Model 8455/8465/8475 Air Velocity Transducer

Model 8455/8465/8475 Air Velocity Transducer
AIR VELOCITY
TRANSDUCERS
MODELS 8455,
8465, AND 8475
8455
8465
The 8455, 8465, and 8475 Air Velocity Transducers are ideal for both
temporary and permanent installations for air velocity measurements
in research and development labs, manufacturing processes, and other
applications. The full–scale range, signal output, and time constant are user
selectable and can be easily changed to meet the needs of your application.
Applications
General Purpose (8455)
+ Comfort and draft studies
+ Protected probe tip
+ Critical environment installations (e.g., clean rooms and hospitals)
+ Rugged ceramic sensor
+ Diffuser design analysis
+ Wide range of measurement applications
+ Monitoring drying processes
+ Fast response time
+ Monitoring air flows in tunnels and subways
+ Used as a standard in wind tunnels and calibration facilities
Windowless (8465)
+ Environmental monitoring in greenhouses and IAQ applications
+ Less flow blockage
+ General engineering applications
+ Ideal for measuring in confined spaces
+ Fast response time
Omnidirectional (8475)
+ Omnidirectional probe tip
+ Accurate at low velocities from 10 to 100 ft/min
(0.05 to 0.5 m/s)
+ Ideal for unknown or varying flow direction
UNDERSTANDING, ACCELERATED
8475
SPECIFICATIONS
AIR VELOCITY TRANSDUCERS
MODELS 8455, 8465, AND 8475
Accuracy
8455 8465
8475
±2.0% of reading1,
±0.5% of full scale of selected range
±2.0% of reading1,
±0.5% of full scale of selected range
±3.0% of reading2,
±1.0% of full scale of selected range
Field Selectable Range
8455 and 8465
8475
25 ft/min to 200, 250, 300, 400, 500, 750, 1,000, 1,250, 1,500, 2,000, 2,500, 3,000, 4,000, 5,000, 7,500,
10,000 ft/min (0.125 m/s to 1.0, 1.25, 1.50, 2.0, 2.5, 3.0, 4.0, 5.0, 7.5, 10.0, 12.5, 15.0, 20.0, 25.0, 30.0, 40.0, 50.0 m/s)
10 ft/min to 100, 125, 150, 200, 250, 300, 400, 500 ft/min (0.05 m/s to 0.5, 0.75, 1.0, 1.25, 1.50, 2.0, 2.5 m/s)
All models contain on-board electronics and calibration curves that
provide a linear signal output. This linear signal is sent out as either
a current (mA) or a voltage (V) signal, allowing output to a variety
of data loggers or data acquisition systems. In addition, the current
and voltage output ranges are user-selectable for your convenience.
2.35 in. (6.0 cm)
Cable
16.4 ft (5.0 m)
3.16 in.
(8.0 cm)
4.95 in.
(12.6 cm)
8465/8475
.25 in.
(6.4 mm)
Repeatability
8455 and 8465
<±1.0% of reading3
8475N/A
Response to Flow
8455 and 8465
8475
0.2 sec4
5 sec5
Temperature Range
Compensation
Operating (electronics)
Operating (sensor)
Storage
32 to 140°F (0 to 60°C)
32 to 200°F (0 to 93°C)
32 to 200°F (0 to 93°C)
32 to 200°F (0 to 93°C)
3 in. (7.5 cm), 6 in. (15.0 cm)
9 in. (22.5 cm), 12 in. (30.0 cm)
Voltage mode: less than 1 ohm, 20 mA max source current
Current mode: 500 ohms maximum load
Field selectable 0 to 5V, 0 to 10V,
0 to 20, 2 to 10V, mA, 4 to 20 mA
Field selectable 0.05 to 10 seconds
Probe length
3 in., 6 in., 9 in., 12 in. (7.5 cm, 15 cm, 22.5 cm, or 30 cm)
8455/8465
8475
25 to 10,000 fpm (0.127 10 to 500 fpm (0.05 to
Range
to 50.8 m/s), selectable 2.54 m/s), selectable
±(2% of reading at 64.4 ±(3% of reading at
to 82.4°F (18-28°C)
68.0-78.8°F (20 to 26°C)
Accuracy
+0.5% of full scale of
+1% of full scale of
selected range)
selected range)
5.0 seconds
Response time 0.2 seconds
11 to 30 VDC or 18 to 28 VAC, 350 mA maximum
Input power
From 64.4 to 82.4°F (18 to 28°C), outside this range and within temperature
compensation range add 0.11% per °F (0.2% per °C).
From 68 to 78.8°F (20 to 26°C), outside this range and within temperature compensation
range add 0.28% per °F (0.5% per °C). Directional sensitivity of the Model 8475 is
+5%/-20% of reading +0/-10 ft/min (+0/-0.05 m/s) over 270° solid angle regardless of
flow direction.
3
Standard deviation based on one minute average from 100 to 1,000 fpm (0.5 to 5.0 m/s).
4
For 63% of final value, tested at 1,500 fpm (7.5 m/s).
5
For 63% of final value, tested at 500 fpm (2.5 m/s).
6
Input voltage must be maintained within specifications at the transducer.
1
2
Specifications are subject to change without notice.
TSI and the TSI logo are registered trademarks of TSI Incorporated.
UNDERSTANDING, ACCELERATED
TSI Incorporated - Visit our website www.tsi.com for more information.
Tel: +1 800 874 2811
Tel: +44 149 4 459200
Tel: +33 4 91 11 87 64
Tel: +49 241 523030
P/N 2980575 Rev E
India
China
Singapore
©2012 TSI Incorporated
1.33 in.
(3.4 cm)
3 in. (7.5 cm), 6 in. (15.0 cm)
9 in. (22.5 cm), 12 in. (30.0 cm)
Input Power
11 to 30 VDC or 18 to 38 VAC, 350 mA max6
USA
UK
France
Germany
1.25 in.
(3.2 cm)
8455
.25 in.
(6.4 mm)
Resolution (minimum)
0.07% of selected full scale Output
Impedance
Resistance
Signal Time Constant
0.180 in.
(4.6 mm)
Tel: +91 80 67877200
Tel: +86 10 8251 6588
Tel: +65 6595 6388
Printed in U.S.A.
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement