Electralog CS3311 Owner's Manual

Add to My manuals
13 Pages

advertisement

Electralog CS3311 Owner's Manual | Manualzz
Owner’s Manual
Models
CS4416
CS3311
CS2307
CS3311 Pictured
IMPORTANT SAFETY INFORMATION: Always read this manual first
before attempting to install or use this stove. For your safety, always
comply with all warnings and safety instructions contained in this manual
to prevent personal injury or property damage.
7207400100rev06
Table of Contents
Welcome & Congratulations . . . . . . . . . . . . . . . . . . . . . . . . . 3
Important Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Quick Reference Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Compact Stove Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Always use a qualified technician
or service agency to repair
this stove.
! NOTE: Procedures and
techniques that are considered
important enough to
emphasize.
CAUTION: Procedures
and techniques which, if not
carefully followed, will result in
damage to the equipment.
Warning: Procedures
and techniques which, if not
carefully followed, will expose
the user to the risk of fire,
serious injury, or death.
2
Welcome & Congratulations
Thank you and congratulations for
choosing to purchase an electric
stove from Electralog.
Please carefully read and save
these instructions.
CAUTION: Read all
instructions and warnings
carefully before starting
installation. Failure to follow
these instructions may result
in a possible electric shock,
fire hazard and will void
the warranty.
Please record your model and
serial numbers below for future
reference: model and serial
numbers can be found on the
Model and Serial Number labels
of your stove.
NO NEED TO RETURN
TO THE STORE
Questions With the Assembly?
Require Parts Information?
Product Under Manufacturer’s
Warranty?
 Call Toll-Free
1-888-346-7539
Monday to Friday
8:00 a.m. to 4:30 p.m. EST
Please have your model
number and product serial
number ready. (See below)
Serial Number
Model Number
3
Important Instructions
When using electrical appliances,
basic precautions should always be
followed to reduce the risk of fire,
electric shock, and injury to persons,
including the following:
① Read all instructions before using
the Compact Stove.
② The heater is hot when in use.
To avoid burns, do not let bare skin
touch hot surfaces. The trim around
the heater outlet becomes hot during
heater operation. Keep combustible
materials, such as furniture, pillows,
bedding, papers, clothes, and
curtains at least 3 feet (0.9m) from
the front of the unit.
CAUTION: High Temperature.
Keep electrical cords, drapery, and
other furnishings at least 3 feet
(0.9m) from the front of the heater
and away from the side and rear.
③ Extreme caution is necessary
when any heater is used by or
near children or invalids and whenever the unit is left operating
and unattended.
④ Always unplug the Compact
Stove when not in use.
⑤ Do not operate any unit with a
damaged cord or plug, or if the heater
has malfunctioned, or if the Compact
Stove has been dropped or damaged
4
in any manner. Return heater
to authorized service facility for
examination, electrical or mechanical
adjustment, or repair.
⑥ Do not use outdoors.
⑦ The Compact Stove is not
intended for use in bathrooms,
laundry areas and similar indoor
locations. Never locate heater where
it may fall into a bathtub or other
water container.
⑧ Do not run the cord under
carpeting. Do not cover cord with
throw rugs, runners, or the like.
Arrange cord away from traffic area
and where it will not be tripped over.
⑨ To disconnect the unit, turn the
controls off, then remove the plug
from the outlet.
⑩ Do not insert or allow foreign
objects to enter any ventilation or
exhaust opening as this may cause
an electric shock or fire, or damage to
the heater.
⑪ To prevent a possible fire, do
not block air intake or exhaust in any
manner. Do not use on soft surfaces,
like a bed, where openings may
become blocked.
⑫ All electrical heaters have hot
and arcing or sparking parts inside.
Important Instructions
Do not use in areas where gasoline,
paint, or flammable liquids are used
or stored or where the unit will be
exposed to flammable vapors.
⑬ Do not modify the Compact
Stove. Use it only as described in
this manual. Any other use not recommended by the manufacturer
may cause fire, electric shock or
injury to persons.
⑭ To reduce the risk of electric
shock, this appliance has a polarized
plug (one blade is wider than the
other). This plug will fit in a polarized
outlet only one way. If the plug does
not fit fully in the outlet, reverse the
plug. If it still does not fit, contact
a qualified electrician to install the
proper outlet. Do not change the
plug in any way. Avoid the use of an
extension cord. Extension cords may
overheat and cause a risk of fire. If
you must use an extension cord, the
cord must be No. 14 AWG minimum
size and rated no less than 1875
Watts.
⑮ Do not burn wood or other
materials in the Compact Stove.
⑯ Do not strike the clear door
panel.
⑰ Always use a certified electrician
should new circuits or outlets be
required.
⑱ Always use properly grounded,
fused and polarized outlets.
⑲ Disconnect all power supply
before performing any cleaning,
maintenance or relocation of the unit.
⑳ When transporting or storing the
unit and cord, keep in a dry place,
free from excessive vibration and
store so as to avoid damage.
CAUTION
Risk of electric shock
Do not open
No user-servicable parts inside
SAVE THESE Instructions
5
Quick Reference Guide
① Prior to the first use of
the Compact Stove verify the
following:
• Are the circuit breakers for the
unit on?
• Are the light bulbs in your
Compact Stove loose? (To
check, follow the instructions
for replacing the light bulbs under the Maintenance section
of this manual)
② The heater on your Compact
Stove may emit a slight, harmless odor when first used. This odor is
a normal condition caused by the
initial heating of internal heater
parts and will not occur again.
Compact Stove Installation
! NOTE: A 15 Amp, 120
Volt circuit is required. A
dedicated circuit is preferred
but not essential in all cases.
A dedicated circuit will be
required if, after installation,
the circuit breaker trips or
fuses blow on a regular basis
when the heater is operating.
Additional appliances on the
same circuit may exceed the
current rating of the circuit
breaker.
Warning: Ensure the
power cord is not installed so
that it is pinched or against a
6
sharp edge and ensure that
the power cord is stored or
secured to avoid tripping or
snagging to reduce the risk of
fire, electric shock or injury to
persons.
Construction and electrical
wiring must comply with local
building codes and other
applicable regulations to
reduce the risk of fire, electric
shock and injury to persons.
Do not attempt to wire your
own new outlets or circuits. To
reduce the risk of fire, electric
shock or injury to persons,
Compact Stove Installation
always use a licensed
electrician.
① Make sure the unit’s Main On/
Off switch is switched OFF (refer
to operating instruction section).
② Plug the unit into a 15 Amp,
120 VAC outlet. If the cord
does not reach, you may use
an extension cord rated for a
minimum of 1875 Watts.
Operation
Figure 1
A
C
B
A. Main On/Off Switch
The switch has two On positions
marked with “ ” and “Manual”.
The “Manual” position is for
manual operation. In this position
the built-in remote control is bypassed.
The “ ” position is for operating
the unit with the provided remote
control. When in this position
the unit is operated with the ON
and OFF buttons of the remote
control.
When the switch is in the center
“ O ” position the unit is off.
B. Heater On/Off Switch
The Heater On/Off Switch
supplies power to the heater
fan and the heater element.
When the switch is in the on “ I ”
position the heater operates if the
thermostat calls for heat.
C. Heater Thermostat Control
To adjust the temperature to
your individual requirements,
7
Operation
turn the thermostat control
clockwise all the way to turn
on the heater. When the room
reaches the desired temperature,
turn the thermostat knob counter
clockwise until you hear a click.
Leave in this position to maintain
the room temperature at this
setting. For additional heat, turn
clockwise until you hear the click
again and the heater will turn on.
! NOTE: When the heater
is switched on, the heater
fan will operate. The heater
element may or may not be on
depending on the thermostat
control setting (see “Heater
Thermostat Control”).
Resetting the Temperature
Cutoff Switch
Should the heater overheat, an
automatic cut out will turn the
heater off and it will not come
back on without being reset. It
can be reset by switching the
Main On/Off Switch to Off (“ O ”)
and waiting five (5) minutes
before switching the unit back on.
8
CAUTION: If you need to
continuously reset the heater,
unplug the unit and call
Customer Service at
1-888-346-7539.
Remote Operation
The Compact Stove is supplied
with an integrated On/Off remote
control.
! NOTE: Ensure that the
stove's Main On/Off Switch
is set to the remote Control
setting (“
” position).
To operate, push the ON button
to turn stove on, push the OFF
button to turn the stove off.
Battery Replacement
To replace the battery:
• Slide battery cover open on
the hand held transmitter
(Figure 2).
• Correctly install one (1) 12 Volt
(A23) battery in the battery
holder.
• Close the battery cover.
Operation
Figure 2
Battery
Battery Cover
Maintenance
WARNING:
Disconnect
power before attempting any
maintenance or cleaning to
reduce the risk of fire, electric
shock or damage to persons.
Helpful Hints
It is a good idea to replace all
light bulbs at one time if they are
close to the end of their rated life.
Group replacement will reduce
the number of times you need
to open the unit to replace light
bulbs.
Light Bulb Replacement
Allow at least five (5) minutes for
the light bulbs to cool off before
touching to avoid accidental
burning of the skin. Light bulbs
needs to be replaced when you
notice a dark section of the flame
or when the clarity and detail of
the log exterior disappears.
There are two (2) bulbs located
under the Log Set which generate
the flames and embers.
Tools Required: Phillips
screwdriver
9
Maintenance
Light Bulb Requirements
Quantity of two (2) clear
chandelier or candelabra bulbs
with an E-12 (small) socket base,
and 25 Watt rating.
To Replace the Light Bulbs
① Remove the five (5) screws
from the access panel, located on
the back of the unit, and remove
access panel (Figure 3).
Figure 3
Bulbs (2)
Screws
(5)
Clear Door Panel Cleaning
The clear door is cleaned in
the factory during the assembly
operation. During shipment,
installation, handling, etc., the
clear door may collect dust
particles. These can be removed
by dusting lightly with a clean, dry
cloth.
To remove fingerprints or other
marks, the clear doors can be
cleaned with a damp cloth. The
clear door should be completely
dried with a lint free cloth to
prevent water spots.
To prevent scratching, do not use
abrasive cleaners or spray liquids
on the clear door surface.
Compact Stove Surface
Cleaning
Access Panel
② Locate and examine the bulbs
to determine if replacement is
required.
③ Unscrew the bulb(s) counter
clockwise.
④ Insert and install new bulbs.
⑤ Secure access panel to unit.
10 Use warm water only to clean
painted surfaces of the Compact
Stove. Do not use abrasive
cleaners.
Servicing
Except for light bulb replacement
and cleaning described above, an
authorized service representative
should perform any other
servicing.
Warranty
Products to which this limited warranty
applies
This limited warranty applies to the
following models of your newly purchased
Electralog electric stove CS4416, CS3311,
and CS2307. This limited warranty
applies only to purchases made in any
province of Canada except for Yukon
Territory, Nunavut, or Northwest Territories
or in any of the 50 States of the USA (and
the District of Columbia) except for Hawaii
and Alaska. This limited warranty applies
to the original purchaser of the product
only and is not transferable.
Products excluded from this limited
warranty
Light bulbs are not covered by this limited
warranty and are the sole responsibility of
the owner/purchaser. Products purchased
in Yukon Territory, Nunavut, Northwest
Territories, Hawaii, or Alaska are not
covered by this limited warranty. Products
purchased in these States, provinces, or
territories are sold AS IS without warranty
or condition of any kind (including, without
limitation, any implied warranties or
conditions of merchantability or fitness for
a particular purpose) and the entire risk of
as to the quality and performance of the
products is with the purchaser, and in the
event of a defect the purchaser assumes
the entire cost of all necessary servicing
or repair.
material and workmanship for a period of
90 days from the date of the first purchase
of such product.
The limited 90 day warranty period also
applies to any implied warranties that
may exist under applicable law. Some
jurisdictions do not allow limitations on
how long an implied warranty lasts, so
the above limitation may not apply to the
purchaser.
What this limited warranty does not cover
This limited warranty does not apply to
products that have been repaired (except
by Electralog or its authorized service
representatives) or otherwise altered. This
limited warranty does further not apply
to defects resulting from misuse, abuse,
accident, neglect, incorrect installation,
improper maintenance or handling, or
operation with an incorrect power source.
What to do when your unit ceases to
operate as described in this manual
Defects must be brought to the attention of
Electralog Technical Service by contacting
Electralog at 1-888-346-7539, or 1367
Industrial Road, Cambridge Ontario,
Canada N1R 7G8. Please have proof
of purchase, catalogue/model and serial
numbers available when calling. Limited
warranty service requires a proof of
purchase of the product.
What this limited warranty covers and for
how long
What Electralog will do in the event of a
defect
Products covered by this limited warranty
have been tested and inspected prior to
shipment and, subject to the provisions
of this warranty, Electralog warrants
such products to be free from defects in
In the event a product or part covered
by this limited warranty is proven to be
defective in material or workmanship
during the 90 day limited warranty period
you have the following rights:
11
Warranty
• Electralog will in its sole discretion
replace such defective part(s) without
charge, or if part replacement proves
not to be commercially practicable
or cannot be timely made, Electralog
may, in lieu of replacing part(s) choose
to replace the unit.
• This limited warranty does not entitle
the purchaser to on-site or in-home
services. On-site or in-home services
may be performed at the purchaser’s
specific request and expense at
Electralog's then-current rates for such
services.
WITH THE SALE, MAINTENANCE,
USE, OR INABILITY TO USE THE
PRODUCT, EVEN IF Electralog
OR ITS directors, officers, or
AGENTS HAVE BEEN ADVISED OF
THE POSSIBILITY OF SUCH LOSSES,
COSTS OR DAMAGES, OR IF SUCH
LOSSES, COSTS, OR DAMAGES ARE
FORESEEABLE. IN NO EVENT WILL
electralog, or ITS OFFICERS,
DIRECTORS, OR AGENTS BE LIABLE
FOR any DIRECT LOSSES, COSTS,
OR DAMAGES THAT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
• The purchaser is responsible for
removal and transportation of such
product or part (and any repaired or
replacement product or part) to and
from the authorized dealer’s or service
agent’s place of business.
SOME JURISDICTIONS DO NOT ALLOW
THE EXCLUSION OR LIMITATION OF
INCIDENTAL OR CONSEQUENTIAL
DAMAGES, SO THE ABOVE LIMITATION
OR EXCLUSION MAY NOT APPLY TO
THE PURCHASER.
• Electralog will not be responsible for,
and the limited warranty services shall
not include, any expense incurred for
installation or removal of the product
or part (or any replacement product or
part) or any labour or transportation
costs. Such costs shall be the
purchaser’s responsibility.
How State and Provincial law apply
What Electralog and its dealers and
service agents are also not responsible
for:
IN NO EVENT WILL Electralog,
or ITS DIRECTORS, OFFICERS,
OR AGENTS, BE LIABLE TO the
PURCHASER OR ANY THIRD PARTY,
WHETHER IN CONTRACT, IN TORT,
OR ON ANY OTHER BASIS, FOR
ANY INDIRECT, SPECIAL, PUNITIVE,
EXEMPLARY, CONSEQUENTIAL, OR
INCIDENTAL LOSS, COST, OR DAMAGE
ARISING OUT OF OR IN CONNECTION
12 This limited warranty gives you
specific legal rights, and you may
also have other rights which vary
from jurisdiction to jurisdiction. The
provisions of the United Nations
Convention on Contracts for the Sale
of Goods shall not apply to this limited
warranty or the sale of products
covered by this limited warranty.
Warranty
Electralog
1367 Industrial Road
Cambridge ON
Canada N1R 7G8
© 2010 Dimplex North America Limited
Approved for use in the United States and Canada
13

advertisement

Related manuals

advertisement