Model: GMRS100 Owner's Manual 128-XXXX 1 of 24

Model:  GMRS100 Owner's Manual 128-XXXX 1 of 24
General Mobile Radio Service (GMRS)
Model: GMRS100
Owner's Manual
HI LO
MODE
Released:
3-10-03
128-XXXX
1 of 24
CAUTION
NEVER ATTEMPT TO CHARGE ALKALINE OR DRY CELL BATTERIES, AS
BATTERIES MAY BURST CAUSING PERSONAL INJURY AND DAMAGE
TO THE PRODUCT. WHEN RECHARGING NICKEL METAL HYDRIDE (NiMH) BATTERIES WITH THE SUPPLIED AUDIOVOX CHARGER AND WALL
ADAPTER, USE ONLY AUDIOVOX-APPROVED RECHARGEABLE BATTERIES. USE OF THE AUDIOVOX CHARGER WITH OTHER BRANDS OF BATTERIES IS NOT RECOMMENDED, AS BATTERY CHARGING TIMES WILL
VARY WITH DIFFERENT BRANDS. REFER TO THE MANUFACTURER’S
INSTRUCTIONS FOR CHARGING OTHER BRANDS OF BATTERIES.
AVOID PLACING THE GMRS122-2 RADIO TRANSCEIVER FOR PROLONGED PERIODS OF TIME IN DIRECT SUNLIGHT OR TEMPERATURES
BELOW -4° F (-20° C) OR ABOVE 140 ° F (60° C).
KEEP THE ANTENNA AT 1 INCH (2.5 cm) AWAY FROM YOUR HEAD AND
BODY. DO NOT USE YOUR GMRS122-2 RADIO TRANSCEIVER WITH A
DAMAGED ANTENNA.
PLACE THE RUBBER COVERS ON JACKS WHEN NOT IN USE.
GMRS LICENSE:
USE OF THIS RADIO WITHIN THE UNITED STATES REQUIRES AN FCC
GMRS LICENSE. AN INDIVIDUAL 18 YEARS OF AGE OR OLDER, WHO IS
NOT A REPRESENTATIVE OF A FOREIGN GOVERNMENT, IS ELIGIBLE
TO APPLY FOR A GMRS SYSTEM LICENSE. YOU WILL NEED TWO FORMS
FROM THE FCC; FCC FORM 159 AND FCC FORM 605 MAIN FORM AND
SCHEDULE F. YOU CAN FIND THE FORMS ONLINE AT:
HTTP://WWW.FCC.GOV/FORMPAGE.HTML, OR CALL 1-800-418-3676.
2
128-XXXX
2 of 24
Model GMRS100 (FCC License Required)
6
5
4
8
PTTPTT
M M
3
3
(REF)
HI LO
11
12
MODE
2
10
13
9
7
1
1
(REF)
1.
2.
3.
4.
Battery Cover
Monitor (M) Button
Detachable Carry Clip
Push-To-Talk (PTT) and Function Confirmation Button
5. Antenna
6. External Speaker (SP)/
Microphone (MIC)/CHG Jack
7. Built-in Speaker
14
8. Liquid Crystal Display (LCD)
9. Built-in Microphone
10. Up Channel/Volume Button
11. Down Channel/Volume
Button
12. MODE/VOX Button
13. Power On/Off and SCAN
Button
14. Battery Charging Contacts
3
128-XXXX
3 of 24
Model GMRS100 DISPLAY
6
7
1
2
HI LO
8
3
9
4
10
11
5
1. Roger Beep Tone Indicator: This icon appears when the Roger Beep
tone is on, and disapppears when the tone is not in use.
2. Transmit Indicator: Icon appears when the unit is in the transmit
mode (PTT button activated or VOX mode active).
3. Busy Indicator: This icon appears when the unit is receiving a
transmission.
4. Large Segment Display: Indicates the channel number in use between
1 and 22.
5. Scan Indicator: This function allows the user to scan a chanel every
0.5 second to search for a valid signal.
6. HI/LO Indicators: Appropriate icon appears when the transmit power
is set to desired output power.
7. Battery Level Indicator: Icon appears flashing to indicate low
battery charge level.
8. Small Segment Display: Indicates the CTCSS tone code (1-38)
function is active for the main channel in use.
9. Monitor Indicator: This function is not used.
10.Key Lock Indicator: This function is not used.
11. Voice Activated Transmission (VOX) Indicator: This function allows
hands-free conversation. The icon appears when the VOX mode is
activated.
4
128-XXXX
4 of 24
Equipment and Accessories Supplied
1.
2.
Radio (4)
Owner’s Manual (1)
GMRS100
128-XXXX
Optional Accessories
1.
2.
3.
Rechargeable Batteries (4)
Boom Microphone/Headset
Leather Carrying Case
NiMH, P/N GMRS1222BAT
GMRSBHST4
GMRS1502LC
Powering the transceiver:
Your GMRS100 radio transceiver operates on four rechargeable batteries.
Only approved rechargeable batteries can be recharged in the
GMRS4WM wall mount charger. This will ensure optimum performance
for the GMRS100. Battery charging time is typically 10-12 hours.
Use of other brands of rechargeable batteries is not recommended as
battery charging time will vary. Do not mix old and new, or batteries of
differing manufacture, since the charging will be uneven and will
result in decreased battery life.
If necessary, four AAA alkaline batteries can be used to power the GMRS100,
but note that these type batteries can not be recharged and damage to
the charger or the batteries may result if the units are placed in the
GMRS4WM wall mount charger with the alkaline batteries are installed.
FOR THIS REASON, IT IS NOT RECOMMENDED TO USE ALKALINE
BATTERIES IN THE GMRS100.
DO NOT PLACE GMRS100 TRANSCEIVERS IN THE CHARGING
STAND IF THERE ARE ALKALINE BATTERIES INSTALLED.
5
128-XXXX
5 of 24
Installing the batteries:
Battery installation is made more convenient when the carry clip is either
rotated left or right to the horizontal position, or is removed. Simply rotate
the clip in either direction to the horizontal position. Be careful not to use
excessive force. To remove the clip, press down on the spring release tab
and pull the clip straight out from the radio body. Next, press down with the
thumb at the embossed arrow, slide the battery cover down and lift it away
from the compartment. Insert four AAA batteries (alternate positive ends (+)
toward the top of the transceiver, starting left-to-right.
CLIP SPRING
RELEASE TAB
COVER
ARROW
CARRY
CLIP
+
+
BATTERY
COVER
1. Using thumb,
press down on
battery cover at
arrow and slide
cover down.
2. Then lift cover at
bottom to open.
Remove cover.
POSITIVE
TERMINALS
+
+
3. Insert four AAA batteries
(positive (+) end toward
the top begining at left
side and alternating
positive terminals as
shown).
6
128-XXXX
6 of 24
The following guidelines will improve performance and provide longer
operating times for the GMRS100:
1. Do not mix old and new batteries.
2. Do not mix alkaline, standard (carbon-zinc) or rechargeable
batteries.
3. If the unit is not to be used for an extended period of time, remove the
batteries. Old or leaking batteries can cause damage to the unit and
will void the warranty.
MIC/CHG/
SPK JACK
HI LO
MODE
GMRS100
NOTE : O nly Audiovox
approved rechargeable
batteries (P/N GMRS1222BAT)
can be recharged in the radio
transceiver.
7
128-xxxx
7 of 24
GMRS100 OPERATIONAL MODES
GMRS/FRS
(MODE)
CHANNEL
SELECT
(1-22)
CTCSS
SELECT
(oF, 01-38)
POWER
SELECT
(GMRS channels only)
ROGER
BEEP
(on or oF)
NOTE: To differentiate between operating modes, look for HI or LO
indication below the battery power level indicator when in GMRS
mode.Refer to the appropriate section of this manual for detailed operating instructions for each mode. Channels 1 through
7 are shared GMRS/FRS. Channels 8 through 14 are FRS only,
and channels 15 through 22 are GMRS only.
Controls:
Power On-Off/SCAN Button (13)
Press and hold the PWR on/off button for at least 2 seconds. You will hear
a confirming melody to indicate the unit is on. To turn the unit off, press and
hold the button for at least 2 seconds.
Adjusting the Volume (11, 10)
) to
With the unit powered on, press the Up Channel/Volume button (
increase volume and the Down Channel/Volume button (
) to decrease
8
128-xxxx
8 of 24
volume. The display will indicate the current volume level (VL) followed by
the number (0-7). As volume is increased upward, the unit will beep at
each step, and vice-versa. When the minimum and maximum volume
settings are reached, a unique tone will sound.
Monitor/Display Backlight Button (2)
This button is used to to check activity on the current frequency before
transmitting. Check activity by pressing the Monitor (M) Button longer
than 2 seconds; the
icon will apppear on the display and you will
hear static if frequency is clear. Do not transmit if you hear conversation.
Hold down the Monitor Button again longer than 2 seconds and the
icon will disapppear from the display.
The monitor function will temporarily bypass the squelch setting and play
all signals on a given channel. This feature is useful when communicating
with other parties at extreme range.
By pressing the monitor button momentarily, the LCD backlight is turned
on; the LCD backlight will turn off automatically in about 5 seconds, unless
the monitor button is pressed momentarily once again.
Push To Talk (PTT) Button (4)
Pressing and holding this button will allow you to speak to any transceiver
that is set to the same channel and privacy code setting as yours. Hold the
transceiver approximately 1 to 2 inches from your face as you speak into
the built in microphone (9). After you have finished speaking, release the
PTT Button to allow reception of incoming signals. It is not possible to
transmit and receive at the same time. Whenever the button is pressed,
the transmit signal icon (
) will appear in the upper left corner of the
display. Releasing the button allows the unit to revert to standby mode.
icon will appear.
When receiving an incoming signal, the
The PTT Button can also be used as a two-way call ringer. Pressing the
button twice quickly will call another party on the same channel. The transmit
icon ( ) will be displayed for 3 seconds and then disappear.
9
128-xxxx
9 of 24
Up Channel/Volume Button (10)
In the standby mode, pressing this button will increment the listening
volume. When in function edit mode this button will be used to adjust the
unit’s settings.
Down Channel/Volume Button (11)
In the standby mode, pressing this button will decrement the listening
volume. When in function edit mode this button will be used to adjust the
unit’s settings.
MODE Button (12)
This button is used to select various feature settings in the GMRS and FRS
modes.
External Speaker (SPK)/ Microphone (MIC)/CHG Jack (6)
This jack accepts both the optional Audiovox headset/microphone connector.
For additional equipment and accessories for the GMRS100, visit the
Audiovox web site at www.audiovox.com <http://www.audiovox.com/>
Scan Button (13)
With the unit in standby mode, press the Power On/Off Button momentarily
to enable or disable the scan function; SCAN will appear on the display.
10
128-xxxx
10 of 24
Operating Modes and Features
GRMS/FRS Operation:
- Press and hold the Power On/Off button for 2 seconds to turn on
power.
- Press the MODE button so the Channel number flashes.
- Select the desired channel with the Up (10) and Down (11) Buttons.
When receiving a call, the
icon appears to indicate an incoming
call.
- Press and hold the PTT button (4) to transmit, then speak into the
microphone clearly and slowly. The Transmit icon (
) appears
on the display while the button is pressed.
- Release PTT Button (4) to receive.
- Communication can only be accomplished when the channel and
CTCSS tone frequency of at least two parties are the same.
- The CTCSS subcode (01-38) will be displayed on the LCD panel if the
CTCSS tone frequency function is enabled (not oF).
Channel Selection
In order to communicate with other GMRS/FRS units, both the transmitting and receiving party must be on the same frequency.
The GMRS100 has 22 channels (frequencies) indicated by the large
digits on the LCD display panel. Channels 1 through 7 are the shared
GMRS/FRS channels. Channels 8-14 are FRS only channels, while channels 15-22 are assigned GMRS only channels. If an FRS only channel (814) has been selected, the HI or LO icon will not be displayed on the LCD
panel; otherwise, for channels 1-7 (GMRS/FRS) and 15-22 (GMRS only)
the HI or LO icon will be displayed. Communication with Audiovox GMRS/
FRS and compatible units is possible on these 22 channels. Before transmitting on the selected channel, press the Monitor (M) Button (2) to check
the activity on that channel. If there is activity on the selected channel,
change to another channel that is clear.
11
128-xxxx
11 of 24
To change the channel:
- From GMRS/FRS standby mode, press the MODE button (12) once
the channel number flashes.
- Press the Up Button (10) briefly to move to the next higher main channel number.
- Press the Down Button (11) briefly to move to the next lower main
channel number.
- Press the PTT button momentarily to confirm selection.
CTCSS Mode (Sub-Channel) Selection
The Coded Tone Controlled Squelch System (CTCSS) has 38 Sub-Frequencies.
This feature allows you to utilize the coded squelch tones (01-38) within a
main channel and enables you to communicate with another party on the
same main channel using the same subcode. (This filters out unwanted
transmissions from the same main channel). Since there are 38 CTCSS
Sub-channels for each main channel, a different subcode may be selected for each of the 22 channels.
To change the CTCSS Sub-channel:
- From GMRS/FRS standby mode, press the MODE Button twice; a flash
ing oF or sub-channel number is displayed.
- Press the Up or Down button to select the desired sub-channel for
use (01-38 ).
- Press the PTT button to confirm selection.
The CTCSS mode can be turned off by selecting the oF icon as the setting.
NOTE:
To communicate with other GMRS/FRS units, they must be
switched to the same channel and CTCSS subcode. To communicate with other GMRS units that do not have subcodes, switch
your unit to the same channel with the subcode set to oF.
The CTCSS subcodes do not prevent others from hearing your
transmission. This will only allow you to ignore all traffic on a
given channel not using the same subcode.
12
128-6675
12 of 24
Transmit Power Selection Mode (GMRS Channels Only)
This feature permits selection of the transmitting power level to high
or low when using channels 1-7 and 15-22. Using low power, the unit
will have a lower transmit range, but battery life will be increased.
NOTE:
You will find that for the majority of your needs, the low-power
setting will provide adequate communications on all channels;
there should seldom be any need to use high power, except in
situations where you need absolute maximum range. Using low
power will greatly extend battery life. We suggest you experiment with switching between low and high power.
To access the transmitter power selection function:
- From GMRS standby mode, press the MODE Button 3 times until the
Po indication appears flashing on the display with a steady Hi or Lo
indication.
- Press the Up or Down button to toggle between the High and Low selections.
- Press the PTT button to confirm selection.
The display will indicate the current setting in standby mode.
Roger Beep Tone
The Roger Beep is a tone which is automatically transmitted whenever the
PTT button is released and the tone is enabled. This tone alerts the
receiving party that the transmission has been terminated intentionally.
13
128-xxxx
13 of 24
To enable and disable the Roger Beep tone:
- From GMRS/FRS standby mode, press the MODE Button 4 times (in
FRS mode, 3 times) until the flashing Roger Beep icon ( ) appears
with On or oF.
- Press the Up or Down Button to select the tone on or off as desired.
- When enabled, the tone icon (
) appears steady on the display.
- Press the PTT button momentarily to confirm selection.
VOX Selection Mode
This option enables you to have hands-free conversation. When using the
internal microphone/speaker or external microphone/headset (purchased
separately), your voice or the signal is detected and the radio transmits
and receives automatically. Your voice or nearby sound is detected and
the radio transmits without the need to press the PTT button.
To set the radio for VOX operation:
- From GMRS/FRS standby mode, press and hold the MODE button
for 3 seconds, or until the VOX icon appears on the display.
- To terminate VOX operation, press and hold the MODE button for at
least 3 seconds; the VOX indication will disappear.
Button Beep (Key Tone)
This feature allows the transceiver to sound a confirmation tone whenever
the following keys are pressed: Power On/Off/SCAN Button, Up/Down Buttons and MODE Button. This feature is always on.
Call Ringer Selection Mode
The transceiver provides a transmit call ring melody at the receiving unit to
alert you to an incoming call.
To activate the call ringer melody:
- From GMRS/FRS standby mode, press the PTT button twice in quick
succession; a call ring melody will sound at the receiving unit to alert
the user to an incoming transmission, provided that unit is equipped
with this capability and set to the same channel.
14
128-xxxx
14 of 24
Channel Scan Operation
This feature allows you to monitor all channels automatically for valid
signals. While scanning, you can transmit and receive. When a signal is
received, the scan is interrupted and will return to scan mode approximately 5 seconds after reception is terminated.
NOTE:
While the SCAN mode is active, the MODE button is inoperative. In addition, the scan mode will reduce the overall battery life
since the battery save function is overridden.
To enable the channel scan mode:
- From GMRS/FRS standby mode, momentarily press the Power On/Off
Button; SCAN will appear on the LCD display.
- The radio will automatically display each channel (1-22) in ascending
order to find an active main channel.
- When the unit doesn’t find any signals and you want to transmit, press
the PTT Button to return to primary channel operation. The transceiver
will automatically resume scanning approximately 15 seconds after
the communication is completed.
- If there is no activity and you want to leave the scan mode, press the
Power On/Off button momentarily and the unit will return to normal op
eration; the SCAN icon will disappear from the LCD display.
15
128-xxxx
15 of 24
Battery Alert
When the battery icon (
) blinks steadily on the LCD panel, recharge
the unit or install fresh batteries.
NOTES FOR GOOD COMMUNICATION
1 . The GMRS100 22 channels are shared on a ‘take turns’ basis.
This means other groups may be talking on any of the channels.
A common code of ethics/courtesy is to switch to another vacant
channel and not to attempt to talk over someone who is already using
the channel you first selected.
2. The GMRS100 has been designed to maximize performance
and improve transmission range in the field. To avoid interference,
it is recommended that you do not use the units closer than 5 feet
apart.
3. For best transmission results, always keep your mouth about 2-3
inches from the microphone (9) and speak slowly in a normal voice.
4. To increase battery life, use the SCAN feature sparingly. This
feature will reduce operating time considerably.
Warning
• Do not operate the transceiver unless you are licensed to do so.
• Remove the batteries from the transceiver if it is not expected to be used
for long periods. This will eliminate the possibility of chemicals leaking
from the batteries and corroding the transceiver.
• Avoid exposing the transceiver to water or extremes of temperature.
• Do not use this device in or near a mining facility, which uses remotely
triggered explosives or in areas labeled “Blasting Area”. Premature or
accidental detonation may result.
16
128-xxxx
16 of 24
• Do not attempt to modify or in any way increase the output of this
transceiver. Its output is designed to meet the legal limits set by the FCC.
• Do not use this device or change its batteries in potentially explosive
atmospheres as sparks in such areas could result in an explosion.
• Turn your transceiver off wherever posted notices restrict the use of radios
or cellular telephones. Facilities such as hospitals may use equipment
that is sensitive to RF energy.
• Turn your transceiver off on board aircraft when requested to do so.
• Do not place your radio in front of a vehicle’s air-bag. If the air-bag
deploys, it could propel the transceiver like a projectile causing bodily
injury.
17
128-xxxx
17 of 24
Troubleshooting
Problem
Possible cause
Correction
No transmission
while pressing
the PTT Button
Weak batteries
Incorrect battery polarity
Charge or replace batteries
Install the batteries
following the directions in
paragraph Installing the
Batteries.
Weak or no
signal received
Weak batteries
Channel and privacy
code not set the same
as target transceiver
Charge or replace batteries
Adjust the transceiver’s
settings to match those
settings of the target
transceiver
Increase volume level
Release PTT Button
Volume level too low
PTT Button inadvertently
depressed
Excessive radio interference
on a particular channel
Obstruction of radio signal
Unit beeps, but
will not function
when turned on
Reception of
unwanted signals
Batteries extremely
discharged
CTCSS privacy mode
not on
Interference from
electronic devices such
as computers or TVs
Change to a different
channel
Avoid operating in or near
large buildings or vehicles
Charge or replace batteries
Turn on the CTCSS privacy
mode and set code number to
match the setting of the
target transceiver.
Turn the devices off or move
farther away from them.
18
128-xxxx
18 of 24
Tec
hnical Specif
ica
tions:
echnical
Specifica
ications:
General
Frequency Range:
Channels 1 through 7 are
shared with FRS radios.
Channels 8 through 14 are
FRS only.
Channels 15 through 22 are
GMRS only.
Channel Spacing
Privacy Codes
Dimensions (W x H x D)
(Without Antenna)
Refer to frequency chart on next page.
Refer to frequency chart on next page.
Refer to frequency chart on next page.
12.5kHz
38 for each main channel
2.25” W x 3.68” H x 1.125” D
(56.0 mm x 93.7 mm x 28.5 mm)
Power Supply
Power Source
Ni-MH rechargeable, AAA (4),
4.8 VDC, 650 mAh
Operating Time
(Transmit: Receive: Standby)
(5: 5: 90 ratio)
18 hours Low Power
11 hours High Power
Receiver
Useable Sensitivity
Maximum Audio Output Power
Modulation Distortion
>-119 dBm
> 0.3 Watt maximum (8 Ohm )
< 5% (1 kHz 70%)
Tr ansmitter
RF Output Power
Maximum Deviation
Modulation Distortion
1.8 Watts maximum (high power)
0.5 Watt maximum (low power)
+/- 2.5 kHz
< 5% (1 kHz 70%)
19
128-xxxx
19 of 24
This transceiver complies with FCC regulations for use in the United
States of America. Use in other countries may be prohibited or restricted
by local regulation. Please check with the local regulating agency before using this device outside the United States of America.
Main Channel Frequencies:
CHANNEL /TYPE
FREQ (MHz )
CHANNEL /TYPE
FREQ (MHz )
1
GMRS/FRS
462.5625
12
FRS
467.6625
2
GMRS/FRS
462.5875
13
FRS
467.6875
3
GMRS/FRS
462.6125
14
FRS
467.7125
4
GMRS/FRS
462.6375
15
GMRS
462.5500
5
GMRS/FRS
462.6625
16
GMRS
462.5750
6
GMRS/FRS
462.6875
17
GMRS
462.6000
7
GMRS/FRS
462.7125
18
GMRS
462.6250
8
FRS
467.5625
19
GMRS
462.6500
9
FRS
467.5875
20
GMRS
462.6750
10 FRS
467.6125
21
GMRS
462.7000
11 FRS
467.6375
22
GMRS
462.7250
NOTE: Channels 1 through 7 are shared with FRS radios.
Channels 8 through 14 are FRS only.
Channels 15 through 22 are GMRS only.
20
128-xxxx
20 of 24
Continuous Tone Coded Squelch System Tone
Frequencies (in Hz)
CTCSS
Freq. Hz
CTCSS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
67.0
71.9
74.4
77.0
79.7
82.5
85.4
88.5
91.5
94.8
97.4
100.0
103.5
107.2
110.9
114.8
118.8
123.0
127.3
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
Freq. Hz
131.8
136.5
141.3
146.2
151.4
156.7
162.2
167.9
173.8
179.9
186.2
192.8
203.5
210.7
218.1
225.7
233.6
241.8
250.3
* oF = No Tone
21
128-xxxx
21 of 24
90 DAY / 12 MONTH LIMITED WARRANTY
AUDIOVOX SPECIALIZED APPLICATION, LLC (the Company) warrants to the original retail purchaser
of this product that should this product or any part therof, under normal use and conditions, be
proven defective in material or workman ship within 90 days from the date of original purchase,
such defect(s) will be repaired or initial 90 day period and for a period of 12 months from the date
of original purchase, the Company will supply at no charge a replacement for any defective part(s),
but will charge for the labor to repair the product.
To obtain repair or replacement within the terms of this warranty, the product is to be delivered
with proof of warranty coverage (e.g. dated bill of sale), specification of defect(s), transportation
prepaid, to an approved warranty station, or the Company at the address shown below.
This warranty does not extend to the elimination of externally generated static or noise, to the
correction of antenna problems, to costs incurred for removal or reinstallation of the product, or
to damage to any tapes, speakers, accessories, or electrical systems.
This warranty does nor apply ro any product or part thereof which, in the opinion of the
Company, has been damaged through alteration, improper installation, mishandling, misues,
neglect, or accident. THE EXTENT OF THE COMPANY'S LIABILITY UNDER THIS WARRANTY IS LIMITED
TO THE REPAIR OR REPLACEMENT PROVIDED ABOVE, AND, IN NO EVENT, SHALL THE COMPANY'S
LIABILITY EXCEED THE PURCHASE PRICE PAID BY THE PURCHASER FOR THE PRODUCT.
This warranty is in lieu of all other express warranties or liabilities. ANY IMPLIED WARRANTEIS,
INCLUDING ANY IMPLIED WARRANTY OF MARCHANTABILITY, SHALL BE LIMITED TO THE DURATION
OF THIS WARRANTY. ANY ACTION FOR BREECH OF ANY WARRANTY HEREUNDER INCLUDING ANY
IMPLIED WARRANTY OF MERCHANTABILITY MUST BE BROUGHT WITHIN A PERIOD OF 30 DAYS
FROM THE DATE OF ORIGINAL PURCHASE. IN NO CASE SHALL THE COMPANY BE LIABLE FOR ANY
COMSEQUENTIAL OR INCIDENTAL DAMAGES FOR BREECH OF THIS OR ANY OTHER WARRANTY,
EXPRESS OR IMPLIED, WHATSOEVER. No person or representative is authorized to assume for the
Company any liability other that expressed herein in connection with the sale of this product.
Some states do not allow limitations on how long an implied warranty lasts or the exclusion or
limitation of incidental or consuquential damages so the above limitations or exclusions may not
apply to you. This warranty gives you specific legal rights and you may also have other rights
which vary from state to state.
AUDIOVOX SPECIALIZED APPLICATIONS, LLC
Visit us at www.asaelectronics.com
22
128-xxxx
22 of 24
THIS PAGE LEFT BLANK INTENTIONALLY
128-6675
23 of 24
www.as aelectronics .com
P rinted in C hina
128-xxxx
128-xxxx
24 of 24
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement