IQ7 Design Guide User Manual IQ7 Design Guide for IQ7-US15W and IQ7-DB-MITX

IQ7 Design Guide User Manual  IQ7 Design Guide for IQ7-US15W and IQ7-DB-MITX
IQ7 Design Guide
IEI Technology Corp.
IQ7 Design Guide
IQ7 Design Guide for IQ7-US15W and IQ7-DB-MITX
User Manual
Page i
Rev. 1.01 – 22 July, 2009
IQ7 Design Guide
Revision
Date
Version
Changes
22 July, 2009
1.01
Various updates and changes
19 May, 2009
1.00
Initial release
Page ii
IQ7 Design Guide
Copyright
COPYRIGHT NOTICE
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
TRADEMARKS
All registered trademarks and product names mentioned herein are used for identification
purposes only and may be trademarks and/or registered trademarks of their respective
owners.
Page iii
IQ7 Design Guide
Table of Contents
1 IQ7-US15W INTRODUCTION.................................................................................... 1
1.1 IQ7-US15W .............................................................................................................. 2
1.2 BENEFITS ................................................................................................................... 2
1.3 FEATURES ................................................................................................................... 3
1.4 CONNECTORS ............................................................................................................. 3
1.5 DIMENSIONS ............................................................................................................... 3
1.6 DATA FLOW ................................................................................................................ 5
1.7 TECHNICAL SPECIFICATIONS ...................................................................................... 5
2 IQ7-US15W CONNECTOR PINOUTS....................................................................... 7
2.1 PERIPHERAL INTERFACE CONNECTORS....................................................................... 8
2.2 LAYOUT...................................................................................................................... 8
2.3 CONNECTOR PINOUTS ................................................................................................ 8
2.3.1 QSeven Connector ............................................................................................. 9
2.3.2 IDE Connector ................................................................................................. 13
3 IQ7-DB-MITX INTRODUCTION............................................................................. 16
3.1 INTRODUCTION......................................................................................................... 17
3.2 BENEFITS ................................................................................................................. 17
3.3 FEATURES ................................................................................................................. 18
3.4 CONNECTORS ........................................................................................................... 19
3.5 DIMENSIONS ............................................................................................................. 20
3.6 DATA FLOW .............................................................................................................. 23
3.7 TECHNICAL SPECIFICATIONS .................................................................................... 24
4 IQ7-DB-MITX CONNECTOR PINOUTS ................................................................ 26
4.1 PERIPHERAL INTERFACE CONNECTORS..................................................................... 27
4.1.1 Layout .............................................................................................................. 27
4.1.2 Peripheral Interface Connectors ..................................................................... 28
4.1.3 External Interface Panel Connectors............................................................... 29
4.2 INTERNAL PERIPHERAL CONNECTORS ...................................................................... 29
Page iv
IQ7 Design Guide
4.2.1 ATX Power Connector ..................................................................................... 29
4.2.2 Backlight Inverter Connector .......................................................................... 30
4.2.3 CompactFlash® Slot........................................................................................ 31
4.2.4 Digital I/O Connector ...................................................................................... 32
4.2.5 Fan Connector ................................................................................................. 33
4.2.6 Front Panel Connector .................................................................................... 34
4.2.7 IDE Connector ................................................................................................. 35
4.2.8 IDE (CPU Module to Baseboard).................................................................... 37
4.2.9 LVDS Connector .............................................................................................. 38
4.2.10 Mini USB Port................................................................................................ 39
4.2.11 PCI Express x1 Slot........................................................................................ 40
4.2.12 PCIe Mini Card Slot ...................................................................................... 41
4.2.13 Power Button ................................................................................................. 43
4.2.14 QSeven Connector ......................................................................................... 43
4.2.15 Reset Button ................................................................................................... 48
4.2.16 SATA Drive Connectors ................................................................................. 48
4.2.17 SATA Power Connectors ................................................................................ 49
4.2.18 SDVO Connector............................................................................................ 50
4.2.19 Serial Port Connectors .................................................................................. 51
4.2.20 TTL Connector ............................................................................................... 52
4.2.21 USB Connector .............................................................................................. 53
4.3 EXTERNAL INTERFACE CONNECTORS ....................................................................... 55
4.3.1 Audio Connector .............................................................................................. 55
4.3.2 Ethernet Connector.......................................................................................... 56
4.3.3 Keyboard and Mouse Connector ..................................................................... 57
4.3.4 Parallel Port Connector .................................................................................. 58
4.3.5 Serial Port Connector ...................................................................................... 59
4.3.6 USB Ports......................................................................................................... 60
4.3.7 VGA Connector ................................................................................................ 61
4.4 JUMPER SETTINGS .................................................................................................... 62
4.4.1 AT/ATX Mode Selection ................................................................................... 63
4.4.2 Clear CMOS Jumper........................................................................................ 64
4.4.3 CompactFlash® Master/Slave Selection ......................................................... 65
4.4.4 CompactFlash® Voltage Selection .................................................................. 65
4.4.5 LAN & PCIe Enable/Disable ........................................................................... 65
Page v
IQ7 Design Guide
4.4.6 TTL Voltage Selection ...................................................................................... 66
4.4.7 SATA & Graphics Settings ............................................................................... 66
4.4.8 TTL Enabled/Disable ....................................................................................... 67
5 INSTALLATION ......................................................................................................... 68
5.1 ANTI-STATIC PRECAUTIONS ...................................................................................... 69
5.2 INSTALLATION CONSIDERATIONS .............................................................................. 69
5.3 CPU MODULE INSTALLATION .................................................................................. 71
6 BIOS .............................................................................................................................. 73
6.1 INTRODUCTION......................................................................................................... 74
6.1.1 Starting Setup................................................................................................... 74
6.1.2 Using Setup ...................................................................................................... 74
6.1.3 Getting Help..................................................................................................... 75
6.1.4 Unable to Reboot After Configuration Changes.............................................. 75
6.1.5 BIOS Menu Bar................................................................................................ 75
6.2 MAIN........................................................................................................................ 76
6.3 ADVANCED ............................................................................................................... 77
6.3.1 CPU Configuration.......................................................................................... 78
6.3.2 IDE Configuration ........................................................................................... 79
6.3.2.1 IDE Master, IDE Slave ............................................................................. 80
6.3.3 Super IO Configuration ................................................................................... 84
6.3.4 Hardware Health Configuration...................................................................... 88
6.3.5 AHCI Configuration......................................................................................... 91
6.3.5.1 AHCI Port n .............................................................................................. 92
6.3.6 Intel AMT Configuration.................................................................................. 93
6.3.6.1 ME Subsystem Configuration................................................................... 94
6.3.7 Remote Access Configuration .......................................................................... 96
6.3.8 USB Configuration........................................................................................... 98
6.3.8.1 USB Mass Storage Device Configuration............................................... 101
6.4 PCI/PNP................................................................................................................. 103
6.5 BOOT...................................................................................................................... 104
6.5.1 Boot Settings Configuration........................................................................... 105
6.5.2 Boot Device Priority ...................................................................................... 107
6.5.3 Hard Disk Drives ........................................................................................... 108
Page vi
IQ7 Design Guide
6.5.4 Removable Drives .......................................................................................... 108
6.5.5 CD/DVD Drives ............................................................................................. 109
6.6 SECURITY ............................................................................................................... 109
6.7 CHIPSET ..................................................................................................................111
6.7.1 Northbridge Configuration ............................................................................. 111
6.7.2 Southbridge Configuration .............................................................................113
6.8 EXIT ........................................................................................................................114
A BIOS OPTIONS .........................................................................................................116
B TERMINOLOGY...................................................................................................... 120
C HAZARDOUS MATERIALS DISCLOSURE ....................................................... 124
C.1 HAZARDOUS MATERIALS DISCLOSURE TABLE FOR IPB PRODUCTS CERTIFIED AS
ROHS COMPLIANT UNDER 2002/95/EC WITHOUT MERCURY ..................................... 125
Page vii
IQ7 Design Guide
List of Figures
Figure 1-1: IQ7-US15W IQ7 Design Guide....................................................................................2
Figure 1-2: Connectors ..................................................................................................................3
Figure 1-3: IQ7-US15W Dimensions (mm) ...................................................................................4
Figure 1-4: Data Flow Diagram......................................................................................................5
Figure 2-1: Connector and Jumper Locations.............................................................................8
Figure 2-2: QSeven Connector......................................................................................................9
Figure 2-3: IDE Connector ...........................................................................................................14
Figure 3-1: IQ7-DB-MITX ..............................................................................................................17
Figure 3-2: Top Connectors.........................................................................................................19
Figure 3-3: Rear Panel Connectors.............................................................................................20
Figure 3-4: IQ7-DB-MITX Dimensions (mm)...............................................................................21
Figure 3-5: External Interface Panel Dimensions (mm) ............................................................22
Figure 3-6: Data Flow Diagram....................................................................................................23
Figure 4-1: Connector and Jumper Locations...........................................................................27
Figure 4-2: ATX Power Connector Pinout Locations................................................................30
Figure 4-3: Backlight Inverter Connector...................................................................................31
Figure 4-4: CompactFlash® Slot Location.................................................................................32
Figure 4-5: Digital I/O Connector Locations ..............................................................................33
Figure 4-6: Fan Connector Location...........................................................................................34
Figure 4-7: Front Panel Connector Pinout Locations ...............................................................35
Figure 4-8: IDE Connector Locations .........................................................................................36
Figure 4-9: CPU Module to Baseboard IDE Connector Location.............................................37
Figure 4-10: LVDS Connector Location......................................................................................38
Figure 4-11: Mini USB Port Location ..........................................................................................40
Figure 4-12: PCIe x1 Connector Location ..................................................................................41
Figure 4-13: PCIe Mini Card Slot Location .................................................................................42
Figure 4-14: Power Button Location...........................................................................................43
Figure 4-15: QSeven Connector Location..................................................................................44
Figure 4-16: Reset Button Location............................................................................................48
Figure 4-17: SATA Drive Connector Locations .........................................................................49
Page viii
IQ7 Design Guide
Figure 4-18: SATA Power Connector Locations .......................................................................49
Figure 4-19: Serial Port Connector Locations ...........................................................................51
Figure 4-20: TTL Connector Location.........................................................................................52
Figure 4-21: USB Connector Locations......................................................................................54
Figure 4-22: External Interface Connectors...............................................................................55
Figure 4-23: Audio Connector .....................................................................................................56
Figure 4-24: Ethernet Connector.................................................................................................57
Figure 4-25: PS/2 Connector .......................................................................................................58
Figure 4-26: Parallel Port Connector Location ..........................................................................59
Figure 4-27: Serial Port Pinout Locations ..................................................................................60
Figure 4-28: VGA Connector .......................................................................................................61
Figure 4–29: Jumpers ..................................................................................................................63
Figure 5-1: Installing the QSeven CPU Module .........................................................................72
Page ix
IQ7 Design Guide
List of Tables
Table 1-1: Technical Specifications..............................................................................................6
Table 2-1: Peripheral Interface Connectors .................................................................................8
Table 2-2: QSeven Connector .....................................................................................................13
Table 2-3: IDE Connector.............................................................................................................15
Table 3-1: Technical Specifications............................................................................................25
Table 4-1: Peripheral Interface Connectors ...............................................................................28
Table 4-2: Rear Panel Connectors ..............................................................................................29
Table 4-3: ATX Power Connector Pinouts .................................................................................30
Table 4-4: Backlight Inverter Connector ....................................................................................31
Table 4-5: Digital I/O Connector Pinouts....................................................................................33
Table 4-6: Fan Connector Pinouts ..............................................................................................34
Table 4-7: Front Panel Connector Pinouts.................................................................................35
Table 4-8: IDE Connector Pinouts...............................................................................................37
Table 4-9: CPU Module to Baseboard IDE Pinouts ...................................................................38
Table 4-10: LVDS Connector Pinouts .........................................................................................39
Table 4-11: Mini USB Port Pinouts..............................................................................................40
Table 4-12: PCIe x1 Slot Pinouts.................................................................................................41
Table 4-13: PCIe Mini Card Slot Pinouts ....................................................................................43
Table 4-14: QSeven Connector Pinouts .....................................................................................48
Table 4-15: SATA Power Connector Pinouts.............................................................................50
Table 4-16: IDE Connector Pinouts.............................................................................................51
Table 4-17: Serial Port Connector Pinouts ................................................................................52
Table 4-18: TTL Connector Pinouts ............................................................................................53
Table 4-19: USB Port Connector Pinouts...................................................................................54
Table 4-20: Audio Connector Pinouts ........................................................................................56
Table 4-21: Ethernet Connector Pinouts ....................................................................................56
Table 4-22: Connector LEDs........................................................................................................57
Table 4-23: PS/2 Connectors .......................................................................................................58
Table 4-24: Parallel Port Connector Pinouts .............................................................................59
Table 4-25: Serial Port Pinouts....................................................................................................60
Page x
IQ7 Design Guide
Table 4-26: USB Connector Pinouts ...........................................................................................61
Table 4-27: VGA Connector Pinouts...........................................................................................61
Table 4-28: Jumpers .....................................................................................................................62
Table 4-29: AT/ATX Mode Selection ...........................................................................................63
Table 4-30: AT/ATX Mode Selection ...........................................................................................64
Table 4-31: Clear CMOS Jumper Settings..................................................................................64
Table 4-32: CompactFlash® Master/Slave Selection ................................................................65
Table 4-33: CompactFlash® Voltage Selection .........................................................................65
Table 4-34: LAN & PCIe Enable/Disable .....................................................................................66
Table 4-35: LVDS Voltage Selection ...........................................................................................66
Table 4-36: LAN & PCIe Enable/Disable .....................................................................................67
Table 4-37: TTL Enable/Disable...................................................................................................67
Table 6-1: BIOS Navigation Keys ................................................................................................75
Page xi
IQ7 Design Guide
BIOS Menus
BIOS Menu 1: Main .......................................................................................................................76
BIOS Menu 2: Advanced ..............................................................................................................77
BIOS Menu 3: CPU Configuration ...............................................................................................78
BIOS Menu 4: IDE Configuration.................................................................................................79
BIOS Menu 5: IDE Master and IDE Slave Configuration ...........................................................80
BIOS Menu 6: Super IO Configuration........................................................................................84
BIOS Menu 7: Hardware Health Configuration ..........................................................................88
BIOS Menu 8: AHCI Configuration..............................................................................................91
BIOS Menu 9: AHCI Port n Configuration Menu........................................................................92
BIOS Menu 10: Intel AMT Configuration ....................................................................................93
BIOS Menu 11: ME Subsystem Configuration...........................................................................94
BIOS Menu 12: Remote Access Configuration..........................................................................96
BIOS Menu 13: USB Configuration .............................................................................................98
BIOS Menu 14: USB Mass Storage Device Configuration ..................................................... 101
BIOS Menu 15: PCI/PnP Configuration.................................................................................... 103
BIOS Menu 16: Boot .................................................................................................................. 104
BIOS Menu 17: Boot Settings Configuration .......................................................................... 105
BIOS Menu 18: Boot Device Priority Settings ........................................................................ 107
BIOS Menu 19: Hard Disk Drives ............................................................................................. 108
BIOS Menu 20: Removable Drives ........................................................................................... 108
BIOS Menu 21: CD/DVD Drives ................................................................................................ 109
BIOS Menu 22: Security ............................................................................................................ 109
BIOS Menu 23: Chipset ............................................................................................................. 111
BIOS Menu 24: Northbridge Chipset Configuration............................................................... 111
BIOS Menu 25: Southbridge Chipset Configuration .............................................................. 113
BIOS Menu 26: Exit.................................................................................................................... 114
Page xii
IQ7 Design Guide
Chapter
1
1 IQ7-US15W Introduction
Page 1
IQ7 Design Guide
1.1 IQ7-US15W
Figure 1-1: IQ7-US15W IQ7 Design Guide
The IQ7-US15W is a QSeven CPU Module with a 1.1 GHz Intel® Atom™ Z510 or
1.6 GHz Intel® Atom™ Z530 CPU.
The IQ7-US15W is designed for applications that require fanless operation. The low
power CPUs don't require active cooling and stay within specified heat range using the
included cooling solution.
As part of the QSeven standard, an API software interface is defined for the embedded
features such as a watchdog timer, I²C bus, LCD backlight control, BIOS user storage
area and temperature control.
Graphics capabilities include SDVO and 18/24-bit LVDS to the baseboard.
Other interfaces include IDE, USB and HD Audio.
1.2 Benefits
Some of the IQ7-US15W motherboard benefits include,
Page 2
ƒ
Low power consumption
ƒ
Wide range of I/O interfaces
IQ7 Design Guide
ƒ
Standard API software interface for embedded features
1.3 Features
Some of the IQ7-US15W motherboard features are listed below:
ƒ
QSeven form factor
ƒ
RoHS compliant
ƒ
PCIe x1 expansion
ƒ
Includes 1.0 GB DDR2
1.4 Connectors
The connectors on the IQ7-US15W are shown in the figure below.
Figure 1-2: Connectors
1.5 Dimensions
The main dimensions of the IQ7-US15W are shown in the diagram below.
ƒ
Length:
70 mm
ƒ
Width:
70 mm
Page 3
IQ7 Design Guide
Figure 1-3: IQ7-US15W Dimensions (mm)
Page 4
IQ7 Design Guide
1.6 Data Flow
Figure 1-4 shows the data flow between the system chipset, the CPU and other
5
components installed on the motherboard.
1.1 GHz Intel® Atom™ Z510
1.6 GHz Intel® Atom™ Z530
FSB
Intel® US-15W
SDVO
DDR2
18/24-bit LVDS
2 x PCIe x1
LPC
High Definition Audio
1.0 GB DDR2
CPLD
EPM570T100
QSeven Connector
SPI Flash
SDIO/MMC
8 x USB
FWH Flash
LPC
IDE
FPC connector
SMBUS
Smart Fan Control
H/W Monitor
Winbond
W83L784
H/W Monitor
Figure 1-4: Data Flow Diagram
1.7 Technical Specifications
IQ7-US15W technical specifications are listed in Table 1-1.
5
Specification
IQ7-US15W
Form Factor
QSeven
Page 5
IQ7 Design Guide
Specification
IQ7-US15W
Socket
Embedded
CPU Supported
1.1 GHz Intel® Atom™ Z510,
1.6 GHz Intel® Atom™ Z530
Front Side Bus (FSB)
400 MHz,
533 MHz
System Chipset
Intel® US-15W
Memory
1.0 GB DDR2
Audio
HD audio connection to baseboard
BIOS
FWH BIOS
Expansion
2 x PCIe x1 to baseboard
PCIe
I/O Interface Connectors
Display port
SDVO to baseboard
24-bit LVDS to baseboard
8 x USB to baseboard
USB
Storage
Serial ATA
2 x SATA to baseboard
Environmental and Power Specifications
Power Supply
5 V AT/ATX supported
Power Consumption
1.255 A @ 5 V (1.1 GHz Intel® Atom™ Z510, 1 GB DDR2)
1.34 A @ 5 V (1.6 GHz Intel® Atom™ Z530, 1 GB DDR2)
Operating temperature
0ºC ~ 60ºC (requires cooler and silicone heat sink paste)
Humidity
0% ~ 95% (non-condensing)
Physical Specifications
Dimensions
70 mm x 70 mm
Weight GW/NW
600 g/100 g
Table 1-1: Technical Specifications
Page 6
IQ7 Design Guide
Chapter
2
2 IQ7-US15W
Connector Pinouts
Page 7
IQ7 Design Guide
2.1 Peripheral Interface Connectors
This chapter gives an overview of all the connectors on the IQ7-US15W and their pin
definitions.
2.2 Layout
Figure 2-1 shows the on-board peripheral connectors, rear panel peripheral connectors
5
and on-board jumpers.
Figure 2-1: Connector and Jumper Locations
2.3 Connector Pinouts
Table 2-1 shows a list of the peripheral interface connectors on the IQ7-US15W. Detailed
descriptions of these connectors can be found below.
Connector
Type
Label
QSeven Connector
QSeven connector
J1
IDE Connector
Flat cable
CN16
Table 2-1: Peripheral Interface Connectors
Page 8
IQ7 Design Guide
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the IQ7-US15W.
2.3.1 QSeven Connector
CN Label:
J1
CN Type:
QSeven connector
CN Location:
See Figure 2-2
CN Pinouts:
See Table 2-2
5
5
Provides the interface for all the connectors.
Figure 2-2: QSeven Connector
Pin
Description
Pin
Description
1
GND
2
GND
3
GBE_MDI3-
4
GBE_MDI2-
5
GBE_MDI3+
6
GBE_MDI2+
7
GBE_LINK100#
8
GBE_LINK1000#
9
GBE_MDI1-
10
GBE_MDI0-
11
GBE_MDI1+
12
GBE_MDI0+
Page 9
IQ7 Design Guide
Pin
Description
Pin
Description
13
GBE_LINK#
14
GBE_ACT#
15
GBE_CTREF
16
SUS_S5#
17
WAKE#
18
SUS_S3#
19
SUS_STAT#
20
PWRBTN#
21
SLP_BTN#
22
LID_BTN#
23
GND
24
GND
KEY
KEY
25
GND
26
PWGIN
27
BATLOW#
28
RSTBTN#
29
SATA0_TX+
30
SATA1_TX+
31
SATA0_TX-
32
SATA1_TX-
33
SATA_ACT#
34
GND
35
SATA0_RX+
36
SATA1_RX+
37
SATA0_RX-
38
SATA1_RX-
39
GND
40
GND
41
BIOS_DISABLE#
42
SDIO_CLK#
43
SDIO_CD#
44
SDIO_LED
45
SDIO_CMD
46
SDIO_WP
47
SDIO_PWR#
48
SDIO_DAT1
49
SDIO_DAT0
50
SDIO_DAT3
51
SDIO_DAT2
52
SDIO_DAT5
53
SDIO_DAT4
54
SDIO_DAT7
55
SDIO_DAT6
56
RSVD
57
GND
58
GND
59
HDA_SYNC
60
SMB_CLK
61
HDA_RST#
62
SMB_DAT
63
HDA_BITCLK
64
SMB_ALERT#
65
HDA_SDI
66
I2C_CLK
67
HDA_SDO
68
I2C_DAT
69
THRM#
70
WDTRIG#
71
THRMTRIP#
72
WDOUT
73
GND
74
GND
Page 10
IQ7 Design Guide
Pin
Description
Pin
Description
75
USB_P7-
76
USB_P6-
77
USB_P7+
78
USB_P6+
79
USB_6_7_OC#
80
USB_4_5_OC#
81
USB_P5-
82
USB_P4-
83
USB_P5+
84
USB_P4+
85
USB_2_3_OC#
86
USB_0_1_OC#
87
USB_P3-
88
USB_P2-
89
USB_P3+
90
USB_P2+
91
USB_HOST_PRES#
92
USB_HC_SEL
93
USB_P1-
94
USB_P0-
95
USB_P1+
96
USB_P0+
97
GND
98
GND
99
LVDS_A0+
100
LVDS_B0+
101
LVDS_A0-
102
LVDS_B0-
103
LVDS_A1+
104
LVDS_B1+
105
LVDS_A1-
106
LVDS_B1-
107
LVDS_A2+
108
LVDS_B2+
109
LVDS_A2-
110
LVDS_B2-
111
LVDS_PPEN
112
LVDS_BLEN
113
LVDS_A3+
114
LVDS_B3+
115
LVDS_A3-
116
LVDS_B3-
117
GND
118
GND
119
LVDS_A_CLK+
120
LVDS_B_CLK+
121
LVDS_A_CLK-
122
LVDS_B_CLK-
123
LVDS_BLT_CTRL
124
RSVD
125
LVDS_DID_DAT
126
LVDS_BLC_DAT
127
LVDS_DID_CLK
128
LVDS_BLC_CLK
129
RSVD
130
RSVD
131
SDVO_BCLK+
132
SDVO_INT+
133
SDVO_BCLK-
134
SDVO_INT-
135
GND
136
GND
137
SDVO_GREEN+
138
SDVO_FLDSTALL+
Page 11
IQ7 Design Guide
Pin
Description
Pin
Description
139
SDVO_GREEN-
140
SDVO_FLDSTALL-
141
GND
142
GND
143
SDVO_BLUE+
144
SDVO_TVCLKIN+
145
SDVO_BLUE-
146
SDVO_TVCLKIN-
147
GND
148
GND
149
SDVO_RED+
150
SDVO_CTRL_DAT
151
SDVO_RED-
152
SDVO_CTRL_CLK
153
HDMI_HPD#
154
DP_HPD#
155
PCIE_CLK_REF+
156
PCIE_WAKE#
157
PCIE_CLK_REF-
158
PCIE_RST#
159
GND
160
GND
161
PCIE3_TX+
162
PCIE3_RX+
163
PCIE3_TX-
164
PCIE3_RX-
165
GND
166
GND
167
PCIE2_TX+
168
PCIE2_RX+
169
PCIE2_TX-
170
PCIE2_RX-
171
EXCD0_PERST#
172
EXCD1_PERST#
173
PCIE1_TX+
174
PCIE1_RX+
175
PCIE1_TX-
176
PCIE1_RX-
177
EXCD0_CPPE#
178
EXCD1_CPPE#
179
PCIE0_TX+
180
PCIE0_RX+
181
PCIE0_TX-
182
PCIE0_RX-
183
GND
184
GND
185
LPC_AD0
186
LPC_AD1
187
LPC_AD2
188
LPC_AD3
189
LPC_CLK
190
LPC_FRAME#
191
SERIRQ
192
LPC_LDRQ#
193
VCC_RTC
194
SPKR
195
FAN_TACHOIN
196
FAN_PWMOUT
197
GND
198
GND
199
RSVD
200
RSVD
201
RSVD
202
RSVD
Page 12
IQ7 Design Guide
Pin
Description
Pin
Description
203
RSVD
204
MFG_NC4
205
VCC_5V_SB
206
VCC_5V_SB
207
MFG_NC0
208
MFG_NC2
209
MFG_NC1
210
MFG_NC3
211
VCC
212
VCC
213
VCC
214
VCC
215
VCC
216
VCC
217
VCC
218
VCC
219
VCC
220
VCC
221
VCC
222
VCC
223
VCC
224
VCC
225
VCC
226
VCC
227
VCC
228
VCC
229
VCC
230
VCC
Table 2-2: QSeven Connector
2.3.2 IDE Connector
CN Label:
CN16
CN Type:
Flat cable connector (FPC40P_0D5M-88511)
CN Location:
See Figure 2-3
CN Pinouts:
See Table 2-3
5
5
Connects to the baseboard through a flat panel connector, then to the IDE device through
an IDE connector.
Page 13
IQ7 Design Guide
Figure 2-3: IDE Connector
Pin
Description
1
NC
2
NC
3
IDERST
4
GND
5
D7
6
D8
7
D6
8
D9
9
D5
10
D10
11
D4
12
D11
13
D3
14
D12
15
D2
16
D13
17
D1
18
D14
19
D0
20
D15
21
GND
22
DMARQ
Page 14
IQ7 Design Guide
Pin
Description
23
GND
24
IOW#
25
IOR#
26
GND
27
IORDY
28
GND
29
DMACK#
30
IRQ
31
ADD1
32
CBLIB#
33
ADD0
34
ADD2
35
CS0
36
CS1
37
DASP
38
3.3V
39
3.3V
40
NC
Table 2-3: IDE Connector
Page 15
IQ7 Design Guide
Chapter
3
3 IQ7-DB-MITX
Introduction
Page 16
IQ7 Design Guide
3.1 Introduction
Figure 3-1: IQ7-DB-MITX
The IQ7-DB-MITX is a MiniITX baseboard for a QSeven CPU module. The QSeven
standard specifies a TDP less than 12 W, ideal for low power, fanless applications.
The CPU and chipset are both a part of the CPU module, and the baseboard provides all
the connectors.
Three SATA ports, a 44-pin IDE connection and a CompactFlash® card slot provide
storage capabilities.
Graphics capabilities include a VGA port on the rear I/O panel through the SDVO
connection. There is also an 18/24 bit LVDS and, optionally, LVDS to 18/24 bit TTL.
Networking is provided through two Gigabit Ethernet slots connected through PCIe x1
channels.
Expansion capabilities include a parallel port, PS/2 connectors, four serial ports, PCIe x1
expansion card slot and PCIe Mini card slot.
3.2 Benefits
Some of the IQ7-DB-MITX motherboard benefits include,
Page 17
IQ7 Design Guide
ƒ
Operating reliably in harsh industrial environments up to 70°C
ƒ
The system is always available and will reboot if the system crashes
ƒ
Powerful processor options are ideal for computing intensive applications
3.3 Features
Some of the IQ7-DB-MITX motherboard features are listed below:
Page 18
ƒ
MiniITX form factor
ƒ
RoHS compliant
ƒ
QSeven CPU module connector
ƒ
Two Gigabit Ethernet controllers
ƒ
Integrated audio
IQ7 Design Guide
3.4 Connectors
The connectors on the IQ7-DB-MITX are shown in the figure below.
Figure 3-2: Top Connectors
Page 19
IQ7 Design Guide
Figure 3-3: Rear Panel Connectors
3.5 Dimensions
The main dimensions of the IQ7-DB-MITX are shown in the diagram below.
Page 20
ƒ
Length:
170 mm
ƒ
Width:
170 mm
IQ7 Design Guide
Figure 3-4: IQ7-DB-MITX Dimensions (mm)
Page 21
IQ7 Design Guide
The external peripheral interface connectors are shown below.
Figure 3-5: External Interface Panel Dimensions (mm)
Page 22
IQ7 Design Guide
3.6 Data Flow
Figure 1-4 shows the data flow between the system chipset, the CPU and other
5
components installed on the motherboard.
SMSC3114
WDT
Port 80 (Debug)
PS/2
LPC
Digital I/O
Line out
External Mic
Realtek
ALC888
HD
Audio
LPT
COM1
2 x SATA
6 x USB
USB Client
Fan
EEPROM
SATA
COM2
USB
COM3
USB
COM4
Smart Fan
I2C
QSeven
Module
QSeven Connector
SD Slot
LAN
LVDS
PCIe Mini Card
OR
GbE
LVDS
USB
PI2PCIE412-D
PCIe x1
OR
IDE Connector
CompactFlash®
Realtek
RTL8111CP
IDE
-toSATA
SATA
LAN
SDVO
PCIe x1
OR
PI2PCIE412-D
PI2PCIE412-D
PCIe x1
Realtek
RTL8111CP
LAN
Chrontel
CH7308A/B
CRT
CRT
SDVO
SDVO
(Optional)
Figure 3-6: Data Flow Diagram
Page 23
IQ7 Design Guide
3.7 Technical Specifications
IQ7-DB-MITX technical specifications are listed in Table 1-1.
5
Specification
IQ7 Design Guide
Form Factor
MiniITX
CPU Module
QSeven
Front Side Bus (FSB)
400 MHz or 533 MHz
Audio
Realtek ALC888 High Definition Audio chip
LAN
Realtek RTL8111CP PCIe GbE chip
Realtek RTL8111CP PCIe GbE chip
I/O Controller Chips
SMSC3114 Super I/O chip
Expansion
PCIe
One PCIe x1 slot
One Mini PCIe slot
I/O Interface Connectors
Audio Connectors
Two external audio jacks (microphone in, line out)
Display port
One VGA
One dual-channel 18/24 bit LVDS (LVDS to TTL optional)
Keyboard/Mouse
One dual PS/2 port
LPT
One parallel port
Serial Ports
Four serial ports
USB 2.0/1.1 ports
Four external USB ports
One MiniUSB port
Storage
Serial ATA
Two SATA connectors directly through Q7 connector
One SATA connector through IDE-to-SATA from CPU
module
Environmental and Power Specifications
Power Supply
Page 24
ATX supported
IQ7 Design Guide
Specification
IQ7 Design Guide
Operating temperature
-20ºC ~ 70ºC (requires cooler and silicone heat sink paste)
Humidity
0% ~ 95% (non-condensing)
Physical Specifications
Dimensions
170 mm x 170 mm
Weight GW/NW
700 g x 350 g
Table 3-1: Technical Specifications
Page 25
IQ7 Design Guide
Chapter
4
4 IQ7-DB-MITX
Connector Pinouts
Page 26
IQ7 Design Guide
4.1 Peripheral Interface Connectors
Section 4.1.2 shows peripheral interface connector locations. Section 4.1.2 lists all the
peripheral interface connectors seen in Section 4.1.2.
4.1.1 Layout
Figure 2-1 shows the on-board peripheral connectors, rear panel peripheral connectors
5
and on-board jumpers.
Figure 4-1: Connector and Jumper Locations
Page 27
IQ7 Design Guide
4.1.2 Peripheral Interface Connectors
Table 2-1 shows a list of the peripheral interface connectors on the IQ7-DB-MITX.
5
Detailed descriptions of these connectors can be found below.
Connector
Type
Label
ATX power connector, system
20-pin ATX
PWR1
Backlight inverter connector
5-pin box header
INVERTER1
CompactFlash® connector
CF slot
CF1
Digital I/O
10-pin header
DIO1
Fan connector
3-pin wafer
FAN2
Front panel connector
14-pin header
F_PANEL1
IDE connector
44-pin
CN30
IDE (CPU module to baseboard)
Flat cable
CN6
LVDS connector
30-pin crimp
CN7
LVDS connector
40-pin crimp
CN16
Mini USB port
Mini-USB
USB_CLIENT
PCIe x1 expansion card slot
PCIe x1 slot
PCIE1
PCIe Mini card slot
PCIe Mini
CN2
Power button
Button
SW2
QSeven connector
QSeven
J1
Reset button
Button
SW1
SATA connectors
SATA
S_ATA1, S_ATA2,
S_ATA3
SATA power
4-pin box header
CN17, CN21, CN23
Serial ports
10-pin box header
COM1, COM2,
COM3
USB connector
8-pin header
Table 4-1: Peripheral Interface Connectors
Page 28
USB5
IQ7 Design Guide
4.1.3 External Interface Panel Connectors
Table 4-2 lists the rear panel connectors on the IQ7-DB-MITX. Detailed descriptions of
5
these connectors can be found in Section 2.1.
Connector
Type
Label
Audio connectors
Audio jacks
AUDIO1
Keyboard and mouse connectors
Dual PS/2
CN9
LAN Connector
RJ-45
LAN_USB1
LAN_USB2
RS-232 serial port connector
D-sub 9-pin male
COM1
USB 2.0 ports
Dual USB ports
LAN_USB1
LAN_USB2
VGA port connector
15-pin female VGA
CON1
Table 4-2: Rear Panel Connectors
4.2 Internal Peripheral Connectors
Internal peripheral connectors are found on the motherboard and are only accessible
when the motherboard is outside of the chassis. This section has complete descriptions of
all the internal, peripheral connectors on the IQ7-DB-MITX.
4.2.1 ATX Power Connector
CN Label:
PWR1
CN Type:
20-pin ATX (2x10)
CN Location:
See Figure 2-3
CN Pinouts:
See Table 2-3
5
5
The ATX connector is connected to an external ATX power supply. Power is provided to
the system, from the power supply through this connector.
Page 29
IQ7 Design Guide
Figure 4-2: ATX Power Connector Pinout Locations
Pin
Description
Pin
Description
1
+3.3 V
13
+3.3 V
2
+3.3 V
14
-12 V
3
GND
15
GND
4
+5 V
16
PS-ON
5
GND
17
GND
6
+5 V
18
GND
7
GND
19
GND
8
NC
20
NC
9
+VCC5SB
21
+5 V
10
+12 V
22
+5 V
Table 4-3: ATX Power Connector Pinouts
4.2.2 Backlight Inverter Connector
CN Label:
INVERTER1
CN Type:
5-pin box header
CN Location:
See Figure 4-3
CN Pinouts:
See Table 4-4
Provides power for the LCD backlight.
Page 30
IQ7 Design Guide
Figure 4-3: Backlight Inverter Connector
Pin
Description
1
BRIGHTNESS
2
GND
3
12 V
4
GND
5
BL_EN
Table 4-4: Backlight Inverter Connector
4.2.3 CompactFlash® Slot
CN Label:
CF1
CN Type:
CompactFlash® card slot
CN Location:
See Figure 4-4
A CompactFlash® Type I/II card can be used in this slot.
Page 31
IQ7 Design Guide
Figure 4-4: CompactFlash® Slot Location
4.2.4 Digital I/O Connector
CN Label:
DIO1
CN Type:
10-pin header
CN Location:
See Figure 4-5
CN Pinouts:
See Table 4-5
The digital I/O connector provides programmable input and output for external devices.
The digital I/O provides 4-bit output and 4-bit input.
Page 32
IQ7 Design Guide
Figure 4-5: Digital I/O Connector Locations
Pin
Description
Pin
Description
1
GND
2
VCC
3
Output 0
4
Output 1
5
Output 2
6
Output 3
7
Input 0
8
Input 1
9
Input 2
10
Input 3
Table 4-5: Digital I/O Connector Pinouts
4.2.5 Fan Connector
CN Label:
FAN2
CN Type:
3-pin header
CN Location:
See Figure 4-6
CN Pinouts:
See Table 4-6
5
5
Connects to a system cooling fan.
Page 33
IQ7 Design Guide
Figure 4-6: Fan Connector Location
Pin
Description
1
Rotation signal
2
+12 V
3
Ground
Table 4-6: Fan Connector Pinouts
4.2.6 Front Panel Connector
CN Label:
F_PANEL1
CN Type:
14-pin header (2x7)
CN Location:
See Figure 4-7
CN Pinouts:
See Table 4-7
5
5
The front panel connector connects to external switches and indicators to monitor and
control the motherboard. These indicators and switches include:
Page 34
ƒ
Power button
ƒ
Reset button
ƒ
Power LED
ƒ
HDD LED
ƒ
Speaker
IQ7 Design Guide
Figure 4-7: Front Panel Connector Pinout Locations
Pin
Description
Pin
Description
1
Power LED+
2
Speaker+
3
N/C
4
N/C
5
Power LED-
6
N/C
7
Power Button+
8
Speaker-
9
Power Button-
10
N/C
11
HDD LED+
12
Reset+
13
HDD LED-
14
Reset-
Table 4-7: Front Panel Connector Pinouts
4.2.7 IDE Connector
CN Label:
CN30
CN Type:
44-pin box header (2x22)
CN Location:
See Figure 4-8
CN Pinouts:
See Table 4-8
Page 35
IQ7 Design Guide
The IDE connector can connect to an IDE hard drive or optical device.
Figure 4-8: IDE Connector Locations
Pin
Description
Pin
Description
1
RESET#
2
GROUND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GROUND
20
N/C
21
IDE DRQ
22
GROUND
23
IOW#
24
GROUND
25
IOR#
26
GROUND
27
IDE CHRDY
28
GROUND
29
IDE DACK
30
GROUND–DEFAULT
31
INTERRUPT
32
N/C
33
SA1
34
N/C
35
SA0
36
SA2
Page 36
IQ7 Design Guide
Pin
Description
Pin
Description
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GROUND
41
VCC
42
VCC
43
GROUND
44
N/C
Table 4-8: IDE Connector Pinouts
4.2.8 IDE (CPU Module to Baseboard)
CN Label:
CN6
CN Type:
40-pin flat cable
CN Location:
See Figure 4-9
CN Pinouts:
See Table 4-9
Connects the IDE channel from the CPU module to the baseboard. IDE is not a supported
I/O interface for the QSeven standard, so the flat cable optionally provides this interface,
which is commonly supported by the Southbridge on the CPU module.
Figure 4-9: CPU Module to Baseboard IDE Connector Location
Pin
Description
Pin
Description
1
Power LED+
2
Speaker+
Page 37
IQ7 Design Guide
Pin
Description
Pin
Description
3
N/C
4
N/C
5
Power LED-
6
N/C
7
Power Button+
8
Speaker-
9
Power Button-
10
N/C
11
HDD LED+
12
Reset+
13
HDD LED-
14
Reset-
Table 4-9: CPU Module to Baseboard IDE Pinouts
4.2.9 LVDS Connector
CN Label:
CN7
CN Type:
30-pin crimp (2x15) DF-13, 180°, P=1.25 mm
CN Location:
See Figure 4-10
CN Pinouts:
See Table 4-10
The LVDS connector is for an LCD panel connected to the board.
Figure 4-10: LVDS Connector Location
Pin
Description
Pin
Description
1
GROUND
2
GROUND
Page 38
IQ7 Design Guide
Pin
Description
Pin
Description
3
A_Y0+
4
A_Y0-
5
A_Y1+
6
A_Y1-
7
A_Y2+
8
A_Y2-
9
A_CLK+
10
A_CLK-
11
N/C
12
N/C
13
GROUND
14
GROUND
15
B_Y0+
16
B_Y0-
17
B_Y1+
18
B_Y1-
19
B_Y2+
20
B_Y2-
21
B_CLK+
22
B_CLK-
23
N/C
24
N/C
25
GROUND
26
GROUND
27
VCC
28
VCC
29
VCC
30
VCC
Table 4-10: LVDS Connector Pinouts
4.2.10 Mini USB Port
CN Label:
USB_CLIENT
CN Type:
Mini-USB
CN Location:
See Figure 4-11
CN Pinouts:
See Table 4-11
Connects to a USB host device.
Page 39
IQ7 Design Guide
Figure 4-11: Mini USB Port Location
Pin
Description
1
+5 V
2
D-
3
D+
4
NC
5
GND
Table 4-11: Mini USB Port Pinouts
4.2.11 PCI Express x1 Slot
CN Label:
PCIE1
CN Type:
PCIe x1 expansion card slot
CN Location:
See Figure 4-12
5
PCIe x1 expansion devices can be inserted into the PCIe x1 slots.
Page 40
IQ7 Design Guide
Figure 4-12: PCIe x1 Connector Location
Pin
Description
Pin
Description
A1
+12v
B1
PRSNT#1
A2
+12v
B2
+12v
A3
RSVD
B3
+12v
A4
GND
B4
GND
A5
SMCLK
B5
JTAG2
A6
SMDAT
B6
JTAG3
A7
GND
B7
JTAG4
A8
+3.3v
B8
JTAG5
A9
JTAG1
B9
+3.3v
A10
3.3 Vaux
B10
+3.3v
A11
WAKE#
B11
PWRGD
A12
RSVD
B12
GND
A13
GND
B13
REFCLK+
A14
HSOp(0)
B14
REFCLK-
A15
HSOn(0)
B15
GND
A16
GND
B16
HSIp(0)
A17
PRSNT#2
B17
HSIn(0)
A18
GND
B18
GND
Table 4-12: PCIe x1 Slot Pinouts
4.2.12 PCIe Mini Card Slot
CN Label:
CN2
Page 41
IQ7 Design Guide
CN Type:
PCIe Mini card slot 52-pin, 90°, P=0.8 mm & 180°, 9.0H
CN Location:
See Figure 4-13
CN Pinouts:
See Table 4-13
5
The PCIe Mini card slot is for installing PCIe Mini expansion cards.
Figure 4-13: PCIe Mini Card Slot Location
Pin
Description
Pin
Description
1
PCIE_WAKE#
2
VCC3
3
N/C
4
GND
5
N/C
6
1.5 V
7
CLKREQ#
8
LFRAME#
9
GND
10
LAD3
11
CLK-
12
LAD2
13
CLK+
14
LAD1
15
GND
16
LAD0
17
PCIRST#
18
GND
19
LPC
20
VCC3
21
GND
22
PCIRST#
23
PERN2
24
3 VDual
25
PERP2
26
GND
27
GND
28
1.5 V
29
GND
30
SMBCLK
31
PETN2
32
SMBDATA
33
PETP2
34
GND
Page 42
IQ7 Design Guide
Pin
Description
Pin
Description
35
GND
36
USBD-
37
N/C
38
USBD+
39
N/C
40
GND
41
N/C
42
N/C
43
N/C
44
RF_LINK#
45
N/C
46
BLUELED#
47
N/C
48
1.5 V
49
N/C
50
GND
51
N/C
52
VCC3
Table 4-13: PCIe Mini Card Slot Pinouts
4.2.13 Power Button
CN Label:
SW2
CN Type:
Button
CN Location:
See Figure 4-14
The power button turns the power on and off.
Figure 4-14: Power Button Location
4.2.14 QSeven Connector
CN Label:
J1
Page 43
IQ7 Design Guide
CN Type:
QSeven connector, MXM, 230-pin, 90°, P=0.5 mm
CN Location:
See Figure 4-15
CN Pinouts:
See Table 4-14
The QSeven CPU module is installed in this slot.
Figure 4-15: QSeven Connector Location
Pin
Description
Pin
Description
1
GND
2
GND
3
GBE_MDI3-
4
GBE_MDI2-
5
GBE_MDI3+
6
GBE_MDI2+
7
GBE_LINK100#
8
GBE_LINK1000#
9
GBE_MDI1-
10
GBE_MDI0-
11
GBE_MDI1+
12
GBE_MDI0+
13
GBE_LINK#
14
GBE_ACT#
15
GBE_CTREF
16
SUS_S5#
17
WAKE#
18
SUS_S3#
19
SUS_STAT#
20
PWRBTN#
21
SLP_BTN#
22
LID_BTN#
23
GND
24
GND
KEY
KEY
KEY
KEY
25
GND
26
PWGIN
27
BATLOW#
28
RSTBTN#
Page 44
IQ7 Design Guide
29
SATA0_TX+
30
SATA1_TX+
31
SATA0_TX-
32
SATA1_TX-
33
SATA_ACT#
34
GND
35
SATA0_RX+
36
SATA1_RX+
37
SATA0_RX-
38
SATA1_RX-
39
GND
40
GND
41
BIOS_DISABLE#
42
SDIO_CLK#
43
SDIO_CD#
44
SDIO_LED
45
SDIO_CMD
46
SDIO_WP
47
SDIO_PWR#
48
SDIO_DAT1
49
SDIO_DAT0
50
SDIO_DAT3
51
SDIO_DAT2
52
SDIO_DAT5
53
SDIO_DAT4
54
SDIO_DAT7
55
SDIO_DAT6
56
RSVD
57
GND
58
GND
59
HDA_SYNC
60
SMB_CLK
61
HDA_RST#
62
SMB_DAT
63
HDA_BITCLK
64
SMB_ALERT#
65
HDA_SDI
66
I2C_CLK
67
HDA_SDO
68
I2C_DAT
69
THRM#
70
WDTRIG#
71
THRMTRIP#
72
WDOUT
73
GND
74
GND
75
USB_P7-
76
USB_P6-
77
USB_P7+
78
USB_P6+
79
USB_6_7_OC#
80
USB_4_5_OC#
81
USB_P5-
82
USB_P4-
83
USB_P5+
84
USB_P4+
85
USB_2_3_OC#
86
USB_0_1_OC#
87
USB_P3-
88
USB_P2-
89
USB_P3+
90
USB_P2+
91
USB_HOST_PRES#
92
USB_HC_SEL
93
USB_P1-
94
USB_P0-
95
USB_P1+
96
USB_P0+
Page 45
IQ7 Design Guide
97
GND
98
GND
99
LVDS_A0+
100
LVDS_B0+
101
LVDS_A0-
102
LVDS_B0-
103
LVDS_A1+
104
LVDS_B1+
105
LVDS_A1-
106
LVDS_B1-
107
LVDS_A2+
108
LVDS_B2+
109
LVDS_A2-
110
LVDS_B2-
111
LVDS_PPEN
112
LVDS_BLEN
113
LVDS_A3+
114
LVDS_B3+
115
LVDS_A3-
116
LVDS_B3-
117
GND
118
GND
119
LVDS_A_CLK+
120
LVDS_B_CLK+
121
LVDS_A_CLK-
122
LVDS_B_CLK-
123
LVDS_BLT_CTRL
124
RSVD
125
LVDS_DID_DAT
126
LVDS_BLC_DAT
127
LVDS_DID_CLK
128
LVDS_BLC_CLK
129
RSVD
130
RSVD
131
SDVO_BCLK+
132
SDVO_INT+
133
SDVO_BCLK-
134
SDVO_INT-
135
GND
136
GND
137
SDVO_GREEN+
138
SDVO_FLDSTALL+
139
SDVO_GREEN-
140
SDVO_FLDSTALL-
141
GND
142
GND
143
SDVO_BLUE+
144
SDVO_TVCLKIN+
145
SDVO_BLUE-
146
SDVO_TVCLKIN-
147
GND
148
GND
149
SDVO_RED+
150
SDVO_CTRL_DAT
151
SDVO_RED-
152
SDVO_CTRL_CLK
153
HDMI_HPD#
154
DP_HPD#
155
PCIE_CLK_REF+
156
PCIE_WAKE#
157
PCIE_CLK_REF-
158
PCIE_RST#
159
GND
160
GND
161
PCIE3_TX+
162
PCIE3_RX+
163
PCIE3_TX-
164
PCIE3_RX-
Page 46
IQ7 Design Guide
165
GND
166
GND
167
PCIE2_TX+
168
PCIE2_RX+
169
PCIE2_TX-
170
PCIE2_RX-
171
EXCD0_PERST#
172
EXCD1_PERST#
173
PCIE1_TX+
174
PCIE1_RX+
175
PCIE1_TX-
176
PCIE1_RX-
177
EXCD0_CPPE#
178
EXCD1_CPPE#
179
PCIE0_TX+
180
PCIE0_RX+
181
PCIE0_TX-
182
PCIE0_RX-
183
GND
184
GND
185
LPC_AD0
186
LPC_AD1
187
LPC_AD2
188
LPC_AD3
189
LPC_CLK
190
LPC_FRAME#
191
SERIRQ
192
LPC_LDRQ#
193
VCC_RTC
194
SPKR
195
FAN_TACHOIN
196
FAN_PWMOUT
197
GND
198
GND
199
RSVD
200
RSVD
201
RSVD
202
RSVD
203
RSVD
204
MFG_NC4
205
VCC_5V_SB
206
VCC_5V_SB
207
MFG_NC0
208
MFG_NC2
209
MFG_NC1
210
MFG_NC3
211
VCC
212
VCC
213
VCC
214
VCC
215
VCC
216
VCC
217
VCC
218
VCC
219
VCC
220
VCC
221
VCC
222
VCC
223
VCC
224
VCC
225
VCC
226
VCC
227
VCC
228
VCC
Page 47
IQ7 Design Guide
229
VCC
230
VCC
Table 4-14: QSeven Connector Pinouts
4.2.15 Reset Button
CN Label:
SW1
CN Type:
Button
CN Location:
See Figure 4-16
Press the reset button to reset the system.
Figure 4-16: Reset Button Location
4.2.16 SATA Drive Connectors
CN Label:
S_ATA1, S_ATA2, S_ATA3
CN Type:
SATA drive connectors
CN Location:
See Figure 4-17
5
The SATA connectors can be connected to SATA peripheral devices like hard drives and
optical drives.
Page 48
IQ7 Design Guide
Figure 4-17: SATA Drive Connector Locations
4.2.17 SATA Power Connectors
CN Label:
CN17, CN21, CN23
CN Type:
4-pin wafer (1x4), 180°, P=2.5 mm
CN Location:
See Figure 4-18
CN Pinouts:
See Table 4-15
The SATA power connectors provide power to connected SATA devices like SATA hard
drives or optical drives.
Figure 4-18: SATA Power Connector Locations
Page 49
IQ7 Design Guide
Pin
Description
1
+5 V
2
GND
3
GND
4
+12 V
Table 4-15: SATA Power Connector Pinouts
4.2.18 SDVO Connector
CN Label:
SDVO1
CN Type:
Flat cable
CN Pinouts:
See Table 4-8
The SDVO connector is an optional extra that can attach to an SDVO graphics card.
Pin
Description
Pin
Description
1
RESET#
2
GROUND
3
DATA 7
4
DATA 8
5
DATA 6
6
DATA 9
7
DATA 5
8
DATA 10
9
DATA 4
10
DATA 11
11
DATA 3
12
DATA 12
13
DATA 2
14
DATA 13
15
DATA 1
16
DATA 14
17
DATA 0
18
DATA 15
19
GROUND
20
N/C
21
IDE DRQ
22
GROUND
23
IOW#
24
GROUND
25
IOR#
26
GROUND
27
IDE CHRDY
28
GROUND
29
IDE DACK
30
GROUND–DEFAULT
31
INTERRUPT
32
N/C
33
SA1
34
N/C
Page 50
IQ7 Design Guide
Pin
Description
Pin
Description
35
SA0
36
SA2
37
HDC CS0#
38
HDC CS1#
39
HDD ACTIVE#
40
GROUND
41
VCC
42
VCC
43
GROUND
44
N/C
Table 4-16: IDE Connector Pinouts
4.2.19 Serial Port Connectors
CN Label:
COM2, COM3, COM4
CN Type:
10-pin box header (2x5), 180°, P=2.5 mm
CN Location:
See Figure 4-19
CN Pinouts:
See Table 4-17
The serial ports provide RS-232 transmission capabilities.
Figure 4-19: Serial Port Connector Locations
Pin
Description
Pin
Description
1
DCD1
2
DSR1
3
RXD1
4
RTS1
Page 51
IQ7 Design Guide
Pin
Description
Pin
Description
5
TXD1
6
CTS1
7
DTR1
8
RI1
9
GND1
10
GND1
Table 4-17: Serial Port Connector Pinouts
4.2.20 TTL Connector
CN Label:
CN16
CN Type:
40-pin crimp (2x20) DF-13, 180°, P=1.25 mm
CN Location:
See Figure 4-20
CN Pinouts:
See Table 4-18
The TTL connector is for an LCD panel connected to the board.
Figure 4-20: TTL Connector Location
Pin
Description
Pin
Description
1
+3.3V
2
+3.3V
3
GND
4
GND
5
+3.3V
6
+3.3V
7
SMB_DAT
8
GND
9
TFT_B0
10
TFT_B1
Page 52
IQ7 Design Guide
Pin
Description
Pin
Description
11
TFT_B2
12
TFT_B3
13
TFT_B4
14
TFT_B5
15
TFT_B6
16
TFT_B7
17
TFT_G0
18
TFT_G1
19
TFT_G2
20
TFT_G3
21
TFT_G4
22
TFT_G5
23
TFT_G6
24
TFT_G7
25
TFT_R0
26
TFT_R1
27
TFT_R2
28
TFT_R3
29
TFT_R4
30
TFT_R5
31
TFT_R6
32
TFT_R7
33
GND
34
GND
35
VOCLK
36
VSYNC
37
VDEN
38
HSYNC
39
SMB_CLK
40
LVDS_BKLT_EN
Table 4-18: TTL Connector Pinouts
4.2.21 USB Connector
CN Label:
USB5
CN Type:
8-pin header (2x4) 180°, P=2.0 mm
CN Location:
See Figure 4-21
CN Pinouts:
See Table 4-19
5
5
The USB header can connect to two USB devices.
Page 53
IQ7 Design Guide
Figure 4-21: USB Connector Locations
Pin
Description
Pin
Description
1
VCC
2
GND
3
DATA-
4
DATA+
5
DATA+
6
DATA-
7
GND
8
VCC
Table 4-19: USB Port Connector Pinouts
Page 54
IQ7 Design Guide
4.3 External Interface Connectors
Figure 4-22 shows the IQ7-DB-MITX motherboard external interface connectors. The
5
IQ7-DB-MITX on-board external interface connectors are shown in Figure 4-22.
Figure 4-22: External Interface Connectors
4.3.1 Audio Connector
CN Label:
AUDIO1
CN Type:
Audio jacks, 14-pin, 90°, P=2.5 mm
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-20
The audio jacks connect to external audio devices.
ƒ
Line Out port (Lime): Connects to a headphone or a speaker.
ƒ
Microphone (Pink): Connects a microphone.
Page 55
IQ7 Design Guide
Figure 4-23: Audio Connector
Pin
Description
Pin
Description
1
Ground
2
LMIC1-L
3
NC
4
NC
5
LMIC1-R
22
LFRONT-L
23
NC
24
NC
25
LFRONT-R
Table 4-20: Audio Connector Pinouts
4.3.2 Ethernet Connector
CN Label:
LAN1_USB01, LAN2_USB23
CN Type:
RJ-45
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-21
5
5
A 10/100/1000 Mb/s connection can be made to a Local Area Network.
Pin
Description
Pin
Description
1
MDIA3-
5
MDIA1+
2
MDIA3+
6
MDIA2+
3
MDIA2-
7
MDIA0-
4
MDIA1-
8
MDIA0+
Table 4-21: Ethernet Connector Pinouts
Page 56
IQ7 Design Guide
Figure 4-24: Ethernet Connector
The RJ-45 Ethernet connector has two status LEDs, one green and one yellow. The green
LED indicates activity on the port and the yellow LED indicates the port is linked.
SPEED LED
LINK LED
Status
Description
Status
Description
GREEN
ON: 100 MB
YELLOW
ON: Linked
OFF: 10 MB
Flashing: Activity
Table 4-22: Connector LEDs
4.3.3 Keyboard and Mouse Connector
CN Label:
KB_MS1
CN Type:
PS/2
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-23 and Figure 4-25
5
5
5
The IQ7-DB-MITX has two PS/2 connectors on the mounting bracket for easy connection
to a PS/2 keyboard and PS/2 mouse.
Page 57
IQ7 Design Guide
Figure 4-25: PS/2 Connector
Pin
Description
Pin
Description
1
KEYBOARD DATA
7
MOUSE DATA
2
NC
8
NC
3
GND
9
GND
4
+5 V
10
+5 V
5
KEYBOARD CLOCK
11
MOUSE DATA
6
NC
12
NC
Table 4-23: PS/2 Connectors
4.3.4 Parallel Port Connector
CN Label:
LPT1
CN Type:
D-SUB 25-pin 90° H=31.6 mm
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-24
The parallel port connects to parallel port device, typically a printer.
Pin
Description
Pin
Description
1
STROBE#
14
AUTO FORM FEED #
2
DATA 0
15
ERROR#
Page 58
IQ7 Design Guide
Pin
Description
Pin
Description
3
DATA 1
16
INITIALIZE
4
DATA 2
17
PRINTER SELECT LN#
5
DATA 3
18
GROUND
6
DATA 4
19
GROUND
7
DATA 5
20
GROUND
8
DATA 6
21
GROUND
9
DATA 7
22
GROUND
10
ACKNOWLEDGE
23
GROUND
11
BUSY
24
GROUND
12
PAPER EMPTY
25
GROUND
13
PRINTER SELECT
Table 4-24: Parallel Port Connector Pinouts
Figure 4-26: Parallel Port Connector Location
4.3.5 Serial Port Connector
CN Label:
COM1
CN Type:
DB-9 connector
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-25 and Figure 4-27
5
5
The RS-232 serial connector provides serial connection in the RS-232 mode.
Pin
Description
1
DCD
2
RXD
3
TXD
Page 59
IQ7 Design Guide
Pin
Description
4
DTR
5
GND
6
DSR
7
RTS
8
CTS
9
RI
10
GND
11
GND
Table 4-25: Serial Port Pinouts
Figure 4-27: Serial Port Pinout Locations
4.3.6 USB Ports
CN Label:
LAN1_USB01, LAN2_USB23, USB4_7
CN Type:
USB Combo ports
CN Location:
See Figure 4-22
CN Pinouts:
See Table 4-26
5
The USB ports attach to standard USB devices.
Pin
Description
1
VCC
2
Data-
3
Data+
Page 60
IQ7 Design Guide
Pin
Description
4
Ground
Table 4-26: USB Connector Pinouts
4.3.7 VGA Connector
CN Label:
CON1
CN Type:
D-sub 15-pin female connector
CN Location:
See Figure 4-22
CN Pinouts:
See Figure 4-28 and Table 4-27
5
5
5
The standard 15-pin female VGA connector connects to a CRT or LCD monitor.
Pin
Description
Pin
Description
Pin
Description
1
RED
6
GROUND
11
NC
2
GREEN
7
GROUND
12
SDA
3
BLUE
8
GROUND
13
HSYNC
4
+5V
9
NC
14
VSYNC
5
GROUND
10
GROUND
15
SCL
Table 4-27: VGA Connector Pinouts
Figure 4-28: VGA Connector
Page 61
IQ7 Design Guide
4.4 Jumper Settings
NOTE:
A jumper is a metal bridge that is used
to close an electrical circuit. It consists
of two metal pins and a small metal clip
(often protected by a plastic cover) that
slides over the pins to connect them.
To CLOSE/SHORT a jumper means
connecting the pins of the jumper with
the plastic clip and to OPEN a jumper means removing the plastic clip
from a jumper.
Before the IQ7 Design Guide is installed in the system, the jumpers must be set in
accordance with the desired configuration. The jumpers on the IQ7 Design Guide are
listed in Table 4-28.
5
Description
Label
Type
AT/ATX mode selection
JP8 & SW5
6-pin header & switch
Clear CMOS
JP6
3-pin header
CompactFlash® Master/Slave
JP4
3-pin header
CompactFlash® voltage
JP3
3-pin header
LAN & PCIe enable/disable
SW3
Switch
TTL voltage selection
J_VLVDS1
3-pin header
SATA & graphics settings
SW4
Switch
TTL enable/disable
SW5
Switch
Table 4-28: Jumpers
Page 62
IQ7 Design Guide
Figure 4–29: Jumpers
4.4.1 AT/ATX Mode Selection
Jumper Label:
JP8 & SW5
Jumper Type:
6-pin header & switch
Jumper Settings:
See Table 4-29 & Table 4-30
Jumper Location:
See Figure 4–29
5
Set both of the jumpers select AT or ATX power mode for the IQ7 Design Guide. AT
power mode limits the system to on/off. ATX allows the system to use various power
saving states and enter a standby state, so the system can be turned on remotely over a
network. The settings on both jumpers should be the same.
JP8
Description
1-2
ATX mode
3-4
AT mode
5-6
No function
Table 4-29: AT/ATX Mode Selection
Page 63
IQ7 Design Guide
SW5
Description
1-On
AT mode
1-Off
ATX mode
Table 4-30: AT/ATX Mode Selection
4.4.2 Clear CMOS Jumper
Jumper Label:
JP8
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-31
Jumper Location:
See Figure 4–29
If the IQ7 Design Guide fails to boot due to improper BIOS settings, the clear CMOS
jumper clears the CMOS data and resets the system BIOS information. To do this, use the
jumper cap to close pins 2 and 3 for a few seconds then reinstall the jumper clip back to
pins 1 and 2.
If the “CMOS Settings Wrong” message is displayed during the boot up process, the fault
may be corrected by pressing the F1 to enter the CMOS Setup menu. Do one of the
following:
ƒ
Enter the correct CMOS setting
ƒ
Load Optimal Defaults
ƒ
Load Failsafe Defaults.
After having done one of the above, save the changes and exit the CMOS Setup menu.
The clear CMOS jumper settings are shown in Table 4-31.
5
Pin
Description
1-2
Keep CMOS Setup
2-3
Clear CMOS Setup
Table 4-31: Clear CMOS Jumper Settings
Page 64
IQ7 Design Guide
4.4.3 CompactFlash® Master/Slave Selection
Jumper Label:
JP4
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-32
Jumper Location:
See Figure 4–29
Sets the CompactFlash® slot as the IDE primary master or primary slave.
Pin
Description
1-2
Slave
2-3
Master
Table 4-32: CompactFlash® Master/Slave Selection
4.4.4 CompactFlash® Voltage Selection
Jumper Label:
JP3
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-33
Jumper Location:
See Figure 4–29
Sets the voltage of the power supplied to the CompactFlash® card.
Pin
Description
1-2
5.0 V
2-3
3.3 V
Table 4-33: CompactFlash® Voltage Selection
4.4.5 LAN & PCIe Enable/Disable
Jumper Label:
SW3
Jumper Type:
4 switches
Jumper Settings:
See Table 4-34
Jumper Location:
See Figure 4–29
Page 65
IQ7 Design Guide
These settings enable and disabled these devices on the IQ7 Design Guide.
SW3
Description
1-On & 2-Off
PCIe x1 slot enabled & LAN2 disabled
1-Off & 2-On
LAN2 enabled & PCIe x1 slot disabled
3-On & 4-Off
LAN1 enabled & PCIe Mini card disabled
3-Off & 4-On
PCIe Mini enabled & LAN1 disabled
Table 4-34: LAN & PCIe Enable/Disable
4.4.6 TTL Voltage Selection
Jumper Label:
J_VLVDS1
Jumper Type:
3-pin header
Jumper Settings:
See Table 4-35
Jumper Location:
See Figure 4–29
Selects the voltage of the LVDS connector.
Pin
Description
1-2
3.3 V
2-3
5.0 V
Table 4-35: LVDS Voltage Selection
4.4.7 SATA & Graphics Settings
Jumper Label:
SW4
Jumper Type:
4 switches
Jumper Settings:
See Table 4-36
Jumper Location:
See Figure 4–29
These settings enable and disabled these devices on the IQ7 Design Guide.
SW4
Description
1–On & 2-Off
SDVO enabled & VGA disabled
1-Off & 2-On
VGA enabled & SDVO disabled
Page 66
IQ7 Design Guide
SW4
Description
3-On
SATA as master
3-Off
SATA as slave
4-On
SATA disable
4-Off
SATA enabled
Table 4-36: LAN & PCIe Enable/Disable
4.4.8 TTL Enabled/Disable
Jumper Label:
SW5
Jumper Type:
Switch
Jumper Settings:
See Table 4-37
Jumper Location:
See Figure 4–29
Disables/enables the TTL connection.
Pin
Description
2-On
TTL disable
2-Off
TTL enable
Table 4-37: TTL Enable/Disable
Page 67
IQ7 Design Guide
Chapter
5
5 Installation
Page 68
IQ7 Design Guide
5.1 Anti-static Precautions
WARNING:
Failure to take ESD precautions during installation may result in
permanent damage to the device and severe injury to the user.
Electrostatic discharge (ESD) can cause serious damage to electronic components. Dry
climates are especially susceptible to ESD. It is therefore critical to strictly adhere to the
following anti-static precautions when any electrical component is handled.
ƒ
Wear an anti-static wristband: - Wearing a simple anti-static wristband can
help to prevent ESD from damaging the board.
ƒ
Self-grounding:- Before handling the board touch any grounded conducting
material. During the time the board is handled, frequently touch any
conducting materials that are connected to the ground.
ƒ
Use an anti-static pad: When configuring, place on an antic-static pad. This
reduces the possibility of ESD damage.
ƒ
Only handle the edges of the PCB:-: When handling the PCB, hold the PCB
by the edges.
5.2 Installation Considerations
NOTE:
The following installation notices and installation considerations should
be read and understood before installation. All installation notices
should be strictly adhered to. Failing to adhere to these precautions
may lead to severe damage of the product and injury to the person
installing the motherboard.
Page 69
IQ7 Design Guide
WARNING:
The installation instructions described in this manual should be
carefully followed in order to prevent damage to the product, its
components and injury to the user.
Before and during the installation please DO the following:
ƒ
Read the user manual:
o
The user manual provides a complete description of the installation
instructions and configuration options.
ƒ
Wear an electrostatic discharge cuff (ESD):
o
Electronic components are easily damaged by ESD. Wearing an ESD cuff
removes ESD from the body and helps prevent ESD damage.
ƒ
Place the product on an antistatic pad:
o
When installing or configuring the motherboard, place it on an antistatic
pad. This helps to prevent potential ESD damage.
ƒ
Turn all power to the product off:
o
When working with the product, make sure that it is disconnected from all
power supplies and that no electricity is being fed into the system.
Before and during installation, DO NOT:
ƒ
DO NOT remove any of the stickers on the PCB board. These stickers are
required for warranty validation.
ƒ
DO NOT use the product before verifying all the cables and power connectors
are properly connected.
ƒ
DO NOT allow screws to come in contact with the PCB circuit, connector pins,
or its components.
Page 70
IQ7 Design Guide
5.3 CPU Module Installation
WARNING:
Only install the QSeven CPU module on a compatible QSeven
baseboard like the IQ7-DB-MITX. Attempting to force another CPU
card to fit can cause permanent damage to the system.
To install the CPU module, refer to Figure 5-1.
6
Page 71
IQ7 Design Guide
Figure 5-1: Installing the QSeven CPU Module
Step 1: Insert the CPU module into the QSeven slot.
Step 2: Press down with the heatsink on top.
Step 3: Tighten the screws to hold down the CPU card and the heatsink.Step 0:
Page 72
IQ7 Design Guide
Chapter
6
6 BIOS
Page 73
IQ7 Design Guide
6.1 Introduction
The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to
certain system settings. This chapter outlines the options that can be changed.
6.1.1 Starting Setup
The AMI BIOS is activated when the computer is turned on. The setup program can be
activated in one of two ways.
1. Press the DELETE key as soon as the system is turned on or
2. Press the DELETE key when the “Press Del to enter SETUP” message
appears on the screen. 0.
If the message disappears before the DELETE key is pressed, restart the computer and try
again.
6.1.2 Using Setup
Use the arrow keys to highlight items, press ENTER to select, use the PageUp and
PageDown keys to change entries, press F1 for help and press ESC to quit. Navigation
keys are shown in.
Key
Function
Up arrow
Move to previous item
Down arrow
Move to next item
Left arrow
Move to the item on the left hand side
Right arrow
Move to the item on the right hand side
Esc key
Main Menu – Quit and not save changes into CMOS
Status Page Setup Menu and Option Page Setup Menu -Exit current page and return to Main Menu
Page Up key
Increase the numeric value or make changes
Page Dn key
Decrease the numeric value or make changes
F1 key
General help, only for Status Page Setup Menu and Option
Page Setup Menu
Page 74
IQ7 Design Guide
Key
Function
F2 /F3 key
Change color from total 16 colors. F2 to select color
forward.
F10 key
Save all the CMOS changes, only for Main Menu
Table 6-1: BIOS Navigation Keys
6.1.3 Getting Help
When F1 is pressed a small help window describing the appropriate keys to use and the
possible selections for the highlighted item appears. To exit the Help Window press ESC or
the F1 key again.
6.1.4 Unable to Reboot After Configuration Changes
If the computer cannot boot after changes to the system configuration is made, CMOS
defaults. Use the jumper described in Chapter 5.
6.1.5 BIOS Menu Bar
The menu bar on top of the BIOS screen has the following main items:
ƒ
Main – Changes the basic system configuration.
ƒ
Advanced – Changes the advanced system settings.
ƒ
PCIPnP – Changes the advanced PCI/PnP Settings
ƒ
Boot – Changes the system boot configuration.
ƒ
Security – Sets User and Supervisor Passwords.
ƒ
Chipset – Changes the chipset settings.
ƒ
Power – Changes power management settings.
ƒ
Exit – Selects exit options and loads default settings
The following sections completely describe the configuration options found in the menu
items at the top of the BIOS screen and listed above.
Page 75
IQ7 Design Guide
6.2 Main
The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered.
The Main menu gives an overview of the basic system information.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
System Overview
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
AMIBIOS
Version
:08.00.15
Build Date :12/18/08
ID:
:B137MR10
Exit
Use [ENTER], [TAB] or
[SHIFT-TAB] to select a
field.
Use [+] or [-] to
configure system time.
Processor
Intel® Atom CPU Z510 @ 1.10 GHz
Speed
:1100MHz
Count
:1
System Memory
Size
:1019MB
System Time
System Time
[14:20:27]
[Tue 05/06/2008]
CMC Lo-Module: 0D2.023x, Hi-Module:0D2.016x
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 1: Main
ƒ
System Overview
The System Overview lists a brief summary of different system components. The fields in
System Overview cannot be changed. The items shown in the system overview include:
ƒ
AMI BIOS: Displays auto-detected BIOS information
o
o
o
ƒ
Page 76
Build Date: Date the current BIOS version was made
ID: Installed BIOS ID
Processor: Displays auto-detected CPU specifications
o
o
o
ƒ
Version: Current BIOS version
Type: Names the currently installed processor
Speed: Lists the processor speed
Count: The number of CPUs on the motherboard
System Memory: Displays the auto-detected system memory.
IQ7 Design Guide
o
Size: Lists memory size
The System Overview field also has two user configurable fields:
ƒ
System Time [xx:xx:xx]
Use the System Time option to set the system time. Manually enter the hours, minutes
and seconds.
ƒ
System Date [xx/xx/xx]
Use the System Date option to set the system date. Manually enter the day, month and
year.
6.3 Advanced
Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices
through the following sub-menus:
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Advanced Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
WARNING: Setting wrong values in below sections may cause
system to malfunction
>
>
>
>
>
>
CPU Configuration
IDE Configuration
SuperIO Configuration
Hardware Health Configuration
Remote Access Configuration
USB Configuration
Exit
Configure CPU
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 2: Advanced
Page 77
IQ7 Design Guide
6.3.1 CPU Configuration
Use the CPU Configuration menu (BIOS Menu 3) to view detailed CPU specifications
and configure the CPU.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit
Configure Advanced CPU Settings
Module Version:3F.14
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Manufacturer :Intel®
Intel® Atom CPU Z510 @ 1.10 GHz
Frequency
:1.10GHz
FSB Speed
:400Hz
Cache L1
Cache L2
:24 KB
:512 KB
Ratio Actual Value:11
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 3: CPU Configuration
The CPU Configuration menu (BIOS Menu 3) lists the following CPU details:
Page 78
ƒ
Manufacturer: Lists the name of the CPU manufacturer
ƒ
Brand String: Lists the brand name of the CPU being used
ƒ
Frequency: Lists the CPU processing speed
ƒ
FSB Speed: Lists the FSB speed
ƒ
Cache L1: Lists the CPU L1 cache size
ƒ
Cache L2: Lists the CPU L2 cache size
ƒ
Ratio actual value is the ratio of the frequency to the clock speed
IQ7 Design Guide
6.3.2 IDE Configuration
Use the IDE Configuration menu (BIOS Menu 4) to change and/or set the configuration
of the IDE devices installed in the system.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
IDE Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Onboard PCI IDE Controller
[Primary]
> Primary IDE Master
> Primary IDE Slave
Exit
Options
Primary
Disabled
: [Not Detected]
: [Not Detected]
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 4: IDE Configuration
ƒ
Onboard PCI IDE Controller [Primary]
Use the Onboard PCI IDE Controller to configure the IDE channel.
ƒ
Î
Primary
Î
Disabled
DEFAULT
IDE drives are enabled
IDE drives disabled
IDE Master and IDE Slave
When entering setup, BIOS auto detects the presence of IDE devices. BIOS displays the
status of the auto detected IDE devices. The following IDE devices are detected and are
shown in the IDE Configuration menu:
ƒ
Primary IDE Master
ƒ
Primary IDE Slave
Page 79
IQ7 Design Guide
6.3.2.1 IDE Master, IDE Slave
Use the IDE Master and IDE Slave configuration menu to view both primary and
secondary IDE device details and configure the IDE devices connected to the system.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Primary IDE Master
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Device
:Not Detected
Type
LBA/Large Mode
Block (Multi-Sector Transfer)
PIO Mode
DMA Mode
S.M.A.R.T.
32Bit Data Transfer
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Auto]
[Enabled]
Exit
Select the type of device
connected to the system
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 5: IDE Master and IDE Slave Configuration
ƒ
Auto-Detected Drive Parameters
The “grayed-out” items in the left frame are IDE disk drive parameters automatically
detected from the firmware of the selected IDE disk drive. The drive parameters are listed
as follows:
ƒ
Device: Lists the device type (e.g. hard disk, CD-ROM etc.)
ƒ
Type: Indicates the type of devices a user can manually select
ƒ
Vendor: Lists the device manufacturer
ƒ
Size: List the storage capacity of the device.
ƒ
LBA Mode: Indicates whether the LBA (Logical Block Addressing) is a method
of addressing data on a disk drive is supported or not.
ƒ
Block Mode: Block mode boosts IDE drive performance by increasing the
amount of data transferred. Only 512 bytes of data can be transferred per
interrupt if block mode is not used. Block mode allows transfers of up to 64 KB
per interrupt.
ƒ
Page 80
PIO Mode: Indicates the PIO mode of the installed device.
IQ7 Design Guide
ƒ
Async DMA: Indicates the highest Asynchronous DMA Mode that is
supported.
ƒ
Ultra DMA: Indicates the highest Synchronous DMA Mode that is supported.
ƒ
S.M.A.R.T.: Indicates whether or not the Self-Monitoring Analysis and
Reporting Technology protocol is supported.
ƒ
ƒ
32Bit Data Transfer: Enables 32-bit data transfer.
Type [Auto]
Use the Type BIOS option select the type of device the AMIBIOS attempts to boot from
after the Power-On Self-Test (POST) is complete.
Î
BIOS is prevented from searching for an IDE disk
Not Installed
drive on the specified channel.
Î
Auto
DEFAULT
The BIOS auto detects the IDE disk drive type
attached to the specified channel. This setting should
be used if an IDE hard disk drive is attached to the
specified channel.
Î
The CD/DVD option specifies that an IDE CD-ROM
CD/DVD
drive is attached to the specified IDE channel. The
BIOS does not attempt to search for other types of
IDE disk drives on the specified channel.
Î
This option specifies an ATAPI Removable Media
ARMD
Device. These include, but are not limited to:
ZIP
LS-120
ƒ
LBA/Large Mode [Auto]
Use the LBA/Large Mode option to disable or enable BIOS to auto detects LBA (Logical
Block Addressing). LBA is a method of addressing data on a disk drive. In LBA mode, the
maximum drive capacity is 137 GB.
Î
Disabled
BIOS is prevented from using the LBA mode control on
the specified channel.
Page 81
IQ7 Design Guide
Î
Auto
DEFAULT
BIOS auto detects the LBA mode control on the specified
channel.
ƒ
Block (Multi Sector Transfer) [Auto]
Use the Block (Multi Sector Transfer) to disable or enable BIOS to auto detect if the
device supports multi-sector transfers.
Î
BIOS is prevented from using Multi-Sector Transfer on the
Disabled
specified channel. The data to and from the device occurs
one sector at a time.
Î
Auto
DEFAULT
BIOS auto detects Multi-Sector Transfer support on the
drive on the specified channel. If supported the data
transfer to and from the device occurs multiple sectors at
a time.
ƒ
PIO Mode [Auto]
Use the PIO Mode option to select the IDE PIO (Programmable I/O) mode program timing
cycles between the IDE drive and the programmable IDE controller. As the PIO mode
increases, the cycle time decreases.
Î
Auto
DEFAULT
BIOS auto detects the PIO mode. Use this value if the IDE disk
drive support cannot be determined.
Î
0
PIO mode 0 selected with a maximum transfer rate of 3.3 MB/s
Î
1
PIO mode 1 selected with a maximum transfer rate of 5.2 MB/s
Î
2
PIO mode 2 selected with a maximum transfer rate of 8.3 MB/s
Î
3
PIO mode 3 selected with a maximum transfer rate of 11.1 MB/s
Î
4
PIO mode 4 selected with a maximum transfer rate of 16.6 MB/s
(This setting generally works with all hard disk drives
manufactured after 1999. For other disk drives, such as IDE
CD-ROM drives, check the specifications of the drive.)
Page 82
IQ7 Design Guide
ƒ
DMA Mode [Auto]
Use the DMA Mode BIOS selection to adjust the DMA mode options.
Î
Auto
DEFAULT
BIOS auto detects the DMA mode. Use this value if the IDE
disk drive support cannot be determined.
Î
SWDMA0
Single Word DMA mode 0, max transfer rate: 2.1 MB/s
Î
SWDMA1
Single Word DMA mode 1, max transfer rate: 4.2 MB/s
Î
SWDMA2
Single Word DMA mode 2, max transfer rate: 8.3 MB/s
Î
MWDMA0
Multi Word DMA mode 0, max transfer rate: 4.2 MB/s
Î
MWDMA1
Multi Word DMA mode 1, max transfer rate: 13.3 MB/s
Î
MWDMA2
Multi Word DMA mode 2, max transfer rate: 16.6 MB/s
Î
UDMA0
Ultra DMA mode 0, max transfer rate: 16.6 MB/s
Î
UDMA1
Ultra DMA mode 1, max transfer rate: 25 MB/s
Î
UDMA2
Ultra DMA mode 2, max transfer rate: 33.3 MB/s
Î
UDMA3
Ultra DMA mode 3, max transfer rate: 44 MB/s (To use this
mode, it is required that an 80-conductor ATA cable is used.)
Î
Ultra DMA mode 4, max transfer rate: 66.6 MB/s (To use this
UDMA4
mode, it is required that an 80-conductor ATA cable is used.)
Î
Ultra DMA mode 5, max transfer rate: 99.9 MB/s (To use this
UDMA5
mode, it is required that an 80-conductor ATA cable is used.)
ƒ
S.M.A.R.T [Auto]
Use the S.M.A.R.T option to auto-detect, disable or enable Self-Monitoring Analysis and
Reporting Technology (SMART) on the drive on the specified channel. S.M.A.R.T predicts
impending drive failures. The S.M.A.R.T BIOS option enables or disables this function.
Î
Auto
Î
Disabled
Prevents BIOS from using the HDD SMART feature.
Î
Enabled
Allows BIOS to use the HDD SMART feature
DEFAULT
BIOS auto detects HDD SMART support.
Page 83
IQ7 Design Guide
ƒ
32Bit Data Transfer [Enabled]
Use the 32Bit Data Transfer BIOS option to enables or disable 32-bit data transfers.
Î
Disabled
Î
Enabled
Prevents the BIOS from using 32-bit data transfers.
Allows BIOS to use 32-bit data transfers on supported
DEFAULT
hard disk drives.
6.3.3 Super IO Configuration
Use the Super IO Configuration menu (BIOS Menu 6) to set or change the
configurations for the FDD controllers, parallel ports and serial ports.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Configure Super I/O Chipset
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Serial Port1 Address
[3F8]
RS-485 Control for SP1
[Disabled]
Serial Port2 Address
[2F8]
RS-485 Control for SP1
[Disabled]
Serial Port3 Address
[3E8]
Serial Port4 Address
[2E8]
Parallel Port Address
[378]
Parallel Port Mode
[Normal]
Parallel Port IRQ
[IRQ7]
Exit
Allows BIOS to select
Serial Port Base
Addresses
ÅÆ Select Screen
↑ ↓
Select Item
Enter Go to SubScreen
F1
General Help
F10
Save and Exit
ESC
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 6: Super IO Configuration
ƒ
Serial Port1 Address [3F8]
Use the Serial Port1 Address option to select the Serial Port 1 base address.
Î Disabled
Î 3F8
No base address is assigned to Serial Port 1
DEFAULT
I/O port address is 3F8
Î 3E8
I/O port address is 3E8
Î 2E8
I/O port address is 2E8
Page 84
IQ7 Design Guide
ƒ
RS-485 Control for SP1 [Disabled]
This feature enables Automatic Send Data Control when using the RS-485
communication protocol. This setting is important for half duplex 2-wire operation and can
lead to data loss if disabled.
ƒ
ƒ
Disabled
ƒ
Enabled
DEFAULT
Serial Port2 Address [2F8]
Use the Serial Port2 Address option to select the Serial Port 2 base address.
Î Disabled
Î 2F8
ƒ
No base address is assigned to Serial Port 2
I/O port address is 3F8
DEFAULT
Î 3E8
I/O port address is 3E8
Î 2E8
I/O port address is 2E8
RS-485 Control for SP2 [Disabled]
This feature enables Automatic Send Data Control when using the RS-485
communication protocol. This setting is important for half duplex 2-wire operation and can
lead to data loss if disabled.
ƒ
ƒ
Disabled
ƒ
Enabled
DEFAULT
Serial Port3 Address [3E8]
Use the Serial Port3 Address option to select the base addresses for serial port 3
Î Disabled
No base address is assigned to serial port 3
Î 3F8
Serial port 3 I/O port address is 3F8
Î 2F8
Serial port 3 I/O port address is 2F8
Î 3E8
Î 2E8
DEFAULT
Serial port 3 I/O port address is 3E8
Serial port 3 I/O port address is 2E8
Page 85
IQ7 Design Guide
ƒ
Serial Port4 Address [2E8]
Use the Serial Port4 IRQ option to select the interrupt address for serial port 4.
Î Disabled
No base address is assigned to serial port 4
Î 3F8
Serial port 4 I/O port address is 3F8
Î 2F8
Serial port 4 I/O port address is 2F8
Î 3E8
Serial port 4 I/O port address is 3E8
Î 2E8
ƒ
DEFAULT
Serial port 4 I/O port address is 2E8
Parallel Port Address [378]
Use the Parallel Port Address option to select the parallel port base address.
Î Disabled
Î 378
ƒ
No base address is assigned to the Parallel Port
DEFAULT
Parallel Port I/O port address is 378
Î 278
Parallel Port I/O port address is 278
Î 3BC
Parallel Port I/O port address is 3BC
Parallel Port Mode [Normal]
Use the Parallel Port Mode option to select the mode the parallel port operates in.
Î Normal
DEFAULT
The normal parallel port mode is the standard mode
for parallel port operation.
Î Bi-directional
Parallel port outputs are 8-bits long. Inputs are
accomplished by reading 4 of the 8 bits on the
status register.
Î EPP
The parallel port operates in the enhanced parallel
port mode (EPP). The EPP mode supports
bi-directional communication between the system
and the parallel port device and the transmission
rates between the two are much faster than the
Normal mode.
Page 86
IQ7 Design Guide
Î ECP+EPP
The
parallel
port
operates
in
the
extended
capabilities port (ECP) mode. The ECP mode
supports bi-directional communication between the
system and the parallel port device and the
transmission rates between the two are much faster
than the Normal mode
The parallel port is also be compatible with EPP
devices described above
ƒ
Parallel Port IRQ [IRQ7]
Use the Parallel Port IRQ selection to set the parallel port interrupt address.
Î IRQ5
Î IRQ7
IRQ5 is assigned as the parallel port interrupt address
DEFAULT
IRQ7 is assigned as the parallel port interrupt address
Page 87
IQ7 Design Guide
6.3.4 Hardware Health Configuration
The Hardware Health Configuration menu (BIOS Menu 7) shows the operating
temperature, fan speeds and system voltages.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Hardware Health Event Monitoring
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
SYS 1 FAN Mode Setting
[Thermal Mode]
TargetTemp Value
[030]
Tolerance Value
[05]
Startup Value
[050]
Stop Value
[50]
StopTime Value
[001]
SYS 1 FAN PWM Control
[255]
CPU Temperature
SYS 1 Temperature
SYS 2 Temperature
:54ºC/129ºF
:44ºC/111ºF
:54ºC/129ºF
SYS 1 FAN Speed
:N/A
Vcore
+3.3V
VBAT
VCC
:0.976
:3.376
:2.861
:5.130
V
V
V
V
SMSC 3114 HARDWARE MONITOR
+1.5V
+5V
:1.497 V
:5.048 V
Exit
Options
Manual Mode
Thermal Mode
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 7: Hardware Health Configuration
ƒ
Mode Setting [Full On Mode]
Use the Mode Setting option to configure the second fan.
Page 88
IQ7 Design Guide
Î Thermal Mode
The fan adjusts its speed using these
settings:
TargetTemp Value
Tolerance Value
Startup Value
Stop Value
StopTime Value
Î Manual Mode
DEFAULT
The fan spins at the set speed, max speed is
at 255, full-off is at 0.
ƒ
TargetTemp [030]
WARNING:
CPU failure can result if this value is set too high
The fan will turn off if the temperature falls below this value.
ƒ
ƒ
Minimum Value: 0°C
ƒ
Maximum Value: 127°C
Tolerance Value [05]
This options sets how fine the jumps in fan speed are. If the setting is low, the fan will
change speed in small increments, if the value is larger it will change speed in big
amounts.
ƒ
Min: 0
ƒ
Max: 15
Page 89
IQ7 Design Guide
ƒ
StartUp Value [050]
WARNING:
CPU failure can result if this value is set too high
This is the initial speed of the fan when it first starts spinning.
ƒ
ƒ
Minimum: 0
ƒ
Maximum: 127
Stop Value [50]
The fan will be turned off when the PWM speed value falls below this setting. When the
fan gets this slow, it will just turn off.
ƒ
ƒ
Minimum: 0
ƒ
Maximum: 255
StopTime Value [001]
Specifies how long it takes for the fan to shut down after it reaches the shut down setting.
This setting is measured in split-seconds (0.1 s).
Page 90
ƒ
Minimum: 0
ƒ
Maximum: 255
IQ7 Design Guide
6.3.5 AHCI Configuration
Use the AHCI Settings menu (BIOS Menu 8) to report on the auto-detection of devices
connected to the onboard SATA drive connectors.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
AHCI Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
AHCI CD/DVD Boot Time out
[15]
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> AHCI Port0 [Not Detected]
> AHCI Port1 [Not Detected]
> AHCI Port2 [Not Detected]
> AHCI Port3 [Not Detected]
> AHCI Port4 [Not Detected]
> AHCI Port5 [Not Detected]
Exit
Some SATA CD/DVD in AHCI
mode need to wait ready
longer
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 8: AHCI Configuration
ƒ
AHCI Port n [Not Detected]
Use the AHCI Port n BIOS option to check what AHCI (Advanced Host Controller
Interface) devices are detected to a specified SATA drive connector. If a device is
detected, selecting the BIOS option, e.g. “AHCI Port 3” opens a new window.
Page 91
IQ7 Design Guide
6.3.5.1 AHCI Port n
Use the AHCI Port n configuration menu (BIOS Menu 9) to configure the drive connected
to SATA connector n.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
AHCI Port0
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Device
:Not Detected
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
SATA Port0
[Auto]
S.M.A.R.T.
[Enabled]
Exit
Select the type of device
connected to the system
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 9: AHCI Port n Configuration Menu
ƒ
SATA Port n [Auto]
Use the SATA Port n option to enable the system to auto-detect the type of drive
connected to SATA drive connector n.
ƒ
S.M.A.R.T [Enabled]
Use the S.M.A.R.T option to enable S.M.A.R.T (Self-Monitoring, Analysis, and Reporting
Technology) on the drive connected to SATA drive connector n.
Î Enabled
DEFAULT
S.M.A.R.T is enabled on the drive connected to SATA
drive connector n on the system
Î Disabled
S.M.A.R.T is disabled on the drive connected to SATA
drive connector n on the system
Page 92
IQ7 Design Guide
6.3.6 Intel AMT Configuration
Use the Intel AMT menu (BIOS Menu 10) to enable the system to be managed through
the Intel® Active Management Technology (AMT) interface.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Configure Intel® AMT Parameters
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Intel® AMT Support
[Disabled]
Exit
Options
Disabled
Enabled
> ME Subsystem Configuration
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 10: Intel AMT Configuration
ƒ
Intel AMT Support
Use the Intel AMT Support option to enable or disable Intel AMT on the system.
Î
Disabled
Î
Enabled
DEFAULT
Intel AMT disabled
Intel AMT enabled
Page 93
IQ7 Design Guide
6.3.6.1 ME Subsystem Configuration
Use the ME Subsystem Configuration menu (BIOS Menu 11) to configure the Intel®
Management Engine (ME) configuration options.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
ME Subsystem Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
BootBlock HECI Message
[Disabled]
HECI Message
[Disabled]
End of Post S5 HECI Message
[Disabled]
ME HECI Configuration
ME-HECI
ME-IDER
ME-KT
[Enabled]
[Disabled]
[Disabled]
Exit
Options
Disabled
Enabled
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 11: ME Subsystem Configuration
ƒ
BootBlock HECI Message
Use the BootBlock HECI Message option to enable or disable boot disk sector that
contains the Intel® AMT Host-Embedded Controller Interface (HECI) message.
ƒ
Î
Disabled
Î
Enabled
DEFAULT
Boot sector disabled
Boot sector enabled
HECI Message [Enabled]
Use the HECI Message option to enable or disable the Intel® AMT Host-Embedded
Controller Interface (HECI) message.
Î
Disabled
Î
Enabled
Page 94
DEFAULT
HECI message disabled
HECI message enabled
IQ7 Design Guide
ƒ
End of Post S5 HECI Message [Enabled]
Use the End of Post S5 HECI Message option to enable or disable the Intel® AMT the
HECI message to wake the system in an S5 sleep state.
ƒ
Î
Disabled
Î
Enabled
DEFAULT
HECI bus cannot rouse system from an S5 state
HECI bus can rouse system from an S5 state
ME-HECI [Enabled]
This option is not user configurable.
ƒ
ME-IDER [Enabled]
Use the ME-IDER option to enable or disable the IDE-Redirection (IDER) protocol to
enable the Intel® AMT enabled product to boot from an OS image, floppy, CD or a DVD
device.
ƒ
Î
Disabled
Î
Enabled
DEFAULT
The IDER protocol is disabled
The IDER protocol is enabled
ME-KT [Enabled]
Use the ME-KT option to enable or disable the Serial Over LAN (SOL) protocol to enable
the Intel® AMT enabled product to redirect the keyboard/text from a local host to a remote
workstation.
Î
Disabled
Î
Enabled
DEFAULT
The SOL protocol is disabled
The SOL protocol is enabled
Page 95
IQ7 Design Guide
6.3.7 Remote Access Configuration
Use the Remote Access Configuration menu (BIOS Menu 12) to configure remote
access parameters. The Remote Access Configuration is an AMIBIOS feature and
allows a remote host running a terminal program to display and configure the BIOS
settings.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit
Configure Remote Access type and parameters
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Remote Access
[Disabled]
Serial port number
Base Address, IRQ
Serial Port Mode
Redirection After BIOS POST
Terminal Type
[COM1]
[3F8H, 4]
[115200 8,n,1]
[Always]
[ANSI]
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 12: Remote Access Configuration
ƒ
Remote Access [Disabled]
Use the Remote Access option to enable or disable access to the remote functionalities
of the system.
Î
Disabled
Î
Enabled
DEFAULT
Remote access is disabled.
Remote access configuration options shown below
appear:
Serial Port Number
Serial Port Mode
Redirection after BIOS POST
Terminal Type
These configuration options are discussed below.
Page 96
IQ7 Design Guide
ƒ
Serial Port Number [COM1]
Use the Serial Port Number option allows to select the serial port used for remote
access.
ƒ
ƒ
COM1
ƒ
COM2
ƒ
COM3
ƒ
COM4
ƒ
COM5
ƒ
COM6
DEFAULT
Base Address, IRQ [3F8h,4]
The Base Address, IRQ option cannot be configured and only shows the interrupt
address of the serial port listed above.
ƒ
Serial Port Mode [115200 8,n,1]
Use the Serial Port Mode option to select baud rate through which the console redirection
is made. The following configuration options are available
ƒ
115200 8,n,1
ƒ
57600 8,n,1
ƒ
38400 8,n,1
ƒ
19200 8,n,1
ƒ
09600 8,n,1
DEFAULT
NOTE:
Identical baud rate setting musts be set on the host (a management
computer running a terminal software) and the slave
ƒ
Redirection After BIOS POST [Always]
Use the Redirection After BIOS POST option to specify when console redirection should
occur.
Page 97
IQ7 Design Guide
Î
Disabled
The console is not redirected after POST
Î
Boot Loader
Redirection is active during POST and during Boot
Loader
Î
Always
DEFAULT
Redirection is always active (Some OSes may not
work if set to Always)
ƒ
Terminal Type [ANSI]
Use the Terminal Type BIOS option to specify the remote terminal type.
Î
ANSI
Î
VT100
The target terminal type is VT100
Î
VT-UTF8
The target terminal type is VT-UTF8
DEFAULT
The target terminal type is ANSI
6.3.8 USB Configuration
Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information
and configure the USB settings.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
USB Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Module Version – 2.24.3-13.4
USB Devices Enabled:
1 Keyboard, 1 Mouse
USB Function
USB 2.0 Controller
Legacy USB Support
USB 2.0 Controller Mode
[Enabled]
[Enabled]
[Enabled]
[HiSpeed]
> USB Mass Storage Device Configuration
Exit
Options
Disabled
8 USB Ports
Enabled
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 13: USB Configuration
Page 98
IQ7 Design Guide
ƒ
Onboard SiS USB1.1 DEVICE [Enabled]
Use the Onboard SiS USB1.1 DEVICE BIOS option to enable or disable the onboard SiS
USB1.1 controller. If disabled, USB1.1 devices cannot be used.
ƒ
Î
Disabled
Î
Enabled
USB 1.1 interface is disabled and cannot be used.
DEFAULT
USB 1.1 interface is enabled and can be used.
Onboard SiS USB2.0 DEVICE [Enabled]
Use the Onboard SiS USB2.0 DEVICE option to enable or disable the onboard SiS
USB2.0 controller. If disabled, USB2.0 devices cannot be used.
ƒ
Î
Disabled
Î
Enabled
USB 2.0 interface is disabled and cannot be used.
DEFAULT
USB 2.0 interface is enabled and can be used.
USB Configuration
The USB Configuration field shows the system USB configuration. The items listed are:
ƒ
ƒ
Module Version: x.xxxxx.xxxxx
USB Devices Enabled
The USB Devices Enabled field lists the USB devices that are enabled on the system
ƒ
USB Functions [Enabled]
Use the USB Functions to enabled and disabled the USB ports.
Î
Disabled
USB ports disabled
Î
USB 8 ports
Only the USB ports on the rear I/O panel are
activated
Î
ƒ
Enabled
DEFAULT
All the USB ports are enabled
USB 2.0 Controller [Enabled]
Use the USB 2.0 Controller BIOS option to enable or disable the USB 2.0 controller
Page 99
IQ7 Design Guide
ƒ
Î
Disabled
Î
Enabled
USB 2.0 controller disabled
DEFAULT
USB 2.0 controller enabled
Legacy USB Support [Enabled]
Use the Legacy USB Support BIOS option to enable USB mouse and USB keyboard
support.
Normally if this option is not enabled, any attached USB mouse or USB keyboard does not
become available until a USB compatible operating system is fully booted with all USB
drivers loaded. When this option is enabled, any attached USB mouse or USB keyboard
can control the system even when there is no USB driver loaded onto the system.
Î
Disabled
Î
Enabled
Î
Auto
Legacy USB support disabled
DEFAULT
Legacy USB support enabled
Legacy USB support disabled if no USB devices are
connected
ƒ
USB2.0 Controller Mode [HiSpeed]
Use the USB2.0 Controller Mode option to set the speed of the USB2.0 controller.
Î
FullSpeed
Î
HiSpeed
Page 100
The controller is capable of operating at 12 Mb/s
DEFAULT
The controller is capable of operating at 480 Mb/s
IQ7 Design Guide
6.3.8.1 USB Mass Storage Device Configuration
Use the USB Mass Storage Device Configuration menu (BIOS Menu 14) to configure
USB mass storage class devices.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit
USB Mass Storage Device Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
USB Mass Storage Reset Delay
[20 Sec]
Device #1
Emulation Type
M-SysT5 Dell Memory Key 5.04
[Auto]
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 14: USB Mass Storage Device Configuration
ƒ
USB Mass Storage Reset Delay [20 Sec]
Use the USB Mass Storage Reset Delay option to set the number of seconds POST
waits for the USB mass storage device after the start unit command.
Î
POST waits 10 seconds for the USB mass storage
10 Sec
device after the start unit command.
Î
20 Sec
DEFAULT
POST waits 20 seconds for the USB mass storage
device after the start unit command.
Î
30 Sec
POST waits 30 seconds for the USB mass storage
device after the start unit command.
Î
40 Sec
POST waits 40 seconds for the USB mass storage
device after the start unit command.
ƒ
Device ##
The Device## field lists the USB devices that are connected to the system.
Page 101
IQ7 Design Guide
ƒ
Emulation Type [Auto]
Use the Emulation Type BIOS option to specify the type of emulation BIOS has to
provide for the USB device.
Î
Auto
Î
Floppy
DEFAULT
BIOS auto-detects the current USB.
The USB device will be emulated as a floppy drive.
The device can be either A: or B: responding to
INT13h calls that return DL = 0 or DL = 1
respectively.
Î
Forced FDD
Allows a hard disk image to be connected as a
floppy image. This option works only for drives
formatted with FAT12, FAT16 or FAT32.
Î
Hard Disk
Allows the USB device to be emulated as hard disk
responding to INT13h calls that return DL values of
80h or above.
Î
CDROM
Assumes the CD-ROM is formatted as bootable
media. All the devices that support block sizes
greater than 512 bytes can only be booted using this
option.
Page 102
IQ7 Design Guide
6.4 PCI/PnP
Use the PCI/PnP menu (BIOS Menu 15) to configure advanced PCI and PnP settings.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Advanced PCI/PnP Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
WARNING: Setting wrong values in below sections
may cause system to malfunction
IRQ3
IRQ4
IRQ5
IRQ7
IRQ9
IRQ10
IRQ11
IRQ14
IRQ15
[Reserved]
[Reserved]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
[Available]
Reserved Memory Size
[Disabled]
Exit
Available: Specified IRQ
is available to be use
the PCI/PnP devices
Reserved: Specified IRQ
is reserved for use by
legacy ISA devices
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 15: PCI/PnP Configuration
ƒ
IRQ# [Available]
Use the IRQ# address to specify what IRQs can be assigned to a particular peripheral
device.
Î
Available
DEFAULT
The specified IRQ is available to be used by PCI/PnP
devices
Î
The specified IRQ is reserved for use by Legacy ISA
Reserved
devices
ƒ
Reserved Memory Size [Disabled]
Use the Reserved Memory Size BIOS option to specify the amount of memory that
should be reserved for legacy ISA devices.
Î
Disabled
DEFAULT
No memory block reserved for legacy ISA devices
Page 103
IQ7 Design Guide
Î
16K
16 KB reserved for legacy ISA devices
Î
32K
32 KB reserved for legacy ISA devices
Î
64K
64 KB reserved for legacy ISA devices
6.5 Boot
Use the Boot menu (BIOS Menu 16) to configure system boot options.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Boot Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> Boot Settings Configuration
>
>
>
>
Boot Device Priority
Hard Disk Drives
CD/DVD Drives
Removable Drives
Exit
Configure settings
during system boot.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 16: Boot
Page 104
IQ7 Design Guide
6.5.1 Boot Settings Configuration
Use the Boot Settings Configuration menu (BIOS Menu 17) to configure advanced
system boot options.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Boot Settings Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Quick Boot
[Enabled]
Quiet Boot
[Enabled]
AddOn ROM Display Mode
[Force BIOS]
Bootup Num-Lock
[On]
Boot from LAN Support
[Disabled]
Exit
Allows BIOS to skip
certain tests while
booting. This will
decrease the time needed
to boot the system.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 17: Boot Settings Configuration
ƒ
Quick Boot [Enabled]
Use the Quick Boot BIOS option to make the computer speed up the boot process.
Î
Disabled
Î
Enabled
No POST procedures are skipped
DEFAULT
Some POST procedures are skipped to decrease
the system boot time
ƒ
Quiet Boot [Disabled]
Use the Quiet Boot BIOS option to select the screen display when the system boots.
Î
Disabled
Î
Enabled
DEFAULT
Normal POST messages displayed
OEM Logo displayed instead of POST messages
Page 105
IQ7 Design Guide
ƒ
AddOn ROM Display Mode [Force BIOS]
Use the AddOn ROM Display Mode option to allow add-on ROM (read-only memory)
messages to be displayed.
Î
Force BIOS
DEFAULT
The system forces third party BIOS to display
during system boot.
Î
The system displays normal information during
Keep Current
system boot.
ƒ
Bootup Num-Lock [On]
Use the Bootup Num-Lock BIOS option to specify if the number lock setting must be
modified during boot up.
Î
Does not enable the keyboard Number Lock automatically. To
Off
use the 10-keys on the keyboard, press the Number Lock key
located on the upper left-hand corner of the 10-key pad. The
Number Lock LED on the keyboard lights up when the Number
Lock is engaged.
Î
On
DEFAULT
Allows the Number Lock on the keyboard to be enabled
automatically when the computer system boots up. This allows
the immediate use of the 10-key numeric keypad located on
the right side of the keyboard. To confirm this, the Number
Lock LED light on the keyboard is lit.
ƒ
Boot From LAN Support [Disabled]
Use the Boot From LAN Support option to enable the Ethernet controller to boot the
system.
Page 106
ƒ
Enabled
ƒ
Disabled
DEFAULT
IQ7 Design Guide
6.5.2 Boot Device Priority
Use the Boot Device Priority menu (BIOS Menu 18) to specify the boot sequence from
the available devices. The drive sequence also depends on the boot sequence in the
individual device section.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Boot Device Priority
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> 1st Boot Device
[1st Boot Device]
> 2nd Boot Device
[2nd Boot Device]
> 3rd Boot Device
[3rd Boot Device]
Exit
Specifies the boot
sequence from the
available devices.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 18: Boot Device Priority Settings
Page 107
IQ7 Design Guide
6.5.3 Hard Disk Drives
Use the Hard Disk Drives menu to specify the boot sequence of the available HDDs.
Only installed hard drives are shown.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Hard Disk Drives
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> 1st Drive
[Hard Drive 1]
> 2nd Drive
[Hard Drive 2]
> 3rd Drive
[Hard Drive 3]
Exit
Specifies the boot
sequence from the
available devices.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 19: Hard Disk Drives
6.5.4 Removable Drives
Use the Removable Drives menu (BIOS Menu 20) to specify the boot sequence of the
removable drives. Only connected drives are shown.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Hard Disk Drives
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> 1st Drive
[Removable Drive 1]
> 2nd Drive
[Removable Drive 2]
> 3rd Drive
[Removable Drive 3]
Exit
Specifies the boot
sequence from the
available devices.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 20: Removable Drives
Page 108
IQ7 Design Guide
6.5.5 CD/DVD Drives
Use the CD/DVD Drives menu to specify the boot sequence of the available CD/DVD
drives. Only connected drives are shown.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Hard Disk Drives
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
> 1st Drive
[CD/DVD 1]
> 2nd Drive
[CD/DVD 2]
> 3rd Drive
[CD/DVD 3]
Exit
Specifies the boot
sequence from the
available devices.
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 21: CD/DVD Drives
6.6 Security
Use the Security menu (BIOS Menu 22) to set system and user passwords.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit
Security Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Supervisor Password
:Not Installed
User Password
:Not Installed
Change Supervisor Password
Change User Password
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 22: Security
Page 109
IQ7 Design Guide
ƒ
Change Supervisor Password
Use the Change Supervisor Password to set or change a supervisor password. The
default for this option is Not Installed. If a supervisor password must be installed, select
this field and enter the password. After the password has been added, Install appears
next to Change Supervisor Password.
ƒ
Change User Password
Use the Change User Password to set or change a user password. The default for this
option is Not Installed. If a user password must be installed, select this field and enter the
password. After the password has been added, Install appears next to Change User
Password.
ƒ
Clear User Password
Use the Clear User Password to clear a user’s password. The default for this option is
Not Installed. If a user password must be cleared, use this option.
ƒ
Boot Sector Virus Protection [Disabled]
Use the Boot Sector Virus Protection to enable or disable boot sector protection.
Î
Disabled
Î
Enabled
Page 110
DEFAULT
Disables the boot sector virus protection
Enables the boot sector virus protection
IQ7 Design Guide
6.7 Chipset
Use the Chipset menu (BIOS Menu 23) to access the Northbridge and Southbridge
configuration menus
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit
Advanced Chipset Settings
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
WARNING: Setting wrong values in below section
may cause system to malfunction.
> Northbridge Configuration
> Southbridge Configuration
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 23: Chipset
6.7.1 Northbridge Configuration
Use the Northbridge Chipset Configuration menu (BIOS Menu 24) to configure the
Northbridge chipset.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Northbridge Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Integrated Graphics Mode Selec [Enabled, 4MB]
Boot Display Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Boot Display Device
[Auto]
Flat Panel Type
[1024x768 18b]
Exit
Select the amount of
system memory used by
the Integrated Graphic
Device
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 24: Northbridge Chipset Configuration
Page 111
IQ7 Design Guide
ƒ
Integrated Graphics Mode Select [Enable, 4 MB]
This setting determines whether the internal graphics device is used, and how much
memory it will use.
ƒ
ƒ
Disable
ƒ
Enable, 1 MB
ƒ
Enable, 4 MB
ƒ
Enable, 8 MB
DEFAULT
Boot Display Device
This option specifies which video device will be used first when booting up. When set to
auto, the system will use whichever device is attached.
ƒ
ƒ
Auto
ƒ
LFP
ƒ
CRT
DEFAULT
Flat Panel Type
This option specifies the resolution of the flat panel display.
Page 112
ƒ
640x480, 18-bit
ƒ
800x480, 18-bit
ƒ
800x600, 18-bit
ƒ
1024x768, 18-bit
ƒ
1280x1024, 36-bit
ƒ
1400x1050, 36-bit
ƒ
1440x900, 36-bit
ƒ
1600x1200, 36-bit
DEFAULT
IQ7 Design Guide
6.7.2 Southbridge Configuration
The Southbridge Configuration menu (BIOS Menu 25) the Southbridge chipset to be
configured.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Southbridge Chipset Configuration
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Audio Controller Codec
[Auto]
USB Client Controller
[Disabled]
Exit
Options
Auto
Disabled
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 25: Southbridge Chipset Configuration
ƒ
Audio Controller Codec [Auto]
This option enables and disables the High Definition Audio controller.
ƒ
Î
Auto
Î
Disabled
DEFAULT
Enabled when there is a connected audio controller
Always disabled
USB Client Controller [Disabled]
This option enables the ability to have an additional USB controller on the baseboard.
Page 113
IQ7 Design Guide
6.8 Exit
Use the Exit menu (BIOS Menu 26) to load default BIOS values, optimal failsafe values
and to save configuration changes.
Main
Advanced
PCIPNP
BIOS SETUP UTILITY
Boot
Security
Chipset
Exit Options
⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯⎯
Save Changes and Exit
Discard Changes and Exit
Discard Changes
Load Optimal Defaults
Load Failsafe Defaults
Exit
Exit system setup after
saving the changes.
F10 key can be used for
this operation
ÅÆ
↑ ↓
Enter
F1
F10
ESC
Select Screen
Select Item
Go to SubScreen
General Help
Save and Exit
Exit
v02.61 ©Copyright 1985-2006, American Megatrends, Inc.
BIOS Menu 26: Exit
ƒ
Save Changes and Exit
Use the Save Changes and Exit option to save the changes made to the BIOS options
and to exit the BIOS configuration setup program.
ƒ
Discard Changes and Exit
Use the Discard Changes and Exit option to exit the BIOS configuration setup program
without saving the changes made to the system.
ƒ
Discard Changes
Use the Discard Changes option to discard the changes and remain in the BIOS
configuration setup program.
ƒ
Load Optimal Defaults
Use the Load Optimal Defaults option to load the optimal default values for each of the
parameters on the Setup menus. F9 key can be used for this operation.
Page 114
IQ7 Design Guide
ƒ
Load Failsafe Defaults
Use the Load Failsafe Defaults option to load failsafe default values for each of the
parameters on the Setup menus. F8 key can be used for this operation.
Page 115
IQ7 Design Guide
Appendix
A
A BIOS Options
Page 116
IQ7 Design Guide
Below is a list of BIOS configuration options in the BIOS chapter.
ƒ
System Overview .................................................................................................................76
ƒ
System Time [xx:xx:xx] .......................................................................................................77
ƒ
System Date [xx/xx/xx] ........................................................................................................77
ƒ
Onboard PCI IDE Controller [Primary]...............................................................................79
ƒ
IDE Master and IDE Slave....................................................................................................79
ƒ
Auto-Detected Drive Parameters........................................................................................80
ƒ
Type [Auto] ...........................................................................................................................81
ƒ
LBA/Large Mode [Auto].......................................................................................................81
ƒ
Block (Multi Sector Transfer) [Auto] ..................................................................................82
ƒ
PIO Mode [Auto]...................................................................................................................82
ƒ
DMA Mode [Auto].................................................................................................................83
ƒ
S.M.A.R.T [Auto]...................................................................................................................83
ƒ
32Bit Data Transfer [Enabled].............................................................................................84
ƒ
Serial Port1 Address [3F8] ..................................................................................................84
ƒ
RS-485 Control for SP1 [Disabled].....................................................................................85
ƒ
Serial Port2 Address [2F8] ..................................................................................................85
ƒ
RS-485 Control for SP2 [Disabled].....................................................................................85
ƒ
Serial Port3 Address [3E8]..................................................................................................85
ƒ
Serial Port4 Address [2E8]..................................................................................................86
ƒ
Parallel Port Address [378] .................................................................................................86
ƒ
Parallel Port Mode [Normal]................................................................................................86
ƒ
Parallel Port IRQ [IRQ7].......................................................................................................87
ƒ
Mode Setting [Full On Mode] ..............................................................................................88
ƒ
TargetTemp [030] .................................................................................................................89
ƒ
Tolerance Value [05] ............................................................................................................89
ƒ
StartUp Value [050] ..............................................................................................................90
ƒ
Stop Value [50] .....................................................................................................................90
ƒ
StopTime Value [001]...........................................................................................................90
ƒ
AHCI Port n [Not Detected] .................................................................................................91
ƒ
SATA Port n [Auto] ..............................................................................................................92
ƒ
S.M.A.R.T [Enabled].............................................................................................................92
ƒ
Intel AMT Support ................................................................................................................93
ƒ
BootBlock HECI Message ...................................................................................................94
Page 117
IQ7 Design Guide
ƒ
HECI Message [Enabled].....................................................................................................94
ƒ
End of Post S5 HECI Message [Enabled] ..........................................................................95
ƒ
ME-HECI [Enabled] ..............................................................................................................95
ƒ
ME-IDER [Enabled] ..............................................................................................................95
ƒ
ME-KT [Enabled] ..................................................................................................................95
ƒ
Remote Access [Disabled]..................................................................................................96
ƒ
Serial Port Number [COM1].................................................................................................97
ƒ
Base Address, IRQ [3F8h,4]................................................................................................97
ƒ
Serial Port Mode [115200 8,n,1]..........................................................................................97
ƒ
Redirection After BIOS POST [Always] .............................................................................97
ƒ
Terminal Type [ANSI]...........................................................................................................98
ƒ
Onboard SiS USB1.1 DEVICE [Enabled]............................................................................99
ƒ
Onboard SiS USB2.0 DEVICE [Enabled]............................................................................99
ƒ
USB Configuration...............................................................................................................99
ƒ
USB Devices Enabled..........................................................................................................99
ƒ
USB Functions [Enabled]....................................................................................................99
ƒ
USB 2.0 Controller [Enabled]..............................................................................................99
ƒ
Legacy USB Support [Enabled]....................................................................................... 100
ƒ
USB2.0 Controller Mode [HiSpeed]................................................................................. 100
ƒ
USB Mass Storage Reset Delay [20 Sec] ........................................................................ 101
ƒ
Device ##............................................................................................................................ 101
ƒ
Emulation Type [Auto]...................................................................................................... 102
ƒ
IRQ# [Available] ................................................................................................................ 103
ƒ
Reserved Memory Size [Disabled] .................................................................................. 103
ƒ
Quick Boot [Enabled] ....................................................................................................... 105
ƒ
Quiet Boot [Disabled] ....................................................................................................... 105
ƒ
AddOn ROM Display Mode [Force BIOS] ....................................................................... 106
ƒ
Bootup Num-Lock [On] .................................................................................................... 106
ƒ
Boot From LAN Support [Disabled] ................................................................................ 106
ƒ
Change Supervisor Password ......................................................................................... 110
ƒ
Change User Password.................................................................................................... 110
ƒ
Clear User Password ........................................................................................................ 110
ƒ
Boot Sector Virus Protection [Disabled] ........................................................................ 110
ƒ
Integrated Graphics Mode Select [Enable, 4 MB].......................................................... 112
ƒ
Boot Display Device ......................................................................................................... 112
Page 118
IQ7 Design Guide
ƒ
Flat Panel Type.................................................................................................................. 112
ƒ
Audio Controller Codec [Auto] ........................................................................................ 113
ƒ
USB Client Controller [Disabled]..................................................................................... 113
ƒ
Save Changes and Exit .................................................................................................... 114
ƒ
Discard Changes and Exit................................................................................................ 114
ƒ
Discard Changes............................................................................................................... 114
ƒ
Load Optimal Defaults...................................................................................................... 114
ƒ
Load Failsafe Defaults...................................................................................................... 115
Page 119
IQ7 Design Guide
Appendix
B
B Terminology
Page 120
IQ7 Design Guide
AC ’97
Audio Codec 97 (AC’97) refers to a codec standard developed by Intel®
in 1997.
ACPI
Advanced Configuration and Power Interface (ACPI) is an OS-directed
configuration, power management, and thermal management interface.
AHCI
Advanced Host Controller Interface (AHCI) is a SATA Host controller
register-level interface.
ATA
The Advanced Technology Attachment (ATA) interface connects storage
devices including hard disks and CD-ROM drives to a computer.
ARMD
An ATAPI Removable Media Device (ARMD) is any ATAPI device that
supports removable media, besides CD and DVD drives.
ASKIR
Amplitude Shift Keyed Infrared (ASKIR) is a form of modulation that
represents a digital signal by varying the amplitude (“volume”) of the
signal. A low amplitude signal represents a binary 0, while a high
amplitude signal represents a binary 1.
BIOS
The Basic Input/Output System (BIOS) is firmware that is first run when
the computer is turned on and can be configured by the end user
CODEC
The Compressor-Decompressor (CODEC) encodes and decodes digital
audio data on the system.
CompactFlash®
CompactFlash® is a solid-state storage device. CompactFlash® devices
use flash memory in a standard size enclosure. Type II is thicker than
Type I, but a Type II slot can support both types.
CMOS
Complimentary metal-oxide-conductor is an integrated circuit used in
chips like static RAM and microprocessors.
COM
COM refers to serial ports. Serial ports offer serial communication to
expansion devices. The serial port on a personal computer is usually a
male DB-9 connector.
DAC
The Digital-to-Analog Converter (DAC) converts digital signals to analog
signals.
DDR
Double Data Rate refers to a data bus transferring data on both the rising
and falling edges of the clock signal.
Page 121
IQ7 Design Guide
DMA
Direct Memory Access (DMA) enables some peripheral devices to
bypass the system processor and communicate directly with the system
memory.
DIMM
Dual Inline Memory Modules are a type of RAM that offer a 64-bit data
bus and have separate electrical contacts on each side of the module.
DIO
The digital inputs and digital outputs are general control signals that
control the on/off circuit of external devices or TTL devices. Data can be
read or written to the selected address to enable the DIO functions.
EHCI
The Enhanced Host Controller Interface (EHCI) specification is a
register-level interface description for USB 2.0 Host Controllers.
EIDE
Enhanced IDE (EIDE) is a newer IDE interface standard that has data
transfer rates between 4.0 MBps and 16.6 MBps.
EIST
Enhanced Intel® SpeedStep Technology (EIST) allows users to modify
the power consumption levels and processor performance through
application software. The application software changes the bus-to-core
frequency ratio and the processor core voltage.
FSB
The Front Side Bus (FSB) is the bi-directional communication channel
between the processor and the Northbridge chipset.
GbE
Gigabit Ethernet (GbE) is an Ethernet version that transfers data at 1.0
Gbps and complies with the IEEE 802.3-2005 standard.
GPIO
General purpose input
HDD
Hard disk drive (HDD) is a type of magnetic, non-volatile computer
storage device that stores digitally encoded data.
ICH
The Input/Ouput Controll Hub (ICH) is an Intel® Southbridge chipset.
IrDA
Infrared Data Association (IrDA) specify infrared data transmission
protocols used to enable electronic devices to wirelessly communicate
with each other.
L1 Cache
The Level 1 Cache (L1 Cache) is a small memory cache built into the
system processor.
L2 Cache
Page 122
The Level 2 Cache (L2 Cache) is an external processor memory cache.
IQ7 Design Guide
LCD
Liquid crystal display (LCD) is a flat, low-power display device that
consists of two polarizing plates with a liquid crystal panel in between.
LVDS
Low-voltage differential signaling (LVDS) is a dual-wire, high-speed
differential electrical signaling system commonly used to connect LCD
displays to a computer.
POST
The Power-on Self Test (POST) is the pre-boot actions the system
performs when the system is turned-on.
RAM
Random Access Memory (RAM) is volatile memory that loses data when
power is lost. RAM has very fast data transfer rates compared to other
storage like hard drives.
SATA
Serial ATA (SATA) is a serial communications bus designed for data
transfers between storage devices and the computer chipsets. The SATA
bus has transfer speeds up to 1.5 Gbps and the SATA II bus has data
transfer speeds of up to 3.0 Gbps.
S.M.A.R.T
Self Monitoring Analysis and Reporting Technology (S.M.A.R.T) refers to
automatic status checking technology implemented on hard disk drives.
UART
Universal Asynchronous Receiver-transmitter (UART) is responsible for
asynchronous communications on the system and manages the system’s
serial communication (COM) ports.
UHCI
The Universal Host Controller Interface (UHCI) specification is a
register-level interface description for USB 1.1 Host Controllers.
USB
The Universal Serial Bus (USB) is an external bus standard for
interfacing devices. USB 1.1 supports 12Mbps data transfer rates and
USB 2.0 supports 480Mbps data transfer rates.
VGA
The Video Graphics Array (VGA) is a graphics display system developed
by IBM.
Page 123
IQ7 Design Guide
Appendix
C
C Hazardous Materials
Disclosure
Page 124
IQ7 Design Guide
C.1 Hazardous Materials Disclosure Table for IPB Products
Certified as RoHS Compliant Under 2002/95/EC Without
Mercury
The details provided in this appendix are to ensure that the product is compliant with the
Peoples Republic of China (China) RoHS standards. The table below acknowledges the
presences of small quantities of certain materials in the product, and is applicable to China
RoHS only.
A label will be placed on each product to indicate the estimated “Environmentally Friendly
Use Period” (EFUP). This is an estimate of the number of years that these substances
would “not leak out or undergo abrupt change.” This product may contain replaceable
sub-assemblies/components which have a shorter EFUP such as batteries and lamps.
These components will be separately marked.
Please refer to the table on the next page.
Page 125
IQ7 Design Guide
Part Name
Toxic or Hazardous Substances and Elements
Lead
Mercury
Cadmium
Hexavalent
Polybrominated
Polybrominated
(Pb)
(Hg)
(Cd)
Chromium
Biphenyls
Diphenyl
(CR(VI))
(PBB)
Ethers
(PBDE)
Housing
X
O
O
O
O
X
Display
X
O
O
O
O
X
Printed Circuit
X
O
O
O
O
X
X
O
O
O
O
O
X
O
O
O
O
X
Fan Assembly
X
O
O
O
O
X
Power Supply
X
O
O
O
O
X
O
O
O
O
O
O
Board
Metal
Fasteners
Cable
Assembly
Assemblies
Battery
O:
This toxic or hazardous substance is contained in all of the homogeneous materials for the part is
below the limit requirement in SJ/T11363-2006
X:
This toxic or hazardous substance is contained in at least one of the homogeneous materials for
this part is above the limit requirement in SJ/T11363-2006
Page 126
IQ7 Design Guide
此附件旨在确保本产品符合中国 RoHS 标准。以下表格标示此产品中某有毒物质的含量符
合中国 RoHS 标准规定的限量要求。
本产品上会附有”环境友好使用期限”的标签,此期限是估算这些物质”不会有泄漏或突变”的
年限。本产品可能包含有较短的环境友好使用期限的可替换元件,像是电池或灯管,这些元
件将会单独标示出来。
部件名称
有毒有害物质或元素
铅
汞
镉
六价铬
多溴联苯
多溴二苯
(Pb)
(Hg)
(Cd)
(CR(VI))
(PBB)
醚
(PBDE)
壳体
X
O
O
O
O
X
显示
X
O
O
O
O
X
印刷电路板
X
O
O
O
O
X
金属螺帽
X
O
O
O
O
O
电缆组装
X
O
O
O
O
X
风扇组装
X
O
O
O
O
X
电力供应组装
X
O
O
O
O
X
电池
O
O
O
O
O
O
O: 表示该有毒有害物质在该部件所有物质材料中的含量均在 SJ/T11363-2006 标准规定的限量要求以下。
X: 表示该有毒有害物质至少在该部件的某一均质材料中的含量超出 SJ/T11363-2006 标准规定的限量要求。
Page 127
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertising