Bang & Olufsen BeoCenter 6–23 Reference Book
Below you will find brief information for BeoCenter 6-23. This television offers advanced operation beyond daily use, including wake-up timers, computer monitor functionality, and timed on/off settings. It also has set-top box operation capabilities and tuning preference settings. The BeoLink system allows for integration with Bang & Olufsen audio systems. The reference book provides access to on-screen menus and an index for quick navigation.
Advertisement
Advertisement
BeoCenter 6–23
Reference book
Tables of contents in the Reference book
The contents of this Reference book is divided into sections. Each particular section starts with its own detailed table of contents provided with page references. Texts in black refers to the current section, whereas the remaining sections are described in general terms and written in grey.
The main sections are:
• Advanced operation
• Tuning and preference settings
• Placement, sockets and connections
• BeoLink system
• On-screen menus
• Index
Advanced operation
This chapter tells you how to operate your television beyond daily use.
It also tells you how to operate a connected set-top box and other connected video equipment.
• Wake-up Timer, 4
• Use your television as a computer monitor, 5
• Set the television to switch itself on and off, 6
• Set-top box operation, 8
Tuning and preference settings, 11
Find out how to set up your television for the first time and tune in programs.
This chapter also contains information about settings for time, date, stand positions, picture and sound.
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television and how to register extra equipment.
BeoLink system, 43
Find out how to connect an audio system to your television and operate an integrated audio/video system. Find out how to make link connections, operate a link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
3
4
Wake-up Timer
You can make the television wake you up in the morning.
The Wake-up Timer is a once-only
Timer, it lasts for one hour. Like an alarm clock, it is disabled once it has been executed. It applies only to the television it has been programmed on.
Once you have made one Wake-up
Timer, the television automatically suggests the time you entered for the latest Wake-up Timer when you enter a new one.
Wake-up Timers can, of course, also be disabled again.
When you have programmed a Wakeup Timer, the television cannot be part of an ordinary Play Timer or
Standby Timer until the Wake-up
Timer has been carried out or disabled.
Enter a Wake-up Timer
WAKE UP TIMER
SOURCE
PROGRAM
START TIME
ON / OFF
TV
21 BBC
07:00
ON store
GO
Check or delete a Wake-up Timer
PLAY TIMER
TIMER ON / OFF
TIMER LIST
TIMER PROGRAMMING
WAKE UP TIMER
OFF
07:00
select
GO
You must choose the source and program number of your Wake-up Timer as well as the start time.
You can call up the settings for the Wake-up
Timer to check the time or to disable the
Wake-up Timer by setting it to OFF.
To enter settings for a Wake-up Timer …
> Press
MENU to bring up the TV SETUP menu and press to highlight PLAY TIMER.
> Press
GO to bring up the PLAY TIMER menu and press to highlight WAKE UP TIMER.
> Press
GO to bring up the WAKE UP TIMER menu.
> Press or to move through the menu items.
> Use the number buttons to enter information or press or to view your choices for each item.
> When you have filled in the required information, press
GO to store your Wake-up
Timer.
> Press
EXIT to exit all menus.
To change settings for a Wake-up Timer or delete it …
> Press MENU to bring up the TV SETUP menu and press to highlight PLAY TIMER.
> Press GO to bring up the PLAY TIMER menu and press to highlight WAKE UP TIMER.
> Press GO to bring up the WAKE UP TIMER menu.
> Press or to move through the menu items.
> Use or to change settings or enter a new time with the number buttons. Change the ON/
OFF setting to OFF if you wish to delete the
Wake-up Timer.
> When you have made your changes, press
GO to store them.
> Press
EXIT to exit all menus.
Use your television as a computer monitor
If you connect your television to a computer, as described on page 37, you can use it as a monitor.
IMPORTANT! If you wish to connect a computer to the television and use the television as a monitor, make sure that you disconnect the television, the computer, and all equipment connected to the computer from the mains before you connect the computer and the television to each other.
When in use, the computer must be connected to a grounded wall outlet as specified in the computer’s setting-up instructions.
Bring up the computer image on the screen
To see the computer picture on the television screen, you must bring it up with Beo4.
To bring up the computer picture …
Press repeatedly until PC appears
LIST
in the Beo4 display PC
Picture adjustments
DVI SETUP
BRIGHTNESS
CONTRAST
COLOUR
31
31
31
Press to bring up the picture
GO
You can then operate the computer as you normally would.
When you have the computer picture on the screen, you must call up the DVI SETUP menu to make adjustments to brightness, contrast and colour.
> Press MENU to bring up the DVI SETUP menu.
> Press or to move between the menu options.
> Press or to adjust settings.
> Press GO to store your settings and exit the menu.
The settings you make in this menu only apply to the PC setup.
5
6
Set the television to switch itself on and off
You can make your television switch itself on and off automatically via the timed play and timed standby functions, if, for example, there is a programme you do not want to miss.
Enter as many as six Timer settings, and bring up an on-screen list of the
Timer settings you have entered.
From this list, you can edit or delete your Timer settings.
If your television is integrated with a
Bang & Olufsen audio system with a
Master Link cable, these systems can perform the timed play or timed standby functions as well.
For your timed settings to be executed correctly, ensure that the built-in clock is set to the correct time. For further information, refer to the chapter ‘Set the time and date’ on page 23.
Before you start … Timed play and timed standby
If you connect a Bang & Olufsen audio or video product to your television with a Master Link cable, you can exclude or include it in timed functions via the Play Timer menu. For example, set the television’s Play Timer to ON and an audio system’s Play Timer to OFF if you wish timed functions to apply only to the television.
To switch on the Play Timer …
> Press MENU to bring up the TV SETUP menu and press to highlight PLAY TIMER.
> Press
GO to bring up the PLAY TIMER menu, and press or to highlight TIMER ON/OFF.
> Press
GO to bring up the TIMER ON/OFF menu.
> Press or to reveal ON.
> Press
GO to store the setting.
For further information about how to switch the
Play Timer on or off for a connected Bang &
Olufsen audio or video product, refer to the Guide enclosed with the product.
You can preset your television to start and stop automatically at the same time and day every week.
To enter settings for timed play or timed standby …
> Press
MENU to bring up the TV SETUP menu and press to highlight PLAY TIMER.
> Press
GO to bring up the PLAY TIMER menu and press to highlight PLAY TIMER
PROGRAMMING.
> Press GO to bring up the PLAY TIMER
PROGRAMMING menu.
> Press or to move through the menu items.
> Use the number buttons to enter information or press or to view your choices for each item.
When DAYS is highlighted, press once to be able to move through the days, and press or
to remove a day you do not want. Press to move to the next day, and press to move back to a previous day. When the weekday(s) you want are displayed, press GO to accept the day(s).
> When you have filled in the required information, press GO to store your Timer settings.
> Press EXIT to exit all menus.
NOTE! If your television is set up in a link room,
Timer programming must be carried out on your main room system.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
TIMER SETUP
OPTIONS
STAND POSITIONS
TIMER ON / OFF
TIMER INDEX
ON
TIMER ON / OFF
TIMER INDEX
PLAY TIMER PROGRAMMING
PLAY TIMER PROGRAMMING
WAKEUP TIMER OFF select
SOURCE
GO
START TIME select
GO
SOURCE
PROGRAM
START TIME
STOP TIME
DAYS
. . .
TIMER PROGRAMMING
TV
18 BBC
15:40
16:40
M . . TF . S store
GO
View, edit or delete a Timer
Bring up an on-screen list of the settings you have entered. From this list, you can edit or delete your Timer settings.
To view, edit or delete your Timer settings …
> Select TIMER INDEX from the TIMER SETUP menu to bring up your list of Timer settings.
The first Timer setting in the list is already highlighted.
> Press or to move the cursor to a Timer setting you wish to edit.
> To edit a setting, press GO and follow the procedure described to the left.
> To be able to delete a selected setting, press the yellow button.
> If you change your mind, press to move the setting back into the list. You can also press
EXIT to exit all menus.
> Press the yellow button a second time to delete the setting.
Abbreviations for days of the week:
M … Monday
T … Tuesday
W … Wednesday
T … Thursday
F … Friday
S … Saturday
S … Sunday
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
TIMER SETUP
OPTIONS
STAND POSITIONS
TIMER ON / OFF
TIMER INDEX
ON
TIMER ON / OFF
TIMER INDEX
PLAY TIMER PROGRAMMING
PLAY TIMER PROGRAMMING
WAKEUP TIMER OFF select
15:40-16:40
BBC
TV 18
M . . TF . .
select
GO
PLAY TIMER INDEX
15:40-16:40
BBC
6:00 - 7:00
ZDF
20:00-22:00
CNN
TV 18
M . . TF . .
TV 3
MTWTF . .
TV 15
MT . . . S .
delete edit
GO
7
8
Set-top box operation
The built-in Set-top Box Controller acts as an interpreter between a settop box of your choice and the Beo4 remote control. When a set-top box is connected, you can use the Beo4 remote control to gain access to the programs and functions offered by your set-top box.
Some functions are immediately available via Beo4 when you switch on the set-top box. Additional functions are available through a
Set-top Box Controller menu that you bring up on the screen.
Set-top Box Controller menu
Some of the buttons on your set-top box remote control are not immediately available on Beo4. To find out which Beo4 buttons activate specific services or functions in your set-top box, bring up the Set-top Box
Controller menu on the screen.
Press to switch on the set-top box
DTV
Press to bring up the Set-top Box
Controller menu
MENU
Press the number button that activates the function you want, or …
1 – 9
… press one of the coloured buttons to activate a function
1
2
3
4
5
GUIDE
MENU
TEXT
INFO
WIDE
3
4
1
2
5
GUIDE
MENU
TEXT
INFO
WIDE
Example of a Set-top Box Controller menu – The
Beo4 buttons are shown to the left on the menu and the set-top box buttons are shown to the right.
Universal Beo4 operation Use the set-top box’s own menu
If you know which Beo4 button activates the function you want, you can activate the function without bringing up the Set-top Box
Controller menu first.
Once you have activated your set-top box, you can operate the set-top box’s own menus, such as the program guide, via Beo4.
While your set-top box is activated …
Press GO and then the number button that activates the function you want
GO
1 – 9
While the set-top box’s own menu is shown …
Moves the cursor up or down
Moves the cursor left or right
Press one of the coloured buttons to activate a function
Press GO and then or to step up or down through programs directly
GO
Press and hold GO to bring up the Program guide or the ‘Now/
Next’ banner on the screen depending on your set-top box
GO
Selects and activates a function
GO
GO
Press GO and then or to step between menu pages or step in program lists
GO
STOP
Exits menus, or returns to a previous menu*
Exits menus, enters or exits different modes, such as radio
EXIT
Use the coloured buttons as indicated in the menus of your set-top box
*Depending on your set-top box, you may have to press EXIT twice instead of STOP to return to a previous menu.
When set-top box is selected as source, press MENU twice to bring up the television’s main menu.
Use a set-top box in a link room
When your set-top box is connected to the television in the main room, you can operate the set-top box from the link room television.
However, the Set-top Box Controller menu cannot be displayed on the television screen in the link room.
Press to switch on the set-top box in the main room
Press one of the coloured buttons to activate a function
DTV
Press GO and then the number button that activates the function you want
GO
1 – 9
9
10
Tuning and preference settings
Find out how to perform the firsttime setup procedure and tune in all available programs automatically. In addition, you can find information about how to edit tuned programs and adjust other available settings, such as time, date, picture and sound.
For information about how to place your television and connect additional video equipment, refer to the chapter ‘Placement, sockets and
connections’ on page 29.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to operate timed play and timed standby functions, and a connected set-top box.
Tuning and preference settings, 11
• First-time setup of your television, 12
• Edit tuned programs, 15
• Re-tune or add programs, 20
• Set positions for the television to turn to, 22
• Set the time and date, 23
• Adjust picture and sound settings, 24
• Choose menu language, 26
• Choose radio display, 27
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television and how to register extra equipment.
BeoLink system, 43
Find out how to connect an audio system to your television and operate an integrated audio/video system. Find out how to make link connections, operate a link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
11
12
First-time setup of your television
The setup procedure described here is activated only when the television is connected to the mains and switched on for the first time.
You must select the menu language, register any extra equipment you have connected, choose radio display, determine the centre position for the motorised stand – if you television is equipped with one – and start the automatic tuning of TV and radio programs.
Select menu language
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA select accept
GO
Register extra equipment before auto-tuning
AV1
AV 2
CONNECTIONS
V. MEM
DVD store
GO
The first time you switch on your television, you must select which language you want all the menus to be displayed in.
Some extra equipment is detected by the television automatically. You can check and confirm the registration of the equipment involved.
The menu language setup appears. If you wish to change the menu language at a later date, you can find the item under OPTIONS in the TV SETUP menu.
> Press
TV to switch on the television. The language menu appears.
> Press or to move between the displayed languages, if necessary.
> Press
GO to store your choice.
When the CONNECTIONS menu appears …
> Press or to step between menu items: AV 1 and AV 2.
> If necessary, press or to select the option that corresponds to what you have connected to the socket.
> Press
GO to store this setup.
Select radio display Store all programs and settings
STYLE
RADIO DISPLAY
MAXIMUM
GERNO VERSI FOLLOW EPIUM
RADIO 3
BBC CLASSIC
BBC National DAB store
GO
AUTO TUNE
CHECK AERIAL CONNECTION
TV
RADIO
start
GO
Before tuning in programs, you are prompted to select the display type you want to appear on the television screen when you select radio as your source.
When you have made your selections, a menu for program tuning automatically appears on the screen.
When the DISPLAY SETUP menu appears …
> Press or to switch between available settings. The chosen display type is shown in the menu as you change settings.
> Press
GO to store your choice.
When the menu for auto tuning appears, the prompt CHECK AERIAL CONNECTION appears to remind you to check that your TV aerial and radio aerial are properly connected.
> Press
GO to start auto tuning. The television tunes in all available programs.
13
14
>> First-time setup of your television
Determine the centre position
If your television is equipped with the optional motorised stand, the STAND
ADJUSTMENT menu appears on the screen.
Once the centre position is determined, select your favourite positions for when the television is switched on and in standby.
STAND ADJUSTMENT
CENTRE POSITION
When the STAND ADJUSTMENT menu appears …
> Press GO to start stand adjustment.
> If the adjustment is interrupted the text
‘ADJUSTMENT FAILED’ appears on the screen.
Remove obstacles preventing the television from turning, and press GO to start adjustment again.
> Once adjustment is complete, the text
‘ADJUSTMENT OK’ appears, followed by the
STAND POSITIONS menu.
> Move between the different stand positions;
VIDEO, AUDIO and STANDBY by means of
and and press
GO to enter the menu.
> To turn the television, press or .
> Press the green button to store each of the positions.
CALIBRATING . . .
For further information about stand positions, refer to the chapter ‘Set positions for the television to turn to’ on page 22.
adjust
GO
Make sure that there is enough room for the television to turn to the right and left.
Edit tuned programs
If automatic tuning of all radio programs results in more than 99 programs, the EDIT RADIO
PROGRAMS menu appears automatically after tuning. You must then move the radio programs you want to a position within 1 and 99 in the list.
You can at any time rearrange the order in which your radio and TV programs appear, just call up the EDIT
RADIO PROGRAMS or EDIT TV
PROGRAMS menus to do so. These menus also allow you to name and delete radio and TV programs.
If the tuned programs require additional editing, such as fine tuning, use the MANUAL TUNING menu.
Move tuned radio programs
Once automatic tuning of programs has been completed, the EDIT RADIO PROGRAMS menu appears automatically and you can move your tuned programs.
> Press to start editing your radio programs.
> Press or to select the program you wish to move.
> Press once move the program out of the list.
> Press or to move the program to the desired program number.
> Press to make the program move back into the list or change places with the program which occupies the desired program number.
> Now, move the program which you changed places with to an empty program number or to a number already occupied and repeat the procedure.
> When you have moved the relevant programs, press STOP to back up through all menus, or press EXIT to exit all menus.
EDIT RADIO PROGRAMS
91 DR P1
92 DR SOFT
93 . . . . . . . .
94 SKYRADIO
95 DR JAZZ
96 SR SOFT
97 . . . . . . . .
98 NRK JAZZ
99 . . . . . . . .
TOO MANY STATIONS!
MOVE WANTED STATIONS UP
TO THE NUMBERED PROGRAM
SLOTS start
EDIT RADIO PROGRAMS
91 DR P1
92 DR SOFT
93 . . . . . . . .
94 SKYRADIO
95 DR JAZZ
96 SR SOFT
97 . . . . . . . .
98 NRK JAZZ
99 . . . . . . . .
THEVOICE
. . . . . . . .
BBC POP
BBC JAZZ
KW5 HITS
. . . . . . . .
. . . . . . . .
. . . . . . . .
move
GULD FM
move delete
EDIT RADIO PROGRAMS
91 DR P1
92 DR SOFT
93 . . . . . . . .
94 GULD FM
95 DR JAZZ
96 SR SOFT
97 . . . . . . . .
98 NRK JAZZ
99 . . . . . . . .
THEVOICE
. . . . . . . .
BBC POP
BBC JAZZ
KW5 HITS
. . . . . . . .
. . . . . . . .
. . . . . . . .
move
SKYRADIO
move delete
Note that all programs placed on program numbers higher than 99 are deleted when you exit this menu.
15
16
>> Edit tuned programs
Move or delete tuned programs
Once the automatic tuning of programs is completed, you can move or delete any tuned
TV or radio programs you do not want.
Move programs …
> Press
> Press
> Press
> Press
TV to switch on the television, or RADIO to switch on the radio.
MENU to bring up the SETUP menu, and press to highlight TUNING.
GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
GO to bring up the EDIT PROGRAMS menu.
> Press or to select the program you wish to move.
> Press once to be able to move the program.
The program is now moved out of the list.
> Press or to move the program to the desired program number.
> Press to make the program move back into the list or change places with the program which occupies the desired program number.
> Now, move the program which you changed places with to an empty program number or to a number already occupied and repeat the procedure.
> When you have moved the relevant programs, press STOP to back up through all menus, or press EXIT to exit all menus.
Delete programs …
> Press TV to switch on the television, or RADIO to switch on the radio.
> Press MENU to bring up the SETUP menu and press to highlight TUNING.
> Press GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
> Press GO to bring up the EDIT PROGRAMS menu.
> Press or to move to the program you wish to delete.
> Press to move the program out of the list.
> Press the yellow button to be able to delete the program – the program is then shown in red.
> Press the yellow button again to finally delete the program, or press twice to move the program back into the list.
> When you have deleted the relevant programs, press
EXIT to exit all menus.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
1 DR1
2 TV2 select
GO select
GO
EDIT TV PROGRAMS
1 DR1
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
8 BBC
. .
. .
17 NRK
18 TV4 more name move
1
EDIT TV PROGRAMS
DR1
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
. .
17 NRK
18 TV4 move move delete
1
EDIT TV PROGRAMS
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
DR1
. .
17 NRK
18 TV4 move delete
Name tuned programs
The EDIT PROGRAMS menu also allows you to name all programs yourself.
Name programs …
> Press
TV to switch on the television, or RADIO to switch on the radio.
> Press
MENU to bring up the SETUP menu, and press to highlight TUNING.
> Press
GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
> Press
GO to bring up the EDIT PROGRAMS menu.
> Press or to select the program you wish to name.
> Press the green button to be able to name the program. The naming menu is now activated.
> Press or to find the individual characters in the name.
> Press to move to the next character. As you move, the television suggests possible names, but you can still use and , or and to enter or edit all the characters in the name you choose.
> Press GO to store the name.
> If necessary, repeat the procedure and name other program numbers.
> When you have named the relevant programs, press GO to accept your edited list, or press
EXIT to exit all menus.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
1 DR1
2 TV2
3 . . .
select
GO select
GO
EDIT TV PROGRAMS
1 DR1
2
3
A
4
5 ZDF
6 RTL7
7 . . . . . . . .
8 BBC
. .
. .
17 NRK
18 TV 4 character next accept
GO
EDIT TV PROGRAMS
1 DR1
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
8 BBC
9 . . . . . . . .
. .
. .
17 NRK
18 TV4 more name move
17
18
>> Edit tuned programs
Adjust tuned TV programs – manual tuning
You can store TV programs on program numbers of their own. Fine tune the program reception, indicate the presence of coded programs and choose appropriate sound types for the individual programs.
If the item SYSTEM appears on the menu, then make sure that the correct broadcast system is displayed before you begin tuning:
B/G … for PAL/SECAM BG
I … for PAL I
L … for SECAM L
M … for NTSC M
D/K … for PAL/SECAM D/K
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight TUNING.
> Press GO to bring up the TV TUNING menu and press to highlight MANUAL TUNING.
> Press GO to bring up the TV MANUAL TUNING menu.
> Press or to move between items on the menu.
> Press or to view your choices for each item.
> If you choose NAME, then press the green button to start the naming procedure. Use or and
to enter the characters in the name you choose.
> To bring up the extra TV MANUAL TUNING menu, move to EXTRA and press GO. Now fine tune if relevant, or select type of sound.
> When you have finished editing, press GO to accept the settings.
> Press GO to store the adjusted program.
> Press EXIT to exit all menus.
If programs are broadcasted with two languages and you want both languages, you can store the program twice, once with each language.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITION
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
SEARCH
FREQUENCY
PROGRAM NUMBER select
GO select
GO
TV MANUAL TUNING
SEARCH
FREQUENCY
. . .
210
PROGRAM NUMBER 1
NAME DR1
EXTRA
start store
GO
TV MANUAL TUNING
FINE TUNE
DECODER
TV SYSTEM
SOUND
0
OFF
B / G
STEREO accept
GO
TV MANUAL TUNING
SEARCH
FREQUENCY
. . .
210
PROGRAM NUMBER 1
NAME DR1
EXTRA
TUNING STORED
Adjust tuned FM or DAB programs – manual tuning
If your television is equipped with the optional DAB module, you can tune in both
FM and DAB radio programs. During first time setup both types of radio programs are tuned in.
RADIO MANUAL TUNING
FM / DAB
SEARCH
FM
92.6
FREQUENCY . . .
PROGRAM NUMBER 10
NAME
FINE TUNE
SOUND
STRUER
0
STEREO
> Press
RADIO to switch on the radio.
> Press MENU to bring up the SETUP menu and press to highlight TUNING.
> Press GO to bring up the RADIO TUNING menu and press to highlight MANUAL TUNING.
> Press GO to bring up the RADIO MANUAL
TUNING menu.
> Press or to move between items on the menu.
> Press or to view your choices for each item.
> When you switch between FM and DAB the menu changes appearance.
> If you choose NAME, then press the green button to start the naming procedure. Use
or and to enter the characters in the name you choose.
> When you have finished editing, press
GO to accept the settings.
> Press
GO to store the adjusted program.
> Press EXIT to exit all menus. store
GO
174.928MHz
5A 5B 5C 5D 6A - - -
Channels
DAB BAND III
239.200MHz
- - - 12A 12B 12C 12D - - - 13F
Ensemble
DR NEWS
DR SOFT
DR ROCK
…
…
…
…
…
DR BOOGIE
DR SPORT
RADIO MANUAL TUNING
FM / DAB
SEARCH
CHANNEL
DAB
. . .
12 C
PROGRAM
DR DAB
DR SOFT
PROGRAM NUMBER 10
NAME DR SOFT store
GO
Digital Audio Broadcast (DAB) providers send program groups called ensembles. A channel contains a single ensemble, and an ensemble typically contains 5–10 programs. Some DAB providers call an ensemble a ‘multiplex’, or call a program a ‘service’.
19
20
Re-tune or add programs
You can make your television find your TV and radio programs for you.
Preset up to 99 different TV and radio programs on program numbers of their own and give each program a distinct name.
You can tune in new programs, for example, if you move – or re-tune previously deleted programs.
When tuning in programs via the
ADD PROGRAM menu, your previously tuned programs are left unchanged. This allows you to keep program names, their order in the TV or radio lists, and any special settings you may have stored for those programs, such as decoder or broadcast system settings.
Re-tune via automatic tuning
You can re-tune all your TV and radio programs by letting the television tune in all the programs automatically.
> Press
TV to switch on the television, or RADIO to switch on the radio.
> Press
MENU to bring up the SETUP menu and press to highlight TUNING.
> Press
GO to bring up the TUNING menu and press to highlight AUTO TUNING.
> Press
GO to bring up the AUTO TUNING menu.
> Press to start auto tuning.
> Once auto tuning is completed, the EDIT
PROGRAMS menu appears. You can then rearrange the program order, delete programs or rename them.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
1 DR1
2 TV2
3 . . .
select
GO select
GO
TV AUTO TUNING
1 . . . . . . . .
DELETES PROGRAM GROUPS start
TV AUTO TUNING
1 DR1
2 TV2
3 . . . . . . . .
EDIT TV PROGRAMS
1 DR1
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
8 BBC
9 . . . . . . . .
. .
. .
17 NRK
18 TV4 more name move
Please note: If you re-tune all your TV and radio programs, all Groups of programs and program settings you have made disappear!
Add new programs
You can add a new program or update a tuned program which, for example, has been moved by the broadcaster.
> Press
TV to switch on the television, or RADIO to switch on the radio.
> Press
MENU to bring up the SETUP menu and press to highlight TUNING.
> Press
GO to bring up the TUNING menu and press to highlight ADD PROGRAM.
> Press
GO to bring up the ADD PROGRAM menu.
> Press to start. New programs are added automatically as they are found.
> When tuning is completed and new programs have been added, the EDIT PROGRAMS menu appears. You can then rearrange the program order, delete programs or rename them. The cursor highlights the first new program of those just added to the list.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
19 . . . . . . . .
20 . . . . . . . .
21 . . . . . . . .
select
GO select
GO
ADD TV PROGRAM
10 . . . . . . . .
11 . . . . . . . .
12 CNN
13 N3
14 . . . . . . . .
15 SAT 1
16 SVT 2
17 NRK
18 TV4
19 . . . . . . . .
start
21
22
Set positions for the television to turn to
If your television is equipped with the optional motorised stand, you can turn it using the Beo4 remote control.
Furthermore, you can program the television to turn automatically to face your favourite viewing position when you switch on the television, turn to a different position when you listen to radio, and turn away to a standby position when you switch it off.
You can also turn your television by hand.
Choose one position for when you switch the television on, one for radio and one for when you switch it off.
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight STAND POSITIONS.
> Press GO to bring up the STAND POSITIONS menu.
> Press GO to determine the VIDEO position.
> Press or to turn the television, and place it according to your viewing position.
> Press
GO to store the position.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
TV ON
TV STANDBY
VIDEO
AUDIO
STANDBY
STAND POSTIONS select
GO
To store a stand position for when the radio is switched on …
> Press to move to AUDIO.
> Press GO to determine the AUDIO position.
> Press or to turn the television, and place it as you wish.
> Press
GO to store the position.
select
GO
To store a stand position for when the television is switched off and in standby …
> Press to move to STANDBY.
> Press GO to determine the STANDBY position.
> Press or to turn the television, and place it as you wish.
> Press
GO to store the position.
> Press EXIT to leave the menus.
NOTE! For information about first-time installation of the motorised stand, refer to the chapter ‘First-
time setup of your television’ on page 12.
Set the time and date
When you preset your television to switch itself on or off at a particular time, or when you preset a timed recording of a programme on a connected video recorder, the clock ensures that these features are switched on and off at the right times.
The simplest way to set the clock is to synchronise it with a tuned TV program’s teletext service via the
CLOCK menu. If you choose to synchronise the clock, this is done with the teletext service offered by the TV program you are currently watching. If a teletext service is not available, you can set the clock manually.
Before synchronising the clock with a tuned program, make sure that the program you are watching offers a teletext service.
To bring up the clock in the display, press LIST repeatedly to display CLOCK* on Beo4, then press GO. To remove the clock again, repeat the procedure.
> Press TV to switch on the television.
> Press
MENU to bring up the TV SETUP menu and press to highlight OPTIONS.
> Press
GO to bring up the OPTIONS menu and press to highlight CLOCK.
> Press
GO to bring up the CLOCK menu.
> Press or to see your choices for each item.
> Press or to move through menu items. It is only necessary to enter the time manually if
SYNCHRONISE is set to NO.
> Press GO to store your clock and calendar options, or …
> … press EXIT to exit all menus without storing.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK
select
GO
TIME
DATE
MONTH select
GO
TIME
DATE
MONTH
YEAR
SYNCHRONISE
SHOW CLOCK
CLOCK
20:00
23
APR
2001
NO
YES store
GO
If the clock is not updated in the transition between summer and winter time, simply select the program with which you originally synchronised the clock, and the clock is updated.
Abbreviations for months
Jan … January Jul … July
Feb … February
Mar … March
Aug … August
Sep … September
Apr … April
May … May
Jun … June
Oct … October
Nov … November
Dec … December
23
*NOTE! In order to display CLOCK on Beo4, you must first add it to the Beo4 list of functions. For further information, refer to the chapter
‘Customise Beo4’ on page 52.
24
Adjust picture and sound settings
Picture and sound settings are preset from the factory to neutral values which suit most viewing and listening situations. However, if you wish, you can adjust these settings to your liking.
Adjust picture brightness, colour or contrast. Sound settings include volume, bass and treble.
Store your picture and sound settings temporarily – until your television is switched off – or store them permanently.
For information about how to change the picture format, refer to the chapter ‘Adjust sound and picture’ on page 8 in the Guide.
Change brightness, colour or contrast
Adjust the picture settings via the PICTURE menu. Temporary settings are cancelled when you switch off the television.
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and press to highlight PICTURE.
> Press GO to bring up the PICTURE menu.
> Press or to move through menu items.
> Press or to adjust the values.
> Press
EXIT to store your settings until you switch off the television, or …
> … press
GO to store your settings permanently.
For video sources using the NTSC signal, a fourth option – Tint (colour shade or nuance) – is available for adjustment.
To temporarily remove the picture from the screen, press LIST repeatedly to display P.MUTE on Beo4, then press GO. To restore the picture again, press any source button, such as TV.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK select
GO
BRIGHTNESS
CONTRAST
COLOUR select
GO
BRIGHTNESS
CONTRAST
COLOUR
TINT
PICTURE
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
store
GO
Change volume, bass or treble
Adjust the sound settings via the
SOUND SETUP menu. Temporary settings are cancelled when you switch off the television.
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and press to highlight SOUND.
> Press GO to bring up the SOUND menu.
> Press or to move through menu items.
> Press or to adjust the values or choose a setting.
> Press EXIT to store your settings until you switch off the television, or …
> … press GO to store your settings permanently.
If you connect loudspeakers or headphones …
The content of the SOUND menu varies according to what you have connected to the television. For further information, refer to the chapter ‘On-screen menus’ on page 54.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK select
GO
VOLUME
BALANCE
BASS select
GO
VOLUME
BALANCE
BASS
TREBLE
LOUDNESS
SOUND SETUP
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
NO store
GO
25
26
Choose menu language
The menu language you choose during the first-time setup of your television can be changed at any time.
Once a menu language is chosen, all menus and display messages are shown in this language.
You can select the language for on-screen menus via the TV SETUP menu. The text on the screen changes as you move from language to language.
> Press TV to switch on the television.
> Press
MENU to bring up the TV SETUP menu and press to highlight OPTIONS.
> Press
GO to bring up the OPTIONS menu and press to highlight MENU LANGUAGE.
> Press
GO to bring up the MENU LANGUAGE menu.
> Use and to move to your language choice.
> Press GO to make your choice.
> Press
STOP to back up through previous menus or press EXIT to exit all menus directly.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK select
GO
DANSK
DEUTSCH
ENGLISH select
GO
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA select accept
GO
Choose radio display
You can change the radio display at any time. Your choice determines what is shown on the screen, when you select radio as your source.
When you change the radio display style in the RADIO DISPLAY menu, a sample of the display style is shown in the menu.
> Press
RADIO to switch on the radio.
> Press MENU to bring up the RADIO SETUP menu and press to highlight TUNING.
> Press GO to bring up the RADIO TUNING menu and press to highlight RADIO DISPLAY.
> Press GO to bring up the RADIO display menu.
> Press or to change the settings.
> Press GO to store your choice.
> Press
STOP to back up through previous menus or press EXIT to exit all menus directly.
RADIO SETUP
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAMS
ADD PROGRAMS
AUTO TUNING
RADIO TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
RADIO DISPLAY
ADJUST DAB AERIAL
DAB DRC select
GO select
GO
STYLE
RADIO DISPLAY
MAXIMUM
GERNO VERSI FOLLOW EPIUM
RADIO 3
BBC CLASSIC
BBC National DAB store
GO
27
28
Placement, sockets and connections
In this chapter, you can find out how to place and connect your television.
It also gives you an overview of the socket panels.
We recommend that you follow the procedure described below when you set up your television:
– Unpack the television
– Consider the appropriate surroundings for your television
– Mount the television on the chosen stand or bracket
– Place the television
– Connect the cables, additional equipment, and speakers
This procedure is described in detail on the following pages.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to operate timed play and timed standby functions, and a connected set-top box.
Tuning and preference settings, 11
Find out how to set up your television for the first time and tune in programs. This chapter also contains information about settings for time, date, stand positions, picture and sound.
Placement, sockets and connections, 29
• Set up your television, 30
• Camera and headphones sockets, 33
• Socket panel, 34
• Connect additional video equipment, 36
BeoLink system, 43
Find out how to connect an audio system to your television and operate an integrated audio/video system. Find out how to make link connections, operate a link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
29
30
Set up your television
For information about how to fasten and run the cables on the rear of the television, refer to page 32.
For further information about the socket panel, refer to page 34.
Handling your television
– Avoid placing your television in direct sunlight or direct artificial light, such as a spotlight, as this may reduce the sensitivity of the remote control receiver. Also if the screen is overheated, black spots may appear in the picture. These spots disappear again, once the television cools down to normal temperature.
– To avoid injury, use Bang & Olufsen stands or brackets only.
– Make sure that the television is set up, placed and connected in accordance with these instructions.
– The television is developed for indoor use in dry, domestic environments only. Use within a temperature range of 10–40°C (50–105°F).
– Do not place any items on top of the television.
– Always place your television on a firm and stable surface.
– Do not attempt to open the television. Leave such operations to qualified service personnel.
If you have a motorised stand, leave enough space around the television to allow it to turn freely. The television can also be turned by hand.
Overview of socket panels
1 Cover for fastening bracket for the optional stand and wall bracket. Pull out at the bottom to remove the cover.
2 Main socket panel. Refer to page 34 for further information.
3
Cover for main socket panel. Pull out at the top and lift to remove.
4 Cover for camera and headphones sockets.
Push in to open, push again to close.
5
Clamp for cables. It is important that the cables are lead through the clamp and tied with a cable tier as the cables can otherwise be tugged free of the sockets. Refer to page 32 for further information.
1
2
3
4
5
Placement options
The television can be placed in several ways, some are illustrated to the right. Please contact a
Bang & Olufsen retailer for further information.
If you mount the television on one of the motorised stands or on the wall bracket, you can tilt the television up and down, as well as turn it left and right. Note, however, that tilting can only be done manually.
While mounting the television on the base, stand or wall bracket, you can use the packaging to support the products. This makes mounting easier.
For further information, refer to the Guide enclosed with these accessories.
a c c c c c c c b
Attaching the speaker cover: Hold up the
speaker cover slightly to the right of the ‘brackets’ a and b. Now slide the cover to the left to let the
‘attach-points’ engage with the corresponding
‘brackets’ (a, b and c) on the television.
To remove the cover; use your thumb to push the cover to the right to disengage it, then lift it out.
31
32
>> Set up your television
Aerial and mains connections
When you set the television up on its own, simply connect the TV aerial to the TV socket and a FM aerial to the socket marked FM and connect the television to the mains as shown to the right.
If your television is equipped with the optional DAB module, you must connect a
DAB aerial also.
When using a DAB aerial …
– Use the DAB AERIAL ADJUSTMENT menu, described on page 57, to find out where to place your aerial. The menu lets you know how strong the DAB signal is.
– Make sure that you hang or mount the aerial vertically.
TV
DAB
FM
A B C
If you are going to connect speakers, an audio system or any other equipment to the television, do not connect it to the mains yet!
The supplied mains cord and plug are specially designed for the television. If you change the plug or in any way damage the mains cord, it will affect the TV picture adversely!
When connections are complete and the cables have been secured as described on this page, switch on the mains. A tiny, red light appears below the screen. The system is in standby mode and ready to be used. If your television is set up on its own, you can now tune in programs as explained in the chapter ‘First-time setup of your
television’ on page 14.
IMPORTANT! All the cables must be fastened to the television using the enclosed cable tier as shown.
When you have made all the connections and fastened the cables, mount the cable cover again.
Your television was designed to be left in standby mode when not in use. Therefore, to facilitate remote control operation, it is essential that you do not disconnect it from the mains. The television can only be switched off completely, if you disconnect it from the mains.
Camera and headphones sockets
You can connect headphones and listen to a programme, or you can connect a Camcorder and watch your home movies on the television. If you have connected a BeoCord V 8000 video tape recorder, you can copy
Camcorder recordings onto a videotape.
Sockets for temporary connections
PHONES
You can connect stereo headphones to the socket marked PHONES. The television speakers are muted when headphones are connected and activated again when the headphones are disconnected.
PHONES
VIDEO
R
L
These sockets are for the connection of a
Camcorder:
VIDEO
For the video signal.
Watch and copy from a Camcorder
If you have connected a video tape recorder, such as a BeoCord V 8000, to your television, and you connect your Camcorder, you can copy Camcorder recordings onto a videotape.
R – L
For audio connection (right and left sound channel respectively).
Watch digital pictures on your television
To watch your camera pictures, connect the camera and switch the television on. The television automatically registers the signal and you can see the still pictures on the screen.
To copy a recording from a Camcorder …
> Connect your Camcorder and start playback on the Camcorder. The television automatically registers the signal and you can see the pictures on the television screen.
> Press RECORD twice to start recording.
If the signal from the camera is switched off …
> Press LIST repeatedly to display CAMERA on
Beo4 and press GO.
Choosing another source or switching off the television during recording from a Camcorder disrupts recording. It is not possible to view TV programs during recording.
In order to display CAMERA on Beo4, you must first add it to the Beo4 list of functions. For further information, refer to the chapter ‘Customise Beo4’ on page 52.
33
34
Socket panel
The socket panel on your television allow you to connect signal input cables as well as a variety of extra equipment, such as a video recorder or a linked Bang & Olufsen music system.
The AV sockets are the primary sockets for connection of extra equipment. Any equipment you connect to these sockets must be registered in the CONNECTIONS menu. For further information, refer to the chapter ’First-time setup of
your television’ on page 12.
You can also connect a computer and use your television as a monitor.
DVI
DVI connection for receiving digital or analogue graphics from an external PC. Supports following resolutions:
60 Hz;
640×480, 800×600, 1024×768, 1366×768.
~
Connections to the mains.
L
Left, line signal (for sound from PC).
Y
Pb
Pr
L
AV3
R
DVI
AV2
STAND
AV1
MASTER LINK
TV
DAB
FM
R
Right, line signal (for sound from PC).
STAND
For connection of a motorised stand.
POWER LINK
IR-
OUT
AV 2 (AV)
21-pin socket for the AV connection of other equipment, such as a DVD player, a set-top box, a second decoder or a game console.
The socket may be used for an AV 2 Expander instead, which gives the opportunity to connect other non-Bang & Olufsen video equipment at the same time.
DAB
Aerial input socket for DAB aerial.
TV
Aerial input socket from your external aerial or cable TV network, or from your main room television if this television is placed in a link room.
AV 1 (AV VMEM)
21-pin socket for the connection of a Bang &
Olufsen video recorder, a set-top box, a decoder or another video tape recorder. You can also connect other types of extra equipment.
FM
Aerial input socket from your FM aerial.
POWER LINK
For connection of external Bang & Olufsen loudspeakers.
MASTER LINK
Socket for connection of a compatible Bang &
Olufsen music system.
The socket is also used for BeoLink distribution of sound throughout the house.
IR out
For a connected set-top box.
Computer connection
Disconnect the television, the computer, and
all equipment connected to the computer from the mains.
Using the appropriate type of cable, connect one end to the DVI or VGA output socket on your computer, and the other end to the DVI socket on the television.
To hear sound from the computer in the television speakers, use the appropriate cable and connect the sound output on the computer to the L – R sockets on the television.
IMPORTANT! If you wish to connect a computer to
the television and use the television as a monitor, make sure that the television, the computer, and all equipment connected to the computer are all disconnected from the mains before you connect the computer and the television to each other.
Reconnect the television, the computer, and all equipment connected to the computer to the mains.
In addition, the computer must be connected to a grounded wall outlet as specified in the computer’s setting-up instructions.
35
36
Connect additional video equipment
This chapter describes how to connect additional video equipment to the television.
A decoder can be connected to the television via the AV 2 socket. If your setup also includes a Bang & Olufsen video recorder, you should connect the decoder to the video recorder.
A set-top box can be connected to any of the AV sockets.
When you connect a Bang & Olufsen video recorder, you must connect it to the AV 1 socket, the television detects the connection automatically.
Make sure that all connected equipment is registered in the
CONNECTIONS menu. For further information, refer to the chapter
‘Register additional video equipment’ on page 40.
Connect a decoder
BeoCenter Primary decoder
Secondary decoder
Disconnect all involved systems from the mains before you connect external equipment.
> Connect the cable from the external aerial to the socket marked TV on the television.
> Connect the decoder to the 21-pin AV 1 socket on the television’s socket panel.
If you wish to connect an RF decoder, connect the external aerial cable to the decoder input socket and then forward the signal or cable to the television’s aerial socket (marked ‘TV IN’).
Tuned programs and decoder detection
In most cases, a connected decoder is registered automatically during tuning. The decoder should automatically detect those programs which require decoding. However, if this is not the case, then adjust the setting via the MANUAL TUNING menu for the program in question. Please refer to the section entitled ‘Adjust tuned TV programs’ in the chapter ‘Edit tuned programs’ on page 18.
Connect a set-top box
Disconnect all involved systems from the mains before you connect external equipment.
BeoCenter Set-top box
> Connect one end of a 21-pin AV cable to the set-top box.
> Run the cable to the AV 1 or AV 2 socket on the back of the television.
> Connect the IR transmitter to the IR OUTPUT socket on the television.
> Fasten the IR transmitter to the IR receiver of the set-top box.
To be able to use the remote control included with your set-top box, do not cover its IR receiver entirely.
Automatic standby …
When you register a set-top box in the
CONNECTIONS menu, you can also select an
‘AUTO STANDBY’ time for your set-top box. This means that you can select if the connected set-top box should switch to standby automatically.
Set-top boxes must be set up in accordance with the documentation enclosed with them.
The options are:
AFTER 0 MIN … The set-top box switches to standby immediately when you select another source.
AFTER 30 MIN … The set-top box switches to standby 30 minutes after you have selected another source*.
AT TV STANDBY … The set-top box switches to standby when you switch the television to standby.
NEVER … The set-top box does not switch to standby automatically.
FOLLOW TV … The set-top box switches on, when you switch your television on and it switches to standby, when you switch your television to standby.
*If you switch the television to standby before the
30 minutes have passed, the set-top box is also switched to standby.
37
38
>> Connect additional video equipment
Connect a Bang & Olufsen recorder
Disconnect all involved systems from the mains before you connect external equipment.
> Connect one end of a 21-pin AV cable to the AV socket on the rear of the recorder.
> Then run the cable to the AV 1 socket on the back of the television.
If the connection between the television and recorder is lost or not connected appropriately, then CONNECTION LOST appears on the screen when you try to program a timed recording.
Restore the connection and try again.
BeoCenter Video recorder
Aerial connection
Use your external aerial connection (or cable TV network connection) and the aerial cable supplied with the video recorder.
BeoCord V 8000
If you connect a BeoCord V 8000 to your television, some of the features of the BeoCord
V 8000 function differently than described in the
BeoCord V 8000 Guide, and some are not available. A supplement for the BeoCord V 8000 is available from you Bang & Olufsen retailer.
> Connect the cable from your external aerial to the signal input socket marked panel of the recorder.
on the rear
> Direct the aerial signal to the television, using the aerial cable supplied with the recorder.
> Plug one end into the socket marked ‘TV’ on the recorder and the other end into the aerial socket marked ‘TV’ on the television’s socket panel.
39
40
Register additional video equipment
If you connect additional video equipment to your television, you must register the equipment in the
CONNECTIONS menu.
When the system is first set up, the equipment connected at that particular moment is detected by the television, and the CONNECTIONS menu appears automatically on the screen. If you connect equipment at a later date, on a permanent basis, then you must register this equipment in the CONNECTIONS menu.
For information about where and how to connect extra equipment, refer to the previous pages and the chapter ‘Socket panel’ on page 34.
What is connected?
Registering the equipment connected to the television enables you to activate it with the
Beo4 remote control.
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu.
CONNECTIONS is highlighted already.
> Press GO to bring up the CONNECTIONS menu.
> Press or to select the AV 1 which corresponds to your setup.
> Press to move to AV 2 and press or to select the AV option which corresponds to your setup.
> Press GO to store this setup.
> Press
STOP to back up through previous menus or press EXIT to exit all menus directly.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK select
GO
MENU LANGUAGE
AV1
AV2 select
GO
AV1
AV 2
CONNECTIONS
V. MEM
NONE store
GO
For further information about the CONNECTIONS menu, refer to the chapter ‘On-screen menus’ on page 54.
If, for some reason, you disconnect the extra equipment and then disconnect the television from the mains, you may have to register the equipment again upon reconnection, even if you have not changed your setup of extra equipment.
STB SETUP
NOKIA 96025
NOKIA 9820T
NOKIA 9850T
PACE DTR730-IM
SKY DIGITAL
SELECTOR
CANALdig DK/S/N
MACAB DCB-101
TPS 96573D
CANAL+ SAT r2
Planet PL 9000
CANALdigital I
ECHOSTAR 9000
CANALdigital E
TV BOX 1000-S
CANALdigital NL
NOKIA D-BOX
NOKIA D-BOX II
HUMAX F1-VACI
TechniBox CAM1 store
GO
If you have connected a set-top box, you will be prompted to select your set-top box from an onscreen list when you select STB in the
CONNECTIONS menu.
41
42
BeoLink system
All your Bang & Olufsen products can be connected in a BeoLink system. A complete BeoLink system enables you to distribute sound and picture from one central source throughout the house.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to operate timed play and timed standby functions, and a connected set-top box.
Tuning and preference settings, 11
Find out how to set up your television for the first time and tune in programs. This chapter also contains information about settings for time, date, stand positions, picture and sound.
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television and how to register extra equipment.
BeoLink system, 43
• Connect and operate an audio system, 44
• Your television in a link room, 48
• Two televisions in the same room, 51
• Customise Beo4, 52
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
43
44
Connect and operate an audio system
If you connect a compatible Bang &
Olufsen audio system to the television using a Master Link cable, you obtain the benefits of an integrated audio/video system.
Play a CD on your audio system using your television speakers, or switch on a TV programme and send the sound to your audio system speakers.
Your AV system can be placed together in one room or in two rooms with the television placed in one room and the audio system with a set of speakers placed in another.
If you disable the internal radio in your television, it cannot be used as source.
Not all Bang & Olufsen audio systems support integration with the television.
Connect a radio
If you connect an audio system to your television, you must enter the BeoLink menu and set up how the radios should be used:
> Press
TV to switch on the television.
> Press MENU to bring up the SETUP menu.
> Press to move to OPTIONS, press
GO to call up the OPTIONS menu.
> Press to move to BEOLINK, press
GO to call up the BEOLINK menu.
> Press or to move between the menu options and press or to change settings.
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK
BEOLINK
MENU LANGUAGE
LINKED RADIO
INTERNAL RADIO select
GO
BEOLINK
LINKED RADIO
INTERNAL RADIO
YES
ENABLE store
GO
Option setting
If your television has been set up in an AV system, you may need to set it to the correct
Option with Beo4. Switch the entire system to standby first.
Option 2 Option 0
Option setting for the television
> While holding the • button on Beo4, press
LIST.
> Let go of both buttons.
> Press
LIST repeatedly to display OPTION? on
Beo4 and press GO.
> Press
LIST repeatedly to display V.OPT on Beo4 and then key in the appropriate number
(
1, 2 or 4).
The television and an audio system set up in one room – all speakers are connected to the television.
Option setting for the audio system
> While holding the • button on Beo4, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press
GO.
> Press LIST repeatedly to display A.OPT on Beo4 and then key in the appropriate number (
0, 1, 2,
5 or 6).
Option 2 Option 2
Option 1
You can choose to set up your television (with or without additional speakers) and the audio system
(with a connected set of speakers) in the same room.
Option 5
Option 1
Option 5
You can choose to set up your audio system in one room, and the television (with or without additional speakers) in another.
If you set up your television in a link room where an audio system is placed, you must set them to
Option 5.
Option 6
45
If you set up your television in a link room without an audio system, you must set it to Option 6.
46
>> Connect and operate an audio system
Use an integrated audio/video system
If you integrate your audio system and your television, you can choose a speaker combination appropriate to the current video or audio program, and also record video sound on the audio system.
Video sound recording
If you listen to sound from your television on your
Bang & Olufsen audio system’s speakers, and your audio system has a tape recorder, you can record television sound on the audio tape recorder. Refer to the Guide enclosed with your audio system for further information.
The setups described on this page illustrate which radio is activated when you have enabled the internal radio and connected a link radio to your television also.
LIST
AV
TV
TV
LIST
AV
TV
To listen to sound from a television source on your audio system speakers without switching on the screen, press LIST repeatedly to display AV* on
Beo4, and then press a source button, such as TV.
To listen to sound from television on your audio system speakers with the screen switched on, press TV, press LIST repeatedly to display AV*, and then press TV again.
LIST
AV
CD
To listen to audio sound on the television speakers, press LIST repeatedly to display AV* on Beo4, and then press an audio source button, such as CD.
*In order to display AV on Beo4, you must first add it to the Beo4 list of functions. For further information, refer to the chapter ‘Customise Beo4’ on page 52.
Your television in a link room with an audio system
If you set up your television in a link room and enable the internal radio, you can choose which radio you want to listen to. However, you can only use the internal radio in your television, if you have enabled it, as described on page 46.
Option 5 Option 5
RADIO
LIST
AV
RADIO
To listen to radio from the audio system, simply press RADIO.
To listen to radio from the built in radio, press LIST repeatedly to display AV* on Beo4, then press
RADIO.
47
48
Your television in a link room
If you have BeoLink installed in your home and you choose to place your television in a link room, you can operate all connected systems through the television.
You must follow the procedure described below when you connect your television for use in a link room:
1 Connect the link room television to the mains
2 Using the Beo4 remote control, program the link room television to
Option 6*
3
Disconnect the link room television from the mains
4
Make the link and aerial connections
5 Reconnect the link room television to the mains.
Option setting
For your entire system to function properly, it is essential that the television in the link room is set to the correct Option before you connect it to the system in the main room!
Main room Link room
To set the link room television to the correct option …
> While holding the • button, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press
GO.
> Press LIST repeatedly to display V.OPT on Beo4 and press
6*.
Option 6*
*If you connect the television for use in a link room where other link systems are already connected, such as speakers, you must set the television to Option 5 instead.
Link frequency
If you change the link frequency in the main room system, make sure that the link frequency in the link room system corresponds to it.
To change the link frequency …
> Press
TV to switch on the television.
> Press MENU to bring up the TV SETUP menu and press to highlight TUNING.
> Press GO to bring up the TV TUNING menu and press to highlight LINK FREQUENCY.
> Press GO to bring up the LINK FREQUENCY menu. FREQUENCY is already highlighted.
> Press or to find the frequency.
> Press
GO to store the setting, or …
> … press EXIT to leave all menus without storing.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSITIONS
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
TV TUNING
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
MANUAL TUNING
LINK FREQUENCY
FREQUENCY select
GO select
GO
LINK FREQUENCY
FREQUENCY 599
search store
GO
49
50
>> Your television in a link room
Link room operation
When you are in the link room, you can operate all connected systems with the Beo4 remote control.
Use a link room source – source type present in both rooms …
Press the button for the source you wish to use
Use sources present only in one of the rooms …
Press the button for the source you wish to use
RADIO
Operate the source as usual
Operate the selected source as usual
Use a main room source – source type present in both rooms …
Press repeatedly on Beo4 until
LINK* is shown in the Beo4 display
LIST
LINK
Listen to stereo sound in your link room …
Usually sound distributed from a main room video source, such as a set-top box, to the link room is transmitted in mono. However, you can select stereo sound:
TV
Press to switch on the television
TV
Press the button for the source you wish to use
TV
Press repeatedly until AV* is shown in the Beo4 display
LIST
AV
Operate the source as usual
Press to activate a source connected to the main room system, such as a set-top box
DTV
While using this function, distribution of other main room sources to other link room systems is not possible.
Main room Link room
*In order to display LINK and AV on Beo4, you must first add them to the Beo4 list of functions.
For further information, refer to the chapter
‘Customise Beo4’ on page 52.
Two televisions in the same room
If you have placed your BeoCenter 6 in a room where you already have a
Bang & Olufsen television, and commands from Beo4 can be received by both televisions, you must change the option setting of
BeoCenter 6. This prevents simultaneous activation of both televisions.
One remote control for both televisions
For your television to function properly, it is essential that the television is set to the correct Option:
BeoCenter 6
Option 4
To set your television for Option 4 …
> While holding the • button on Beo4, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press
GO.
> Press LIST repeatedly to display V.OPT on Beo4 and press
4.
Operate your television in Option 4 …
Normally, you can activate a source, such as
TV, simply by pressing the relevant source button on Beo4. However, when you set your television to Option 4, you must do the following:
LIST
LINK
TV
TV
> Press LIST repeatedly until LINK* is shown in the
Beo4 display.
> Press a source button, such as TV.
*In order to display LINK on Beo4, you must add it to the Beo4 list of functions.
In order to use teletext on a television you have set to Option 4, you must set up Beo4 to ‘VIDEO 3’, but this limits the Beo4 functions that can be used with televisions set to other Options. For further information refer to the chapter ‘Customise Beo4’ on page 52.
51
52
Customise Beo4
The Beo4 buttons give direct remote control of a large number of television functions, and the Beo4 display gives you access to even more functions.
Whenever a source is displayed on
Beo4 (TV, RADIO, etc.), you can press the LIST button and bring up extra functions in the display to help you operate that source, just as if you were calling up extra buttons. You can also switch on extra equipment connected to your television.
You can customise a new Beo4 to suit your television, and change the order in which these extra functions appear when you call them up.
Note that Beo4 contains a list of all of
Bang & Olufsen’s extra audio and video functions, but only those functions supported by the television work when you call them up in the
Beo4 display.
Set up Beo4
The Beo4 is set up for use with BeoCenter 6 from the factory. However, if you buy a new
Beo4 you can set this up for your television also.
Press and hold the standby button down
•
Press to get access to the Beo4 setup function
LIST
Let go of both buttons. ADD? appears in the display
Press repeatedly to display
CONFIG? on Beo4
ADD?
LIST
CONFIG?
GO
Press to be able to select the type of configuration
Press repeatedly to display
VIDEO? on Beo4
LIST
VIDEO?
Press to get access to the video configuration
GO
Press repeatedly to display
VIDEO 2 on Beo4*
LIST
VIDEO 2
Press to store the configuration
GO
STORED appears, indicating that the configuration has been stored. You leave the Beo4 setup function automatically
*If you have set your television to Option 4, select ‘VIDEO 3’.
STORED
Add an extra ‘button’
When you add a new function to the Beo4 list, you can then bring up this new ‘button’ in the Beo4 display.
Press and hold the standby button down
Press to get access to the Beo4 setup function
Let go of both buttons. ADD? appears in the display
•
LIST
ADD?
Press to bring up the list of available ‘buttons’ to add from.
The first ‘button’ appears in the display, it flashes on and off
GO
Press to move forwards or backwards in the list of all extra
‘buttons’
Press to add and place the
‘button’ on its preset position or as the first ‘button’ in the list, or …
GO
… press to insert the ‘button’ at a specific position in the list
1 – 9
ADDED appears, indicating that the ‘button’ has been added.
You leave the Beo4 setup function automatically
ADDED
Move extra ‘buttons’
You can rearrange the order in which the extra ‘buttons’ appear when you press LIST.
Press and hold the standby button down
Press to get access to the Beo4 setup function
•
LIST
Let go of both buttons. ADD? appears in the display
Press repeatedly to display
MOVE? on Beo4
Press to bring up the list of extra
‘buttons’. The first ‘button’ appears in the display
GO
Press to move forwards or backwards in the list of extra
’buttons’
ADD?
LIST
MOVE?
Press to move and place the displayed ‘button’ as the first in the list, or …
GO
… press to move the ‘button’ to a specific position in the list
1 – 9
MOVED appears, indicating that the ‘button’ has been moved.
You leave the Beo4 setup function automatically
MOVED
Remove an extra ‘button’
You can remove any of the extra ‘buttons’ that are available when you press LIST.
Press and hold the standby button down
•
Press to get access to the Beo4 setup function
LIST
Let go of both buttons. ADD? appears in the display
Press repeatedly to display
REMOVE? on Beo4
ADD?
LIST
REMOVE?
Press to bring up the list of extra
‘buttons’. The first ‘button’ appears in the display
GO
Press to move forwards or backwards in the list of extra
’buttons’
Press to remove the ‘button’ shown in the display
REMOVED appears, indicating that the ‘button’ has been removed. You leave the Beo4 setup function automatically
GO
REMOVED
GO
GO 3
3
Add an extra ‘button’ to Beo4, either to the top of the list or to a specific position.
53
Move extra ‘buttons’, either to the top of the list or to a specific position.
54
On-screen menus
In order for you to find your way through the on-screen menus your television offers, this chapter illustrates the overall structure of the menu system.
The chapter also gives you detailed information about the individual menus.
PROGRAM AND STATION GROUPS
TV TUNING
EDIT PROGRAMS
ADD PROGRAMS
AUTO TUNING
MANUAL TUNING
EXTRA
FINE TUNE
DECODER
TV SYSTEM
SOUND
RADIO TUNING
EDIT PROGRAMS
ADD PROGRAMS
AUTO TUNING
MANUAL TUNING
RADIO DISPLAY
ADJUST DAB AERIAL
DAB DRC
LINK FREQUENCY
FREQUENCY
PLAY TIMER
TIMER ON/OFF
TIMER INDEX
PLAY TIMER PROGRAMMING
SOURCE
PROGRAM/STATION
START TIME
STOP TIME
DAYS
WAKE UP TIMER
OPTIONS
CONNECTIONS
AV1
AV2
SOUND
VOLUME
BALANCE
BASS
TREBLE
LOUDNESS NO/YES
PICTURE
BRIGHTNESS
CONTRAST
COLOUR
TINT
CLOCK
TIME
DATE
MONTH
YEAR
SYNCHRONISE
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
STAND POSITIONS
VIDEO
AUDIO
STANDBY
The extended on-screen menu system for the television. The presence of the greyed menu items depends on whether these optional extras are available in your system.
Press MENU on Beo4 to access the main menu.
. . .
. . .
. . .
. . .
GROUP1
. . .
. . .
. . .
PROGRAM GROUPS name move new group create group
GO
EDIT TV PROGRAMS
1 DR1
2 TV2
3 . . . . . . . .
4 EUROSPRT
5 ZDF
6 RTL7
7 . . . . . . . .
8 BBC
9 . . . . . . . .
. .
. .
17 NRK
18 TV4 more name move
ADD TV PROGRAM
10 . . . . . . . .
11 . . . . . . . .
12 CNN
13 N3
14 . . . . . . . .
15 SAT 1
16 SVT 2
17 NRK
18 TV4
19 . . . . . . . .
start
What’s on the PROGRAM GROUPS menu …
You can create program Groups, name them and copy individual TV programs into the Groups.
For further information, refer to the chapter ‘Use
Groups’ on page 12 in the Guide.
What’s on the EDIT PROGRAMS menu …
When the EDIT PROGRAMS menu appears on the screen you have several options: You can move the programs to change the order in which they appear in the lists. You can delete unwanted programs and you can name or rename your programs.
What’s on the ADD PROGRAM menu …
The ADD PROGRAM function is automatic. When tuning of additional programs is complete, the
EDIT PROGRAMS menu appears automatically.
For further information, refer to the chapter ‘Edit
tuned programs’ on page 15.
55
56
>> On-screen menus
TV AUTO TUNING
1 . . . . . . . .
TV MANUAL TUNING
SEARCH
FREQUENCY
. . .
210
PROGRAM NUMBER 1
NAME DR1
EXTRA
TV MANUAL TUNING
FINE TUNE
DECODER
TV SYSTEM
SOUND
0
OFF
B / G
STEREO
DELETES PROGRAM GROUPS start start store
GO accept
GO
What’s on the AUTO TUNING menu …
The AUTO TUNING function is automatic. When tuning of all programs is complete, the EDIT
PROGRAMS menu appears.
What’s on the TV MANUAL TUNING menu …
SEARCH … Start search tuning.
FREQUENCY … Select a frequency to tune in.
PROGRAM NUMBER … Store or change program number. You can store 99 programs.
NAME … Access the naming menu and name the program you have selected.
EXTRA … Access the extra TV MANUAL TUNING menu.
What’s on the extra TV MANUAL TUNING menu …
FINE TUNE … Fine tune the frequency of a program or tuned program. You can fine tune within the range of -8 – +8.
(DECODER) … A decoder is necessary for the reception of coded programs. Usually the decoder is detected automatically during tuning, but it can be selected via this menu option. Set
DECODER to one of following options: ON (for decoder on) or OFF (for no decoder).
(TV SYSTEM) … TV broadcast system – this option is only available on certain types of TV sets, as the TV broadcast system is usually selected automatically.
SOUND (mono, stereo or language) … Several types of sound may be available for different programs, mono, stereo or different languages.
On the relevant program or frequency select the options MONO (FM / NICAM mono sound),
STEREO (NICAM / A2 stereo sound), MONO1
(mono language 1), MONO2 (mono language 2),
MONO3 (mono language 3), or STEREO2 (stereo language 2).
Even though you store a type of sound/language, you can switch between the various types while watching a TV programme. For further information, refer to the chapter ‘Adjust sound and picture’ on page 8 in the Guide.
RADIO MANUAL TUNING
FM / DAB
SEARCH
FM
92.6
FREQUENCY . . .
PROGRAM NUMBER 10
NAME
FINE TUNE
SOUND
STRUER
0
STEREO store
GO
RADIO MANUAL TUNING
FM / DAB
SEARCH
CHANNEL
DAB
. . .
12 C
PROGRAM
DR DAB
DR SOFT
PROGRAM NUMBER 10
NAME DR SOFT store
GO
ADJUST DAB AERIAL
.......................
.......................................
CHANNEL
DR DAB
12 C
What’s on the FM RADIO TUNING menu …
FM/DAB … Choose between FM and DAB*.
SEARCH … Start searching the frequency band up or down.
FREQUENCY … Select a frequency to tune in.
PROGRAM NUMBER … Store or change program number. You can store 99 programs.
NAME … Access the naming menu and name the program you have selected.
FINE TUNE … Fine tune the frequency of a program or tuned program. You can fine tune within the range of -4 – +8.
SOUND … Choose between stereo or mono. The receiver will switch automatically to Mono sound if the Stereo signal is affected by noise.
What’s on the DAB RADIO TUNING menu …
FM/DAB … Choose between FM and DAB*.
SEARCH … Start searching the frequency band up or down.
CHANNEL … Select a channel to tune in. Enter the channel number by means of the number buttons, change between letters by means of the arrow buttons left and right.
(ENSEMBLE) … This field informs you of the found ensemble, no selection can be made here.
PROGRAM … Choose between different programs within the found ‘ensemble’.
PROGRAM NUMBER … Store or change program number. You can store 99 programs.
NAME … Access the naming menu and name the program you have selected.
What’s on the ADJUST DAB AERIAL* menu …
When an ‘ensemble’ has been found, this menu can be used to optimise signal reception.
The bar at the top of the menu shows the reception quality.
If no ensembles have been found, you can enter a channel number by means of the number buttons, change between letters by means of the arrow buttons left and right, and then move the DAB aerial until an ‘ensemble’ name appears in the menu.
57
*Receiving DAB radio programs is only possible if your television is equipped with the optional DAB module and DAB radio is transmitted in your area.
58
>> On-screen menus
DYNAMIC RANGE CONTROL MENU
OFF MIDDLE MAX
....................................
.......................................
STYLE
RADIO DISPLAY
MAXIMUM
??? TEXT TEXT TEXT ???
RADIO 3
BBC CLASSIC
BBC National DAB
TV RECORD
NOW
TELETEXT
RECORD LIST
MENU
BBC select
GO store
GO store
GO
What’s on the DYNAMIC RANGE CONTROL menu …
For certain DAB programs, you can adjust audio signal compression with the DRC (Dynamic Range
Control) function. Compression compensates for sources of noise in your immediate surroundings.
There are twelve possible settings, with three values to guide you:
OFF (no compression)
MIDDLE (recommended by the DAB provider)
MAX (maximum compression, twice that recommended by the DAB provider).
DAB DRC menu settings have no effect for programs not broadcast with DRC.
What’s on the RADIO DISPLAY menu …
STYLE … Select the display settings for when you listen to radio. Options are:
MAXIMUM … Shows text sent out by the broadcaster continuously, as well as radio program number, name of the radio program, frequency or ‘ensemble’ name.
TIME OUT … Shows the maximum display but removing the display when the text sent out by the broadcaster has been shown once.
MINIMUM … Shows the radio program number and the name of the radio program.
OFF … No display in radio mode.
What’s on the TV RECORD menu …
NOW … Use this option to make an instant recording. Alternatively, press RECORD twice to make an instant recording.
TELETEXT … Use this option to make a timed recording via teletext.
RECORD LIST … Use this option to check or delete your recordings.
MENU … Use this option to make a timed recording via the recording menu.
This menu is only available if a BeoCord V 8000 is connected to your television.
Some of the features of the BeoCord V 8000 function differently with this television than described in the BeoCord V 8000 Guide, and some are not available. A supplement for the
BeoCord V 8000 Guide is available from your
Bang & Olufsen retailer.
SOURCE
PROGRAM
START TIME
STOP TIME
DAYS
. . .
TIMER PROGRAMMING
TV
18 BBC
15:40
16:40
M . . TF . S
WAKE UP TIMER
SOURCE
PROGRAM
START TIME
ON / OFF
TV
21 BBC
07:00
ON
VIDEO
AUDIO
STANDBY
STAND POSTIONS store
GO store
GO select
GO
What’s on the TIMER PROGRAMMING menu …
SOURCE
Choose the source for your Timer from the available sources in your system. Choose
STANDBY, if you want the television to switch off. If you have other compatible video or audio systems connected to your television, they are switched off as well.
PROGRAM (Program number) … Once your source is chosen, choose the program number you want.
START TIME and STOP TIME … Key in the times when you want the system to start and/or stop playing. If you have set the Timer source to
STANDBY, it is only possible to enter a stop time.
DAYS … Select the specific weekday(s) on which you want your Timer executed. All the weekdays will be displayed – starting with M for
Monday.
What’s on the WAKE-UP TIMER menu …
SOURCE … Choose the source for your Wake-up
Timer from the available sources in your system.
PROGRAM (Program number) … Choose the program number you want.
START TIME … Key in the time when you want the system to start playing.
ON/OFF … Activate or deactivate your Wake-up
Timer. Choose ON to activate and OFF to deactivate.
What’s on the STAND POSITIONS menu …
VIDEO … Select the position you want the television to turn to when you switch on a video source.
AUDIO … Select the position you want the television to turn to when you switch on an audio source*.
STANDBY … Select the position you want the television to turn to when it is switched off.
*This only applies if no external speakers are connected to the television.
This menu is only available if your television is equipped with an optional motorised stand.
You can only use a source, such as A.MEM, if it is present in your setup.
59
NOTE! Remember to activate your Timer by setting TIMER PLAY to ON, if you want the Timer to apply to the television.
60
>> On-screen menus
AV1
AV 2
CONNECTIONS
V. MEM
NONE
VOLUME
BALANCE
BASS
TREBLE
LOUDNESS
SOUND SETUP
. . . . . . . .
. . . . . . . .
. . . . . . . .
. . . . . . . .
ON
BRIGHTNESS
CONTRAST
COLOUR
PICTURE
. . . . . . . .
. . . . . . . .
. . . . . . . .
store
GO store
GO store
GO
What’s on the CONNECTIONS menu …
AV 1
NONE … if no equipment is connected.
V.MEM … if you have connected a Bang &
Olufsen video recorder or any other video recorder.
V.MEM+DECODER … if you have connected a
Bang & Olufsen video recorder with a decoder connected to it.
V.MEM+STB … if you have connected a Bang &
Olufsen video recorder with a set-top box connected to it.
DECODER … if you have connected a decoder.
V.AUX … if you have connected any other type of auxiliary equipment.
STB … if you have connected a set-top box.
What’s on the SOUND SETUP/SOUND
ADJUSTMENT menu …
VOLUME … Adjusts the volume level the TV uses when you switch it on.
(CENTRE) … Only available if you have connected loudspeakers to the television. Adjusts the balance between the external and internal speakers.
(BALANCE) … Adjusts the balance between the speakers.
BASS … Adjusts the bass level.
TREBLE … Adjusts the treble level.
LOUDNESS … The loudness feature compensates for the human ear’s lack of sensitivity to high and low frequencies. These frequencies are boosted at low volume levels so that low music becomes more dynamic. Loudness can be set to
ON or OFF.
What’s on the PICTURE menu …
BRIGHTNESS … Adjusts the picture brightness.
CONTRAST … Adjusts the contrast level in the picture.
COLOUR … Adjusts the colour intensity in the picture.
For video sources using the NTSC signal, a fourth option – Tint (colour shade or nuance) – will be available for adjustment.
If you connect a Bang & Olufsen video recorder, the only options for V.TAPE are: V.MEM,
V.MEM+STB and V.MEM+DECODER. The contents of this menu varies according to your speaker setup.
AV 2
NONE … if no equipment is connected.
EXPANDER … if you have connected an
Expander box with other auxiliary equipment connected to it.
V.AUX … if you have connected any other type of auxiliary equipment.
DVD … if you have connected a DVD player or similar devices.
STB … if you have connected a set-top box.
TIME
DATE
MONTH
YEAR
SYNCHRONISE
SHOW CLOCK
CLOCK
20:00
23
APR
2001
YES
YES
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA select accept
GO
BRIGHTNESS
CONTRAST
COLOUR
DVI SETUP
31
31
31 store
GO
What’s on the CLOCK menu …
TIME … Indicates the time.
DATE … Indicates the day.
MONTH … Indicates the month.
YEAR … Indicates the year.
SYNCHRONISE … For synchronisation of the builtin clock with teletext.
SHOW CLOCK … Select YES if you want the time to be shown permanently on the screen.
What’s on the MENU LANGUAGE menu …
Choose between the available languages.
What’s on the DVI SETUP menu …
BRIGHTNESS … Adjusts the picture brightness.
CONTRAST … Adjusts the contrast level in the picture.
COLOUR … Adjusts the colour intensity in the picture.
This menu is only available, if you have connected a computer to the television via the DVI socket.
61
62
Index
Beo4 remote control Contact
Add a ‘button’ to the Beo4 list, 52
Changing the Beo4 batteries, Guide p. 18
Cleaning the Beo4, Guide p. 18
Configure Beo4, 52
Customise Beo4, 52
Introducing your television and Beo4,
Guide p. 4
Move extra ‘buttons’, 53
Remove a ‘button’ from the Beo4 list, 52
Replace Beo4 batteries, Guide p. 18
Using Beo4, Guide p. 4
Contact Bang & Olufsen, Guide p. 19
Decoder
Connect a decoder, 36
Displays and menus
Displayed information and menus, Guide p. 5
On-screen menus, 54
BeoLink
Link frequency, 49
Link room operation, 50
Master Link socket, 34
Your television in a link room, 48
Camera
Connect a Camera, 33
Copy from a Camcorder to a videotape, 33
Clock
Set the time and date, 23
What’s on the CLOCK menu, 61
Computer monitor
Adjust picture, 5
Bring up the computer image on the screen, 5
Connect a computer, 35
What’s on the DVI menu, 61
DAB radio
Add new TV or radio programs, 21
Adjust tuned DAB programs, 19
Auto-tuning – first-time setup of your television, 12
Bring up a list of radio programs, Guide p. 14
Delete tuned programs, 16
Edit tuned programs, 19
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
See list of all programs, Guide p. 14
What’s on the ADJUST DAB AERIAL menu, 57
What’s on the DAB DRC menu, 58
What’s on the PROGRAM GROUPS menu, 55
What’s on the RADIO DISPLAY menu, 58
What’s on the RADIO MANUAL TUNING menu, 57
First-time setup
First-time setup procedure, 12
Format
Change the picture format, Guide p. 9
Connections
Aerial and mains connection, 32
Audio system – connect to the television, 44
BeoCord V 8000 video tape recorder, 38
Camera, 33
Connections – your television in a link room, 48
Decoder, 36
Headphones, 33
Link room connections, 48
Loudspeakers, 34
Register additional video equipment, 40
Set-top box, 37
Socket panel, 34
Sockets for temporary connections, 33
What’s on the CONNECTIONS menu, 60
Groups
Create Groups, Guide p. 12
Move programs within a Group, Guide p. 13
Select programs in a Group, Guide p. 12
What’s on the PROGRAM GROUPS menu, 55
Headphones
Connect headphones, 33
Language
Change sound type or language, Guide p. 8
Choose menu language, 26
First-time setup – choose menu language, 12
What’s on the MENU LANGUAGE menu, 61
Loudspeakers
Change speaker balance or combination,
Guide p. 9
Connect speakers, 34
Sound adjustments, 24
What’s on the SOUND ADJUSTMENT menu, 60
Maintenance
About the screen, Guide p. 18
Change Beo4 batteries, Guide p. 18
Handling your television, 30
Maintenance of your television, Guide p. 18
Master Link
Audio system with your television, 44
Connect your audio system, 34
Option setting, 45
Use integrated audio/video system, 46
Position of television
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Stand
Determine the centre position – first-time setup, 14
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Radio
Add new TV or radio programs, 21
Adjust tuned radio programs, 19
Auto-tuning – first-time setup of your television, 12
Bring up a list of radio programs, Guide p. 14
Delete tuned programs, 16
Edit tuned programs, 19
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
Listen to tuned programs, Guide p. 14
See list of all programs, Guide p. 14
What’s on the PROGRAM GROUPS menu, 55
What’s on the RADIO DISPLAY menu, 58
What’s on the RADIO MANUAL TUNING menu, 57
Subtitles
Subtitles from teletext, Guide p. 11
Teletext
Basic teletext functions, Guide p. 10
Day-to-day use of MEMO pages, Guide p. 11
Store favourite teletext pages, Guide p. 11
Timer
Set the television to switch itself on and off, 6
Set the time and date, 23
Timed play and timed standby, 6
View, edit or delete a Timer, 7
Set-top box
Connect a set-top box, 37
Set-top Box Controller menu, 8
Universal Beo4 operation, 9
Use the set-top box in a link room, 9
Use the set-top box’s own menu, 9
Picture
Adjust brightness, colour or contrast, 24
Change the picture format, Guide p. 9
Remove the picture from the screen, 24
What’s on the PICTURE menu, 60
Pincode
Activate the pincode system, Guide p. 16
Change or delete your pincode, Guide p. 16
If you have forgotten your pincode, Guide
p. 17
Use your pincode, Guide p. 17
Placement
Set up your television, 30
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Socket panel
Camera and headphones sockets, 33
Socket panel, 34
Sound
Adjust or mute the sound, Guide p. 8
Adjust volume, bass or treble, 25
Change sound type or language, Guide p. 8
Change speaker balance or combination,
Guide p. 9
What’s on the SOUND ADJUSTMENT menu, 60
Tune
Add new radio or TV programs, 21
Adjust tuned programs, 18
Auto-tuning – first-time setup of your television, 13
Delete tuned programs, 16
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
What’s on the ADD PROGRAMS menu, 55
What’s on the AUTO TUNING menu, 56
What’s on the extra TV MANUAL TUNING menu, 56
What’s on the RADIO MANUAL TUNING menu, 57
What’s on the TV MANUAL TUNING menu, 56
63
64
>> Index
TV programs
Add new TV programs, 21
Adjust tuned programs, 18
Auto-tuning – first-time setup of your television, 13
Bring up a TV list, Guide p. 6
Delete tuned programs, 16
Edit tuned programs, 15
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
Select a TV program, Guide p. 6
What’s on the ADD PROGRAMS menu, 55
What’s on the AUTO TUNING menu, 56
What’s on the EDIT PROGRAMS menu, 55
What’s on the extra TV MANUAL TUNING menu, 56
What’s on the PROGRAM GROUPS menu, 55
What’s on the TV MANUAL TUNING menu, 56
Wake-up Timer
Enter a Wake-up Timer, 4
Check or delete a Wake-up Timer, 4
Set the time and date, 23
65
66
Waste Electrical and Electronic Equipment
(WEEE) – Environmental protection
The European Parliament and the Council of the
European Union have issued the Waste Electrical and Electronic Equipment Directive. The purpose of the Directive is the prevention of waste of electrical and electronic equipment, and to promote the reuse and recycling and other forms of recovery of such waste. As such the Directive concerns producers, distributors and consumers.
When disposing of electrical and electronic equipment by use of the collection systems available in your country, you protect the environment, human health and contribute to the prudent and rational use of natural resources. Collecting electrical and electronic equipment and waste prevents the potential contamination of nature with the hazardous substances which may be present in electrical and electronic products and equipment.
The WEEE directive requires that both manufacturers and end-consumers dispose of electrical and electronic equipment and parts in an environmentally safe manner, and that equipment and waste are reused or recovered for their materials or energy.
Electrical and electronic equipment and parts must not be disposed of with ordinary household refuse; all electrical and electronic equipment and parts must be collected and disposed of separately.
Your Bang & Olufsen retailer will assist with and advise you of the correct way of disposal in your country.
Small products may not always be marked with the pictogram in which case this is present in the instructions for use, on the guarantee certificate and printed on the packaging.
Products and equipment which must be collected for reuse, recycling and other forms of recovery are marked with the pictogram shown.
This product fulfils the conditions stated in the EEU directives 89/336 and 73/23.
Technical specifications, features and the use thereof are subject to change without notice.
3507804
0710
www.bang-olufsen.com
Download
Public link updated
The public link to your chat has been updated.
Document public link
Advertisement
Key features
- Wake-up Timer functionality
- Can be used as a computer monitor
- Timed play and standby functions
- Set-top box operation via Beo4 remote
- Automatic tuning of TV and radio programs
- BeoLink system integration