BeoCenter 6–23 Reference book

BeoCenter 6–23 Reference book
BeoCenter 6–23
Reference book
Tables of contents in the Reference book
The contents of this Reference book is divided into sections. Each particular section
starts with its own detailed table of contents provided with page references. Texts
in black refers to the current section, whereas the remaining sections are described
in general terms and written in grey.
The main sections are:
• Advanced operation
• Tuning and preference settings
• Placement, sockets and connections
• BeoLink system
• On-screen menus
• Index
Advanced operation
This chapter tells you how to operate
your television beyond daily use.
It also tells you how to operate a
connected set-top box and other
connected video equipment.
•
•
•
•
Wake-up Timer, 4
Use your television as a computer monitor, 5
Set the television to switch itself on and off, 6
Set-top box operation, 8
Tuning and preference settings, 11
Find out how to set up your television for the first time and tune in programs.
This chapter also contains information about settings for time, date, stand positions,
picture and sound.
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television
and how to register extra equipment.
BeoLink system, 43
Find out how to connect an audio system to your television and operate an
integrated audio/video system. Find out how to make link connections, operate a
link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
3
Wake-up Timer
4
You can make the television wake
you up in the morning.
Check or delete a Wake-up Timer
Enter a Wake-up Timer
WAKE UP TIMER
The Wake-up Timer is a once-only
Timer, it lasts for one hour. Like an
alarm clock, it is disabled once it has
been executed. It applies only to the
television it has been programmed
on.
Once you have made one Wake-up
Timer, the television automatically
suggests the time you entered for the
latest Wake-up Timer when you enter
a new one.
Wake-up Timers can, of course, also
be disabled again.
When you have programmed a Wakeup Timer, the television cannot be
part of an ordinary Play Timer or
Standby Timer until the Wake-up
Timer has been carried out or
disabled.
PLAY TIMER
SOURCE
TV
TIMER ON / OFF
PROGRAM
21 BBC
TIMER LIST
START TIME
07:00
ON / OFF
ON
OFF
TIMER PROGRAMMING
WAKE UP TIMER
store
GO
07:00
select
GO
You must choose the source and program
number of your Wake-up Timer as well as the
start time.
You can call up the settings for the Wake-up
Timer to check the time or to disable the
Wake-up Timer by setting it to OFF.
To enter settings for a Wake-up Timer …
> Press MENU to bring up the TV SETUP menu
and press to highlight PLAY TIMER.
> Press GO to bring up the PLAY TIMER menu and
press to highlight WAKE UP TIMER.
> Press GO to bring up the WAKE UP TIMER
menu.
> Press or to move through the menu items.
> Use the number buttons to enter information or
press or to view your choices for each item.
> When you have filled in the required
information, press GO to store your Wake-up
Timer.
> Press EXIT to exit all menus.
To change settings for a Wake-up Timer or
delete it …
> Press MENU to bring up the TV SETUP menu
and press to highlight PLAY TIMER.
> Press GO to bring up the PLAY TIMER menu and
press to highlight WAKE UP TIMER.
> Press GO to bring up the WAKE UP TIMER
menu.
> Press or to move through the menu items.
> Use or to change settings or enter a new
time with the number buttons. Change the ON/
OFF setting to OFF if you wish to delete the
Wake-up Timer.
> When you have made your changes, press GO
to store them.
> Press EXIT to exit all menus.
Use your television as a computer monitor
If you connect your television to a
computer, as described on page 37,
you can use it as a monitor.
IMPORTANT! If you wish to connect a
computer to the television and use the
television as a monitor, make sure that you
disconnect the television, the computer,
and all equipment connected to the
computer from the mains before you
connect the computer and the television
to each other.
When in use, the computer must be
connected to a grounded wall outlet as
specified in the computer’s setting-up
instructions.
Bring up the computer image on the
screen
To see the computer picture on the television
screen, you must bring it up with Beo4.
To bring up the computer picture …
Press repeatedly until PC appears LIST
PC
in the Beo4 display
Press to bring up the picture
You can then operate the
computer as you normally
would.
5
Picture adjustments
DVI SETUP
BRIGHTNESS
31
CONTRAST
31
COLOUR
31
GO
When you have the computer picture on the
screen, you must call up the DVI SETUP menu
to make adjustments to brightness, contrast
and colour.
> Press MENU to bring up the DVI SETUP menu.
> Press or to move between the menu
options.
> Press or to adjust settings.
> Press GO to store your settings and exit the
menu.
The settings you make in this menu only apply to
the PC setup.
Set the television to switch itself on and off
6
You can make your television switch
itself on and off automatically via the
timed play and timed standby
functions, if, for example, there is a
programme you do not want to miss.
Enter as many as six Timer settings,
and bring up an on-screen list of the
Timer settings you have entered.
From this list, you can edit or delete
your Timer settings.
If your television is integrated with a
Bang & Olufsen audio system with a
Master Link cable, these systems can
perform the timed play or timed
standby functions as well.
For your timed settings to be
executed correctly, ensure that the
built-in clock is set to the correct
time. For further information, refer to
the chapter ‘Set the time and date’
on page 23.
Before you start …
Timed play and timed standby
If you connect a Bang & Olufsen audio or video
product to your television with a Master Link
cable, you can exclude or include it in timed
functions via the Play Timer menu. For
example, set the television’s Play Timer to ON
and an audio system’s Play Timer to OFF if you
wish timed functions to apply only to the
television.
You can preset your television to start and
stop automatically at the same time and day
every week.
To switch on the Play Timer …
> Press MENU to bring up the TV SETUP menu
and press to highlight PLAY TIMER.
> Press GO to bring up the PLAY TIMER menu,
and press or to highlight TIMER ON/OFF.
> Press GO to bring up the TIMER ON/OFF menu.
> Press or to reveal ON.
> Press GO to store the setting.
For further information about how to switch the
Play Timer on or off for a connected Bang &
Olufsen audio or video product, refer to the Guide
enclosed with the product.
NOTE! If your television is set up in a link room,
Timer programming must be carried out on your
main room system.
To enter settings for timed play or timed
standby …
> Press MENU to bring up the TV SETUP menu and
press to highlight PLAY TIMER.
> Press GO to bring up the PLAY TIMER menu and
press to highlight PLAY TIMER
PROGRAMMING.
> Press GO to bring up the PLAY TIMER
PROGRAMMING menu.
> Press or to move through the menu items.
> Use the number buttons to enter information or
press or to view your choices for each item.
When DAYS is highlighted, press once to be
able to move through the days, and press or
to remove a day you do not want. Press to
move to the next day, and press to move back
to a previous day. When the weekday(s) you
want are displayed, press GO to accept the
day(s).
> When you have filled in the required information,
press GO to store your Timer settings.
> Press EXIT to exit all menus.
7
View, edit or delete a Timer
Bring up an on-screen list of the settings you
have entered. From this list, you can edit or
delete your Timer settings.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
TIMER SETUP
OPTIONS
TIMER ON / OFF
STAND POSITIONS
ON
TIMER INDEX
PLAY TIMER PROGRAMMING
TIMER ON / OFF
TIMER INDEX
OFF
PLAY TIMER PROGRAMMING WAKEUP TIMER
select
GO
SOURCE
PROGRAM
START TIME
select
GO
TIMER PROGRAMMING
SOURCE
TV
PROGRAM
18 BBC
START TIME
15:40
STOP TIME
16:40
DAYS
M . . TF . S
...
store
Abbreviations for days of the week:
M … Monday
T…
Tuesday
W … Wednesday
T…
Thursday
F…
Friday
S…
Saturday
S…
Sunday
GO
To view, edit or delete your Timer settings …
> Select TIMER INDEX from the TIMER SETUP
menu to bring up your list of Timer settings.
The first Timer setting in the list is already highlighted.
> Press or to move the cursor to a Timer
setting you wish to edit.
> To edit a setting, press GO and follow the
procedure described to the left.
> To be able to delete a selected setting, press the
yellow button.
> If you change your mind, press to move the
setting back into the list. You can also press
EXIT to exit all menus.
> Press the yellow button a second time to delete
the setting.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
TIMER SETUP
PLAY TIMER
OPTIONS
TIMER ON / OFF
STAND POSITIONS
TIMER INDEX
ON
PLAY TIMER PROGRAMMING
TIMER ON / OFF
TIMER INDEX
WAKEUP TIMER
OFF
PLAY TIMER PROGRAMMING
select
15:40-16:40
BBC
GO
TV 18
M . . TF . .
select
GO
PLAY TIMER INDEX
15:40-16:40
BBC
TV 18
M . . TF . .
6:00 - 7:00
ZDF
TV 3
MTWTF . .
20:00-22:00
CNN
TV 15
MT . . . S .
delete
edit
GO
Set-top box operation
8
The built-in Set-top Box Controller
acts as an interpreter between a settop box of your choice and the Beo4
remote control. When a set-top box
is connected, you can use the Beo4
remote control to gain access to the
programs and functions offered by
your set-top box.
Some functions are immediately
available via Beo4 when you switch
on the set-top box. Additional
functions are available through a
Set-top Box Controller menu that you
bring up on the screen.
Set-top Box Controller menu
Some of the buttons on your set-top box
remote control are not immediately available
on Beo4. To find out which Beo4 buttons
activate specific services or functions in your
set-top box, bring up the Set-top Box
Controller menu on the screen.
Press to switch on the set-top
box
DTV
Press to bring up the Set-top Box
Controller menu
MENU
Press the number button that
activates the function you want,
or …
1–9
… press one of the coloured
buttons to activate a function
1
GUIDE
2
MENU
3
TEXT
4
INFO
5
WIDE
1
GUIDE
2
MENU
3
TEXT
4
INFO
5
WIDE
Example of a Set-top Box Controller menu – The
Beo4 buttons are shown to the left on the menu
and the set-top box buttons are shown to the right.
9
Universal Beo4 operation
Use the set-top box’s own menu
Use a set-top box in a link room
If you know which Beo4 button activates the
function you want, you can activate the
function without bringing up the Set-top Box
Controller menu first.
Once you have activated your set-top box,
you can operate the set-top box’s own
menus, such as the program guide, via Beo4.
When your set-top box is connected to the
television in the main room, you can operate
the set-top box from the link room television.
However, the Set-top Box Controller menu
cannot be displayed on the television screen
in the link room.
While your set-top box is
activated …
Press GO and then the number
button that activates the
function you want
While the set-top box’s own
menu is shown …
Moves the cursor up or down
GO
1–9
Press to switch on the set-top
box in the main room
DTV
Press GO and then the number
button that activates the
function you want
GO
1–9
Moves the cursor left or right
Press one of the coloured
buttons to activate a function
Selects and activates a function
GO
GO
Press GO and then or to
step up or down through
programs directly
GO
Press GO and then or to
step between menu pages or
step in program lists
GO
Press and hold GO to bring up
the Program guide or the ‘Now/
Next’ banner on the screen
depending on your set-top box
GO
Exits menus, or returns to a
previous menu*
STOP
Exits menus, enters or exits
different modes, such as radio
EXIT
Use the coloured buttons as
indicated in the menus of your
set-top box
*Depending on your set-top box,
you may have to press EXIT twice
instead of STOP to return to a
previous menu.
When set-top box is selected as
source, press MENU twice to
bring up the television’s main
menu.
Press one of the coloured
buttons to activate a function
10
Tuning and preference settings
Find out how to perform the firsttime setup procedure and tune in all
available programs automatically. In
addition, you can find information
about how to edit tuned programs
and adjust other available settings,
such as time, date, picture and sound.
For information about how to place
your television and connect
additional video equipment, refer to
the chapter ‘Placement, sockets and
connections’ on page 29.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to
operate timed play and timed standby functions, and a connected set-top box.
Tuning and preference settings, 11
•
•
•
•
•
•
•
•
First-time setup of your television, 12
Edit tuned programs, 15
Re-tune or add programs, 20
Set positions for the television to turn to, 22
Set the time and date, 23
Adjust picture and sound settings, 24
Choose menu language, 26
Choose radio display, 27
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television
and how to register extra equipment.
BeoLink system, 43
Find out how to connect an audio system to your television and operate an
integrated audio/video system. Find out how to make link connections, operate a
link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
11
First-time setup of your television
12
The setup procedure described here
is activated only when the television
is connected to the mains and
switched on for the first time.
You must select the menu language,
register any extra equipment you
have connected, choose radio display,
determine the centre position for the
motorised stand – if you television is
equipped with one – and start the
automatic tuning of TV and radio
programs.
Register extra equipment before
auto-tuning
Select menu language
MENU LANGUAGE
CONNECTIONS
DANSK
AV1
V. MEM
DEUTSCH
AV 2
DVD
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
select
accept
GO
The first time you switch on your television,
you must select which language you want all
the menus to be displayed in.
The menu language setup appears. If you wish to
change the menu language at a later date, you
can find the item under OPTIONS in the TV SETUP
menu.
> Press TV to switch on the television. The
language menu appears.
> Press or to move between the displayed
languages, if necessary.
> Press GO to store your choice.
store
GO
Some extra equipment is detected by the
television automatically. You can check and
confirm the registration of the equipment
involved.
When the CONNECTIONS menu appears …
> Press or to step between menu items: AV 1
and AV 2.
> If necessary, press or to select the option
that corresponds to what you have connected
to the socket.
> Press GO to store this setup.
13
Select radio display
Store all programs and settings
AUTO TUNE
RADIO DISPLAY
STYLE
MAXIMUM
CHECK AERIAL CONNECTION
TV
RADIO
GERNO VERSI FOLLOW EPIUM
RADIO 3
BBC CLASSIC
BBC National DAB
store
GO
Before tuning in programs, you are prompted
to select the display type you want to appear
on the television screen when you select
radio as your source.
When the DISPLAY SETUP menu appears …
> Press or to switch between available
settings. The chosen display type is shown in
the menu as you change settings.
> Press GO to store your choice.
start
GO
When you have made your selections, a menu
for program tuning automatically appears on
the screen.
When the menu for auto tuning appears, the
prompt CHECK AERIAL CONNECTION appears to
remind you to check that your TV aerial and radio
aerial are properly connected.
> Press GO to start auto tuning. The television
tunes in all available programs.
14
>> First-time setup of your television
Determine the centre position
If your television is equipped with the
optional motorised stand, the STAND
ADJUSTMENT menu appears on the screen.
Once the centre position is determined, select
your favourite positions for when the
television is switched on and in standby.
When the STAND ADJUSTMENT menu
appears …
> Press GO to start stand adjustment.
> If the adjustment is interrupted the text
‘ADJUSTMENT FAILED’ appears on the screen.
Remove obstacles preventing the television
from turning, and press GO to start adjustment
again.
> Once adjustment is complete, the text
‘ADJUSTMENT OK’ appears, followed by the
STAND POSITIONS menu.
> Move between the different stand positions;
VIDEO, AUDIO and STANDBY by means of
and and press GO to enter the menu.
> To turn the television, press or .
> Press the green button to store each of the
positions.
STAND ADJUSTMENT
CENTRE POSITION
CALIBRATING . . .
adjust
GO
Make sure that there is enough room for the television to turn to the right and left.
For further information about stand positions,
refer to the chapter ‘Set positions for the television to turn to’ on page 22.
Edit tuned programs
If automatic tuning of all radio
programs results in more than 99
programs, the EDIT RADIO
PROGRAMS menu appears
automatically after tuning. You must
then move the radio programs you
want to a position within 1 and 99 in
the list.
You can at any time rearrange the
order in which your radio and TV
programs appear, just call up the EDIT
RADIO PROGRAMS or EDIT TV
PROGRAMS menus to do so. These
menus also allow you to name and
delete radio and TV programs.
If the tuned programs require
additional editing, such as fine tuning,
use the MANUAL TUNING menu.
15
Move tuned radio programs
Once automatic tuning of programs has been
completed, the EDIT RADIO PROGRAMS
menu appears automatically and you can
move your tuned programs.
> Press to start editing your radio programs.
> Press or to select the program you wish to
move.
> Press once move the program out of the list.
> Press or to move the program to the
desired program number.
> Press to make the program move back into
the list or change places with the program
which occupies the desired program number.
> Now, move the program which you changed
places with to an empty program number or to
a number already occupied and repeat the
procedure.
> When you have moved the relevant programs,
press STOP to back up through all menus, or
press EXIT to exit all menus.
EDIT RADIO PROGRAMS
91
92
93
94
95
96
97
98
99
DR P1
DR SOFT
........
SKYRADIO
DR JAZZ
SR SOFT
........
NRK JAZZ
........
TOO MANY STATIONS!
MOVE WANTED STATIONS UP
TO THE NUMBERED PROGRAM
SLOTS
start
EDIT RADIO PROGRAMS
91
92
93
94
95
96
97
98
99
DR P1
DR SOFT
........
SKYRADIO
DR JAZZ
SR SOFT
........
NRK JAZZ
........
THEVOICE
........
BBC POP
BBC JAZZ
KW5 HITS
........
........
........
move
GULD FM
move
delete
EDIT RADIO PROGRAMS
91
92
93
94
95
96
97
98
99
DR P1
DR SOFT
........
GULD FM
DR JAZZ
SR SOFT
........
NRK JAZZ
........
THEVOICE
........
BBC POP
BBC JAZZ
KW5 HITS
........
........
........
move
SKYRADIO
move
delete
Note that all programs placed on program
numbers higher than 99 are deleted when you
exit this menu.
16
>> Edit tuned programs
Move or delete tuned programs
Once the automatic tuning of programs is
completed, you can move or delete any tuned
TV or radio programs you do not want.
Move programs …
> Press TV to switch on the television, or RADIO
to switch on the radio.
> Press MENU to bring up the SETUP menu, and
press to highlight TUNING.
> Press GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
> Press GO to bring up the EDIT PROGRAMS
menu.
> Press or to select the program you wish to
move.
> Press once to be able to move the program.
The program is now moved out of the list.
> Press or to move the program to the
desired program number.
> Press to make the program move back into
the list or change places with the program
which occupies the desired program number.
> Now, move the program which you changed
places with to an empty program number or to
a number already occupied and repeat the
procedure.
> When you have moved the relevant programs,
press STOP to back up through all menus, or
press EXIT to exit all menus.
Delete programs …
> Press TV to switch on the television, or RADIO
to switch on the radio.
> Press MENU to bring up the SETUP menu and
press to highlight TUNING.
> Press GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
> Press GO to bring up the EDIT PROGRAMS
menu.
> Press or to move to the program you wish
to delete.
> Press to move the program out of the list.
> Press the yellow button to be able to delete the
program – the program is then shown in red.
> Press the yellow button again to finally delete
the program, or press twice to move the
program back into the list.
> When you have deleted the relevant programs,
press EXIT to exit all menus.
TV SETUP
PROGRAM GROUPS
TUNING
TV TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
LINK FREQUENCY
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
select
GO
1 DR1
2 TV2
3. . .
select
GO
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
..
..
17
18
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
NRK
TV4
more
name
move
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
..
..
17
18
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
NRK
TV4
move
move
delete
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
..
..
17
18
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
NRK
TV4
move
delete
17
Name tuned programs
The EDIT PROGRAMS menu also allows you to
name all programs yourself.
Name programs …
> Press TV to switch on the television, or RADIO
to switch on the radio.
> Press MENU to bring up the SETUP menu, and
press to highlight TUNING.
> Press GO to bring up the TUNING menu. EDIT
PROGRAMS is already highlighted.
> Press GO to bring up the EDIT PROGRAMS
menu.
> Press or to select the program you wish to
name.
> Press the green button to be able to name the
program. The naming menu is now activated.
> Press or to find the individual characters in
the name.
> Press to move to the next character. As you
move, the television suggests possible names,
but you can still use and , or and to
enter or edit all the characters in the name you
choose.
> Press GO to store the name.
> If necessary, repeat the procedure and name
other program numbers.
> When you have named the relevant programs,
press GO to accept your edited list, or press
EXIT to exit all menus.
TV SETUP
PROGRAM GROUPS
TUNING
TV TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
LINK FREQUENCY
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
1 DR1
2 TV2
3. . .
select
GO
select
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
9
..
..
17
18
DR1
A
ZDF
RTL7
........
BBC
NRK
TV 4
character
next
accept
NRK
TV4
more
name
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
..
..
17
18
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
........
GO
move
GO
18
>> Edit tuned programs
Adjust tuned TV programs – manual tuning
You can store TV programs on program
numbers of their own. Fine tune the program
reception, indicate the presence of coded
programs and choose appropriate sound
types for the individual programs.
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight TUNING.
> Press GO to bring up the TV TUNING menu and
press to highlight MANUAL TUNING.
> Press GO to bring up the TV MANUAL TUNING
menu.
> Press or to move between items on the
menu.
> Press or to view your choices for each item.
> If you choose NAME, then press the green button
to start the naming procedure. Use or and
to enter the characters in the name you
choose.
> To bring up the extra TV MANUAL TUNING
menu, move to EXTRA and press GO. Now fine
tune if relevant, or select type of sound.
> When you have finished editing, press GO to
accept the settings.
> Press GO to store the adjusted program.
> Press EXIT to exit all menus.
If the item SYSTEM appears on the menu, then
make sure that the correct broadcast system is
displayed before you begin tuning:
B/G … for PAL/SECAM BG
I…
for PAL I
L…
for SECAM L
M … for NTSC M
D/K … for PAL/SECAM D/K
If programs are broadcasted with two languages
and you want both languages, you can store the
program twice, once with each language.
TV SETUP
PROGRAM GROUPS
TUNING
TV TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITION
MANUAL TUNING
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
LINK FREQUENCY
select
SEARCH
FREQUENCY
PROGRAM NUMBER
GO
select
GO
TV MANUAL TUNING
SEARCH
...
FREQUENCY
210
PROGRAM NUMBER
1
NAME
DR1
EXTRA
start
store
GO
TV MANUAL TUNING
FINE TUNE
0
DECODER
OFF
TV SYSTEM
B/G
SOUND
STEREO
accept
TV MANUAL TUNING
SEARCH
...
FREQUENCY
210
PROGRAM NUMBER 1
NAME
DR1
EXTRA
TUNING STORED
GO
19
Adjust tuned FM or DAB programs – manual tuning
If your television is equipped with the
optional DAB module, you can tune in both
FM and DAB radio programs. During first
time setup both types of radio programs are
tuned in.
> Press RADIO to switch on the radio.
> Press MENU to bring up the SETUP menu and
press to highlight TUNING.
> Press GO to bring up the RADIO TUNING menu
and press to highlight MANUAL TUNING.
> Press GO to bring up the RADIO MANUAL
TUNING menu.
> Press or to move between items on the
menu.
> Press or to view your choices for each item.
> When you switch between FM and DAB the
menu changes appearance.
> If you choose NAME, then press the green
button to start the naming procedure. Use
or and to enter the characters in the
name you choose.
> When you have finished editing, press GO to
accept the settings.
> Press GO to store the adjusted program.
> Press EXIT to exit all menus.
RADIO MANUAL TUNING
RADIO MANUAL TUNING
FM / DAB
FM
FM / DAB
SEARCH
92.6
SEARCH
...
FREQUENCY
...
CHANNEL
12 C
PROGRAM NUMBER
10
NAME
STRUER
FINE TUNE
0
SOUND
STEREO
DR DAB
store
174.928MHz
239.200MHz
- - - 12A 12B 12C 12D - - - 13F
Ensemble
PROGRAM
DR SOFT
PROGRAM NUMBER
10
NAME
DR SOFT
store
GO
DAB BAND III
5A 5B 5C 5D 6A - - Channels
DAB
DR
DR
DR
…
…
…
…
…
DR
DR
NEWS
SOFT
ROCK
BOOGIE
SPORT
GO
Digital Audio Broadcast (DAB) providers send
program groups called ensembles. A channel
contains a single ensemble, and an ensemble
typically contains 5–10 programs. Some DAB
providers call an ensemble a ‘multiplex’, or call a
program a ‘service’.
Re-tune or add programs
20
You can make your television find
your TV and radio programs for you.
Preset up to 99 different TV and
radio programs on program numbers
of their own and give each program
a distinct name.
You can tune in new programs, for
example, if you move – or re-tune
previously deleted programs.
When tuning in programs via the
ADD PROGRAM menu, your
previously tuned programs are left
unchanged. This allows you to keep
program names, their order in the TV
or radio lists, and any special settings
you may have stored for those
programs, such as decoder or
broadcast system settings.
Re-tune via automatic tuning
You can re-tune all your TV and radio
programs by letting the television tune in all
the programs automatically.
> Press TV to switch on the television, or RADIO
to switch on the radio.
> Press MENU to bring up the SETUP menu and
press to highlight TUNING.
> Press GO to bring up the TUNING menu and
press to highlight AUTO TUNING.
> Press GO to bring up the AUTO TUNING menu.
> Press to start auto tuning.
> Once auto tuning is completed, the EDIT
PROGRAMS menu appears. You can then
rearrange the program order, delete programs
or rename them.
TV SETUP
PROGRAM GROUPS
TV TUNING
TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
LINK FREQUENCY
EDIT PROGRAMS
ADD PROGRAM
AUTO TUNING
1 DR1
2 TV2
3. . .
select
GO
select
GO
TV AUTO TUNING
1 ........
DELETES PROGRAM GROUPS
start
TV AUTO TUNING
1 DR1
2 TV2
3 ........
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
9
..
..
17
18
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
........
NRK
TV4
more
name
move
Please note: If you re-tune all your TV and radio
programs, all Groups of programs and program
settings you have made disappear!
21
Add new programs
You can add a new program or update a
tuned program which, for example, has been
moved by the broadcaster.
TV SETUP
PROGRAM GROUPS
TUNING
TV TUNING
TIMER RECORDING
> Press TV to switch on the television, or RADIO
to switch on the radio.
> Press MENU to bring up the SETUP menu and
press to highlight TUNING.
> Press GO to bring up the TUNING menu and
press to highlight ADD PROGRAM.
> Press GO to bring up the ADD PROGRAM menu.
> Press to start. New programs are added
automatically as they are found.
> When tuning is completed and new programs
have been added, the EDIT PROGRAMS menu
appears. You can then rearrange the program
order, delete programs or rename them. The
cursor highlights the first new program of those
just added to the list.
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
LINK FREQUENCY
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
19 . . . . . . . .
20 . . . . . . . .
21 . . . . . . . .
select
GO
select
ADD TV PROGRAM
10
11
12
13
14
15
16
17
18
19
........
........
CNN
N3
........
SAT 1
SVT 2
NRK
TV4
........
start
GO
Set positions for the television to turn to
22
If your television is equipped with the
optional motorised stand, you can
turn it using the Beo4 remote control.
Furthermore, you can program the
television to turn automatically to
face your favourite viewing position
when you switch on the television,
turn to a different position when you
listen to radio, and turn away to a
standby position when you switch it
off.
You can also turn your television by
hand.
Choose one position for when you switch the
television on, one for radio and one for when
you switch it off.
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight STAND POSITIONS.
> Press GO to bring up the STAND POSITIONS
menu.
> Press GO to determine the VIDEO position.
> Press or to turn the television, and place it
according to your viewing position.
> Press GO to store the position.
To store a stand position for when the radio
is switched on …
> Press to move to AUDIO.
> Press GO to determine the AUDIO position.
> Press or to turn the television, and place it
as you wish.
> Press GO to store the position.
NOTE! For information about first-time installation
of the motorised stand, refer to the chapter ‘Firsttime setup of your television’ on page 12.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
OPTIONS
STAND POSTIONS
STAND POSITIONS
VIDEO
TV ON
TV STANDBY
AUDIO
STANDBY
select
GO
select
GO
To store a stand position for when the
television is switched off and in standby …
> Press to move to STANDBY.
> Press GO to determine the STANDBY position.
> Press or to turn the television, and place it
as you wish.
> Press GO to store the position.
> Press EXIT to leave the menus.
Set the time and date
When you preset your television to
switch itself on or off at a particular
time, or when you preset a timed
recording of a programme on a
connected video recorder, the clock
ensures that these features are
switched on and off at the right
times.
The simplest way to set the clock is
to synchronise it with a tuned TV
program’s teletext service via the
CLOCK menu. If you choose to
synchronise the clock, this is done
with the teletext service offered by
the TV program you are currently
watching. If a teletext service is not
available, you can set the clock
manually.
Before synchronising the clock with a tuned
program, make sure that the program you are
watching offers a teletext service.
23
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
To bring up the clock in the display, press LIST
repeatedly to display CLOCK* on Beo4, then
press GO. To remove the clock again, repeat
the procedure.
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and
press to highlight CLOCK.
> Press GO to bring up the CLOCK menu.
> Press or to see your choices for each item.
> Press or to move through menu items. It is
only necessary to enter the time manually if
SYNCHRONISE is set to NO.
> Press GO to store your clock and calendar
options, or …
> … press EXIT to exit all menus without storing.
If the clock is not updated in the transition between
summer and winter time, simply select the program
with which you originally synchronised the clock,
and the clock is updated.
*NOTE! In order to display CLOCK on Beo4, you
must first add it to the Beo4 list of functions. For
further information, refer to the chapter
‘Customise Beo4’ on page 52.
PLAY TIMER
OPTIONS
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
CONNECTIONS
SOUND
PICTURE
CLOCK
LANGUAGE
GO
select MENU
TIME
DATE
MONTH
select
GO
CLOCK
TIME
20:00
DATE
23
MONTH
APR
YEAR
2001
SYNCHRONISE
NO
SHOW CLOCK
YES
store
Abbreviations for months
Jan … January
Jul …
Feb … February
Aug …
Mar … March
Sep …
Apr … April
Oct …
May … May
Nov …
Jun … June
Dec …
July
August
September
October
November
December
GO
Adjust picture and sound settings
24
Picture and sound settings are preset
from the factory to neutral values
which suit most viewing and listening
situations. However, if you wish, you
can adjust these settings to your
liking.
Adjust picture brightness, colour or
contrast. Sound settings include
volume, bass and treble.
Store your picture and sound settings
temporarily – until your television is
switched off – or store them
permanently.
For information about how to change
the picture format, refer to the
chapter ‘Adjust sound and picture’
on page 8 in the Guide.
Change brightness, colour or contrast
Adjust the picture settings via the PICTURE
menu. Temporary settings are cancelled
when you switch off the television.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and
press to highlight PICTURE.
> Press GO to bring up the PICTURE menu.
> Press or to move through menu items.
> Press or to adjust the values.
> Press EXIT to store your settings until you
switch off the television, or …
> … press GO to store your settings permanently.
For video sources using the NTSC signal, a fourth
option – Tint (colour shade or nuance) – is
available for adjustment.
To temporarily remove the picture from the screen,
press LIST repeatedly to display P.MUTE on Beo4,
then press GO. To restore the picture again, press
any source button, such as TV.
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK
LANGUAGE
GO
select MENU
BRIGHTNESS
CONTRAST
COLOUR
select
GO
PICTURE
BRIGHTNESS
........
CONTRAST
........
COLOUR
........
TINT
........
store
GO
25
Change volume, bass or treble
Adjust the sound settings via the
SOUND SETUP menu. Temporary settings are
cancelled when you switch off the television.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and
press to highlight SOUND.
> Press GO to bring up the SOUND menu.
> Press or to move through menu items.
> Press or to adjust the values or choose a
setting.
> Press EXIT to store your settings until you switch
off the television, or …
> … press GO to store your settings permanently.
PLAY TIMER
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK
LANGUAGE
GO
select MENU
VOLUME
BALANCE
BASS
select
SOUND SETUP
VOLUME
If you connect loudspeakers or headphones …
The content of the SOUND menu varies according
to what you have connected to the television. For
further information, refer to the chapter ‘On-screen
menus’ on page 54.
GO
........
BALANCE
........
BASS
........
TREBLE
........
LOUDNESS
NO
store
GO
Choose menu language
26
The menu language you choose
during the first-time setup of your
television can be changed at any
time.
Once a menu language is chosen, all
menus and display messages are
shown in this language.
You can select the language for on-screen
menus via the TV SETUP menu. The text on
the screen changes as you move from
language to language.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
PLAY TIMER
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu and
press to highlight MENU LANGUAGE.
> Press GO to bring up the MENU LANGUAGE
menu.
> Use and to move to your language choice.
> Press GO to make your choice.
> Press STOP to back up through previous menus
or press EXIT to exit all menus directly.
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
OPTIONS
CONNECTIONS
SOUND
PICTURE
CLOCK
LANGUAGE
GO
select MENU
DANSK
DEUTSCH
ENGLISH
select
GO
MENU LANGUAGE
DANSK
DEUTSCH
ENGLISH
ESPAÑOL
FRANÇAIS
ITALIANO
NEDERLANDS
SVENSKA
select
accept
GO
Choose radio display
You can change the radio display at
any time. Your choice determines
what is shown on the screen, when
you select radio as your source.
When you change the radio display style in
the RADIO DISPLAY menu, a sample of the
display style is shown in the menu.
> Press RADIO to switch on the radio.
> Press MENU to bring up the RADIO SETUP
menu and press to highlight TUNING.
> Press GO to bring up the RADIO TUNING menu
and press to highlight RADIO DISPLAY.
> Press GO to bring up the RADIO display menu.
> Press or to change the settings.
> Press GO to store your choice.
> Press STOP to back up through previous menus
or press EXIT to exit all menus directly.
27
RADIO SETUP
TUNING
RADIO TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
RADIO DISPLAY
EDIT PROGRAMS
ADD PROGRAMS
AUTO TUNING
ADJUST DAB AERIAL
DAB DRC
select
GO
select
GO
RADIO DISPLAY
STYLE
MAXIMUM
GERNO VERSI FOLLOW EPIUM
RADIO 3
BBC CLASSIC
BBC National DAB
store
GO
28
Placement, sockets and connections
In this chapter, you can find out how
to place and connect your television.
It also gives you an overview of the
socket panels.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to
operate timed play and timed standby functions, and a connected set-top box.
We recommend that you follow the
procedure described below when
you set up your television:
– Unpack the television
– Consider the appropriate
surroundings for your television
– Mount the television on the
chosen stand or bracket
– Place the television
– Connect the cables, additional
equipment, and speakers
Tuning and preference settings, 11
This procedure is described in detail
on the following pages.
BeoLink system, 43
Find out how to set up your television for the first time and tune in programs. This
chapter also contains information about settings for time, date, stand positions,
picture and sound.
Placement, sockets and connections, 29
•
•
•
•
Set up your television, 30
Camera and headphones sockets, 33
Socket panel, 34
Connect additional video equipment, 36
Find out how to connect an audio system to your television and operate an
integrated audio/video system. Find out how to make link connections, operate a
link system and set up your television in a link room. Find out how to customise
Beo4 to your system.
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
29
Set up your television
30
For information about how to fasten
and run the cables on the rear of the
television, refer to page 32.
For further information about the
socket panel, refer to page 34.
Handling your television
– Avoid placing your television in direct sunlight
or direct artificial light, such as a spotlight, as
this may reduce the sensitivity of the remote
control receiver. Also if the screen is overheated,
black spots may appear in the picture. These
spots disappear again, once the television cools
down to normal temperature.
– To avoid injury, use Bang & Olufsen stands or
brackets only.
– Make sure that the television is set up, placed
and connected in accordance with these
instructions.
– The television is developed for indoor use in dry,
domestic environments only. Use within a
temperature range of 10–40°C (50–105°F).
– Do not place any items on top of the television.
– Always place your television on a firm and
stable surface.
– Do not attempt to open the television. Leave
such operations to qualified service personnel.
Overview of socket panels
1 Cover for fastening bracket for the optional
stand and wall bracket. Pull out at the bottom
to remove the cover.
2 Main socket panel. Refer to page 34 for further
information.
3 Cover for main socket panel. Pull out at the top
and lift to remove.
4 Cover for camera and headphones sockets.
Push in to open, push again to close.
5 Clamp for cables. It is important that the cables
are lead through the clamp and tied with a
cable tier as the cables can otherwise be tugged
free of the sockets. Refer to page 32 for further
information.
If you have a motorised stand, leave enough space
around the television to allow it to turn freely. The
television can also be turned by hand.
1
2
4
3
5
31
Placement options
The television can be placed in several ways, some
are illustrated to the right. Please contact a
Bang & Olufsen retailer for further information.
If you mount the television on one of the
motorised stands or on the wall bracket, you can
tilt the television up and down, as well as turn it
left and right. Note, however, that tilting can only
be done manually.
While mounting the television on the base, stand
or wall bracket, you can use the packaging to
support the products. This makes mounting easier.
For further information, refer to the Guide
enclosed with these accessories.
Attaching the speaker cover: Hold up the
speaker cover slightly to the right of the ‘brackets’
a and b. Now slide the cover to the left to let the
‘attach-points’ engage with the corresponding
‘brackets’ (a, b and c) on the television.
c
c
a
c
c
c
c
To remove the cover; use your thumb to push the
cover to the right to disengage it, then lift it out.
b
c
32
>> Set up your television
Aerial and mains connections
When you set the television up on its own,
simply connect the TV aerial to the TV socket
and a FM aerial to the socket marked FM and
connect the television to the mains as shown
to the right.
If your television is equipped with the
optional DAB module, you must connect a
DAB aerial also.
When using a DAB aerial …
– Use the DAB AERIAL ADJUSTMENT menu,
described on page 57, to find out where to
place your aerial. The menu lets you know how
strong the DAB signal is.
– Make sure that you hang or mount the aerial
vertically.
If you are going to connect speakers, an audio
system or any other equipment to the television,
do not connect it to the mains yet!
The supplied mains cord and plug are specially
designed for the television. If you change the plug
or in any way damage the mains cord, it will affect
the TV picture adversely!
TV
DAB
FM
When connections are complete and the cables
have been secured as described on this page,
switch on the mains. A tiny, red light appears
below the screen. The system is in standby mode
and ready to be used. If your television is set up
on its own, you can now tune in programs as
explained in the chapter ‘First-time setup of your
television’ on page 14.
Your television was designed to be left in standby
mode when not in use. Therefore, to facilitate
remote control operation, it is essential that you
do not disconnect it from the mains. The
television can only be switched off completely, if
you disconnect it from the mains.
A
B
C
IMPORTANT! All the cables must be fastened to
the television using the enclosed cable tier as
shown.
When you have made all the connections and
fastened the cables, mount the cable cover again.
Camera and headphones sockets
You can connect headphones and
listen to a programme, or you can
connect a Camcorder and watch your
home movies on the television. If you
have connected a BeoCord V 8000
video tape recorder, you can copy
Camcorder recordings onto a
videotape.
33
Sockets for temporary connections
PHONES
You can connect stereo headphones to the socket
marked PHONES. The television speakers are
muted when headphones are connected and
activated again when the headphones are
disconnected.
These sockets are for the connection of a
Camcorder:
VIDEO
For the video signal.
R–L
For audio connection (right and left sound channel
respectively).
Watch digital pictures on your television
To watch your camera pictures, connect the camera
and switch the television on. The television automatically registers the signal and you can see the
still pictures on the screen.
If the signal from the camera is switched
off …
> Press LIST repeatedly to display CAMERA on
Beo4 and press GO.
In order to display CAMERA on Beo4, you must
first add it to the Beo4 list of functions. For further
information, refer to the chapter ‘Customise Beo4’
on page 52.
PHONES
VIDEO
R
L
Watch and copy from a Camcorder
If you have connected a video tape recorder, such
as a BeoCord V 8000, to your television, and you
connect your Camcorder, you can copy Camcorder
recordings onto a videotape.
To copy a recording from a Camcorder …
> Connect your Camcorder and start playback on
the Camcorder. The television automatically
registers the signal and you can see the pictures
on the television screen.
> Press RECORD twice to start recording.
Choosing another source or switching off the television during recording from a Camcorder disrupts
recording. It is not possible to view TV programs
during recording.
Socket panel
34
The socket panel on your television
allow you to connect signal input
cables as well as a variety of extra
equipment, such as a video recorder
or a linked Bang & Olufsen music
system.
DVI
DVI connection for receiving digital or analogue
graphics from an external PC. Supports following
resolutions:
60 Hz;
640×480, 800×600, 1024×768, 1366×768.
DVI
STAND
L
AV2
AV3
AV1
R
~
Y
The AV sockets are the primary
sockets for connection of extra
equipment. Any equipment you
connect to these sockets must be
registered in the CONNECTIONS
menu. For further information, refer
to the chapter ’First-time setup of
your television’ on page 12.
Connections to the mains.
Pb
You can also connect a computer and
use your television as a monitor.
AV 2 (AV)
21-pin socket for the AV connection of other
equipment, such as a DVD player, a set-top box, a
second decoder or a game console.
The socket may be used for an AV 2 Expander
instead, which gives the opportunity to connect
other non-Bang & Olufsen video equipment at the
same time.
Pr
L
Left, line signal (for sound from PC).
MASTER LINK
DAB
TV
FM
R
Right, line signal (for sound from PC).
IROUT
POWER LINK
STAND
For connection of a motorised stand.
AV 1 (AV VMEM)
21-pin socket for the connection of a Bang &
Olufsen video recorder, a set-top box, a decoder
or another video tape recorder. You can also
connect other types of extra equipment.
MASTER LINK
Socket for connection of a compatible Bang &
Olufsen music system.
The socket is also used for BeoLink distribution of
sound throughout the house.
DAB
Aerial input socket for DAB aerial.
TV
Aerial input socket from your external aerial or
cable TV network, or from your main room
television if this television is placed in a link room.
FM
Aerial input socket from your FM aerial.
POWER LINK
For connection of external Bang & Olufsen
loudspeakers.
IR out
For a connected set-top box.
35
Computer connection
Disconnect the television, the computer, and
all equipment connected to the computer
from the mains.
Using the appropriate type of cable, connect
one end to the DVI or VGA output socket on
your computer, and the other end to the DVI
socket on the television.
To hear sound from the computer in the television speakers, use the appropriate cable and
connect the sound output on the computer
to the L – R sockets on the television.
Reconnect the television, the computer, and
all equipment connected to the computer to
the mains.
IMPORTANT! If you wish to connect a computer to
the television and use the television as a monitor,
make sure that the television, the computer, and
all equipment connected to the computer are all
disconnected from the mains before you connect
the computer and the television to each other.
In addition, the computer must be connected to a
grounded wall outlet as specified in the computer’s
setting-up instructions.
Connect additional video equipment
36
This chapter describes how to
connect additional video equipment
to the television.
Connect a decoder
BeoCenter
A decoder can be connected to the
television via the AV 2 socket. If your
setup also includes a Bang & Olufsen
video recorder, you should connect
the decoder to the video recorder.
Primary decoder
Secondary decoder
A set-top box can be connected to
any of the AV sockets.
When you connect a Bang & Olufsen
video recorder, you must connect it
to the AV 1 socket, the television
detects the connection automatically.
Make sure that all connected
equipment is registered in the
CONNECTIONS menu. For further
information, refer to the chapter
‘Register additional video equipment’
on page 40.
Disconnect all involved systems from the
mains before you connect external
equipment.
> Connect the cable from the external aerial to
the socket marked TV on the television.
> Connect the decoder to the 21-pin AV 1 socket
on the television’s socket panel.
If you wish to connect an RF decoder, connect the
external aerial cable to the decoder input socket
and then forward the signal or cable to the
television’s aerial socket (marked ‘TV IN’).
Tuned programs and decoder detection
In most cases, a connected decoder is registered
automatically during tuning. The decoder should
automatically detect those programs which
require decoding. However, if this is not the case,
then adjust the setting via the MANUAL TUNING
menu for the program in question. Please refer to
the section entitled ‘Adjust tuned TV programs’ in
the chapter ‘Edit tuned programs’ on page 18.
37
Connect a set-top box
Disconnect all involved systems from the mains
before you connect external equipment.
BeoCenter
Set-top box
> Connect one end of a 21-pin AV cable to the
set-top box.
> Run the cable to the AV 1 or AV 2 socket on the
back of the television.
> Connect the IR transmitter to the IR OUTPUT
socket on the television.
> Fasten the IR transmitter to the IR receiver of the
set-top box.
To be able to use the remote control included with
your set-top box, do not cover its IR receiver
entirely.
Automatic standby …
When you register a set-top box in the
CONNECTIONS menu, you can also select an
‘AUTO STANDBY’ time for your set-top box. This
means that you can select if the connected set-top
box should switch to standby automatically.
The options are:
AFTER 0 MIN … The set-top box switches to
standby immediately when you select another
source.
AFTER 30 MIN … The set-top box switches to
standby 30 minutes after you have selected
another source*.
AT TV STANDBY … The set-top box switches to
standby when you switch the television to
standby.
NEVER … The set-top box does not switch to
standby automatically.
FOLLOW TV … The set-top box switches on, when
you switch your television on and it switches to
standby, when you switch your television to
standby.
*If you switch the television to standby before the
30 minutes have passed, the set-top box is also
switched to standby.
Set-top boxes must be set up in accordance with
the documentation enclosed with them.
38
>> Connect additional video equipment
Connect a Bang & Olufsen recorder
Disconnect all involved systems from the mains
before you connect external equipment.
> Connect one end of a 21-pin AV cable to the AV
socket on the rear of the recorder.
> Then run the cable to the AV 1 socket on the
back of the television.
BeoCenter
Video recorder
If the connection between the television and
recorder is lost or not connected appropriately,
then CONNECTION LOST appears on the screen
when you try to program a timed recording.
Restore the connection and try again.
Aerial connection
Use your external aerial connection (or cable TV
network connection) and the aerial cable supplied
with the video recorder.
> Connect the cable from your external aerial to
on the rear
the signal input socket marked
panel of the recorder.
> Direct the aerial signal to the television, using
the aerial cable supplied with the recorder.
> Plug one end into the socket marked ‘TV’ on
the recorder and the other end into the aerial
socket marked ‘TV’ on the television’s socket
panel.
BeoCord V 8000
If you connect a BeoCord V 8000 to your television, some of the features of the BeoCord
V 8000 function differently than described in the
BeoCord V 8000 Guide, and some are not available. A supplement for the BeoCord V 8000 is
available from you Bang & Olufsen retailer.
39
Register additional video equipment
40
If you connect additional video
equipment to your television, you
must register the equipment in the
CONNECTIONS menu.
When the system is first set up, the
equipment connected at that
particular moment is detected by the
television, and the CONNECTIONS
menu appears automatically on the
screen. If you connect equipment at
a later date, on a permanent basis,
then you must register this
equipment in the CONNECTIONS
menu.
For information about where and
how to connect extra equipment,
refer to the previous pages and the
chapter ‘Socket panel’ on page 34.
What is connected?
Registering the equipment connected to the
television enables you to activate it with the
Beo4 remote control.
TV SETUP
PROGRAM GROUPS
TUNING
TIMER RECORDING
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight OPTIONS.
> Press GO to bring up the OPTIONS menu.
CONNECTIONS is highlighted already.
> Press GO to bring up the CONNECTIONS menu.
> Press or to select the AV 1 which
corresponds to your setup.
> Press to move to AV 2 and press or to
select the AV option which corresponds to your
setup.
> Press GO to store this setup.
> Press STOP to back up through previous menus
or press EXIT to exit all menus directly.
For further information about the CONNECTIONS
menu, refer to the chapter ‘On-screen menus’
on page 54.
PLAY TIMER
OPTIONS
OPTIONS
STAND POSITIONS
CONNECTIONS
SOUND
PICTURE
CONNECTIONS
SOUND
PICTURE
CLOCK
GO
select BEOLINK
MENU LANGUAGE
AV1
AV2
select
GO
store
GO
CONNECTIONS
AV1
V. MEM
AV 2
NONE
If, for some reason, you disconnect the extra
equipment and then disconnect the television from
the mains, you may have to register the equipment
again upon reconnection, even if you have not
changed your setup of extra equipment.
41
STB SETUP
NOKIA 96025
NOKIA 9820T
NOKIA 9850T
PACE DTR730-IM
SKY DIGITAL
SELECTOR
CANALdig DK/S/N
MACAB DCB-101
TPS 96573D
CANAL+ SAT r2
Planet PL 9000
CANALdigital I
ECHOSTAR 9000
CANALdigital E
TV BOX 1000-S
CANALdigital NL
NOKIA D-BOX
NOKIA D-BOX II
HUMAX F1-VACI
TechniBox CAM1
store
GO
If you have connected a set-top box, you will be
prompted to select your set-top box from an onscreen list when you select STB in the
CONNECTIONS menu.
42
BeoLink system
All your Bang & Olufsen products can
be connected in a BeoLink system. A
complete BeoLink system enables
you to distribute sound and picture
from one central source throughout
the house.
Advanced operation, 3
All you need to know about using your television beyond daily use, such as how to
operate timed play and timed standby functions, and a connected set-top box.
Tuning and preference settings, 11
Find out how to set up your television for the first time and tune in programs. This
chapter also contains information about settings for time, date, stand positions,
picture and sound.
Placement, sockets and connections, 29
Find out how to handle and place your television and where the sockets are placed.
Find out how to connect a decoder, set-top box or video recorder to your television
and how to register extra equipment.
BeoLink system, 43
•
•
•
•
Connect and operate an audio system, 44
Your television in a link room, 48
Two televisions in the same room, 51
Customise Beo4, 52
On-screen menus, 54
Overview of the on-screen menus.
Index, 62
43
Connect and operate an audio system
44
If you connect a compatible Bang &
Olufsen audio system to the
television using a Master Link cable,
you obtain the benefits of an
integrated audio/video system.
Play a CD on your audio system using
your television speakers, or switch on
a TV programme and send the sound
to your audio system speakers.
Your AV system can be placed
together in one room or in two
rooms with the television placed in
one room and the audio system with
a set of speakers placed in another.
If you disable the internal radio in
your television, it cannot be used as
source.
Not all Bang & Olufsen audio systems
support integration with the television.
Connect a radio
If you connect an audio system to your television, you must enter the BeoLink menu and
set up how the radios should be used:
OPTIONS
CONNECTIONS
SOUND
PICTURE
> Press TV to switch on the television.
> Press MENU to bring up the SETUP menu.
> Press to move to OPTIONS, press GO to call
up the OPTIONS menu.
> Press to move to BEOLINK, press GO to call
up the BEOLINK menu.
> Press or to move between the menu
options and press or to change settings.
CLOCK
BEOLINK
BEOLINK
MENU LANGUAGE
LINKED RADIO
INTERNAL RADIO
select
LINKED RADIO
YES
INTERNAL RADIO
ENABLE
GO
store
GO
45
Option setting
If your television has been set up in an AV
system, you may need to set it to the correct
Option with Beo4. Switch the entire system
to standby first.
Option setting for the television
> While holding the • button on Beo4, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
> Press LIST repeatedly to display V.OPT on Beo4
and then key in the appropriate number
(1, 2 or 4).
Option setting for the audio system
> While holding the • button on Beo4, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
> Press LIST repeatedly to display A.OPT on Beo4
and then key in the appropriate number (0, 1, 2,
5 or 6).
Option 2
Option 0
The television and an audio system set up in one
room – all speakers are connected to the television.
Option 2
Option 2
You can choose to set up your audio system in
one room, and the television (with or without
additional speakers) in another.
Option 6
If you set up your television in a link room without
an audio system, you must set it to Option 6.
Option 1
Option 1
You can choose to set up your television (with or
without additional speakers) and the audio system
(with a connected set of speakers) in the same
room.
Option 5
Option 5
If you set up your television in a link room where
an audio system is placed, you must set them to
Option 5.
46
>> Connect and operate an audio system
Use an integrated audio/video system
If you integrate your audio system and your
television, you can choose a speaker
combination appropriate to the current video
or audio program, and also record video
sound on the audio system.
Video sound recording
If you listen to sound from your television on your
Bang & Olufsen audio system’s speakers, and your
audio system has a tape recorder, you can record
television sound on the audio tape recorder. Refer
to the Guide enclosed with your audio system for
further information.
The setups described on this page illustrate which
radio is activated when you have enabled the
internal radio and connected a link radio to your
television also.
LIST
TV
AV
LIST
TV
AV
TV
To listen to sound from a television source on your
audio system speakers without switching on the
screen, press LIST repeatedly to display AV* on
Beo4, and then press a source button, such as TV.
LIST
AV
CD
To listen to audio sound on the television speakers,
press LIST repeatedly to display AV* on Beo4, and
then press an audio source button, such as CD.
*In order to display AV on Beo4, you must first add
it to the Beo4 list of functions. For further
information, refer to the chapter ‘Customise Beo4’
on page 52.
To listen to sound from television on your audio
system speakers with the screen switched on,
press TV, press LIST repeatedly to display AV*, and
then press TV again.
47
Your television in a link room with an audio system
If you set up your television in a link room
and enable the internal radio, you can choose
which radio you want to listen to. However,
you can only use the internal radio in your
television, if you have enabled it, as
described on page 46.
Option 5
Option 5
LIST
RADIO
AV
RADIO
To listen to radio from the audio system, simply
press RADIO.
To listen to radio from the built in radio, press LIST
repeatedly to display AV* on Beo4, then press
RADIO.
Your television in a link room
48
If you have BeoLink installed in your
home and you choose to place your
television in a link room, you can
operate all connected systems
through the television.
You must follow the procedure described
below when you connect your television
for use in a link room:
1 Connect the link room television to the
mains
2 Using the Beo4 remote control,
program the link room television to
Option 6*
3 Disconnect the link room television
from the mains
4 Make the link and aerial connections
5 Reconnect the link room television to
the mains.
Option setting
For your entire system to function properly, it
is essential that the television in the link
room is set to the correct Option before you
connect it to the system in the main room!
To set the link room television to the correct
option …
> While holding the • button, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
> Press LIST repeatedly to display V.OPT on Beo4
and press 6*.
Main room
Link room
Option 6*
*If you connect the television for use in a link
room where other link systems are already
connected, such as speakers, you must set the
television to Option 5 instead.
49
Link frequency
If you change the link frequency in the main
room system, make sure that the link
frequency in the link room system
corresponds to it.
TV SETUP
PROGRAM GROUPS
TUNING
TV TUNING
TIMER RECORDING
EDIT PROGRAMS
PLAY TIMER
To change the link frequency …
> Press TV to switch on the television.
> Press MENU to bring up the TV SETUP menu
and press to highlight TUNING.
> Press GO to bring up the TV TUNING menu and
press to highlight LINK FREQUENCY.
> Press GO to bring up the LINK FREQUENCY
menu. FREQUENCY is already highlighted.
> Press or to find the frequency.
> Press GO to store the setting, or …
> … press EXIT to leave all menus without
storing.
ADD PROGRAM
OPTIONS
AUTO TUNING
STAND POSITIONS
MANUAL TUNING
LINK FREQUENCY
EDIT PROGRAM
ADD PROGRAM
AUTO TUNING
FREQUENCY
select
GO
select
GO
LINK FREQUENCY
FREQUENCY
599
search
store
GO
50
>> Your television in a link room
Link room operation
When you are in the link room, you can
operate all connected systems with the Beo4
remote control.
Use sources present only in
one of the rooms …
Press the button for the source
you wish to use
RADIO
Press the button for the source
you wish to use
Operate the source as usual
Main room
Link room
TV
Operate the source as usual
Listen to stereo sound in your
link room …
Usually sound distributed from a
main room video source, such as
a set-top box, to the link room is
transmitted in mono. However,
you can select stereo sound:
Operate the selected source as
usual
Use a main room source –
source type present in both
rooms …
Press repeatedly on Beo4 until
LINK* is shown in the Beo4
display
Use a link room source –
source type present in both
rooms …
Press the button for the source
you wish to use
LIST
LINK
TV
Press to switch on the television
TV
Press repeatedly until AV* is
shown in the Beo4 display
LIST
Press to activate a source
connected to the main room
system, such as a set-top box
DTV
While using this function,
distribution of other main room
sources to other link room
systems is not possible.
AV
*In order to display LINK and AV on Beo4, you
must first add them to the Beo4 list of functions.
For further information, refer to the chapter
‘Customise Beo4’ on page 52.
Two televisions in the same room
If you have placed your BeoCenter 6
in a room where you already have a
Bang & Olufsen television, and
commands from Beo4 can be
received by both televisions, you
must change the option setting of
BeoCenter 6. This prevents
simultaneous activation of both
televisions.
51
One remote control for both televisions
For your television to function properly, it is
essential that the television is set to the
correct Option:
To set your television for Option 4 …
> While holding the • button on Beo4, press LIST.
> Let go of both buttons.
> Press LIST repeatedly to display OPTION? on
Beo4 and press GO.
> Press LIST repeatedly to display V.OPT on Beo4
and press 4.
Operate your television in Option 4 …
Normally, you can activate a source, such as
TV, simply by pressing the relevant source
button on Beo4. However, when you set your
television to Option 4, you must do the
following:
> Press LIST repeatedly until LINK* is shown in the
Beo4 display.
> Press a source button, such as TV.
*In order to display LINK on Beo4, you must add it
to the Beo4 list of functions.
BeoCenter 6
Option 4
LIST
LINK
TV
TV
In order to use teletext on a television you have set
to Option 4, you must set up Beo4 to ‘VIDEO 3’,
but this limits the Beo4 functions that can be used
with televisions set to other Options. For further
information refer to the chapter ‘Customise Beo4’
on page 52.
Customise Beo4
52
The Beo4 buttons give direct remote
control of a large number of
television functions, and the Beo4
display gives you access to even more
functions.
Set up Beo4
Add an extra ‘button’
The Beo4 is set up for use with BeoCenter 6
from the factory. However, if you buy a new
Beo4 you can set this up for your television
also.
When you add a new function to the Beo4
list, you can then bring up this new ‘button’
in the Beo4 display.
Press and hold the standby
button down
•
Press and hold the standby
button down
•
Whenever a source is displayed on
Beo4 (TV, RADIO, etc.), you can press
the LIST button and bring up extra
functions in the display to help you
operate that source, just as if you
were calling up extra buttons. You
can also switch on extra equipment
connected to your television.
LIST
Press to get access to the Beo4
setup function
LIST
Press to get access to the Beo4
setup function
You can customise a new Beo4 to
suit your television, and change the
order in which these extra functions
appear when you call them up.
Note that Beo4 contains a list of all of
Bang & Olufsen’s extra audio and
video functions, but only those
functions supported by the television
work when you call them up in the
Beo4 display.
Let go of both buttons. ADD?
appears in the display
ADD?
Press repeatedly to display
CONFIG? on Beo4
LIST
Press to be able to select the
type of configuration
GO
Press repeatedly to display
VIDEO? on Beo4
LIST
Press to get access to the video
configuration
GO
Press repeatedly to display
VIDEO 2 on Beo4*
LIST
Press to store the configuration
GO
STORED appears, indicating that
the configuration has been
stored. You leave the Beo4 setup
function automatically
*If you have set your television
to Option 4, select ‘VIDEO 3’.
CONFIG?
Let go of both buttons. ADD?
appears in the display
Press to bring up the list of
available ‘buttons’ to add from.
The first ‘button’ appears in the
display, it flashes on and off
ADD?
GO
Press to move forwards or
backwards in the list of all extra
‘buttons’
VIDEO?
VIDEO 2
STORED
Press to add and place the
‘button’ on its preset position or
as the first ‘button’ in the list,
or …
GO
… press to insert the ‘button’ at
a specific position in the list
1–9
ADDED appears, indicating that
the ‘button’ has been added.
You leave the Beo4 setup
function automatically
ADDED
53
Move extra ‘buttons’
Remove an extra ‘button’
You can rearrange the order in which the
extra ‘buttons’ appear when you press LIST.
You can remove any of the extra ‘buttons’
that are available when you press LIST.
Press and hold the standby
button down
•
Press and hold the standby
button down
•
Press to get access to the Beo4
setup function
LIST
Press to get access to the Beo4
setup function
LIST
GO
Let go of both buttons. ADD?
appears in the display
ADD?
Press repeatedly to display
MOVE? on Beo4
LIST
Press to bring up the list of extra
‘buttons’. The first ‘button’
appears in the display
GO
MOVE?
Press to move forwards or
backwards in the list of extra
’buttons’
ADD?
Press repeatedly to display
REMOVE? on Beo4
LIST
Press to bring up the list of extra
‘buttons’. The first ‘button’
appears in the display
GO
REMOVE?
Add an extra ‘button’ to Beo4, either to the top of
the list or to a specific position.
Press to move forwards or
backwards in the list of extra
’buttons’
Press to move and place the
displayed ‘button’ as the first in
the list, or …
GO
… press to move the ‘button’ to
a specific position in the list
1–9
MOVED appears, indicating that
the ‘button’ has been moved.
You leave the Beo4 setup
function automatically
Let go of both buttons. ADD?
appears in the display
Press to remove the ‘button’
shown in the display
REMOVED appears, indicating
that the ‘button’ has been
removed. You leave the Beo4
setup function automatically
3
GO
REMOVED
GO
3
MOVED
Move extra ‘buttons’, either to the top of the list
or to a specific position.
On-screen menus
54
In order for you to find your way
through the on-screen menus your
television offers, this chapter
illustrates the overall structure of the
menu system.
The chapter also gives you detailed
information about the individual
menus.
PROGRAM AND STATION GROUPS
OPTIONS
CONNECTIONS
TV TUNING
EDIT PROGRAMS
ADD PROGRAMS
AUTO TUNING
MANUAL TUNING
EXTRA
FINE TUNE
DECODER
TV SYSTEM
SOUND
RADIO TUNING
AV1
AV2
SOUND
VOLUME
BALANCE
BASS
TREBLE
LOUDNESS NO/YES
PICTURE
BRIGHTNESS
CONTRAST
EDIT PROGRAMS
COLOUR
ADD PROGRAMS
TINT
AUTO TUNING
CLOCK
MANUAL TUNING
TIME
RADIO DISPLAY
DATE
ADJUST DAB AERIAL
MONTH
DAB DRC
YEAR
LINK FREQUENCY
FREQUENCY
PLAY TIMER
SYNCHRONISE
MENU LANGUAGE
DANSK
DEUTSCH
TIMER ON/OFF
ENGLISH
TIMER INDEX
ESPAÑOL
PLAY TIMER PROGRAMMING
FRANÇAIS
SOURCE
ITALIANO
PROGRAM/STATION
NEDERLANDS
START TIME
SVENSKA
STOP TIME
DAYS
WAKE UP TIMER
STAND POSITIONS
VIDEO
AUDIO
STANDBY
The extended on-screen menu system for the
television. The presence of the greyed menu items
depends on whether these optional extras are
available in your system.
Press MENU on Beo4 to access the main menu.
55
PROGRAM GROUPS
EDIT TV PROGRAMS
1
2
3
4
5
6
7
8
9
..
..
17
18
GROUP1
...
...
...
...
...
...
...
name
new group
move
create group
GO
What’s on the PROGRAM GROUPS menu …
You can create program Groups, name them and
copy individual TV programs into the Groups.
For further information, refer to the chapter ‘Use
Groups’ on page 12 in the Guide.
DR1
TV2
........
EUROSPRT
ZDF
RTL7
........
BBC
........
ADD TV PROGRAM
10
11
12
13
14
15
16
17
18
19
........
........
CNN
N3
........
SAT 1
SVT 2
NRK
TV4
........
NRK
TV4
more
name
move
What’s on the EDIT PROGRAMS menu …
When the EDIT PROGRAMS menu appears on the
screen you have several options: You can move
the programs to change the order in which they
appear in the lists. You can delete unwanted
programs and you can name or rename your
programs.
For further information, refer to the chapter ‘Edit
tuned programs’ on page 15.
start
What’s on the ADD PROGRAM menu …
The ADD PROGRAM function is automatic. When
tuning of additional programs is complete, the
EDIT PROGRAMS menu appears automatically.
56
>> On-screen menus
TV MANUAL TUNING
TV AUTO TUNING
1
........
TV MANUAL TUNING
SEARCH
...
FINE TUNE
0
FREQUENCY
210
DECODER
OFF
PROGRAM NUMBER
1
TV SYSTEM
B/G
NAME
DR1
SOUND
STEREO
EXTRA
DELETES PROGRAM GROUPS
start
What’s on the AUTO TUNING menu …
The AUTO TUNING function is automatic. When
tuning of all programs is complete, the EDIT
PROGRAMS menu appears.
start
store
GO
What’s on the TV MANUAL TUNING menu …
SEARCH … Start search tuning.
FREQUENCY … Select a frequency to tune in.
PROGRAM NUMBER … Store or change program
number. You can store 99 programs.
NAME … Access the naming menu and name the
program you have selected.
EXTRA … Access the extra TV MANUAL TUNING
menu.
accept
GO
What’s on the extra TV MANUAL TUNING
menu …
FINE TUNE … Fine tune the frequency of a
program or tuned program. You can fine tune
within the range of -8 – +8.
(DECODER) … A decoder is necessary for the
reception of coded programs. Usually the
decoder is detected automatically during tuning,
but it can be selected via this menu option. Set
DECODER to one of following options: ON (for
decoder on) or OFF (for no decoder).
(TV SYSTEM) … TV broadcast system – this option
is only available on certain types of TV sets, as
the TV broadcast system is usually selected
automatically.
SOUND (mono, stereo or language) … Several
types of sound may be available for different
programs, mono, stereo or different languages.
On the relevant program or frequency select the
options MONO (FM / NICAM mono sound),
STEREO (NICAM / A2 stereo sound), MONO1
(mono language 1), MONO2 (mono language 2),
MONO3 (mono language 3), or STEREO2 (stereo
language 2).
Even though you store a type of sound/language,
you can switch between the various types while
watching a TV programme. For further information,
refer to the chapter ‘Adjust sound and picture’ on
page 8 in the Guide.
57
RADIO MANUAL TUNING
RADIO MANUAL TUNING
FM / DAB
FM
FM / DAB
DAB
SEARCH
92.6
SEARCH
...
CHANNEL
12 C
FREQUENCY
...
PROGRAM NUMBER
10
NAME
STRUER
FINE TUNE
0
SOUND
STEREO
ADJUST DAB AERIAL
..............................................................
DR DAB
CHANNEL
12 C
DR DAB
store
GO
What’s on the FM RADIO TUNING menu …
FM/DAB … Choose between FM and DAB*.
SEARCH … Start searching the frequency band up
or down.
FREQUENCY … Select a frequency to tune in.
PROGRAM NUMBER … Store or change program
number. You can store 99 programs.
NAME … Access the naming menu and name the
program you have selected.
FINE TUNE … Fine tune the frequency of a
program or tuned program. You can fine tune
within the range of -4 – +8.
SOUND … Choose between stereo or mono. The
receiver will switch automatically to Mono
sound if the Stereo signal is affected by noise.
PROGRAM
DR SOFT
PROGRAM NUMBER
10
NAME
DR SOFT
store
GO
What’s on the DAB RADIO TUNING menu …
FM/DAB … Choose between FM and DAB*.
SEARCH … Start searching the frequency band up
or down.
CHANNEL … Select a channel to tune in. Enter
the channel number by means of the number
buttons, change between letters by means of
the arrow buttons left and right.
(ENSEMBLE) … This field informs you of the found
ensemble, no selection can be made here.
PROGRAM … Choose between different
programs within the found ‘ensemble’.
PROGRAM NUMBER … Store or change program
number. You can store 99 programs.
NAME … Access the naming menu and name the
program you have selected.
*Receiving DAB radio programs is only possible if
your television is equipped with the optional DAB
module and DAB radio is transmitted in your area.
What’s on the ADJUST DAB AERIAL* menu …
When an ‘ensemble’ has been found, this menu
can be used to optimise signal reception.
The bar at the top of the menu shows the
reception quality.
If no ensembles have been found, you can enter a
channel number by means of the number buttons,
change between letters by means of the arrow
buttons left and right, and then move the DAB
aerial until an ‘ensemble’ name appears in the
menu.
58
>> On-screen menus
RADIO DISPLAY
DYNAMIC RANGE CONTROL MENU
OFF
MIDDLE
MAX
STYLE
TV RECORD
MAXIMUM
NOW
TELETEXT
...........................................................................
RECORD LIST
??? TEXT TEXT TEXT ???
MENU
RADIO 3
BBC CLASSIC
BBC National DAB
BBC
store
GO
What’s on the DYNAMIC RANGE CONTROL
menu …
For certain DAB programs, you can adjust audio
signal compression with the DRC (Dynamic Range
Control) function. Compression compensates for
sources of noise in your immediate surroundings.
There are twelve possible settings, with three
values to guide you:
OFF (no compression)
MIDDLE (recommended by the DAB provider)
MAX (maximum compression, twice that
recommended by the DAB provider).
DAB DRC menu settings have no effect for
programs not broadcast with DRC.
store
GO
What’s on the RADIO DISPLAY menu …
STYLE … Select the display settings for when you
listen to radio. Options are:
MAXIMUM … Shows text sent out by the
broadcaster continuously, as well as radio
program number, name of the radio program,
frequency or ‘ensemble’ name.
TIME OUT … Shows the maximum display but
removing the display when the text sent out by
the broadcaster has been shown once.
MINIMUM … Shows the radio program number
and the name of the radio program.
OFF … No display in radio mode.
select
GO
What’s on the TV RECORD menu …
NOW … Use this option to make an instant
recording. Alternatively, press RECORD twice to
make an instant recording.
TELETEXT … Use this option to make a timed
recording via teletext.
RECORD LIST … Use this option to check or delete
your recordings.
MENU … Use this option to make a timed
recording via the recording menu.
This menu is only available if a BeoCord V 8000 is
connected to your television.
Some of the features of the BeoCord V 8000
function differently with this television than
described in the BeoCord V 8000 Guide, and
some are not available. A supplement for the
BeoCord V 8000 Guide is available from your
Bang & Olufsen retailer.
59
TIMER PROGRAMMING
SOURCE
STAND POSTIONS
WAKE UP TIMER
VIDEO
TV
SOURCE
PROGRAM
18 BBC
PROGRAM
21 BBC
START TIME
15:40
START TIME
07:00
STOP TIME
16:40
ON / OFF
ON
DAYS
M . . TF . S
TV
AUDIO
STANDBY
...
store
GO
What’s on the TIMER PROGRAMMING
menu …
SOURCE
Choose the source for your Timer from the
available sources in your system. Choose
STANDBY, if you want the television to switch
off. If you have other compatible video or audio
systems connected to your television, they are
switched off as well.
PROGRAM (Program number) … Once your
source is chosen, choose the program number
you want.
START TIME and STOP TIME … Key in the times
when you want the system to start and/or stop
playing. If you have set the Timer source to
STANDBY, it is only possible to enter a stop time.
DAYS … Select the specific weekday(s) on which
you want your Timer executed. All the
weekdays will be displayed – starting with M for
Monday.
store
GO
What’s on the WAKE-UP TIMER menu …
SOURCE … Choose the source for your Wake-up
Timer from the available sources in your system.
PROGRAM (Program number) … Choose the
program number you want.
START TIME … Key in the time when you want
the system to start playing.
ON/OFF … Activate or deactivate your Wake-up
Timer. Choose ON to activate and OFF to
deactivate.
select
GO
What’s on the STAND POSITIONS menu …
VIDEO … Select the position you want the
television to turn to when you switch on a video
source.
AUDIO … Select the position you want the
television to turn to when you switch on an
audio source*.
STANDBY … Select the position you want the
television to turn to when it is switched off.
*This only applies if no external speakers are
connected to the television.
This menu is only available if your television is
equipped with an optional motorised stand.
You can only use a source, such as A.MEM, if it is
present in your setup.
NOTE! Remember to activate your Timer by
setting TIMER PLAY to ON, if you want the Timer
to apply to the television.
60
>> On-screen menus
CONNECTIONS
SOUND SETUP
PICTURE
AV1
V. MEM
VOLUME
........
BRIGHTNESS
AV 2
NONE
BALANCE
........
CONTRAST
........
BASS
........
COLOUR
........
TREBLE
........
LOUDNESS
ON
store
GO
What’s on the CONNECTIONS menu …
AV 1
NONE … if no equipment is connected.
V.MEM … if you have connected a Bang &
Olufsen video recorder or any other video
recorder.
V.MEM+DECODER … if you have connected a
Bang & Olufsen video recorder with a decoder
connected to it.
V.MEM+STB … if you have connected a Bang &
Olufsen video recorder with a set-top box
connected to it.
DECODER … if you have connected a decoder.
V.AUX … if you have connected any other type
of auxiliary equipment.
STB … if you have connected a set-top box.
If you connect a Bang & Olufsen video recorder,
the only options for V.TAPE are: V.MEM,
V.MEM+STB and V.MEM+DECODER.
AV 2
NONE … if no equipment is connected.
EXPANDER … if you have connected an
Expander box with other auxiliary equipment
connected to it.
V.AUX … if you have connected any other type
of auxiliary equipment.
DVD … if you have connected a DVD player or
similar devices.
STB … if you have connected a set-top box.
store
GO
What’s on the SOUND SETUP/SOUND
ADJUSTMENT menu …
VOLUME … Adjusts the volume level the TV uses
when you switch it on.
(CENTRE) … Only available if you have connected
loudspeakers to the television. Adjusts the
balance between the external and internal
speakers.
(BALANCE) … Adjusts the balance between the
speakers.
BASS … Adjusts the bass level.
TREBLE … Adjusts the treble level.
LOUDNESS … The loudness feature compensates
for the human ear’s lack of sensitivity to high
and low frequencies. These frequencies are
boosted at low volume levels so that low music
becomes more dynamic. Loudness can be set to
ON or OFF.
The contents of this menu varies according to your
speaker setup.
........
store
GO
What’s on the PICTURE menu …
BRIGHTNESS … Adjusts the picture brightness.
CONTRAST … Adjusts the contrast level in the
picture.
COLOUR … Adjusts the colour intensity in the
picture.
For video sources using the NTSC signal, a fourth
option – Tint (colour shade or nuance) – will be
available for adjustment.
61
CLOCK
MENU LANGUAGE
DVI SETUP
TIME
20:00
DANSK
BRIGHTNESS
31
DATE
23
DEUTSCH
CONTRAST
31
MONTH
APR
ENGLISH
COLOUR
31
YEAR
2001
ESPAÑOL
SYNCHRONISE
YES
FRANÇAIS
SHOW CLOCK
YES
ITALIANO
NEDERLANDS
SVENSKA
store
GO
What’s on the CLOCK menu …
TIME … Indicates the time.
DATE … Indicates the day.
MONTH … Indicates the month.
YEAR … Indicates the year.
SYNCHRONISE … For synchronisation of the builtin clock with teletext.
SHOW CLOCK … Select YES if you want the time
to be shown permanently on the screen.
select
accept
GO
What’s on the MENU LANGUAGE menu …
Choose between the available languages.
What’s on the DVI SETUP menu …
BRIGHTNESS … Adjusts the picture brightness.
CONTRAST … Adjusts the contrast level in the
picture.
COLOUR … Adjusts the colour intensity in the
picture.
This menu is only available, if you have connected
a computer to the television via the DVI socket.
62
Index
Beo4 remote control
Contact
Add a ‘button’ to the Beo4 list, 52
Changing the Beo4 batteries, Guide p. 18
Cleaning the Beo4, Guide p. 18
Configure Beo4, 52
Customise Beo4, 52
Introducing your television and Beo4,
Guide p. 4
Move extra ‘buttons’, 53
Remove a ‘button’ from the Beo4 list, 52
Replace Beo4 batteries, Guide p. 18
Using Beo4, Guide p. 4
Contact Bang & Olufsen, Guide p. 19
BeoLink
Link frequency, 49
Link room operation, 50
Master Link socket, 34
Your television in a link room, 48
Camera
Connect a Camera, 33
Copy from a Camcorder to a videotape, 33
Clock
Set the time and date, 23
What’s on the CLOCK menu, 61
Computer monitor
Adjust picture, 5
Bring up the computer image on the screen, 5
Connect a computer, 35
What’s on the DVI menu, 61
Connections
Aerial and mains connection, 32
Audio system – connect to the television, 44
BeoCord V 8000 video tape recorder, 38
Camera, 33
Connections – your television in a link
room, 48
Decoder, 36
Headphones, 33
Link room connections, 48
Loudspeakers, 34
Register additional video equipment, 40
Set-top box, 37
Socket panel, 34
Sockets for temporary connections, 33
What’s on the CONNECTIONS menu, 60
Decoder
Connect a decoder, 36
Displays and menus
Displayed information and menus, Guide p. 5
On-screen menus, 54
DAB radio
Add new TV or radio programs, 21
Adjust tuned DAB programs, 19
Auto-tuning – first-time setup of your
television, 12
Bring up a list of radio programs, Guide p. 14
Delete tuned programs, 16
Edit tuned programs, 19
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
See list of all programs, Guide p. 14
What’s on the ADJUST DAB AERIAL menu, 57
What’s on the DAB DRC menu, 58
What’s on the PROGRAM GROUPS menu, 55
What’s on the RADIO DISPLAY menu, 58
What’s on the RADIO MANUAL TUNING
menu, 57
First-time setup
First-time setup procedure, 12
Format
Change the picture format, Guide p. 9
Groups
Create Groups, Guide p. 12
Move programs within a Group, Guide p. 13
Select programs in a Group, Guide p. 12
What’s on the PROGRAM GROUPS menu, 55
Headphones
Connect headphones, 33
63
Language
Position of television
Stand
Change sound type or language, Guide p. 8
Choose menu language, 26
First-time setup – choose menu language, 12
What’s on the MENU LANGUAGE menu, 61
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Determine the centre position – first-time
setup, 14
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Loudspeakers
Change speaker balance or combination,
Guide p. 9
Connect speakers, 34
Sound adjustments, 24
What’s on the SOUND ADJUSTMENT
menu, 60
Maintenance
About the screen, Guide p. 18
Change Beo4 batteries, Guide p. 18
Handling your television, 30
Maintenance of your television, Guide p. 18
Master Link
Audio system with your television, 44
Connect your audio system, 34
Option setting, 45
Use integrated audio/video system, 46
Picture
Adjust brightness, colour or contrast, 24
Change the picture format, Guide p. 9
Remove the picture from the screen, 24
What’s on the PICTURE menu, 60
Pincode
Activate the pincode system, Guide p. 16
Change or delete your pincode, Guide p. 16
If you have forgotten your pincode, Guide
p. 17
Use your pincode, Guide p. 17
Placement
Set up your television, 30
Set positions for the television to turn to, 22
Turn the television, Guide p. 7
What’s on the STAND POSITIONS menu, 59
Radio
Add new TV or radio programs, 21
Adjust tuned radio programs, 19
Auto-tuning – first-time setup of your
television, 12
Bring up a list of radio programs, Guide p. 14
Delete tuned programs, 16
Edit tuned programs, 19
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
Listen to tuned programs, Guide p. 14
See list of all programs, Guide p. 14
What’s on the PROGRAM GROUPS menu, 55
What’s on the RADIO DISPLAY menu, 58
What’s on the RADIO MANUAL TUNING
menu, 57
Subtitles
Subtitles from teletext, Guide p. 11
Teletext
Basic teletext functions, Guide p. 10
Day-to-day use of MEMO pages, Guide p. 11
Store favourite teletext pages, Guide p. 11
Timer
Set the television to switch itself on and off, 6
Set the time and date, 23
Timed play and timed standby, 6
View, edit or delete a Timer, 7
Set-top box
Tune
Connect a set-top box, 37
Set-top Box Controller menu, 8
Universal Beo4 operation, 9
Use the set-top box in a link room, 9
Use the set-top box’s own menu, 9
Add new radio or TV programs, 21
Adjust tuned programs, 18
Auto-tuning – first-time setup of your
television, 13
Delete tuned programs, 16
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
What’s on the ADD PROGRAMS menu, 55
What’s on the AUTO TUNING menu, 56
What’s on the extra TV MANUAL TUNING
menu, 56
What’s on the RADIO MANUAL TUNING
menu, 57
What’s on the TV MANUAL TUNING menu, 56
Socket panel
Camera and headphones sockets, 33
Socket panel, 34
Sound
Adjust or mute the sound, Guide p. 8
Adjust volume, bass or treble, 25
Change sound type or language, Guide p. 8
Change speaker balance or combination,
Guide p. 9
What’s on the SOUND ADJUSTMENT
menu, 60
64
>> Index
TV programs
Add new TV programs, 21
Adjust tuned programs, 18
Auto-tuning – first-time setup of your
television, 13
Bring up a TV list, Guide p. 6
Delete tuned programs, 16
Edit tuned programs, 15
Move tuned programs, 16
Name tuned programs, 17
Re-tune via automatic tuning, 20
Select a TV program, Guide p. 6
What’s on the ADD PROGRAMS menu, 55
What’s on the AUTO TUNING menu, 56
What’s on the EDIT PROGRAMS menu, 55
What’s on the extra TV MANUAL TUNING
menu, 56
What’s on the PROGRAM GROUPS menu, 55
What’s on the TV MANUAL TUNING menu, 56
Wake-up Timer
Enter a Wake-up Timer, 4
Check or delete a Wake-up Timer, 4
Set the time and date, 23
65
66
Waste Electrical and Electronic Equipment
(WEEE) – Environmental protection
The European Parliament and the Council of the
European Union have issued the Waste Electrical
and Electronic Equipment Directive. The purpose of
the Directive is the prevention of waste of electrical
and electronic equipment, and to promote the reuse
and recycling and other forms of recovery of such
waste. As such the Directive concerns producers,
distributors and consumers.
The WEEE directive requires that both manufacturers
and end-consumers dispose of electrical and
electronic equipment and parts in an environmentally
safe manner, and that equipment and waste are
reused or recovered for their materials or energy.
Electrical and electronic equipment and parts must
not be disposed of with ordinary household refuse;
all electrical and electronic equipment and parts
must be collected and disposed of separately.
Products and equipment which must be collected
for reuse, recycling and other forms of recovery are
marked with the pictogram shown.
This product fulfils the conditions stated
in the EEU directives 89/336 and 73/23.
Technical specifications, features and the use
thereof are subject to change without notice.
3507804
0710
When disposing of electrical and electronic equipment by use of the collection systems available in
your country, you protect the environment, human
health and contribute to the prudent and rational
use of natural resources. Collecting electrical and
electronic equipment and waste prevents the
potential contamination of nature with the
hazardous substances which may be present in
electrical and electronic products and equipment.
Your Bang & Olufsen retailer will assist with and
advise you of the correct way of disposal in your
country.
Small products may not always be marked with
the pictogram in which case this is present in the
instructions for use, on the guarantee certificate
and printed on the packaging.
www.bang-olufsen.com
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement