ZAPI H3D 800A, H3D 1000A DC motor controller Operating handbook
H3D 800A and H3D 1000A are DC motor controllers, designed for use in industrial applications. The devices offer regenerative traction control, standard traction control, 5-speed lifting pump control, and 4-speed lifting pump control with power steering contactor handling. These versatile controllers provide advanced features such as optimum sensitivity to low speeds, self-diagnostics, configuration by a console or mini-console, and parameter modification by a console.
Advertisement
Advertisement
COSTRUZIONE APPARECCHIATURE ELETTRONICHE - OLEODINAMICHE - INDUSTRIALI
42028 - POVIGLIO - (R.E.) - Via Parma, 59 - ITALIA
Tel. (0522) 960050 (r.a.) - Tlx. 530021 AINDRE I - Fax (0522) 960259
H3D 800A / H3D 1000A
OPERATING HANDBOOK AND
FUNCTION DESCRIPTION
INDEX
Page
Legend .............................................................................................................. 3
1 General characteristics ................................................................................. 4
1.1
Technical specification .......................................................................... 4
1.2
Control unit ............................................................................................ 4
1.2a Microswitches ................................................................................ 4
1.2b Potentiometer ................................................................................ 4
1.3
Protection features ................................................................................ 6
1.4
Performance features ............................................................................ 6
1.5
Thermal considerations ......................................................................... 7
1.6
General notes and precautions ...................................................... 7
1.7
Main contactor and safety switch ........................................................... 8
1.8
Susceptibility and electromagnetic emission ................................. 8
2 Installation ...................................................................................................... 9
2.1
Connection cables ................................................................................ 9
2.2
Contactors ............................................................................................. 9
2.3
Fuses .................................................................................................... 9
2.4
H3D connectors................................................................................... 10
2.5
H3D power connectors ........................................................................ 12
2.6
H3D controller mechanical drawing .................................................... 13
3 Parameter modifications ............................................................................. 14
3.1
Modifying parameters using the mini-console ..................................... 14
3.2
Modifying parameters using the digital console................................... 15
3.3
Chopper configuration and connections description ........................... 16
4 H3D chopper diagnosis .............................................................................. 17
5 H3D regenerative traction ........................................................................... 18
5.1
Input connectors description ................................................................ 19
5.2
Programmable functions description (options) .................................... 20
5.3
Adjustment parameter description (menu program) ............................. 21
5.4
Adjustment chart.................................................................................. 22
5.5
Wiring diagram for H3D regenerative .................................................. 23
5.6
Wiring diagram for H3D regenerative with bypass and double................
lever pedal........................................................................................... 24
5.7
Wiring diagram for H3D regenerative with field weakening and ..............
power steering contactor ..................................................................... 25
5.8
Wiring diagram for H3D regenerative with backing ............................. 26
5.9
H3D regenerative with speed check.................................................... 27
5.10 Wiring diagram for H3D regenerative with pick-up .............................. 28
5.10.1 Wiring modification when using a proximity sensor .................. 29
5.10.2 Notes on the gear wheel dimensions........................................ 29
6 H3D standard traction ................................................................................. 30
6.1
Input connectors description ................................................................ 31
6.2
Programmable functions description (options) .................................... 31
6.3
Adjustment parameter description (menu program) ............................. 32
6.4
Adjustment chart.................................................................................. 32
6.5
Wiring diagram for H3D standard with field weakening ....................... 33
Page 1
7 Traction adjustment and diagnosis ........................................................... 34
7.1
Sequence of settings for regenerative/standard traction ...................... 34
7.2
H3D traction diagnosis ........................................................................ 35
7.3
Decoding console displayed alarms ................................................... 36
8 H3D standard lifting..................................................................................... 44
8.1
Input connectors description ................................................................ 45
8.2
Programmable functions description (options) .................................... 45
8.3
H3D standard lifting adjustment parameters description ..................... 46
8.4
Adjustment chart for H3D standard lifting ............................................ 47
8.5
Wiring diagram for H3D standard lifting ............................................... 48
8.6
Wiring diagram for H3D standard lifting with field weakening ............. 49
8.7
Wiring diagram for H3D standard lifting with bypass and main contactors. Power steering command from running contactors (*) ....................................................................................... 50
9 H3D lifting + 3rd motor ............................................................................... 51
9.1
Input connectors description ................................................................ 52
9.2
Programmable functions description (options) .................................... 52
9.3
H3D lifting + 3rd motor adjustment parameters description ................. 53
9.4
Adjustment chart for H3D standard lifting + 3rd motor ......................... 54
9.5
Wiring diagram for connection lifting pump and power steering with bypass and main contactors. Power steering command from running contactors....................................................... 55
10 H3D lifting adjustment and diagnosis ........................................................ 56
10.1 Sequence of setting for lifting .............................................................. 56
10.2 Setting the proportional solenoid valve ............................................... 56
10.3 H3D lifting diagnosis ........................................................................... 57
10.4 Decoding console displayed alarms ................................................... 57
Recommended spare parts for H3D ................................................................. 60
Periodic maintenance to be regularly repeated ............................................... 61
= Information included in marked paragraphs by this symbol is essential for the safety
APPROVAL SIGNATURE
MANAGEMENT EXECUTIVE COMPANY DEPT. SERVICES
ENGINEERING SECTION EXECUTIVE
EXPORT MANAGER
Publication N°: ABDZP0GA
Edition: January 1996
Page 2 H3D
LEGEND
CH
DF
DV
HYD
IN
MA
MCL
MD
AUX
AV
BTA
BTBY
= Auxiliaries (load)
= Forward
= Forward direction contactor coil
= By-pass contactor coil
BTFR
BTI
= Braking contactor coil
= Reverse direction contactor coil
BTIDR = Power Steering contactor coil
BTIND = Weakening contactor coil
= Key
= Braking diode
= Flywheel diode
= Power Steering speed request
= Reverse
= Forward direction microswitch
= Horn microswitch
= Descent microswitch
MEF
MI
= Electric brake microswitch
= Reverse direction microswitch
MS = Lift microswitch
MSED = Seat microswitch
MSIC
MT
MUM
MV
= Safety microswitch
= Tiller microswitch
= Dead man microswitch
= Speed request microswitch
NT = Negative of the contactor
PRPAV = Button for forward direction in backing mode
PRPIN = Button for reverse direction in backing mode
RV = Speed reduction
TA
TBY
TFR
TI
= Forward direction contactor
= By-pass contactor
= Braking contactor
= Reverse direction contactor
TIDR
TIND
VMN
= Power Steering contactor
= Filed weakening contactor
= Negative voltage of the motor
H3D general description Page 3
1 GENERAL CHARACTERISTICS
Voltage:
1.1 TECHNICAL SPECIFICATION
48V/72V/80V/96V/120V/144V (36V-140V) DC
Maximum current: 800A/1000A
Frequency:
Type of motor:
18 kHz
DC Series Wound , 4 cables
Operating ambient temperature: -30 to +40° C
Maximum allowable temperature for chopper body: 85° C
Voltage drop across MOS with I = 300A: 630mV (800A); 410mV (1000A)
Microprocessor logic unit
4 different configurations;
1 regenerative traction control;
2 standard traction control;
3 5 - speed lifting pump control;
4 4 - speed lifting pump control + power steering contactor handling.
1.2 CONTROL UNIT
1.2a Microswitches
Microswitches send a voltage signal when the rapid request for start-up or desired function is made. Microswitches for forward, reverse and rapid inversion (if present) are selected for carrying the current of one contactor.
1.2b Potentiometer
In the 3 - wire configuration, the CPOT (D1) useful input signal goes from 0V to 10V. The resistive value of the potentiometer must be between 500 Ohm and 10 kOhm, as lower values overload the power supply.
You can use also an inductive pedal having voltage 12 V and an uptake of current between 2mA and 30mA.
Relationship between the voltage signal on pin D1 and motor voltage.
Page 4 H3D general description
The procedure for automatic potentiometer signal acquisition is carried out from the console. This makes it possible to adjust the minimum and maximum useful signal in the respective directions.
This function necessary when required to compensate for asymmetry in the mechanical operations that control the potentiometer.
The sequence of procedures is described in the programming manual console.
The acquisition procedure is invalidated by the controller if the difference between the minimum and the maximum value is less than 2 V.
This acquisition procedure allows:
- the use of reversed potentiometer signals i.e. those which reduce from a high initial value to a low final value;
- the use of a normal potentiometer instead of one with central zero.
For correct operation of signal acquisition, it is absolutely necessary that the direction microswitches be activated by the same shaft that moves the potentiometer.
Application examples
- Reversed signal
VACC = accelerator signal voltage on pin D1;
VMOT = percentage on battery voltage on the motor.
- Central zero signal
H3D general description Page 5
1.3 PROTECTION FEATURES
- Battery Inversion:
It is necessary to observe the connections indicated in diagrams in order to prevent damage to the power unit. Protection against polarity reversal can be achieved by an external main contactor. In lifting versions, a main contactor can be connected and controlled by the logic against polarity inversion. The logic is intrinsically protected.
- Connections errors:
All the inputs are protected against connections errors.
The contactors do not accept loads greater than 2 Amp and are in any case protected against overloads and short circuits.
- Thermal Protection:
If the temperature exceeds 80° C the maximum current is reduced in proportion to the thermal increase. The temperature may never exceed 85° C.
- Low Battery charge:
When the battery charge is too low (greater than 75%) the maximum current is reduced by 50%. In the lifting version all functions except power steering (and descent) are disabled.
This feature may be excluded by the Console.
- External Agents:
The controller case has a protection level meeting IP 32.
- Protections against accidental start-up:
A precise sequence of operations is necessary for starting the machine.
If these operations are not carried out correctly the machine will not start.
The request for running must be activated after the key and seat microswitches have operated.
- Protection against uncontrolled movements:
The contactors will not close if:
- the power unit is not operating connecting;
- the accelerator does not go below the minimum value stores increased by 2 Volt, or if there is not the connection to the pin NPOT;
- the logic is not perfectly operational;
- one running microswitch has failed.
1.4 PERFORMANCE FEATURES
- Optimum sensitivity to low speeds.
- Self-diagnosis with indication of the type of fault by an optional LED.
- Configuration by console (traction or lifting).
- Modification of the parameters by console.
- Internal hour-meter with values that can be displayed on the console.
- Memory of the last five alarms with relative hour-meter value and temperature displayed on the console.
Page 6 H3D general description
- Tester by console for real time checking of the main parameters such as inputs, motor voltage, battery, etc..
- Arc less operation of contactors.
- Internal arc suppression of the contactors coils.
- High motor and battery efficiency due to high frequency commutation.
1.5 THERMAL CONSIDERATIONS
- The heat generated must be dissipated. For this reason the location place in the machine must be ventilated and the cooling surfaces adequate.
- The cooling system is dimensioned on the basis of the performance required for the machine. For situations in which ventilation is poor and heat exchange difficult for the materials used, we suggest the use of forced air ventilation.
- The dissipation of power by the module varies depending on the current and the duty cycle.
1.6 GENERAL NOTES AND PRECAUTIONS
- Never combine SCR low frequency choppers with H3D modules, as the filter capacitors contained in the H3D module alter SCR chopper operation, subjecting it to excessive loads.
If you wish to use two or more control units (e.g. lift + traction), they must all be of the high frequency ZAPIMOS family.
- Do not connect the chopper to a battery with a different nominal voltage to that indicated on the chopper identification plate. A higher battery voltage can cause MOS failure. A lower battery voltage prevents the module from operating.
- During battery recharge, the H3D module must be completely disconnected from the battery. In addition to altering the charge read by the battery charger, the module can be damaged by the overload voltages generated by the charger and by the ripple current generated in the capacitors if the battery charger works at low frequency.
- The H3D module must only be supplied with a traction battery. Do not use outputs of converters or power suppliers. For special applications, please consult the nearest
ZAPI service centre.
- Start the machine the first time with the wheels raised, in order to ensure that any connection errors do not create safety risks.
- With the key off, the filter capacitors inside the module may remain charged for several minutes.
For safe operation, we recommend that after disconnecting the battery, short circuit the power positive and negative on the chopper for a few seconds with a resistance of between 10 ohm and 100 ohm min 5 watt.
H3D general description Page 7
1.7 MAIN CONTACTOR AND SAFETY SWITCH
- The connection of eventual interruption systems of the battery must be executed correctly respecting one of the following wiring diagrams.
- With safety switch:
- With switch and general contactor:
- One of the above solutions are necessary to ensure safety should the controller fail when the connection to the battery is opened during the phase of regenerative braking. The controller falls out automatically from braking if the battery voltage is exceeded by 30% of the normal battery voltage.
1.8 SUSCEPTIBILITY AND ELECTROMAGNETIC EMISSION
Susceptibility and electromagnetic emission are considerably influenced by the installation. Take care with the length and the path of the electrical connections and to the braided wires.
Zapi declines any responsibilities for badrunning caused by the circumstances above mentioned, above all if the manufacturer of the machine doesnt carry out the tests required by the regulations in force (EN50081-2).
Page 8 H3D general description
2 INSTALLATION
Install the chopper with the base-plate on a flat metallic surface that is clean and unpainted. Apply a light layer of thermo-conductive grease between the two surfaces to permit better heat dissipation.
Despite the protection provided against external agents, the continuous attack of corrosive substances may cause the connector contacts to oxidise, thus jeopardising good operation. Keep this in mind when choosing the installation position on the vehicle.
Use the special holes on the base-plate for fastening the chopper.
Make sure that the wiring of the cable terminals and connectors is carried out correctly.
Fit suppression filters on the horn, solenoid valves, and contactors not connected to the chopper such as those for activating the pump motor or steering motor, if the latter is not handled by the chopper itself.
2.1 CONNECTION CABLES
For the auxiliary circuits, use cables of 0,5 mm².
For power connections to the motor and to the battery use cables 50mm 2 - 70mm 2 .
For the best controller performance, cables to the battery should be run side by side and be as short as possible.
2.2 CONTACTORS
Choose the type of contactors relative to the maximum operating current of the motor and the specific chopper configuration.
- The current absorbed by the coil must not be greater than 3 amps.
- The coil suppressors are inside the chopper; do not use contactors with arc suppressors.
- For contactors with magnetic suppressors, make sure you respect the polarity indicated on the cap.
- Protect contacts against dust, dirty, external agents which could lead to loss of performance and good operation.
2.3 FUSES
- Use a 10A fuse for auxiliary circuit protection.
- Protect the power unit with a power fuse 1000A.
The value shown is the maximum allowable. For special applications or requirements this value can be reduced.
For safety reasons, we recommend that you use enclosed fuses in order to prevent the spread of fused particles in the event of blowout.
H3D general description Page 9
2.4 H3D CONNECTORS pin
A1
A2 functions
-LED
+LED description
Alarm LED negative: to be connected to the cathode
Alarm LED positive: to be connected to the anode
Output current 12mA, for standard type LED
B1
B2
B3
B4
B5
B6
+15P
+PU*
GND
-PU*
+15P
REF.*
B7 GND
B8 INP
B9 AVP
B10 PT
Page 10
Output +15V for feeding speed sensor
Input positive voltage speed sensor
Negative for feeding speed sensor (0V)
Negative of speed sensor
Auxiliary output +15V
Input for speed set point checked with external potentiometer, voltage range is from 0V to 5V. When you use this input the JP5 jump on the logic must be opened.
Negative of the auxiliary (0V)
Reverse of running input for backing function
Forward of running input for backing function
Output on voltage for common wire of buttons for backing function
H3D general description
C1 PTFR
C2 PT
Positive of braking contactor coil
Positive of weakening and direction contactor coil
C3 NTIND/NTB Negative of weakening or by-pass contactor coil
C4 NTI Negative of Reverse contactor coil
C5 NTFR
C6 NTA
C7 NTGP
C8 PC07
Negative of braking contactor coil
Negative of forward contactor coil
Negative of auxiliary contactor coil
Open collector output for small auxiliary loads (max. 200mA, 24V)
D1 CPOT
D2
D3
NPOT
PPOT
Potentiometer central pin: connected to the potentiometer cursor.
For speed regulation, the useful signal ranges from 0V (minimum speed) to 10V (maximum speed)
Potentiometer negative: (with load circuit)
Potentiometer positive: it is a 12 V output. This output is protected against short circuit. The maximum current load is 30 mA, which is equivalent to a 500 Ohm resistance.
E1
E2
+CH IN
+CH OUT
F1
F2
F3
F4 INPUT
F5
F7
F8 RI (low)
F9 RI (low)
Input to the logic. Connect to the key.
The positive to be sent to the function request microswitches, is taken from this pin. This pin is disconnected from the pin E1 with a diode. Maximum output current 3A.
Pins to which the signals for function request are sent, their meanings varies according to the model selected and pin programming. A detailed description is given in the chapters dedicated to the specific models. Pin F4, if forced to low level, inhibits the effect of pins F8 and F9.
Activates the same request as for pin F4 with a low capacity level
(less than 10V) .
Like F8, but electrically disconnected .
I1
I2
I3
I4
I5
I6
I7
I8
PCLRXD
NCLRXD
PCLTXD
NCLTXD
Serial reception positive.
Serial reception negative.
Serial transmission positive.
Serial transmission negative(regenerative state output for ILBB).
GND
+12
Console supply negative.
Console supply positive.
FUNCTION SELECT Channel for mini-console (speed signal).
UP/DOWN Channel for mini-console (speed ref.).
* = The functions relative to the maximum speed check are activated only if you have programmed the Option SPEED at CHECK mode.
H3D general description Page 11
2.5 H3D POWER CONNECTORS
- B Battery Negative
+SH Current sensor Input
-SH Current sensor output
+B Battery Positive
VMN Is connected to the Power MOSFET drain, and supplies a negative to the motor with variable duty cycle.
Page 12 H3D general description
2.6 H3D CONTROLLER MECHANICAL DRAWING
H3D general description Page 13
3 PARAMETER MODIFICATIONS
Modification of the parameters, in addition to the configuration of the inputs, is made directly by ZAPI on customer specifications, or the customer may make adjustments himself using the programming console or the mini-console, (with the later only certain parameters can be modified). The console can remain connected to the chopper when running and the parameters can also be varied in real time during operation.
To confirm data, press ENTER when requested by the message on the console.
Parameters modified and optimised on one unit can be stored from the console (SAVE) and then reloaded (RESTORED) on another chopper, thus allowing fast and standardised calibration (see console manual for details).
Pay special attention to the polarity of the console connector when it is connected to the chopper.
CONNECTION MUST ONLY BE DONE WITH THE BATTERY DISCONNECTED OR
THE KEY OFF.
3.1 MODIFYING PARAMETERS USING THE MINI-CONSOLE
Parameters that can be modified are:
Traction
1 CREEP SPEED
2 ACCELERATOR DELAY
3 INVERSION BRAKING
4 CUT BACK SPEED 1
5 CUT BACK SPEED 2
0 NOT CONNECTED
Lifting
1 1ST SPEED
2 2ND SPEED
3 3RD SPEED
4 HYDRO SPEED
5 HYDRO COMP.
0 NOT CONNECTED
The adjustments are possible within 10 intermediate levels.
- Connect the mini-console to connector (I) on the chopper.
(the hook-up MUST BE MADE WITH THE KEY OFF).
- Supply the machine by activating the key.
- Position the dial selector on the function to be modified.
The SET-UP button increases the value of the parameter, while SET-DOWN decreases it.
ATTENTION: the variations are made through a count of the number of impulses sent from the buttons; thus for increasing or decreasing more than one point, you need to release and then repress the button.
Keeping the button pressed continuously does not provide continuous variation of the parameters.
- The parameters are modified in real time, making it possible to check the values set immediately.
Modified parameters are automatically stored by the control logic without the need for confirmation before switching off or disconnecting the console.
ATTENTION: the console does not function if connected when the motor is running.
Switch the machine off and on again for activating the console functions.
Page 14 H3D general description
3.2 MODIFYING PARAMETERS USING THE DIGITAL CONSOLE
- Display of the model type, hourmeter and release of the Eprom installed in the controller.
- Model selection:
(SEL MODEL)
REGENER
STANDARD TR.
STANDARD PUMP
PUMP + HYDRO
- Option selection: PIN C3
(SEL OPTION) SPEED bypass / weak free / check
BATTERY free / check
ARB free / check
RELEASE free / braking
HOURS
PIN F1
PIN F4
PIN F2 running / keyon cut b. 3 / quick I seat / handle cut b. 2 / backing
- Battery selection: 24V, 36/40/48V, 60/72/80V, 96V
(SEL BATTERY) fine adjustment
- Auxiliary function: CURRENT GAIN
(AUX FUNCTION) HYDRO CONTACTOR
BIMOTOR CONTACT.
traction pump
- Progr. of parameters: ACCELERATION DELAY
(PROGRAM) INVERS. BRAKING
ACCELERATION DELAY
EV. ACCELER DELAY
RELEASE BRAKINGDECELER. DELAY
PEDAL BRAKINGEV. DECELER DELAY
CUTBACK SP1/SP2/SP3
AUXILIARY TIME
COMPENSATION
BRAKING MODULATION
I MAX.
I MAX.
HYD SPEED COARSE
CREEP SPEED
WEAK DROPOUT
HYD SPEED FINE
HYDRO COMPENS.
CREEP SPEED
CURVE BRAKINGSPEED COARSE 1/2/3/4
CURVE TIME
BACKING TIME
WEAK DROPOUT
HYDRO TIME
SPEED FINE 1/2/3/4
SPEED COMP. 1/2/3/4
MIN VALVE VOLT
MAX VALVE VOLT
H3D general description Page 15
traction
- Tester functions: VMN 30%
(TESTER) VMN 80%
DIRECTION E7/E6
ACCELERATOR
CURRENT
TEMPERATURE
CUTBACK E1/E2/E3
BRAKE E5
SEAT / HANDLE
BATTERY
MOTOR pump
VMN 30%
VMN 80%
DIRECTION E7/E6
ACCELERATOR
CURRENT
TEMPERATURE
SPEED E5/E3/E2
SPEED E1/E4
E4 BATTERY
MOTOR VOLTAGE
VOLTAGE
- Function SAVE: Chopper parameters are stored in the console memory. 10 different memories are available for each chopper model.
- Function RESTORE: Transfer of parameters from console memory to chopper memory.
10 different memories are available for each chopper model.
- ALARM:
- Program VACC:
Display of chopper memory alarms.
Potentiometer stroke parameter.
3.3 CHOPPER CONFIGURATION AND CONNECTIONS DESCRIPTION
The choices made regarding power connections must be communicated to the chopper.
In order to supply this information, you have to connect the chopper to the programming console and access the set model, set options, and set battery menus (see specific configuration descriptions).
- CONFIGURATION OF THE MODEL: SEL MODEL MENU
Allows chopper to operate in one of the 4 possible modes.
1) REGENER. TR = regenerative traction
2) STANDARD TR = standard traction
3) STANDARD PUMP = standard lifting
4) PUMP+HYDRO = lifting with hydrodrive contactor handling
- CONFIGURATION OF OPTIONS: SEL OPTIONS MENU function/pin option meaning
PIN C3
BATTERY
ARB
RELEASE
HOURS
Bypass
Weak
Check
Free
Check
Free
Check
Free
Braking
Running
Key on
Bypass contactor
Weakening contactor.
Speed check activated.
No low battery charge alarm.
Low charge alarm with 50% max. current if less than 10% of charge.
No Anti-rollback.
Anti-rollback.
No regenerative braking at release.
Release braking.
Hour-meter active only when running.
Hour-meter active with key on.
Page 16 H3D general description
PIN F1
PIN F4
PIN F2
Cut b.#3
Quick I
Seat
Handle
Cut b.#2
Backing
F1 = Reduction of speed no.3.
F1 = Rapid inversion input.
F4 = Seat microswitch.
F4 = Handle microswitch.
F2 = Speed reduction no.2.
F2 = Back request with speed relative to cutback speed #2 and timing of backing time parameter.
- SELECTION OF BATTERY VOLTAGE: SEL BATTERY MENU
Makes it possible to set the nominal voltage of the battery for handling the charge status and tester functions.
With ROLL UP/ROLL DOWN buttons it is possible to select battery nominal voltage.
With SET UP/SET DOWN buttons it is possible to make fine adjustments of battery voltage.
- AUXILIARY FUNCTION: allows the aux output of the connector C7 to be active under certain conditions. We can set it in the following way:
1) CURRENT GAIN: Is the logic board standard way of working. The output
AUX C7 is not used. (Jumper setting: 1-3; 2-4)
2) HYDRO CONTACTOR: The output AUX G7 controls the hydrodrive contactor. It should be active during forward, and reverse directions and during release braking. The turning OFF delay is programmable at "AUXILIARY TIME".
(Jumper setting: 1-2; 3-4)
3) BIMOT. CONTACTOR: AUX C7 output is activated when turning from off status to running status and at the beginning of regenerative braking, and it is switched off when PWM is greater than 20%, both statuses.
4 H3D CHOPPER DIAGNOSIS
The microprocessor carries out diagnostic procedures on the main chopper functions, involving 4 basic points.
1) Diagnosis on key start-up which includes: watchdog test, current sensor test, VMN test, contactor pilot test, test for running request present, high accelerator test.
2) Standby diagnosis which includes: watchdog test, VMN test, contactor pilot test, current sensor test.
3) Diagnosis while running which includes: watchdog test, VMN test, current test, contactor test, VMN test in complete conduction, contactor opening-closing test.
4) Continuous diagnosis: temperature check, battery charge check.
Potentiometer connection control.
The diagnostic message is indicated by a certain number of flashes of the LED connected to connector A.
The current alarm message code can be displayed on the programming console.
A description of the alarm codes, possible causes and solutions is given for each configuration in the following sections.
H3D general description Page 17
DESCRIPTION OF CONSOLE PROGRAM VACC FUNCTION
This function looks for and remembers the minimum and maximum potentiometer wiper voltage over the full mechanical range of the pedal. It enables compensation for non symmetry of the mechanical system between directions.
The operation is performed by operating the pedal after entering the PROGRAM VACC function.
Flow Chart showing how to use the PROGRAM VACC function of the Digital Console.
1) Opening Zapi Display.
2) Press ENTER to go into the General Menu.
3) The Display will show :
4) Press ROLL UP or ROLL DOWN button until
PROGRAM VACC appears on the display.
5) Tthe Display will show :
6) Press ENTER to go into the PROGRAM VACC routine.
7) The Display will show the minimum and maximum values of potentiometer wiper output.
Both directions can be shown.
8) Press ENTER to clear these values.
Display will show 0.0.
9) Select Forward Direction, close any interlock switches that may be in the system.
10) Slowly depress the accelerator pedal (or tiller butterfly) to its maximum value. The new minimum and maximum voltages will be displayed on the Console plus an arrow indicating the direction.
5 H3D REGENERATIVE TRACTION
- Input for 3-wire potentiometer (optional 2-wire on request)
- 3 speed reductions
- Input for handle microswitch or seat microswitch (delayed)
- Input for rapid inversion signal
- Input for brake pedal microswitch
- Weakening or bypass contactor handling
- Maximum speed control
- Backing request with associated speed and programmable timing
Page 18 H3D regenerative traction
5.1 INPUT CONNECTORS DESCRIPTION pin function
F1 RV3/QUICK1
F2 RV2/BACKING
F3 RV1
F4 MSED / HANDLE description
Input for 3rd speed reduction request. The request is active when the pin is disconnected. To disconnect link to +CH or adjust to level 9 the corresponding speed. This pin can be programmed as input for rapid inversion signal, the safety is active when pin is opened.
Input for 2nd speed reduction request. The request is active when the pin is opened (low level) and disactivated if the pin is positive (high level) or the speed is programmed to level 9.
If programmed as reverse request (backing), the pin must be free, because the logic drives automatically when you use the inputs B8 and B9, the running is setted with the parameter
CUTBACK 2 and for a time programmable with the parameter
BACKING TIME, when you require this function it is not necessary to active the pin F4 (seat microswitch).
Input for 1st speed reduction request which is active when pin is opened.
The activation of this reduction is combined with an intensity braking and programmable length (CURVE BRAKING) and
(CURVE TIME).
It is possible to eliminate the braking in curve programming curve time as 0.
Input for seat microswitch signal (delayed 2 sec.) if the pin is taken to a high potential the running is active, the delay isn't executed if the pin is programmed as tiller-handle.
F5 MF
F6 MI
F7 MA
Input for brake pedal microswitch when the pin is taken high
(+VB) during a release braking phase the braking current is the one programmed at the parameter "PEDAL BRAKING" plus a value that is proportional to the accelerator signal and to the parameter "BRAKING MODUL".
If the brake is pressed during the usual running the current is reduced by 50% and the speed No. 2 reduction is activated.
Input for backward request signal.
The request is active when the signal is high (+VB)
Input for forward request signal.
The request is active when the signal is high (+VB)
Same as pin F4 but active when signal is low
Same as F8
E8
F9
I6 REF* Input for speed set-point signal with external potentiometer, on this pin it is set up the voltage relative to the maximum speed, the range is 0V - 5V. Open the jumper JP5 for rendering operative this input.
* = The functions relative to the maximum speed check are activated only if you have programmed the Option SPEED at CHECK mode.
H3D regenerative traction Page 19
5.2 PROGRAMMABLE FUNCTIONS DESCRIPTION (OPTIONS) function/pin
1) PIN G3 option description by-pass The contactor connected to connector G3 is handled as a bypass, with activation current = 80%Imax., output current =
90%Imax., activation delay=800 msec.
weak The contactor connected to connector G3 is handled as weakening, with activation current = 50% of Imax. The disabling current is programmable from 10% to 100% of Imax.
(WEAK DROP OUT).
Activation delay=800 msec.
2) SPEED free Speed check not active. The mini-console can be used with this option.
check Speed check active. By the trimmer R22 and or the signal to pin B6 it is set up the maximum speed. When the speed exceeds this value the controller reduces the motor voltage or brakes if the difference persists. The braking goes on until the speed is less than the maximum value set. Sampling is made every 60 sec. Please note that when the speed check option is activated the miniconsole can not be used.
3) BATTERY free No low battery charge alarm check Activates the check that reads the battery voltage in standby.
When the residual charge is less than 10%, the maximum current is halved and the LED blinks continuously.
4) ARB
5) RELEASE free No regenerative braking at release check Braking active at the moment of pedal release with increment of the braking current by means of the brake pedal.
6) HOURS free No anti roll back check Anti-roll back free Hour meter only active when running check Hour meter active when the key is on
7) PIN F1 cut b.#3 It associates the function of n° 3 speed reduction request to the F1 connector quick I It associates the function for rapid inversion to the connector
F1 with the following characteristics: plugging braking with
1.2 x Imax, restart in forward direction with 0.5 x Imax, slower acceleration (to avoid wheel slip). Also the machine will stop if the safety button is released and a forward or backward request is present. The rapid inversion request is accepted only when it is present with the forward request. The function is active when the pin is free or connected to battery negative.
Page 20 H3D regenerative traction
8) PIN F4
9) PIN F2 seat The input of running enable by the seat microswitch is associated to connector F4: A microswitch temporal sequence is requested.
Delay of 2 seconds on deactivation.
The function is active if the pin is connected to the positive handle Like the seat option but without delay cut b.#2 It associates the speed reduction n° 2 to the pin F2.
backing It associates the backing request F2 connector. In this selection please leave the pin free because the connections are inside the logic board.
5.3 ADJUSTMENT PARAMETER DESCRIPTION (MENU PROGRAM)
The parameters can be modified with the controller both in standby and in running.
For storing the modifications in the nonvolatile memory, you must go out from the menu program and confirm the ENTER request.
Regenerative traction parameters:
1) ACCELER DELAY = acceleration time, i.e. the minimum time during which the motor voltage varies from 0V to the maximum.
2) INVERS BRAKING = basic braking current in direction inversion. A value is added to this value based on the accelerator plus a fixed increment every second.
3) RELEASE BRAKING = release braking current.
4) PEDAL BRAKING = release braking current with brake pedal pressed.
5) CUTBACK SP.1 = reduction of speed n° 1 associated to the input F3. The accelerator is reduced.
6) CUTBACK SP.2 = reduction of speed n° 2 associated to the input F2 and to the input F5 if activated on running. It defines the speed to be set up in the BACKING mode.
7) CUTBACK SP.3 = reduction speed n° 3 associated to the input F1.
8) AUXILIARY TIME = auxiliary contactor activating time connecting to the C7 (NTGP) output.
9) COMPENSATION = compensation of the speed (motor voltage) on the basis of the current when the speed reductions are active. It is activated only with the pedal pressed over 80%.
10) BRAKING MODULATION = defines the maximum current in inversion braking with the accelerator pedal pressed. When the accelerator is pressed all the way down in inversion, braking becomes more severe the higher the value of the parameter.
11) IMAX = defines the maximum current of the chopper both when running and in braking. All the current adjustments are expressed as a percentage of this value.
The adjustment interval is from 75% (level 0) to 100% (level 9).
12) MAX SPEED FORW = Max speed with forward direction on. This speed reduction goes under adjustable compensation with the COMPENSATION parameter.
13) MAX SPEED BACK = Max speed with backward direction on. This speed reduction goes under adjustable compensation with the COMPENSATION parameter.
H3D regenerative traction Page 21
14) CREEP SPEED = defines the minimum voltage applied to the motor with the running request activated. Provides a more immediate response in starting off.
15) WEAK DROPOUT = threshold of current for opening the weakening contactor (if programmed as such and not as bypass, in which case the output threshold is fixed and not programmable).
16) CURVE BRAKING = current for curve braking, activated with RV1 request, if the
PWM is greater than 80% and the motor current less than 40%Imax.
This braking level is used also for the speed check.
17) CURVE TIME = curve braking time associated to RV1. If 0, braking is not carried out.
18) BACKING TIME = backing request activating time delay. If programmed at level 9 there is no time delay and the on status is present if a request is present.
5.4 ADJUSTMENT CHART
PARAMETERS
ACCELERATION DELAY
INVERS BRAKING
RELEASE BRAKING
PEDAL BRAKING
CUTBACK SP. (1-2-3)
COMPENSATION
BRAKING MODUL
I MAX. (VERSION 800A)
I MAX. (VERSION 1000A)
MAX. SPEED FORW-BACK
CREEP SPEED
WEAK DROPOUT
CURVE BRAKING
CURVE TIME
AUXILIARY TIME
BACKING TIME
UNIT
0 1 2
PROGRAMMED LEVEL
3
Sec.
0.41
0.82
1.2
1.6
% IMax.
19 23 28 32
4
2
37
5
2.4
41
6
2.9
46
7
3.3
50
8
3.7
55
9
4.1
59
% IMax.
15
% IMax.
25
19
31
23
37
27
43
31
49
34
56
38
62
42
68
46
74
50
80
% VBatt.
10
K (I) 0.1
22
0.2
33
0.3
45
0.4
53
0.5
61
0.6
69
0.7
78
0.8
88
0.9
100
1
% IMax.
0
Amp.
600
3
622
5
644
8
667
11
689
14
711
17
733
20
755
22
778
25
800
Amp.
750 778 806 833 861 889 916 944 972 1000
% VBatt.
10
% VBatt.
0
22
1.9
33
3.9
45
5.9
53
7.8
61
9.8
69
11.7
78
13.7
88
16.6
100
17.6
% IMax.
10
% IMax.
15 sec.
sec.
sec.
0
0.1
0.05
20
19
0.2
0.5
0.2
30
23
0.3
2
0.35
40
27
0.4
4
0.5
50
31
0.6
7
0.75
60
34
0.8
9
1.0
70
38
1
12
1.5
80
42
1.2
14
2.0
90
46
1.6
17
2.5
100%
50
2
20 cont.
Page 22 H3D regenerative traction
5.5 WIRING DIAGRAM FOR H3D REGENERATIVE
H3D regenerative traction Page 23
5.6 WIRING DIAGRAM FOR H3D REGENERATIVE WITH BYPASS AND DOUBLE
LEVER PEDAL
Page 24 H3D regenerative traction
5.7 WIRING DIAGRAM FOR H3D REGENERATIVE WITH FIELD WEAKENING AND
POWER STEERING CONTACTOR
N.B.: The option AUX. FUNCTION must be selected in the HYDRO CONTACTOR mode.
H3D regenerative traction Page 25
5.8 WIRING DIAGRAM FOR H3D REGENERATIVE WITH BACKING
N.B.: For the operating of the backing request, program the option PIN F2 in the
BACKING mode.
DONT use the input F2 with this cabling configuration.
Page 26 H3D regenerative traction
5.9 H3D REGENERATIVE WITH SPEED CHECK
The speed or the revolutions of the Motor are measured by a gear wheel and a magnetic sensor (pick-up). The frequency of the signal sent to the logic is changed in to a voltage signal for the processing. The speed check is activated even if there is not the running request, therefore affording a descent without pressing the accelerator pedal the machine begins to brake automatically if it exceeds the minimum speed which is the 10% of the maximum speed set.
N.B.: The speed check in standby is not operating in case the option RELEASE OF the menu SEL OPTION is programmed FREE.
For configuring the controller follow these instructions:
- To have active the speed check function active you have to select by console the option SPEED of the menu SEL OPTION and program it to the check mode, then close on the logic board the jumper JP4. For working on the jumpers you have to equip yourself of a tin solder (25W - 40W), tin wire for electronic components and some lengths rheophores or copper wire not enamelled for making the jumper.
Pay attention: disconnect the battery and discharge the power capacitors before working on the electric parts.
- For setting the maximum speed with the trimmer R22 fitted on the logic board, you have to select the jumper JP5 = close.
- If instead of the internal trimmer it is used an external potentiometer for setting the maximum speed, select the jumper JP5 = open.
- For obtaining the maximum precision from the reading of the Motor revolutions it is necessary to select the jumper JP1, JP2, JP3 according to the scheme below:
Example: The requests are revolutions 2500 RPM max and on the drive shaft is connected with a 4 - gear wheel. For the selection of the jumpers positions point from the scheme where the 2500 rpm line crosses the 4 - gear line, then modify the jumpers like as in the table under the scheme; in our case it has to be used the table from 88 kHz to 175 kHz.
H3D regenerative traction Page 27
5.10 WIRING DIAGRAM FOR H3D REGENERATIVE WITH PICK-UP
R* = The value of the resistance is double than the one installed in the potentiometer; it is necessary for limiting the regulation range.
Page 28 H3D regenerative traction
5.10.1 Wiring modification when using a proximity sensor
With OPEN COLLECTOR proximity sensors it is necessary to fit a resistance in the external cabling like indicated in the scheme.
5.10.2
Notes on the gear wheel dimensions
- Using a magnetic pick-up the gear must have the same dimensions as the facing part of the sensors.
- With a proximity sensor the gear must have equal or bigger dimension than the facing part.
- In both cases the thickness of the plate must be bigger than the facing part.
H3D regenerative traction Page 29
6 H3D STANDARD TRACTION
- Input for 3 - wires potentiometer.
- N. 3 speed reductions.
- Handle or seat (delayed) microswitches input.
- Rapid inversion input.
- Pedal braking microswitch input.
- Bypass or weakening contactor handling.
- Handling of backing request with associated programmable speed.
Page 30 H3D standard traction
pin
F6
F7
F8
F9 function
F1 RV3
QUICK
F2 RV2
BACKING
F3 RV1
F4 MSEAT
F5 MF
MI
MA
RID
RID
6.1 INPUT CONNECTORS DESCRIPTION description
Input for 3rd speed reduction.
Rapid inversion request.
Input for 2nd speed reduction.
Backing request.
Input for 1st speed reduction with combined curve braking.
Input for seat microswitch signal (delayed 2 sec.) or handle signal.
Input for brake pedal microswitch: when the pin is taken (+VB) the speed No. 2 reduction is actived and the maximum current halved.
Input for backward request.
Input for forward request.
Like pin F4 but active low.
Like pin F4 but active low.
A detailed description of these pins is given on page 19.
6.2 PROGRAMMABLE FUNCTIONS DESCRIPTION (OPTIONS)
- The options can be programmed from the Console using the SEL OPTIONS menu.
Function
PIN G3 option by pass
Physically (C3) weak
BATTERY free check
ARB
HOURS
PIN E1
PIN E4
PIN E2 free check running key on cutb. #3 quick I seat handle cutb #2 backing description
Contactor with bypass
Contactor with weakening
No low battery charge alarm
Low charge alarm with maximum current reduced at
50%
No antirollback
Antirollback
Hour-meter only active when running
Hour-meter active with the key on
E1 = 3rd speed reduction
E1 = Input for rapid inversion
E4 = Seat microswitch
E4 = Handle microswitch
E2 = No. 2 speed reduction
E2 = Backing request
A detailed description of these pins is given on page 20.
H3D standard traction Page 31
6.3 ADJUSTMENT PARAMETER DESCRIPTION (MENU PROGRAM)
The parameters can be modified with the chopper standby or running. In the latter case, you must return to standby before switching off the chopper so that the modifications are stored in the choppers nonvolatile memory.
1 ACCELER.DELAY
Acceleration time
2 BRAKING
3 CUT BACK SP.1
4 CUT BACK SP.2
5 CUT BACK SP.3
Braking current - base value
1st speed reduction
2nd speed reduction
3rd speed reduction
6 AUXILIARY TIME Time delay to activate the auxiliary function
7 COMPENSATION Compensation for speed reductions
8 BRAKING MODUL.
Braking current increment in inversion with accelerator
9 IMAX.
Maximum chopper current
10 MAX SPEED FORW Maximum forward speed
11 MAX SPEED BACK Maximum reverse speed
12 CREEP SPEED
13 WEAK DROPOUT
14 CURVE BRAKINGCurve braking current (RV1)
15 CURVE TIME
16 BACKING TIME
Minimum acceleration threshold
Weakening output current threshold
Curve braking time 0 = no braking
Time delay to activate the back request, 9 = continuous
A detailed description of these parameters is given on page 21.
6.4 ADJUSTMENT CHART
PARAMETERS
ACCELERATION DELAY
BRAKING
CUTBACK SP. (1-2-3)
COMPENSATION
BRAKING MODUL
I MAX. (VERSION 800A)
I MAX. (VERSION 1000A)
UNIT
Sec.
% IMax.
10
% VBatt.
10
0 1 2
PROGRAMMED LEVEL
3
0.41
0.82
1.2
1.6
4
2
5
2.4
6
2.9
7
3.3
8
3.7
9
4.1
20
22
30
33
40
45
50
53
60
61
70
69
80
78
90
88
100%
100
K (I) 0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
% IMax.
0 3 5 8 11 14 17 20 22
1
25
Amp.
600 622 644 667 689 711 733 755 778 800
Amp.
750 778 806 833 861 889 916 944 972 1000
MAX. SPEED FORW-BACK % VBatt.
10
CREEP SPEED % VBatt.
0
WEAK DROPOUT
CURVE BRAKING
% IMax.
10
% IMax.
10
CURVE TIME
AUXILIARY TIME
BACKING TIME sec.
sec.
sec.
22
1.9
20
20
33
3.9
30
30
45
5.9
40
40
53
7.8
50
50
61
9.8
60
60
69
11.7
70
70
78
13.7
80
80
88
16.6
90
90
100
17.6
100%
100%
0 0.2
0.3
0.4
0.6
0.8
0.1
0.5
2 4 7 9
1
12
1.2
14
1.6
17
2
20
0.05
0.2
0.35
0.5
0.75
1.0
1.5
2.0
2.5
cont.
Page 32 H3D standard traction
6.5 WIRING DIAGRAM FOR H3D STANDARD WITH FIELD WEAKENING
H3D standard traction Page 33
7 TRACTION ADJUSTMENT AND DIAGNOSIS
7.1 SEQUENCE OF SETTINGS FOR REGENERATIVE/STANDARD TRACTION
- With the machine switched off, connect the programming console and then switch on.
If no wiring errors or component defects are found, the display shows the manufacturers name, programme release, configuration, and hour-meter value.
If the module has already been configured, the procedure passes directly to step four.
Otherwise, proceed in order as follows.
Consult the console manual for further procedure details.
1) Configure the chopper model (page 16-17).
2) Select the desired options (page 16-17).
3) Select and set battery voltage (page 16-17).
4) Check the operation of all the wired inputs, including the potentiometer, by means of the tester functions on the console.
5) Carry out accelerator signal acquisition on the PROGRAM VACC menu.
6) Set the maximum current by selecting the level corresponding to the desired value shown on the table of modifications (page 22).
7) Set accleration by moving the machine forward and backward.
8) Set the CREEP speed starting from level 0. With the machine stopped, press the pedal lightly in order to close the running microswitch, leaving the potentiometer at the minimum value, and then raise the level of the CREEP until the machine begins to move.
9) To set the speed reductions, activate the desired reduction request microswitch, take the compensation level to 0, set the speed (CUTBACK SP.l, etc.) with machine in standby on a flat surface and the accelerator pedal pressed all the way down.
Apply a load on the machine or put it in a slope keeping completely pressed the acceleraror pedal, and in these conditions set the compensation level until you reach the desired speed.
10) RELEASE BRAKING is set by running the machine and then completely releasing the accelerator pedal without pressing other pedals.
11) For INVERSION BRAKING, first set the MODUL BRAKING level at 0, run the machine and invert the direction with the pedal pressed down, then regulate the braking level.
12) MODUL BRAKING with accelerator. A parameter that increases the inversion braking according to the level of the accelerator signal; set it by inverting the direction with the pedal pressed all the way down. It is operating also with pedal braking equipped with a potentiometer.
13) Release braking with brake pressed (PEDAL BRAKING). Set by pressing the brake pedal lightly during release.
Page 34 H3D diagnosis traction
7.2 H3D TRACTION DIAGNOSIS
Description of the alarms signalled by the diagnostic LED.
The alarm code is shown in parentheses. A detailed description is given in the section
DECODING THE ALARMS DISPLAYED ON CONSOLE on page 36.
1 FLASH = Logic anomaly (EEPROM DATA KO, EEPROM PAR. KO,
EEPROM CONF. KO, EEPROM OFF-LINE, CHOPPER NO CONF,
WATCH-DOG).
2 FLASHES = Running request on startup or error in handle/speeds sequence
(INCORRECT START).
3 FLASHES = Error on VMN test (NO FULL CONDUCTION, VMN LOW).
4 FLASHES = Accelerator high in standby or failures in its connection: this error inhibits the operation (VACC NOT OK).
5 FLASHES = Error in reading current - this error inhibits operation (I HIGH AT STAND,
I=0 EVER).
6 FLASHES = Malfunction of the contactor driver circuit (DRIVER SHORTED,
COIL SHORTED).
7 FLASHES = Excessive temperature, greater than 80°C (TH. PROTECTION).
8 FLASHES = Contactors do not open or VMN high in standby (BRAKE CONT. OPEN,
DIR CONT. OPEN, VMN HIGH).
9 FLASHES = Contactor closed (BRAKE CON CLOSED) only for regenerative;
(DIR. CON CLOSED) only standard traction.
CONTINUOUS BLINKING (32 BLINKS) = Low battery charge, battery with <10% of residual charge (BATTERY).
LED REMAINS ON = Double running request (FORW BACK).
H3D diagnosis traction Page 35
7.3 DECODING CONSOLE DISPLAYED ALARMS
1) BRAKE CONT. CLOSED (only regenerative version)
Test carried out in the passage from running to initial regenerative braking.
If, on running contactor closure, the VMN is > 2/3 VBATT, an alarm is issued.
Possible causes: a) The normally open contact of the braking contactor is closed. Free the contact and clean it; if it is damaged replace the contactor.
b) The braking contactor remains excited for a defect in the logic board or because the NTFR wire is in short circuit toward negative.
To understand if the defect is produced by one of these causes, select the running and press the pedal without giving the seat or tiller request, if the activation only of the braking contactor is in synchrony with the pedal (or selector) command verify what follows: disconnect the wire from the NTFR connector and repeat the test above, if the contactor remains disactivated replace the logic, otherwise if the contactor moves check that there is not a wire shorted to a metallic part.
2) DIR. CONT. OPEN
Test carried out at running request: running contactor closure is verified by checking that the VMN signal is consistent. Possible causes: a) For finding out the causes follows the diagnosis procedure is as follows:
CONDITION UNDER
WHICH FAULT IS
DETECTED
ONLY AT FORWARD
RUNNING REQUEST
ONLY AT BACKWARD
RUNNING REQUEST
AT BOTH RUNNING
REQUEST
TEST
YOU SEE FORWARD
CONTACTOR (TA) CLOSING
FOR 0.3sec. THEN
OPENING?
YOU SEE BACKWARD
CONTACTOR (TI) CLOSING
FOR 0.3sec. THEN
OPENING?
YOU SEE FORWARD OR
BACKWARD CONTACTOR
(TA OR TI) CLOSING FOR
0.3sec. THEN OPENING
RESULT
YES
NO
YES
NO
YES
NO
TEST
→
WHEN REQUESTING
FORWARD RUNNING YOU
FIND ANY VOLTAGE AT
COIL CONTACTS FOR
0.3 sec.?
→
WHEN REQUESTING
BACKWARD RUNNING YOU
FIND ANY VOLTAGE AT
COIL CONTACTS FOR
0.3sec.?
→
WHEN REQUESTING
FORWARD RUNNING YOU
FIND ANY VOLTAGE AT TA
COIL'S CONTACTS (OR AT
BACKWARD CONTACTOR
COIL'S CONTACTS (BTI))
FOR 0.3sec.?
RESULT
→
FAULT
DESCRIPTION AT
POINT:
A1
YES
NO
→
YES
NO
→
YES
NO
B1
C1
A2
B2
C2
A3
B3
C3
A1) There is not a good contact either on TA (=forward contactor) NA (normally open) or on TI (=backward contactor) NC (normally closed), due to dust, dirt or any particles which prevent a good contact.
Clean contacts by means of compressed air; if necessary remove dirt applying a soft abrasive movement.
Page 36 H3D diagnosis traction
It could be necessary to change both contactors.
A2) There is not a good contact either on TI NA or on TA NC, due to dust, dirt or any particles which prevent a valid contact.
Clean contacts by means of compressed air; if necessary remove dirt applying a soft abrasive movement.
It could be neccessary to change both contactors.
A3) The most likely reason is that the normally closed contact of the braking contactor doesnt make a good contact towards the battery negative for dust, dirt or because the contact doesnt locate completely for a mechanical defect of the contactor.
It could be necessary to replace the contactor.
It may be due to 1 of following causes of motor connecting interruption: a) brushes open from the armature (fig.1).
b) brush cable burn up (fig.2).
c) Missing the braking contactor negative cable (fig. 3) d) Interruption either on motor winding or on motor cables.
H3D diagnosis traction Page 37
B1) Forward contactor (TA) is supplied with a correct voltage but does not close.
Possible causes:
1) Contactor coil is open circuit, verify its resistance using an ohmmeter.
2) Contact cant move due to some mechanical restriction.
3) Nominal working coil voltage is greater than the battery voltage.
B2) Reverse contactor (TI) is supplied with a correct voltage but it doesnt close; everything said at point B1 for TA is valid here.
B3) Reverse and forward contactors are supplied with correct voltage but they dont close; see point B1.
C1) Supply is not present at TA. Check cables and connections from TA coil to connectors C2 (PT) and C6 (NTA).
C2) Supply is not present at TI. Check cables and connections from TI coil to connectors C2 (PT) and C4 (NTI).
C3) Supply is not present at TA and TI. Check cables and connections from the coils to connectors C2 (PT), C6 (NTA) and C4 (NTI).
- For points C1, C2, C3 replacing controller may be necessary.
For H3D standard configuration the solutions at point A1-A2-A3-B1-B2-B3-C1-
C2-C3 are valid; for the last two points please respect the different connections rather than the regenerative configuration.
3) BRAKE CONT. OPEN (regenerative only)
Test carried out during the passage to running. After closing one of the direction contactors, the braking contactor closes, verifying that the VMN goes from < 1/3 to >
2/3. If this does not occur, an alarm is shown.
For finding the causes follow the diagnosis procedure as follows:
Page 38 H3D diagnosis traction
TEST
AT RUNNING REQUEST
THE TFR CLOSES FOR
0.3sec?
RESULT
YES
NO
2° TEST
→
WHEN THERE'S THE
RUNNING REQUEST, IS
THERE A VOLTAGE AT
PIN BTFR FOR A TIME OF
0.3sec?
ESITO
→
YES
3° TEST
→
CHECK WITH AN
OHMMETER IF THE TFR
COIL IS INTERRUPTED
RESULT
FAULT
DESCRIPTION
AT POINT
A4
→
A5
YES B4
NO
B5
B6
NO → → C4
A4) There is not a good contact on the NA of TFR, clean the contact, if it is damaged, replace the contactor.
A5) The positive cable on the braking contactor is missing.
B4) Replace the contactor coil or the complete contactor.
B5) Contactor mechanically locked, unlock it or replace it.
B6) Contactor has a working nominal voltage higher than the supply.
C4) Supply does not appear at the contactor coil, please check the cables and the connections from the coil to the connector C1(PTFR) and C5(NTFR).
4) DIR.CON.CLOSED
Test carried out during the passage to standby or braking.
Checks that the running contactor opens by comparing the consistent status of the
VMN potential. Possible causes: a) Running contactor welded or slow to open.
b) Logic failure.
H3D diagnosis traction Page 39
5) VMN LOW
The test is carried out at standby and in running up to 80% of PWM. If the VMN voltage is lower than 1/3 of the battery voltage, an alarm is shown.
For finding out the causes follow the diagnosis procedure has follows:
CONDITIONS
UNDER WHICH
FAULTS IS
DETECTED
1° TEST RESULT
AT THE KEY ON
DISCONNECT THE
MOTOR CABLE
CONNECTED TO
THE BATTERY
AND THEN VERIFY
IF THE ALARM
STILL PRESENT
YES
NO
2° TEST
→
A RUNNING
CONTACTOR IS
LOCKED IN
WORKING
POSITION
RESULT
→
3° TEST
→
RESULT
FAULT
DESCRIPTIO
POINT:
→
YES
THE STUCK
CONTACTOR COIL
IS SUPPLIED?
YES
NO
NO
C5
B7
B8
D1
D2
D3
RUNNING WITH
CONTACTORS ON
RUNNING
POSITIONS
→
AS SOON AS THE
ACCELERATOR
PEDAL IS
COMPLETLY
RELEASED FOR
DOING A RELEASE
BRAKING
IS IT PRESENT
THE BYPASS OR
THE WEAKENING
CONTACTOR?
→
YES
NO
→
→
→
→
→
→
→
→
→
→
→
→
C5
E1
C5
B7) If the running contactor remains closed, you can verify:
1) if the wire going from NTA to NTI is shorted to a metallic part connected to the battery negative;
2) disconnecting the contactor wire always excited from board connector if the contactor is no longer excited, replace the logic board.
B8) A running contactor remains in the working position, free the contact, it may be necessary to replace the contactor.
D1) Wrong connections of the motor cables. The stator and the armature are crossed.
Page 40 H3D diagnosis traction
D2) There is current leakage in the motor between the stator winding and the armature. Otherwise there are some electric parts of these windings that makes a contact inside the motor.
D3) Check that there are no metallic parts inside the contactor board that cause a short towards the negative in the points connected to SH- and SH+.
C5) The most probably reason is that the failure is inside the controller, replace it.
E1) If a bypass contactor is present check that it is not welded or it is too slow opening.
To verify this possibility, disconnect the bypass and check if the failure disappears: if this happens, replace the logic.
ATTENTION: the contactors connected to the controller must not have arc suppression on the contactor coils. Suppression exists inside the controller.
Any external suppresion will modify the contactor opening times.
6) VMN HIGH
Test carried out in standby. If the VMN voltage is greater than 2/3 VBATT, an alarm is shown. Possible causes: a) Contactor welded (only standard traction).
b) Short circuit between +BATT and VMN, check if there are any metallic parts causing short circuit in the contactor board.
c) Logic failure, probably the braking diode has failed, replace the power board.
7) NO FULL COND.
The test is carried out in full conduction. In this condition, if the VMN is found to be greater than 1/3 VBATT, the diagnostic circuit is faulty, causing a safety risk, and thus machine operation is inhibited. If the defect persists, replace the logic.
8) THERMAL PROTECTION
An indication that the controller temperature has exceeded 80° C.
The maximum current is gradually reduced, reaching 0 at a temperature of 85° C.
a) If the alarms occurs while cold, the most probably reason is failure of the thermal diagnosis circuit on the power or on the logic board, replace one of the two parts or replace the complete controller.
b) If the alarm occurs frequently the machine has worked for a short time, it is probably due to inadequate heat sinking. Check the fixing nuts are tight and the installation is correct .
9) BATTERY
The battery charge is low.
The alarm is signalled only if the battery check option has been selected from the serial console (default). When this alarm occurs, the maximum current is reduced to
50%.
H3D diagnosis traction Page 41
10) INCORRECT START
An incorrect starting sequence.
The machine only starts if the sequence is followed: key-handle (or seat) - running.
Possible causes: a) Running microswitch or handle microswitch closed.
b) Error in sequence made by the operator, pedal pressed at the key on.
c) Incorrect wiring if there are not any defects externally it is necessary to replace the logic..
11) FORW - BACK
The test is carried out continuously. An alarm is signalled when two requests for running are made simultaneously. Possible causes: a) Defective wiring.
b) Running microswitch closed.
c) Incorrect manoeuvre.
d) If there are no external defects, replace the logic.
12) VACC NOT OK
The test is made in standby.
The alarm indicates that the accelerator voltage is greater than 1V with respect to the minimum value stored. Possible causes: a) A potentiometer wire is open circuit or the potentiometer negative has not been connected to the PIN D2 of the logic board. In this case an alarm is generated because the logic does not find the load on pin D2.
b) The potentiometer is not correctly calibrated.
c) The potentiometer is defective (interrupted).
13) I HIGH AT STAND
Test carried out in standby. Checks that the current is zero.
If this is not verified, an alarm is signalled. This alarm inhibits machine operation.
Possible causes: a) Current sensor broken or logic failure.
First replace the logic. If the defect persists, replace the power unit.
14) I=0 EVER
Test carried out in running.
Checks that the current during running is greater than a minimum value. If not, an alarm is signalled and the machine is shut down. Possible causes: a) The current sensor is faulty. Replace the power unit.
b) Incorrect connection of the motor cables to the power bars SH- and SH+.
15) EEPROM PAR.KO
Fault in the area of memory in which the adjustment parameters are stored. This alarm inhibits machine operation. If the defect persists when the key is switched off and on again, replace the logic. If the alarm disappears, remember that the parameters stored previously have been cancelled and replaced by the default values.
Page 42 H3D diagnosis traction
16) EEPROM CONF.KO
Fault in the area of memory in which the special chopper configuration data is stored. If the defect persists when the key is switched off and on again, replace the logic. Otherwise, remember that the chopper configuration has been reset to the default values (regeneration version, etc.); thus it must be reprogrammed.
Consult the console manual.
17) EEPROM DATA KO
The data in the area of memory for the hour-meter is incorrect. This alarm does not shut down the machine. If the alarm disappears when the key is switched off and on again, remember that the hour-meter data has been reset to zero.
18) EEPROM OFF LINE
Fault in the nonvolatile memory that contains data relative to the area for the hourmeter, the alarms stored and the programming parameters.
If the alarm persists when the key is switched off and on again, replace the logic.
19) CHOP NO CONF.
An alarm similar to no. 16, except that here, even though the data is correct, it does not correspond to a hardware configuration recognised by the H2B. The considerations are the same as for alarm 16 EEPROM CONF.KO.
20) WATCHDOG
The test is made in both running and standby.
It is a self-diagnosis test within the logic. If an alarm should occur, replace the logic.
21) SHORTED COIL
An overload or a short circuit toward +BATT on the contactor negative driver outputs.
Possible causes: a) The contactor coils are short circuit or draw more than 6 A continuous.
b) Short circuit with +BATT of the wiring that comes from the contactor connector.
The alarm indicates the occurrence of an overload, not the breakdown of a chopper component. Once the external cause is removed, the chopper can be restarted.
22) DRIVER SHORTED
The test is carried out in standby, and checks that the voltage of the drivers that control the contactors is consistent with the preset value.
Possible causes: a) Logic failure.
b) Driver breakdown caused by overvoltage in the contactor negative wiring.
Replace the logic after having removed the cause.
H3D diagnosis traction Page 43
8 H3D STANDARD LIFTING
- Input for speed controlled by 3-wire potentiometer
- 4 speeds with separately adjustable compensation
- 1 speed with associated delay (for hydrodrive) and adjustable compensation
- Main contactor handling
- Weakening or bypass contactor handling
- Proportional solenoid valve handling for descent
Page 44 H3D standard lifting
pin function
F1
F2
F3
F4
F5
F6
4TH S.
3RD S.
2ND S.
HYD. S.
1ST S.
DOWN
F7 UP
F8 HYD.S.
F9 HYD.S.
8.1 INPUT CONNECTORS DESCRIPTION description
Input for 4th speed request.
The speed is active when the pin is high, connected to +Batt.
Input for 3rd speed request.
The speed is active when the pin is high, connected to +Batt.
Input for 2nd speed request.
The speed is active when the pin is high, connected to +Batt.
Input for hydrodrive speed request.
The speed is active when the pin is high, connected to +Batt.
The programmable timing (HYDRO TIME) is related to this input.
Input for 1st speed request.
The speed is active when the pin is high, connected to +Batt.
Input for descent request. When this input is active, it is possible for the potentiometer to handle a proportional solenoid valve connected to connectors C2 and C5.
Input for speed request handled by potentiometer, active high..
Same function as F4 but active when forced to -BATT.
Like Pin F8.
8.2 PROGRAMMABLE FUNCTIONS DESCRIPTION (OPTIONS)
These options can be programmed from the console with the SEL OPTIONS menu.
function/pin option description
PIN G3
Physically (C3)
BATTERY free
HOURS bypass weak check running key on
PIN G5 status
Physically (C4) main c.
The contactor connected to connector C3 is handled as bypass.
Activation current = <80% IMAX.
Output current = <90% IMAX.
Activation delay = 800 ms.
The contactor connected to connector C3 is handled as field weakening. Activation current 50% of the output current.
Output current is programmable.
(WEAK DROP OUT) from 10% to 100% IMAX.
No low battery charge alarm.
Activates the test that reads the battery charge in standby.
This value constitutes the level of residual battery charge and is compared with a table in memory.
When the charge is less than 10%, all functions are blocked except for the hydrodrive, and the LED signals this condition by flashing continuously.
Hour-meter active only in running.
Hour-meter active with key.
The output relative to pin C4 is active when the chopper is carrying out any function (except descent).
The output relative to pin C4 handles a main contactor.
H3D standard lifting Page 45
8.3 H3D STANDARD LIFTING ADJUSTMENT PARAMETERS DESCRIPTION
The parameters can be modified with the controller both in standby and in running.
For storing the modifications in the nonvolatile memory, you must go out from the menu program and confirm the ENTER request.
1) ACCELER.DELAY = Pump motor acceleration time
2) EV. ACCELER DELAY = Acceleration time relative to descent (proportional solenoid valve).
3) DECELER DELAY = Deceleration time, i.e. to annul the voltage on the motor upon release.
4) EV.DECELER DELAY = Deceleration time relative to descent.
5) AUXILIARY TIME = Not used in the pump configuration.
6) IMAX. = Defines the maximum chopper current. All current adjustments are expressed as a percentage of this value. The adjustment range is from 50% (level 0) to
100% (level 9).
7) HYD SPEED COARSE = Coarse hydrodrive speed (from 0 to 100% Vbatt on the motor).
8) HYD SPEED FINE = Fine hydrodrive speed (a value from 0 to 10% Vbatt is added to the coarse speed value). The speed is given by: motor voltage = [(coarse speed) x 10 + (fine speed)] x Vbatt /100
The interval of values ranges from 0 to total conduction.
9) HYDRO COMPENS = Compensation in current for hydrodrive request.
10) CREEP SPEED = Defines the minimum value of voltage applied to the motor with running request active. Allows a more immediate response at start up.
11) WEAK DROPOUT = Threshold of current for opening the weakening contactor (if programmed as such and not as bypass, in which case the output threshold is fixed and not programmable).
12) HYDRO TIME = Hydrodrive delay time. If set at 0, there is no delay; thus the hydrodrive input can be handled as a 5th speed.
13) 1ST SPEED COARSE = Speed no. 1, coarse adjustment.
14) 1ST SPEED FINE = Speed no. 1, fine adjustment.
15) 1ST SPEED COMP. = Compensation speed no.1.
16) 2ND SPEED COARSE = Speed no. 2, coarse adjustment.
17) 2ND SPEED FINE = Speed no. 2, fine adjustment.
18) 2ND SPEED COMP. = Compensation speed no.2.
19) 3RD SPEED COARSE = Speed no. 3, coarse adjustment.
20) 3RD SPEED FINE = Speed no. 3, fine adjustment.
21) 3RD SPEED COMP. = Compensation speed no.3.
22) 4TH SPEED COARSE = Speed no. 4, coarse adjustment.
23) 4TH SPEED FINE = Speed no. 4, fine adjustment.
24) 4TH SPEED COMP. = Compensation speed no.4.
25) MIN. VALVE VOLT. = Minimum voltage applied on the proportional solenoid valve.
26) MAX. VALVE VOLT. = Maximum voltage applied on the proportional solenoid valve.
Page 46 H3D standard lifting
8.4 ADJUSTMENT CHART FOR H3D STANDARD LIFTING
PARAMETERS
ACCELERATION DELAY
EV. ACCELER DELAY
DECELER DELAY
EV. DECELER DELAY
I MAX. (VERSION 800A)
I MAX. (VERSION 1000A)
SPEED COARSE
SPEED FINE
HYDRO COMPENS
CREEP SPEED
WEAK DROPOUT
HYDRO TIME
MIN VALVE VOLT
MAX VALVE VOLT
UNIT
Sec.
Sec.
Sec.
Sec.
0
0.15
0.39
1
0.24
0.63
2
0.39
0.71
PROGRAMMED LEVEL
3
0.50
0.81
4
0.63
0.97
5
0.74
1.05
6
0.86
1.27
7
0.97
1.36
8
1.09
1.46
9
1.22
1.54
0.06
0.13
0.19
0.25
0.31
0.38
0.44
0.50
0.56
0.62
0.30
0.60
0.70
0.78
0.95
1.04
1.26
1.36
1.43
1.53
Amp.
600 622 644 667 689 711 733 755 778 800
Amp.
750 778 806 833 861 889 916 944 972 1000
% VBatt.
0
% VBatt.
0
K (I)% 10
11 22 33 44 55 66 77 88 100
1.2
2.4
3.6
4.8
6.05
7.3
8.5
9.7
10.9
20 30 40 50 60 70 80 90 100
%VBatt.
0
%IMax.
10
1.9
3.9
5.9
7.8
9.8
11.7
13.7
16.6
17.6
20 30 40 50 60 70 80 90 100 sec.
0 0.5
2 4 7 9 12
%VBatt.
7.4
11.3
15.2
19.2
23.1
27.0
31
%VBatt.
56 60 64.5
70
14
35
17
39
20
43
74 78.5
83.5
88 92.5
97.5
H3D standard lifting Page 47
8.5 WIRING DIAGRAM FOR H3D STANDARD LIFTING
Page 48 H3D standard lifting
8.6 WIRING DIAGRAM FOR H3D STANDARD LIFTING WITH FIELD WEAKENING
H3D standard lifting Page 49
8.7 WIRING DIAGRAM FOR H3D STANDARD LIFTING WITH BYPASS AND MAIN
CONTACTORS. POWER STEERING COMMAND FROM RUNNING CONTACTORS
(*)
Page 50 H3D standard lifting
9 H3D LIFTING + 3RD MOTOR
- Input for speed control by potentiometer
- 4 speeds with separately adjustable compensation
- Contactor handling with programmable delay (3rd hydrodrive motor)
- Main contactor handling
- Weakening or bypass contactor handling
- Proportional solenoid valve handling for descent
H3D lifting + 3rd motor Page 51
pin function
F1
F2
F3
F4
F5
F6
4TH S.
3RD S.
2ND S.
HYD. S.
1ST S.
DOWN
F7 UP
F8 HYD.S.
F9 HYD.S.
9.1 INPUT CONNECTORS DESCRIPTION description
Input for 4th speed request.
The speed is active when the pin is high, connected to +Batt.
Input for 3rd speed request.
The speed is active when the pin is high, connected to +Batt.
Input for 2nd speed request.
The speed is active when the pin is high, connected to +Batt.
Input for hydrodrive speed request.
The speed is active when the pin is high, connected to +Batt.
The programmable timing (HYDRO TIME) is associated to this input.
Input for 1st speed request.
The speed is active when the pin is high, connected to +Batt.
Input for descent request. When this input is active, it is possible for the potentiometer to handle a proportional solenoid valve connected to connectors C2 and C5.
Input for speed request handled by potentiometer, active high..
Same function as F4 but active when forced to -BATT.
Like Pin F8.
9.2 PROGRAMMABLE FUNCTIONS DESCRIPTION (OPTIONS) unction/pin option meaning
PIN G3 Bypass
Weak
Bypass contactor.
Weakening contactor.
BATTERY
HOURS
PIN G5
Free
Check
Running
Key on
Status
Main C.
No low battery charge alarm.
Low battery charge alarm which blocks all functions except hydrodrive.
Hour-meter active only in running.
Hour-meter active for the entire chopper startup time.
Output C4 = Lifting status (0=running).
Output C4 = Main contactor.
A detailed description of the meanings is the same given on page 45 as per H3D standard lifting.
Page 52 H3D lifting + 3rd motor
9.3 H3D LIFTING + 3RD MOTOR ADJUSTMENT PARAMETERS DESCRIPTION
1 ACCELER.DELAY
2 EV. ACCELER DELAY valve)
3 DECELER DELAY
4 EV.DECELER DELAY
5 AUXILIARY TIME
6 IMAX.
7 CREEP SPEED
8 WEAK DROPOUT
9 HYDRO TIME
(Pump acceleration time - rise/functions)
(Acceleration time descent proportional solenoid
(Pump deceleration time)
(Deceleration time proportional solenoid valve)
(Not used for the H3D in pump configuration)
(Maximum chopper current)
(Minimum acceleration threshold)
(Weakening output current threshold)
(Hydrodrive delay)
(Speed no. 1 - coarse adjustment 0-100%)
(Speed no. 1 - fine adjustment 10%)
(Compensation speed no. 1)
10 1ST SPEED COARSE
11 1ST SPEED FINE
12 1ST SPEED COMP.
13 2ND SPEED COARSE
14 2ND SPEED FINE
15 2ND SPEED COMP.
16 3RD SPEED COARSE
17 3RD SPEED FINE
18 3RD SPEED COMP.
19 4TH SPEED COARSE
(Speed no. 2 - coarse adjustment 0-100%)
(Speed no. 2 - fine adjustment 10%)
(Compensation speed no. 2)
(Speed no. 3 - coarse adjustment 0-100%)
(Speed no. 3 - fine adjustment 10%)
(Compensation speed no. 3)
(Speed no. 4 - coarse adjustment 0-100%)
20 4TH SPEED FINE
21 4TH SPEED COMP.
22 MIN. VALVE VOLT.
(Speed no. 4 - fine adjustment 10%)
(Compensation speed no. 4)
(Minimum voltage on solenoid valve)
23 MAX. VALVE VOLT.
(Maximum voltage on solenoid valve)
A detailed description of the parameters is given at page 46 as per H3D standard lifting.
H3D lifting + 3rd motor Page 53
9.4 ADJUSTMENT CHART FOR H3D STANDARD LIFTING + 3RD MOTOR
PARAMETERS
ACCELERATION DELAY
EV. ACCELER DELAY
DECELER DELAY
EV. DECELER DELAY
I MAX. (VERSION 800A)
I MAX. (VERSION 1000A)
SPEED COARSE
SPEED FINE
COMPENSATION
CREEP SPEED
WEAK DROPOUT
HYDRO TIME
MIN VALVE VOLT
MAX VALVE VOLT
UNIT
Sec.
Sec.
Sec.
Sec.
0
0.15
0.39
Amp.
Amp.
% VBatt.
0
% VBatt.
0
K (I)% 10
1
0.24
0.63
2
0.39
0.71
PROGRAMMED LEVEL
3
0.50
0.81
4
0.63
0.97
5
0.74
1.05
6
0.86
1.27
7
0.97
1.36
8
1.09
1.46
9
1.22
1.54
0.06
0.13
0.19
0.25
0.31
0.38
0.44
0.50
0.56
0.62
0.30
0.60
0.70
0.78
0.95
1.04
1.26
1.36
1.43
1.53
600 622 644 667 689 711 733 755 778 800
750 778 806 833 861 889 916 944 972 1000
11 22 33 44 55 66 77 88 100
1.2
2.4
3.6
4.8
6.05
7.3
8.5
9.7
10.9
20 30 40 50 60 70 80 90 100
%VBatt.
0
%IMax.
10
1.9
3.9
5.9
7.8
9.8
11.7
13.7
16.6
17.6
20 30 40 50 60 70 80 90 100 sec.
0 0.5
2 4 7 9 12
%VBatt.
7.4
11.3
15.2
19.2
23.1
27.0
31
%VBatt.
56 60 64.5
70
14
35
17
39
20
43
74 78.5
83.5
88 92.5
97.5
Page 54 H3D lifting + 3rd motor
9.5 WIRING DIAGRAM FOR CONNECTION LIFTING PUMP AND POWER
STEERING WITH BYPASS AND MAIN CONTACTORS. POWER STEERING
COMMAND FROM RUNNING CONTACTORS.
H3D lifting + 3rd motor Page 55
10 H3D LIFTING ADJUSTMENT AND DIAGNOSIS
10.1 SEQUENCE OF SETTING FOR LIFTING
- With the machine switched off, connect the programming console and then switch on.
If no wiring errors or component defects are found, the display shows the manufacturers name, programme release, configuration, and hour-meter value.
If the module has already been configured, the procedure passes directly to step four.
Otherwise, proceed in order as follows.
Consult the console manual for further procedure details.
1) Configure the chopper model (page 16).
2) Select the desired options (page 53).
3) Select and set battery voltage (page 17).
4) Check the operation of all the wired inputs, including the potentiometer, by means of the Tester functions on the console.
5) Carry out accelerator signal acquisition on the PROGRAM VACC menu.
6) Set the maximum current by selecting the level corresponding to the desired value.
7) Set the speed of the respective functions with the machine in standby, and the level of compensation set at 0. Then apply a load and set the compensation until it reaches the desired speed.
As the adjustments of speed and compensation are interdependent, further adjustments must be made before reaching the optimum condition.
8) Set the hydrodrive speed in the same way as the others, with the only difference being that the speed is set with the steering in standby, while the compensation is set with the steering under load.
9) Set acceleration, deceleration, and creep as necessary.
10.2 SETTING THE PROPORTIONAL SOLENOID VALVE
- For control of the solenoid valve, it is necessary to fit the potentiometer and the descent request microswitch.
1) Carry out the potentiometer signal acquisition using the PROGRAM VACC function.
2) With the lever in minimum speed position, set the MIN VALUE VOLT parameter by incrementing the level until it begins to descend.
3) With the lever in maximum speed position, set the MAX VALUE VOLT parameter by decreasing the level until you notice that the descent speed begins to reduce.
4) Acceleration and deceleration are set by obtaining the best compromise between response speed and smoothness of movement.
Page 56 H3D seting and diagnosis lifting
10.3 H3D LIFTING DIAGNOSIS
Description of the alarms signalled by the diagnostic LED.
The alarm code is shown in parentheses. A detailed description is given in the section
DECODING THE ALARMS DISPLAYED ON CONSOLE.
1 FLASH = Logic anomaly (EEPROM DATA KO, EEPROM PAR. KO, EEPROM
CONF. KO, EEPROM OFF-LINE, CHOPPER NO CONF, WATCH-
DOG).
2 FLASHES = Running request on startup or error in handle/speeds sequence
(INCORRECT \ START).
3 FLASHES = Error on VMN test (NO FUL CONDUCTION).
4 FLASHES = Accelerator high in standby - this error inhibits machine operation
(VACC > 1 V).
5 FLASHES = Error in reading current - this error inhibits machine operation
(1 HIGH AT STAND, I=0 EVER).
6 FLASHES = Malfunctioning of the contactor driver circuit (DRIVER SHORTED,
COIL SHORTED).
7 FLASHES = Excessive temperature, greater than 80°C (TH. PROTECTION).
CONTINUOUS FLASHES (32 FLASHES) = Low battery charge, battery with < 10% of
residual charge (BATTERY).
10.4 DECODING CONSOLE DISPLAYED ALARMS
1) STAND BY VMN LOW
The test is carried out in standby. If the VMN voltage is lower than 1/3 of the battery voltage, an alarm is signalled. Possible causes: a) Check the motor wiring to make sure it is correct.
b) Chopper failure, replace the unit.
2) NO FULL COND.
The test is carried out in full conduction.
If, in this condition, the VMN is found to be greater than 1/3 VBATT, the diagnostic circuit is faulty, causing a safety risk, and thus machine operation is inhibited. If the defect persists, replace the logic.
3) TH.PROTECTION
An indication that the chopper temperature has exceeded 80°C.
The maximum current is gradually reduced, reaching 0 at a temperature of 85°C. If the alarm occurs while cold: a) Check the thermal sensor connection.
b) Thermal sensor failure.
c) Connection of the power circuit has been interrupted (check the connector that connects the logic to the power unit).
d) Logic failure.
H3D seting and diagnosis lifting Page 57
4) BATTERY
The battery charge is low.
The alarm is signalled only if the BATTERY CHECK option has been selected.
All functions except hydrodrive are inhibited.
5 ) INCORRECT START
A running request is present on key startup.
Possible causes: a) Operator error.
b) Request microswitch closed.
The presence of the power steering request at the key on does not generate the alarm.
6) I HIGH AT STAND
Test carried out in standby, checks that the current is zero.
If this is not verified, an alarm is signalled. This alarm shuts down the machine.
Possible causes: a) Current sensor failure and logic failure.
First replace the logic, and if the defect persists, replace the power unit.
7) I=0 EVER
Test carried out in running.
Checks that the current during running is greater than a minimum value. If not, an alarm is signalled and the machine is shut down. Possible causes: a) The current sensor is faulty. Replace the power unit.
8) EEPROM PAR.KO
Fault in the area of memory in which the adjustment parameters are stored. This alarm inhibits machine operation.
If the defect persists when the key is switched off and on again, replace the logic.
If the alarm disappears, remember that the parameters stored previously have been cancelled, and replaced by the default values.
9) EEPROM CONF.KO
Fault in the area of memory in which the special chopper configuration data is stored. If the defect persists when the key is switched off and on again, replace the logic. Otherwise, remember that the chopper configuration has been reset to the default values (regeneration voltage, etc.); thus it must be reprogrammed. Consult the console manual.
10) EEPROM DATA KO
The data in the area of memory that handles the hour-meter is incorrect. This alarm does not shut down the machine. If the alarm disappears when the machine is switched off and on again, remember that the hour-meter data has been reset to zero.
11) EEPROM OFF LINE
Fault in the nonvolatile memory that contains data relative to the area for the hourmeter, the alarms stored and the programming parameters.
If the alarm persists when the key is switched off and on again, replace the logic.
Page 58 H3D seting and diagnosis lifting
12) CHOP. NO CONF.
An alarm similar to no.9, except that here, even though the data is correct, it does not correspond to a hardware configuration recognised by the H2B. The considerations are the same as for alarm 9 EEPROM CONF.KO.
13) WATCHDOG
The test is made in both running and standby.
It is a self-diagnosis test within the logic.
If an alarm should occur, replace the logic.
14) SHORTED COIL
There is a short circuit towards the positive of the battery, somewhere on the negative contactor output.
Possible causes: a) The coils of the contactors are short circuit or they draw more than 6A continuously.
b) Short circuit with +batt of the cables which come out from the contactor connector.
The alarm shows an that overchange has occoured and not the failure of a chopper component. When the external cause is removed it is possible to restart again.
15) SHORTED DRIVER
The test is carried out in standby. It checks that the voltage of the drivers controlling the contactors is within limits compared to previously stated values.
Possible cause: a) Logic failure
B) Drivers failed because of an overvoltage in the cables of the negative contactors.
Replace the logic after having removed the cause.
H3D seting and diagnosis lifting Page 59
RECOMMENDED SPARE PARTS FOR H3D
ARTICLE
CODE NO
E07008
C22000
C16506
C16507
C12373
C12371
C12372
C12370
C12397
C12769
C12203
C12205
C12768
C12228
C12229
C12767
C12204
C12230
C29509
C29537
C29510
C29523
C29514
C15312
P00114
DESCRIPTION
Potentiometer 5Kohm 330
Microswitch 10A 250V 1-way
Protected power fuse 425A
Protected power fuse 500A
9-way molex female connector
3-way molex female connector
8-way molex female connector
2-way molex female connector
10-way molex female connector
Female connector (molex)
6-way mate-in-lock FE connector
4-way mate-in-lock FE connector
Male connector (for female lock)
4-way mate-in-lock MA connector
6-way mate-in-lock MA connector
Female connector (for male lock)
9-way mate-in-lock FE connector
9-way mate-in-lock MA connector
Contactor SW 200 80V (300D)
Contactor SW 201-6-80V (300R)
Contactor SW 201-65-80V (300R)
Contactor SW 180 B13-80V (180D)
Contactor SW 80 80V
H3D black plastic cover
Logic Board H3D ABDZPA0B
Page 60 H3D
PERIODIC MAINTENANCE TO BE REGULARLY REPEATED
Check the wear of electric contacts: they should be replaced when matchboard is too strong and worn-out. Electric contacts should be checked every 3 months.
Check pedal microswitch: verify with a tester that there is no electric resistance between the contacts by measuring the voltage drop between its terminals. Also the release should have a firm sound. The pedal microswitch should be checked every 3 months.
Check motor-battery power links: they should be in excellent condition as well as the cable insulation. Wires should be checked every 3 months.
Control of the pedal and contactors springs. They should be able to extend to full extention and checked every 3 months.
Check contactor mechanical movements. They should be frictionfree and not restricted.
Mechanical movements of the contactors should be checked every 3 months.
Checks should be done by skilled personnel only and, all spare parts should be original.
Installation of this electronic controller should be done according to the diagrams included in this manual and any variation should be done accordingly with the supplier.
The supplier is not responsible for any problem that rises from using wiring solutions different from the ones suggested in this manual.
Any cause which is visible or recognized by an ordinary technician who periodically checks the equipment, that can create damage or defects to the device should be transmitted to the ZAPI's technician or to the technical commercial net.
They will take the responsibility for possible decisions regarding the operational safety of the electric vehicle.
DO NOT USE A VEHICLE WITH A
FAULTY ELECTRONIC CONTROLLER
H3D Page 61

Public link updated
The public link to your chat has been updated.
Advertisement
Key features
- Regenerative traction control
- Standard traction control
- 5-speed lifting pump control
- 4-speed lifting pump control with power steering contactor handling
- Optimum sensitivity to low speeds
- Self-diagnostics
- Configuration by console/mini-console
- Parameter modification by console