STM34911306

STM34911306
STEVAL-SPBT2ATV3
USB dongle for the Bluetooth® class 2 SPBT2532C2.AT2 module
Data brief
Features
■
Based on the SPBT2532C2.AT2 class 2
module
■
Bluetooth® specification compliant V2.1+EDR
■
USB interface and power supply
■
Supported reprogrammability via USB
interface
■
SMD antenna and reset button onboard
■
User interface: AT2 command set supporting
data communication with Android smartphone
and Apple iOS Bluetooth® enabled devices
■
RoHS compliant
Description
The STEVAL-SPBT2ATV3 demonstration board is
a design tool to evaluate the SPBT2532C2.AT2
module in a quick and simple way.
The dongle includes the RF antenna and the USB
connector.
The USB connector is used to connect the dongle
to a PC, to access the Bluetooth® module, and to
supply the dongle.
The STEVAL-SPBT2ATV3 includes downloaded
FW, enabling the user to create a Bluetooth® link
with simple AT commands.
The AT command list is detailed in the user
manual UM1547.
The AN3189 application note describes how to
get started with the STEVAL-SPBT2ATV3.
The SPBT2532C2.AT2-based dongle is a
demonstration tool only, to be used strictly for
evaluation purposes. It is not a product in itself.
June 2012
Doc ID 023242 Rev 2
For further information contact your local STMicroelectronics sales office.
1/8
www.st.com
8
Recommended operating conditions
1
STEVAL-SPBT2ATV3
Recommended operating conditions
Table 1.
Recommended operating conditions
Symbol
Parameter
Conditions
Min.
Typ
Max
Unit
VDD
Board supply voltage
-40 °C < T < 85 °C
4
5
6
V
Top
Operating case temperature range
+85
°C
2
I/O connections
2.1
PAD description
-40
Other than the USB plug, some pads are also available. In fact TP1 and TP2 pads make the
SPBT2532C2.AT2 pins available to the user.
Figure 1.
Available pads
Table 2 lists the meaning of these pads.
2/8
Doc ID 023242 Rev 2
STEVAL-SPBT2ATV3
Table 2.
I/O connections
Pad connections
Pads
Description
1
Reset - connected in parallel to onboard reset switch
2
SPBT2532C2.AT2 supply voltage
3
Boot pin - used for firmware downloading - used for testing purposes
4
GPIO01 - general purpose I/O – LED5 is connected to this pin
5
GPIO02 - general purpose I/O – LED4 is connected to this pin
6
GPIO03 - general purpose I/O – LED3 is connected to this pin
7
GPIO04 - general purpose I/O – LED2 is connected to this pin
8
GND
9
GND
10
USB + (5 V)
11
GND
12
Used for testing purposes
13
Used for testing purposes
14
Used for testing purposes
15
Used for testing purposes
16
Used for testing purposes
17
Used for testing purposes
18
3.3 V
TP
2.2
Reset switch
A reset switch SW1 is present on the dongle. When SW1 is pushed SPBT2532C2.AT is
forced to reset.
The following prompt is displayed on the screen:
●
AT-AB - command mode
●
AT-AB BDAddress xxxxxxxxxxxx
Doc ID 023242 Rev 2
3/8
I/O connections
Figure 2.
4/8
STEVAL-SPBT2ATV3
Reset switch
Doc ID 023242 Rev 2
STEVAL-SPBT2ATV3
3
Dongle layout
Dongle layout
Figure 3.
Dongle component layout
Doc ID 023242 Rev 2
5/8
6/8
$17(11$
5
&
1 0
/
S)
10
5
10
'.$?2&
&
10
73
3
Doc ID 023242 Rev 2
73
*3,2
*1'
$17
*1'
*3,2
*3,2
*3,2
9,1
%227
5(6(7
&76
576
5;'
7;'
73
3
3
3
3
3
3
3
73
73
73
9
73 73
5
2KP
6:
6: 386+%87721
*5((1
/('
5
2KP
&
Q
5
.
&
X
9
&
X)
&3
'
9
'
'
*1'
'
,& 86%8):
53"23INTERFACE
'&'
5,
*1'
'
'
9GG
5(*,1
&
Q
5
10
9
,& 1&
1&
6863(1'
6863(1'
1&
567
9%86
3
3
3
3
3
3
%7
73 73 73 73 73 73
37
37
37
37
37
37
1&
&76
576
5;'
7;'
'65
'75
'.$?2&
5
10
73
*1'B5)
10
/('
10
/('
10
/('
73
1&
1&
1&
1&
1&
1&
1&
86%'
86%*1'
86%9FF
86%'
86%&211(&725
-
5
.
Figure 4.
10
5
73
4
10
/('
73
Dongle schematic
STEVAL-SPBT2ATV3
Dongle schematic
Dongle electrical drawing
1567
3$-706
3%-7'2
3%-17567
3$-7',
3$-7&.
%7 02'8/( 63%7&
!-V
STEVAL-SPBT2ATV3
5
Revision history
Revision history
Table 3.
Document revision history
Date
Revision
Changes
11-Jun-2012
1
Initial release.
25-Jun-2012
2
– Title and description modified to improve readability
– Added: Section 1: Recommended operating conditions and
Section 2: I/O connections
Doc ID 023242 Rev 2
7/8
STEVAL-SPBT2ATV3
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2012 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
8/8
Doc ID 023242 Rev 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement