Model MJ-9000V

Model MJ-9000VG

(Greystoke Model)

Installation Manual

Website: http://www.MajesticAppliances.com

Check this website under Models for the most up-to-date manual. In all situations, the most current manual goverens in questions of use and warranty

Welcome...

Congratulations. Welcome to the growing family of Majestic™ Appliance owners. By choosing a Majestic Appliances model as your laundry appliance you not only found the best in reliable technology, but above all you have found a faithful and untiring convenience appliance.

Your machine is strong, reliable and long lasting. All those qualities which have made the Majestic™ trademark famous the world over.

Above all, Majestic products are easy to use. Read this owner’s manual carefully since it contains all the instruction for safe installation, use and maintenance. Remember to keep your owner’s manual in a safe place so that you can refer to it whenever you need to.

For additional information and contact with the our staff, we invite you to visit our web site.

http://www.MajesticAppliances.com

(Majestic Appliances has made it easy to register your appliance online. Just go to our website and click on “Online Registration”.

Registering your product is essential to receive warranty service.)

We offer a wide range of appliance products, some of which might suit your needs. We also offer our revolutionary MajesticAppliances.TV web option, where you can view orientation movies on the web as well as comments from other users and frequently asked questions. Welcome to our Family!

For Your Records

Thank you for purchasing our Majestic Appliances Product.

This manual will guide you in getting the most productive use of your appliance purchase.

Remember to record you Model and Serial Number. They are on a label on the back of the machine or inside the door.

Model Number

Serial Number

Date of Purchase

Staple your receipt to your manual. YOU WILL NEED IT TO OBTAIN WARRANTY SERVICE!

Installing/Removing

Getting things ready to install your appliance

Unpacking, Inspecting, Electricity, Closets/Alcoves,

Plumbing, Venting

Unpacking

•

Check the packing box for external damage. It is your responsibility to register any damage with the freight company delivering the product.

•

Remove the strapping, then slide the cardboard surround off the machine. Remove the foam protecting material and the plastic bag.

•

Write down the serial number from the box or the back of the machine.

•

Destroy the carton, plastic bags and foam parts after appliance has been unpacked.

•

Children should never be left alone or unattended in the area where appliances being unpacked.

OWNER RESPONSIBLE

FOR DAMAGE RESULTING

FROM TIPPING MACHINE

AFTER REMOVING

SHIPPING BOLTS. AVOID

• If you have any doubts, do not use the appliance and call on a qualified

TIPPING MACHINE

FORWARD AFTER

SHIPPING BOLTS ARE technician.

REMOVING THE FOAM DRUM SUPPORT

REMOVED

REPLACING THE METAL BOTTOM PAN.

EXTRA CARE HAS BEEN TAKEN TO PREVENT SHIPPING

DAMAGE. MAJESTIC IS THE ONLY COMPANY WHO SHIPS THIER

APPLIANCES WITH A DRUM SUPPORT TO REDUCE TRANSIT

DAMAGE. THE FOAM DRUM SUPPORT MUST BE REMOVED. HERE

WE DEMONSTRATE HOW TO ACCOMPLISH THIS.

SHIPPING

BOLTS MUST

REMAIN IN

MACHINE

DURING THIS

PROCESS!

Carefully tip the unit from front to back making sure it can’t tip all the way over.

Remove the foam drum support.

With the unit tipped back, loosen the leveling legs a few turns.

Tip the unit the other direction from the back and remove the leveling legs totally

Slide the bottom pan so Replace the rear leveling that the front slots in the legs and tighten them pan fit over the feet of down securely.

the leveling legs.

Page 1

Go to the front of the machine and retighten the leveling legs and you are done.

REMOVING THE FOAM DRUM SUPPORT

REPLACING THE METAL BOTTOM PAN.

WARNING!!! IN ORDER TO REMOVE THE

FOAM DRUM SUPPORT AND REPLACE THE

METAL BOTTOM PAN, THE BOTTOM OF THE

MACHINE MUST BE ACCESSED. SHIPPING

BOLTS MUST REMAIN IN THE APPLIANCE

WHILE ACCOMPLISHING THIS STEP IN THE

PREPARATION PHASE OF THE INSTALLATION.

Inspecting WHEN TO REMOVE SHIPPING BOLTS!

WARNING!!! TIPPING THE MACHINE TO POSITION IT FOR USE

MUST BE DONE WITH THE SHIPPING BOLTS STILL IN THE

MACHINE!

TIPPING THE MACHINE WITHOUT SHIPPING BOLTS, CAN CAUSE

THE INNER DRUM TO IMPACT OTHER INTERNAL PARTS, THUS

DAMAGING THEM. POSITION THE MACHINE AS CLOSE AS

POSSIBLE TO IT’S FINAL POSITION AND THEN REMOVE SHIPPING

BOLTS.

ATTENTION:

DO NOT TAKE

OUT SHIPPING

√

INSPECT CONTENTS

[ ] Owners Manual

Brass Pressure Regulators

[ ] (Must be installed on hot and cold water inlet. Failure to do so can damage the internal components and cause water damage for which the installer/owner will be re- sponsible!)

[ ] Warranty Registration Card

[ ] Majestic Literature

[ ] Hoses have washers in

both ends.

BOLTS UNTIL

MACHINE IS

POSITIONED

WITHIN A FEW

INCHES OF ITS

FINAL INSTALL-

TION POINT. TIP-

PING THE UNIT

OR MOVING IT

WITHOUT SHIP-

PING BOLTS

WILL VOID WAR-

RANTY.

Brass Pressure

Regulators installed on back of appliance.

Page 2

Installing/Removing

Getting things ready to install your appliance (continued)

Electricity

Make sure that the voltage and frequency available correspond with the values stated on the data plate located at the back of the machine and that the electric system is dimensioned to withstand the maximum current shown on the data plate. If the socket the machine is connected to does not correspond with the plug, replace the plug with a suitable one and avoid using adapters or shunts since they could cause over heating and burn out.

Grounding

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having and equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

WARNING- Improper connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualified or service representative or personnel if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance: if it will not fit the outlet, have a proper outlet installed by a qualified electrician.

Electrical Specifications:

Voltage/Amperage - 115V, 12 Amp, 60 Hz 3 Prong plug attached to the appliance in the factory

Circuit/Protection - 3 wires single phase, 120V, 60 Hz, AC separate 15 amp circuit or greater.

Recessed, Closet and Alcove Installations

This appliance may be installed in a recessed area, closet or alcove. All measurements are in inches.

• If the appliance is to be installed in a closet with zero clearance on the side of the appliance, a total of 12 square inches of free air space movement to the back of the unit must be allowed into the closet.

• If a door is to be installed that potentially encloses the unit while running, the door must allow for a minimum of 20 square inches of free air movement. There must also be a 1” space from the front of the unit to the closed door and 1” from the back of the unit to the wall. Additional spacing should be considered for easy installation, servicing, removal and compliance with applicable local, state and federal codes.

• The floor must be able to support at least 280 lbs and a surface that is solid and level. If machine is to be placed in cabinet, up off the floor, it may be necessry to secure the drum with a tether to prevent excessive drum movement. Plese call Majestic Appliances for more information.

• Installations in RV’s or Marine pleasure craft suggest that the machine might best be installed midships in the boat, or over the axles of the RV where movement is at a minimum.

Adequate blocking should prevent extreme movement when installed in an RV or Marine pleasure craft.

If the appliance is to be installed in a closet, the installation must be completed by a qualified person or service representative.

Additional clearances for floor, wall or door moldings may be required.

Page 3

Installing/Removing

Getting things ready to install your appliance (continued)

Plumbing - Water, Drains

WATER CONNECTION

1. This appliance can be used with either hot/cold or cold/cold connections.

2. The hoses supplied have either a straight end or an elbow end. The elbow end is meant to connect to the washer. Be sure to connect the hot hose to the hot side of the appliance itself, the cold side to the cold connection.

(See picture) The straight end to the 3/4” BSP standard hose bib thread.

3. MAKE SURE WASHERS ARE INSTALLED IN EACH END OF THE SUPPLY

HOSES.

4. Ensure that water connections are free from debris or sediment.

6. BRASS PRESSURE REDUCERS MUST BE INSTALLED TO PROTECT

COMPONENTS INSIDE THE APPLIANCE.IMPORTANT ! CHECK THREADS

ON THE MACHINE, THE BRASS PRESSURE REDUCERS AND THE SUPPLY

HOSES TO ENSURE THEY ARE CLEAN. DO NOT USE EXCESSIVE FORCES.

TIGHTEN BY HAND. DO NOT USE POWER TOOLS.

Connection of the drain hose to standpipe

• Outlet end of drain hose (See figure 2) must be at least 20” above bottom of washer. Do NOT block top of standpipe closed with tape or other materials. An air break must be provided at the standpipe to avoid siphoning.

• Connect the drain hose to a standpipe (with internal diameter of at least 3.2 cm or 1 1/4” min. diameter) with a minimum carry away volume of 7 gallons. The top of the standpipe must be 20” minimum from the botton of the appliance. Place drain hose for drainage into a sink tub or standpipe, ensuring that there are no kinks or bends. The free end must be at a height of 80 cm (31 1/2”) from the floor, the hose must be fixed in the appropriate hook on the upper part of the back panel (fig.4)

DO NOT INSERT THE END IF THE DRAIN HOSE MORE THAN 6” INTO

THE STANDPIPE. INSERTING MORE MAY CAUSE THE APPLIANCES TO

HAVE INSUFFICIENT DRAINAGE.

CORRECT LEVELING OF UNIT IS

ESSENTIAL

It is important for the machine to be perfectly level. The angle of inclination on the work surface must not be more than

2 degrees. For this reason the machine is fitted with adjustable feet used for leveling the machine before use. In the case of carpeted flooring, remember to check that the ventilation in the support area is not plugged.

Exhaust Duct Installation

• Check that all ducting is lint free. Secure ducting with clamps or metal tape.

• The exhaust duct must end with an approved exhaust vent hood with swing out dampers or appropriate louvers.

• Flex or rigid metalic ducting is recommended.

• Exhaust duct should be short and straight and slope downwards and away from the appliance. Long exhaust duct runs can increase drying time and collect lint.

IMPORTANT! THE EXHAUST DUCT SHOULD NOT BE INSERTED INTO A

CHIMNEY WALL, CEILING OR CONCEALED SPACE OR STRUCTURE.