7585  TOUR-TECH™ CRUISE MOUNTS, SHORT ARM WITH TRIDENT DUALLY ISO-PEGS

7585  TOUR-TECH™ CRUISE MOUNTS, SHORT ARM WITH TRIDENT DUALLY ISO-PEGS
TOUR-TECH™ CRUISE MOUNTS, SHORT ARM WITH TRIDENT DUALLY ISO-PEGS
7585 Thank You For Choosing Küryakyn!
Protect yourself and others from potential injury and property damage or loss. Pay close attention to all instructions, warnings, cautions, and notices
regarding the installation, use, and care of this product.
THIS INDICATION ALERTS YOU TO THE FACT THAT IGNORING THE CONTENTS DESCRIBED HEREIN CAN
RESULT IN POTENTIAL DEATH OR SERIOUS INJURY.
This indication alerts you to the fact that ignoring the contents described herein may negatively affect product
performance and functionality or damage the product itself or the product to which it is being attached.
ENSURE THAT THE FOLLOWING PARTS HAVE BEEN INCLUDED IN THE KIT:
2
2
1
1
Tour-Tech™ Cruise Mounts, Short Arm with Trident Dually ISO-Pegs
#10-24 Set Screws
Anti-Seize Packet
Installation Instructions
YOU WILL ALSO NEED:
Set of Hex Wrenches
These installation instructions contain important information. Ensure that the end user receives this copy and is
aware of its importance for future use.
STEP 1
Read and understand all steps in the instructions before starting the installation. Park the motorcycle on a hard, level surface and turn
IGN OFF. Allow the engine and exhaust system to cool. Remove the main fuse.
THE END USER’S SAFETY DEPENDS UPON PROPER INSTALLATION OF THIS PRODUCT. IF A STEP IN
THESE INSTRUCTIONS IS NOT WITHIN YOUR CAPABILITIES OR YOU DO NOT HAVE THE CORRECT
TOOLS, HAVE YOUR DEALER PERFORM THE PROCEDURE. IMPROPER INSTALLATION OF THIS
PRODUCT COULD RESULT IN DEATH OR SERIOUS INJURY.
ACCIDENTAL VEHICLE START-UP COULD CAUSE DEATH OR SERIOUS INJURY, REMOVE THE MAIN
FUSE BEFORE PROCEEDING.
STEP 2
Determine the desired position of the Tour Tech™ mounts on the engine guard.
STEP 3
Refer to PIC 1. Remove the 1/2”-20 screw from the mount. Note the
splines on the arm and clamp that allow for additional adjustment.
PIC 1
PIN HEAD ON TOP
SPLINES FACE OUT
Determine the mounting location and orientation
of the Tour Tech mounting clamp before fully
tightening the clamp screw. The Tour Tech
mounting clamp may leave marks when tightened.
STEP 4
7585-13MC-0615
Refer to PIC 1. Fold the clamp around the engine guard in the desired location. Ensure the head of the hinge pin is on top. The
splined face of the clamp should face away from the bike.
BRAKE-SIDE (RIGHT) SHOWN
NYLON WASHER
1/2”-20 SCREW
Page 1
STEP 5
Re-install the arm on the clamp. Position the nylon washer between the clamp
halves as shown in PIC 2.
NOTE:
PIC 2
BRAKE-SIDE (RIGHT)
The washer is cosmetic only. When the clamp is tightened, the “ears” of the clamp may not touch the washer.
Anti-Seize aids in the future removal of fasteners. Apply the
included Anti-Seize directly to the treads of all installed
fasteners. Do not use Anti-Seize on fasteners with thread
locking compound applied.
NYLON WASHER
PIC 3
STEP 6
Refer to PIC 3. Position the offset arm to your liking. Install and tighten the 1/2”
screw.
STEP 7
Position the footrest as desired. Tighten the 5/16” screw in the end of the footrest. The male mount will seat itself into the footrest and keep it from rotating.
NOTE:
CLUTCH-SIDE (LEFT)
Ensure that the footrests do not contact other parts
when folded up.
1/2”-20 SCREW
POSITION THE TOUR TECH ARMS AND FOOTRESTS SO
THEY DO NOT INTERFERE WITH THE OPERATION OF
THE FOOT CONTROLS. INTERFERENCE WITH THE
FOOT CONTROLS MAY CAUSE LOSS OF CONTROL RESULTING IN SERIOUS INJURY OR DEATH.
UNDERSIDE OF PEG SHOWN
ENSURE THAT THERE IS PROPER GROUND CLEARANCE FOR
CORNERING. LOSS OF CONTROL OF THE MOTORCYCLE AND
SERIOUS INJURY MAY OCCUR IF THE FOOTREST/ARM IS NOT
POSITIONED PROPERLY. REPOSITION THE TOUR TECH™
MOUNT IF NECESSARY SO THAT THERE IS ADEQUATE CORNERING CLEARANCE.
DO NOT USE THIS SET SCREW TO ADJUST ANGLE
STEP 8
Refer to PIC 4. Install the included set screws in the lower holes on the Tour Tech™ arms. Turn the set screws in or out to adjust the
angle of the footrest.
PIC 4
STEP 10
Periodically check the tightness of all fasteners.
INSTALL SET SCREW IN LOWER HOLE; ADJUST
FOOTREST ANGLE WITH SET SCREW
Page 2
BEFORE RIDING, ENSURE THAT THE INSTALLATION OF THIS PRODUCT DOES NOT INTERFERE WITH
THE PROPER OPERATION OF THE MOTORCYCLE.
It is the end user’s responsibility to ensure that all fasteners (including pre-assembled) are tightened before
operation of the motorcycle. Kuryakyn will not provide warranty coverage on products or components lost
or damaged due to improper installation or lack of maintenance. Periodic inspection and maintenance are
required on all fasteners.
Page 3
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement