null  null
INVERTER
INSTALLATION GUIDELINE
FR-F740-00023 to 12120-EC
Thank you for choosing this Mitsubishi Inverter.
Please read through this Installation Guideline and a CD-ROM enclosed to operate this inverter correctly.
Do not use this product until you have a full knowledge of the equipment, safety information and
instructions.
Please forward this Installation Guideline and the CD-ROM to the end user.
1
CONTENTS
INSTALLATION OF THE INVERTER AND INSTRUCTIONS................. 1
2
OUTLINE DRAWING............................................................................... 2
3
WIRING.................................................................................................... 3
4
PRECAUTIONS FOR USE OF THE INVERTER..................................... 8
5
FAILSAFE OF THE SYSTEM WHICH USES THE INVERTER .............. 9
6
PARAMETER LIST................................................................................ 10
7
TROUBLESHOOTING........................................................................... 16
700
WARNING
CAUTION
The
CAUTION level may even lead to a serious consequence according
to conditions. Both instruction levels must be followed because these are
important to personal safety.
1. Electric Shock Prevention
WARNING
• While power is on or when the inverter is running, do not open the front
cover. Otherwise you may get an electric shock.
• Do not run the inverter with the front cover removed. Otherwise, you may
access the exposed high-voltage terminals or the charging part of the
circuitry and get an electric shock.
• Even if power is off, do not remove the front cover except for wiring or periodic
inspection.You may access the charged inverter circuits and get an electric shock.
• Before wiring, inspection or switching EMC filter ON/OFF connector,
power must be switched OFF. To confirm that, LED indication of the
operation panel must be checked. (It must be OFF.) Any person who is
involved in wiring, inspection or switching EMC filter ON/OFF connector
shall wait for at least 10 minutes after the power supply has been switched
OFF and check that there are no residual voltage using a tester or the like.
The capacitor is charged with high voltage for some time after power OFF,
and it is dangerous.
• This inverter must be earthed. Earthing must conform to the requirements of
national and local safety regulations and electrical code (NEC section 250,
IEC 536 class 1 and other applicable standards).
A neutral-point earthed power supply for 400V class inverter in compliance
with EN standard must be used.
• Any person who is involved in wiring or inspection of this equipment shall
be fully competent to do the work.
• The inverter must be installed before wiring. Otherwise you may get an
electric shock or be injured.
• Setting dial and key operations must be performed with dry hands to
prevent an electric shock. Otherwise you may get an electric shock.
• Do not subject the cables to scratches, excessive stress, heavy loads or
pinching. Otherwise you may get an electric shock.
• Do not replace the cooling fan while power is on. It is dangerous to replace
the cooling fan while power is on.
• Do not touch the printed circuit board with wet hands. You may get an
electric shock.
• When measuring the main circuit capacitor capacity (Pr. 259 Main circuit
capacitor life measuring = "1"), the DC voltage is applied to the motor for 1s
at powering off. Never touch the motor terminal, etc. right after powering
off to prevent an electric shock.
2. Fire Prevention
CAUTION
• Inverter must be installed on a nonflammable wall without holes (so that
nobody touches the inverter heatsink on the rear side, etc.). Mounting it to
or near flammable material can cause a fire.
• If the inverter has become faulty, the inverter power must be switched
OFF. A continuous flow of large current could cause a fire.
• Do not connect a resistor directly to the DC terminals P/+ and N/-. Doing
so could cause a fire.
3. Injury Prevention
CAUTION
• The voltage applied to each terminal must be the ones specified in the
Instruction Manual. Otherwise burst, damage, etc. may occur.
• The cables must be connected to the correct terminals. Otherwise burst,
damage, etc. may occur.
• Polarity must be correct. Otherwise burst, damage, etc. may occur.
• While power is ON or for some time after power-OFF, do not touch the
inverter since the inverter will be extremely hot. Doing so can cause burns.
4. Additional Instructions
Also the following points must be noted to prevent an accidental failure, injury,
electric shock, etc.
(1) Transportation and installation
CAUTION
• The product must be transported in correct method that corresponds to
the weight. Failure to do so may lead to injuries.
• Do not stack the boxes containing inverters higher than the number
recommended.
• The product must be installed to the position where withstands the weight
of the product according to the information in the Instruction Manual.
• Do not install or operate the inverter if it is damaged or has parts missing.
This can result in breakdowns.
• When carrying the inverter, do not hold it by the front cover or setting dial;
it may fall off or fail.
• Do not stand or rest heavy objects on the product.
• The inverter mounting orientation must be correct.
• Foreign conductive bodies must be prevented to enter the inverter. That
includes screws and metal fragments or other flammable substance such
as oil.
• As the inverter is a precision instrument, do not drop or subject it to
impact.
• The inverter must be used under the following environment: Otherwise the
inverter may be damaged.
Environment
This section is specifically about safety matters
Do not attempt to install, operate, maintain or inspect the inverter until you
have read through this Installation Guideline and appended documents
carefully and can use the equipment correctly. Do not use the inverter until
you have a full knowledge of the equipment, safety information and
instructions. In this Installation Guideline, the safety instruction levels are
classified into "WARNING" and "CAUTION".
Incorrect handling may cause hazardous conditions,
resulting in death or severe injury.
Incorrect handling may cause hazardous conditions,
resulting in medium or slight injury, or may cause
only material damage.
Surrounding LD
air
SLD
temperature (initial setting)
Ambient humidity
Storage temperature
Atmosphere
Altitude, vibration
-10°C to +50°C (non-freezing)
-10°C to +40°C (non-freezing)
90% RH or less (non-condensing)
-20°C to +65°C *1
Indoors (free from corrosive gas, flammable
gas, oil mist, dust and dirt)
Maximum 1000m above sea level for standard
operation. After that derate by 3% for every extra
500m up to 2500m (91%) 5.9m/s2 or less at 10 to
55Hz (directions of X, Y, Z axes) *2
*1 Temperature applicable for a short time, e.g. in transit.
*2 2.9m/s2 or less for the 04320 or more.
(2) Wiring
CAUTION
• Do not install a power factor correction capacitor or surge suppressor on
the inverter output side. These devices on the inverter output side may be
overheated or burn out.
• The connection orientation of the output cables U, V, W to the motor will
affect the direction of rotation of the motor.
(3) Test operation and adjustment
CAUTION
• Before starting operation, each parameter must be confirmed and
adjusted. A failure to do so may cause some machines to make
unexpected motions.
(4) Operation
WARNING
• Any person must stay away from the equipment when the retry function is
set as it will restart suddenly after trip.
• Since pressing
•
•
•
•
key may not stop output depending on the function
setting status, separate circuit and switch that make an emergency stop
(power OFF, mechanical brake operation for emergency stop, etc.) must
be provided.
OFF status of the start signal must be confirmed before resetting the
inverter fault. Resetting inverter alarm with the start signal ON restarts the
motor suddenly.
The inverter must be used for three-phase induction motors.
Connection of any other electrical equipment to the inverter output may
damage the equipment.
Do not modify the equipment.
Do not perform parts removal which is not instructed in this manual. Doing
so may lead to fault or damage of the inverter.
A-1
CAUTION
• The electronic thermal relay function does not guarantee protection of the
motor from overheating. It is recommended to install both an external
thermal and PTC thermistor for overheat protection.
• Do not use a magnetic contactor on the inverter input for frequent starting/
stopping of the inverter.
• The effect of electromagnetic interference must be reduced by using a
noise filter or by other means. Otherwise nearby electronic equipment
may be affected.
• Appropriate measures must be taken to suppress harmonics. Otherwise
power supply harmonics from the inverter may heat/damage the power
factor correction capacitor and generator.
• When driving a 400V class motor by the inverter, the motor must be an
insulation-enhanced motor or measures must be taken to suppress surge
voltage. Surge voltage attributable to the wiring constants may occur at
the motor terminals, deteriorating the insulation of the motor.
• When parameter clear or all parameter clear is performed, the required
parameters must be set again before starting operations because all
parameters return to the initial value.
• The inverter can be easily set for high-speed operation. Before changing
its setting, the performances of the motor and machine must be fully
examined.
• Stop status cannot be hold by the inverter's brake function. In addition to
the inverter's brake function, a holding device must be installed to ensure
safety.
• Before running an inverter which had been stored for a long period,
inspection and test operation must be performed.
• For prevention of damage due to static electricity, nearby metal must be
touched before touching this product to eliminate static electricity from
your body.
(5) Emergency stop
CAUTION
• A safety backup such as an emergency brake must be provided to prevent
hazardous condition to the machine and equipment in case of inverter
failure.
• When the breaker on the inverter input side trips, the wiring must be
checked for fault (short circuit), and internal parts of the inverter for a
damage, etc. The cause of the trip must be identified and removed before
turning ON the power of the breaker.
• When any protective function is activated, appropriate corrective action
must be taken, and the inverter must be reset before resuming operation.
(6) Maintenance, inspection and parts replacement
CAUTION
• Do not carry out a megger (insulation resistance) test on the control circuit
of the inverter. It will cause a failure.
(7) Disposing of the inverter
CAUTION
• The inverter must be treated as industrial waste.
General instructions
Many of the diagrams and drawings in Instruction Manuals show the inverter
without a cover or partially open for explanation. Never operate the inverter
in this manner. The cover must be always reinstalled and the instruction in
Instruction Manuals must be followed when operating the inverter.
A-2
INSTALLATION OF THE INVERTER AND INSTRUCTIONS
1 INSTALLATION OF THE INVERTER AND INSTRUCTIONS
• Inverter Model
FR - F740 - 00126 - EC
Symbol
F740
Voltage Class
Three-phase
400V class
Symbol
Model number
00023
Displays the rated current.
to
12120
Rating plate
FR-F740-00126-EC
Inverter model
Input rating
Output rating
Capacity plate
FR-F740-00126-EC
LD (50 C) XXA
SLD (40 C) XXA
Serial number
Inverter model Serial number
Overload Current Rating
LD
SLD
Surrounding Air Temperature
120% 60s, 150% 3s
110% 60s, 120% 3s
50 C
40 C
• Installation of the inverter
Note - Some inverter models may be installed outside an
enclosure. See Appendix 2 for details.
Installation on the enclosure
00620 or less
CAUTION
When encasing multiple inverters, install them in parallel
as a cooling measure.
00770 or more
10cm or more *2
10cm or more *2
5cm or more *1
*1 1cm or more for 00083 or less
10cm or more for 01800 or more
*2 20cm or more for 01800 or more
Fix six positions for the FR-F74004320 to 08660 and fix eight positions
for the FR-F740-09620 to 12120.
• General Precaution
The bus capacitor discharge time is 10 minutes. Before starting wiring or inspection, switch power off, wait for more than 10
minutes, and check for residual voltage between terminal P/+ and N/- with a meter etc., to avoid a hazard of electrical shock.
• Environment
Before installation, check that the environment meets following specifications.
Surrounding Air
Temperature
LD: -10°C to + 50°C Maximum (non-freezing)
SLD (initial setting): -10°C to + 40°C Maximum (nonfreezing)
Measurement
position
5cm
Measurement
position
Ambient humidity
Storage temperature
Ambience
Altitude, vibration
Inverter
5cm
5cm
90%RH or less (non-condensing)
-20°C to + 65°C
Indoors (No corrosive and flammable gases, oil mist, dust and dirt.)
Below 1000m, 5.9m/s2 or less at 10 to 55Hz (directions of X, Y, Z axes) (2.9m/s2 or less for the
04320 or more)
CAUTION
•
•
•
•
Install the inverter on a strong surface securely and vertically with bolts.
Leave enough clearances and take cooling measures.
Avoid places where the inverter is subjected to direct sunlight, high temperature and high humidity.
Install the inverter on a non-combustible wall surface.
1
OUTLINE DRAWING
2 OUTLINE DRAWING
H1
H
FR-F740-09620 to
12120-EC
W1
W
W1
W1
H1
H
FR-F740-04320 to
08660-EC
H1
H
FR-F740-00023 to
03610-EC
W1
W
W1
W
W1
D
(Unit:mm)
Inverter Model
FR-F740-00023-EC
FR-F740-00038-EC
FR-F740-00052-EC
FR-F740-00083-EC
FR-F740-00126-EC
FR-F740-00170-EC
FR-F740-00250-EC
FR-F740-00310-EC
FR-F740-00380-EC
FR-F740-00470-EC
FR-F740-00620-EC
FR-F740-00770-EC
FR-F740-00930-EC
FR-F740-01160-EC
FR-F740-01800-EC
FR-F740-02160-EC
FR-F740-02600-EC
FR-F740-03250-EC
FR-F740-03610-EC
FR-F740-04320-EC
FR-F740-04810-EC
FR-F740-05470-EC
FR-F740-06100-EC
FR-F740-06830-EC
FR-F740-07700-EC
FR-F740-08660-EC
FR-F740-09620-EC
FR-F740-10940-EC
FR-F740-12120-EC
2
W
W1
150
125
H
H1
260
245
D
140
170
220
195
300
285
190
250
230
400
380
190
325
270
550
530
195
435
380
550
525
250
620
595
300
465
400
740
715
360
1010
984
380
498
200
680
300
790
315
1330
1300
995
300
1580
1550
440
3 WIRING
*1. DC reactor (FR-HEL)
Be sure to connect the DC reactor
supplied with the 01800 or more.
When a DC reactor is connected
to the 01160 or less, remove the
jumper across P1-P/+.
Source logic
Main circuit terminal
Control circuit terminal
Earth Jumper
P1
MC
MCCB
Jumper
*2. To supply power to the
control circuit separately,
remove the jumper across
R1/L11 and S1/L21.
*2
Jumper
P/+
PX*7 N/- CN8*6
U
V
W
ON EMC filter
ON/OFF
OFF connector
R/L1
S/L2
T/L3
Three-phase AC
power supply
Resistor unit
(Option)
Brake unit
(Option)
*1
R1/L11
S1/L21
PR*7
B1
STR
A1
(Refer to the Instruction
Manual (applied)
chapter4.)
C2
B2
Relay output 2
A2
JOG
Jog mode
Second function selection
RUN
RT
SU
MRS
IPF
Output stop
RES *3
Reset
OL
AU
(Common for external power supply transistor)
PC
24VDC power supply
Contact input common
*4 Voltage/current
(Common for external power supply transistor)
Frequency setting signal (Analog)
3
2
1
Auxiliary (+)
input (-)
Terminal
4 input (+)
(-)
(Current
input)
Connector
Terminal functions
vary with the output
Up to frequency terminal assignment
(Pr. 190 to Pr. 194)
Instantaneous
Refer to the
power failure
Instruction Manual
(applied) chapter4.
Overload
Frequency detection
SINK
SD
SOURCE
CS PTC
Open collector output
Running
FU
AU
Terminal 4 input selection
(Current input selection)
Selection of automatic restart
after instantaneous
power failure
Contact input common (Sink)
*5. It is recommended to use
2W1kΩ when the
frequency setting signal is
changed frequently.
Relay output
Terminal functions
vary with the output
Relay output 1 terminal assignment
(Fault output) (Pr. 195, Pr. 196)
RL
Low speed
(Refer to the
Instruction Manual
(applied) chapter4.)
Earth
STOP
RM
Middle speed
*4. Terminal input specifications
can be changed by analog
input specifications switchover
(Pr. 73, Pr. 267). Set the
voltage/current input switch in
the OFF position to select
voltage input (0 to 5V/0 to
10V) and ON to select current
input (0 to 20mA).
IM
C1
STF
RH
High speed
Frequency setting
potentiometer
1/2W1kΩ
*5
Motor
Control circuit
Start self-holding selection
*3. AU terminal can be
used as PTC input
terminal.
*7. Do not use PR and PX terminals.
Please do not remove the jumper
connected to terminal PR and PX.
Main circuit
Earth
Control input signals (No voltage input allowed)
Forward
Terminal functions vary
rotation
with the input terminal
start
assignment
Reverse
(Pr. 178 to Pr. 189)
(Refer to the Instruction
rotation
start
Manual (applied) chapter4.)
Multi-speed
selection
*6. A CN8 (for MT-BU5)
connector is provided
with the 01800 or more.
input switch
4 2
ON
10(+5V)
OFF
0 to 5VDC Initial value
2 0 to 10VDC
selected *4
0 to 20mADC
5
(Analog common)
SE
PU
connector
10E(+10V)
Initial
0 to ±10VDC value
1
0 to ±5VDC selected *4
Initial
4 to 20mADC value
4 0 to 5VDC
selected *4
0 to 10VDC
CA
AM
5
(+)
(-)
Analog current output
(0 to 20mADC)
Analog signal output
(0 to 10VDC)
RS-485 terminals
TXD+
TXD-
Data transmission
RXD+
SG
Option connector 1
(+)
(-)
RXD-
for plug-in option
connection
Open collector output common
Sink/source common
Terminating
resistor VCC
Data reception
GND
5V (Permissible load
current 100mA)
CAUTION
• To prevent a malfunction due to noise, keep the signal cables more than 10cm away from the power cables. Also separate
the main circuit wire of the input side and the output side.
• After wiring, wire offcuts must not be left in the inverter.
Wire offcuts can cause an alarm, failure or malfunction. Always keep the inverter clean.
When drilling mounting holes in a control box etc., take care not to allow chips and other foreign matter to enter the inverter.
• Set the voltage/current input switch correctly. Different setting may cause a fault, failure or malfunction.
3
WIRING
3.1 Main circuit terminal
(1) Terminal layout and wiring
400V class
FR-F740-00023 to 00126-EC
FR-F740-00170, 00250-EC
Jumper
Screw size (M4)
R/L1 S/L2 T/L3
Jumper
P/+
N/-
Charge lamp
PX
R1/L11 S1/L21
IM
Power
supply
PR
N/-
Jumper
Screw size
(M4)
P/+ PR
Jumper
R1/L11 S1/L21
Charge lamp
Screw size
(M4)
Motor
PX
R/L1 S/L2 T/L3
IM
Motor
Power supply
Screw size
(M4)
FR-F740-00310, 00380-EC
FR-F740-00470, 00620-EC
R1/L11 S1/L21
Screw size
(M4)
R1/L11 S1/L21
Screw size (M4)
Charge lamp
Jumper
Charge lamp
PR
Jumper
Screw size (M6)
Jumper
P/+
Screw size (M5)
N/-
R/L1 S/L2 T/L3
R/L1 S/L2 T/L3
N/-
IM
PR
Power supply
P/+
Jumper
Motor
IM
Screw size (M6)
Motor
Power supply
Screw size (M5)
FR-F740-00770 to 01160-EC
FR-F740-01800 to 02600-EC
R1/L11 S1/L21
Screw size(M4)
Charge lamp
R1/L11 S1/L21
Screw size (M4)
Jumper
Charge lamp
Jumper
Screw size
(00770: M6
00930/01160: M8)
Screw size
Screw size
(01800: M8, 02160/02600: M10) Screw size (M10) (01800: M8, 02160/02600: M10)
R/L1 S/L2 T/L3
R/L1 S/L2 T/L3
Power
supply
4
N/-
P/+
Jumper
Screw size
(00770: M6
00930/01160: M8)
N/-
P/+
P/+
IM
Motor
Power
supply
IM
Motor
DC reactor
Screw size
(01800: M8,
02160/02600: M10)
WIRING
FR-F740-03250 to 04810-EC
FR-F740-05470 to 12120-EC
R1/L11 S1/L21 Screw size (M4)
R1/L11 S1/L21 Screw size (M4)
Charge lamp
Charge lamp
Jumper
Jumper
Screw size
(03250/03610: M10
04320/04810: M12)
R/L1 S/L2 T/L3
N/-
P/+
Screw size (M12)
P/+
R/L1 S/L2 T/L3 N/-
P/+
Screw size
(M10)
P/+
Power supply
Screw size (M12)
(for option)
IM
P/+
Motor
DC reactor
IM
Motor
Power supply
DC reactor
Screw size (M10)
CAUTION
· The power supply cables must be connected to R/L1, S/L2, T/L3. (Phase sequence needs not to be matched.) Never
connect the power cable to the U, V, W of the inverter. Doing so will damage the inverter.
· Connect the motor to U, V, W. At this time, turning on the forward rotation switch (signal) rotates the motor in the
counterclockwise direction when viewed from the motor shaft.
· When wiring the inverter main circuit conductor of the 05470 or more, tighten a nut from the right side of the conductor.
When wiring two wires, place wires on both sides of the conductor. (Refer to the drawing below.) For wiring, use bolts (nuts)
provided with the inverter.
5
WIRING
(2) Cable size
Select the recommended cable size to ensure that a voltage drop will be 2% max.
If the wiring distance is long between the inverter and motor, a main circuit cable voltage drop will cause the motor
torque to decrease especially at the output of a low frequency.
The following table indicates a selection example for the wiring length of 20m.
400V class (when input power supply is 440V based on the rated current for 110% overload for 1 minute)
Applicable Inverter
Model
FR-F740-00023 to
00083-EC
FR-F740-00126-EC
FR-F740-00170-EC
FR-F740-00250-EC
FR-F740-00310-EC
FR-F740-00380-EC
FR-F740-00470-EC
FR-F740-00620-EC
FR-F740-00770-EC
FR-F740-00930-EC
FR-F740-01160-EC
FR-F740-01800-EC
FR-F740-02160-EC
FR-F740-02600-EC
FR-F740-03250-EC
FR-F740-03610-EC
FR-F740-04320-EC
FR-F740-04810-EC
FR-F740-05470-EC
FR-F740-06100-EC
FR-F740-06830-EC
FR-F740-07700-EC
FR-F740-08660-EC
FR-F740-09620-EC
FR-F740-10940-EC
FR-F740-12120-EC
*1
*2
*3
*4
Terminal
Tightening
Screw Size
Torque N·m
*4
Crimping
(Compression)
Terminal
R/L1,
U, V,
S/L2,
W
T/L3
Cable Sizes
HIV, etc. (mm2) *1
R/L1,
S/L2,
T/L3
U, V,
W
cable
AWG/MCM *2
R/L1,
S/L2,
T/L3
U, V, W
PVC, etc. (mm2) *3
R/L1,
S/L2,
T/L3
U, V, W
cable
M4
1.5
2-4
2-4
2
2
2
14
14
2.5
2.5
2.5
M4
M4
M4
M5
M5
M6
M6
M6
M8
M8
M8
M10
M10
M10
M10
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
M12(M10)
1.5
1.5
1.5
2.5
2.5
4.4
4.4
4.4
7.8
7.8
7.8
14.7
14.7
14.7
14.7
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
24.5
2-4
5.5-4
5.5-4
8-5
14-5
14-6
22-6
22-6
38-8
60-8
60-8
100-10
100-10
150-10
150-10
100-12
100-12
150-12
150-12
200-12
C2-200
C2-250
C2-250
C2-200
C2-200
2-4
5.5-4
5.5-4
8-5
8-5
14-6
22-6
22-6
38-8
60-8
60-8
100-10
100-10
150-10
150-10
100-12
100-12
150-12
150-12
200-12
C2-200
C2-250
C2-250
C2-200
C2-200
2
3.5
5.5
8
14
14
22
22
38
60
60
80
100
125
150
2×100
2×100
2×125
2×150
2×200
2×200
2×250
2×250
3×200
3×200
2
3.5
5.5
8
8
14
22
22
38
60
60
80
100
125
150
2×100
2×100
2×125
2×150
2×200
2×200
2×250
2×250
3×200
3×200
3.5
3.5
8
8
14
14
14
14
22
22
38
38
38
38
38
38
38
38
38
60
60
60
100
100
100
12
12
10
8
6
6
4
4
1
1/0
1/0
3/0
4/0
250
300
2×4/0
2×4/0
2×250
2×300
2×350
2×400
2×500
2×500
3×350
3×400
14
12
10
8
8
6
4
4
2
1/0
1/0
3/0
4/0
250
300
2×4/0
2×4/0
2×250
2×300
2×350
2×400
2×500
2×500
3×350
3×400
2.5
4
6
10
16
16
25
25
50
50
50
70
95
120
150
2×95
2×95
2×120
2×150
2×185
2×185
2×240
2×240
3×185
3×185
2.5
4
6
10
10
16
25
25
50
50
50
70
95
120
150
2×95
2×95
2×120
2×150
2×185
2×185
2×240
2×240
3×185
3×185
4
4
10
10
16
16
16
16
25
25
25
35
50
70
95
95
95
120
150
2×95
2×95
2×120
2×120
2×150
2×150
For the 01160 or less, the recommended cable size is that of the cable (e.g. HIV cable (600V class 2 vinyl-insulated cable)) with continuous
maximum permissible temperature of 75°C. Assumes that the ambient temperature is 50°C or less and the wiring distance is 20m or less.
For the 01800 or more, the recommended cable size is that of the cable (e.g. LMFC (heat resistant flexible cross-linked polyethylene insulated
cable)) with continuous maximum permissible temperature of 90°C. Assumes that the ambient temperature is 50°C or less and wiring is performed
in an enclosure.
For the 00930 or less, the recommended cable size is that of the cable (THHW cable) with continuous maximum permissible temperature of 75°C.
Assumes that the ambient temperature is 40°C or less and the wiring distance is 20m or less.
For the 01160 or more, the recommended cable size is that of the cable (THHN cable) with continuous maximum permissible temperature of 90°C.
Assumes that the ambient temperature is 40°C or less and wiring is performed in an enclosure.
(Selection example for use mainly in the United States.)
For the 00930 or less, the recommended cable size is that of the cable (PVC cable) with continuous maximum permissible temperature of 70°C.
Assumes that the ambient temperature is 40°C or less and the wiring distance is 20m or less.
For the 01160 or more, the recommended cable size is that of the cable (XLPE cable) with continuous maximum permissible temperature of 90°C.
Assumes that the ambient temperature is 40°C or less and wiring is performed in an enclosure.
(Selection example for use mainly in the Europe.)
The terminal screw size indicates the terminal size for R/L1, S/L2, T/L3, U, V, W, and a screw for earthing.
A screw for earthing (grounding) of the FR-F740-04320 or more is indicated in ( ).
The line voltage drop can be calculated by the following formula:
line voltage drop [V]=
3 × wire resistance[mΩ/m] × wiring distance[m] × current[A]
1000
Use a larger diameter cable when the wiring distance is long or when it is desired to decrease the voltage drop
(torque reduction) in the low speed range.
CAUTION
· Tighten the terminal screw to the specified torque.
A screw that has been tighten too loosely can cause a short circuit or malfunction.
A screw that has been tighten too tightly can cause a short circuit or malfunction due to the unit breakage.
· Use crimping terminals with insulation sleeve to wire the power supply and motor.
6
WIRING
(3) Total wiring length
The overall wiring length for connection of a single motor or multiple motors should be
within the value in the table below.
Pr. 72 PWM frequency selection setting
(carrier frequency)
2 (2kHz) or less
3 (3kHz), 4 (4kHz)
5 (5kHz) to 9 (9kHz)
10 (10kHz) or more
00023
00038
300m
200m
500m
300m
100m
50m
00052 or more
500m
500m
When driving a 400V class motor by the inverter, surge voltages attributable to the wiring constants may occur at
the motor terminals, deteriorating the insulation of the motor. Take the following measures in this case.
Connect the surge voltage suppression filter (FR-ASF-H) to the 01160 or less and the sine wave filter (MT-BSL/
BSC) to the 01800 or more on the inverter output side.
CAUTION
· Especially for long-distance wiring, the inverter may be affected by a charging current caused by the stray capacitances of the wiring,
leading to a malfunction of the overcurrent protective function or fast response current limit function or a malfunction or fault of the
equipment connected on the inverter output side. If fast-response current limit function malfunctions, disable this function. (For Pr.156
Stall prevention operation selection, refer to the Instruction Manual (applied).)
· For details of Pr. 72 PWM frequency selection ,refer to the Instruction Manual (applied). When using an optional sine wave filter (MT-BSL/
BSC) for the 01800 or more, set “25” in Pr.72 (2.5kHz).
For explanation of surge voltage suppression filter (FR-ASF-H) and sine wave filter (MT-BSL/BSC), refer to the manual of each option.
(4) Cable size of the control circuit power supply (terminal R1/L11, S1/L21)
· Terminal screw size: M4
· Cable size: 0.75mm2 to 2mm2
· Tightening torque: 1.5N·m
3.2 Control circuit terminals
(1) Terminal layout
· Terminal Screw Size: M3.5
· Tightening torque: 1.2N·m
CA
A1
B1
C1
PC AM 10E 10
A2
B2
2
C2
5
RL
4
RM RH
1
RT
SD
PC
AU STOP RES STF STR PC
SE RUN SU IPF OL
FU MRS JOG CS
(2) Instructions for wiring of the control circuit terminal
1)
2)
3)
4)
Terminals 5, PC and SE are common to the I/O signals and isolated from each other. Do not earth.
It is recommended to use the cables of 0.75mm2 gauge for connection to the control circuit terminals.
If the cable gauge used is 1.25mm2 or more, the front cover may be lifted when there are many cables running
or the cables are run improperly, resulting in an operation panel contact fault.
The wiring length should be 30m maximum.
Use two or more parallel micro-signal contacts or twin contacts to
prevent a contact faults when using contact inputs since the
control circuit input signals are micro-currents.
Micro signal contacts
5)
6)
7)
Twin contacts
Use shielded or twisted cables for connection to the control circuit terminals and run them away from the main
and power circuits (including the 200V relay sequence circuit).
Do not apply a voltage to the contact input terminals (e.g. STF) of the control circuit.
Always apply a voltage to the fault output terminals (A, B, C) via a relay coil, lamp, etc.
7
PRECAUTIONS FOR USE OF THE INVERTER
4 PRECAUTIONS FOR USE OF THE INVERTER
The FR-F700 series is a highly reliable product, but incorrect peripheral circuit making or operation/handling method
may shorten the product life or damage the product. Before starting operation, always recheck the following items.
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(8)
(9)
(10)
(11)
(12)
(13)
(14)
(15)
(16)
8
Use crimping terminals with insulation sleeve to wire the power supply and motor.
Application of power to the output terminals (U, V, W) of the inverter will damage the inverter. Never perform such wiring.
After wiring, wire offcuts must not be left in the inverter.
Wire offcuts can cause an alarm, failure or malfunction. Always keep the inverter clean. When drilling mounting holes in
an enclosure etc., take care not to allow chips and other foreign matter to enter the inverter.
Use cables of the size to make a voltage drop 2% maximum.
If the wiring distance is long between the inverter and motor, a main circuit cable voltage drop will cause the motor torque
to decrease especially at the output of a low frequency. Refer to page 6 for the recommended cable sizes.
The overall wiring length should be 500m maximum.
Especially for long distance wiring, the fast response current limit function may decrease or the equipment connected to the
secondary side may malfunction or become faulty under the influence of a charging current due to the stray capacity of the
wiring. Therefore, note the overall wiring length. (Refer to page 7.)
Electromagnetic wave interference
The input/output (main circuit) of the inverter includes high frequency components, which may interfere with the
communication devices (such as AM radios) used near the inverter. An EMC filter can minimize noise interference.
Do not install a power factor correction capacitor, surge suppressor or radio noise filter on the inverter output side.
This will cause the inverter to trip or the capacitor, varistor, or arrester to be damaged. If any of the above devices is
installed, immediately remove it.
For some short time after the power is switched off, a high voltage remains in the smoothing capacitor. When accessing the
inverter for inspection, wait for at least 10 minutes after the power supply has been switched off, and then make sure that
the voltage across the main circuit terminals P/+-N/- of the inverter is not more than 30VDC using a tester, etc.
A short circuit or earth fault on the inverter output side may damage the inverter modules.
· Fully check the insulation resistance of the circuit prior to inverter operation since repeated short circuits caused by
peripheral circuit inadequacy or an earth fault caused by wiring inadequacy or reduced motor insulation resistance
may damage the inverter modules.
· Fully check the to-earth insulation and phase to phase insulation of the inverter output side before power-on.
Especially for an old motor or use in hostile atmosphere, securely check the motor insulation resistance etc.
Do not use the inverter input side magnetic contactor to start/stop the inverter.
Always use the start signal (ON/OFF of STF and STR signals) to start/stop the inverter.
Do not apply a voltage higher than the permissible voltage to the inverter I/O signal circuits.
Application of permissible voltage to the inverter I/O signal circuit and incorrect polarity may damage the I/O terminal.
Especially check the wiring to prevent the speed setting potentiometer from being connected incorrectly to short
terminals 10E-5.
Provide electrical and mechanical interlocks for MC1 and MC2
MC1
which are used for bypass operation.
Interlock
When the wiring is incorrect and if there is a bypass operation
Power
R/L1 U
IM
circuit as shown right, the inverter will be damaged when the
supply
S/L2 V
MC2
power supply is connected to the inverter U, V, W terminals, due
T/L3 W Undesirable current
to arcs generated at the time of switch-over or chattering caused
Inverter
by a sequence error.
If the machine must not be restarted when power is restored
after a power failure, provide a magnetic contactor in the inverter's input side and also make up a sequence which will
not switch on the start signal.
If the start signal (start switch) remains on after a power failure, the inverter will automatically restart as soon as the
power is restored.
Instructions for overload operation
When performing operation of frequent start/stop of the inverter, increase/decrease in the temperature of the transistor
element of the inverter may repeat due to a continuous flow of large current, shortening the life from thermal fatigue.
Since thermal fatigue is related to the amount of current, the life can be increased by reducing bound current, starting
current, etc. Decreasing current may increase the life. However, decreasing current will result in insufficient torque and
the inverter may not start. Therefore, increase the inverter capacity to have enough allowance for current.
Make sure that the specifications and rating match the system requirements.
If electromagnetic noise generated from the inverter causes frequency setting signal to fluctuate and motor rotation
speed to be unstable when changing motor speed with analog signal, the following countermeasures are effective.
· Do not run the signal cables and power cables (inverter I/O cables) in parallel with each other and do not bundle them.
· Run signal cables as far away as possible from power cables (inverter I/O cables).
· Use shield cables as signal cables.
· Install a ferrite core on the signal cable (Example: ZCAT3035-1330 TDK).
FAILSAFE OF THE SYSTEM WHICH
USES THE INVERTER
5 FAILSAFE OF THE SYSTEM WHICH USES THE INVERTER
When a fault occurs, the inverter trips to output a fault signal. However, a fault output signal may not be output at an
inverter fault occurrence when the detection circuit or output circuit fails, etc. Although we assure best quality products,
provide an interlock which uses inverter status output signals to prevent accidents such as damage to machine when
the inverter fails for some reason and at the same time consider the system configuration where failsafe from outside
the inverter, without using the inverter, is enabled even if the inverter fails.
(1) Interlock method which uses the inverter status output signals
By combining the inverter status output signals to provide an interlock as shown below, an inverter alarm can be
detected.
No
Interlock Method
Check Method
Used Signals
1)
Inverter protective
function operation
Operation check of an alarm contact
Circuit error detection by negative logic
Fault output signal
(ALM signal)
2)
Inverter running status
Operation ready signal check
Operation ready signal
(RY signal)
3)
Inverter running status
Logic check of the start signal and
running signal
4)
Inverter running status
Logic check of the start signal and
output current
Start signal
(STF signal, STR signal)
Running signal (RUN signal)
Start signal
(STF signal, STR signal)
Output current detection signal
(Y12 signal)
Refer to Page
Refer to the chapter
4 of the Instruction
Manual.
Refer to the chapter
4 of the Instruction
Manual.
Refer to the chapter
4 of the Instruction
Manual.
Refer to the chapter
4 of the Instruction
Manual.
(2) Backup method outside the inverter
Even if the interlock is provided by the inverter status signal, enough failsafe is not ensured depending on the
failure status of the inverter itself. For example, when the inverter CPU fails, even if the interlock is provided using
the inverter fault signal, start signal and RUN signal, there is a case where a fault signal is not output and RUN
signal is kept output even if an inverter fault occurs.
Provide a speed detector to detect the motor speed and current detector to detect the motor current and consider
the backup system such as checking up as below according to the level of importance of the system.
1) Start signal and actual operation check
Check the motor running and motor current while the start signal is input to the inverter by comparing the start signal to
the inverter and detected speed of the speed detector or detected current of the current detector. Note that the motor
current runs as the motor is running for the period until the motor stops since the inverter starts decelerating even if the
start signal turns off. For the logic check, configure a sequence considering the inverter deceleration time. In addition, it is
recommended to check the three-phase current when using the current detector.
2) Command speed and actual operation check
Check if there is no gap between the actual speed and commanded speed by comparing the inverter speed command
and detected speed of the speed detector.
Controller
System failure
Inverter
Sensor
(speed, temperature,
air volume, etc.)
To the alarm detection sensor
9
PARAMETER LIST
6 PARAMETER LIST
6.1 Parameter list
In the initial setting, only the simple mode parameters are displayed.
Set Pr. 160 User group read selection as required.
Parameter
Initial
Value
Name
Setting
Range
9999
160
User group read selection
0
9999
1
Remarks
Only the simple mode parameters can be displayed.
Simple mode and extended mode parameters can be
displayed.
Only the parameters registered in the user group can be
displayed.
REMARKS
⋅ The parameters marked  are the simple mode parameters.
⋅ The parameters marked with
in the table allow its setting to be changed during operation even if "0" (initial value)
is set in Pr. 77 Parameter write selection.
Parameters
Name
Setting
Range
Initial
Value
0
Torque boost
0 to 30%
1
Maximum frequency
0 to 120Hz
6/4/3/2/
1.5/1% *2
120/60Hz
2
3
Minimum frequency
0 to 120Hz
0Hz
Base frequency
0 to 400Hz
50Hz
4
Multi-speed setting
(high speed)
Multi-speed setting
(middle speed)
Multi-speed setting
(low speed)
0 to 400Hz
50Hz
0 to 400Hz
30Hz
5
6
0 to 400Hz
*1
10Hz
Parameters
20
21
22
23
Multi-speed setting
Acceleration time
0 to 3600/360s
5s/15s *3
Deceleration time
0 to 3600/360s
10s/30s *3
28
9
Electronic thermal
O/L relay
0 to 500/
0 to 3600A *1
Rated
inverter
current
29
10
DC injection brake
operation frequency
0 to 120Hz,
9999
3Hz
11
DC injection brake
operation time
DC injection brake
operation voltage
0 to 10s, 8888
0.5s
12
10
Multi-speed input
compensation
selection
Acceleration/
deceleration pattern
selection
30
Regenerative
function selection
31
Frequency jump 1A
32
Frequency jump 1B
33
Frequency jump 2A
0 to 30%
4/2/1% *4
13
Starting frequency
0 to 60Hz
0.5Hz
14
Load pattern
selection
0, 1
15
Jog frequency
0 to 400Hz
5Hz
16
Jog acceleration/
deceleration time
0 to 3600/360s
0.5s
34
Frequency jump 2B
17
MRS input selection
0, 2
0
35
Frequency jump 3A
18
High speed
120 to 400Hz
maximum frequency
0 to 1000V,
Base frequency
voltage
8888, 9999
36
Frequency jump 3B
19
*1
*2
*3
*4
Acceleration/
deceleration
reference frequency
Acceleration/
deceleration time
increments
Stall prevention
operation level
Stall prevention
operation level
compensation factor
at double speed
24 to 27 4 speed to 7 speed
7
8
1
120/60Hz
*1
8888
Setting
Range
Initial
Value
1 to 400Hz
50Hz
Name
0, 1
0
0 to 120%, 9999
110%
0 to 150%, 9999
9999
0 to 400Hz,
9999
9999
0, 1
0
0, 1, 2, 3, 6
0
0, 2, 10, 20/
0, 1, 2, 10, 11,
20, 21 *1
0 to 400Hz,
9999
0 to 400Hz,
9999
0 to 400Hz,
9999
0 to 400Hz,
9999
0 to 400Hz,
9999
0 to 400Hz,
9999
The setting depends on capacities. (01160 or less/01800 or more)
The setting depends on capacities. (00023/00038 to 00083/00126, 00170/00250 to 00770/00930, 01160/01800 or more)
The setting depends on capacities. (00170 or less/00250 or more)
The setting depends on capacities. (00170 or less/00250 to 01160/01800 or more)
0
9999
9999
9999
9999
9999
9999
PARAMETER LIST
Parameters
37
Speed display
41
Up-to-frequency
sensitivity
Output frequency
detection
Output frequency
detection for
reverse rotation
Second acceleration/
deceleration time
42
43
44
Setting
Range
Name
Initial
Value
Parameters
Name
0
70
Special regenerative
brake duty *3
0 to 10%
0%
10%
71
Applied motor
0, 1, 2, 20
0
0 to 400Hz
6Hz
72
PWM frequency
selection
0 to 15/
0 to 6, 25 *1
2
73
Analog input selection
0 to 7, 10 to 17
1
74
Input filter time
constant
Reset selection/
disconnected PU
detection/PU stop
selection
Fault code output
selection
Parameter write
selection
Reverse rotation
prevention selection
Operation mode
selection
0 to 8
1
0 to 3, 14 to 17,
100 to 103,
114 to 117 *4
14
0, 1, 2
0
0, 1, 2
0
0, 1, 2
0
0, 1, 2, 3, 4, 6, 7
0
0 to 400Hz,
9999
0 to 3600/360s
9999
5s
Second deceleration
time
0 to 3600/
360s, 9999
9999
46
Second torque boost
0 to 30%, 9999
9999
47
Second V/F
(base frequency)
0 to 400Hz,
9999
9999
0 to 120%
110%
49
50
Second stall
prevention
operation current
Second stall
prevention
operation frequency
Second output
frequency detection
51
Second electronic
thermal O/L relay
52
DU/PU main display
data selection
54
CA terminal
function selection
0 to 400Hz,
9999
0Hz
0 to 400Hz
30Hz
0 to 500A,
9999/
0 to 3600A,
9999 *1
0, 5, 6, 8 to 14,
17, 20, 23 to 25,
50 to 57, 100 *2
1 to 3, 5, 6,
8 to 14, 17, 21,
24, 50, 52, 53
76
77
78
 79
80
0
90
100
101
1
102
103
55
Frequency
monitoring reference
0 to 400Hz
56
Current monitoring
reference
0 to 500A/
0 to 3600A *1
57
0, 0.1 to 5s,
9999/
Restart coasting time
0, 0.1 to 30s,
9999 *1
58
Restart cushion time
0 to 60s
1s
59
Remote function
selection
0, 1, 2, 3, 11,
12, 13
0
Energy saving
control selection
0, 4, 9
0
65
Retry selection
0 to 5
0
117
66
Stall prevention
operation reduction
starting frequency
0 to 400Hz
50Hz
118
Number of retries at
fault occurrence
0, 1 to 10,
101 to 110
0
68
Retry waiting time
0 to 10s
1s
69
Retry count display
erase
0
0
67
*1
*2
*3
*4
75
9999
*2
 60
Initial
Value
0 to 100%
0, 1 to 9998
45
48
Setting
Range
50Hz
Rated
inverter
current
9999
104
105
106
107
108
109
119
120
121
0.4 to 55kW,
Motor
9999/
capacity(Simple
magnetic flux vector 0 to 3600kW,
control)
9999 *1
0 to 50Ω, 9999/
Motor constant (R1) 0 to 400mΩ,
9999 *1
0 to 400Hz,
V/F1 (first frequency)
9999
V/F1 (first frequency
0 to 1000V
voltage)
0 to 400Hz,
V/F2
(second frequency) 9999
V/F2 (second
0 to 1000V
frequency voltage)
0 to 400Hz,
V/F3 (third frequency)
9999
V/F3 (third
0 to 1000V
frequency voltage)
0 to 400Hz,
V/F4
(fourth frequency)
9999
V/F4 (fourth
0 to 1000V
frequency voltage)
0 to 400Hz,
V/F5 (fifth frequency)
9999
V/F5 (fifth frequency
0 to 1000V
voltage)
PU communication
0 to 31
station
PU communication
48, 96, 192, 384
speed
PU communication
stop bit length.
PU communication
parity check
Number of PU
communication
retries
9999
9999
9999
0V
9999
0V
9999
0V
9999
0V
9999
0V
0
192
0, 1, 10, 11
1
0, 1, 2
2
0 to 10, 9999
1
The setting depends on capacities. (01160 or less/01800 or more)
Setting of "9" can be made for the 01800 or more.
Setting can be made for the 01800 or more.
Setting of "100 to 103", "114 to 117" can be made for the 01800 or more.
11
PARAMETER LIST
Parameters
Name
122
PU communication
check time interval
123
PU communication
waiting time setting
124
PU communication
CR/LF selection
Terminal 2
frequency setting
gain frequency
Terminal 4
frequency setting
gain frequency
 125
 126
127
128
PID control automatic
switchover frequency
PID action selection
129
PID proportional
band
130
PID integral time
131
PID upper limit
132
PID lower limit
133
PID action set point
134
PID differential time
135
Electronic bypass
sequence selection
MC switchover
interlock time
Waiting time at a
start
Bypass selection at
a fault
Automatic
switchover
frequency from
inverter to bypass
operation
Backlash
acceleration
stopping frequency
Backlash
acceleration
stopping time
Backlash
deceleration
stopping frequency
Backlash
deceleration
stopping time
136
137
138
139
140
141
142
143
144
Speed setting
switchover
145
PU display language
selection
Stall prevention
level at 0V input.
Stall prevention
level at 10V input.
148
149
*1
12
Setting
Range
0, 0.1 to 999.8s,
9999
0 to 150ms,
9999
0, 1, 2
Initial
Value
Parameters
Name
9999
150
9999
151
Output current
detection level
Output current
detection signal
delay time
Zero current
detection level
Zero current
detection time
Voltage reduction
selection during
stall prevention
operation
RT signal reflection
time selection
1
152
0 to 400Hz
50Hz
153
0 to 400Hz
50Hz
154
0 to 400Hz,
9999
10, 11, 20, 21,
50, 51, 60, 61,
110, 111, 120,
121
0.1 to 1000%,
9999
0.1 to 3600s,
9999
0 to 100%,
9999
0 to 100%,
9999
0 to 100%,
9999
0.01 to 10.00s,
9999
9999
10
155
0 to 60Hz,
9999
0, 1
1
0 to 25s, 9999
0s
AM terminal
function selection
1 to 3, 5, 6,
8 to 14, 17, 21,
24, 50, 52, 53 *1
1
159
161
0
0.5s
157
162
0, 1
0 to 10s
0
9999
0.5s
5%
OL signal output
timer
160
0 to 100s
0 to 150%
156
9999
1s
0s
0
9999
0 to 100s
0 to 10s
0 to 31, 100,
101
158
0
163
164
165
9999
166
Automatic
switchover
frequency range
from bypass to
inverter operation
User group read
selection
Frequency setting/
key lock operation
selection
Automatic restart after
instantaneous power
failure selection
First cushion time
for restart
First cushion
voltage for restart
Stall prevention
operation level for
restart
Output current
detection signal
retention time
Output current
detection operation
selection
0 to 10Hz,
9999
9999
0, 1, 9999
9999
0, 1, 10, 11
0
0, 1, 10, 11
0
0 to 20s
0s
0 to 100%
0%
0 to 120%
110%
0 to 10s, 9999
0.1s
0 to 400Hz
1Hz
0 to 360s
0.5s
168
169
Parameter for manufacturer setting.
Do not set.
0 to 400Hz
1Hz
170
0 to 360s
0.5s
Cumulative power
meter clear
Operation hour
meter clear
User group
registered display/
batch clear
User group
registration
167
171
172
0, 2, 4, 6, 8,
10, 102, 104,
106, 108, 110
4
0 to 7
1
0 to 120%
110%
0 to 120%
120%
Setting of "9" can be made for the 01800 or more.
110%
0, 10
1s
0, 1
0 to 120%
Initial
Value
Stall prevention
operation selection
100%
9999
Setting
Range
173
174
178
0, 1, 10, 11
0
0, 10, 9999
9999
0, 9999
9999
9999, (0 to 16)
0
0 to 999, 9999
9999
User group clear
0 to 999, 9999
9999
STF terminal
function selection
0 to 8, 10 to 12,
14, 16, 24, 25,
37, 60, 62, 64 to
67, 70 to 72,
9999
60
PARAMETER LIST
Parameters
Setting
Range
0 to 8, 10 to 12,
14, 16, 24, 25,
37, 61, 62, 64 to
67, 70 to 72,
9999
179
STR terminal
function selection
180
RL terminal function
selection
RM terminal
function selection
RH terminal
function selection
RT terminal function
selection
0 to 8, 10 to 14,
16, 24, 25, 37,
62, 64 to 67, 70
to 72, 9999
184
AU terminal
function selection
0 to 8, 10 to 14,
16, 24, 25, 37,
62 to 67, 70 to
72, 9999
185
JOG terminal
function selection
CS terminal function
selection
MRS terminal
function selection
STOP terminal
function selection
RES terminal
function selection
181
182
183
186
187
188
189
190
RUN terminal
function selection
191
SU terminal function
selection
192
IPF terminal
function selection
193
OL terminal function
selection
194
FU terminal function
selection
195
196
232
to
239
240
241
*1
Name
ABC1 terminal
function selection
ABC2 terminal
function selection
Multi-speed setting
(speeds 8 to 15)
Soft-PWM operation
selection
Analog input
display unit
switchover
Initial
Value
Parameters
242
61
243
0
1
2
244
Rated slip
246
Slip compensation
time constant
Constant-power
range slip
compensation
selection
247
4
0 to 5, 7, 8, 10
to 19, 25, 26,
45 to 48, 64, 70
to 79, 85, 90,
91, 94 to 96,
98, 99,100 to
105, 107, 108,
110 to 116,
125, 126, 145
to 148, 164,
170, 179, 185,
190, 191, 194
to 196,198,
199, 9999 *1
0 to 400Hz,
9999
Setting
Range
Initial
Value
0 to 100%
100%
0 to 100%
75%
0, 1
1
0 to 50%,
9999
9999
0.01 to 10s
0.5s
0, 9999
9999
9999
250
Stop selection
0 to 100s,
1000 to 1100s,
8888, 9999
251
Output phase loss
protection selection
0, 1
24
252
253
Override bias
0 to 200%
50%
Override gain
0 to 200%
150%
25
255
62
256
0
257
Life alarm status
display
Inrush current limit
circuit life display
Control circuit
capacitor life
display
Main circuit
capacitor life
display
Main circuit
capacitor life
measuring
PWM frequency
automatic
switchover
Power failure stop
selection
Subtracted
frequency at
deceleration start
5
0 to 5, 7, 8,
10 to 19, 25, 26,
45 to 48, 64,
70 to 79, 85, 90
to 96, 98, 99,
100 to 105, 107,
108, 110 to 116,
125, 126,
145 to 148, 164,
170, 179, 185,
190 to 196, 198,
199, 9999 *1
Terminal 1 added
compensation
amount (terminal 2)
Terminal 1 added
compensation
amount (terminal 4)
Cooling fan
operation selection
245
3
0 to 8, 10 to 14,
16, 24, 25, 37,
62, 64 to 67, 70
to 72, 9999
Name
6
1
2
258
259
3
260
4
261
262
99
0
(0 to 100%)
100%
(0 to 100%)
100%
(0 to 100%)
100%
0, 1
0
0, 1
1
0, 1, 2, 21, 22
0
0 to 20Hz
3Hz
50Hz
263
Subtraction starting
frequency
0 to 120Hz,
9999
264
Power-failure
deceleration time 1
0 to 3600/ 360s
5s
265
Power-failure
deceleration time 2
0 to 3600/ 360s,
9999
9999
9999
266
9999
(0 to 15)
1
267
268
0, 1
1
269
0, 1
0
299
Power failure
deceleration time
0 to 400Hz
switchover
frequency
Terminal 4 input
0, 1, 2
selection
Monitor decimal
0, 1, 9999
digits selection
Parameter for manufacturer setting.
Do not set.
Rotation direction
detection selection
0, 1, 9999
at restarting
50Hz
0
9999
9999
Setting of "7, 107" can be made for the 01800 or more.
13
PARAMETER LIST
Parameters
Setting
Range
Name
Initial
Value
Parameters
331
RS-485
communication
station
0 to 31
(0 to 247)
0
557
332
RS-485
communication speed
3, 6, 12, 24,
48, 96, 192, 384
96
563
0, 1, 10, 11
1
564
0, 1, 2
2
0 to 10, 9999
1
333
334
335
336
337
338
339
340
341
342
343
495
RS-485
communication stop
bit length
RS-485
communication parity
check selection
RS-485
communication
number of retries
RS-485
communication
check time interval
RS-485
communication
waiting time setting
Communication
operation command
source
Communication
speed command
source
Communication
startup mode
selection
RS-485
communication
CR/LF selection
Communication
EEPROM write
selection
Communication
error count
Remote output
selection
570
0 to 999.8s,
9999
0s
0 to 150ms,
9999
9999
0, 1
0
0, 1, 2
0
0
522
Output stop
frequency
539
Modbus-RTU
communication
check time interval
0 to 999.8s,
9999
549
Protocol selection
0, 1
550
551
553
PID deviation limit
554
PID signal operation
selection
Current average
time
Data output mask
time
555
556
*1
14
1s
576
Output interruption
detection level
Output interruption
cancel level
Auxiliary motor
operation selection
Motor switchover
selection
MC switching
interlock time
0 to 400Hz
0Hz
577
578
580
581
586
0 to 9998,
9999
0 to 400Hz,
9999
NET mode operation
command source
selection
PU mode operation
command source
selection
575
585
0 (1 to 9998)
0, 1, 9999
1, 2
0 to 100.0%,
9999
584
587
0
588
9999
589
9999
590
9999
591
0
592
9999
593
2
594
9999
0 to 3, 10 to 13
0
0.1 to 1.0s
1s
0.0 to 20.0s
0s
The setting depends on capacities. (01160 or less/01800 or more)
0
9999
0
Maintenance timer
alarm output set time
0, 1
0 to 3600s,
9999
0, 1, 10, 11
Maintenance timer
0
1,9999
0
504
(0 to 65535)
Output interruption
detection time
⎯
0
0
573
0
Remote output data 2 0 to 4095
(0 to 65535)
9999
0, 1
0
Rated
inverter
current
4mA input check
selection
583
Remote output data 1 0 to 4095
0 to 500A/
0 to 3600A *1
571
1
496
497
503
Initial
Value
0.0 to 10.0s,
9999
582
0, 1, 2
Current average
value monitor signal
output reference
current
Energization time
carrying-over times
Operating time
carrying-over times
Multiple rating
setting
Setting
Range
Holding time at a
start
579
0, 1, 2, 10, 12
Name
595
596
597
900 to 1100%
0 to 3
1000%
0
0 to 3
0
0 to 100s
1s
Start waiting time
0 to 100s
1s
Auxiliary motor
connection-time
deceleration time
Auxiliary motor
disconnection-time
acceleration time
Auxiliary motor 1
starting frequency
Auxiliary motor 2
starting frequency
Auxiliary motor 3
starting frequency
Auxiliary motor 1
stopping frequency
Auxiliary motor 2
stopping frequency
Auxiliary motor 3
stopping frequency
Auxiliary motor start
detection time
Auxiliary motor stop
detection time
Traverse function
selection
Maximum amplitude
amount
Amplitude
compensation
amount during
deceleration
Amplitude
compensation
amount during
acceleration
Amplitude
acceleration time
Amplitude
deceleration time
0 to 3600/360s,
9999
1s
0 to 3600/360s,
9999
1s
0 to 400Hz
50Hz
0 to 400Hz
50Hz
0 to 400Hz
50Hz
0 to 400Hz
0Hz
0 to 400Hz
0Hz
0 to 400Hz
0Hz
0 to 3600s
5s
0 to 3600s
5s
0, 1, 2
0
0 to 25%
10%
0 to 50%
10%
0 to 50%
10%
0.1 to 3600s
5s
0.1 to 3600s
5s
PARAMETER LIST
Initial
Value
Parameters
0 to 3600s,
9999
5/15s *1
C2
(902)
0 to 200%
0
0 to 120Hz
20Hz
C3
(902)
Pulse increment
setting for output
power
0.1kWh,
1kWh, 10kWh,
100kWh,
1000kWh
1kWh
125
(903)
867
869
AM output filter
0 to 5s
0.01s
C4
(903)
Current output filter
0 to 5s
0.02s
872
Input phase loss
protection selection
Regeneration
avoidance operation
selection
Regeneration
avoidance operation
level
Regeneration
avoidance at
deceleration
detection sensitivity
Regeneration
avoidance
compensation
frequency limit value
Regeneration
avoidance voltage
gain
Parameters
Name
611
Acceleration time at
a restart
653
Speed smoothing
control
Speed smoothing
cutoff frequency
654
799
882
883
884
885
886
0 to 300%
100%
0 to 400Hz
0Hz
0 to 300%
20%
0 to 400Hz
50Hz
0 to 300%
100%
Current output bias
signal
0 to 100%
0%
Current output bias
current
0 to 100%
0%
Current output gain
signal
0 to 100%
100%
Current output gain
current
0 to 100%
100%
PID display bias
coefficient
0 to 500.00,
9999
9999
PID display bias
analog value
0 to 300.0%
20%
PID display gain
coefficient
0 to 500.00,
9999
9999
PID display gain
analog value
0 to 300.0%
100%
989
Parameter copy
alarm release
10/100 *1
990
PU buzzer control
0, 1
1
0 to 63
58
0, 1
0
0, 1
0
760VDC/
785VDC
126
(905)
0
0 to 10Hz,
9999
6Hz
0 to 200%
100%
9999
889
Free parameter 2
0 to 9999
9999
891
Cumulative power
monitor digit shifted
times
0 to 4, 9999
9999
892
Load factor
30 to 150%
100%
893
Energy saving
monitor reference
(motor capacity)
0.1 to 55kW/
0 to 3600kW *1
895
Control selection
during commercial
power-supply
operation
Power saving rate
reference value
896
Power unit cost
897
0, 1 to 1000h,
Power saving
monitor average time 9999
Power saving
cumulative monitor 0, 1, 10, 9999
clear
0 to 100%,
Operation time rate
(estimated value)
9999
C0
(900)
C1
(901)
50Hz
C6
(904)
0 to 9999
899
0 to 400Hz
0
Free parameter 1
898
0%
0, 1, 2
0 to 5
LD/SLD
value of
applied
motor
capacity
C7
(905)
C8
(930)
C9
(930)
C10
(931)
C11
(931)
C42
(934)
C43
(934)
C44
(935)
C45
(935)
PU contrast
0, 1, 2, 3
0
0, 1, 9999
9999
0 to 500, 9999
9999
Initial
Value
0 to 300%
C5
(904)
*1
Terminal 2
frequency setting
bias frequency
Terminal 2
frequency setting
bias
Terminal 2
frequency setting
gain frequency
Terminal 2
frequency setting
gain
Terminal 4
frequency setting
bias frequency
Terminal 4
frequency setting
bias
Terminal 4
frequency setting
gain frequency
Terminal 4
frequency setting
gain
Setting
Range
0Hz
0
300 to 800V
Name
0 to 400Hz
0, 1
888
894
*1
Setting
Range
 991 adjustment
Pr.CL Parameter clear
ALLC All parameter clear
Er.CL Faults history clear
PCPY Parameter copy
10/100 *1
0, 1
0
0, 1, 2, 3
0
9999
9999
9999
CA terminal
calibration
⎯
⎯
AM terminal
calibration
⎯
⎯
The setting depends on capacities. (01160 or less/01800 or more)
15
TROUBLESHOOTING
7 TROUBLESHOOTING
When a fault occurs in the inverter, the inverter trips and the PU display automatically changes to any of the
following fault or alarm indications.
If the fault does not correspond to any of the following faults or if you have any other problem, please contact your
sales representative.
z Retention of fault output signal........... When the magnetic contactor (MC) provided on the input side of the
inverter is opened when a fault occurs, the inverter's control power will be
lost and the fault output will not be held.
z Fault or alarm indication ..................... When a fault or alarm occurs, the operation panel display automatically
switches to the fault or alarm indication.
z Resetting method ............................... When a fault occurs, the inverter output is kept stopped. Unless reset,
therefore, the inverter cannot restart. (Refer to page 16.)
z When any fault occurs, take the appropriate corrective action, then reset the inverter, and resume operation.
Not doing so may lead to the inverter fault and damage.
Inverter fault or alarm indications are roughly divided as below.
(1) Error message
A message regarding operational fault and setting fault by the operation panel (FR-DU07) and parameter unit
(FR-PU07/FR-PU04) is displayed. The inverter does not trip.
(2) Warnings
The inverter does not trip even when a warning is displayed. However, failure to take appropriate measures will
lead to a fault.
(3) Alarm
The inverter does not trip. You can also output an alarm signal by making parameter setting.
(4) Fault
When a fault occurs, the inverter trips and a fault signal is output.
7.1 Reset method of protective function
(1) Resetting the inverter
The inverter can be reset by performing any of the following operations. Note that the internal thermal integrated
value of the electronic thermal relay function and the number of retries are cleared (erased) by resetting the inverter.
Inverter recovers about 1s after the reset is released.
Operation 1: ..... Using the operation panel, press
to reset the inverter.
(This may only be performed when a fault occurs (Refer to the Instruction
Manual (applied) for fault.))
Operation 2:...... Switch power off once. After the indicator of the operation panel turns
OFF, switch it ON again.
ON
OFF
Operation 3: ..... Turn on the reset signal (RES) for more than 0.1s. (If the RES signal is
kept on, "Err." appears (flickers) to indicate that the inverter is in a reset
status.)
Inverter
RES
PC
16
TROUBLESHOOTING
7.2 List of fault or alarm display
Operation Panel
Indication
to
to
E.OLT
Stall prevention
E.GF
Output side earth fault
overcurrent
E.LF
Output phase loss
rE1 to 4 Copy operation error
Err.
Error
OL
Stall prevention (overcurrent)
oL
Stall prevention (overvoltage)
RB
Regenerative brake prealarm
TH
Electronic thermal relay function
prealarm
PS
PU stop
MT
Maintenance signal output
CP
Parameter copy
FN
Fan alarm
E.OC2
E.OC3
E.OV1
E.OV2
Fault
E.ILF*
Operation panel lock
Er1 to 4 Parameter write error
E.OC1
E.OV3
E.THT
E.THM
Name
Faults history
Overcurrent trip during
acceleration
Overcurrent trip during constant
speed
Overcurrent trip during
deceleration or stop
Regenerative overvoltage trip
during acceleration
Regenerative overvoltage trip
during constant speed
Regenerative overvoltage trip
during deceleration or stop
Inverter overload trip
(electronic thermal relay function)
Motor overload trip
(electronic thermal relay function)
E.FIN
Fin overheat
E.IPF
Instantaneous power failure
E.UVT
Undervoltage
External thermal relay operation*2
E.PTC*
PTC thermistor operation
E.OP1
E. 1
E.PE
E.PUE
/
/
/
Input phase loss
E.OHT
E.OPT
Fault
Alarm
Warnings
Error message
E--HOLD
Operation Panel
Indication
Name
Option fault
Communication option fault
(e.g.communication error)
Option fault
(e.g.connection or contact fault)
Parameter storage device fault
PU disconnection
E.RET
Retry count excess
E.PE2*
Parameter storage device fault
E. 5 /
E. 6 /
E. 7 /
E.CPU
CPU fault
E.CTE
Operation panel power supply
short circuit, RS-485 terminal
power supply short circuit
E.P24
24VDC power output short circuit
E.CDO*
Output current detection value
exceeded
E.IOH*
Inrush current limit circuit fault
E.SER*
Communication fault (inverter)
E.AIE*
Analog input fault
E.PID*
PID signal fault
E.BE
Brake transistor alarm detection/
internal circuit error
E.13
Internal circuit fault
* If an error occurs when using the FR-PU04, "Fault 14" is displayed
on the FR-PU04.
17
Appendix 1 Instructions for compliance with the EU Directives
The EU Directives are issued to standardize different national regulations of the EU Member States and to facilitate free movement of the
equipment, whose safety is ensured, in the EU territory.
Since 1996, compliance with the EMC Directive that is one of the EU Directives has been legally required. Since 1997, compliance with the
Low Voltage Directive, another EU Directive, has been also legally required. When a manufacturer confirms its equipment to be compliant
with the EMC Directive and the Low Voltage Directive, the manufacturer must declare the conformity and affix the CE marking.
z The authorized representative in the EU
The authorized representative in the EU is shown below.
Name: Mitsubishi Electric Europe BV
Address: Gothaer strase 8, 40880 Ratingen, Germany
z Note
We declare that this inverter conforms with the EMC Directive in industrial environments and affix the CE marking on the inverter. When
using the inverter in a residential area, take appropriate measures and ensure the conformity of the inverter used in the residential area.
(1) EMC Directive
We declare that this inverter conforms with the EMC Directive and affix the CE marking on the inverter.
y EMC Directive: 2004/108/EC
y Standard(s): EN61800-3:2004 (Second environment / PDS Category "C3")
Note: First environment
Environment including residential buildings. Includes buildings directly connected without a transformer to the low voltage power
supply network which supplies power to residential buildings.
Second environment
Environment including all buildings except buildings directly connected without a transformer to the low voltage power supply
network which supplies power to residential buildings.
z Note
Install the inverter and perform wiring according to the following instructions.
* The inverter is equipped with a built-in EMC filter. Set the EMC filter valid (initial setting).
* Connect the inverter to an earthed power supply.
* Install a motor and a control cable according to the instructions written in the EMC Installation Guidelines (BCN-A21041-204).
* The cable length between the inverter and the motor is 5 m maximum.
* Confirm that the final integrated system with the inverter conforms with the EMC Directive.
18
(2) Low Voltage Directive
We have self-confirmed our inverters as products compliant to the Low Voltage Directive (Conforming standard EN 50178) and affix the CE
mark on the inverters.
Outline of instructions
* Do not use an earth leakage current breaker as an electric shock protector without connecting the equipment to the earth. Connect the
equipment to the earth securely.
* Wire the earth terminal independently. (Do not connect two or more cables to one terminal.)
* Use the cable sizes on page 6 under the following conditions.
⋅ Surrounding air temperature: 40°C maximum
If conditions are different from above, select appropriate wire according to EN60204 Appendix C TABLE 5.
* Use a tinned (plating should not include zinc) crimping terminal to connect the earth cable. When tightening the screw, be careful not to
damage the threads.
For use as a product compliant with the Low Voltage Directive, use PVC cable whose size is indicated on page 6.
* Use the moulded case circuit breaker and magnetic contactor which conform to the EN or IEC Standard.
* When using an earth leakage current breaker, use a residual current operated protective device (RCD) of type B (breaker which can
detect both AC and DC). If not, provide double or reinforced insulation between the inverter and other equipment, or put a transformer
between the main power supply and inverter.
* Use the inverter under the conditions of overvoltage category II (usable regardless of the earth condition of the power supply),
overvoltage category III (usable with the earthed-neutral system power supply, 400V class only) and pollution degree 2 or lower
specified in IEC664.
⋅ To use the inverter of 00770 or more (IP00) under the conditions of pollution degree 2, install it in the enclosure of IP 2X or higher.
⋅ To use the inverter under the conditions of pollution degree 3, install it in the enclosure of IP54 or higher.
⋅ To use the inverter of 00620 or less (IP20) outside of an enclosure in the environment of pollution degree 2, fix a fan cover with fan
cover fixing screws enclosed.
Fan cover
fixing screws
Fan cover
fixing screw
Fan cover
Fan cover
Fan cover
Fan
Fan
00083, 00126
Fan cover
fixing screw
Fan
00170 to 00380
00470, 00620
* On the input and output of the inverter, use cables of the type and size set forth in EN60204 Appendix C.
* The operating capacity of the relay outputs (terminal symbols A1, B1, C1, A2, B2, C2) should be 30VDC, 0.3A. (Relay output has basic
isolation from the inverter internal circuit.)
* Control circuit terminals on page 3 are safely isolated from the main circuit.
* Environment
Surrounding air
temperature
Ambient humidity
Maximum altitude
During Operation
In Storage
LD: -10°C to +50°C
SLD (initial setting): -10°C to +40°C
-20°C to +65°C
During Transportation
-20°C to +65°C
90% RH or less
1000m
90% RH or less
1000m
90% RH or less
10000m
Details are given in the technical information "Low Voltage Directive Conformance Guide" (BCN-A21041-203). Please contact your sales
representative.
19
Appendix 2 Instructions for UL and cUL Compliance
(Conforming standard UL 508C, CSA C22.2 No.14)
(1) Installation
This inverter is UL-listed as a product for use in an enclosure. Design an enclosure so that the inverter surrounding air
temperature, humidity and atmosphere satisfy the specifications. (Refer to page 1.)
Wiring protection
For installation in the United States, branch circuit protection must be provided in accordance with the National
Electrical Code and any applicable provincial codes.
For installation in Canada, branch circuit protection must be provided in accordance with the Canadian Electrical Code
and any applicable provincial codes.
Provide the appropriate UL and cUL listed Class RK5, Class T or Class L type fuse or UL489 molded case circuit
breaker (MCCB) that is suitable for branch circuit protection in accordance with the table below.
Note, the Class L fuses can be used if the applicable current rating is larger than 600A.
FR-F740-†††††-EC
00023 00038 00052 00083 00126 00170 00250 00310 00380 00470 00620 00770 00930 01160
Rated fuse voltage(V)
Without power
Fuse
factor improving
maximum reactor
allowable
With power factor
rating (A)* improving reactor
Molded case circuit breaker
(MCCB)
maximum allowable rating (A)*
FR-F740-†††††-EC
480V or more
6
10
15
20
30
40
70
80
90
110
150
175
200
250
6
10
10
15
25
35
60
70
90
100
125
150
175
200
15
15
15
20
30
40
60
70
90
100
150
175
225
250
01800 02160 02600 03250 03610 04320 04810 05470 06100 06830 07700 08660 09620 10940 12120
Rated fuse voltage(V)
Without power
Fuse
factor improving
maximum reactor
allowable
With power factor
rating (A)* improving reactor
Molded case circuit breaker
(MCCB)
maximum allowable rating (A)*
500V or more
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
⎯
300
350
400
500
600
700
800
900
450
500
600
800
900
1000 1200 1200 1200 1600 1600 2000 2000 2500 3000
1000 1100 1200 1350 1500 1800 2000
* Maximum allowable rating by US National Electrical Code at SLD rating.
Exact size must be chosen for each installation.
(2) Wiring of the power supply and motor
For wiring the input (R/L1, S/L2, T/L3) and output (U, V, W) terminals of the inverter, use the UL Listed copper, stranded
wires (rated at 75°C) and round ring crimping terminals. Crimp the crimping terminals with the crimping tool
recommended by the terminal maker.
(3) Short circuit ratings
• Model 01160 or less
Suitable For Use in A Circuit Capable Of Delivering Not More Than 100kA rms Symmetrical Amperes, 528V Maximum.
• Model 01800 or more
Suitable For Use in A Circuit Capable Of Delivering Not More Than 100kA rms Symmetrical Amperes, 550V Maximum.
20
(4) Motor overload protection
(min) unit display in
this range
3
3
Characteristic when
electronic thermal relay
function for motor
protection is turned off
(When Pr. 9 setting is 0(A))
240
Operation time (s)
(s) unit display in this range
Operation time (min)
This inverter is certified as a motor overload protection device by UL.
When using the electronic thermal relay function as motor overload protection, set the rated motor current to Pr. 9
Electronic thermal O/L relay.
Electronic thermal relay function operation characteristic
This function detects the overload (overheat) of the
motor, stops the operation of the inverter's output
Pr. 9 = 50% setting of
Pr. 9 = 100% setting
inverter rating*1.2
of inverter rating*1.2
transistor, and stops the output. (The operation
characteristic is shown on the left)
70
30Hz or more*
30Hz
⋅ When using the Mitsubishi constant-torque motor
20Hz
or more*
Operation range
Range
on
the
right
of
10Hz
20Hz
1) Set "1" in Pr. 71. (This provides a 100% continuous torque
60
characteristic curve
10Hz
6Hz
Non-operation range
characteristic in the low-speed range.)
6Hz
Range on the left of
0.5Hz
characteristic curve
50 0.5Hz
2) Set the rated current of the motor in Pr. 9.
180
*1
120
Electronic thermal relay
function for transistor
protection
60
52.5%
105%
100 120
50
150
Inverter output current (%)
(% to the rated output current)
*2
*3
When 50% of the inverter rated output current (current value) is set
in Pr. 9
The % value denotes the percentage to the inverter rated output current.
It is not the percentage to the motor rated current.
When you set the electronic thermal relay function dedicated to the
Mitsubishi constant-torque motor, this characteristic curve applies
to operation at 6Hz or higher.
CAUTION
⋅ Protective function by electronic thermal relay function is reset by inverter power reset and reset signal input. Avoid
unnecessary reset and power-off.
⋅ When multiple motors are operated by a single inverter, protection cannot be provided by the electronic thermal relay function.
Install an external thermal relay to each motor.
⋅ When the difference between the inverter and motor capacities is large and the setting is small, the protective characteristics of
the electronic thermal relay function will be deteriorated. In this case, use an external thermal relay.
⋅ A special motor cannot be protected by the electronic thermal relay function. Use the external thermal relay.
⋅ Electronic thermal relay may not function when 5% or less of inverter rated current is set to electronic thermal relay setting.
21
MEMO
22
MEMO
23
MEMO
24
REVISIONS
*The manual number is given on the bottom left of the back cover.
Print Date
May 2004
Aug. 2004
*Manual
Revision
Number
IB(NA)-0600189ZZZ-A
IB(NA)-0600189ZZZ-B
First edition
Additions
⋅ FR-F740 - 02600 to 03610 - EC
⋅ Pr.299 Rotation direction detection selection at restarting
Oct. 2004
IB(NA)-0600189ZZZ-C
Additions
⋅ FR-F740 - 04320 to 12120 - EC
Jun. 2005
IB(NA)-0600189ZZZ-D
Additions
⋅ Instructions for wiring of the main circuit of the FR-F740-05470 or more
⋅ Electronic thermal relay function operation characteristic
May 2006
IB(NA)-0600189ZZZ-E
Additions
⋅ Pr. 539 Modbus-RTU communication check time interval
⋅ Voltage/current input switch
Jul. 2008
IB(NA)-0600189ZZZ-F
Additions
⋅ Breaker selection when using the inverter as UL or cUL listed product
⋅ Setting values "10, 11" of Pr.495 Remote output selection
Sep. 2009
IB(NA)-0600189ZZZ-G
Additions
・ Pr. 59 Remote function selection setting value "11 ", "12 ", "13 "
・ Pr. 29 Acceleration/deceleration pattern selection setting value "6"
・ Pr. 30 Regenerative function selection setting value "10", "11", "20", "21"
・ Pr.128 PID action selection setting value "110", "111", "120", "121"
・ Pr.167 Output current detection operation selection setting value "10", "11"
・ Pr.178 to Pr.189 Input terminal function selection setting value "70", "71", "72"
・ Pr.190 to Pr.196 Output terminal function selection setting value "48", "79", "85",
"148", "179", "185"
・ Pr. 261 Power failure stop selection setting value "21", "22"
・ Pr.522 Output stop frequency
・ Pr.653 Speed smoothing control、Pr.654 Speed smoothing cutoff frequency
・ Pr.553 PID deviation limit、Pr.554 PID signal operation selection、C42 (Pr.934) PID
C43 (Pr.934) PID display bias analog value、
C44 (Pr.935) PID
display bias coefficient、
display gain coefficient、C45 (Pr.935) PID display gain analog value
・ Pr.799 Pulse increment setting for output power
Partial changes
・Pr.153 Zero current detection time setting range "0 to 10s"
・Appendix 1 Instructions for compliance with the EU Directives
For Maximum Safety
• Mitsubishi inverters are not designed or manufactured to be used in equipment or systems in situations that
can affect or endanger human life.
• When considering this product for operation in special applications such as machinery or systems used in
passenger transportation, medical, aerospace, atomic power, electric power, or submarine repeating
applications, please contact your nearest Mitsubishi sales representative.
• Although this product was manufactured under conditions of strict quality control, you are strongly advised
to install safety devices to prevent serious accidents when it is used in facilities where breakdowns of the
product are likely to cause a serious accident.
• Please do not use this product for loads other than three-phase induction motors.
25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement