Danuser Python Wire Unroller Operator Manual

PYTHON
WIRE UNROLLER
Read this entire manual. This
safety alert symbol is used
throughout this manual to call your
attention to messages involving your
personal safety and the safety of others.
Failure to follow these instructions can
result in injury or death.
WARNING
Si no entiende ingles, se prefiere que
busque a alguien que interprete las
instrucciones para usted.
Owner:
Date Purchased:
Manual #:
9MPYTHONWU2459065
Operator’s Manual
Danuser LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246 Fax: (573) 642-2240
E-mail: [email protected]
Website: www.danuser.com
Dear Owner/Operator,
Thank you for purchasing this Danuser Python Wire Unroller. We appreciate
your business.
The Python Wire Unroller is designed to meet the needs of farmers, ranchers,
and fencing professionals. The Python Wire Unroller connects to a 2” receiver
hitch and accepts most new spools of wire or wire spooled using the Python
Wire Winder.
Your safety as an operator of our product is very important to us. Therefore,
before you assemble, install, operate, maintain, remove, or move your Danuser
Python Wire Unroller, read and understand this manual thoroughly. If there is
anything you do not understand, immediately contact your dealer, or contact our
factory direct.
Phone:
Fax:
E-mail:
(573) 642-2246
(573) 642-2240
[email protected]
Your satisfaction in the performance and longevity of our product is also very
important to us and can be prolonged by proper assembly, installation, operation,
and maintenance as instructed in this manual.
Thank you again for your business and for your trust in our product. Please feel
free to contact us at any time for further assistance.
Sincerely,
Danuser LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel: (573) 642-2246
E-mail: [email protected]
Fax: (573) 642-2240
Website: www.danuser.com
Danuser provides this manual "as is" without warranty of any kind, either expressed or implied. Danuser assumes
no responsibility for errors or omissions. Danuser assumes no liability for damages resulting from the use of the
information contained herein. Danuser reserves the right to revise and improve its products as it sees fit. This manual
describes the state of this product at the time of its publication and may not reflect the product in the future.
Danuser is a registered trademark.
Foreword
Please read this manual thoroughly!
Before you assemble, install, operate, maintain, remove, or move
your Danuser Python Wire Unroller, read this manual thoroughly. If
there is anything you do not understand, immediately contact your
dealer, or call our factory direct at (573) 642-2246. Powered
equipment can be dangerous if not assembled, installed, operated,
maintained, removed, or moved properly.
Symbols
This SAFETY ALERT symbol identifies important safety
messages. Carefully read each safety message that follows.
Failure to understand and obey a safety message, or recognize a
safety hazard, could result in injury or death to you or others around
you. The operator is ultimately responsible for the safety of himself,
as well as others, in the operating area of the wire unroller.
Symbol
DANGER
Indicates an imminently
hazardous situation which, if not
avoided, will result in death or
serious injury.
WARNING
Indicates a potentially hazardous
situation which, if not avoided,
could result in death or serious
injury, including hazards that
are exposed when guards are
removed.
CAUTION
Indicates a potentially hazardous
situation which, if not avoided,
may result in minor or moderate
injury. It may also be used to
alert against unsafe practices.
NOTE
Table of
Contents
Meaning
This is important information
for proper use of this equipment.
Failure to comply may lead to
premature equipment failure.
Page
Letter to the Owner/Operator . . . . . . . . . . . . . . . . . . . . . . . . . 2
Foreword . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Decals & Safety Signs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Assembly & Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Removal & Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Python Wire Winder . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Form No. 3475
3
Safety
WARNING
Working with unfamiliar equipment can lead to careless injuries. Read and understand
this manual and the manual for your vehicle before assembling, installing, operating,
maintaining, removing, or moving this wire unroller. If there is anything in this
manual you do not understand, contact your dealer or Danuser LLC. The safe use of
this equipment is strictly up to you, the operator. If this wire unroller is used, loaned,
or rented by any other person, it is the owner's responsibility to make certain that the
operator prior to operating:
•
•
4
Reads and understands the Operator's Manuals
Is instructed in safe and proper use
•
This wire unroller is designed to be used in conjunction with a 2” receiver hitch
mounted to the rear of the vehicle.
•
It is the responsibility of the operator to see that no one is within twenty-five feet
(25') of the wire unroller or wire path before and during wire unroller rotation.
Do not operate the wire unroller with another person near or in contact with any
part of the wire unroller. Serious personal injury or death may result if any attempt is made to assist unrolling operations by hand.
•
All operators of this attachment must read and understand this entire manual,
paying particular attention to safety messages and operation instructions, prior to
assembling, installing, operating, maintaining, removing, or moving the wire
unroller.
•
Please remember it is also important that you read, understand, and follow the
safety signs on the attachment. Clean or replace all safety signs if they cannot
be clearly read and understood. They are there for your safety as well as the safety of others. Danuser LLC will furnish new wire unroller safety signs upon
request at no charge.
•
All things with moving parts are potentially hazardous. There is no substitute
for a cautious, safe-minded operator who recognizes potential hazards and follows reasonable safety practices.
•
Personal protection equipment including safety glasses, hearing protection,
safety shoes, and gloves are recommended during assembly, installation, operation, maintenance, removal, or movement of the wire unroller.
•
When the use of hand tools is required to perform any part of assembly, installation, maintenance, removal, or movement of the wire unroller, be sure the
tools used are designed and recommended by the tool manufacturer for that specific task.
•
Always use two people to handle heavy, unwieldy components during assembly,
installation, maintenance, removal, or movement of the wire unroller.
•
Never place any part of your body where it would be in danger if movement should occur during assembly, installation, operation, maintenance, removal, or
movement of the wire unroller.
•
Never exceed the rated trailer tongue weight of the vehicle hitch.
•
Never transport the wire unroller on highways while connected to vehicle hitch.
Safety
(continued)
•
Only properly trained people should operate this equipment. Do not allow anyone who has not read this entire manual and understood the safety rules, safety signs, and operation instructions to use this wire unroller.
•
Never allow children to operate or be around this wire unroller.
•
Do not allow riders on the equipment at any time. There is no safe place for any
riders.
•
Never use alcoholic beverages or drugs which can hinder alertness or coordination while operating this equipment. Consult your doctor about operating this equipment while taking prescription or over-the-counter medications.
•
Safe operation of equipment requires the operator's full attention. Avoid distractions such as radio headphones, cell phones, etc. while operating.
•
Before beginning operation, clear the work area of objects which might be picked up and thrown by or entangled in the wire and/or wire unroller.
•
Before you operate the attachment, check over all pins, bolts, and connections
to be sure all are securely in place. Replace any damaged or worn parts immediately.
•
Never replace the top plate assembly retaining pin with anything other than one
that meets the original equipment manufacturer’s standards and requirements.
A longer, or protruding, fastener is more likely to grab clothing or gloves, which
can result in serious injury or death.
•
Keep all helpers and bystanders twenty-five feet (25') away from the operating
attachment and the wire path.
•
Keep hands, feet, hair, jewelry, and clothing away from all moving and/or rotating parts.
•
Never place yourself between the vehicle and the attachment.
•
Never manually guide wire by hand or with tool.
•
Never exceed 10 MPH while unrolling wire.
•
Stay clear of wire path during tensioning. Wire may come loose or break, potentially injuring bystanders.
•
A heavy load can cause instability of the vehicle. Use extreme care during travel. Slow down on turns and watch out for bumps. Use all safety devices,
including a seat belt, as recommended in the vehicle operator’s manual.
•
Never attempt adjustments, service, or repairs while the attachment is in operation.
•
Store the wire unroller on a flat, level surface in an area where children do not
play. Securely block and support the wire unroller.
•
Do not modify the wire unroller. Modifications may weaken the integrity of the
wire unroller and may impair the safety, function, life, and performance of the
wire unroller.
5
Safety
•
When maintaining the wire unroller, use only parts that meet original equipment
manufacturer’s standards and requirements.
(continued)
•
Always use care when operating the wire unroller. Most accidents occur because of
neglect or carelessness.
Safety is a primary concern in the design, manufacture, sale, and use of the wire
unroller. Danuser confirms to you, our customer, our concern for safety.
DANGER
Improper operation of this wire unroller can cause serious personal
injury or death. Operation of this wire unroller should only be done
by a competent adult acting in compliance with the Operator's Manual.
Since unrolling operations are beyond our control, we disclaim all
liability for any damages, injuries, or death which may result.
WARNING
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
6
Decals &
Safety Signs
The Python Wire Unroller comes equipped with all safety signs in place. Their
locations are shown in this section. Read and follow their instructions and ensure
their care:
•
•
Keep safety signs clean and legible at all times.
Replace safety signs that are missing, illegible, or damaged.
To install new safety signs, follow these steps:
1.
2.
3.
4.
Clean the area where the safety sign is to be placed.
Spray a little soapy water on the surface where the safety sign is to be placed.
Peel the backing from the safety sign, and apply it in the position shown.
Firmly press the safety sign, and squeeze out the air bubbles with a straight edge (e.g., a credit card).
PART NO. 190000
Location: Spool Assembly, center column
PART NO. DIG53
Location: Frame, top
PART NO. DANUSER106
Locations: Frame, both sides
PART NO. 9875
Location: Frame, left side
PART NO. DIG54
Location: Frame, top
PART NO. CA65
Location: Frame, top
WARNING
Clean or replace all safety
signs if they cannot
be clearly read and
understood.
7
Specifications
B
Operator's Manual
Direction Terminology
Front
Right
Left
A
F
Rear
D
C
E
Python Wire Unroller
Spool Assembly Diameter (A)
22”
Frame Width (B)
2”
Overall Height (C)
30.75”
Spool Assembly Height (D)
16.75”
Overall Length (E)
47”
Minimum Wire Spool Inner Diameter (F)
1.25”
Weight
69 lbs.
Wire Capacity
Up to 3/4 mile barbed
Up to 6 miles smooth
Mounting Option
2” receiver hitch
8
Assembly &
Installation
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
CAUTION
Prepare the Vehicle
Read and understand the manual for your vehicle before installing or
using the Python Wire Unroller. This wire unroller is designed to be
used in conjunction with a 2” receiver hitch mounted to the rear of
the vehicle.
Recommended Tools
•
Box/band cutter
STEP 1:
Remove pallet, banding, zip-ties, and any other packaging
materials.
STEP 2:
Remove trailer hitch from vehicle receiver hitch.
STEP 3:
Insert unroller frame into vehicle trailer hitch spool-sideup. Secure in place using pin and keeper removed from
trailer hitch ball.
STEP 4:
Verify there is sufficient clearance between vehicle
tailgate, bumper, and any other overhanging structure and
the Python Wire Unroller to allow proper operation and
visibility. Do not use devices that may collide with and
damage the unroller, such as a UTV dump bed, while the
unroller is attached.
Always use two people to
handle heavy, unwieldy
components during assembly,
installation, maintenance,
removal, or movement of the
wire unroller.
WARNING
Never exceed the rated trailer tongue weight of
the vehicle hitch.
Operation
WARNING
Unrolling New Wire
Never transport the wire unroller on highways
while connected to vehicle hitch.
DANGER
It is the responsibility of the
operator to see that no one is
within twenty-five feet (25') of
the wire unroller or wire path
before and during wire unroller
rotation. Do not operate the
wire unroller with another
person near or in contact with
any part of the wire unroller.
Serious personal injury or
death may result if any attempt
is made to assist unrolling
operation by hand.
WARNING
Before you operate the attachment, check over
all pins, bolts, and connections to be sure all
are securely in place. Replace any damaged or
worn parts immediately.
STEP 1:
Shut off the vehicle engine, set the parking brake, and
remove the vehicle key.
STEP 2:
Remove spool top plate retaining pin, top plate, and spool
assembly. Set spool assembly and retaining pin aside. Invert
top plate, and slide down over frame spindle so that its flat
surface faces upwards.
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
NOTE
Ensure the rubber brake pad is installed on the spindle
below top plate.
9
Operation
(continued)
STEP 3: Check that new spool of wire has sufficient inner diameter
to fit over spindle (refer to Specifications). Slide spool of
wire over spindle, and gently set spool down onto top plate.
DANGER
WARNING
Safe operation of equipment
requires the operator's
full attention. Avoid
distractions such as radio
headphones, cell phones,
etc. while operating.
Before beginning operation, clear the work area
of objects which might be picked up and thrown
by or entangled in the wire and/or wire unroller.
STEP 4: Attach wire to starting post, and slowly drive forward to
unroll wire.
DANGER
DANGER
Never manually guide wire by hand or with tool.
Do not allow riders on the
equipment at any time.
There is no safe place for
any riders.
DANGER
Never place yourself between
the vehicle and the
attachment.
WARNING
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
CAUTION
Never exceed 10 MPH while unrolling wire.
NOTE
Excessive speed while unrolling may cause the wire spool
to over-spin and become tangled. Should that occur, come
to a stop, back up slightly to relieve tension on the wire,
and untangle the wire before continuing to unroll.
DANGER
Keep all helpers and bystanders twenty-five feet
(25’) away from the wire unroller or wire path
before and during wire unroller rotation. The
wire unroller must be positioned such that all
winding operations, including the wire path, can
be easily seen.
STEP 5: Upon reaching the end post, wrap the wire around the cleats
on the frame of the unroller. Slowly drive forward to put
tension on the wire.
WARNING
Stay clear of wire path during tensioning. Wire
may come loose or break, potentially injuring
bystanders.
STEP 6: Secure wire to the end post, and trim to length.
10
STEP 7: Loop remaining wire onto the frame cleats to prevent the
wire from snagging while driving.
Operation
WARNING
Unspooling Python Wire
Winder-Spooled Wire
Never transport the wire unroller on highways
while connected to vehicle hitch.
DANGER
It is the responsibility of the
operator to see that no one is
within twenty-five feet (25') of
the wire unroller or wire path
before and during wire unroller
rotation. Do not operate the
wire unroller with another
person near or in contact with
any part of the wire unroller.
Serious personal injury or
death may result if any attempt
is made to assist unrolling
operation by hand.
WARNING
Before you operate the attachment, check over
all pins, bolts, and connections to be sure all
are securely in place. Replace any damaged or
worn parts immediately.
STEP 1:
Shut off the vehicle engine, set the parking brake, and
remove the vehicle key.
STEP 2:
Remove spool top plate retaining pin and top plate. Spool
should be installed on frame spindle plate-side-down.
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
NOTE
STEP 3:
If unspooling barbed wire, ensure the rubber brake pad is
installed on spindle below spool. Remove rubber brake
pad when unspooling Python-spooled smooth wire.
Remove any tie wires from spooled wire. Orient spooled
wire so the cone shape of the spool assembly fills the cone
shape left in the wire by your Python Wire Winder, and set
it gently down onto the spool. Place unroller top plate on
spool, plate-side-down, aligning pin holes in top plate and
spool assembly. Reinstall retaining pin.
DANGER
Before beginning operation, clear the work area
of objects which might be picked up and thrown
by or entangled in the wire and/or wire unroller.
STEP 4:
Attach wire to starting post, and slowly drive forward to
unroll wire.
11
Operation
DANGER
(continued)
Never manually guide wire by hand or with tool.
WARNING
Safe operation of equipment
requires the operator's
full attention. Avoid
distractions such as radio
headphones, cell phones,
etc. while operating.
CAUTION
Never exceed 10 MPH while unrolling wire.
NOTE
DANGER
DANGER
Do not allow riders on the
equipment at any time.
There is no safe place for
any riders.
DANGER
Never place yourself between
the vehicle and the
attachment.
Excessive speed while unrolling may cause the wire spool
to over-spin and become tangled. Should that occur, come
to a stop, back up slightly to relieve tension on the wire,
and untangle the wire before continuing to unroll.
Keep all helpers and bystanders twenty-five feet
(25’) away from the wire unroller or wire path
before and during wire unroller rotation. The
wire unroller must be positioned such that all
winding operations, including the wire path, can
be easily seen.
STEP 5:
Upon reaching the end post, wrap the wire around the cleats
on the frame of the unroller. Slowly drive forward to put
tension on the wire.
WARNING
Keep hands, feet, hair,
jewelry, and clothing away
from all moving and/or
rotating parts.
WARNING
Stay clear of wire path during tensioning. Wire
may come loose or break, potentially injuring
bystanders.
12
STEP 6:
Secure wire to the end post, and trim to length.
STEP 7:
Loop remaining wire onto the frame cleats to prevent the
wire from snagging while driving.
Operation
Straightening Posts
DANGER
The Python Wire Unroller has two slots for straightening posts: a
circular slot for posts up to 5/8” diameter (rebar), and a T-post slot.
STEP 1:
Shut off the vehicle engine, set the parking brake, and
remove the vehicle key.
STEP 2:
Insert post into the appropriate slot up to bent section. With
moderate force, bend post back into shape.
Never place yourself between
the vehicle and the
attachment.
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
Removal &
Storage
DANGER
Never allow anyone under the
attachment at any time.
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
WARNING
Never transport the wire unroller on highways
while connected to vehicle hitch.
Before storage, the Python Wire Unroller should be thoroughly
cleaned, washing off all dirt and grime. Always store the wire
unroller in a dry, covered location.
STEP 1:
Separate the wire unroller from the vehicle, and lower it
onto a flat, level surface in an area where children do not
play. Securely block and support the wire unroller.
STEP 2:
Replace any damaged or missing safety signs.
13
Troubleshooting
Problem
Possible Cause
Solution
Python Wire Winder-spooled
Wire wound too loosely
wire unspooling erratically
Wind wire more tightly. Refer to Python
Wire Winder Operator’s Manual.
Wire pulling tightly around
spool while unspooling
Remove rubber brake pad.
Rubber brake pad not needed for
unspooling smooth wire
Ensure the rubber brake pad is installed.
Replace rubber brake pad.
Drive at a slower speed.
Rubber brake pad missing
Wire tangling/seizing while
Rubber brake pad worn
unspooling
Wire spool over-spinning
Rubber Brake Pad Usage
Typically, rubber brake pad usage is as follows. If you are having difficulty unrolling wire, try installing or
removing the rubber brake pad.
Use Rubber Brake Pad?
New wire
Python-spooled wire
Smooth wire
Barbed wire
Yes
No
Yes
Yes
For additional assistance, please call your dealer or contact Danuser direct:
Tel: (573) 642-2246
Fax: (573) 642-2240
E-mail: [email protected]
Maintenance
WARNING
Personal protection
equipment including safety
glasses, hearing protection,
safety shoes, gloves, and
ear plugs are recommended
during assembly, installation,
operation, maintenance,
removal, or movement of the
wire unroller.
Proper maintenance is key to the long life of the wire unroller. Careful
inspection and routine maintenance helps avoid costly downtime and
repair. Do not use the Python Wire Unroller with any damaged parts.
DANGER
Never replace the spool retaining pin with anything other
than one that meets the original equipment manufacturer’s
standards and requirements. A longer, or protuding,
fastener is more likely to grab clothing or gloves, which
can result in serious injury or death.
WARNING
Do not modify the wire unroller. Modifications may
weaken the integrity of the wire unroller and may impair
the safety, function, life, and performance of the wire
unroller.
Maintenance
14
Inspect the attachment for any damage or worn
parts. Repair or replace as necessary.
Check for damaged or missing safety signs.
Replace as necessary.
Visually inspect all welds for cracks.
Check rubber brake pad for wear. Replace as
necessary.
Interval
Before each use
Before each use
Before each use
Before each use
WARNING
Parts
This product can expose you to chemicals known to the State of
California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov/product.
2
1
3
4
5
REF. NO.
PART NO.
DESCRIPTION
QTY.
1
2
3
4
5
20012
180609
180608
180622
180607
Retaining Pin
Top Plate Assembly
Spool Assembly
Rubber Brake Pad
Frame Assembly
1
1
1
1
1
Python Wire Winder
Python Wire Winder
PN 170610 - The Python Wire Winder connects onto a
hydraulic auger drive unit with 2” hex shaft, and can wind
up to 6 miles of smooth or 3/4 mile of barbed wire into
convenient rolls.
15
DANUSER
Warranty
LIMITED WARRANTY
Danuser LLC (“Danuser”) warrants its products, under normal use and maintenance, to be free from defects in material
and workmanship for period(s) specified below from the purchase date from an authorized Danuser Dealer. Start of the
warranty period is determined by purchase date. Proof of purchase may be required. This Limited Warranty is extended
only to the original purchaser of Danuser products.
Python Wire Unroller - 1 Year
Wear Items Not Covered Under Warranty - Rubber Brake Pad
1.
During the applicable warranty period, Danuser, at its option, will repair or replace any part determined by Danuser
to be defective. Such repair or replacement shall take place at Danuser’s factory or a location designated by
Danuser. Under no circumstances shall Danuser be obligated for the cost of any repair or replacement by anyone
other than Danuser without its express written consent.
2.
Parts may not be returned without written authorization from Danuser.
3.
Some purchased components, including but not limited to hydraulic components, are subject to the inspection and
warranty of the respective manufacturer. Thus, delays in a warranty determination can be expected while Danuser
awaits their decision.
4.
This warranty is void if any attempt is made to make field repairs to hydraulic components. To qualify for warranty
inspection, the “failed” part(s) must be returned in its original “failed” condition.
5.
To make a claim under this warranty, first contact your authorized Danuser Dealer. The Danuser Dealer shall
complete the Warranty Claim Form and obtain written authorization from Danuser to return parts. All warranty
claims must include detailed information regarding make and model of vehicle on which the Danuser product was
mounted, hours of use, description of events that led up to the failure, and any other information helpful in reviewing
the warranty claim. All warranty returns must be prepaid. Shipments arriving at our factory on a freight collect
basis will be refused by our receiving department. The freight charge will be credited if the parts are determined
by Danuser to be defective, and the associated freight costs in returning those parts will be prepaid by Danuser.
NOTE: Hydraulic components must arrive with all ports sealed from dirt and moisture. If a hydraulic component
arrives with open ports, the warranty is void and no inspection will be made.
6.
Products or parts thereof which, as determined by Danuser’s examination, show wear from normal use, have been
improperly operated, damaged by accident or negligence, field repaired, altered or modified are not considered
defective in material and workmanship and are not covered by this warranty. This warranty does not apply to parts
subject to normal wear ("Wear Items") or to damage caused by the failure to perform recommended maintenance
or to replace worn parts. This warranty shall not obligate Danuser to bear any cost of labor for field repair,
replacement, testing, or adjustment nor for damage caused by accident, abuse, misuse, or environmental elements.
7.
Any parts or labor required to repair or replace parts not covered under this warranty will be charged to the customer.
Parts repaired or replaced by Danuser are then covered by this warranty only for the remainder of the original
warranty as if such parts were original parts.
8.
Danuser reserves the right to change its specifications and designs at any time.
This warranty is exclusive and in lieu of all other express warranties, if any, including the implied warranties of
merchantability and fitness for a particular purpose. It shall not extend beyond the duration of the expressed warranty
provided herein and the remedy for violations of any implied warranty shall be limited to repair or replacement of the
defective part pursuant to the terms contained herein. No employee, dealer, salesman, or representative is authorized to
change this warranty in any way or grant any other warranty. Danuser shall not be liable for any consequential,
incidental, or punitive damages, losses, or expenses, including those resulting from or caused by any defects.
Danuser LLC
500 E. 3rd St.
P.O. Box 368
Fulton, MO 65251
Tel:
(573) 642-2246
Fax:
(573) 642-2240
E-mail: [email protected]
Website: www.danuser.com
Form No. 3475
">