Safety Test Report KISS 2U KTQ87

Safety Test Report KISS 2U KTQ87
Test Report issued under the responsibility of:
TEST REPORT
IEC 60950-1
Information technology equipment – Safety –
Part 1: General requirements
Report Number. .............................. :
18005046 001
Date of issue .................................... :
2014-06-18
Total number of pages ......................
94
CB Testing Laboratory................... :
TÜV Rheinland Singapore Pte. Ltd., Laboratory
Address ............................................ :
25, International Business Park, #04-03/04, German Centre,
Singapore 609916
Applicant’s name............................ :
Kontron Europe GmbH
Address ............................................ :
Sudetenstraße 7
87600 Kaufbeuren, Germany
Manufacturer’s name……………….: Kontron Europe GmbH
Address ............................................ :
Sudetenstraße 7
87600 Kaufbeuren, Germany
Test specification:
Standard ........................................... :
IEC 60950-1:2005 (Second Edition) + Am 1:2009
Test procedure ................................. :
CB Scheme
Non-standard test method…………..:
N/A
Test Report Form No...................... :
IEC60950_1C
Test Report Form(s) Originator ........ :
SGS Fimko Ltd
Master TRF ...................................... :
Dated 2012-08
Copyright © 2012 Worldwide System for Conformity Testing and Certification of Electrotechnical
Equipment and Components (IECEE), Geneva, Switzerland. All rights reserved.
This publication may be reproduced in whole or in part for non-commercial purposes as long as the IECEE is acknowledged as
copyright owner and source of the material. IECEE takes no responsibility for and will not assume liability for damages resulting
from the reader's interpretation of the reproduced material due to its placement and context.
If this Test Report Form is used by non-IECEE members, the IECEE/IEC logo and the reference to the
CB Scheme procedure shall be removed.
This report is not valid as a CB Test Report unless signed by an approved CB Testing Laboratory
and appended to a CB Test Certificate issued by an NCB in accordance with IECEE 02.
TRF No. IEC60950_1C
Page 2 of 94
Report No. 18005046 001
Test item description .....................:
Industrial computer
Trade Mark ....................................... :
kontron
Manufacturer .................................... :
See above
Model/Type reference ...................... :
KISS 2U V2 KTQ87-A
Ratings ............................................. :
100-240 Vac, 4.5A max, 50-60 Hz
TRF No. IEC60950_1C
Page 4 of 94
Report No. 18005046 001
List of Attachments (including a total number of pages in each attachment):
- Photo Documentation (total 14 pages)
Summary of testing:
Test sample(s): Production sample with serial number: 123456789
A sample of the equipment was subject of a construction check.
1) All tests were performed at normal load condition unless otherwise specified.
2) All tests were performed at minimum and/or maximum input voltage range specified by manufacturer
and were basically reported whichever worse result.
3) All relative tests were performed as using the software provided by manufacturer. This is Pass-mark
burn-in test software which continuously sending and receiving USB, Display port, LAN, audio signals in
and out.
Tests performed (name of test and test clause):
All applicable tests as described in Test Case and
Measurement Sections were performed.
Clause
Testing location:
(see “testing procedure and testing location“ on the
previous page)
Test description
Applicable
Comments
(Yes/No)
1.6.2
Input current
Yes
2.1.1.5
Energy hazards
No
2.1.1.7
Discharge of capacitors in equipment
No
2.1.1.8
Energy hazards – d.c. mains supply
No
2.2.2
SELV/Voltage measurement under normal
condition
No
Evaluated by approved
power supply
2.2.3
SELV/Voltage measurement under fault
conditions
No
Evaluated by approved
power supply
2.3.5
Operating voltages generated externally
No
2.4.2
Limited current circuits
No
2.5
Limited power sources
Yes
2.6.3.4
Resistance of earthing conductors and their
terminations
Yes
2.9.2
Humidity conditioning
Yes
48 h, 93%RH, 25’C
2.10
Creepage and Clearances, Distance through
Insulation
No
Evaluated by approved
power supply
2.10.2.2/
Determination of working voltage
No
Evaluated by approved
power supply
TRF No. IEC60950_1C
Evaluated by approved
power supply
Evaluated by approved
power supply
Evaluated by approved
power supply
Output ports (USB, display
port) of motherboard tested
32A, 2 min and 40A, 2 min
tested
Page 5 of 94
Report No. 18005046 001
2.10.2.3
2.10.5
Solid insulation
Yes
2.10.12
Enclosed and sealed parts
No
3.2.6
Cord anchorages and strain relief
No
4.1
Stability
Yes
4.2
Mechanical strength
Yes
4.3.6
Direct plug-in equipment
No
4.3.13
Radiation
No
4.5.2
Maximum Temperatures
Yes
4.5.5
Resistance to abnormal heat
Yes
5.1
Touch current and protective conductor
current
Yes
5.2
Electric strength
Yes
5.3
Abnormal operating and fault conditions
Yes
6.1.2
Separation of the telecommunication network
from earth
No
6.2
Protection of equipment users from
overvoltages on telecom. Networks
No
6.3
Protection of the telecommunication wiring
system from overheating
No
7.2
Protection of equipment users from
overvoltages on cable distribution system
No
7.3
Insulation between primary and cable
distribution system
No
Annex A
Resistance to heat and fire
No
Annex B
Locked-rotor overload test
Yes
Front system fan, CPU fan
Annex C
Overload test
No
Evaluated by approved
power supply
Annex G
Determining minimum clearances
No
Annex H
Ionizing radiation
No
Annex K
Thermal controls
No
Annex M
Criteria for telephone ringing signals
No
Annex Q
Voltage dependent resistors (VDRs)
No
Annex U
Insulated wire for use without interleaved
No
TRF No. IEC60950_1C
A laser measurement test
report reference number
12CA14583, tested for IEC
60825-1: 2007 clause 8 and
9 by UL Japan, Inc.
CPU fan frame is tested
Pri toPE, Pri to Sec
Evaluated by approved
power supply
Page 6 of 94
Report No. 18005046 001
insulation
Annex Y
Ultraviolet light conditioning test
No
Annex CC
Evaluation of Integrated circuit (IC) current
limiters
No
Annex DD
Requirements for the mounting means of
rack-mounted equipment
No
Annex EE
Household and home/office document/media
shredders
No
Summary of compliance with National Differences
List of countries addressed:
EU Group Differences, EU Special National Conditions, EU A-Deviations
CA, DK, FI, DE, SE, GB, US.
CA=Canada, DK=Denmark, FI=Finland, DE=Germany, SE=Sweden, GB=United Kingdom, US=United
States of America.
For National Differences see end of this test report
The product fulfils the requirements of EN 60950-1:2006 + A11:2009 + A1:2010 + A12:2011.
TRF No. IEC60950_1C
Page 7 of 94
Report No. 18005046 001
Copy of marking plate
The artwork below may be only a draft. The use of certification marks on a product must be authorized
by the respective NCBs that own these marks.
(Additional requirements for markings. See 1.7 NOTE)
Caution labels
1.
Laser
Class 1 laser label (at DVD multi-drive)
TRF No. IEC60950_1C
Page 8 of 94
Report No. 18005046 001
2.
Battery
Warning statement provided in product’s user guide
This is also provided in the PCB motherboard’s user guide
3.
Fan symbol for the front system fans
TRF No. IEC60950_1C
Page 9 of 94
Report No. 18005046 001
Test item particulars...................................................:
Equipment mobility.....................................................: [] movable [] hand-held
[] transportable
[X] stationary [] for building-in [] direct plug-in
Connection to the mains ............................................: [X] pluggable equipment [X] type A [] type B
[] permanent connection
[] detachable power supply cord
[X] non-detachable power supply cord
[] not directly connected to the mains
Operating condition ....................................................: [X] continuous
[] rated operating / resting time:
Access location .........................................................: [X] operator accessible
[] restricted access location
Over voltage category (OVC) ...................................: [] OVC I
[] other:
[X] OVC II
[] OVC III
[] OVC IV
Mains supply tolerance (%) or absolute mains
supply values ............................................................: ±10%
Tested for IT power systems ....................................: [] Yes
[X] No
IT testing, phase-phase voltage (V) ..........................:
Class of equipment ...................................................: [X] Class I [] Class II
[] Not classified
[] Class III
Considered current rating of protective device as
part of the building installation (A) ............................: 16A (20A for Canada and United States)
Pollution degree (PD) ...............................................: [] PD 1
[X] PD 2
[] PD 3
IP protection class ....................................................: Not rated, indoor use only
Altitude during operation (m) ....................................: Up to 2000m
Altitude of test laboratory (m) ....................................: < 1000m
Mass of equipment (kg) ............................................: Approximately 11 kg
Possible test case verdicts:
- test case does not apply to the test object ................. : N/A
- test object does meet the requirement....................... : P (Pass)
- test object does not meet the requirement ................ : F (Fail)
Testing.......................................................................... :
Date of receipt of test item ............................................ : 2014.04.14
Date(s) of performance of tests .................................... : 2014.04.14 to 2014.06.05
TRF No. IEC60950_1C
Page 10 of 94
Report No. 18005046 001
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(see Enclosure #)" refers to additional information appended to the report.
"(see appended table)" refers to a table appended to the report.
Throughout this report a
comma /
point is used as the decimal separator.
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has
been provided ................................................................:
Yes
Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .......................... : Kontron Europe GmbH
Lise-Meitner-Str. 3-5
86156 Augsburg
Germany
TRF No. IEC60950_1C
Page 11 of 94
Report No. 18005046 001
General product information:
1) Application details / Description of the product:
The product tested is an industrial computer for use in a general office environment. It could be designed
to be installed in 19” racks or as a desktop unit by itself. It is intended to connect to PC peripheral
interface devices, such as monitor, USB keyboard, mouse, for its proper operation. The USB interface
peripherals could be plugged to front side of the USB2.0 type or the rear side of USB3.0 type connectors.
It is composed of a CB and TUV-mark approved switching AC-DC Power Supply unit, primary is isolated
by double or reinforced from secondary side. The power supply was tested as part of the overall
configuration of the equipment.
This unit is provided with burn-in software to simulate maximum load conditions.
a) Switching Power supply
CB report number: 11030607 001, issued on 2012 Oct 16, by TUV Rheinland Taiwan Ltd.,
Taichung Laboratory.
Manufacturer: FSP Group Inc.
TUV-mark report number: 10022615, license number: R 50129938
b) Motherboard PCB used is CB and UL approved.
CB report number: E194252-A30-CB-1, issued on 2014 Jan 10, by UL (Demko),
Manufacturer: Kontron Technology A/S.
UL test report: E194252-A30-UL issued on 2014 Jan 15, certificate number: 20140115-E194252
Detachable power supply cord is not evaluated in this test report.
Max. specified ambient temperature (C)…..: 50C
Supply Connection………………………… …: Appliance Inlet
Laser classification ……………………………: Class 1 laser product
Other conditions for built-in ............... ........ Installed according to Installation Instructions.
(see below)
PE connection:
Class I construction, required via appliance inlet.
2) Differences between the models: N/A
3) Options:
The equipment was tested without any optional accessory installed. Hence, this report does not cover
parameters that are influenced by the installation of optional accessory that might affect safety in the
meaning of this standard.
TRF No. IEC60950_1C
Page 12 of 94
Report No. 18005046 001
4) Insulation system:
- Secondary circuits are separated from primary by double/reinforced insulation.
- Primary circuits are separated from earth by at least basic insulation.
- All output / interface voltages are at SELV level.
- Secondary circuits are conductively connected to earth.
4.1) Sub-units (PCB’s, ... )
With pri – sec separation ......: SWPS
With pri – parts only ..............: (none)
HV-unit(s) ..............................: (none)
4.2) Pri - sec components, which are not part of the above mentioned sub-units:
(none)
4.3) Non certified pri-components directly mounted to chassis:
(certified components were only checked for correct-application (see 1.5.1)
(none)
Abbreviations used in the report:
- normal conditions
N.C.
- single fault conditions
S.F.C
- functional insulation
OP
- basic insulation
BI
- double insulation
DI
- supplementary insulation
SI
- between parts of opposite polarity
BOP
- reinforced insulation
RI
- protective earth/protective bonding
PE/PB
- primary
Pri
- (switching) power supply
(SW)PS
- secondary
sec
- high voltage
HV
- ground
gnd
- printed circuit (wiring) board
PCB
- input/output
- triple insulated wire
TIW
- installation instruction
- built-in application
B/I
TRF No. IEC60950_1C
I/O
ii
Page 13 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1
GENERAL
P
1.5
Components
P
1.5.1
General
P
Comply with IEC 60950-1 or relevant component
standard
(see appended tables 1.5.1)
P
1.5.2
Evaluation and testing of components
Components certified to
IEC/EN standards and/or
their harmonized standards,
are used within their ratings
and are checked for correct
application.
P
1.5.3
Thermal controls
P
1.5.4
Transformers
Approved thermistor
Transformers are part of
already certified power
supply.
1.5.5
Interconnecting cables
UL approved interconnecting
cable used.
P
1.5.6
Capacitors bridging insulation
N/A
1.5.7
Resistors bridging insulation
All capacitors between lines
and between primary to
secondary are part of
approved power supply and
certified according to IEC
60384-14:2005
See below.
1.5.7.1
Resistors bridging functional, basic or
supplementary insulation
1.5.7.2
Resistors bridging double or reinforced insulation
between a.c. mains and other circuits
N/A
1.5.7.3
Resistors bridging double or reinforced insulation
between a.c. mains and antenna or coaxial cable
N/A
1.5.8
Components in equipment for IT power systems
1.5.9
Surge suppressors
1.5.9.1
General
Evaluated in approved power
supply
See above.
See above.
1.5.9.2
Protection of VDRs
See above.
N/A
1.5.9.3
Bridging of functional insulation by a VDR
See above.
N/A
1.5.9.4
Bridging of basic insulation by a VDR
TRF No. IEC60950_1C
Bridging components are part
of already approved and
certified power supply.
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Page 14 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
1.5.9.5
Bridging of supplementary, double or reinforced
insulation by a VDR
1.6
Power interface
1.6.1
AC power distribution systems
TN power system
P
1.6.2
Input current
(see appended table 1.6.2)
P
1.6.3
Voltage limit of hand-held equipment
1.6.4
Neutral conductor
Not hand-held equipment.
Evaluated in approved power
supply
1.7
Marking and instructions
1.7.1
Power rating and identification markings
1.7.1.1
Power rating marking
Result - Remark
N/A
P
N/A
P
P
Rated voltage(s) or voltage range(s) (V) .............. : 100-240V
Symbol for nature of supply, for d.c. only .............. :
N/A
P
N/A
Rated frequency or rated frequency range (Hz) ... : 50 - 60 Hz
P
Rated current (mA or A) ........................................ : 4.5A max
P
Identification markings
P
See below.
Manufacturer’s name or trade-mark or
Kontron
identification mark ................................................. :
P
Model identification or type reference ................... : KISS 2U V2 KTQ87-A
P
Symbol for Class II equipment only ...................... :
1.7.2
N/A
P
Marking label is pasted on
metal enclosure.
Multiple mains supply connections..........................: Single supply
1.7.1.2
Verdict
N/A
Other markings and symbols ................................ : Additional symbols or
markings do not give rise to
misunderstanding.
Safety instructions and marking
See below.
Operating Instructions provided to the operator, containing necessary instructions
and caution information. English version checked.
P
P

At least the safety relevant information will be given in other applicable languages;
to be confirmed during the respective national approval.
1.7.2.1
General
See below.
P
1.7.2.2
Disconnect devices
Approved appliance inlet
used.
P
1.7.2.3
Overcurrent protective device
TRF No. IEC60950_1C
N/A
Page 15 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
1.7.2.4
IT power distribution systems
1.7.2.5
Operator access with a tool
For Norway compliance has
to be evaluated during the
national approval.
Operator is not instructed to
use any tool for access.
1.2.7.6
Ozone
1.7.3
Short duty cycles
Equipment is designed for
continuous operation.
N/A
1.7.4
Supply voltage adjustment ................................... :
Full range voltage design, no
necessary adjustment.
N/A
Methods and means of adjustment; reference to
installation instructions ......................................... :
See above.
N/A
1.7.5
Power outlets on the equipment .......................... :
No power outlets provided.
N/A
1.7.6
Fuse identification (marking, special fusing
characteristics, cross-reference) ......................... :
Evaluated in approved power
supply
N/A
1.7.7
Wiring terminals
See below.
N/A
1.7.7.1
Protective earthing and bonding terminals .......... :
N/A
1.7.7.2
Terminals for a.c. mains supply conductors
1.7.7.3
Terminals for d.c. mains supply conductors
Evaluated in approved power
supply
The equipment with
appliance
inlet, which is intended to use
the detachable type power
supply cord.
AC supplied equipment.
1.7.8
Controls and indicators
1.7.8.1
Identification, location and marking ..................... :
N/A
1.7.8.2
Colours ................................................................ :
N/A
1.7.8.3
Symbols according to IEC 60417 ........................ :
N/A
N/A
N/A
No safety relevant control nor
indicator.
Marking Symbol (IEC 604175007) for "ON” of the power
supply switch, symbol (IEC
60417-5008) for “OFF” of the
approved power supply.
N/A
N/A
N/A
P
Marking Symbol (IEC 604175009) for on/off of the power
switch for the motherboard,
used for functional purpose.
1.7.8.4
Markings using figures ....................................... :
Not used.
N/A
1.7.9
Isolation of multiple power sources .................... :
Only one supply from the
mains.
N/A
TRF No. IEC60950_1C
Page 16 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1.7.10
Thermostats and other regulating devices ......... :
Thermistor used in the CB
approved motherboard.
1.7.11
Durability
The label was subjected to
the permanence of marking
test. The label was rubbed
with cloth soaked with water
for 15 s and then again for 15
s with the cloth soaked with
petroleum spirit.
Verdict
N/A
P
After this test there was no
damage to the label. The
marking on the label did not
fade. There was no curling
nor lifting of the label edge.
1.7.12
Removable parts
No required marking placed
on removable part (top cover
of the enclosure)
N/A
1.7.13
Replaceable batteries ......................................... :
Lithium Battery CR2032 not
replaceable by user. Warning
statement provided in
servicing instructions of user
manual.
P
Language(s) ........................................................ :
English

Equipment for restricted access locations ........... :
Not intended for restricted
access location.
1.7.14
TRF No. IEC60950_1C
N/A
Page 17 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2
PROTECTION FROM HAZARDS
P
2.1
Protection from electric shock and energy hazards
P
2.1.1
Protection in operator access areas
See below.
P
2.1.1.1
Access to energized parts
Only SELV circuits are
accessible
P
Test by inspection ................................................. : Operator cannot contact any
hazardous bare parts or parts
with only basic insulation to
hazardous voltage.
Verdict
P
Protection established by
approved power supply.
Test with test finger (Figure 2A) ........................... : No access to hazardous
parts.
P
Test with test pin (Figure 2B) ................................ : The test pin cannot touch
hazardous bare parts through
any openings in the external
enclosure.
P
Test with test probe (Figure 2C) ........................... : No TNV circuits.
N/A
2.1.1.2
Battery compartments
No battery compartment.
No TNV circuits.
N/A
2.1.1.3
Access to ELV wiring
No ELV circuits.
N/A
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
Not applicable.

2.1.1.4
Access to hazardous voltage circuit wiring
Not accessible. Refer to
clause 2.1.1 above.
2.1.1.5
Energy hazards ..................................................... : Evaluated in approved power
supply
Manual controls
No manual controls.
Evaluated in approved power
Discharge of capacitors in equipment
supply
Measured voltage (V); time-constant (s) ............... :
2.1.1.6
2.1.1.7
2.1.1.8
Energy hazards – d.c. mains supply
No dc mains supply
N/A
N/A
N/A
N/A

N/A
a) Capacitor connected to the d.c. mains supply . :
N/A
b) Internal battery connected to the d.c. mains
supply .................................................................... :
N/A
2.1.1.9
Audio amplifiers .................................................... : Not provided.
N/A
2.1.2
Protection in service access areas
N/A
TRF No. IEC60950_1C
No hazardous voltage used.
Page 18 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.1.3
Protection in restricted access locations
Not intended to be installed in
a restricted access location.
2.2
SELV circuits
Verdict
N/A
N/A
CB approved power supply and UL CB approved motherboard PCB used.
2.2.1
General requirements
N/A
2.2.2
Voltages under normal conditions (V) .................. :
N/A
2.2.3
Voltages under fault conditions (V) ....................... :
N/A
2.2.4
Connection of SELV circuits to other circuits ..... :
N/A
2.3
TNV circuits
N/A
No TNV circuits.
2.3.1
Limits
N/A
Type of TNV circuits .............................................. :

2.3.2
Separation from other circuits and from accessible
parts
N/A
2.3.2.1
General requirements
N/A
2.3.2.2
Protection by basic insulation
N/A
2.3.2.3
Protection by earthing
N/A
2.3.2.4
Protection by other constructions ......................... :
N/A
2.3.3
Separation from hazardous voltages
N/A
Insulation employed ............................................... :
2.3.4
Connection of TNV circuits to other circuits
Insulation employed ............................................... :

N/A

2.3.5
Test for operating voltages generated externally
N/A
2.4
Limited current circuits
N/A
Evaluation done in approved power supply. Output circuit of power supply as
limited current circuit connected to motherboard PCB.
2.4.1
General requirements
N/A
2.4.2
Limit values
N/A
Frequency (Hz) ...................................................... :

Measured current (mA) .......................................... :

Measured voltage (V) ............................................ :

TRF No. IEC60950_1C
Page 19 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark

Measured circuit capacitance (nF or µF) ............... :
2.4.3
Connection of limited current circuits to other
circuits
2.5
Limited power sources
Verdict
N/A
P
a) Inherently limited output
N/A
b) Impedance limited output
Approved PTC used.
(see appended table 2.5)
P
c) Regulating network limited output under normal
operating and single fault condition
N/A
d) Overcurrent protective device limited output
N/A
Max. output voltage (V), max. output current (A),
Considered are following
max. apparent power (VA) ..................................... : ports: USB 2.0 type (at the
front enclosure), USB 3.0
type and DisplayPort (at rear
enclosure)

(see appended table 2.5)
Current rating of overcurrent protective device (A) .: Not applicable
Use of integrated circuit (IC) current limiters
Not applicable.
P
2.6
Provisions for earthing and bonding
2.6.1
Protective earthing
PE connection through
earthing pin of appliance inlet
of approved power supply.
Ground connection to
motherboard is by output
wires of the power supply.
2.6.2
Functional earthing
No functional earthing
provided.
2.6.3
Protective earthing and protective bonding
conductors
See clause 2.6.1 above.
2.6.3.1
General
See below.
2.6.3.2
Size of protective earthing conductors
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
Size of protective bonding conductors
N/A
P
N/A

N/A
2
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
TRF No. IEC60950_1C
P
N/A
2
2.6.3.3


Page 20 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Protective current rating (A), cross-sectional area
(mm2), AWG ........................................................... :
2.6.3.4
See appended table 2.6.3.4
Resistance of earthing conductors and their
terminations; resistance (), voltage drop (V), test
current (A), duration (min)...................................... :
2.6.3.5
Colour of insulation ................................................ : See clause 2.6.3.2
2.6.4
Terminals
See below
P
2.6.4.1
General
See below.
P
2.6.4.2
Protective earthing and bonding terminals
The earthing terminal in the
appliance inlet is regarded as
the main protective earthing
terminal. The protective
bonding conductors are
evaluated by 2.6.3.4 test for
approved power supply
P
2.6.4.3
2.6.5
2.6.5.1
2.6.5.2
2.6.5.3
2.6.5.4
2.6.5.5
P
N/A
Rated current (A), type, nominal thread diameter
(mm) ....................................................................... :

Appliance inlet was
considered as protective
earthing conductor.
Protective bonding
conductors separation from
protective earthing conductor
of approved power supply.
Integrity of protective earthing
See below.
The equipment has its own
Interconnection of equipment
earthing connection; any
other units interconnected to
it via the output connector
shall provide SELV only.
Components in protective earthing conductors and No switch or overcurrent
protective device in protective
protective bonding conductors
earthing or protective
bonding conductor.
It
is not possible to
Disconnection of protective earth
disconnect
earth without disconnecting
mains as an appliance inlet is
used.
The earth connection made
Parts that can be removed by an operator
earlier and broken later than
the supply connections.
Parts removed during servicing
It is not necessary to
disconnect earthing except
for the removing of the
earthed parts itself.
P
Separation of the protective earthing conductor
from protective bonding conductors
TRF No. IEC60950_1C
P
P
P
N/A
P
P
Page 21 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.6.5.6
Corrosion resistance
2.6.5.7
Screws for protective bonding
All safety earthing
connections in compliance
with Annex J.
Only ISO thread screw used
in metal chassis for protective
bonding. Metal thickness at
least twice the pitch of the
screw.
Verdict
P
N/A
No self-tapping or spaced
thread screws.
2.6.5.8
Reliance on telecommunication network or cable
distribution system
2.7
Overcurrent and earth fault protection in primary circuits
Evaluated in approved power
Basic requirements
supply.
Instructions when protection relies on building
See above.
installation
2.7.1
No TNV.
N/A
P
P
N/A
2.7.2
Faults not simulated in 5.3.7
N/A
2.7.3
Short-circuit backup protection
N/A
2.7.4
Number and location of protective devices ........... :
N/A
2.7.5
Protection by several devices
N/A
2.7.6
Warning to service personnel ................................ :
N/A
2.8
Safety interlocks
N/A
No operator accessible areas which presents hazards in the meaning of this
standard
2.8.1
General principles
N/A
2.8.2
Protection requirements
N/A
2.8.3
Inadvertent reactivation
N/A
2.8.4
Fail-safe operation
N/A
Protection against extreme hazard
N/A
2.8.5
Moving parts
N/A
2.8.6
Overriding
N/A
2.8.7
Switches, relays and their related circuits
N/A
2.8.7.1
Separation distances for contact gaps and their
related circuits (mm) ............................................. :
N/A
2.8.7.2
Overload test
N/A
TRF No. IEC60950_1C
Page 22 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.8.7.3
Endurance test
N/A
2.8.7.4
Electric strength test
N/A
2.8.8
Mechanical actuators
N/A
2.9
Electrical insulation
P
2.9.1
Properties of insulating materials
Natural rubber, asbestos or
hygroscopic materials are not
used.
P
2.9.2
Humidity conditioning
Tested for 48 hrs
P
Relative humidity (%), temperature (°C) ............... : 93%. 25°C
2.9.3
Grade of insulation
2.9.4
Separation from hazardous voltages
The adequate levels of safety
insulation is provided and
maintained to comply with the
requirements of this
standard.
See below
Verdict

P
P
Method(s) used ..................................................... : Method 1

P
N/A
2.10.1.1
Clearances, creepage distances and distances through insulation
Evaluated in approved power
General
supply.
Frequency ............................................................. :
2.10.1.2
Pollution degrees .................................................. :
N/A
2.10.1.3
Reduced values for functional insulation
N/A
2.10.1.4
Intervening unconnected conductive parts
2.10.1.5
Insulation with varying dimensions
2.10.1.6
Special separation requirements
No TNV circuit.
N/A
2.10.1.7
Insulation in circuits generating starting pulses
N/A
2.10.2
Determination of working voltage
No lamps.
Evaluated in approved power
supply
2.10.2.1
General
N/A
2.10.2.2
RMS working voltage
N/A
2.10.2.3
Peak working voltage
N/A
2.10.3
Clearances
2.10.3.1
General
2.10
2.10.1
TRF No. IEC60950_1C
No such conductive parts.
N/A
N/A
N/A
No further creepage and
clearance measurements
necessary, refer to clause
2.10.1
See above.
N/A
P
P
Page 23 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10.3.2
Normal transient voltage
considered.
a) AC mains supply ............................................... : Overvoltage category II for
primary circuit and transient
voltage 2500Vpeak.
b) Earthed d.c. mains supplies ............................. :
N/A
c) Unearthed d.c. mains supplies ......................... :
N/A
d) Battery operation .............................................. :
N/A
Mains transient voltages
refer to clause 2.10.1
Verdict
P
P
2.10.3.3
Clearances in primary circuits
N/A
2.10.3.4
Clearances in secondary circuits
2.10.3.5
Clearances in circuits having starting pulses
2.10.3.6
Transients from a.c. mains supply ........................ : See sub-clause 2.10.3.2.
2.10.3.7
Transients from d.c. mains supply ........................ :
N/A
2.10.3.8
Transients from telecommunication networks and
cable distribution systems ..................................... :
N/A
2.10.3.9
Measurement of transient voltage levels
N/A
No lamps
See sub-clause 2.10.3.2.
N/A
P
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply ....................................... :
N/A
For a d.c. mains supply ......................................... :
N/A
b) Transients from a telecommunication network :
N/A
2.10.4
Creepage distances
2.10.4.1
General
2.10.4.2
Material group and comparative tracking index
refer to clause 2.10.1
P
P
Material group IIIb is
assumed to be used
P

CTI tests................................................................. :
2.10.4.3
Minimum creepage distances
2.10.5
Solid insulation
P
2.10.5.1
General
P
2.10.5.2
Distances through insulation
(see appended table 2.10.5)
2.10.5.3
Insulating compound as solid insulation
Certified sources of photo
couplers used in approved
power supply.
N/A
2.10.5.4
Semiconductor devices
See above.
N/A
2.10.5.5.
Cemented joints
2.10.5.6
Thin sheet material – General
2.10.5.7
Separable thin sheet material
TRF No. IEC60950_1C
refer to clause 2.10.1
N/A
P
N/A
Evaluated in approved power
supply.
See above.
N/A
N/A
Page 24 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict

Number of layers (pcs) .......................................... :
2.10.5.8
Non-separable thin sheet material
N/A
2.10.5.9
Thin sheet material – standard test procedure
N/A

Electric strength test
2.10.5.10
Thin sheet material – alternative test procedure
Electric strength test
Evaluated in approved power
supply.
See above.
N/A

2.10.5.11
Insulation in wound components
N/A
2.10.5.12
Wire in wound components
N/A
Working voltage .................................................... :
N/A
a) Basic insulation not under stress ...................... :
N/A
b) Basic, supplementary, reinforced insulation ..... :
N/A
c) Compliance with Annex U ................................. :
N/A
Two wires in contact inside wound component;
angle between 45 and 90 .................................. :
N/A
Wire with solvent-based enamel in wound
components
N/A
2.10.5.13
Electric strength test
(see appended table 2.10.5)

Routine test
N/A
Additional insulation in wound components
N/A
Working voltage .................................................... :
N/A
- Basic insulation not under stress ........................ :
N/A
- Supplementary, reinforced insulation ................. :
N/A
2.10.6
Construction of printed boards
N/A
2.10.6.1
Uncoated printed boards
N/A
2.10.6.2
Coated printed boards
N/A
2.10.6.3
Insulation between conductors on the same inner
surface of a printed board
N/A
2.10.6.4
Insulation between conductors on different layers
of a printed board
N/A
Distance through insulation
N/A
Number of insulation layers (pcs) .......................... :
N/A
2.10.5.14
2.10.7
Component external terminations
2.10.8
Tests on coated printed boards and coated
components
TRF No. IEC60950_1C
Evaluated by approved
power supply
N/A
N/A
Page 25 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
2.10.8.1
Sample preparation and preliminary inspection
N/A
2.10.8.2
Thermal conditioning
N/A
2.10.8.3
Electric strength test
N/A
2.10.8.4
Abrasion resistance test
N/A
2.10.9
Thermal cycling
2.10.10
Test for Pollution Degree 1 environment and
insulating compound
N/A
2.10.11
Tests for semiconductor devices and cemented
joints
N/A
2.10.12
Enclosed and sealed parts
N/A
Certified sources of photo
couplers used in approved
power supply.
Verdict
N/A
3
WIRING, CONNECTIONS AND SUPPLY
P
3.1
General
P
3.1.1
Current rating and overcurrent protection
3.1.2
Protection against mechanical damage
3.1.3
Securing of internal wiring
TRF No. IEC60950_1C
Internal wirings are UL
recognized wiring which is
PVC insulated, rated VW-1,
300V, min.80°C and
considered for approved
power supply lead wires of
L/N min. 105°C.
The wiring gauge is suitable
for current intended to be
carried.
Wires do not touch sharp
edges. Where they touch
heatsinks additional tubing or
cable tie is provided so that
the heatsink cannot damage
the insulation and cause
hazard.
The wiring is so routed and
fixed that there is not
excessive strength on the
wire and terminal
connections. Damage of the
conductor insulation or
loosening of the terminal
connection is unlikely.
P
P
P
Page 26 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
3.1.4
Insulation of conductors
3.1.5
Beads and ceramic insulators
3.1.6
Screws for electrical contact pressure
3.1.7
Insulating materials in electrical connections
3.1.8
Self-tapping and spaced thread screws
3.1.9
Termination of conductors
Result - Remark
The insulation of the
individual conductors is
suitable for the application
and the working voltage
considered for approved
power supply. For the
insulation material see subclause 3.1.1.
Not used.
No screws of insulating
material.
Not used.
No self tapping screws are
used.
All conductors are reliable
secured.
10N pull test performed for all
relevant conductors.
No hazards observed.
The power switch, LED
indicators and wirings are
sleeved by the sufficient
length of heat shrinkage tube.
10 N pull test
Verdict
P
N/A
N/A
N/A
N/A
P
P
3.1.10
Sleeving on wiring
P
3.2
Connection to a mains supply
3.2.1
Means of connection
See below.
P
3.2.1.1
Connection to an a.c. mains supply
Appliance inlet provided.
P
3.2.1.2
Connection to a d.c. mains supply
Only a.c. mains supply.
N/A
3.2.2
Multiple supply connections
N/A
3.2.3
Permanently connected equipment
Single supply
Unit is not a permanently
connected equipment.
P
N/A

Number of conductors, diameter of cable and
conduits (mm) ....................................................... :
Evaluated by approved power
supply
3.2.4
Appliance inlets
3.2.5
Power supply cords
N/A
3.2.5.1
AC power supply cords
N/A

Type ...................................................................... :
2

Rated current (A), cross-sectional area (mm ),
AWG ..................................................................... :
3.2.5.2
DC power supply cords
3.2.6
Cord anchorages and strain relief
TRF No. IEC60950_1C
N/A
AC mains supply.
N/A
N/A
Page 27 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Mass of equipment (kg), pull (N) ......................... :

Longitudinal displacement (mm) ........................... :

3.2.7
Protection against mechanical damage
3.2.8
Cord guards
There are no parts of this
equipment that may damage
the power supply cord to be
provided.
N/A
N/A
Diameter or minor dimension D (mm); test mass (g)
............................................................................... :

Radius of curvature of cord (mm) .......................... :

3.2.9
Supply wiring space
N/A
3.3
Wiring terminals for connection of external conductors
N/A
3.3.1
Wiring terminals
N/A
3.3.2
Connection of non-detachable power supply cords
N/A
3.3.3
Screw terminals
N/A
3.3.4
Conductor sizes to be connected
N/A
No wiring terminals for
connection of external
conductors.

Rated current (A), cord/cable type, cross-sectional
area (mm2) ............................................................. :
3.3.5
Wiring terminal sizes
N/A

Rated current (A), type, nominal thread diameter
(mm) ...................................................................... :
3.3.6
Wiring terminal design
N/A
3.3.7
Grouping of wiring terminals
N/A
3.3.8
Stranded wire
N/A
3.4
Disconnection from the mains supply
3.4.1
General requirement
See below.
P
3.4.2
Disconnect devices
P
3.4.3
Permanently connected equipment
3.4.4
Parts which remain energized
Approved appliance inlet
used are considered
disconnect devices.
Not permanently connected
equipment.
None
3.4.5
Switches in flexible cords
No switches in flexible cords.
TRF No. IEC60950_1C
P
N/A
N/A
N/A
Page 28 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
3.4.6
3.4.11
Number of poles - single-phase and d.c. equipment The disconnect device
disconnects both poles
simultaneously.
Number of poles - three-phase equipment
The switch not as disconnect
Switches as disconnect devices
devices.
Plugs as disconnect devices
The equipment is
Interconnected equipment
interconnected to other
devices by secondary output
only.
Single supply.
Multiple power sources
3.5
Interconnection of equipment
3.5.1
General requirements
3.5.2
Types of interconnection circuits .......................... :
3.5.3
ELV circuits as interconnection circuits
3.5.4
Data ports for additional equipment
3.4.7
3.4.8
3.4.9
3.4.10
Result - Remark
Verdict
P
N/A
N/A
N/A
N/A
N/A
P
The unit is not considered for
connection to TNV.
Interconnection circuits of
SELV via secondary output
connectors.
No ELV interconnection.
Front USB2.0, rear USB3.0,
Display port, RS232 data
ports supplied from LPS.
P
P
N/A
P
Tested accordance to clause
2.5.
4
PHYSICAL REQUIREMENTS
P
4.1
Stability
P
Unit does not fall over.
P
Test force (N) ........................................................ : Not floor standing unit
P
4.2
Mechanical strength
P
4.2.1
General
Angle of 10
TRF No. IEC60950_1C
Outer metal enclosure shows
sufficient strength to
withstand expected handling
conditions.
P
Page 29 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Rack-mounted equipment.
Fall test
Equipment fixed in place and
provided with equipment
subassemblies or racks
having a top installation
position less than 1 m in
height from the supporting
surface.
10N force applied to
components. No hazard
observed.
30N applied to front panel of
the enclosure. No crack and
distortion are observed.
250 N force applied to the
external sides of the unit:
front, left, right, top and
bottom. No crack and
distortion are observed.
Impact force applied. No
damage, no crack observed.
Top, bottom
Swing test
Front, left, right
4.2.2
Steady force test, 10 N
4.2.3
Steady force test, 30 N
4.2.4
Steady force test, 250 N
4.2.5
Impact test
Verdict
N/A
P
P
P
P
P
P
4.2.6
Drop test; height (mm) .......................................... :
N/A
4.2.7
Stress relief test
Metal enclosure used.
N/A
4.2.8
Cathode ray tubes
No CRT in the unit.
N/A
Picture tube separately certified ............................ :
N/A
4.2.9
High pressure lamps
N/A
4.2.10
Wall or ceiling mounted equipment; force (N) ....... :
N/A
4.3
Design and construction
4.3.1
Edges and corners
4.3.2
Handles and manual controls; force (N) ............. :
4.3.3
Adjustable controls
TRF No. IEC60950_1C
P
Edges and corners of the
enclosure are rounded and
smooth.
No safety related handles or
controls to indicate the
position of switch.
No adjustable controls.
P
N/A
N/A
Page 30 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.3.4
Securing of parts
4.3.5
Connection by plugs and sockets
4.3.6
Direct plug-in equipment
Electrical and mechanical
connections can be expected
to withstand usual mechanical
stress. No loosening or
clearance and creepage
impairing distances likely to
occur.
Mismatching of connectors
either not possible or does
not result in any hazard.
Not direct plug-in type.
Verdict
P
N/A
N/A
Torque .................................................................. :

Compliance with the relevant mains plug standard
.............................................................................. :
N/A
4.3.7
Heating elements in earthed equipment
No heating elements.
4.3.8
Batteries
Non-rechargable approved
litium battery used
- Overcharging of a rechargeable battery
- Unintentional charging of a non-rechargeable
battery
4.3.9
Oil and grease
4.3.10
Dust, powders, liquids and gases
4.3.11
Containers for liquids or gases
4.3.12
Flammable liquids ................................................ :
P
N/A
No hazard observed.
(see appended tables 4.3.8)
- Reverse charging of a rechargeable battery
- Excessive discharging rate for any battery
N/A
P
N/A
No hazard observed.
(see appended tables 4.3.8)
Insulation in intended use not
considered to be exposed to
oil or grease.
Equipment in intended use
not considered to be exposed
to these.
No container for liquid or gas
provided.
No flammable liquids
provided.
P
N/A
N/A
N/A
N/A
Quantity of liquid (l) .............................................. :
N/A
Flash point (C) .................................................... :
N/A
4.3.13
Radiation
P
4.3.13.1
General
N/A
4.3.13.2
Ionizing radiation
N/A
Measured radiation (pA/kg) ................................. :

Measured high-voltage (kV) ................................. :

Measured focus voltage (kV) ............................... :

TRF No. IEC60950_1C
Page 31 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark

CRT markings ...................................................... :
4.3.13.3
Verdict
Effect of ultraviolet (UV) radiation on materials
N/A
Part, property, retention after test, flammability
classification ......................................................... :
N/A
4.3.13.4
Human exposure to ultraviolet (UV) radiation ...... :
N/A
4.3.13.5
Lasers (including laser diodes) and LEDs
4.3.13.5.1
Lasers (including laser diodes)
See below.
For laser, see IEC 60950-1
test report E75017-A53-CB-1
from UL Japan, Inc. In this
report, it shows a laser
measurement test report
reference number
12CA14583, tested for IEC
60825-1: 2007 clause 8 and 9
on DVD multi drive, by UL
Japan, Inc.
P
P
LED used for indicating only.
Laser class ........................................................... :
Class 1 laser product.
4.3.13.5.2
Light emitting diodes (LEDs)
LED is low power and for
status indication.
4.3.13.6
Other types .......................................................... :
4.4
Protection against hazardous moving parts
4.4.1
General

N/A
P
Access to hazardous moving
parts prevented by
construction.
P
The secondary DC Fans at
the front enclosure are
protected by the fan guard.
4.4.2
Protection in operator access areas .................... :
Household and home/office document/media
shredders
4.4.3
Protection in restricted access locations ............. :
TRF No. IEC60950_1C
DC fans and CPU fan are fully
enclosed inside enclosure
and not accessible to
operator.
See above.
Not shredder
P
N/A
N/A
Page 32 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.4.4
Protection in service access areas
Hazardous moving parts in
service area are adequately
covered to prevent
unintentional contact during
servicing.
Verdict
P
Refer to Cl. 4.4.1
4.4.5
Protection against moving fan blades
No user accessible fan blade.
P
4.4.5.1
General
1) DC ventilation system Fan
(PSD1207PTB1-A)
P
m=0.096kg, r=35mm,
N=5100rpm, K=1835.27
2) CPU fan
(R128015BU)
m=0.053kg, r=40mm,
N=4200rpm, K=897.52
Not considered to cause pain or injury.
a)………….:
P
1) 1.10, 2) 0.65
Is considered to cause pain, not injury.
b) …………:
P
1) 0.74
Considered to cause injury.
c) …………:
4.4.5.2
Protection for users
No operator serviceable parts
inside.
Fans are enclosed inside of
equipment adequately by
enclosure, which can remove
by using the tool.
N/A
P
No user accessible fan blade
under normal operation.
Use of symbol or
warning ……………………………:
4.4.5.3
N/A
Protection for service persons
Fan blade classified as
4.4.5.1 b)
Use of symbol or
warning ……………………………:
A triangular shaped warning
sign similar to ISO 3864-2 will
be used.
TRF No. IEC60950_1C
P
N/A
Page 33 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
4.5
Thermal requirements
4.5.1
General
No exceeding temperature.
P
4.5.2
Temperature tests
See appended table 4.5.
P
Normal load condition per Annex L ...................... :
(See Annex L.7)

4.5.3
Temperature limits for materials
(see appended table 4.5)
P
4.5.4
Touch temperature limits
P
4.5.5
Resistance to abnormal heat ............................... :
(see appended table 4.5)
See appended table 4.5.5 for
CPU fan frame enclosure.
P
P
Other material evaluated in
approved built-in power
supply.
4.6
Openings in enclosures
4.6.1
Top and side openings
Dimensions (mm) ................................................. :
4.6.2
Bottoms of fire enclosures
Construction of the bottomm, dimensions (mm) .. :
P
All openings comply with the
5° angle projection. No
hazardous parts within 5°
projection area from the
openings.
No hazardous voltage in unit
except closed frame built-in
power supply. SELV for PCB
motherboard.
3.8mm, 6.89 mm circular
holes.
Protection against emission of
flame, molten metal, flaming
or glowing particles or drops
by constructions.
No openings below parts
requiring fire enclosure.
P

P

4.6.3
Doors or covers in fire enclosures
Not used.
N/A
4.6.4
Openings in transportable equipment
Not transportable equipment.
N/A
4.6.4.1
Constructional design measures
Dimensions (mm) ................................................. :
N/A

4.6.4.2
Evaluation measures for larger openings
N/A
4.6.4.3
Use of metallized parts
N/A
4.6.5
Adhesives for constructional purposes
N/A
Conditioning temperature (C), time (weeks) ....... :
TRF No. IEC60950_1C

Page 34 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
4.7
Resistance to fire
4.7.1
Reducing the risk of ignition and spread of flame
Result - Remark
Verdict
P
Metal enclosure used.
Method 1, selection and application of components (see appended table 1.5.1)
wiring and materials
Method 2, application of all of simulated fault
condition tests
Not considered.
4.7.2
Conditions for a fire enclosure
See below.
4.7.2.1
Parts requiring a fire enclosure
4.7.2.2
Parts not requiring a fire enclosure
P
P
N/A
P
N/A
PCB motherboard’s output
was evaluated and comply
with limited power source
requirement. PCB is of min V1 material. See clause 2.5.
P
So no fire enclosure required.
4.7.3
Materials
P
See appended table 1.5.1 for
details.
Metal enclosure used.
N/A
N/A
4.7.3.1
General
4.7.3.2
Materials for fire enclosures
4.7.3.3
Materials for components and other parts outside
fire enclosures
Refer to clause 4.7.3.5
4.7.3.4
Materials for components and other parts inside
fire enclosures
Internal components except
small parts are V-2, HF-2 or
better.
4.7.3.5
Materials for air filter assemblies
Evaluated in 4.6.2
4.7.3.6
Materials used in high-voltage components
TRF No. IEC60950_1C
P
P
N/A
N/A
Page 35 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
5
ELECTRICAL REQUIREMENTS AND SIMULATED ABNORMAL CONDITIONS
P
5.1
Touch current and protective conductor current
P
5.1.1
General
(see appended Table 5.1)
P
5.1.2
Configuration of equipment under test (EUT)
P
5.1.2.1
Single connection to an a.c. mains supply
See below.
EUT has only single AC
mains connection.
5.1.2.2
Redundant multiple connections to an a.c. mains
supply
N/A
5.1.2.3
Simultaneous multiple connections to an a.c. mains
supply
N/A
5.1.3
Test circuit
5.1.4
Application of measuring instrument
5.1.5
Test procedure
5.1.6
P
P
Test measurements
Equipment of figure 5A used.
Using measuring instrument
in annex D.
The touch current was
measured from primary to
earth and to output connector
See below.
Supply voltage (V) ................................................ :
(see appended Table 5.1)

Measured touch current (mA) .............................. :
(see appended Table 5.1)

Max. allowed touch current (mA) ......................... :
(see appended Table 5.1)

Measured protective conductor current (mA) ...... :
(see appended Table 5.1)

Max. allowed protective conductor current (mA) .. :
(see appended Table 5.1)

5.1.7
Equipment with touch current exceeding 3,5 mA
Not exceeded.
5.1.7.1
General ................................................................. :
5.1.7.2
Simultaneous multiple connections to the supply
5.1.8
Touch currents to telecommunication networks and No TNV circuit connection.
cable distribution systems and from
telecommunication networks
N/A
5.1.8.1
Limitation of the touch current to a
telecommunication network or to a cable
distribution system
N/A
5.1.8.2
P
P
P
N/A
N/A
Single supply equipment.
N/A
Supply voltage (V) ................................................ :

Measured touch current (mA) .............................. :

Max. allowed touch current (mA) ......................... :

Summation of touch currents from
telecommunication networks
N/A
a) EUT with earthed telecommunication ports ..... :
N/A
TRF No. IEC60950_1C
Page 36 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
b) EUT whose telecommunication ports have no
reference to protective earth
Verdict
N/A
P
5.2
Electric strength
5.2.1
General
5.2.2
Test procedure
P
5.3
Abnormal operating and fault conditions
P
5.3.1
Protection against overload and abnormal
operation
(see appended table 5.3)
P
5.3.2
Motors
DC fan and CPU fan locked.
Temperature limits of Annex
B not exceeded.
P
(see appended table 5.2)
P
(see appended table 5.3)
5.3.3
Transformers
Trasnformers are part of
approved power supply.
N/A
5.3.4
Functional insulation ............................................. :
N/A
5.3.5
Electromechanical components
Evaluated in approved power
supply.
No electromechanical
component provided.
5.3.6
Audio amplifiers in ITE ......................................... :
5.3.7
Simulation of faults
See appended table 5.3.
5.3.8
Unattended equipment
Approved thermistor used on
approved motherboard.
5.3.9
Compliance criteria for abnormal operating and
fault conditions
See below.
P
5.3.9.1
During the tests
P
5.3.9.2
After the tests
Neither fire burns the
equipment nor molten metal.
Electric strength test primary
to secondary and primary to
PB were passed.
TRF No. IEC60950_1C
N/A
N/A
P
N/A
P
Page 37 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
6
CONNECTION TO TELECOMMUNICATION NETWORKS
N/A
6.1
Protection of telecommunication network service persons, and users of other
equipment connected to the network, from hazards in the equipment
N/A
6.1.1
Protection from hazardous voltages
N/A
6.1.2
Separation of the telecommunication network from earth
N/A
6.1.2.1
Requirements
N/A
Supply voltage (V) ................................................ :

Current in the test circuit (mA) ........................... :

6.1.2.2
Exclusions ............................................................ :
N/A
6.2
Protection of equipment users from overvoltages on telecommunication
networks
N/A
6.2.1
Separation requirements
N/A
6.2.2
Electric strength test procedure
N/A
6.2.2.1
Impulse test
N/A
6.2.2.2
Steady-state test
N/A
6.2.2.3
Compliance criteria
N/A
6.3
Protection of the telecommunication wiring system from overheating
N/A
Max. output current (A) ........................................ :

Current limiting method ........................................ :

7
CONNECTION TO CABLE DISTRIBUTION SYSTEMS
N/A
7.1
General
N/A
7.2
Protection of cable distribution system service
persons, and users of other equipment connected
to the system, from hazardous voltages in the
equipment
N/A
7.3
Protection of equipment users from overvoltages
on the cable distribution system
N/A
7.4
Insulation between primary circuits and cable
distribution systems
N/A
7.4.1
General
N/A
7.4.2
Voltage surge test
N/A
7.4.3
Impulse test
N/A
TRF No. IEC60950_1C
Page 38 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
A
ANNEX A, TESTS FOR RESISTANCE TO HEAT AND FIRE
N/A
A.1
Flammability test for fire enclosures of movable
equipment having a total mass exceeding 18 kg,
and of stationary equipment (see 4.7.3.2)
N/A
A.1.1
Samples ................................................................ :

Wall thickness (mm) ............................................. :

A.1.2
Conditioning of samples; temperature (C) ......... :
N/A
A.1.3
Mounting of samples ............................................ :
N/A
A.1.4
Test flame (see IEC 60695-11-3)
N/A
Flame A, B, C or D ............................................... :
Verdict

A.1.5
Test procedure
N/A
A.1.6
Compliance criteria
N/A
Sample 1 burning time (s)..................................... :

Sample 2 burning time (s)..................................... :

Sample 3 burning time (s)..................................... :

A.2
Flammability test for fire enclosures of movable equipment having a total mass not
exceeding 18 kg, and for material and components located inside fire enclosures
(see 4.7.3.2 and 4.7.3.4)
A.2.1
Samples, material ................................................. :

Wall thickness (mm) ............................................. :

A.2.2
Conditioning of samples; temperature (°C) ......... :
N/A
A.2.3
Mounting of samples ............................................ :
N/A
A.2.4
Test flame (see IEC 60695-11-4)
N/A
Flame A, B or C ................................................... :
N/A

A.2.5
Test procedure
N/A
A.2.6
Compliance criteria
N/A
A.2.7
Sample 1 burning time (s)..................................... :

Sample 2 burning time (s)..................................... :

Sample 3 burning time (s)..................................... :

Alternative test acc. to IEC 60695-11-5, cl. 5 and 9
N/A
Sample 1 burning time (s)..................................... :

Sample 2 burning time (s)..................................... :

Sample 3 burning time (s)..................................... :

TRF No. IEC60950_1C
Page 39 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
A.3
Hot flaming oil test (see 4.6.2)
N/A
A.3.1
Mounting of samples
N/A
A.3.2
Test procedure
N/A
A.3.3
Compliance criterion
N/A
B
ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and
5.3.2)
P
B.1
General requirements
EN approved secondary DC
fans used. UL approved fan
used for CPU.
P
Position ................................................................ :
(see appended table 1.5.1)

Manufacturer ........................................................ :
(see appended table 1.5.1)

Type ..................................................................... :
(see appended table 1.5.1)

Rated values ....................................................... :
(see appended table 1.5.1)

B.2
Test conditions
N/A
B.3
Maximum temperatures
(see appended table 5.3)
P
B.4
Running overload test
DC fans in secondary only
N/A
B.5
Locked-rotor overload test
DC fans in secondary only
N/A
Test duration (days) ............................................. :

Electric strength test: test voltage (V) .................. :

B.6
Running overload test for d.c. motors in secondary
circuits
N/A
B.6.1
General
N/A
B.6.2
Test procedure
N/A
B.6.3
Alternative test procedure
N/A
B.6.4
Electric strength test; test voltage (V) .................. :
N/A
B.7
Locked-rotor overload test for d.c. motors in
secondary circuits
P
B.7.1
General
P
B.7.2
Test procedure
Rotor of CPU fan and system
ventilation fans are locked for
7 hours. See appended table
5.3.
P
Temperatures do not exceed
the values in table B.1
B.7.3
Alternative test procedure
TRF No. IEC60950_1C
N/A
Page 40 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
B.7.4
Electric strength test; test voltage (V) ................. :
Fan motor is located in SELV
circuit.
B.8
Test for motors with capacitors
N/A
B.9
Test for three-phase motors
N/A
B.10
Test for series motors
N/A
N/A

Operating voltage (V) ........................................... :
C
Verdict
N/A
ANNEX C, TRANSFORMERS (see 1.5.4 and 5.3.3)
Evaluated in approved power supply.
Position ................................................................ :

Manufacturer ........................................................ :

Type ..................................................................... :

Rated values ....................................................... :

Method of protection ............................................. :

C.1
Overload test
N/A
C.2
Insulation
N/A
Protection from displacement of windings ............ :
N/A
D
ANNEX D, MEASURING INSTRUMENTS FOR TOUCH-CURRENT TESTS
(see 5.1.4)
P
D.1
Measuring instrument
P
D.2
Alternative measuring instrument
N/A
E
ANNEX E, TEMPERATURE RISE OF A WINDING (see 1.4.13)
N/A
F
ANNEX F, MEASUREMENT OF CLEARANCES AND CREEPAGE DISTANCES
(see 2.10 and Annex G)
Figure D.1 used.
P
Evaluated in approved power supply.
G
ANNEX G, ALTERNATIVE METHOD FOR DETERMINING MINIMUM
CLEARANCES
N/A
G.1
Clearances
N/A
G.1.1
General
N/A
G.1.2
Summary of the procedure for determining
minimum clearances
N/A
TRF No. IEC60950_1C
Page 41 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
G.2
Determination of mains transient voltage (V)
N/A
G.2.1
AC mains supply .................................................. :
N/A
G.2.2
Earthed d.c. mains supplies ................................. :
N/A
G.2.3
Unearthed d.c. mains supplies ............................ :
N/A
G.2.4
Battery operation .................................................. :
N/A
G.3
Determination of telecommunication network
transient voltage (V) ............................................. :
N/A
G.4
Determination of required withstand voltage (V)
N/A
G.4.1
Mains transients and internal repetitive peaks .... :
N/A
G.4.2
Transients from telecommunication networks ..... :
N/A
G.4.3
Combination of transients
N/A
G.4.4
Transients from cable distribution systems
N/A
G.5
Measurement of transient voltages (V)
N/A
a) Transients from a mains supply
N/A
For an a.c. mains supply
N/A
For a d.c. mains supply
N/A
b) Transients from a telecommunication network
N/A
G.6
Determination of minimum clearances ................ :
N/A
H
ANNEX H, IONIZING RADIATION (see 4.3.13)
N/A
J
ANNEX J, TABLE OF ELECTROCHEMICAL POTENTIALS (see 2.6.5.6)
Metal(s) used ....................................................... : Metals which the combination
electrochemical potential is
less than 0.6V
K
Result - Remark
ANNEX K, THERMAL CONTROLS (see 1.5.3 and 5.3.8)
Verdict
P

N/A
Approved thermistor used.
K.1
Making and breaking capacity
N/A
K.2
Thermostat reliability; operating voltage (V) ........ :
N/A
K.3
Thermostat endurance test; operating voltage (V)
.............................................................................. :
N/A
K.4
Temperature limiter endurance; operating voltage
(V) ........................................................................ :
N/A
K.5
Thermal cut-out reliability
N/A
TRF No. IEC60950_1C
Page 42 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
K.6
Stability of operation
TRF No. IEC60950_1C
Result - Remark
Verdict
N/A
Page 43 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
L
ANNEX L, NORMAL LOAD CONDITIONS FOR SOME TYPES OF ELECTRICAL
BUSINESS EQUIPMENT (see 1.2.2.1 and 4.5.2)
L.1
Typewriters
N/A
L.2
Adding machines and cash registers
N/A
L.3
Erasers
N/A
L.4
Pencil sharpeners
N/A
L.5
Duplicators and copy machines
N/A
L.6
Motor-operated files
N/A
L.7
Other business equipment
M
ANNEX M, CRITERIA FOR TELEPHONE RINGING SIGNALS (see 2.3.1)
N/A
M.1
Introduction
N/A
M.2
Method A
N/A
M.3
Method B
N/A
M.3.1
Ringing signal
N/A
M.3.1.1
Frequency (Hz) .................................................... :

M.3.1.2
Voltage (V) ........................................................... :

M.3.1.3
Cadence; time (s), voltage (V) ............................. :

M.3.1.4
Single fault current (mA) ...................................... :

M.3.2
Tripping device and monitoring voltage ............... :
N/A
M.3.2.1
Conditions for use of a tripping device or a
monitoring voltage
N/A
M.3.2.2
Tripping device
N/A
M.3.2.3
Monitoring voltage (V) .......................................... :
N/A
N
ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9,
6.2.2.1, 7.3.2, 7.4.3 and Clause G.5)
N/A
N.1
ITU-T impulse test generators
N/A
N.2
IEC 60065 impulse test generator
N/A
TRF No. IEC60950_1C
Result - Remark
The equipment is operated
according to the most
unfavorable way of operation.
Verdict
P
P
Page 44 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
P
ANNEX P, NORMATIVE REFERENCES
Q
ANNEX Q, Voltage dependent resistors (VDRs) (see 1.5.9.1)
Verdict

N/A
Evaluated in approved power supply.
a) Preferred climatic categories ........................... :
N/A
b) Maximum continuous voltage .......................... :
N/A
c) Pulse current .................................................... :
N/A
R
ANNEX R, EXAMPLES OF REQUIREMENTS FOR QUALITY CONTROL
PROGRAMMES
N/A
R.1
Minimum separation distances for unpopulated
coated printed boards (see 2.10.6.2)
N/A
R.2
Reduced clearances (see 2.10.3)
N/A
S
ANNEX S, PROCEDURE FOR IMPULSE TESTING (see 6.2.2.3)
N/A
S.1
Test equipment
N/A
S.2
Test procedure
N/A
S.3
Examples of waveforms during impulse testing
N/A
T
ANNEX T, GUIDANCE ON PROTECTION AGAINST INGRESS OF WATER
(see 1.1.2)
N/A

U
ANNEX U, INSULATED WINDING WIRES FOR USE WITHOUT INTERLEAVED
INSULATION (see 2.10.5.4)
N/A

V
ANNEX V, AC POWER DISTRIBUTION SYSTEMS (see 1.6.1)
P
V.1
Introduction
P
V.2
TN power distribution systems
P
W
ANNEX W, SUMMATION OF TOUCH CURRENTS
N/A
W.1
Touch current from electronic circuits
N/A
TRF No. IEC60950_1C
Page 45 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
W.1.1
Floating circuits
N/A
W.1.2
Earthed circuits
N/A
W.2
Interconnection of several equipments
N/A
W.2.1
Isolation
N/A
W.2.2
Common return, isolated from earth
N/A
W.2.3
Common return, connected to protective earth
N/A
X
ANNEX X, MAXIMUM HEATING EFFECT IN TRANSFORMER TESTS
(see clause C.1)
N/A
X.1
Determination of maximum input current
N/A
X.2
Overload test procedure
N/A
Y
ANNEX Y, ULTRAVIOLET LIGHT CONDITIONING TEST (see 4.3.13.3)
N/A
Y.1
Test apparatus ..................................................... :
N/A
Y.2
Mounting of test samples ..................................... :
N/A
Y.3
Carbon-arc light-exposure apparatus .................. :
N/A
Y.4
Xenon-arc light exposure apparatus .................... :
N/A
Z
ANNEX Z, OVERVOLTAGE CATEGORIES (see 2.10.3.2 and Clause G.2)
AA
ANNEX AA, MANDREL TEST (see 2.10.5.8)
BB
ANNEX BB, CHANGES IN THE SECOND EDITION
CC
ANNEX CC, Evaluation of integrated circuit (IC) current limiters
N/A
CC.1
General
N/A
CC.2
Test program 1……………………………………….:
N/A
CC.3
Test program 2……………………………………….:
N/A
TRF No. IEC60950_1C
Result - Remark
Verdict
P
N/A

Page 46 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
DD
ANNEX DD, Requirements for the mounting means of rack-mounted
equipment
N/A
DD.1
General
N/A
DD.2
Mechanical strength test, variable N………………..:
N/A
DD.3
Mechanical strength test, 250N, including end
stops……………………………………………………:
N/A
DD.4
Compliance……………………………………………:
N/A
EE
ANNEX EE, Household and home/office document/media shredders
N/A
EE.1
General
N/A
EE.2
Markings and instructions
N/A
Use of markings or symbols…………………………:
N/A
Information of user instructions, maintenance
and/or servicing instructions…………………………:
N/A
EE.3
Inadvertent reactivation test…………………………:
N/A
EE.4
Disconnection of power to hazardous moving
parts:
N/A
Use of markings or symbols…………………………:
N/A
Protection against hazardous moving parts
N/A
Test with test finger (Figure 2A)
……………………:
N/A
Test with wedge probe (Figure EE1 and EE2) ……:
N/A
EE.5
TRF No. IEC60950_1C
Result - Remark
Installed less than 1 m
Verdict
Page 47 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
1.5.1
TABLE: List of critical components
Object/part No.
DVD multi-drive
Manufacturer/
trademark
TEAC CORP
Result - Remark
Type/model
DVW5600S
Verdict
P
Technical data
12V, 5V,
40°C, class I
laser product
Standard
(Edition / year)
IEC 60950-1:
2005 + A1,
Mark(s) of
conformity1)
UL
(certificate: JP11109-UL,
report: E75017A53-CB-1)
EN 60950-1:
2006 + A11 + A1
TUV (license:
+ A12
R50254867,
report:
12030136)
12 Vdc, 5Vdc,
55°C
IEC/EN/UL
60950-1
System Fan (for Sunonwealth
PSD1207PTB1ventilation inside Electric Machine A
the enclosure)
Industry Co.,
Ltd.
DC 12V,
280mA,
44.3 CFM
EN 60950TUV (license:
1:2006+A11+A1 50171004),
+A12,
UL (E77551)
UL507
Fan (for CPU)
Everflow
R128015BU
Precision
Electronic (Dong
Guan) Co Ltd
DC 12V, 0.50A, UL 507
46.57 CFM
UL (E236658)
PCB
(motherboard)
Interchangeable
Interchangeable
Min V-1, 105°C UL 796
UL
Other PCBs
(network
interface card,
DDR card, PCI2
cable extender
PB-PEX16B-12,
front dual
USB2.0 card)
Interchangeable
Interchangeable
Min V-1, 105°C UL 796
UL
Hard disk drive
(HDD)
Interchangeable
TRF No. IEC60950_1C
Interchangeable
Tested within the
equipment
Page 48 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Internal Wiring
(between power
supply and PCB
motherboard)
Result - Remark
Verdict
interchangeable
interchangeable
FEP, PTFE,
UL 758
PVC, TFE,
neoprene,
polymide or
marked VW-1,
min 300V,
80°C, 18 AWG.
Wiring is fixed
by cable ties or
other means
UL
SATA cable (red Interchangeable
flat cable
between PCB
motherboard to
DVD drive or
HDD)
interchangeable
VW-1, 26 AWG, UL 758
80°C, 30V
UL (E189529)
Metal enclosure
---
dimension 473
mm X 430 mm
X 88 mm,
thickness 12
mm
---
Tested within
equipment
Insulating foil
Mianyang
PC1870
sheet (between Longhua Film Co
the bottom of
Ltd
motherboard and
internal
enclosure
bottom, color
black)
VTM-0, 80°C
UL 94
UL
Heat shrinkable
tube for
secondary
wiring, LED
indicators and
front power
switch for
motherboard
VW-1, min
150V, 125°C
UL 224
UL
---
Interchangeable
TRF No. IEC60950_1C
Interchangeable
Page 49 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Switching Power FSP Group Inc
Supply
Result - Remark
FSP400-60EVF
Rated input:
100-240Vac,
60-50Hz, 73.5A,
Rated output:
+3.3V/16A,
+5V/19A,
+12V1/16A,
+12V2/16A, 12V/0.3A,
+5Vsb/2A,
+3.3V &
5V/105W,
+12V1 &
+12V2/25A,
400W,
50°C,
Protection
Class 1
- Description:
PCB (motherboard)
Motherboard
Kontron
Technology A/S
CB (certificate:
JPTUV-046838,
report: 11030607
001),
UL 60950-1,
UL (E190414),
EN 609501:2006+A11+A1
+A12
TUV
(R 50129938,
report:
10022615)
Rating:
+3.3 Vdc, +
KTH81/Flex (a
5Vdc, +12 Vdc,
downgraded
-12Vdc
version of
(optional),
KTQ87/Flex with
60°C, class III,
lesser ports
attached to PCB input: SELV,
motherboard)
Output: SELV,
LPS (USB ports
and display
ports)
IEC 609501:2005 +
Am1:2009,
PTC thermistor Littelfuse Inc
or PTC resistor
(F14,F15,F16,F
17,F18,F19,F20,
F21,F22,F23,F2
4,F25,F26,F27,F
28,F29,F30)
(F24, F26 and
F27 optional on
KTH81/Flex)
1206L150PR
8Vdc, 1.5A
UL1434,
IEC60738-1
UL (E183209),
TUV (50119118)
PTC thermistor
or PTC resistor
(alternate)
1206L150TH
8Vdc, 1.5A
UL1434,
IEC60738-1
UL (E183209),
TUV (50119118)
Littelfuse Inc.
TRF No. IEC60950_1C
KTQ87/Flex,
IEC 60950-1:
2005 + A1,
Verdict
EN 60950-1:
2006 + A1
+A11+A12
UL (CB report
number:
E194252-A30CB-1, cert
number: DK36599-UL),
UL
(report number:
E194252-A30UL, E194252)
Page 50 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
PTC thermistor
or PTC resistor
(alternate)
PTTC
(Polytronics
Technology
Corp.)
PTC thermistor
or PTC resistor
(alternate)
TE (Tyco
NANOSMDC150 6Vdc, 1.5A
Electronics,
F-2
Raychem Circuit
Protection
Division)
SMD1206P150T 8Vdc, 1.5A
FT
NTC Thermistor Thinking
TSM0B224
(TH1, TH2)
Electronic
Industrial Co Ltd
220 kohm at
25°C
Lithium Battery
Rated 3.0 V,
max abnormal
charging
current 10 mA,
60°C, nonrechargable ,
max current
under
continuous
discharge =
4mA
Panasonic
CR-2032
UL 1434, IEC/EN UL (E201431),
60738-1,
TUV(50099121)
IEC/EN 60730-1
UL 1434,
UL (E74889)
EN60730-1
TUV (72112088)
UL1434,
UL (E138827),
EN 60539-1,
EN 60539-2,
EN 60730-1
UL1642
Supplementary information:
1)
Provided evidence ensures the agreed level of compliance. See OD-CB2039.
TRF No. IEC60950_1C
Verdict
TUV
(R 50167657)
UL (MH 12210)
Page 51 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
1.5.1
TABLE: Opto Electronic Devices
Manufacturer ............................................... :
Type............................................................. :
Separately tested ........................................ :
Bridging insulation ....................................... :
External creepage distance......................... :
Internal creepage distance .......................... :
Distance through insulation ......................... :
Tested under the following conditions ......... :
Input............................................................. :
Output .......................................................... :
supplementary information
Approved photo-coupler used in approved power supply.
TRF No. IEC60950_1C
Result - Remark
Verdict
N/A
Page 52 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
1.6.2
TABLE: Electrical data (in normal conditions)
Verdict
P
U (V)
I (A)
Irated (A)
P (W)
Fuse #
Ifuse (A)
Condition/status
90
1.2
---
105.3
*1
1.2
50Hz
90
1.3
---
113.4
*1
1.3
60Hz
100
1.2
4.5A
116.9
*1
1.2
50Hz
100
1.2
4.5A
115.2
*1
1.2
60Hz
240
0.5
4.5A
107.4
*1
0.5
50Hz
240
0.5
4.5A
104.6
*1
0.5
60Hz
264
0.5
---
106.2
*1
0.5
50Hz
264
0.5
---
106.6
*1
0.5
60Hz
Supplementary information:
*1: fuse of approved power supply
Tested with the following conditions below for the least favourable conditions, according to the
manufacturer.
-
burn-in software running
-
DVD multi-drive inserted with CD media.
-
connected output loads as below
1) Front USB 2.0 type connectors: 10 ohm resistors between 5V and ground
2) Rear USB 3.0 type connectors: 5 ohm resistors between 5V and ground
3) DisplayPort connector: to a monitor
2.1.1.5 c)
1)
N/A
TABLE: max. V, A, VA test
Voltage (rated)
(V)
Current (rated)
(A)
supplementary information:
Evaluation in approved power supply.
TRF No. IEC60950_1C
Voltage (max.)
(V)
Current (max.)
(A)
VA (max.)
(VA)
Page 53 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
2.1.1.5 c)
2)
TABLE: stored energy
Capacitance C (µF)
Result - Remark
Verdict
N/A
Voltage U (V)
Energy E (J)
supplementary information:
2.2
N/A
TABLE: evaluation of voltage limiting components in SELV circuits
Component (measured between)
max. voltage (V)
(normal operation)
V peak
Fault test performed on voltage limiting components
Voltage Limiting Components
V d.c.
Voltage measured (V) in SELV circuits
(V peak or V d.c.)
supplementary information:
Evaluation in approved power supply.
2.5
P
TABLE: Limited power sources
Circuit output tested: USB front and rear, DisplayPort
Note: Measured Uoc (V) with all load circuits disconnected:
Components
Sample No.
Uoc (V)
Isc (A)
VA
Meas.
Limit
Meas.
Limit
USB2.0 front
1
5.1
5.5
8
28.1
100
USB3.0 rear
1
5.1
3.0
8
15.3
100
DisplayPort
1
3.3
3.4
8
10.2
100
supplementary information:
Sc=Short circuit, Oc=Open circuit
Test voltage / frequency: 264V / 60 Hz
PTCs are used for the data ports, Isc is equal to ITRIP
Using each type of data ports as representative for other ports due to USB ports are using the same
voltage points. This also applies to display ports.
TRF No. IEC60950_1C
Page 54 of 94
Report No. 18005046 001
IEC 60950-1
Clause
2.6.3.4
Requirement + Test
Result - Remark
P
TABLE: Resistance of earthing measurement
Location
Resistance measured (mΩ)
Verdict
Comments
PE pin of AC inlet to top enclosure
40
32A, 2 minute, Vdrop = 1.29V
PE pin of AC inlet to rear enclosure (at
data ports area)
40
32A, 2 minute, Vdrop = 1.28V
PE pin of AC inlet to rear enclosure
(above build in power supply)
40
32A, 2 minute, Vdrop = 1.29V
PE pin of AC inlet to front enclosure
42
32A, 2 minute, Vdrop = 1.33V
PE pin of AC inlet to handle (front)
55
32A, 2 minute, Vdrop = 1.76V
PE pin of AC inlet to front cover
51
32A, 2 minute, Vdrop = 1.64V
PE pin of AC inlet to top enclosure
29
40A, 2 minute, Vdrop = 1.14V
PE pin of AC inlet to rear enclosure (at
data ports area)
30
40A, 2 minute, Vdrop = 1.18V
PE pin of AC inlet to rear enclosure
(above build in power supply)
30
40A, 2 minute, Vdrop = 1.20V
PE pin of AC inlet to front enclosure
29
40A, 2 minute, Vdrop = 1.17V
PE pin of AC inlet to handle (front)
37
40A, 2 minute, Vdrop = 1.47V
PE pin of AC inlet to front cover
55
40A, 2 minute, Vdrop = 2.18V
Supplementary information:
2.10.2
N/A
Table: working voltage measurement
Location
RMS voltage (V)
supplementary information:
Evaluation done in approved power supply.
TRF No. IEC60950_1C
Peak voltage (V) Comments
Page 55 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
N/A
2.10.3 and TABLE: Clearance and creepage distance measurements
2.10.4
Clearance (cl) and creepage
distance (cr) at/of/between:
U peak
(V)
U r.m.s.
(V)
Required cl
(mm)
cl
(mm)
Required cr
(mm)
cr
(mm)
Functional:
Basic/supplementary:
Reinforced:
Supplementary information:
Evaluation done in approved power supply.
2.10.5
P
TABLE: Distance through insulation measurements
Distance through insulation (DTI) at/of:
U peak
(V)
U rms
(V)
Test voltage
(V)
Required
DTI
(mm)
DTI
(mm)
Heat shrinkable tube for wiring, LED indicators and
power switch (functional insulation, 1 layer)
420
240
AC 1922
*(1)

0.30
Insulating foil sheet between the bottom of
motherboard and internal enclosure bottom (color
black, basic insulation, 1 layer)
420
240
AC 1922
*(1)

0.24
Supplementary information:
*(1) highest test voltage for basic insulation (primary to PE or primary to core or secondary to core)
obtained from the CB test report table 5.2 of the approved power supply
TRF No. IEC60950_1C
Page 56 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
4.3.8
TABLE: Batteries
Result - Remark
Verdict
P
The tests of 4.3.8 are applicable only when appropriate battery
data is not available
Refer below
P
Is it possible to install the battery in a reverse polarity position?
No, using special socket
P
Non-rechargeable batteries
Discharging
Meas.
current
Manuf.
Specs.
Max.
current
during
normal
condition
0.61 uA
0.2 mA
Max.
current
during
fault
condition
2.83 mA
4 mA
(1)
Unintentional
charging
Rechargeable batteries
Charging
Meas.
current
Manuf.
Specs.
Discharging
Meas.
current
Manuf.
Specs.
Reversed
charging
Meas.
current
Manuf.
Specs.
Prevented
0.13 mA
(2)
(1)
Worst case is short circuit point C (cathode) of diode D20 to ground (chassis).
(2)
Worst case is short circuit point A2 (anode) to C (cathode) of diode D20. Charged for 7 hours
Internal circuit prevents unintentional charging of a non-rechargeable battery.
For manufacturer data and data from UL database, refer to Lithium Battery on table 1.5.1 List of critical
components
A new battery is used for each test.
Test results:
Verdict
- Chemical leaks
No leaks
P
- Explosion of the battery
No explosion
P
- Emission of flame or expulsion of molten metal
No flame or molten metal
P
- Electric strength tests of equipment after completion of tests
See appended table 5.2
P
Supplementary information:
TRF No. IEC60950_1C
Page 57 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
4.3.8
TABLE: Batteries
Result - Remark
P
Battery category .......................................... :
Lithium
Manufacturer ............................................... :
Panasonic
Type / model ................................................ : CR-2032
Voltage ........................................................ : 3.0 Vdc
Capacity ...................................................... :
210 mAh
Tested and Certified by (incl. Ref. No.) ....... :
UL 1642
(MH 12210)
Circuit protection diagram:
MARKINGS AND INSTRUCTIONS (1.7.13 )
Location of replaceable battery
BAT1A on the motherboard
Language(s) …………………………………….: English
Close to the battery …………………………….: PCB, D20, R348
In the servicing instructions
……………………:
N/A
In the operating instructions …………………..: N/A
TRF No. IEC60950_1C
Verdict
Page 58 of 94
Report No. 18005046 001
IEC 60950-1
Clause
4.5
Requirement + Test
Result - Remark
Verdict
P
TABLE: Temperature rise measurements
Temperatures were measured according cl. 1.4.5. Test in condition A and B at continuous normal operation
as for power input measurements of table 1.6 resulted in highest temperature values.
Temperatures are calculated according cl. 1.4.12.3 with regard to the maximum ambient operation
temperature of
50
°C(Tma), as specified by the manufacturer.
test voltage(s) (V):
tamb1 (°C):
A:
A: 20.5
B: 19.3
Temperature of part/at:
(measured with thermocouples)
90 V,
50 Hz
tamb2 (°C):
B:
90 V,
A: 19.8
Measured
temperature at Tamb
60 Hz
B: 19.5
Calculated
temperature at Tma
Allowed
Tmax
(°C)
A
T (°C)
B
T (°C)
A
T (°C)
B
T (°C)
Enclosure Top cover (point above CPU fan)
29.1
29.6
59.3
60.1
70
Enclosure Left (point near ventilation inlet
system fan)
19.8
19.7
50.0
50.2
70
Enclosure Right (point near power supply)
24.7
24.7
54.3
55.2
70
Enclosure Front (point near USB port)
20.8
21.0
51.0
51.5
70
Enclosure Rear (point near USBLAN1 port)
31.4
31.8
61.6
62.3
70
Hard disk drive
35.8
36.1
66.0
66.6
70
DVD multi-drive (near rotating media)
29.3
29.8
59.5
60.3
70
Wire (internal, between motherboard PCB and
power supply)
33.1
33.5
63.3
64.0
80
Enclosure of power supply (near its inlet fan)
29.6
29.9
59.8
60.4
70
Appliance inlet
28.1
28.6
58.3
59.1
70
Top of Motherboard PCB (near heatsink of
CPU)
35.2
35.6
65.4
66.1
105
Heatsink fins of CPU
35.6
35.9
65.8
66.4
70
PTC fuse (F21) on motherboard for USBLAN2
port
35.5
36.0
65.7
66.5
85
USBLAN2 port at rear of enclosure
34.5
35.1
64.7
65.6
70
USB2.0 port at front of enclosure
20.5
20.8
50.7
51.3
70
DisplayPort DP1
33.9
34.4
64.1
64.9
70
Ventilation system fan at front of enclosure
23.0
23.5
53.2
54.0
70
Power switch surface of power supply
31.0
31.3
61.2
61.8
95
TRF No. IEC60950_1C
Page 59 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Surface of Power switch ( for motherboard,
located at front of enclosure)
20.7
21.1
50.9
51.6
95
Network card (top of this PCB facing the
motherboard)
29.3
29.6
59.5
60.1
130
Handle at the front side of the enclosure
19.8
19.6
50.0
50.1
60
Supplementary information:
The temperatures were measured under worst case normal mode defined in 1.2.2.1 and as described in
appended table 1.6.2 and at voltages as described above.
- Temperature rise was measured with thermocouples.
- All values for T(°C) are re-calculated from Tamb respectively.
Evaluation is also done in approved power supply.
Temperatures measured with winding resistance method: Not used
temperature T of winding:
(winding resistance method)
Supplementary information:
TRF No. IEC60950_1C
(V)
R1 ()
R2 ()
T (C)
allowed
Tmax (C)
insulation
class
Page 60 of 94
Report No. 18005046 001
IEC 60950-1
Clause
4.5
Requirement + Test
Result - Remark
Verdict
P
TABLE: Temperature rise measurements
Temperatures were measured according cl. 1.4.5. Test in condition A and B at continuous normal operation
as for power input measurements of table 1.6 resulted in highest temperature values.
Temperatures are calculated according cl. 1.4.12.3 with regard to the maximum ambient operation
temperature of
50
°C(Tma), as specified by the manufacturer.
test voltage(s) (V):
tamb1 (°C):
A:
A: 19.8
B: 19.7
Temperature of part/at:
(measured with thermocouples)
264 V,
50 Hz
tamb2 (°C):
B:
264 V,
A: 19.8
Measured
temperature at Tamb
60 Hz
B: 23.6
Calculated
temperature at Tma
Allowed
Tmax
(°C)
A
T (°C)
B
T (°C)
A
T (°C)
B
T (°C)
Enclosure Top cover (point above CPU fan)
28.9
32.3
59.1
58.6
70
Enclosure Left (point near ventilation inlet
system fan)
19.8
23.6
50.0
50.0
70
Enclosure Right (point near power supply)
24.5
26.6
54.7
53.0
70
Enclosure Front (point near USB port)
21.2
24.8
51.4
51.2
70
Enclosure Rear (point near USBLAN1 port)
31.3
34.1
61.5
60.5
70
Hard disk drive
35.2
37.1
65.4
63.5
70
DVD multi-drive (near rotating media)
29.4
31.4
59.6
57.8
70
Wire (internal, between motherboard PCB and
power supply)
32.9
35.8
63.1
62.2
80
Enclosure of power supply (near its inlet fan)
29.4
31.8
59.6
57.7
70
Appliance inlet
27.4
29.3
57.6
55.7
70
Top of Motherboard PCB (near heatsink of
CPU)
35.0
38.4
65.2
64.8
105
Heatsink fins of CPU
35.3
38.7
65.5
65.1
70
PTC fuse (F21) on motherboard for USBLAN2
port
35.4
38.7
65.6
65.1
85
USBLAN2 port at rear of enclosure
34.5
37.6
64.7
64.0
70
USB2.0 port at front of enclosure
20.9
24.9
51.1
51.3
70
DisplayPort DP1
33.6
36.6
63.8
63.0
70
Ventilation system fan at front of enclosure
23.3
27.9
53.5
54.3
70
Power switch surface of power supply
29.9
32.0
60.1
58.4
95
TRF No. IEC60950_1C
Page 61 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
Surface of Power switch ( for motherboard,
located at front of enclosure)
21.9
25.0
52.1
51.4
95
Network card (top of this PCB facing the
motherboard)
29.4
32.2
59.6
58.6
130
Handle at the front side of the enclosure
19.8
23.6
50.0
50.0
60
Supplementary information:
The temperatures were measured under worst case normal mode defined in 1.2.2.1 and as described in
appended table 1.6.2 and at voltages as described above.
- Temperature rise was measured with thermocouples.
- All values for T(°C) are re-calculated from Tamb respectively.
Evaluation is also done in approved power supply.
Temperatures measured with winding resistance method: Not used
temperature T of winding:
(winding resistance method)
Supplementary information:
TRF No. IEC60950_1C
(V)
R1 ()
R2 ()
T (C)
allowed
Tmax (C)
insulation
class
Page 62 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
4.5.5
TABLE: Ball pressure test of thermoplastic parts
P
Allowed impression diameter (mm) ..................... :  2 mm

Part
Verdict
Test temperature Impression diameter
(mm)
(C)
CPU fan housing (material:PBT plastic)
125
1.5
Supplementary information: Tested for UL approved CPU fan
4.6.1, 4.6.2 Table: Enclosure opening measurements
Location
Top, bottom
Size (mm)
--
Front side
3.80 mm
Right side
--
P
Comments
No openings
Air filter assembly holes after the filter
No openings except hole for screws
Left side
6.89 mm
Several circle openings. No hazardous parts
within 5° projection area from the openings.
Rear
3.80 mm
Circle openings for ventilation.
Supplementary information: Refer to clause 4.6.1 and 4.6.2.
Thickness of metal enclosure > 1.0 mm.
TRF No. IEC60950_1C
Page 63 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
4.7
TABLE: Resistance to fire
Part
Result - Remark
Verdict
P
Manufacturer of
material
Type of material
Thickness Flammability
(mm)
class
Evidence
Supplementary information: see table 1.5.1 for details.
5.1
P
TABLE: touch current measurement
Measured between:
Measured
(mA)
Limit
(mA)
Comments/conditions
metal enclosure (rear ventilation
openings)
1.42
3.5
Polarity normal, Switch “e” opened.
metal enclosure (rear ventilation
openings)
1.5
3.5
Polarity reverse, Switch “e” opened.
output connector
0.0
0.25
Polarity normal, Switch “e” closed.
output connector
0.0
0.25
Polarity reverse, Switch “e” closed.
terminal A connected to…
supplementary information:
Test voltage / frequency: 264V / 60 Hz
Polarity normal :L/N, reverse: N/L
Evaluation also done in approved power supply.
TRF No. IEC60950_1C
Page 64 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
5.2
TABLE: Electric strength tests, impulse tests and voltage surge tests
Test voltage applied between:
Result - Remark
Verdict
Voltage shape Test voltage
(AC, DC,
(V)
impulse, surge)
P
Breakdo
wn
Yes / No
Functional:
--Basic/supplementary:
Insulating foil sheet (between the bottom of motherboard and
internal enclosure bottom, color black)
AC
1922
*(1)
No
Heat shrinkable/insulation tube for wiring, LED indicators and
power switch
AC
1922
*(1)
No
Primary to Ground (PE)
AC
1922
*(1)
No
AC
3000
No
Reinforced:
Primary to Secondary
Supplementary information:
Evaluation also done in approved power supply.
*(1) highest test voltage for basic insulation (primary to PE or primary to core or secondary to core)
obtained from the CB test report table 5.2 of the approved power supply
TRF No. IEC60950_1C
Page 65 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
Result - Remark
5.3
TABLE: Fault condition tests
Verdict
P
Ambient temperature (C) ................................... :
See below.

Power source for EUT: Manufacturer, model/type,
output rating ......................................................... :
--

Component
No.
Fault
Supply
voltage
(V)
Test
time
Fuse #
Fuse
current
(A)
Observation
Ventilation
openings at
rear
enclosure
B
264V,
60 Hz
4 hr
F1
0.46A
Fan outlet of the power supply
(located at the rear enclsoure) is
also blocked.
Temperature saturated within
limits. No hazards observed.
Ambient = 24.3C, PCB top
surface on Motherboard =
42.4C, CPU heatsink center =
47.1C, Battery surface = 40.7C
CPU fan
L
264V,
60 Hz
7 hr
F1
0.49A
Temperature saturated within
limits. No hazards observed.
Ambient = 20.3C,
PCB top surface on Motherboard
= 43.9C,
CPU heatsink center = 82.4C,
Battery surface = 51.9C,
CPU fan = 86.9C,
System Fan front = 25.4C,
Ambient (Inside) = 21.7C
Front
system fan
L
264V,
60 Hz
7 hr
F1
0.45A
Temperature saturated within
limits. No hazards observed.
Ambient = 20.2C,
PCB top surface on Motherboard
= 42.3C,
CPU heatsink center = 46.0C,
Battery surface = 39.8C,
CPU fan = 50.6C,
System Fan front = 38.5C,
Ambient (Inside) = 24.3C
Supplementary information:
S = shorted, O=open, OL = overloaded, B= Blocked, L = Locked, in continuous operation,
Charging = C, Dis-charging = D
The insulation system could withstand the dielectric strength after fault conditions.
Other evaluation also done in approved power supply.
TRF No. IEC60950_1C
Page 66 of 94
Report No. 18005046 001
IEC 60950-1
Clause
Requirement + Test
C.2
TABLE: transformers
Loc.
Tested insulation
Result - Remark
Verdict
N/A
Working
voltage
peak / V
Working
voltage
rms / V
(2.10.2)
(2.10.2)
Require
d
electric
strength
Required
clearance
/ mm
Required
distance
thr. insul.
(2.10.3)
Required
creepage
distance /
mm
(2.10.4)
Measured
clearance
/ mm
Measured
creepage
dist./ mm
Measured
distance
thr. insul.
/ mm;
number of
layers
(2.10.5)
(5.2)
Loc.
Tested insulation
Test
voltage/
V
supplementary information:
Evaluation done in approved power supply.
C.2
TABLE: transformers
Transformer
TRF No. IEC60950_1C
N/A
Page 67 of 94
Report No. 18005046 001
EN 60950-1
Clause
Requirement + Test
Result - Remark
Verdict
List of test equipment used:
(Note: This is an example of the required attachment. Other forms with a different layout but containing
similar information are also acceptable.)
Clause
Measurement /
testing
Testing / measuring equipment /
material used
No listing of test equipment used necessary for chosen test procedure.
TRF No. IEC60950_1C
Range used
Calibration
date
Page 68 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
EUROPEAN GROUP DIFFERENCES AND NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to ............... : EN 60950-1:2006/A11:2009/A1:2010/A12:2011
Attachment Form No...................... : EU_GD_IEC60950_1C_II
Attachment Originator ................... : SGS Fimko Ltd
Master Attachment ......................... : Date 2011-08
Copyright © 2011 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
EN 60950-1:2006/A11:2009/A1:2010/A12:2011 – CENELEC COMMON MODIFICATIONS
Contents
General
Add the following annexes:
Annex ZA (normative)
Normative references to international
publications with their corresponding European
publications
Annex ZB (normative)
Special national conditions
Delete all the “country” notes in the reference document (IEC 60950-1:2005)
according to the following list:
1.4.8 Note 2
1.5.8 Note 2
2.2.3 Note
2.3.2.1 Note 2
2.7.1 Note
3.2.1.1 Note
4.3.6 Note 1 & 2
4.7.3.1Note 2
6
Note 2 & 5
6.2.2 Note
7.1
Note 3
G.2.1 Note 2
General
(A1:2010)
P
1.5.1
1.5.9.4
2.2.4
2.3.4
2.10.3.2
3.2.4
4.7
5.1.7.1
6.1.2.1
6.2.2.1
7.2
Annex H
Note 2 & 3 1.5.7.1
Note
Note
1.7.2.1
Note 4, 5 & 6
Note
2.3.2
Note
Note 2
2.6.3.3
Note 2 & 3
Note 2
2.10.5.13
Note 3
Note 3.
2.5.1
Note 2
Note 4
4.7.2.2
Note
Note 3 & 4 5.3.7
Note 1
Note 2
6.1.2.2
Note
Note 2
6.2.2.2
Note
Note
7.3
Note 1 & 2
Note 2
Delete all the “country” notes in the reference document (IEC 609501:2005/A1:2010) according to the following list:
1.5.7.1
Note
6.2.2.1
Note 2
P
6.1.2.1
EE.3
Note 2
Note
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
P
Page 69 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
1.3.Z1
Add the following subclause:
Result - Remark
Verdict
N/A
1.3.Z1 Exposure to excessive sound pressure
The apparatus shall be so designed and
constructed as to present no danger when used for
its intended purpose, either in normal operating
conditions or under fault conditions, particularly
providing protection against exposure to excessive
sound pressures from headphones or earphones.
NOTE Z1 A new method of measurement is
described in EN 50332-1, Sound system
equipment:
Headphones and earphones associated with
portable audio equipment - Maximum sound
pressure level measurement methodology and limit
considerations - Part 1: General method for “one
package equipment”, and in EN 50332-2, Sound
system equipment: Headphones and earphones
associated with portable audio equipment Maximum sound pressure level measurement
methodology and limit considerations - Part 2:
Guidelines to associate sets with headphones
coming from different manufacturers.
(A12:2011)
In EN 60950-1:2006/A12:2011
Deleted.
P
Delete the addition of 1.3.Z1 / EN 60950-1:2006
Delete the definition 1.2.3.Z1 / EN 60950-1:2006
/A1:2010
1.5.1
Add the following NOTE:
P
NOTE Z1 The use of certain substances in
electrical and electronic equipment is restricted
within the EU: see Directive 2002/95/EC
1.7.2.1
(A1:2010)
In addition, for a PORTABLE SOUND SYSTEM, the
instructions shall include a warning that excessive
sound pressure from earphones and headphones
can cause hearing loss.
N/A
1.7.2.1
(A12.2011)
In EN 60950-1:2006/A12:2011
Delete NOTE Z1 and the addition for Portable
Sound System.
Add the following clause and annex to the existing
standard and amendments.
N/A
Zx Protection against excessive sound pressure from personal music players
N/A
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 70 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Zx.1 General
This sub-clause specifies requirements for
protection against excessive sound pressure from
personal music players that are closely coupled to
the ear. It also specifies requirements for
earphones and headphones intended for use with
personal music players.
A personal music player is a portable equipment
for personal use, that:
- is designed to allow the user to listen to recorded
or broadcast sound or video; and
- primarily uses headphones or earphones that can
be worn in or on or around the ears; and
allows the user to walk around while in use.
NOTE 1 Examples are hand-held or body-worn portable CD
players, MP3 audio players, mobile phones with MP3 type
features, PDA’s or similar equipment.
A personal music player and earphones or
headphones intended to be used with personal
music players shall comply with the requirements
of this sub-clause.
The requirements in this sub-clause are valid for
music or video mode only.
The requirements do not apply:
- while the personal music player is connected to
an external amplifier; or
while the headphones or earphones are not
used.
NOTE 2 An external amplifier is an amplifier which is not part of
the personal music player or the listening device, but which is
intended to play the music as a standalone music player.
The requirements do not apply to:
- hearing aid equipment and professional
equipment;
NOTE 3 Professional equipment is equipment sold through
special sales channels. All products sold through normal
electronics stores are considered not to be professional
equipment.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Verdict
N/A
Page 71 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
- analogue personal music players (personal
music players without any kind of digital
processing of the sound signal) that are
brought to the market before the end of 2015.
Verdict
N/A
NOTE 4 This exemption has been allowed because this
technology is falling out of use and it is expected that within a
few years it will no longer exist. This exemption will not be
extended to other technologies.
For equipment which is clearly designed or
intended for use by young children, the limits of EN
71-1 apply.
Zx.2 Equipment requirements
No safety provision is required for equipment that
complies with the following:
-
equipment provided as a package (personal
music player with its listening device), where the
acoustic output LAeq,T is ≤ 85 dBA measured
while playing the fixed “programme simulation
noise” as described in EN 50332-1; and
- a personal music player provided with an
analogue electrical output socket for a listening
device, where the electrical output is ≤ 27 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
as described in EN 50332-1.
NOTE 1 Wherever the term acoustic output is used in this
clause, the 30 s A-weighted equivalent sound pressure level
LAeq,T is meant. See also Zx.5 and Annex Zx.
All other equipment shall:
a) protect the user from unintentional acoustic
outputs exceeding those mentioned above; and
b) have a standard acoustic output level not
exceeding those mentioned above, and
automatically return to an output level not
exceeding those mentioned above when the
power is switched off; and
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
Page 72 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
c) provide a means to actively inform the user of
the increased sound pressure when the
equipment is operated with an acoustic output
exceeding those mentioned above. Any means
used shall be acknowledged by the user before
activating a mode of operation which allows for
an acoustic output exceeding those mentioned
above. The acknowledgement does not need to
be repeated more than once every 20 h of
cumulative listening time; and
NOTE 2 Examples of means include visual or audible signals.
Action from the user is always required.
NOTE 3 The 20 h listening time is the accumulative listening
time, independent how often and how long the personal music
player has been switched off.
d) have a warning as specified in Zx.3; and
e) not exceed the following:
1) equipment provided as a package (player
with Its listening device), the acoustic output
shall be ≤ 100 dBA measured while playing the
fixed “programme simulation noise” described
in EN 50332-1; and
2) a personal music player provided with an
analogue electrical output socket for a listening
device, the electrical output shall be ≤ 150 mV
measured as described in EN 50332-2, while
playing the fixed “programme simulation noise”
described in EN 50332-1.
For music where the average sound pressure (long
term LAeq,T) measured over the duration of the
song is lower than the average produced by the
programme simulation noise, the warning does not
need to be given as long as the average sound
pressure of the song is below the basic limit of 85
dBA. In this case T becomes the duration of the
song.
NOTE 4 Classical music typically has an average sound
pressure (long term LAeq,T) which is much lower than the average
programme simulation noise. Therefore, if the player is capable
to analyse the song and compare it with the programme
simulation noise, the warning does not need to be given as long
as the average sound pressure of the song is below the basic
limit of 85 dBA.
For example, if the player is set with the programme simulation
noise to 85 dBA, but the average music level of the song is only
65 dBA, there is no need to give a warning or ask an
acknowledgement as long as the average sound level of the
song is not above the basic limit of 85 dBA.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Verdict
N/A
Page 73 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Zx.3 Warning
The warning shall be placed on the equipment, or
on the packaging, or in the instruction manual and
shall consist of the following:
- the symbol of Figure 1 with a minimum height of
5 mm; and the following wording, or similar:
Verdict
N/A
“To prevent possible hearing damage, do not listen
at high volume levels for long periods.”
Figure 1 – Warning label (IEC 60417-6044)
Alternatively, the entire warning may be given
through the equipment display during use, when
the user is asked to acknowledge activation of the
higher level.
Zx.4 Requirements for listening devices (headphones and earphones)
N/A
Zx.4.1 Wired listening devices with analogue
input
N/A
With 94 dBA sound pressure output LAeq,T, the
input voltage of the fixed “programme simulation
noise” described in EN 50332-2 shall be ≥ 75 mV.
This requirement is applicable in any mode where
the headphones can operate (active or
passive), including any available setting (for
example built-in volume level control).
NOTE The values of 94 dBA – 75 mV correspond with 85dBA –
27 mV and 100 dBA – 150 mV.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 74 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Zx.4.2 Wired listening devices with digital input
Verdict
N/A
With any playing device playing the fixed
“programme simulation noise” described in EN
50332-1 (and respecting the digital interface
standards, where a digital interface standard exists
that specifies the equivalent acoustic level), the
acoustic output LAeq,T of the listening device shall
be ≤ 100 dBA.
This requirement is applicable in any mode where
the headphones can operate, including any
available setting (for example built-in volume level
control, additional sound feature like equalization,
etc.).
NOTE An example of a wired listening device with digital input is
a USB headphone.
Zx.4.3 Wireless listening devices
In wireless mode:
- with any playing and transmitting device playing
the fixed programme simulation noise
described in EN 50332-1; and
- respecting the wireless transmission standards,
where an air interface standard exists that
specifies the equivalent acoustic level; and
- with volume and sound settings in the listening
device (for example built-in volume level
control, additional sound feature like
equalization, etc.) set to the combination of
positions that maximize the measured
acoustic output for the abovementioned
programme simulation noise, the acoustic
output LAeq,T of the listening device shall be ≤
100 dBA.
N/A
NOTE An example of a wireless listening device is a Bluetooth
headphone.
Zx.5 Measurement methods
Measurements shall be made in accordance with
EN 50332-1 or EN 50332-2 as applicable. Unless
stated otherwise, the time interval T shall be 30 s.
NOTE Test method for wireless equipment provided without
listening device should be defined.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
Page 75 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
2.7.1
Replace the subclause as follows:
Replaced.
Verdict
P
Basic requirements
Evaluated in approved power
To protect against excessive current, short-circuits supply which complied with
and earth faults in PRIMARY CIRCUITS, protective item a)
devices shall be included either as integral parts of
the equipment or as parts of the building
installation, subject to the following, a), b) and c):
a) except as detailed in b) and c), protective
devices necessary to comply with the requirements
of 5.3 shall be included as parts of the equipment;
b) for components in series with the mains input to
the equipment such as the supply cord, appliance
coupler, r.f.i. filter and switch, short-circuit and
earth fault protection may be provided by protective
devices in the building installation;
c) it is permitted for PLUGGABLE EQUIPMENT
TYPE B or PERMANENTLY CONNECTED
EQUIPMENT, to rely on dedicated overcurrent and
short-circuit protection in the building installation,
provided that the means of protection, e.g. fuses or
circuit breakers, is fully specified in the installation
instructions.
N/A
If reliance is placed on protection in the building
installation, the installation instructions shall so
state, except that for PLUGGABLE EQUIPMENT
TYPE A the building installation shall be regarded
as providing protection in accordance with the
rating of the wall socket outlet.
2.7.2
This subclause has been declared ‘void’.
N/A
3.2.3
Delete the NOTE in Table 3A, and delete also in
this table the conduit sizes in parentheses.
N/A
3.2.5.1
Replace
N/A
“60245 IEC 53” by “H05 RR-F”;
“60227 IEC 52” by “H03 VV-F or
H03 VVH2-F”;
“60227 IEC 53” by “H05 VV-F or
H05 VVH2-F2”.
In Table 3B, replace the first four lines by the
following:
Up to and including 6 |
0,75 a) |
b)
Over 6 up to and including 10| (0,75)
1,0 |
Over 10 up to and including 16| (1,0) c) 1,5
|
In the conditions applicable to Table 3B delete the
words “in some countries” in condition a).
In NOTE 1, applicable to Table 3B, delete the
second sentence.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 76 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
3.3.4
In Table 3D, delete the fourth line: conductor sizes
for 10 to 13 A, and replace with the following:
Result - Remark
Verdict
N/A
Over 10 up to and including 16 | 1,5 to 2,5 | 1,5 to 4
|
Delete the fifth line: conductor sizes for 13 to 16 A
4.3.13.6
(A1:2010)
Replace the existing NOTE by the following:
N/A
NOTE Z1 Attention is drawn to:
1999/519/EC: Council Recommendation on the
limitation of exposure of the general public to
electromagnetic fields 0 Hz to 300 GHz, and
2006/25/EC: Directive on the minimum health and
safety requirements regarding the exposure of
workers to risks arising from physical agents
(artifical optical radiation).
Annex H
Standards taking into account mentioned
Recommendation and Directive which demonstrate
compliance with the applicable EU Directive are
indicated in the OJEC.
N/A
Replace the last paragraph of this annex by:
N/A
At any point 10 cm from the surface of the
OPERATOR ACCESS AREA, the dose rate shall
not exceed 1 μSv/h (0,1 mR/h) (see NOTE).
Account is taken of the background level.
Replace the notes as follows:
NOTE These values appear in Directive
96/29/Euratom.
Delete NOTE 2.
Bibliography Additional EN standards.

ZA

NORMATIVE REFERENCES TO INTERNATIONAL PUBLICATIONS WITH
THEIR CORRESPONDING EUROPEAN PUBLICATIONS
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 77 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
1.2.4.1
In Denmark, certain types of Class I appliances
(see 3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted into
Danish socket-outlets.
N/A
1.2.13.14
In Norway and Sweden, for requirements see
1.7.2.1 and 7.3 of this annex.
No cable distribution
systems
N/A
1.5.7.1
In Finland, Norway and Sweden, resistors
bridging BASIC INSULATION in CLASS I
PLUGGABLE EQUIPMENT TYPE A must comply
with the requirements in 1.5.7.1. In addition when a
single resistor is used, the resistor must withstand
the resistor test in 1.5.7.2.
Evaluated in approved
power supply. No such
resistor bridging basic
insulation.
N/A
1.5.8
In Norway, due to the IT power system used (see
annex V, Figure V.7), capacitors are required to be
rated for the applicable line-to-line voltage (230 V).
N/A
1.5.9.4
In Finland, Norway and Sweden, the third dashed
sentence is applicable only to equipment as
defined in 6.1.2.2 of this annex.
N/A
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 78 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
1.7.2.1
In Finland, Norway and Sweden, CLASS I
PLUGGABLE EQUIPMENT TYPE A intended for
connection to other equipment or a network shall, if
safety relies on connection to protective earth or if
surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet.
Result - Remark
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
In Norway and Sweden, the screen of the cable
distribution system is normally not earthed at the
entrance of the building and there is normally no
equipotential bonding system within the building.
Therefore the protective earthing of the building
installation need to be isolated from the screen of a
cable distribution system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator, which
may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and Swedish
language respectively, depending on in what
country the equipment is intended to be used in:
“Equipment connected to the protective earthing of
the building installation through the mains
connection or through other equipment with a
connection to protective earthing – and to a cable
distribution system using coaxial cable, may in
some circumstances create a fire hazard.
Connection to a cable distribution system has
therefore to be provided through a device providing
electrical isolation below a certain frequency range
(galvanic isolator, see EN 60728-11).”
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Verdict
N/A
Page 79 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Verdict
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60 Hz,
for 1 min.
Translation to Norwegian (the Swedish text will
also be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet
utstyr – og er tilkoplet et kabel-TV nett, kan
forårsake brannfare. For å unngå dette skal det
ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret og
kabel- TV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via jordat
vägguttag och/eller via annan
utrustning och samtidigt är kopplad till kabel-TV nät
kan i vissa fall medfőra risk főr
brand. Főr att undvika detta skall vid anslutning av
utrustningen till kabel-TV nät
galvanisk isolator finnas mellan utrustningen och
kabel-TV nätet.”
1.7.5
In Denmark, socket-outlets for providing power to No socket outlet
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For
STATIONARY EQUIPMENT the socket-outlet shall
be in accordance with Standard Sheet DK 1-1b or
DK 1-5a.
N/A
For CLASS II EQUIPMENT the socket outlet shall
be in accordance with Standard Sheet DKA 1-4a.
2.2.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
N/A
2.3.2
In Finland, Norway and Sweden there are
additional requirements for the insulation. See
6.1.2.1 and 6.1.2.2 of this annex.
No TNV
N/A
2.3.4
In Norway, for requirements see 1.7.2.1, 6.1.2.1
and 6.1.2.2 of this annex.
No TNV
N/A
2.6.3.3
In the United Kingdom, the current rating of the
circuit shall be taken as 13 A, not 16 A.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
Page 80 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
2.7.1
In the United Kingdom, to protect against
excessive currents and short-circuits in the
PRIMARY CIRCUIT of DIRECT PLUG-IN
EQUIPMENT, tests according to 5.3 shall be
conducted, using an external protective device
rated 30 A or 32 A. If these tests fail, suitable
protective devices shall be included as integral
parts of the DIRECT PLUG-IN EQUIPMENT, so
that the requirements of 5.3 are met.
2.10.5.13
In Finland, Norway and Sweden, there are
additional requirements for the insulation, see
6.1.2.1 and 6.1.2.2 of this annex.
3.2.1.1
In Switzerland, supply cords of equipment having
a RATED CURRENT not exceeding 10 A shall be
provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of the following dimension
sheets:
Result - Remark
Verdict
N/A
No TNV.
SEV 6532-2.1991 Plug Type 15
3P+N+PE 250/400 V, 10 A
SEV 6533-2.1991 Plug Type 11
L+N
250 V, 10 A
SEV 6534-2.1991 Plug Type 12
L+N+PE
250 V, 10 A
In general, EN 60309 applies for plugs for currents
exceeding 10 A. However, a 16 A plug and socketoutlet system is being introduced in Switzerland,
the plugs of which are according to the following
dimension sheets, published in February 1998:
SEV 5932-2.1998: Plug Type 25 , 3L+N+PE
230/400 V, 16 A
SEV 5933-2.1998:Plug Type 21, L+N, 250 V, 16A
SEV 5934-2.1998: Plug Type 23, L+N+PE 250 V,
16 A
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
N/A
Page 81 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
3.2.1.1
In Denmark, supply cords of single-phase
equipment having a rated current not exceeding13
A shall be provided with a plug according to the
Heavy Current Regulations, Section 107-2-D1.
Result - Remark
Verdict
N/A
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules
shall be provided with a plug in accordance with
standard sheet DK 2-1a or DK 2-5a.
If poly-phase equipment and single-phase
equipment having a RATED CURRENT exceeding
13 A is provided with a supply cord with a plug, this
plug shall be in accordance with the Heavy Current
Regulations, Section 107-2-D1 or EN 60309-2.
3.2.1.1
In Spain, supply cords of single-phase equipment
having a rated current not exceeding 10 A shall be
provided with a plug according to UNE
20315:1994.
N/A
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be provided
with a plug according to UNE-EN 50075:1993.
CLASS I EQUIPMENT provided with socket-outlets
with earth contacts or which are intended to be
used in locations where protection against indirect
contact is required according to the wiring rules,
shall be provided with a plug in accordance with
standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
3.2.1.1
In the United Kingdom, apparatus which is fitted
with a flexible cable or cord and is designed to be
connected to a mains socket conforming to BS
1363 by means of that flexible cable or cord and
plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 The Plugs and Sockets etc. (Safety) Regulations
1994, unless exempted by those regulations.
NOTE ‘Standard plug’ is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved conversion
plug.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
Page 82 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Verdict
3.2.1.1
In Ireland, apparatus which is fitted with a flexible
cable or cord and is designed to be connected to a
mains socket conforming to I.S. 411 by means of
that flexible cable or cord and plug, shall be fitted
with a 13 A plug in accordance with Statutory
Instrument 525:1997 - National Standards
Authority of Ireland (section 28) (13 A Plugs and
Conversion Adaptors for Domestic Use)
Regulations 1997.
N/A
3.2.4
In Switzerland, for requirements see 3.2.1.1 of this
annex.
N/A
3.2.5.1
In the United Kingdom, a power supply cord with
conductor of 1,25 mm2 is allowed for equipment
with a rated current over 10 A and up to and
including 13 A.
N/A
3.3.4
In the United Kingdom, the range of conductor
sizes of flexible cords to be accepted by terminals
for equipment with a RATED CURRENT of over 10
A up to and including 13 A is:
N/A
• 1,25 mm2 to 1,5 mm2 nominal cross-sectional
area.
4.3.6
In the United Kingdom, the torque test is
performed using a socket outlet complying with BS
1363 part 1:1995, including Amendment 1:1997
and Amendment 2:2003 and the plug part of
DIRECT PLUG-IN EQUIPMENT shall be assessed
to BS 1363: Part 1, 12.1, 12.2, 12.3, 12.9, 12.11,
12.12, 12.13, 12.16 and 12.17, except that the test
of 12.17 is performed at not less than 125 °C.
Where the metal earth pin is replaced by an
Insulated Shutter Opening Device (ISOD), the
requirements of clauses 22.2 and 23 also apply.
N/A
4.3.6
In Ireland, DIRECT PLUG-IN EQUIPMENT is
known as plug similar devices. Such devices shall
comply with Statutory Instrument 526:1997 National Standards Authority of Ireland (Section
28) (Electrical plugs, plug similar devices and
sockets for domestic use) Regulations, 1997.
N/A
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 83 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
5.1.7.1
In Finland, Norway and Sweden TOUCH
CURRENT measurement results exceeding 3,5
mA r.m.s. are permitted only for the following
equipment:
Result - Remark
Verdict
N/A
• STATIONARY PLUGGABLE EQUIPMENT TYPE
A that
is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential bonding
has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
is provided with instructions for the
installation of that conductor by a SERVICE
PERSON;
• STATIONARY PLUGGABLE EQUIPMENT TYPE
B;
• STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
6.1.2.1
(A1:2010)
In Finland, Norway and Sweden, add the
following text between the first and second
paragraph of the compliance clause:
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
two layers of thin sheet material, each of
which shall pass the electric strength test below, or
one layer having a distance through
insulation of at least 0,4 mm, which shall pass the
electric strength test below.
Alternatively for components, there is no distance
through insulation requirements for the insulation
consisting of an insulating compound completely
filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below and
in addition
passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test voltage
of 1,5 kV.
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
N/A
Page 84 of 94
Report No. 18005046 001
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Clause
Requirement + Test
Result - Remark
Verdict
It is permitted to bridge this insulation with an
optocoupler complying with 2.10.5.4 b).
It is permitted to bridge this insulation with a
capacitor complying with EN 60384-14:2005,
subclass Y2.
A capacitor classified Y3 according to
EN 60384-14:2005, may bridge this insulation
under the following conditions:
the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by EN
60384-14, which in addition to the Y3 testing, is
tested with an impulse test of 2,5 kV defined in EN
60950-1:2006, 6.2.2.1;
the additional testing shall be performed on
all the test specimens as described in
EN 60384-14:
the impulse test of 2,5 kV is to be performed
before the endurance
test in EN 60384-14, in
the sequence of tests as described in EN 6038414.
6.1.2.2
In Finland, Norway and Sweden, the exclusions
are applicable for PERMANENTLY CONNECTED
EQUIPMENT, PLUGGABLE EQUIPMENT TYPE B
and equipment intended to be used in a
RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a
telecommunication centre, and which has provision
for a permanently connected PROTECTIVE
EARTHING CONDUCTOR and is provided with
instructions for the installation of that conductor by
a SERVICE PERSON.
N/A
7.2
In Finland, Norway and Sweden, for requirements No cable distribution system.
see 6.1.2.1 and 6.1.2.2 of this annex.
N/A
The term TELECOMMUNICATION NETWORK in
6.1.2 being replaced by the term CABLE
DISTRIBUTION SYSTEM.
7.3
In Norway and Sweden, for requirements see
1.2.13.14 and 1.7.2.1 of this annex.
N/A
7.3
In Norway, for installation conditions see EN
60728-11:2005.
N/A
IEC 60950-1, GROUP DIFFERENCES (CENELEC common modifications EN)
Page 85 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
CANADA NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to ................ : CAN/CSA-C22.2 NO. 60950-1A-07
Attachment Form No. ..................... :
Attachment Originator ................... :
Master Attachment ......................... :
CA_ND_IEC60950_1C
TÜV SÜD Product Service GmbH
Date (2012-08)
Copyright © 2012 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
P
Special national conditions
1.1.1
All equipment is to be designed to allow installation in
accordance with the National Electrical Code (NEC),
ANSI/NFPA 70, the Canadian Electrical Code (CEC),
Part I, CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2.
Unit was evaluated
according to IEC 60950-1.
The requirements have to be
checked during National
approval.
Also, unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
P
1.4.14
For Pluggable Equipment Type A, the protection in the
installation is assumed to be 20A.
Considered.
1.5.5
For lengths exceeding 3.05 m, external interconnecting
flexible cord and cable assemblies are required to be a
suitable cable type (e.g. DP, CL2) specified in the
CEC/NEC.
Less than 3.0 m
For lengths 3.05 m or less, external interconnecting
flexible cord and cable assemblies that are not types
specified in the CEC are required to have special
construction features and identification markings.
Interconnecting cord located
in limited power source and
rated VW-1 or better.
Equipment for use on a.c. mains supply systems with a
neutral and more than one phase conductor (e.g.
120/240 V, 3-wire) require a special marking format for
electrical ratings.
Single phase conductor.
1.7.1
A voltage rating that exceeds an attachment plug cap
rating is only permitted if it does not exceed the extreme
operating conditions in Table 2 of CAN/CSA C22.2 No.
235, and
- if it is part of a range that extends into the Table 2
"Normal Operating Conditions."
Canadian differences
P
P
N/A
P
N/A
Page 86 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
A voltage rating is not be lower than the specified
"Normal Operating Conditions," unless it is part of a
range that extends into the "Normal Operating
Conditions."
1.7.7
2.5
2.6.3.3
2.7.1
Wiring terminals intended to supply Class 2 outputs in
accordance with CEC Part 1 or NEC shall be marked
with the voltage rating and “Class 2” or equivalent.
No such terminals.
N/A
- Marking is located adjacent to the terminals.
N/A
- Marking is visible during wiring.
Fuse providing Class 2, Limited Power Source, or TNV
current limiting is not operator-accessible unless it is not
interchangeable.
Modify first column on Table 2D to “Smaller of the
RATED CURRENT of the equipment or the
PROTECTIVE CURRENT RATING of the circuit under
consideration.”
N/A
PTC to provide LPS not
operator-accessible.
P
N/A
Suitable NEC/CEC branch circuit protection rated at the
maximum circuit rating is provided for all standard supply
outlets and receptacles (such as supplied in power
distribution units) if the supply branch circuit protection is
not suitable.
No standard supply outlets.
N/A
Power distribution transformers distributing power at 100
volts or more, and rated 10 kVA or more, provided with
special transformer overcurrent protection.
No such transformers.
N/A
Wiring methods (terminals, leads, etc.) used for the
connection of the equipment to the mains is in
accordance with the NEC/CEC.
Attachment plugs of power supply cords are rated not
less than 125 percent of the rated current of the
equipment.
Overall acceptance has to
be evaluated during the
National approval process.
Power supply cord not
provided.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power
system, and having one pole of the DC mains input
terminal connected to the main protective earthing
terminal in the equipment comply with special earthing,
wiring, marking and installation instruction
requirements.
Not connected to DC mains.
N/A
3.2.3
Permanent connection of equipment to the mains
supply by a power supply cord is not permitted, except
for certain equipment, such as ATMs.
Not permanent connection.
N/A
3.2.5
Power supply cords are required to be no longer than
4.5 m in length.
Power supply cord not
provided.
N/A
3.2
3.2.1
Minimum cord length is required to be 1.5 m, with
certain constructions such as external power supplies
allowed to consider both input and output cord lengths
into the requirement.
Canadian differences
N/A
N/A
Page 87 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Flexible power supply cords are compatible with Article
400 of the NEC, and Tables 11 and 12 of the CEC.
Verdict
N/A
3.2.9
Permanently connected equipment have a suitable
wiring compartment and wire bending space.
Appliance inlet used.
N/A
3.3
Wiring terminals and associated spacings for field wiring Appliance inlet used.
connections comply with CSA C22.2 No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm2 ).
N/A
3.3.4
Terminals for permanent wiring, including protective
earthing terminals, are suitable for Canadian/US wire
gauge sizes, are
N/A
- rated 125 percent of the equipment rating, and
N/A
- are specially marked when specified (1.7.7).
N/A
3.3.5
Revise first column of Table 3E to “Smaller of the
RATED CURRENT of the equipment or the
PROTECTIVE CURRENT RATING of the circuit under
consideration.”
Revised.
3.4.2
Motor control devices are provided for cord-connected
equipment with a motor if the equipment is rated more
than 12 A,
No such motors.
P
N/A
- or if the motor has a nominal voltage rating greater
than 120 V,
N/A
- or is rated more than 1/3 hp (locked rotor current over
43 A).
N/A
3.4.8
Vertically-mounted disconnect switches and circuit
breakers have the "on" position indicated by the handle
in the up position.
3.4.11
For computer room applications, equipment with battery No such battery.
systems capable of supplying 750 VA for five minutes
have a battery disconnect means that may be
connected to the computer room remote power-off
circuit.
N/A
4.3.12
The maximum quantity of flammable liquid stored in
equipment complyies with NFPA 30.
N/A
4.3.13.5
Equipment with lasers meet the Canadian Radiation
Emitting Devices Act, REDR C1370 and/or Code of
Federal Regulations 21 CFR 1040, as applicable.
4.7
For computer room applications, automated information No such systems.
storage systems with combustible media greater than
0.76 m3 (27 cu ft) have a provision for connection of
either automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
Canadian differences
No such switches or
breakers.
No flammable liquid.
N/A
P
N/A
Page 88 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
4.7.3.1
No such enclosures.
For computer room applications, enclosures with
combustible material measuring greater than 0.9 m2 (10
sq ft) or a single dimension greater than 1.8 m (6 ft)
have a flame spread rating of 50 or less.
N/A
For other applications, enclosures with the same
dimensions require a flame spread rating of 200 or less.
N/A
Annex H
Equipment that produces ionizing radiation comply with
the Canadian Radiation Emitting Devices Act, REDR
C1370 and/or Code of Federal Regulations, 21 CFR
1020, as applicable.
Result - Remark
No ionizing radiation source.
Verdict
N/A
P
Other National Differences
1.5.1
Some components and materials associated with the
risk of fire, electric shock, or personal injury have
component or material ratings in accordance with the
applicable national (Canadian and/or U.S.) component
or material standard requirements.
(see appended table 1.5.1)
P
1.6.1.2
A circuit for connection to the DC Mains Supply is
classified as either a SELV Circuit, TNV-2 Circuit or
Hazardous Voltage Circuit depending on the maximum
operating voltage of the supply.
No connection to DC mains.
N/A
This maximum operating voltage shall include
consideration of the battery charging “float voltage”
associated with the intended supply system, regardless
of the marked power rating of the equipment.
N/A
2.3.1
For TNV-2 and TNV-3 circuits with other than ringing
No TNV circuits.
signals and with voltages exceeding 42.4 Vpeak or 60
Vd.c., the maximum acceptable current through a 2000
ohm resistor (or greater) connected across the voltage
source with other loads disconnected is 7.1 mA peak or
30 mA d.c. under normal operating conditions.
N/A
2.3.2.1
In the event of a single fault between TNV and SELV
circuits, the limits of 2.2.3 apply to SELV Circuits and
accessible conductive parts.
N/A
2.6.3.4
Protective bonding conductors of non-standard
protective bonding constructions (e.g., printed circuit
traces) may be subjected to the additional limited short
circuit test conditions specified.
No such constructions.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of 160
mm or more reduce the risk of injury due to the
implosion of the CRT.
No CRTs.
N/A
4.3.2
Equipment with handles complies with special loading
tests.
No safety related handles.
N/A
5.1.8.3
Equipment intended to receive telecommunication
ringing signals is required to comply with a special
touch current measurement tests.
No TNV circuits
N/A
Canadian differences
Page 89 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
5.3.7
Internal (e.g., card cage) SELV circuit connectors and
printed wiring board connectors that are accessible to
the operator and that deliver power are overloaded.
Complied and tested by
approved power supply.
P
During abnormal operating testing, if a circuit is
interrupted by the opening of a component, the test
shall be repeated twice (three tests total) using new
components as necessary
Considered.
P
6.4
Equipment intended for connection to
telecommunication network outside plant cable is
protected against overvoltage from power line crosses
in accordance with 6.4 and Annex NAC.
No TNV circuits.
N/A
Annex EE
Articulated accessibility probe (Fig EE.3) is used for
assessing accessibility to document/media shredders
instead of the Figure 2A test finger.
Not shredders.
N/A
No TNV circuits.
N/A
Equipment connected to a telecommunication and cable No TNV circuits.
distribution networks and supplied with an earphone
intended to be held against, or in the ear comply with
special acoustic pressure requirements.
N/A
Annex M.2 Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
Annex
NAD
Canadian differences
Verdict
Page 90 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
ATTACHMENT TO TEST REPORT IEC 60950-1
US NATIONAL DIFFERENCES
Information technology equipment – Safety –
Part 1: General requirements
Differences according to ................ : UL 60950-1-07
Attachment Form No. ..................... : US_ND_IEC60950_1C
Attachment Originator ................... : TÜV SÜD Product Service GmbH
Master Attachment ......................... : Date (2012-08)
Copyright © 2012 IEC System for Conformity Testing and Certification of Electrical Equipment
(IECEE), Geneva, Switzerland. All rights reserved.
P
Special national conditions
1.1.1
All equipment is to be designed to allow installation in
accordance with the National Electrical Code (NEC),
ANSI/NFPA 70, the Canadian Electrical Code (CEC),
Part I, CAN/CSA C22.1, and when applicable, the
National Electrical Safety Code, IEEE C2.
Unit was evaluated
according to IEC 60950-1.
The requirements have to be
checked during National
approval.
Also, unless marked or otherwise identified, installation
is allowed per the Standard for the Protection of
Electronic Computer/Data-Processing Equipment,
ANSI/NFPA 75.
P
1.4.14
For Pluggable Equipment Type A, the protection in the
installation is assumed to be 20A.
Considered.
1.5.5
For lengths exceeding 3.05 m, external interconnecting
flexible cord and cable assemblies are required to be a
suitable cable type (e.g. DP, CL2) specified in the
CEC/NEC.
Less than 3.0 m
For lengths 3.05 m or less, external interconnecting
flexible cord and cable assemblies that are not types
specified in the CEC are required to have special
construction features and identification markings.
Interconnecting cord located
in limited power source and
rated VW-1 or better.
Equipment for use on a.c. mains supply systems with a
neutral and more than one phase conductor (e.g.
120/240 V, 3-wire) require a special marking format for
electrical ratings.
Single phase conductor.
1.7.1
A voltage rating that exceeds an attachment plug cap
rating is only permitted if it does not exceed the extreme
operating conditions in Table 2 of CAN/CSA C22.2 No.
235, and
- if it is part of a range that extends into the Table 2
"Normal Operating Conditions."
US National Differences
P
P
N/A
P
N/A
Page 91 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
A voltage rating is not be lower than the specified
"Normal Operating Conditions," unless it is part of a
range that extends into the "Normal Operating
Conditions."
1.7.7
2.5
2.6.3.3
2.7.1
Wiring terminals intended to supply Class 2 outputs in
accordance with CEC Part 1 or NEC shall be marked
with the voltage rating and “Class 2” or equivalent.
No such terminals.
N/A
- Marking is located adjacent to the terminals.
N/A
- Marking is visible during wiring.
Fuse providing Class 2, Limited Power Source, or TNV
current limiting is not operator-accessible unless it is not
interchangeable.
Modify first column on Table 2D to “Smaller of the
RATED CURRENT of the equipment or the
PROTECTIVE CURRENT RATING of the circuit under
consideration.”
N/A
PTC to provide LPS not
operator-accessible.
P
N/A
Suitable NEC/CEC branch circuit protection rated at the
maximum circuit rating is provided for all standard supply
outlets and receptacles (such as supplied in power
distribution units) if the supply branch circuit protection is
not suitable.
No standard supply outlets.
N/A
Power distribution transformers distributing power at 100
volts or more, and rated 10 kVA or more, provided with
special transformer overcurrent protection.
No such transformers.
N/A
Wiring methods (terminals, leads, etc.) used for the
connection of the equipment to the mains is in
accordance with the NEC/CEC.
Attachment plugs of power supply cords are rated not
less than 125 percent of the rated current of the
equipment.
Overall acceptance has to
be evaluated during the
National approval process.
Power supply cord not
provided.
N/A
3.2.1.2
Equipment connected to a centralized d.c. power
system, and having one pole of the DC mains input
terminal connected to the main protective earthing
terminal in the equipment comply with special earthing,
wiring, marking and installation instruction
requirements.
Not connected to DC mains.
N/A
3.2.3
Permanent connection of equipment to the mains
supply by a power supply cord is not permitted, except
for certain equipment, such as ATMs.
Not permanent connection.
N/A
3.2.5
Power supply cords are required to be no longer than
4.5 m in length.
Power supply cord not
provided.
N/A
3.2
3.2.1
Minimum cord length is required to be 1.5 m, with
certain constructions such as external power supplies
allowed to consider both input and output cord lengths
into the requirement.
US National Differences
N/A
N/A
Page 92 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Flexible power supply cords are compatible with Article
400 of the NEC, and Tables 11 and 12 of the CEC.
Verdict
N/A
3.2.9
Permanently connected equipment have a suitable
wiring compartment and wire bending space.
Appliance inlet used.
N/A
3.3
Wiring terminals and associated spacings for field wiring Appliance inlet used.
connections comply with CSA C22.2 No. 0.
N/A
3.3.3
Wire binding screws are not permitted to attach
conductors larger than 10 AWG (5.3 mm2 ).
N/A
3.3.4
Terminals for permanent wiring, including protective
earthing terminals, are suitable for Canadian/US wire
gauge sizes, are
N/A
- rated 125 percent of the equipment rating, and
N/A
- are specially marked when specified (1.7.7).
N/A
3.3.5
Revise first column of Table 3E to “Smaller of the
RATED CURRENT of the equipment or the
PROTECTIVE CURRENT RATING of the circuit under
consideration.”
Revised.
3.4.2
Motor control devices are provided for cord-connected
equipment with a motor if the equipment is rated more
than 12 A,
No such motors.
P
N/A
- or if the motor has a nominal voltage rating greater
than 120 V,
N/A
- or is rated more than 1/3 hp (locked rotor current over
43 A).
N/A
3.4.8
Vertically-mounted disconnect switches and circuit
breakers have the "on" position indicated by the handle
in the up position.
3.4.11
For computer room applications, equipment with battery No such battery.
systems capable of supplying 750 VA for five minutes
have a battery disconnect means that may be
connected to the computer room remote power-off
circuit.
N/A
4.3.12
The maximum quantity of flammable liquid stored in
equipment complyies with NFPA 30.
N/A
4.3.13.5
Equipment with lasers meet the Canadian Radiation
Emitting Devices Act, REDR C1370 and/or Code of
Federal Regulations 21 CFR 1040, as applicable.
4.7
For computer room applications, automated information No such systems.
storage systems with combustible media greater than
0.76 m3 (27 cu ft) have a provision for connection of
either automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
US National Differences
No such switches or
breakers.
No flammable liquid.
N/A
P
N/A
Page 93 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
4.7.3.1
For computer room applications, enclosures with
No such enclosures.
combustible material measuring greater than 0.9 m2 (10
sq ft) or a single dimension greater than 1.8 m (6 ft)
have a flame spread rating of 50 or less.
N/A
For other applications, enclosures with the same
dimensions require a flame spread rating of 200 or less.
N/A
Annex H
Equipment that produces ionizing radiation comply with
the Canadian Radiation Emitting Devices Act, REDR
C1370 and/or Code of Federal Regulations, 21 CFR
1020, as applicable.
Result - Remark
No ionizing radiation source.
Verdict
N/A
P
Other National Differences
1.5.1
Some components and materials associated with the
risk of fire, electric shock, or personal injury have
component or material ratings in accordance with the
applicable national (Canadian and/or U.S.) component
or material standard requirements.
(see appended table 1.5.1)
1.6.1.2
A circuit for connection to the DC Mains Supply is
classified as either a SELV Circuit, TNV-2 Circuit or
Hazardous Voltage Circuit depending on the maximum
operating voltage of the supply.
No connnection to DC
mains.
P
N/A
This maximum operating voltage shall include
consideration of the battery charging “float voltage”
associated with the intended supply system, regardless
of the marked power rating of the equipment.
N/A
2.3.1
For TNV-2 and TNV-3 circuits with other than ringing
No TNV circuits.
signals and with voltages exceeding 42.4 Vpeak or 60
Vd.c., the maximum acceptable current through a 2000
ohm resistor (or greater) connected across the voltage
source with other loads disconnected is 7.1 mA peak or
30 mA d.c. under normal operating conditions.
N/A
2.3.2.1
In the event of a single fault between TNV and SELV
circuits, the limits of 2.2.3 apply to SELV Circuits and
accessible conductive parts.
N/A
2.6.3.4
Protective bonding conductors of non-standard
protective bonding constructions (e.g., printed circuit
traces) may be subjected to the additional limited short
circuit test conditions specified.
No such constructions.
N/A
4.2.8.1
Enclosures around CRTs with a face diameter of 160
mm or more reduce the risk of injury due to the
implosion of the CRT.
No CRTs.
N/A
4.3.2
Equipment with handles complies with special loading
tests.
No safety related handles.
N/A
US National Differences
Page 94 of 94
Report No. 18005046 001
IEC 60950_1C ATTACHMENT
Clause
Requirement + Test
Result - Remark
Verdict
5.1.8.3
Equipment intended to receive telecommunication
ringing signals is required to comply with a special
touch current measurement tests.
No TNV circuits
N/A
5.3.7
Internal (e.g., card cage) SELV circuit connectors and
printed wiring board connectors that are accessible to
the operator and that deliver power are overloaded.
Complied and tested by
approved power supply.
P
During abnormal operating testing, if a circuit is
interrupted by the opening of a component, the test
shall be repeated twice (three tests total) using new
components as necessary
Considered.
P
6.4
Equipment intended for connection to
telecommunication network outside plant cable is
protected against overvoltage from power line crosses
in accordance with 6.4 and Annex NAC.
No TNV circuits.
N/A
Annex EE
Articulated accessibility probe (Fig EE.3) is used for
assessing accessibility to document/media shredders
instead of the Figure 2A test finger.
Not shredders.
N/A
No TNV circuits.
N/A
Equipment connected to a telecommunication and cable No TNV circuits.
distribution networks and supplied with an earphone
intended to be held against, or in the ear comply with
special acoustic pressure requirements.
N/A
Annex M.2 Continuous ringing signals up to 16 mA only are
permitted if the equipment is subjected to special
installation and performance restrictions.
Annex
NAD
US National Differences
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement