Canon EF14MM Camera Lens User manual

Add to my manuals
10 Pages

advertisement

Canon EF14MM Camera Lens User manual | Manualzz

EF14mm f/2.8L II USM

COP

Y

ENG

Instruction

Thank you for purchasing a Canon product.

Features

The Canon EF14mm f/2.8L II USM is a highperformance super wide-angle lens designed for EOS cameras.

¡ “USM” stands for Ultrasonic Motor.

1. Aspherical and UD lens elements result in outstanding image delineation.

2. Ultrasonic motor (USM) for fast, quiet focusing.

3. Manual focusing is available after the subject comes into focus in autofocus mode (ONE Y

4. Close-up photography up to 0.2 m/0.7 ft.

5. A truly round aperture hole results in a nicer COP background blur.

6. Tight seal structure ensures excellent dustproof and drip-proof performance.

Conventions used in this instruction

Warning to prevent lens or camera malfunction or damage.

Supplementary notes on using the lens and taking pictures.

ENG-1

a Safety Precautions a Safety Precautions

Do not look at the sun or a bright light source

through the lens or camera. Doing so could result in loss of vision. Looking at the sun directly through the lens is especially hazardous.

Whether it is attached to the camera or not, do not leave the lens under the sun without the

lens cap attached. This is to prevent the lens from concentrating the sun’s rays, which could cause a fire.

Handling Cautions

a warm one, condensation may develop on the

lens surface and internal parts. To prevent condensation in this case, first put the lens into an airtight plastic bag before taking it from a cold to warm environment. Then take out the lens after it has warmed gradually. Do the same when taking the lens from a warm environment into a cold one.

• Do not leave the lens in excessive heat such as in a car in direct sunlight. High temperatures can cause the lens to malfunction.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Do not make any changes or modifications to the equipment unless otherwise specified in the instructions. If such changes or modifications should be made, you could be required to stop operation of the equipment.

This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to part 15 of the FCC

Rules. These limits are designed to provide reasonable protection Y energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Consult the dealer or an experienced radio/TV technician for help.

This Class B digital apparatus complies with Canadian ICES-003.

ENG-2

Nomenclature

Built-in lens hood

Focusing ring (

→ 5)

Focus mode switch ( → 5)

COP

Y

Distance scale ( → 5, 6)

Infrared index ( → 6)

Depth-of-Field scale ( → 6)

Distance index ( → 5)

Gelatin filter holder ( → 7)

Contacts (

→ 4)

Lens mount index ( → 4)

For detailed information, reference page numbers are provided in parentheses (

→ **).

ENG-3

1. Mounting and Detaching the Lens

See your camera’s instructions for details on mounting and detaching the lens.

See the diagrams below for directions for removing and attaching the lens cap.

¡ After detaching the lens, place the lens with the rear end up to prevent the lens surface and electrical contacts from getting scratched.

Y

The lens mount has a rubber ring for enhanced

¡ If the contacts get soiled, scratched, or have fingerprints on them, corrosion or faulty connections can result. The camera and lens

COP water- and dust-resistance. The rubber ring may cause slight abrasions around the camera's lens mount, but this will not cause any problems. If the rubber ring becomes worn, it is replaceable by a may not operate properly.

¡ If the contacts get soiled or have fingerprints on Canon Service Center at cost.

them, clean them with a soft cloth.

¡ If you remove the lens, cover it with the dust cap. To attach it properly, align the lens mount index and the K index of the dust cap as shown in the diagram, and turn clockwise. To remove it, reverse the order.

ENG-4

2. Setting the Focus Mode 3. Infinity Compensation Mark

Infinity compensation mark

Distance index

To shoot in autofocus mode, set the focus mode To compensate for shifting of the infinity focus switch to AF.

To use only manual focusing, set the focus mode switch to MF, and focus by turning the focusing point that results from changes in temperature.

Y point at which the vertical line of the L mark is ring. The focusing ring always works, regardless of the focus mode.

aligned with the distance indicator on the COP

After autofocusing in ONE SHOT AF mode, focus manually by pressing the shutter button halfway and turning the focusing ring. (Full-time manual focus)

For accurate manual focusing on subjects at infinity distance, look through the viewfinder while rotating the focusing ring.

ENG-5

4. Infrared Index 5. Depth-of-Field Scale

The infrared index corrects the focus setting The depth of field is the distance in front of and when using monochrome infrared film. Focus on the subject manually, then adjust the distance setting by moving the focusing ring to the behind the plane of focus on the subject that Y the area between the depth-of-field scale lines corresponding infrared index mark.

Some EOS cameras cannot use infrared film. See below the distance scale. The numbers on the COP shooting distance is 0.5m and the aperture is the instructions for your EOS camera.

f/16, the area in focus will extend from about

0.3m to infinity.

¡ The infrared index position is based on a wavelength of 800 nm.

¡ Be sure to observe the manufacturer’s instructions when using infrared film.

¡ Use a red filter also when you take the picture.

The depth-of-field scale is an approximate indicator.

ENG-6

6. Filter Holder

There is a gelatin filter holder at the rear of the lens. Cut the gelatin filter to fit within the white frames. Then insert the gelatin filter into the filter holder.

¡ Only one filter can be used.

¡ When you use a gelatin filter, ghosting may

COP

Y appear in the image.

ENG-7

Specifications

Image Size

Focal Length/Aperture

Lens Construction

Minimum Aperture

Angle of View

24

× 36 mm

14 mm f/2.8

11 groups, 14 elements f/22

Diagonal: 114° Vertical: 81° Horizontal: 104°

Min. Focusing Distance

Max. Magnification

Field of View

0.2 m / 0.7 ft.

0.15

×

162

× 250 mm / 6.4 × 9.8 inch (at 0.2 m)

Filter

Hood

Case

Insert

Built-in

LP1016

Y

Max. Diameter and Length

Weight

80 × 94 mm / 3.1 × 3.7 inch

645 g / 22.7 oz

COP

¡ The lens length is measured from the mount surface to the front end of the lens. Add 21.5 mm when including the lens cap and dust cap.

¡ The size and weight listed are for the lens only, except as indicated.

¡ The EF1.4X II/EF2X II extender, the EF12 II/EF25 II extension tube, and 250D/500D close-up lenses cannot be used with this lens.

¡ Aperture settings are specified on the camera.

¡ All data listed is measured according to Canon standards.

¡ Product specifications and appearance are subject to change without notice.

ENG-8

COP

Y

CT1-7573-002 © CANON INC. 2007 2009.7

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement