DL405 Ethernet Communications Module Technical Specs

DL405 Ethernet Communications Module Technical Specs
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Communication Modules
Ethernet
Communications
Module
H4-ECOM100 <--->
H4-ECOM-F <--->
Simple connections
Use Category 5 UTP cables or 62.5/125
ST-style fiber optic cables depending
on the requirements of your application. Inexpensive UTP cables can be
run up to 100 meters between nodes,
and fiber optic cables can be run up to
2,000 meters. Fiber optic cables virtually
eliminate electrical noise problems. Use
repeaters to extend distances and expand
the number of nodes.
Our HA-TADP (10/100Base-T) PC network
adapter card is compatible with the
ECOM modules. See the Communications
Products section in this catalog for information on the adapter card.
Overview
Ethernet Communications Modules offer
features such as:
• High-speed peer-to-peer networking
of PLCs
• Fast updates with DirectSOFT Programming
Software
• High-performance access for Human
Machine Interface (HMI), ERP, MES or
other Windows-based software
• Industry standard ModbusTCP/IP
Client/Server Protocol (H4-ECOM100)
• Free SDK for custom drivers
• Easy setup
The Ethernet Communication (ECOM)
Modules support high-speed peer-to-peer
networking of PLCs. No longer are you
forced to designate a single PLC to be
the network master. Any PLC can initiate
communications with any other PLC. Link
your PLCs with PCs using industry standard Modbus TCP/IP protocol connected
through standard cables, hubs, and
repeaters. Or, use our KEPDirect I/O
Server to link to your favorite HMI/SCADA,
data historian, MES or ERP software to
DirectLOGIC PLCs. Our LookoutDirect
HMI and our DataWorx data collection software include ECOM drivers.
DirectSOFT Programming Software can
be used to monitor or update the program
in any DirectLOGIC PLC on the network.
Specifications
Communications
Data Transfer Rate
Link Distance
Ethernet Port
Ethernet Protocols
Power Consumption
Manufacturer
ECOM starter kit
<--->
The H4-ECOM-START gives you everything you need to make your first Ethernet
network simple to build. It contains an
H4-ECOM100 module and instruction manual, a network adapter card
(PCI) for your PC, a crossover cable,
and a Software Product Showcase Demo
CD. The CD contains demo versions
of our software products that support
the ECOM Modules. See the Software
Products section in this catalog for information on the available software packages.
H4-ECOM100
H4-ECOM-F
10/100Base-T Ethernet
10Base-FL Ethernet
100Mbps max.
10Mbps max.
100 meters (328 ft)
2,000 meters (6,560 ft)
RJ45
ST-style fiber optic
TCP/IP, IPX, MODBUS TCP/IP,
DHCP, HTML configuration
TCP/IP, IPX
300mA @ 5VDC
670mA @ 5VDC
Host Automation Products, L.L.C.
H4-ECOM100
The
H4-ECOM100 supports the
Industry Standard Modbus TCP/IP
Client/Server Protocol
H4-ECOM100 IBox
communications
instructions
Over 25 communications IBox instructions are available when using the
H4-ECOM100 with a DL450 PLC and
DirectSOFT5 programming software.
These easy-to-use instructions allow you
to:
• Enable/disable module DHCP
• Read/write module IP, Gateway and
Subnet Mask addresses
• Read/write module ID, Name and
Description
• Send E-mail messages
• Read/Write PLC memory to networked
Hx-ECOM100 modules
• Read/Write PLC memory to networked
Hx-ECOM-F modules
See the following page for example
communications IBox instructions.
Book 1 (14.1)
eD4-30
DL405 PLCs
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Ethernet Communication Modules
Modbus TCP/IP support
Company
Information
Control Systems
Overview
CLICK PLC
Modbus TCP/IP communications architecture
Do-More
PLCs Overview
The H4-ECOM100 supports the industry
standard Modbus TCP/IP Client/Server
protocol in addition to the standard IP
and IPX protocols. This allows the DL405
PLC with an H4-ECOM100 module to
serve as a client (master) or as a server
(slave) on a Modbus TCP/IP Ethernet
network. The H4-ECOM100 can actively
issue Modbus commands to other nodes
or devices on the Modbus TCP/IP network
or simply respond to connected Modbus
TCP/IP clients.
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
DirectLOGIC
DL05/06
DirectLOGIC
DL105
DirectLOGIC
DL205
PLC-to-PLC
communications
PLC-to-PLC or PLC to a Modbus TCP/IP
device communications can be accomplished using standard Read from Network
(RX) and Write to Network (WX) instructions
(DL430/440/450, all H4 series ECOMs
and all DirectSOFT versions). If you’re using
our DirectSOFT5 programming software,
a DL450 PLC and an H4-ECOM100, you
can use fill-in-the-blank IBox instructions
to simplify your communications programming. The H4-ECOM100 supports the
ECOM100 Configuration IBox for use with
the ECRX and ECWX IBox instructions to
read/write to other ECOM(100)s. H4 series
ECOM modules support the NETCFG
Configuration IBox for use with the NETRX
and NETWX IBox instructions to read/
write to other ECOM modules (remember
DL450/DSOFT5 required). The communications IBox instructions execute with built-in
interlocking to greatly simplify communications programming.
Choose your slot
The ECOM modules plug into any I/O slot
of any local DL405 I/O base. The module
maintains identification data, descriptive
information, and communication parameters for PLC-to-PLC communications in
flash memory. Disconnect power before
installing or removing any PLC module.
DirectLOGIC
DL305
ECOM100 Configuration IBox
ECOM100 Read Network IBox
H4-ECOM100 has
e-mail capability!
NetEdit3 software
NetEdit3 Software ships free with the
ECOM User Manual. Use NetEdit3 to
configure the ECOM modules for your
network. Flexible addressing allows
you to use your choice of protocols
and identifying methods. Assign each
module a number or a name or both.
You don’t have to use an IP address,
but you can if it’s necessary for your
network. NetEdit3 uses two protocols for PC-to-PLC communications:
IPX and TCP/IP. The NetEdit3 screen
displays all identifiers and troubleshooting information for each module
on the network. You can use NetEdit3
to adjust parameters for PLC-to-PLC
communications by clicking on
Advanced Settings. The network
identifiers can also be changed from
DirectSOFT Programming Software.
Productivity
Controller
Overview
Productivity
3000
Universal
Field I/O
Software
C-More
HMI
C-More Micro
HMI
ViewMarq
Industrial
Marquees
Other HMI
Communications
Appendix
Book 1
Terms and
Conditions
ECOM100 Send EMail IBox
The H4-ECOM100 Send EMail
(ECEMAIL) IBox instruction will allow the
module to behave as an e-mail client
and send an SMTP request to your SMTP
Server to send a specified e-mail message
to the e-mail addresses in the IBox’s To:
field. The Body: field allows you to embed
real-time data in your e-mail message.
The DL450 CPU and DirectSOFT5 are
required to use the IBox instructions.
Book 1 (14.1)
www.automationdirect.com/dl405
DirectLOGIC
DL405
DL405 PLCs
eD4-31
Prices as of April 16, 2014. Check Web site for most current prices.
Check the Power Budget
Verify your power budget
requirements
This logo is placed next to I/O modules
that are supported by the ZIPLink connection systems.
Your I/O configuration choice can be
affected by the power requirements of the
I/O modules you choose. When determining the types and quantity of I/O
modules you will be using, it is important
to remember there is a limited amount of
power available from the power supply.
See the I/O module specifications at the
end of this section.
The chart on the opposite page indicates
the power supplied and used by each
DL405 device. The adjacent chart shows
an example of how to calculate the power
used by your particular system. These
two charts should make it easy for you to
determine if the devices you have chosen
fit within the power budget of your system
configuration.
Calculating your power
usage
The following example shows how to
calculate the power budget for the DL405
system. The example is constructed around
a single 8-slot base using the devices
shown. It is recommended you construct a
similar table for each base in your system.
A
Base Number
0
Device Type
B
D4-440 CPU
C
Warning: It is extremely important to calculate the
power budget correctly. If you exceed the power
budget, the system may operate in an unpredictable
manner which may result in a risk of personal injury
or equipment damage.
External 24 VDC
Power (mA)
CURRENT SUPPLIED
CPU/Expansion Unit
/Remote Slave
If the I/O you have chosen exceeds the
maximum power available from the power
supply, you can resolve the problem by
shifting some of the modules to an expansion base or remote I/O base (if you are
using remote I/O).
5 VDC (mA)
3700
400
CURRENT REQUIRED
SLOT 0
D4-16ND2
+150
+0
SLOT 1
D4-16ND2
+150
+0
SLOT 2
F4-04DA
+120
+100
SLOT 3
D4-08ND3S
+100
+0
SLOT 4
D4-08ND3S
+100
+0
SLOT 5
D4-16TD2
+100
+0
SLOT 6
D4-16TD2
+100
+0
SLOT 7
D4-16TR
+1000
+0
BASE
D4-08B
+80
+0
Handheld Programmer
D4-HPP
+320
+0
Use ZIPLinks to reduce
power requirements
D
OTHER
If your application requires a lot of relay
outputs, consider using the ZipLink AC
or DC relay output modules. These
modules can switch high current (10A)
loads without putting a load on your base
power budget. Refer to Wiring System for
DL405 PLCs later in this section for more
information.
E Maximum Current Required
2820
100
F Remaining Current Available
3700-2820=880
400-100=300
1. Using a chart similar to the 3one above, fill in column 2.
2. Using the tables on the opposite page, enter the current supplied and used by each device (columns 3 and 4). Pay special attention to
the current supplied by the CPU, Expansion Unit, and Remote Slave since they differ. Devices which fall into the “Other” category (Row D)
are devices such as the Base and the Handheld programmer, which also have power requirements, but do not plug directly into the base.
3. Add the current used by the system devices (columns 3 and 4) starting with Slot 0 and put the total in the row labeled “maximum current required” (Row E).
4. Subtract the row labeled “Maximum current required” (Row E), from the row labeled “Current Supplied” (Row B). Place the difference in
the row labeled “Remaining Current Available” (Row F).
5. If “Maximum Current Required” is greater than “Current Supplied” in either column 3 or 4, the power budget will be exceeded. It will be
unsafe to use this configuration and you will need to restructure your I/O configuration. Note the auxiliary 24 VDC power supply does not
need to supply all the external power. If you need more than the 400mA supplied, you can add an external 24VDC power supply. This will
help keep you within your power budget for external power.
DL405 CPU power supply specifications and power requirements
Specification
Part Numbers
AC Powered Units
D4-450, D4-440, D4-430,
D4-EX (expansion base unit),
D4-RS (remote slave unit)
Voltage Withstand (dielectric)
24 VDC Powered Units
D4-450DC-1, D4-440DC-1,
D4-EXDC (expansion base unit),
D4-RSDC (remote slave unit)
125 VDC Powered Units
D4-450DC-2
D4-440DC-2
1 minute @ 1,500 VAC between primary, secondary, field ground, and run relay
Insulation Resistance
> 10M at 500VDC
Input Voltage Range
85-132 VAC (110 range) 170-264 VAC (220
range
20-28 VDC (24 VDC)
with less than 10% ripple
90-146 VDC (125 VDC)
with less than 10% ripple
Maximum Inrush Current
20 A
20 A
20 A
Maximum Power
50 VA
38 W
30 W
Book 1 (14.1)
eD4-24
DL405 PLCs
1-800-633-0405
Prices as of April 16, 2014. Check Web site for most current prices.
Power Requirements
Company
Information
Control Systems
Overview
CLICK PLC
Power Supplied
CPUs/Remote Units/
Expansion Units
5 VDC Current
Supplied in mA
24V Aux Power
Supplied in mA
CPUs/Remote Units/
Expansion Units
5V Current Supplied
in mA
24VAux. Power
Supplied in mA
D4-430 CPU
D4-440 CPU
D4-440DC-1 CPU
D4-440DC-2 CPU
D4-450 CPU
D4-450DC-1 CPU
D4-450DC-2 CPU
3700
3700
3700
3700
3100
3100
3100
400
400
NONE
NONE
400
NONE
NONE
D4-EX
D4-EXDC
D4-EXDC-2
D4-RS
D4-RSDC
H4-EBC
H4-EBC-F
4000
4000
3700
3700
3700
3470
3300
400
NONE
NONE
400
NONE
400
400
Do-More H2
PLC
Do-More T1H
PLC
DirectLOGIC
PLCs Overview
Power Consumed
Power-consuming
Device
I/O Bases
5V Current
Consumed
D4-04B-1
D4-06B-1
D4-08B-1
80
80
80
External 24VD
Current Required
NONE
NONE
NONE
DC Input Modules
D4-08ND3S
D4-16ND2
D4-16ND2F
D4-32ND3-1
D4-32ND3-2
D4-64ND2
100
150
150
150
150
300 max.
NONE
NONE
NONE
NONE
NONE
NONE
Power-consuming
5V Current
Device
Consumed
Analog Modules (continued)
External 24VDC
Current Required
F4-16AD-1
F4-16AD-2
F4-04DA-1
F4-04DA-2
F4-04DAS-1
F4-04DAS-2
F4-08DA-1
F4-08DA-2
F4-16DA-1
F4-16DA-2
F4-08RTD
F4-08THM-n
F4-08THM
100
100
75+20per circuit
90
60 per circuit
60 per circuit
100+20 per circuit
150
100+20 per circuit
25 max.
NONE
50
60
75
75
70
90
60
60
90
80
90
80
80
120
110
100
150
NONE
NONE
Remote I/O
150
90
NONE
NONE
H4-ERM(100)
H4-ERM-F
D4-RM
DC Output Modules
320(300)
450
300
D4-08TD1
F4-08TD1S
D4-16TD1
D4-16TD2
D4-32TD1
D4-32TD1-1
D4-32TD2
D4-64TD1
150
295
200
400
250
250
350
800
35
NONE
125
NONE
140
140 (15V)
120 (4A max
including loads)
NONE
250
450
NONE
NONE
550
575
575
1000
NONE
NONE
NONE
NONE
Analog Modules
300
670
500
235
NONE
NONE
NONE
NONE
NONE
65
ViewMarq
Industrial
Marquees
Other HMI
Communications
305
Appendix
Book 1
NONE
Specialty Modules
H4-CTRIO
D4-INT
D4-HSC
F4-16PID
F4-8MPI
D4-16SIM
F4-4LTC
400
100
300
160
225
150
280
NONE
NONE
NONE
NONE
170
NONE
75
320
NONE
DV-1000
150
NONE
C-more Micro-Graphic
210
NONE
Programming
D4-HPP-1 (Handheld Prog.)
F4-04AD
F4-04ADS
F4-08AD
Productivity
3000
Terms and
Conditions
Relay Output Modules
D4-08TR
F4-08TRS-1
F4-08TRS
D4-16TR
Productivity
Controller
Overview
C-More Micro
HMI
AC Output Modules
D4-08TA
D4-16TA
DirectLOGIC
DL405
C-More
HMI
CoProcessors
F4-CP128-1
DirectLOGIC
DL305
Software
NONE
NONE
NONE
Communications and Networking
H4-ECOM100
H4-ECOM-F
D4-DCM
F4-MAS-MB
FA-UNICON
DirectLOGIC
DL205
Universal
Field I/O
AC/DC Input Modules
D4-16NE3
F4-08NE3S
DirectLOGIC
DL05/06
DirectLOGIC
DL105
AC Input Modules
D4-08NA
D4-16NA
Do-More
PLCs Overview
150
370
75
100
120
90
Operator Interface
Book 1 (14.1)
www.automationdirect.com/dl405
DL405 PLCs
eD4-25
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement