.
Description of Change:
Updated software release for creating scenarios in WXGA (16:10) format.
Reason:
• The updated version of EMP SlideMaker2 provides support for creating scenarios in
XGA (1024 x 768) resolution and WXGA (1280 x 800) resolution.
• It also provides the ability to select scenarios in XGA (4:3) or WXGA (16:10) format,
depending on the projector model used for the presentation.
Limitations:
• When creating a 16:10 scenario, the JPEG image must be in a 16:10 format.
• A 16:10 converted scenario can only be displayed with a WXGA (1280 x 800) projector.
• A 4:3 converted scenario can be displayed with a XGA or WXGA supported projector.
• When adding a PowerPoint slide from a thumbnail window to EMP SlideMaker2 with
Microsoft Office 2007, the scenario image file may deteriorate due to an issue with
Microsoft Office 2007 SP1.
1 of 8
PSB.2009.01.003
1) Selecting Aspect Ratio for the Projector being used:
a) Properties Window
b) Drag and Drop Window
2 of 8
PSB.2009.01.003
2) How to Verify the Aspect Ratio of the Scenario:
The resolution of the scenario is displayed in the window title of the Scenario Window and
Scenario Preview as shown below:
a) Scenario Window
b) Scenario Preview
3 of 8
PSB.2009.01.003
3) Location of download file: EMP SlideMaker2 updated Version 1.30
Download epson12812.exe from the Epson website (www.epson.com)
This is a self extracting file, please follow screen prompts.
After “Clicking” on the “Setup.exe” file, your will be prompted to:
4 of 8
PSB.2009.01.003
Select you language.
5 of 8
PSB.2009.01.003
Click “Next” at this screen.
6 of 8
PSB.2009.01.003
Click “Finish” to complete the installation.
7 of 8
PSB.2009.01.003
4) How to User the software: Please refer to the original documentation that came with your
Projector.
5) Operating Environment:
OS
Office
CPU
Memory
Disk space
Display
Windows 98/98SE/Me/ 2000 Professional/XP Home Edition SP4
/ XP SP1,SP2,SP3 Professional(32bit)
/ Vista non-SP,SP1 Home Basic/Home Premium/Ultimate
/Business/Enterprise(32bit)
Office2000、OfficeXP、Office2003、Office2007
At least Celeron 300MHz (Recommended: Celeron 400MHz or
above)
At least 64MB(Recommended: 128MB or above)
At least 50MB
At least SVGA(800×600) (Recommended: XGA(1024x768))
8 of 8
PSB.2009.01.003
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
11/13/2007
PSB.2007.11.005A
TI 07-63e, Rev. A
Epson EMP Monitor
EMP Monitor Version 4.21 Release
Originator: AP
Authorization:
Total Pages: 3
This bulletin was created to inform you of the release of Epson EMP Monitor version 4.21
utility.
New Functions and Improvements:
New Functions,
Improvements
Support for 25
languages
Supported Models
All projectors (see Supported
Projectors table)
Abnormally low air
flow notification
PowerLite 6100i / 6110i
Air flow sensor error
PowerLite 6100i (with firmware
version 1.10 or later) / 6110i
Clean air filter
notification
PowerLite 6110i
Supported Projectors:
This application supports the following Epson projectors:
Page 1 of 3
PSB.2007.11.005A
Function / Improvement
Description
Language support extended to
include Chinese (traditional),
Dutch, Danish, Polish,
Hungarian, Czech, Romanian,
Slovene, Norwegian, Swedish,
Finnish, Russian, Ukrainian,
Greek, Turkish, Arabic.
Languages supported in prior
version of EMP Monitor: English,
Japanese, French, German,
Italian, Spanish, Portuguese,
Chinese (simplified), Korean
Indicates an abnormal decrease
in the force of air flow through
the air filter. User should check
for air filter obstructions, clean
and replace air filter as
necessary.
This feature is available only for
the indicated models.
Indicates air flow sensor error.
This feature is available only for
the indicated models
User notification to clean air filter.
This feature is available only for
the indicated model.
PowerLite 735c
PowerLite 737c
PowerLite 745c
PowerLite 755c
PowerLite 765c
PowerLite 830p
PowerLite 835p
PowerLite 1705c
PowerLite 1715c
PowerLite 6100i
PowerLite 7800p
PowerLite 7850p
PowerLite 7900NL
PowerLite 8300i / 8300NL
PowerLite 8300i with the
EasyMP.net Option Module
installed
PowerLite 9300NL
PowerLite 1815p
PowerLite 822p
PowerLite 6110i
PowerLite Cinema 500
PowerLite 61p
PowerLite 81p
PowerLite 82c
PowerLite 821p
Supported Operating Environment:
Operating System requirement
Minimum CPU requirement
Minimum RAM requirement
Drive space requirement
Display requirements
•
Windows 98SE / Me / NT 4.0 SP6 (except
Ukrainian) / 2000 Professional / XP Home Edition
/ XP Professional (32 bit) / Vista Home Basic /
Vista Home Premium / Vista Ultimate (32 bit) /
Vista Business (32 bit) / Vista Enterprise (32 bit)
(except Arabic)
• Internet Explorer 5.0 or later
Pentium MMX 166 MHz (Recommended: Pentium II 233
MHz or faster)
At least 64 MB (Recommended: 128 MB or more)
At least 50 MB free
SVGA (800 x 600) or higher resolution, 32 bit color
display or higher
Obtaining the Update:
Download epson12456.exe from www.epson.com to get the version 4.21 update for EMP
Monitor. This file is a self-extracting archive and will start the installation utility for EMP
Monitor.
Page 2 of 3
PSB.2007.11.005A
Software History:
Version
3.00
3.01
3.02
Release Date
December 25, 2002
February 26, 2003
April 18, 2003
3.03
3.04
November 21, 2003
April 1, 2004
4.01
October 18, 2004
4.02
August 29, 2005
4.10
May 8, 2006
4.20
4.21
May 29, 2007
September 26, 2007
Notes
Added support for the PowerLite 735c
Added support for the PowerLite 7800p / 8300i
Added support for the PowerLite 7850p / PowerLite 8300i
with the EasyMP.net option module installed
Added support for the PowerLite Cinema 500
Added support for the Serial ↔ TCP/IP conversion
adapter for the PowerLite 61p / 81p
Added support for projectors installed on large scale
networks
Addition of timer function, auto search by specifying IP
address.
Improvement of communication logs sizes
Addition of support for PowerLite 6100i with support for
additional monitoring features unique to the PowerLite
6100i
Added support for Windows Vista (32 bit)
Increased language support to 25 languages
Page 3 of 3
PSB.2007.11.005A
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
06/06/2005
Originator: JD
PSB.2005.06.001
Authorization:
N/A
Total Pages: 3
Powerlite 8300/8300 with EasyMP.net/9300 series Projectors
Filter-Cleaning Procedures
This bulletin was created to inform users about the filter-cleaning procedures necessary for
maintaining proper airflow and reducing the potential for overheating.
Reason:
The PowerLite 8300 and 9300 series projectors have five (5) filters that must be cleaned on a regular
basis. Cleaning the filters is critical to maintaining proper airflow inside the projector and reducing
possible overheating issues. Incomplete or infrequent filter-cleaning maintenance can cause one or
more filters to accumulate excessive dust over time. This can inhibit proper airflow so that the
projector begins to overheat during operation and eventually shut down. The next section provides
information on the location of the filters on the projector, cleaning instructions and recommended
maintenance schedules.
Action:
The following filters should be cleaned after every 100 hours of use. For dusty environments, filter
cleaning should be performed more frequently.
1) Wire mesh filter (inside lamp housing shutter):
Hold shutter open and use a computer vacuum to remove dust.
Page 1 of 3
PSB.2005.06.001
2) Air intake filters (2)--located at bottom of projector:
Use a computer vacuum to clean both filters. If you don’t have one, then use a soft brush and gently
clean the filters. If the dirt is difficult to remove or either filter is damaged or broken, replace the
filter(s).
Note: Both filters should be replaced when the lamp is replaced.
3) Power supply intake filter (located on side of projector—opposite handle side)
Use a computer vacuum to clean dust from the filter and vents.
Page 2 of 3
PSB.2005.06.001
4) Lamp intake filter (circular filter located at bottom of projector)
Use a computer vacuum to clean dust from the filter and vents.
Page 3 of 3
PSB.2005.06.001
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
05/11/2005
PSB.2005.05.005
N/A
PowerLite 8300i
1400 x 1050 DVI Compatibility Support
Originator: JAM
Authorization:
Total Pages: 2
Reason:
This bulletin is to inform you of the testing results for 1400 x 1050 DVI full-screen resolution
with the Epson PowerLite 8300i Projector.
Question:
1. Has the Epson PowerLite 8300 projector been tested for 1400 x 1050 DVI
full-screen display compatibility?
2. What type of DVI port is on the PowerLite 8300 and PowerLite 9300 Projectors?
Answer:
1. The Projector has native resolution of 1280 x 1024. Its maximum “DVI” resolution is 1280 x
1024. This Projector can only support 1400 x 1050 DVI full-screen display using a DVI-D
to VGA 15HD cable. Detailed information listed below.
2. The port on the rear A/V module is DVI-D (DVI Digital) dual link. It is not an analog port
and does not have the 4 extra analog pins for DVI-I (DVI Digital and Analog). A DVI-I cable
cannot physically attach to the port since it can cause damage to the cable.
Operating Systems tested:
System Version(s): Mac OS X 10.2.8
Hardware tested:
Computer(s):
Apple PowerMac G5
Video Chip Set:
NVidia, GeForce FX 5200
Video Test Generators tested:
Make:
Extron
Model #:
VTG 400
Page 1 of 2
PSB.2005.05.005
Projector Resolution “About” information:
Source:
DVI
Input Signal:
Digital-RGB
Resolution
1280 x 1024
Refresh Rate:
60 Hz
Input Device:
PowerMac G5
Source:
Input Signal:
Resolution
Refresh Rate:
Computer 1
Analog-RGB
1400 x 1050
60 Hz
Input Device:
Extron VTG 400
Tested by:
J.A.Madrigal
Epson America Inc.,
Advanced Product Support
Long Beach, CA
Page 2 of 2
PSB.2005.05.005
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
05/11/2005
PSB.2005.05.003
N/A
PowerLite 8300i and PowerLite 9300i
1400 x 1050 Compatibility Support
Originator: JAM
Authorization:
Total Pages: 2
Reason:
This bulletin is to inform you of the testing results for 1400 x 1050 full-screen resolution with
the Epson PowerLite 8300i and PowerLite 9300i video projectors.
Question:
1. Have the Epson PowerLite 8300 and PowerLite 9300 Projectors been tested for
1400 x 1050 full-screen display compatibility?
2. Why do some laptops undersize the screen and perform in a pan-and-scan function on
projectors with 1400 x 1050 native resolutions?
Answer:
1. Yes, the Projectors have been confirmed functional with various video sources and
software operating systems for full-screen display performance. Detailed information
listed below.
2. Various laptop manufacturers use ATI RagePro or ATI Radeon chipsets for the built-in
LCD screen. The “Advanced Settings” of the video driver function in pan-and-scan
mode when re-directing video to the external video port. The true output at the VGA
15-HD port is only 1280 x 1024 as verified using by a VGA monitor that can sense and
display the video settings from the monitor’s menu options.
Operating Systems tested:
System Version(s): Windows 98SE and Windows XP Service Pack 2
Mac OS X 10.2.8
Hardware tested:
Mother Board(s): ASUS P4BGL-VM ATX Motherboard
Video Chip Set:
Intel 8284G/GL Graphics Controller
Computer(s):
Video Chip Set:
Apple PowerMac G5
NVidia, GeForce FX 5200
Page 1 of 2
PSB.2005.05.003
Video Test Generators tested:
Make:
Extron
Model #:
VTG 400
Projector Resolution “About” information:
Source:
DVI
Input Signal:
Digital-RGB
Resolution
1400 x 1050
Refresh Rate:
60 Hz
Input Device:
PowerMac G5
Source:
Input Signal:
Resolution
Refresh Rate:
Computer 1
Analog-RGB
1400 x 1050
60 Hz
Input Device:
Extron VTG 400
Tested by:
J.A.Madrigal
Epson America Inc.,
Advanced Product Support
Long Beach, CA
Page 2 of 2
PSB.2005.05.003
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
10/08/2004
Originator: DS
PSB.2004.10.002
Authorization:
TI 04-46e Rev. A
Total Pages: 14
EMP NS Connection, EMP Network Manager, EMP Monitor,
EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver
Evaluation results of Epson Projector PC applications tested in Windows XP
with SP2.
The purpose of this bulletin is to provide information on Epson PC projector applications tested
under the Windows XP SP2 (Service Pack2) environment.
Description:
Information is provided about the evaluation results and recommendations for Epson PC
projector applications functionality in Windows XP SP2 Firewall environment.
Reason:
Compatibility testing for functionality of EMP NS Connection, EMP Network Manager, EMP
Monitor, EMP Multi Screen Adjustment, Cinema Color Editor, VCOM Driver in the Windows
XP SP2 environment.
Results of Windows XP SP2 installation:
Installing SP2 on PCs did not disturb the installation of the above software applications.
Also, the application software can be installed on PCs where SP2 or earlier versions are
installed without any issues.
The information contained in the following pages provides details for executing the
applications in Windows XP SP2.
Page 1 of 14
PSB.2004.10.002
Executing the Software:
When executing the software noted below for the first time after SP2 installation completes,
the following security alert messages are displayed:
[EMP NS Connection]
Security alert screen (EMP NS Connection)
[EMP Network Manager]
Security alert screen (EMP Network Manager)
Page 2 of 14
PSB.2004.10.002
[EMP Monitor]
Security alert screen (EMP Monitor)
[EMP Multi Screen Adjustment]
Security alert screen (EMP Multi Screen Adjustment)
The Security Alert screen for EMP Multi Screen Adjustment is shown after clicking the
Auto button of Network or clicking the Add button after entering an IP address in the
IP Address box.
Page 3 of 14
PSB.2004.10.002
[Cinema Color Editor]
Security alert screen (Cinema Color Editor)
The functions of the three buttons displayed in the security alert screen are explained
below.
[Keep Blocking] --- Enables you to register a started application in the “Exceptions”
program of the Windows Firewall. The network port that the
application uses is blocked. By selecting this button once, this
security alert message will not be shown when starting the
application next time.
[Unblock] ------------- Enables you to register a started application in the “Exceptions”
program of the Windows Firewall and unblock the network port that
the application uses. By selecting this option once, this security alert
message will not be shown when starting the application next time.
[Ask me later]-------- When you want to select both buttons above or select either one
later, this button is selected. The started application is not registered
in the “Exceptions” program of the Windows Firewall and the
network that the application uses is not unblocked. However, when
restarting the application, the same security alert message is shown.
•
PC applications will work normally on Windows XP with SP2 if the “Unblock
Item” is selected when the security alert screen is shown.
For the detail operation information of each application, please refer to the following:
Page 4 of 14
PSB.2004.10.002
Operating Status Report
When selecting the Keep Blocking button, the security alert message is closed and the
main screen of each application is displayed.
[EMP NS Connection Application]
Port 3620 is necessary for searching for projectors. If this port is blocked, projectors are not
detected.
The other applications operate normally. However, there is a case that execution of
automatic search disables automatic detection. This occurs when projectors are registered
for automatic detection in EMP Monitor before installing SP2, then the registered projectors
may not be detected again after SP2 installation. Therefore it is recommended to select
Unblock in the security alert screen.
If “Keep Blocking” has been selected when starting the application for the first
time, and the blocking needs to be removed, complete the execution of the application and
proceed with unblocking as follows:
a.) Start the Windows Security Center. Double click the icon in the shape of a shield that
is always displayed on the taskbar after the installation of SP2.
Windows Security Center screen
b.) Select and start Windows Firewall
Page 5 of 14
PSB.2004.10.002
[Caution]
In case the check box
for Don’t allow
exceptions
is checked (this box is
not checked at the
initial setting), a
network port for
software is not
unblocked even though
the software is checked
on Exceptions.
Make sure this option is
not selected.
Windows Firewall screen
Page 6 of 14
PSB.2004.10.002
c.) Select the Exceptions tab and display exceptions program.
[Caution]
If this check box is
not checked, the
security alert
screen is not
displayed when
starting software.
•Exceptions screen
d.) Check the check boxes for the software you don’t want to block.
Page 7 of 14
PSB.2004.10.002
[EMP NS Connection] • Check EasyMP Software box
Unblock screen (EMP NS Connection)
Page 8 of 14
PSB.2004.10.002
[EMP Network Manager Application]• Check EPSON Projector box
Unblock screen (EMP Network Manager)
Page 9 of 14
PSB.2004.10.002
[EMP Monitor Application]→ Check EasyMP.net Software box
Unblock screen (EMP Monitor)
Page 10 of 14
PSB.2004.10.002
[EMP Multi Screen Adjustment Application]→ Check EPSON Projector Software for
Multi Screen box
Unblock screen (EMP Multi Screen Adjustment)
Page 11 of 14
PSB.2004.10.002
[Cinema Color Editor Application] ---> Check Cinema Color Editor.
Unblock screen (Cinema Color Editor)
By following the above procedure, the network port that each application uses is unblocked
and they can operate normally.
Page 12 of 14
PSB.2004.10.002
Corresponding program name to PC applications
PC Application
Program name
EMP NS Connection
EasyMP Software
EMP Network Manager
EPSON Projector
EMP Monitor
EasyMP.net Software
EMP Multi Screen Adjustment
EPSON Projector Software for Multi Screen
Cinema Color Editor
Cinema Color Editor
When selecting the Unblock button:
The Security Alert screen is closed and the main screen is displayed. Then the search result
is displayed.
When selecting the Ask Me Later button:
Port 3620 which is used by EMP NS Connection and is necessary for discovering projectors
is blocked, and projectors are not detected.
The other applications operate normally. However, there is a case where execution of
automatic search disables automatic detection. This occurs when projectors are registered
for automatic detection in EMP Monitor before installing SP2, the registered projectors may
not be detected after SP2 installation.
Page 13 of 14
PSB.2004.10.002
VCOM Driver
The following message is shown after the VCOM driver is installed on your PC.
Select “No, not this time” item and continue the Plug&Play of the device.
8.) Notes:
When you add the program to Exceptions list, the program can receive network
communication from outside. This may cause a security risk such as exposure to a virus
attack.
Page 14 of 14
PSB.2004.10.002
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
04/19/2004
Originator: TC
PSB.2004.04.005
Authorization:
N/A
Total Pages: 1
PowerLite 735c/7850p & 8300i (with EasyMP.net module.)
EMP NS Connection failures caused by Remote Control applications
This bulletin was created to inform you of an issue that can occur when using the PowerLite
735c/7850p, 8300i (with EasyMP.net module) and remote control software.
Description of Issue:
The user attempts to run EMP NS Connection on Windows 98SE/Me/2000/XP with the PowerLite
735c/7850p/ 8300i (with EasyMP.net module). When the EMP NS Connection application is
launched, it immediately gives an error message stating that EMP NS Connection "FAILED TO
INITIALIZE."
Reason:
Epson has found that remote control software, like PCAnywhere and RealVNC, causes a conflict
with the EMP NS Connection application. These remote control applications use a "Video Hook
Driver" that conflicts with the Epson GDI Monitor driver that is installed and used by EMP NS
Connection. Most remote control programs load a small client application at Windows startup and
leave an icon in the system tray (located at the bottom right on the desktop) to indicate they have
been loaded. In most cases, the remote control software can be turned off by right-clicking on the
icon in the system tray and disabling or exiting the program. Remote control applications do not
have to be removed from the system in order for EMP NS Connection to run properly; they just
need to be turned off. Consult the documentation that came with the remote control software for
information on how to disable the software from automatically launching every time the computer is
started.
Once the remote control software has been turned off, EMP NS Connection should run without
returning an error. If you continue to have issues connecting to the projector, consult the EMP NS
Connection Help file or User's Guide for troubleshooting assistance.
Notes:
VNC stands for Virtual Network Computing. It is a remote console utility which allows a user at his
computer to assume control of another computer across a network, as if they were sitting in front of
that computer.
Remote Control Applications known to conflict with Epson EMP NS Connection
• PCAnywhere - versions 32, 9.0, 9.2, 10.0, 10.5 and 11.0 by Symantec
• Real VNC - versions 3.3.7 and 4.0 beta by RealVNC with the GNU Library General Public
License
• TightVNC - version 1.3dev3 based on VNC with the GNU Library General Public License
• NetworkStreaming – v. 7.1 (formerly ExpertVNC)
Any other VNC remote control software based on RealVNC under the GNU Library General Public
License or remote control programs that load a "Video Hook Driver" (listed in Windows Device
Manager under "Display Adapters), can cause similar conflicts.
Page 1 of 1
PSB.2004.04.005
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
02/26/2004
Originator: AP
PSB.2004.02.009
Authorization:
TI03-57e Rev. A
Total Pages: 1
PowerLite 735c / 7800p / 7850p / 8300i / Cinema 500
EMP Monitor version 3.03 Update
This bulletin was created to inform you of the availability of EMP Monitor version 3.03. This
version of the EMP Monitor software has added support for the PowerLite Cinema 500
projector. All other support for previously supported projectors remains the same.
This software update can be downloaded from the Epson website. Locate and download
epson11017.exe. This file is a self extracting archive that will automatically start the program
installer once the file is extracted to your computer hard drive.
Refer to the documentation provided with your projector for further information about the
operation of the EMP Monitor software.
Page 1 of 1
PSB.2004.02.009
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
October 17, 2003
Originator: VS
PSB.2003.11.001
Authorization:
TI 03-42e Rev. A
Total Pages: 3
PowerLite 735c / 7850p / 8300i with EasyMP.net option installed
Supported Wired and Wireless LAN cards
Reason:
This bulletin is to inform you of the testing results for wired and wireless LAN cards used with
the PowerLite 735c / 7850p / 8300i with EasyMP.net option installed.
Models and firmware versions used in the evaluation:
Model
PowerLite 735c
PowerLite 7850p
PowerLite 8300i with
EasyMP.net option
installed
PW firmware version
1.00
2.00
1.20
IM-X•IM-XP firmware version
1.01 (IM-X)
1.00 (IM-X)
1.01 (IM-XP)
Wireless LAN cards configuration:
1. The tested Wireless LAN cards are inserted into the PC and a wireless LAN connection
(Ad hoc mode) is made to the projector.
2. The tested Wireless LAN cards are inserted into the PC and a wireless LAN connection is
made to the projector using an access point (Infrastructure mode).
Items evaluated:
The following items were tested and confirmed to work in both Ad hoc and infrastructure
modes. (WEP is only supported in the infrastructure mode.)
1. All functions of EMP Monitor.
2. DHCP, ESSID and WEP can be setup by a browser and function properly.
3. EMP NS Connection functions properly with the freeze, mute, zoom, and video input
change features.
4. Power Point slide show works.
Operating systems used for testing:
Windows 98 and Windows XP
Page 1 of 3
PSB.2003.11.001
Evaluation results for the Wireless LAN cards:
Wireless LAN card
PowerLite 735c PowerLite
7850p
3Com,3crshpw 196, office connect
Cisco Aironet350 AIR-PCM341(2.4GHz)
FMV Notebook (Broadcom BCM4306)
FMV Notebook (Intersil Prism2.5)
Fujitsu FMV-JW181(Agere)
Fujitsu FMV-JW183(Agere HermesII)
Fujitsu FMV-W182(Intersil Prism2.5)
Fujitsu FMV-JW182(Intersil Prism2.5)
FMV-STYLISTICTB93(Intersil Prism2.5)
D-Link Airplus XtremeG DWL-G650
Intel,CR Pro Wireless 2011B, LAN PC
Card
Linksys WPC11 Wireless Network PC
Card
NetGear 54Mbps wireless PC Card
WG511
SMC 2435W, EZ Connect Turbo,
US Robotic Ref. 9514115MBP
BUFFALO WLI-CB-G54
ADTEK ADLINK2422C
FMV Notebook (Intel Calexico)
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
pass
-
PowerLite
8300i with
EasyMP.net
pass
pass
pass
pass
pass
pass
pass
pass
pass
-
pass
-
-
pass
-
-
pass
pass
pass
pass
Didn’t pass
Didn’t pass
Didn’t pass
Didn’t pass
Didn’t pass
Wired LAN cards configuration:
Insert the wired LAN card to be tested into the projector and make a network connection to the
PC.
Items evaluated:
The following items were tested and confirmed to work.
1. All functions of EMP Monitor.
2. DHCP can be setup using a browser and functions properly.
3. EMP NS Connection functions properly with the freeze, mute, zoom, and video input
change features.
4. Power Point slide show works.
Evaluation results for the Wired LAN cards:
Page 2 of 3
PSB.2003.11.001
Wired Card name
PowerLite 735c
3Com 3C589C-TP
3Com 3CXE589ET-JP
D-Link DFE670TXD
Fujitsu FMV-J182
Hawking PN652TX
Linksys PCM100 ver2
Netgear FA411
SMC SMC8041TX
3Com 10/100 LAN PC Card
3CCFE574BT
PCET100-CL
Linksys 10/100 PC Card
SMC 8041TX V.2, EZ PC Card
10/100, SMC
I-O Data PCLA/TE
PCC-TXD
Kingston EtheRx PC Card KNE-PC2T
pass
pass
pass
pass
pass
pass
pass
pass
pass
PowerLite
7850p
pass
pass
pass
pass
pass
pass
pass
pass
-
pass
pass
pass
-
Didn’t pass
Didn’t pass
Didn’t pass
pass
Didn’t pass
The following cards are NOT compatible:
1. 3Com 3CCFE575BT-JP
2. 3Com 3CXFE575CT-JP
3. 3Com 3CXFEM656C
4. Megahertz 10/100 LAN CardBus PC Card (3Com)
5. Come once (Taiwan card)
6. DFE-690TXD- Cardbus 32 bits
7. Fujitsu FMV-J184
8. Fujitsu FMV-J185
9. LPC3-CLTL
10. NetGear CardBus Notebook Adapter FA511
11. SMC 8036TX, EZ PC Card 10/100, SMC
12. TDK LAK-CB100X
13. Toshiba LANCB100A
14. Xircom CE3B-100BTX
15. Xircom CreditCard Ethernet CE3-10/10
NOTE:
No EMI (electro magnetic interference) was done, only a functionality evaluation.
Page 3 of 3
PSB.2003.11.001
EPSON
Date:
PSB #:
Reference:
Product(s):
Subject:
PRODUCT SUPPORT BULLETIN
07/16/2003
Originator: TC
PSB.2003.07.001
Authorization:
N/A
Total Pages: 1
PowerLite – 735c / 7850p / 8300i (with Easy-MP.Net option installed)
Epson Wireless Projectors and using dual mode 802.11b/g or 802.11b/a
wireless PC Cards
This bulletin was created to inform you of issues that have been reported when accessing Epson
Wireless Projectors using dual mode 802.11b/g or 802.11b/a wireless PC Cards, either in ad-hoc
mode or through dual mode Access Points.
Reason:
The dual mode PC Cards and Access Points tend to have interference and compatibility
problems when operating in dual mode.
Solution:
For optimal performance results with Epson 802.11b wireless products, it is recommended that
single/native 802.11b mode be used.
If your dual mode wireless PC Card and/or Access Point can be configured to support the
802.11”b” mode only, set it to 802.11”b” only.
Note: In some cases it is not enough to disable dual mode and set the mode to 802.11”b” only;
on some dual mode PC cards (802.11b/g or 802.11b/a) the "A" and “G” modes cannot be turned
off.
Page 1 of 1
Download PDF

advertising