advertisement
OWNER’S MANUAL
MANUAL DE INSTRUCCIONES
DVD PLAYER / Hi-Fi VIDEO CASSETE RECORDER
DVD COMPACTOS / VIDEOGRABADOR Hi-Fi ESTEREO
MVD4540
2A77001AE Cover
ATTENTION
ATENCION
If you purchase a universal remote control from your local retailer, please contact the remote manufacturer for the required programming code.
Si usted a comprado un control remoto universal, por favor comunicace con el fabricante para el codico de programaccion requerido.
TV/CATV MODE SELECTION
SELECCION DE MODO DE TV/CATV
When shipped from the factory, the TV/CATV menu option is set to the "CATV" (Cable
Television) mode.
If not using CATV (Cable TV), set this menu option to the "TV" mode.
Al salir la unidad de fábrica, la opción de menú de TV/CATV se ajusta al modo de
"CATV" (Televisión por cable).
Si no utiliza CATV, ajuste esta opción de menú al modo de "TV".
Before operating the unit, please read this manual thoroughly.
Antes de usar la unidad, lea detenidadmente este manual de instrucciones.
1 8/29/02, 10:52 AM
ENGLISH
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION:
TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR
BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPLI-
ANCE TO RAIN OR MOISTURE.
NOTE:
Please keep all packaging material for at least 90 days in case you need to return this product to your place of purchase or Memorex.
WARNING: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION: Changes or modifications not expressly approved by the partly responsible for compliance with the FCC Rules could void the user's authority to operate this equipment.
CAUTION:
THIS DIGITAL VIDEO PLAYER EMPLOYS A LASER SYSTEM.
TO ENSURE PROPER USE OF THIS PRODUCT, PLEASE READ THIS USER'S GUIDE CAREFULLY AND
RETAIN FOR FUTURE REFERENCE. SHOULD THE UNIT REQUIRE MAINTENANCE, CONTACT AN
AUTHORIZED SERVICE LOCATION-SEE SERVICE PROCEDURE.
USE OF CONTROLS, ADJUSTMENTS OR THE PERFORMANCE OF PROCEDURES OTHER THAN THOSE
SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE.
TO PREVENT DIRECT EXPOSURE TO LASER BEAM, DO NOT TRY TO OPEN THE ENCLOSURE. VISIBLE
LASER RADIATION MAY BE PRESENT WHEN THE ENCLOSURE IS OPENED. DO NOT STARE INTO
BEAM.
Location of the required Marking
The rating sheet and the safety caution are on the rear of the unit.
CERTIFICATION: COMPLIES WITH FDA RADIATION PERFORMANCE
STANDARDS, 21 CFR SUBCHAPTER J.
2
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
L
R
Y
P /C
P /C
R
VIDEO
IN
L
AUDIO
R
CH.
3
OUT
4
2A77001AE(02-05) 2 8/29/02, 10:51 AM
IMPORTANT SAFEGUARDS
1. READ INSTRUCTIONS
All the safety and operating instructions should be read before the unit is operated.
2. RETAIN INSTRUCTIONS
The safety and operating instructions should be retained for future reference.
3. HEED WARNINGS
All warnings on the unit and in the operating instructions should be adhered to.
4. FOLLOW INSTRUCTIONS
All operating and use instructions should be followed.
5. CLEANING
Unplug this unit from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners.
Use a damp cloth for cleaning the exterior cabinet only.
6. ATTACHMENTS
The manufacturer of this unit does not make any recommendations for attachments, as they may cause hazards.
7. WATER AND MOISTURE
Do not use this unit near water. For example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool.
8. ACCESSORIES
Do not place this unit on an unstable cart, stand, tripod, bracket, or table.
PORTABLE CART WARNING
(symbol provided by RETAC)
The unit may fall, causing serious injury, and serious damage to the unit.
8A. An appliance and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn.
9. VENTILATION
Slots and openings in the cabinet back or bottom are provided for ventilation,
S3125A to ensure reliable operation of the unit, and to protect it from overheating.
These openings must not be blocked or covered. The openings should never be blocked by placing the unit on a bed, sofa, rug, or other similar surface. This unit should never be placed near or over a radiator or heat source. This unit should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided and/or the manufacturer’s instructions have been adhered to.
10. POWER SOURCES
This unit should be operated only from the type of power source indicated on the rating plate. If you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. For units intended to operate from battery power, or other sources, refer to the operating instructions.
11. GROUNDING OR POLARIZATION
This unit is equipped with a polarized alternating-current line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug, if your unit is equipped with a 3-wire grounding-type plug, a plug having a third (grounding) pin. This plug will only fit into a grounding-type power outlet. This too, is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet.Do not defeat the safety purpose of the grounding-type plug.
12. POWER-CORD PROTECTION
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance.
3
2A77001AE(02-05) 3 8/29/02, 10:51 AM
4
IMPORTANT SAFEGUARDS
13. LIGHTNING
To protect your unit from a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the unit due to lightning and power line surges.
14. POWER LINES
An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits, as contact with them might be fatal.
15. OVERLOADING
Do not overload wall outlets and extension cords, as this can result in a risk of fire or electric shock.
16. OBJECT AND LIQUID ENTRY
Do not push objects through any openings in this unit, as they may touch dangerous voltage points or short out parts that could result in fire or electric shock. Never spill or spray any type of liquid into the unit.
17. OUTDOOR ANTENNA GROUNDING
If an outside antenna or cable system is connected to the unit, be sure the antenna or cable system is grounded to provide some protection against voltage surges and built-up static charges, Section 810 of the
National Electrical Code, ANSI/NFPA 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.
18. SERVICING
Do not attempt to service this unit yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.
19. DAMAGE REQUIRING SERVICE
Unplug this unit from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. When the power-supply cord or plug is damaged.
b. If liquid has been spilled, or objects have fallen into the unit.
c. If the unit has been exposed to rain or water.
d. If the unit does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions, as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the unit to its normal operation.
e. If the unit has been dropped or the cabinet has been damaged.
f . When the unit exhibits a distinct change in performance, this indicates a need for service.
20. REPLACEMENT PARTS
When replacement parts are required, be sure the service technician uses replacement parts specified by the manufacturer or those that have the same characteristics as the original part.
Unauthorized substitutions may result in fire, electric shock or other hazards.
21. SAFETY CHECK
Upon completion of any service or repairs to this unit, ask the service technician to perform safety checks to determine that the unit is in proper operating condition.
22. WALL OR CEILING MOUNTING
The product should be mounted to a wall or ceiling only as recommended by the manufacturer.
23. HEAT
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
24. DISC TRAY
Keep your fingers well clear of the disc tray as it is closing. It may cause serious personal injury.
25. CONNECTING
When you connect the product to other equipment, turn off the power and unplug all of the equipment from the wall outlet. Failure to do so may cause an electric shock and serious personal injury. Read the owner's manual of the other equipment carefully and follow the instructions when making any connections.
2A77001AE(02-05) 4 8/29/02, 10:51 AM
IMPORTANT SAFEGUARDS
/ Power Source
26. LASER BEAM
Do not look into the opening of the disc tray or ventilation opening of the product to see the source of the laser beam. It may cause sight damage.
27. DISC
Do not use a cracked, deformed, or repaired disc. These discs are easily broken and may cause serious personal injury and product malfunction.
28. NOTE TO CATV SYSTEM INSTALLER
This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.
EXAMPLE OF ANTENNA GROUNDING AS PER THE
NATIONAL ELECTRICAL CODE
ANTENNA LEAD IN WIRE
GROUND CLAMP ANTENNA
DISCHARGE UNIT
(NEC SECTION 810-20)
ELECTRIC SERVICE
EQUIPMENT
GROUNDING CONDUCTORS
(NEC SECTION 810-21)
GROUND CLAMPS
POWER SERVICE GROUNDING
ELECTRODE SYSTEM
(NEC ART 250, PART H)
NEC-NATIONAL ELECTRICAL CODE
S2898A
CONDENSATION
Moisture will form in the operating section of the DVD/VCR if the player is brought from cool surroundings into a warm room or if the temperature of the room rises suddenly. When this happens, the DVD/VCR's performance will be impaired.
To prevent this, let the DVD/VCR stand in its new surroundings for about an hour before switching it on, or make sure that the room temperature rises gradually.
Condensation may also form during the summer if the DVD/VCR is exposed to the breeze from an air conditioner. In such cases, change the location of the DVD/VCR.
Power Source
Wider Hole and Blade
AC Outlet
Polarized AC Cord Plug
(One blade is wider than the other.)
2A77001AE(02-05) 5
TO USE AC POWER SOURCE
Use the AC polarized line cord provided for operation on AC. Insert the AC cord plug into a standard 120V 60Hz polarized AC outlet.
NOTES:
• Never connect the AC line cord plug to other than the specified voltage (120V 60Hz). Use the attached power cord only.
• If the polarized AC cord does not fit into a non-polarized AC outlet, do not attempt to file or cut the blade. It is the user’s responsibility to have an electrician replace the obsolete outlet.
• If you cause a static discharge when touching the unit and the unit fails to function, simply unplug the unit from the AC outlet and plug it back in. The unit should return to normal operation.
5
8/29/02, 10:51 AM
Features
DVD/CD Player/Video Cassette Recorder
• DVD/CD player with Video Cassette Recorder - Unique space saving design combines a DVD/CD player and a Hi-Fi Video cassette recorder. The DVD disc has much more capacity, but is the same size as the audio CD disc. Picture quality is higher than Super VHS. Audio quality is higher than audio CD. The DVD PLAYER can play back audio CDs.
• High Quality Picture - More than 500 lines (VCR mode: 230 lines) of Horizontal Resolution. It exceeds Super VHS (400 lines) or Laser Disc (430 lines) in resolution.
VCR Section
• Stereo/SAP Reception - This VCR is designed to receive stereo and separate audio program (SAP) broadcasts where available.
• 4 Video Heads - Provides optimal picture quality for special effects playback.
• 19
µ
m HEAD - For superior picture quality even in SLP mode, 19micron width technology helps to avoid crosstalk and boost SLP picture quality to near SP levels. With precision technology, ghosts and color beats are virtually eliminated.
• Hi-Fi Stereo Sound - With a frequency response of 20 to 20,000 Hz and a dynamic range of better than 90dB, this VCR provides a level of excellence that rivals compact discs.
• One-touch Timer Recording (OTR) - Simply by pressing the REC/OTR button, the VCR can be programmed for up to 5 hours of recording with an immediate start.
DVD Section
• Compatible with a wide range of DVD audio outputs
Digital Audio Jack (Optical or Coaxial):
• When a component with a built-in Dolby Digital decoder is connected, Dolby Digital sound can produce the effect of being in a movie theater or a concert hall.
• DTS is a surround sound standard different from Dolby Digital. This format is already in use at many theaters. By connecting this unit to a DTS decoder or an AV amplifier with a built-in DTS decoder, the DTS audio of DVD discs recorded in this format can be enjoyed. However, audio will not be output from the analog audio output jacks.
• The MPEG audio of DVD discs recorded in this format can be enjoyed.
• The Linear PCM sound of a 48 kHz/16 bit through 96 kHz/20 bit exceeds audio CD sound.
• Multi-Language - Since this DVD matches with 136 language-subtitles/-soundtracks, you can enjoy selecting a favorite one. (You can not select the language that is not recorded on the disc.)
• Multi-Angle - Pictures of Sports or a Live Concert are recorded with many cameras. When you play such a disc, you can change the angles during playback. (If a Multi-Angle is not recorded on the disc, you can not change the angle.)
• Repeat Playback - You can repeat chapter, track, title, sides or material between two selected points.
• Memory/Random Playback - You can play back tracks, titles or chapters in programmed or random-selected sequences.
• Zoom - You can zoom in on the selected subject on the screen during playback.
• Video Aspect Ratio - You can change the aspect ratio of the screen for your monitor/television on a suitable disc.
• Parental Control - You can limit the playback of scenes or sounds of adult DVD discs which have a parental level rating.
6
* This product incorporates copyright protection technology that is protected by method claims of certain U.S. patents and other intellectual property rights owned by Macrovision Corporation and other rights owners. Use of this copyright protection technology must be authorized by Macrovision Corporation and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision Corporation. Reverse engineering or disassembly is prohibited.
* Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby
Laboratories. Confidential unpublished works. © 1992-1997 Dolby Laboratories, Inc. All rights reserved.
* “DTS” and “DTS Digital Out” are trademarks of Digital Theater Systems, Inc.
* Unauthorized recording of copyrighted television programs, films, video cassettes and other materials may infringe the rights of copyright owners and be contrary to copyright laws.
2A77001AE(06-11) 6 8/29/02, 10:48 AM
Before using your unit
IMPORTANT SAFEGUARDS .......................... 3
Power Source ................................................... 5
Features ........................................................... 6
Contents ........................................................... 7
Parts and functions .......................................... 8
Display ............................................................. 9
Remote control ............................................... 10
Basic connections .......................................... 12
CATV (CABLE TV) connections ..................... 14
Playback connection ...................................... 16
Setting up the VCR section
Setting the video channel ............................... 18
Setting the language ...................................... 18
Auto clock setting ........................................... 19
Manual clock setting ....................................... 21
Tuner setting ................................................... 22
To ADD/DELETE channels ............................ 23
Noise elimination ............................................ 23
Loading and Unloading a cassette tape ......... 24
Tape playback operation
Cassette tape playback .................................. 25
Special playback ............................................ 26
ZERO RETURN function ................................ 27
Video index search system ............................ 27
Recording
Recording a TV program ................................ 28
One-touch Timer Recording (OTR) ................ 30
Timer recording .............................................. 31
Advanced function of VCR section
Stereo recording and playback ...................... 33
Separate Audio Program (SAP) ..................... 33
Duplicating a video tape ................................. 34
Contents
Disc playback operation
Disc ................................................................ 35
Setting setup language .................................. 36
Playback procedure ........................................ 37
Special playback ............................................ 38
Zooming ......................................................... 39
Repeat playback ............................................. 40
Memory playback/Random playback ............. 41
MP3 playback ................................................. 42
Changing soundtrack language ..................... 43
Changing subtitles language .......................... 43
Changing angles ............................................ 44
Title selection ................................................. 44
DVD menu ...................................................... 44
Advanced function of DVD section
Parental control .............................................. 45
Setting menu language .................................. 47
Setting subtitle language ................................ 48
Setting audio soundtrack language ................ 49
Setting the aspect ratio of TV screen ............. 50
Setting on screen display ............................... 51
Setting Audio .................................................. 52
Setting Operation ........................................... 53
Setting Background ........................................ 54
Setting Screen Saver (DVD only) ................... 54
Setting initial setup ......................................... 55
Output sound conversion table ....................... 55
Status display of disc ..................................... 56
Table of languages ......................................... 57
Additional information
Problems and troubleshooting ....................... 58
Video head cleaning ....................................... 59
Specifications ................................................. 60
8/29/02, 10:48 AM
7
2A77001AE(06-11) 7
Parts and functions
Front
VCR/DVD mode selector button
Cassette Loading Slot OPEN/CLOSE button
EJECT button
PLAY button
STOP button
Disc tray
POWER
VIDEO IN L - AUDIO IN - R
VCR CHANNEL VCR/DVD
DVD
VCR
DVD
POWER button
AUDIO (L/R)/
VIDEO IN jacks
CHANNEL
VCR indicator
/ buttons
Display window
Remote sensor DVD indicator
REW (Rewind) button REC button
FF (Fast Forward) button
Rear
AC power cord
DVD OPTICAL
DIGITAL AUDIO
OUT jack (dust protection cap)
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
Y
L
R
P
B
/C
B
DVD COAXIAL DIGITAL
AUDIO OUT jack
DVD AUDIO (L/R) OUT jacks
DVD S-VIDEO OUT jack
P
R
/C
R
IN
VIDEO
L
AUDIO
R
CH.
3
OUT
4
RF IN jack
RF OUT jack
3/4 Channel Selector Switch
DVD/VCR common AUDIO (L/R)/VIDEO OUT jacks
DVD COMPONENT OUT jacks
8
2A77001AE(06-11) 8 8/29/02, 10:48 AM
Display
Display window
1 2 3 4
11 5
6
10 9 8 7
No.
Display
4
5
6
1
2
3
VCR
7
DVD
CD
PM
10 : 00
01 : 00
2
C002
C036
L
10
11
8
9
TRK
REC
Description
VCR mode
Playback (lights) / Auto resume (flashes)
Still picture
DVD disc is inserted.
CD is inserted.
Display for afternoon (not lit during morning hours)
Clock display (colon[ : ] flashes)
Counter display by hour/minute at VCR/DVD / by minute/second at CD
Track number display for CD
TV channel display for VCR
CATV channel display
External input display
Timer recording display
Video tape is in the unit
Track display for CD
Normal recording display (flashes during One-touch Timer Recording - OTR)
Note:
Some discs may be displayed wrong or e.g. chapter number, playback time, etc. may not be displayed.
8/29/02, 10:48 AM
9
2A77001AE(06-11) 9
Remote control
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
POWER
EJECT
OPEN/CLOSE
VCR/DVD
Power on/off
Eject a cassette tape
Open or Close the tray
Switch to operate VCR or DVD
Page
18
24
37
18,40
0-9 Direct channel selection of TV
Input setting
23,28
41
DISPLAY/CALL
Enter a password
Display VCR or DVD operation status
45
29,56
INPUT SELECT Switch the connected TV to external mode 34
CH / Select channel of the connected TV or VCR
28,30
/ Cursor buttons
TRACKING/SET –/+ Setting buttons
/
Manual tracking buttons in playback mode
Cursor buttons
SELECT/ENTER Enter information in the menu
DVD MENU
Select option in the menu
Select menu of a DVD disc
SET UP/VCR MENU Display menu of setup
36
31,32
26
18
18
36
44
18,36,45-55
CLEAR/CANCEL Delete Timer program 32
Cancel input data in the setting mode 21,31,39,41
RETURN
ZOOM
TITLE
Remove DVD set up menu
Zoom (for DVD playback)
Select title of a DVD disc
36
39
44
REPEAT A-B Repeat playback between A and B (DVD/CD) 40
AUDIO/AUDIO SELECT Switches sound between mono, stereo and SAP 33
MEMORY
Change sound track language of DVD 43
Arrange the order of titles, chapters or tracks 41
ZERO RETURN Stop the tape when the counter reaches 00:00 27
ANGLE Change playback angle of a DVD disc
COUNTER RESET Reset the counter to 00:00
44
27
CLOCK/COUNTER Change the front Display mode
TIMER REC
27
Set the unit to start recording at a preset time. 31,32
SUB TITLE
ATR
PLAY MODE
SPEED
Set Subtitle of a DVD disc
Digital AUTO TRACKING
Select playback mode
Sets the tape speed for recording
43
26
40,41
28,30
TV/VCR
REW/SEARCH
Switches between TV and VCR
Rewind/Review playback
18,29
25,26,38
PLAY Playback 25,37
F.FWD/SEARCH Fast Forward/Forward search playback 25,26,38
SKIP /
INDEX /
Skip chapter to forward or reverse direction
Search for the INDEX mark of a tape
38
27
STOP
REC/OTR
SLOW
PAUSE/STILL
Stop
Recording
Slowmotion playback
25,37
28,30,34
26,38
Still picture/Recording pause on/off 26,29,34,38
10
2A77001AE(06-11) 10 8/29/02, 10:48 AM
Inserting Batteries
1
Open the battery compartment cover in the direction of the arrow.
Remote control
2
Install two "AAA" batteries (not supplied), paying attention to the polarity diagram in the battery compartment.
3
Replace the compartment cover.
Battery precautions
The precautions below should be followed when using batteries in this device:
1. Use only the size and type of batteries specified.
2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment.
Reversed batteries may cause damage to the device. To avoid a potential short circuit, insert the “–” end first.
3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones.
4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage.
5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions.)
Remote control basics
• Press POWER to turn the DVD/VCR on or off.
• Make sure VCR/DVD switch is set to VCR/DVD.
• Tap CH or CH to move through the channels one channel at a time.
• The CH / and SET +/– are also used to navigate on-screen menu system.
• You can directly access specific channels using Number keys pad.
• Each press of VCR/DVD on the remote control, switches the screen between the VCR screen (VCR mode) and the DVD screen (DVD mode).
Operation
• Aim the remote control at the remote sensor and press control buttons to operate.
• Operate the remote control within 30
°
angle on either side of the remote sensor, up to a distance of Approx. 5 meters.
Approx. 5 meters
2A77001AE(06-11) 11 8/29/02, 10:48 AM
11
Basic connections
If you are using an antenna system, follow these instructions. If you are a cable (CATV) subscriber,skip ahead to page 14 for the proper connections.
ANTENNA TO DVD/VCR CONNECTION
The DVD/VCR must be connected "between" the antenna and the TV. First, disconnect the antenna from the TV and connect it to the DVD/VCR. Then connect the DVD/VCR to the TV. Below are 3 common methods of connecting an antenna system to a DVD/VCR. Find the type of antenna system you are using and follow the connection diagram.
Combination VHF/UHF Antenna with 75 ohm Coaxial Cable
1
DVD/VCR
75 ohm Coaxial Cable
IN
(ANT.)
OUT
(TV)
2
Combination VHF/UHF Antenna with 300 ohm Twin Lead (Flat) Wire
DVD/VCR
Matching Transformer
300 ohm Input
75 ohm output
(not supplied)
300 ohm Twin Lead (Flat) Wire
IN
(ANT.)
OUT
(TV)
3
DVD/VCR
Separate VHF and UHF Antennas
VHF
UHF
Combiner
75/300 ohm Inputs
75 ohm output
(not supplied)
300 ohm Twin Lead (Flat) Wire
IN
(ANT.)
OUT
(TV)
75 ohm Coaxial Cable
NOTE: If both VHF and UHF antennas have 300 ohm twin lead (flat) wires, use a combiner having two 300 ohm inputs and one 75 ohm output.
NOTES: • A clear picture will not be obtained by the DVD/VCR unless the antenna signal is good. Connect the antenna to the DVD/VCR properly.
• For better quality recording, an indoor antenna or a telescopic antenna is not recommended. The use of an outdoor type antenna is required.
• If you are not sure about the connection, please refer to qualified service personnel.
12
2A77001AE(12-15) 12 8/29/02, 11:03 AM
Basic connections
DVD/VCR TO TV CONNECTION
After you have connected the antenna to the DVD/VCR, you must connect the DVD/VCR to the TV.
Below are 3 common methods of connecting your DVD/VCR to a TV. Find the type of TV you are using and follow the connection diagram.
This DVD/VCR has a single 75 ohm output for connection to a TV. If your TV has separate VHF and UHF antenna inputs (numbers 2 and 3 below), use a splitter to connect the DVD/VCR to the TV for VHF and UHF reception.
75 ohm Coaxial Cable (supplied)
TV
VHF/UHF IN
NOTE: If a VHF or UHF antenna is used, set the TV/CATV menu option to the "TV" mode.
TV with single 75 ohm VHF/UHF antenna input
75 ohm Coaxial Cable
(supplied)
Splitter
75 ohm Input
75/300 ohm outputs
(not supplied)
75 ohm Coaxial Cable
(supplied)
Splitter
75 ohm Input
300 ohm outputs
(not supplied)
TV
UHF
VHF
NOTE: If a VHF or UHF antenna is used, set the TV/CATV menu option to the "TV" mode.
TV with 300 ohm UHF and 75 ohm VHF antenna inputs
TV
UHF
VHF
NOTE: If a VHF or UHF antenna is used, set the TV/CATV menu option to the "TV" mode.
TV with 300 ohm UHF and 300 ohm VHF antenna inputs
13
2A77001AE(12-15) 13 8/29/02, 11:03 AM
CATV (CABLE TV) connections
Many cable companies offer services permitting reception of extra channels including pay or subscription channels.
This DVD/VCR has an extended tuning range and can be tuned to most cable channels without using a cable company supplied converter box, except for those channels which are intentionally scrambled. If you subscribe to a special channel which is scrambled, you must have a descrambler box for proper reception.
1 DVD/VCR
TV
VHF/UHF
IN (ANT)
Incoming Cable
IN
(ANT.)
OUT
(TV)
ALLOWS: * Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording of one channel while watching another.
DVD/VCR
2
Converter/
Descrambler
Incoming
Cable
IN
(ANT.)
OUT
(TV)
TV
VHF/UHF
IN (ANT)
ALLOWS: * Recording of channels through the converter box
(scrambled and unscrambled).
* Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: * Recording one channel while watching another.
* Using the DVD/VCR tuner to select channels.
NOTE:
To record from converter/descrambler,
DVD/VCR tuner must be tuned to the converter output channel, usually channel 3 or 4.
3
DVD/VCR
Incoming Cable
IN
(ANT.)
OUT
(TV)
Converter/Descrambler
TV
VHF/UHF
IN (ANT)
ALLOWS: * Recording of nonscrambled channels.
* Use of the programmable timer.
* Recording an unscrambled channel while watching any channel selected at the converter box.
PREVENTS: Recording scrambled channels.
NOTE:
If you are playing a tape or using the tuner built into the DVD/VCR, the converter must be set to the video channel output of the DVD/VCR (either
3 or 4).
NOTE: Whenever a Converter/Descrambler box is placed before the DVD/VCR, you must tune the DVD/VCR to the output of the Converter/Descrambler box, usually channel 3 or 4.
14
2A77001AE(12-15) 14 8/29/02, 11:03 AM
CATV (CABLE TV) connections
IMPORTANT: Make sure the TV/CATV menu option is set to the "CATV" mode.
This DVD/VCR cannot receive scrambled programs since it does not contain a descrambler. In order to receive scrambled programs, your existing descrambler must be used. Descrambler boxes are available from cable companies. Consult your local cable company for more information concerning connection to their descrambler equipment. There are many ways to connect your DVD/VCR to a cable system. Below are six common methods of connection.
DVD/VCR
4
Splitter
TV
A/B Switch
VHF/UHF
IN (ANT)
Incoming
Cable
Converter/Descrambler
IN
(ANT.)
OUT
(TV)
A
B
ALLOWS: * Recording of one channel while watching another.
* Using the programmable timer to record only the channel selected at the converter box.
* Recording of all channels through the converter box.
PREVENTS: * Watching scrambled channels while recording another channel.
* Using the DVD/VCR tuner to select channels.
5
DVD/VCR
TV
Splitter
IN
(ANT.)
OUT
(TV)
VHF/UHF
IN (ANT)
Incoming
Cable
Converter/
Descrambler
A/B Switch
A
B
ALLOWS: * Recording of nonscrambled channels.
* Recording of one channel while watching another.
* Watching premium channels through the converter while recording nonscrambled channels.
* Using the programmable timer.
PREVENTS: Recording scrambled channels.
DVD/VCR
6
Converter/
Descrambler
TV
Splitter
Incoming
Cable
Converter/
Descrambler
IN
(ANT.)
OUT
(TV)
A/B Switch
A
B
VHF/UHF
IN (ANT)
ALLOWS: * Recording of all channels through the converter box.
* Recording a scrambled or unscrambled channel while watching another (scrambled or unscrambled) channel.
* Using the programmable timer to record only the channel selected at the converter box.
PREVENTS: Using the DVD/VCR tuner to select channels.
15
2A77001AE(12-15) 15 8/29/02, 11:03 AM
Playback connection
The exact arrangement you use to interconnect various video and audio components to the DVD/VCR is dependent on the model and features of each component. Check the Owner's Manual provided with each component for the location of video and audio inputs and outputs.
Connect to a TV with Audio/Video Output
Use the supplied AUDIO/VIDEO Cord.
DVD/VCR
Audio (L) Output Video Output
TV
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
L Y
R
P /C
P
R
/C
R
VIDEO
IN
L
AUDIO
R
CH.
3
OUT
4
Audio (R) Output
To Video
Input
To Audio (R) Input
To Audio (L) Input
AUDIO/VIDEO Cord (supplied)
Connect to a BS TUNER
Satellite
Antenna
ANT. Input
BS Tuner
VHF/UHF
Antenna
75 ohm Coaxial Cable (not supplied)
DVD/VCR
To ANT. Input
TV
ANT. output
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
L
R
Y
P /C
B
P /C R
VIDEO
L
AUDIO
R
CH.
3
IN
OUT
4
ANT.
Output
Video Output
Audio (L) Output
Audio (R) Output
75 ohm Coaxial
Cable (supplied)
AUDIO/VIDEO Cord (supplied)
To ANT.
Input
Connect to a TV with S-Video
Output
S-Video Cord (not supplied)
DVD/VCR
TV
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
L
R
Y
P /C
B
P /C R
VIDEO
L
AUDIO
R
CH.
3
IN
OUT
4
S-Video Output
Audio (L) Output
Audio (R) Output
To S-Video Input
AUDIO Cord (not supplied)
To Audio (R) Input
To Audio (L) Input
16
2A77001AE(16-21) 16 8/29/02, 11:02 AM
Playback connection
Connect to a Stereo Amplifier with Audio Output
If your TV has a COMPONENT VIDEO IN jack, you can connect the DVD/VCR to the TV with a COMPONENT cable (not supplied) as shown below. COMPONENT VIDEO output jack can send higher quality video signal to a
TV than S-Video output.
To Component
Video Output
DVD/VCR
COMPONENT VIDEO Cord (not supplied)
AUDIO/VIDEO Cord (supplied)
To Audio/Video Output
To Audio/Video Input
To
Component
Video Input
Stereo Amplifier
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
Y
L
R
P /C
P /C
VIDEO
IN
ANT.
L
AUDIO
R
CH.
3
OUT
TV
4
Audio (L) Output
Audio (R) Output
To Audio (L) Input
To Audio (R) Input
AUDIO Cord (not supplied)
TV
Connect to an AV Amplifier with built-in digital surround
If you are using an Amplifier with a built-in digital surround as follows, you can enjoy the various audio systems such as Dolby Digital and DTS by using the Optical or Coaxial Digital Output.
Use this connection to connect an:
• AV amplifier with built-in *Dolby Digital decoder
• AV amplifier with built-in *DTS decoder
DVD/VCR
Video cord (not supplied)
Video Output
To Video
Input
TV
DIGITAL AUDIO
OPTICAL COAXIAL
DVD OUTPUT
AUDIO S-VIDEO COMPONENT
Y
L
R
P /C
P /C
VIDEO
IN
ANT.
L
AUDIO
R
CH.
3
OUT
TV
4
Coaxial digital
Audio Output Coaxial digital cable
(not supplied)
AV Amplifier with built-in various decoder as above
NOTE:
You may connect to a TV with a
Component video cable(not supplied) or
S-Video cable(not supplied) instead of a video cable(not supplied).
Connecting the optical digital cable
You may connect to an AV Amplifier with an Optical digital cable (not supplied) instead of a Coaxial digital cable.
When you connect the optical digital cable (not supplied), remove the dust protection cap from the rear panel.
When not using the optical digital cable, attach the dust protection cap to protect against dust.
•
NOTES:
• The OPTICAL, COAXIAL, DVD AUDIO L/R, S-VIDEO and COMPONENT jacks are useful only for DVD section.
On these connections, VCR functions can not be used and also the VCR MENUs don’t appear.
VHS signal is output only from the composite jack (DVD/VCR VIDEO/AUDIO OUTPUT) and UHF/VHF OUT.
• When you make the connections above, do not set DOLBY DIGITAL to DOLBY DIGITAL or DTS to ON on the AV
Amplifier. If you do, a loud noise will suddenly come out from the speakers, affecting your ears or causing the
• speakers to be damaged.
Caution for the optical digital audio output connector: Do not connect to an amplifier (with an optical digital input connector) which does not contain a Dolby Digital or DTS decoder. Otherwise, any attempt to play DVDs may cause such a high level of noise that it may be harmful to your ears and damage your speakers.
• DTS audio will be output only from the COAXIAL or OPTICAL output. To hear DTS audio, DTS-Decoder is necessary.
When playing DTS-encoded CDs, only noise will be heard from the speakers or analogue stereo outputs.
Some DTS decoders which do not support DVD-DTS interface may not work properly with the unit.
17
2A77001AE(16-21) 17 8/29/02, 11:02 AM
Setting the video channel / Setting the language
Setting the video channel
To view playback of a recorded tape or DVD disk, or to watch a program selected by the VCR's channel selector, the TV must be set to channel 3 or 4 (video channel).
When a TV is connected with the 75 ohm coaxial cable only.
1 Press POWER to turn on the DVD/VCR.
2 Press VCR/DVD to select the VCR mode. The VCR indicator on the front panel will light.
1
4
7
POWER EJECT
2
5
8
3
6
9
CH
OPEN/
CLOSE VCR/DVD
DISPLAY/CALL
INPUT SELECT
0
3 Set the 3/4 Channel selector switch on the rear panel to CH
3 or 4.
4 Turn ON the TV and set to CH 3 or 4 to correspond with the channel selected in step 3.
5 Press TV/VCR to select the VCR position.
The VCR indicator will appear in the display.
6 Select any channel to receive a TV station in your area.
The channel number will appear on the screen for about
4 seconds.
TRACKING/
SET
—
SELECT/
ENTER
TRACKING/
SET
+
For a push-button TV tuner
If CH 3 or 4 corresponding to the video channel cannot be tuned on your TV, proceed as follows: set the VCR 3/4 channel selector and the TV to CH 3 or 4, play back a prerecorded tape and tune the TV to receive a sharp color picture from the video cassette recorder. Refer to your TV owner's manual for details.
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH
INDEX/SKIP
PLAY
STOP
SEARCH/F.FWD
SKIP/INDEX
Setting the language
You can choose from three different languages (English,
French and Spanish) for the on-screen displays.
1
Press VCR MENU,
If you use the unit for the first time and press VCR MENU, instead of the main menu screen on the right the “SYSTEM SET UP” menu screen in step 2 may appear.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP ON OFF
CH SET UP
SYSTEM SET UP
〈
+/-/ENTER/MENU
〉
REC/OTR SLOW PAUSE/STILL
2
Press or to select the
“LANGUAGE” option, then press
ENTER.
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENUñ
NOTES:
• If the unit does not operate properly, or if it does not respond to commands via the unit and/or
the remote control: Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.
• Both the VCR and the DVD have their own menu option (See page 36).
• If no buttons are pressed for more than 60 seconds, the MENU screen will return to normal TV-operation automatically.
18
3
4
Press or to select the desired language: English (ENGLISH),
Spanish (ESPAÑOL) or French
(FRANCAIS), then press ENTER.
Press VCR MENU until the MENU screen is cleared.
2A77001AE(16-21) 18 8/29/02, 11:02 AM
Auto clock setting
The Auto Clock feature enables automatic clock setting and updating, and also automates Time Zone and Daylight Saving Time settings by receiving XDS (Extended Data Service) information carried on the channel signal.
Preparation:
You must set the antenna connection before the AC cord plug is inserted into the AC outlet.
1
4
POWER
2
5
EJECT
3
6
VCR/DVD
DISPLAY/CALL
INPUT SELECT
Auto clock setting
After you set the antenna connection and plug the AC cord into an AC outlet (in that order), you must WAIT 30 MINUTES before turning the power switch to the on position to prevent interference with the Auto
Clock activation function.
After the clock is set automatically, you may have to set the Time
Zone and Daylight Saving Time.
Press POWER to turn on the DVD/VCR after the Auto Clock operation is completed.
7 8 9 0
TRACKING/
SET
Ð
CH
SELECT/
ENTER
CH
TRACKING/
SET
+
•
•
•
When shipped from factory, the AUTO CLOCK option is set to ON position.
If you turn the DVD/VCR on during Auto Clock setting, the clock is not set.
With cable box connection, if the Auto Clock Setting is unsuccessful, please select the PBS channel carrying the XDS information, then turn the DVD/VCR off. After 30 minutes, turn the DVD/VCR on, and if the clock is not set automatically, set the clock manually. (See page 21)
Time Zone setting (STANDARD TIME)
In the rare event that you live within broadcast range of two stations in two different time zones, the DVD/VCR may recognize the wrong station for the AUTO CLOCK set. To correct the situation:
DVD MENU RETURN
TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
REW/SEARCH
INDEX/SKIP
REC/OTR
ZOOM
PLAY
STOP
PLAY MODE/
SPEED
TV/VCR
SEARCH/F.FWD
SKIP/INDEX
SLOW PAUSE/STILL
•
•
•
•
Preparation:
Turn ON the TV.
When a TV is connected with an audio/video cable, select the video input mode on the TV.
When a TV is connected only with an antenna cable, set to the video channel 3 or 4. Then select VCR position with TV/VCR.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
1
Press VCR MENU. The VCR menu screen will appear.
Press or to select the SYSTEM SET UP menu, then press ENTER.
2
Press or to select the
“STANDARD TIME” option, then press ENTER.
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/Ð/ENTER/MENUñ
NOTE:
• After performing the Auto Clock setting, in some cases the clock may display an incorrect time zone. You can
• correct the clock by selecting your
Time Zone setting per the instructions above.
When the clock is not set or you set the clock manually, Time Zone setting is not available.
3 Press or to select your Time
Zone, then press the ENTER.
STANDARD TIME
ATLANTIC
CENTRAL
PACIFIC
HAWAII
AUTO
EASTERN
MOUNTAIN
ALASKA
á+/Ð/ENTER/MENUñ
4
Press VCR MENU until the MENU screen is cleared.
19
2A77001AE(16-21) 19 8/29/02, 11:02 AM
Auto clock setting
Daylight saving time setting
You can set the Daylight saving time automatically or manually.
Preparation:
•
•
•
Turn ON the TV.
When a TV is connected with an audio/video cable, select the video input mode on the TV.
When a TV is connected only with an antenna cable, set to the video channel 3 or 4. Then select VCR position with TV/VCR.
• Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
4
7
1
POWER EJECT
2 3
5
8
6
9
CH
TRACKING/
SET
Ð
SELECT/
ENTER
VCR/DVD
DISPLAY/CALL
INPUT SELECT
0
TRACKING/
SET
+
DVD MENU
ZOOM
CH
RETURN
TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
1
Repeat the step 1 on page 19 and press or to select DAYLIGHT
SAVING TIME, then press ENTER.
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENUñ
2
Press or to select one of the options, then press ENTER.
ON:
OFF: for manual setting
(forward one hour) for manual setting
AUTO:
(back one hour) for automatic setting
(read XDS in the signal)
DAYLIGHT SAVING TIME
ON
OFF
AUTO
á+/Ð/ENTER/MENUñ
When you want to set the Daylight Saving Time manually, on the first Sunday in April you set to “ON”, and on the last
Sunday in October you set to “OFF”.
NOTES:
• When shipped from factory, the DAYLIGHT SAVING TIME option is set to “AUTO” position.
• When the clock is not set, Daylight Saving Time setting is not available.
• When there is no Daylight Saving Time in your area, always select “OFF” position in step 2.
20
2A77001AE(16-21) 20 8/29/02, 11:02 AM
You must set the date and time for timer recordings.
Manual clock setting
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
4
7
1
POWER EJECT
2 3
5
8
6
9
CH
TRACKING/
SET
Ð
SELECT/
ENTER
DISPLAY/CALL
INPUT SELECT
0
VCR/DVD
TRACKING/
SET
+
DVD MENU
ZOOM
CH
RETURN
TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
NOTE:
After a power failure or disconnection of the power, the timer settings will be lost. In this case, reset the present time.
EXAMPLE: Setting the clock to "8:30 AM" March, 23 (SAT), 2002.
1 Press VCR MENU. The VCR menu screen will appear.
2
Press or to select the
“SYSTEM SET UP” menu, then press ENTER.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SET UP
ON OFF
SYSTEM SET UP
3
Press or to select the
“CLOCK SET” option, then press
ENTER.
〈
+/-/ENTER/MENU
〉
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENUñ
4 Press or to set the month, then press ENTER.
MONTH
DAY
3
1 (WED)
YEAR 2000
TIME 12 : 00 AM
〈
+/-/ENTER/CANCEL/MENU
〉
To make corrections any time during the process
Press CANCEL repeatedly until the item you want to change blinks, then press or .
5
Set the day, year and time as in step 4.
MONTH
DAY
3
23 (SAT)
YEAR 2002
TIME 8 : 30 AM
〈
+/-/ENTER/CANCEL/MENU
〉
6
After setting the clock, date and time starts functioning automatically.
8 : 30 AM SAT
21
2A77001AE(16-21) 21 8/29/02, 11:02 AM
Tuner setting
This DVD/VCR is equipped with a channel memory feature which allows channels to skip up or down to the next channel set into memory, skipping over unwanted channels. Before selecting channels, they must be programmed into the DVD/VCR’s memory. In addition to normal VHF and UHF channels, this DVD/
VCR can receive up to 113 Cable TV channels. To use this DVD/VCR with an antenna, set the TV/CATV menu option to the TV mode. When shipped from the factory, this menu option is in the CATV mode.
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
4
7
TRACKING/
SET
—
5
8
6
9
CH
INPUT SELECT
0
TRACKING/
SET
+
TV/CATV selection
1 Press VCR MENU. The VCR menu screen will appear. Press
or to select “CH SET UP”, then press ENTER.
2
Press or to select the “TV/
CATV” option.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
SELECT/
ENTER
〈
+/—/ENTER/MENU
〉
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
3
Then press ENTER to select the
TV or CATV mode. The arrow indicates the selected mode.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
TV - VHF/UHF channels
CATV - CABLE TV channels
〈
+/—/ENTER/MENU
〉
PLAY
4 Press VCR MENU until the menu screen is cleared.
REW/SEARCH SEARCH/F.FWD
INDEX/SKIP STOP SKIP/INDEX
REC/OTR SLOW PAUSE/STILL
Setting channels automatically
The VCR can receive a maximum of 181 channels by presetting the channels into memory.
1 Repeat above step 1 and press
or to select “AUTO CH
MEMORY”.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈
+/-/ENTER/MENU
〉
NOTE:
You can’t select “CH SET UP” if you set the channel to “L”.
2
Then press ENTER.
The auto tuning will start. The channel display will count up and when finished, the screen returns to normal.
CH 002
22
2A77001AE(22-27) 22 8/29/02, 11:01 AM
To ADD/DELETE channels / Noise elimination
To ADD/DELETE channels
You can add the channels you want or delete the channels you do not want manually.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
1
Repeat the step 1 on page 22.
Then press or to select the
“ADD/DELETE” option and press
ENTER.
CH SET UP
TV CATV
AUTO CH MEMORY
ADD/DELETE
〈
+/-/ENTER/MENU
〉
2 To Add or Delete desired channels
1
Press Number keys or / to select a channel number you want to add or delete.
ADD
2
To add channels
Press ENTER until “ADD” appears on the screen to set to add the unmemorized channel.
〈
+/-/0-9/ENTER/MENU
〉
CH 003
To delete channels
Press ENTER until “DELETE” appears on the screen to set to delete the channel from memory. The channel number will blink.
3
3 Press VCR MENU until the menu screen is cleared.
Noise elimination
When you don't want to receive a weak signal broadcast, the
Blue back screen can be obtained by selecting the NO NOISE
BACKGROUND "ON". When the unit is shipped from the factory, the NO NOISE BACKGROUND is set to the "ON".
1
Repeat the steps 1~2 on page 21 and press or to select
“ NO NOISE BACKGROUND” .
2 Press ENTER to select the “ON” position.
SYSTEM SET UP
CLOCK SET
LANGUAGE/IDIOMA/LANGUE
NO NOISE BACKGROUND
AUTO CLOCK
STANDARD TIME
ON OFF
ON OFF
DAYLIGHT SAVING TIME
á+/-/ENTER/MENUñ
3 Press VCR MENU until the menu screen is cleared.
23
2A77001AE(22-27) 23 8/29/02, 11:01 AM
Loading and Unloading a cassette tape
Use only video cassette tapes marked
.
Loading
Push the center of the tape until it is automatically inserted.
Insert the cassette tape with its labeled side facing up and the erase prevention tab positioned at your left.
An inverted cassette tape cannot be inserted.
VCR
Erase prevention tab
Automatic power ON
When you insert a cassette tape the VCR power will turn ON automatically.
Automatic playback
When loading a cassette tape without an erase prevention tab, playback will start automatically.
Unloading
1
Press EJECT on the unit or the Remote.
2
Remove the cassette tape.
Automatic tape eject
This VCR will automatically rewind the tape when the tape has ended. When the tape is rewound to its beginning, the cassette tape will be ejected automatically.
To prevent accidental erasure To record again
Remove the erase prevention tab with a screwdriver.
Cover the hole with a piece of adhesive tape.
Screwdriver
Erase prevention tab Adhesive tape
Tape speed and maximum recording time
Tape Speed
SP (Standard Play)
SLP (Super Long Play)
24
T-160
2-2/3 hours
8 hours
T-120
2 hours
6 hours
Video cassette tape
T-90
1-1/2 hours
4-1/2 hours
T-60
1 hour
3 hours
2A77001AE(22-27) 24 8/29/02, 11:01 AM
T-30
30 minutes
1-1/2 hours
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Cassette tape playback
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
1
Load a prerecorded tape
(When loading a cassette tape without the erase prevention tab, playback will start automatically).
2
To start playback
Press PLAY.
Playback will start.
" " will appear on the screen for about 4 seconds.
To stop playback
Press STOP once.
The tape will stop but remain fully loaded and ready to play.
" " will appear on the screen for about 4 seconds.
To rewind the tape or forward it rapidly
Stop the playback or recording with STOP.
To rewind the tape:
Press REW.
To forward the tape:
Press F.FWD.
NOTES:
• This VCR selects the playback tape speed SP, LP or SLP automatically.
• The Cassette tape and DVD disc can be played back simultaneously. If you press VCR/DVD, the tape playback and DVD playback alternate with each other on the screen.
• When you select the VCR mode during
DVD playback, DVD playback will stop automatically after approx. 5 minutes.
To stop the tape-winding, press STOP. To switch to playback directly (without STOP), press PLAY.
Forward/Reverse picture search mode
When the tape is being wound, you can switch to picture search mode (see next page). To do this, press REW or F.FWD and hold it down. The unit will resume the tape winding as soon as the button is released.
25
2A77001AE(22-27) 25 8/29/02, 11:01 AM
Special playback
Picture Search
Reverse picture search function
Press REW x 1 or x 2 during the playback.
Forward picture search function
Press F.FWD x 1 or x 2 during the playback.
To return to playback: Press PLAY.
SPEED SEARCH TIMES
TAPE SPEED
PICTURE SEARCH SPEED
PRESS ONCE PRESS TWICE
SP (Standard Play) 3 X 5 X
LP (Long Play)
SLP (Super Long Play)
7 X
9 X
9 X
15 X
Still Picture
Press PAUSE during playback. To resume normal playback: Press PLAY.
Slow Motion
During playback press SLOW.
To return to playback: Press PLAY or SLOW.
Slow tracking and vertical lock adjustment
If noise bars appear in the picture during slow motion, press the TRACKING + or – to reduce the noise bars.
If the still picture jitters excessively, press TRACKING
+ or – to stabilize the still picture.
Frame by Frame picture
Press PAUSE during playback.
Press SLOW repeatedly. The picture advances frame by frame.
To return to playback: Press PLAY or PAUSE.
Adjusting tracking condition
Automatic tracking adjustment
Whenever you insert a tape and start playback, automatic tracking starts working and continuously analyzes the signal to enable optimum picture quality during playback.
Manual tracking adjustment
If automatic tracking cannot eliminate noises sufficiently during playback, press TRACKING +/– to eliminate the noises.
“MANUAL TR.” will appear. Press it briefly for a fine adjustment, or press and hold for a coarse adjustment.
• Press ATR to reactivate automatic tracking again.
“AUTO TR.” will appear.
NOTES:
• The audio output is muted during SPEED SEARCH,
STILL, FRAME ADVANCE and SLOW MOTION.
• During picture search mode there will be noise bars which are caused by the system.
• The Special Playback will automatically change to playback after approx. 5 minutes to protect the video tape against excessive wear.
26
Repeat playback
The entire video tape will be played until its end. The tape will then automatically rewind to the beginning and the playback will be repeated.
1
Press SETUP MENU. Press or to select
AUTO REPEAT.
2
Then press ENTER to select [ON] or [OFF].
If [ON] is selected, the playback will be repeated endlessly.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SET UP
ON OFF
SYSTEM SET UP
〈
+/-/ENTER/MENU
〉
3
Press VCR MENU until the menu screen is cleared.
if you press CALL, " " will appear on the screen.
4
To start the playback, press PLAY.
The playback will be repeated endlessly.
To cancel repeat mode:
Follow the above step 1, then press ENTER to select the OFF position. Press VCR MENU to return to the
TV.
2A77001AE(22-27) 26 8/29/02, 11:01 AM
ZERO RETURN function / Video index search system
ZERO RETURN function
This function makes tape-rewinding stop at the counter 00:00:00 position automatically.
•
•
Preparation:
Turn ON the TV and set it to the video input mode.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
1 2 3
DISPLAY/CALL
4
7
5
8
6
9
INPUT SELECT
0
1
Press CALL.
The counter display shows the tape running time during playback or recording.
VCR
8 : 47 AM MON
STEREO SAP
CH 001
00 : 04 : 38 SP
CH
TRACKING/
SET
—
SELECT/
ENTER
TRACKING/
SET
+
2
Press COUNTER RESET at the desired tape position. The counter display will be reset to the "00:00:00" position (e.g. the begining of recording).
VCR
8 : 47 AM MON
STEREO SAP
CH 001
00 : 00 : 00 SP
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
3
Press STOP when playback or recording is finished.
Press ZERO RETURN.
The tape will be rewinded or fast forwarded and automatically stop at the ”00:00:00” position.
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP STOP SKIP/INDEX
REC/OTR SLOW PAUSE/STILL
NOTES for Counter Display:
• If you rewind the tape beyond
“00:00:00”, a minus sign (“–”) will be
• displayed in front of the time.
When you load a tape, the counter will reset to “00:00:00”.
• The counter does not function on nonrecorded (blank) sections of the tape. When you rewind, fast forward or play tapes through blank sections, the counter stops.
NOTES for Video index search system:
•
•
•
•
•
When you record an INDEX mark at the very beginning of the tape, the mark may not be found.
During INDEX search, the tape may stop and begin to play at a slightly different location.
INDEX may not function properly with old or worn out video tapes.
INDEX marks may not be found if it is extremely close to the point where the search began.
In recording, if you stop recording temporarily, the INDEX mark is not recorded on the tape.
The CLOCK/COUNTER-button
Press CLOCK/COUNTER. The clock and tape counter alternate with each other in the display.
VCR
VCR
Video index search system
This function enables you to locate the beginning of any recording made on the VCR.
Recording an INDEX MARK
The Index Search function automatically records an INDEX mark on the tape whenever a recording is initiated.
CH 001
INDEX
Index Search
Press INDEX or during stop or play mode.
For Succeeding programs: Press INDEX .
For Preceding programs: Press INDEX .
(Additional press increases the INDEX NO.
up to 9.)
When the INDEX or is pressed, the unit starts searching the INDEX NO.
selected and finds the portion, then playback starts automatically.
To stop the Index Search, press STOP.
or is displayed
+3
INDEX NO. (up to 9)
27
2A77001AE(22-27) 27 8/29/02, 11:01 AM
Recording a TV program
Recording and viewing the same TV program
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
OPEN/
CLOSE VCR/DVD POWER EJECT
1 2 3
DISPLAY/CALL
1
Load a cassette tape with the erase prevention tab intact.
The VCR will automatically turn on.
INPUT SELECT 4 5 6
7 8 0
TRACKING/
SET
—
9
CH
SELECT/
ENTER
TRACKING/
SET
+
2 Press SPEED to select the desired tape speed SP or SLP.
The tape counter and SP or SLP will appear on the screen for about 4 seconds.
00 : 00 : 00 SP
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
3
Set the TV/CATV option to the appropriate position (See page
22).
TV - VHF/UHF channels
CATV - CABLE TV channels
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH
INDEX/SKIP
REC/OTR
PLAY
STOP
SEARCH/F.FWD
SKIP/INDEX
SLOW PAUSE/STILL
4 Press Number keys or CH / to select the channel to be recorded.
1-9 Press 0 twice and then 1-9 as required. Example: To select 2, Press “002”.
10-12 Press 0 first and then the remaining 2 digits in order from left to right.
Example: Press 012 for “12”.
13-99 Press 2 digits in order.
Example: Press 22 for “22”.
100-125 Press the 3 digits in order.
Example: Press 110 for “110”.
CH 110
NOTES:
• If the erase prevention tab is removed, the tape will eject when REC/OTR is pressed for recording.
• If you wish to watch the DVD playback during the normal recording on VCR, press VCR/DVD to change to DVD mode and perform the DVD playback
(see page 37).
• You can not record disc material in
DVD, Video CD, Audio CD, etc. onto a video tape with this DVD/VCR.
28
VHF/UHF/CATV CHANNELS
TV
VHF
2-13
UHF
14-69
CATV
VHF
2-13
STD/HRC/IRC
14-36 (A) (W)
37-59 (AA) (WW)
60-85 (AAA) (ZZZ)
86-94 (86) (94)
95-99 (A-5) (A-1)
100-125 (100)(125)
01 (5A)
5 Press REC/OTR.
" " will appear on the screen for about 4 seconds and “REC” will appear on the display.
INDEX
CH 110
2A77001AE(28-33) 28 8/29/02, 11:00 AM
Recording a TV program
To stop recording
Press STOP to stop recording.
" " will appear on screen for about 4 seconds.
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
To stop recording temporarily
Press PAUSE/STILL to avoid recording unwanted material. Press again to continue the recording.
" " will appear on screen for about 4 seconds.
NOTES:
• The pause function will be released after 5 minutes to prevent damage to the tape or the VCR. The VCR will change to the STOP mode.
• You can select a recording channel in the recording pause mode.
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
Recording one program while watching another
While the VCR is recording, press TV/VCR to select the TV position.
The “VCR” will go off and recording will continue.
Select the TV channel you want to watch by using the TV channel selector.
NOTE:
Some CATV hookups do not permit viewing one channel while recording another. See pages 14,15.
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Auto Rewind feature
This VCR will automatically rewind the tape when the tape has ended (except during OTR and TIMER REC). It will also eject the tape.
To Display VCR operation Status
Press CALL. The clock, day of the week and more information will be indicated.
While watching TV
DAY OF THE WEEK
CLOCK
STEREO AND
SEPARATE AUDIO
PROGRAM (SAP)
8 : 47 AM MON
STEREO SAP
CH 125 CHANNEL
00 : 00 : 00 SP TAPE SPEED
REAL TIME COUNTER
While operating a tape
8 : 30 AM MON
HI-FI
CH 125
OPERATING
MODE
HI-FI STEREO
AUTO REPEAT
00 : 15 : 12 SP
TAPE IN
To cancel the display: Press CALL until all indicators disappear.
29
8/29/02, 11:00 AM 2A77001AE(28-33) 29
One-touch Timer Recording (OTR)
The One-touch Timer Recording feature provides a simple and convenient way to make a timed recording.
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the VCR mode. (The VCR indicator will light.)
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
Example: One-touch Timer Recording for 30 minutes.
1
Load a cassette tape with the erase prevention tab intact.
The VCR will automatically turn on.
2 Press SPEED to select the desired tape speed SP or SLP.
The tape counter and SP or SLP will appear on the screen for about 4 seconds.
00 : 00 : 00 SP
3
Set the TV/CATV option to the appropriate position (See page
22).
TV - VHF/UHF channels
CATV - CABLE TV channels
4 Press Number keys or CH / to select the channel to be recorded.
CH 110
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
5
Press REC/OTR. Press the button again to stop recording after
30 minutes. Each additional press of REC/OTR will increase recording time as shown in the chart below, up to a maximum of
5 hours. The OTR and recording time will appear on the screen for about 4 seconds. And, REC will keep blinking in the display.
NOTE:
If you wish to watch the DVD playback during the OTR, press DVD/VCR to change to DVD mode and perform the
DVD playback (see page 37).
Press once twice
3 times
4 times
5 times
Recording time Press
NORMAL REC
0:30
6 times
7 times
1:00
1:30
2:00
8 times
9 times
Recording time
3:00
4:00
5:00
NORMAL REC
INDEX
To cancel OTR
Press STOP or turn off the power.
" " will appear on screen for about 4 seconds.
OTR 0 : 30
CH 125
30
2A77001AE(28-33) 30 8/29/02, 11:00 AM
Timer recording can be programmed on-screen with the remote control.
The built-in timer allows automatic unattended recording of up to 8 programs within 1 month.
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT
4 5 6
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
Timer recording
Preparation:
• Press VCR/DVD to select the VCR mode.
Load a cassette tape with the erase prevention tab intact.
• Press the CALL button to verify that the time and date are correct (see pa ge 29 ).
Example: Program a timer recording for the 26th day, channel 125
(CATV), 11:00 - 11:30 PM on timer program number 1 (Tape speed: SLP).
1
Press VCR MENU. Select the
“TIMER REC SET” option , then press ENTER.
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP ON OFF
CH SET UP
SYSTEM SET UP
〈
+/—/ENTER/MENU
〉
2 Press SET + or – to select one of the program line, then press ENTER.
DATE START END CH
—
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
3
Press SET + or – to select the date, then press ENTER.
〈
+/—/ENTER/CANCEL/MENU
〉
DATE
26(SU)
START END CH
NOTES:
• If the clock symbol( ) blinks when the timer recording ended, the TV program has not been completely recorded because of an insufficient tape supply.
Press TIMER REC to cancel the timer program or press EJECT to remove the cassette tape.
• During timer recording standby mode, the VCR mode cannot be selected. To use the VCR, press TIMER REC at first, then press VCR/DVD to change to VCR mode. After you use the VCR, press TIMER REC again to put the VCR
• into timer recording standby mode.
If you press TIMER REC during timer recording, the recording operation will be interrupted. If you press TIMER
REC again within the programmed time,
• the recording operation will start again.
After a power failure or disconnection of the power plug, all programmed recording settings and time display will be lost upon resumption of power.
In this case, reset the clock (see page
21) and reprogram any timer recordings.
〈
+/—/ENTER/CANCEL/MENU
〉
4 Set the start time, end time, channel and tape speed as in step 3.
•
•
NOTES:
Press CANCEL to move cursor backward for correction.
To record from external source set the channel to "L". "L" will appear next to CH
125 (or 69).
5
To enter other programs, repeat step
2 through 4.
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
〈
+/—/ENTER/CANCEL/MENU
〉
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
• To return to the normal screen, press VCR MENU twice.
〈
+/—/ENTER/CANCEL/MENU
〉
6 Press TIMER REC. The clock symbol( ) will appear on the display and the VCR stands by for recording. At the same time, VCR mode will change to DVD mode automatically. You can use DVD even if the VCR is in the Timer recording mode.
If you do not use the DVD, turn the power off.
The timer recording will start at 5 seconds before the time you predetermined.
•
•
NOTES:
If the clock symbol( ) does not appear on the display in spite of the pressing of TIMER REC, the cassette may not have been loaded yet. (see page 24)
If the cassette is ejected in spite of the pressing of TIMER REC, the erase prevention tab of the cassette may have been removed. (see page 24)
31
2A77001AE(28-33) 31 8/29/02, 11:00 AM
Timer-recording
Timer recording special case
Weekly (e.g. WKL-TU: each Tuesday) or daily (e.g.
MO-SA: Monday to Saturday) Timer recording
Follow the procedure of timer recording on the previous page. At picture 3 press SET + or – repeatedly until the desired setting appears. Then press ENTER.
When you press SET – repeatedly, the indicator at
DATE will change as follows, in this case the day is
Friday.
The current day (Friday) SU-SA (Sunday to Saturday)
One month later minus one day
WKL-WE
(Weekly Wednesday)
MO-SA (Monday to Saturday)
MO-FR (Monday to Friday)
WKL-TH (Weekly Thursday)
DATE
WKL-WE
START END CH
〈
+/—/ENTER/CANCEL/MENU
〉
Confirmation / Cancellation of the Timer recording
1
If the Timer has been activated, press TIMER REC to deactivate the Timer. The clock symbol( ) will disappear. Then press VCR/DVD to change to
VCR mode.
2
To confirm Timer program:
At picture 1 on the previous page select the
“TIMER REC SET” option and press ENTER.
Then the timer program list as right will appear on the screen.
DATE START END CH
26(SU) 11:00 PM 11:30 PM 125 SLP
〈
+/—/ENTER/CANCEL/MENU
〉
3
To cancel Timer program:
Press SET + or – to select the unnecessary program, then press
CANCEL to cancel the program.
DATE START END
〈
+/—/ENTER/CANCEL/MENU
〉
CH
—
4
Press VCR MENU repeatedly until the TV-picture appears.
In case Timer programs-overlap
• Do not overlap timer programs as portions of the conflicting programs will be lost. The first recording time has priority over the next recording time as shown in the diagram below.
Program 1
Program 2
Program 3
Recording
Control Settings
8 : 00 9 : 00 10 : 00 11 : 00
Prog.1
Deleted Parts
Non Recorded Portion Parts
Prog.2
Prog.3
NOTES:
• If there are other timer record programs remaining,
TIMER REC must be pressed to reactivate the timer, otherwise the remaining timer record programs will be ignored.
• You cannot confirm the Timer program during timer recording operation.
• You can correct or cancel a programmed setting in program confirm mode.
NOTES:
• The daily/weekly recording can be made continuously until the recording is canceled or the tape
• reaches the end.
During timer recording the automatic rewinding mechanism does not function.
32
2A77001AE(28-33) 32 8/29/02, 11:00 AM
Stereo recording and playback / Separate Audio Program (SAP)
Stereo recording and playback
The VHS Hi-Fi audio system permits high fidelity recording of MTS STEREO TV broadcasts.
1
POWER
2
EJECT
3
OPEN/
CLOSE VCR/DVD
DISPLAY/CALL
When a MTS STEREO broadcast is received, the word STEREO will appear on the screen and the program can be viewed or recorded in stereo.
The Hi-Fi STEREO recording procedure is the same as for normal recordings.
STEREO
NOTE:
When using a CATV system, stereo TV programs may be transmitted over a mono cable channel. In this case the word "STEREO" will not appear and the sound will be in mono.
4 5 6 INPUT SELECT
7
TRACKING/
SET
—
8
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM
9
CH
SELECT/
ENTER
0
TRACKING/
SET
+
TITLE REPEAT A-B
Output selection
When viewing an MTS STEREO TV program, or playing a prerecorded
VHS Hi-Fi STEREO videotape, press AUDIO SELECT to select how the audio will be heard through the speakers. Normally set to the Hi-Fi
STEREO position, this button can be set to the MONO position if the stereo broadcast or videotape audio is of poor quality. The "R" and "L" positions allow the audio from the Right or Left Hi-Fi channel to be heard over both TV speakers. This button has no effect when viewing a MONO videotape or TV program. Each time when you press the button, OUTPUT
SELECTION display appears on the screen for several seconds. Refer to the chart below.
OUTPUT
SELECTION
STEREO
L CH
R CH
MONO
SOUND HEARD ON BOTH
SPEAKERS
STEREO
LEFT CHANNEL AUDIO
RIGHT CHANNEL AUDIO
MONO
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH
INDEX/SKIP
REC/OTR
PLAY
STOP
SEARCH/F.FWD
SKIP/INDEX
SLOW PAUSE/STILL
Separate Audio Program (SAP)
Your VCR is fitted with a SAP broadcast system which enables you to switch to a separate audio program when viewing a selected channel.
This function applies only when the program is broadcast in multi-languages through the SAP broadcast system.
1
Press VCR MENU. Then press or to select "SAP".
2 Then press ENTER to select [ON].
Then press VCR MENU until the
MENU
TIMER REC SET
AUTO REPEAT ON OFF
SAP
CH SET UP
ON OFF menu screen is cleared.
SYSTEM SET UP
〈
+/—/ENTER/MENU
〉
NOTES:
• When playing back a tape that is not recorded in Hi-Fi stereo mode, the
• audio will automatically be monaural.
When listening to a VHS Hi-Fi video tape or MTS broadcast through the
VHF/UHF jack (Audio/Video cord not connected), the sound will be monaural.
Listening to SAP
When the VCR is turned on or a channel selection is made, make certain the letters "SAP" appears on the screen. This means that the
"Separate Audio Program" broadcasting is available.
STEREO SAP
OR
SAP
33
2A77001AE(28-33) 33 8/29/02, 11:00 AM
Duplicating a video tape
Duplicating a video tape
If you connect the VCR to another VCR or camcorder, you can duplicate a previously recorded tape.
Make all connections before turning on the power.
1
Load a blank cassette tape with the erase prevention tab intact into the recording VCR.
Load a previously recorded tape into the playback
VCR or CAMCORDER.
4
Press REC/OTR on the recording VCR, then press
PAUSE/STILL.
2
Press SPEED to select the desired tape speed SP or SLP.
It is recommended that you set the Speed to the
SP mode on the recording VCR for best results.
5
Press PLAY on the playback VCR or CAMCORDER, then press PAUSE/STILL.
6
Release the recording pause and the playback still simultaneously to begin the duplicating process.
3
Press INPUT SELECT to select AUDIO/VIDEO input position. "L" will appear in the display.
Connection with second Video recorder
Playback VCR
Connection with Video camera
Playback Camcorder
To AV Jack
To VIDEO OUT To AUDIO (R) OUT
To AUDIO (L) OUT
AUDIO/VIDEO Cord (supplied)
Recording VCR
Recording VCR
To VIDEO IN To AUDIO (R) IN
To AUDIO (L) IN
To VIDEO IN
To AUDIO (R) IN
To AUDIO (L) IN
AUDIO/VIDEO Cord (not supplied)
For duplicating a previously recorded tape from a camcorder, follow the camcorder manufacturer’s instructions. A typical camcorder dubbing hookup is shown above.
34
2A77001AE(34-39) 34 8/29/02, 10:55 AM
Disc
This unit applies to DVD discs from Region 1 only.
The loaded Disc (DVD, Audio-CD and MP3-CD) will be recognized automatically.
The suitable Disc-formats are: DVD, CD-R and CD-RW.
Some CD-R/RW discs may be incompatible.
Do not play DVD-ROM, DVD-Audio, CDV, Video-CD, CD-G or Photo CD to prevent accidental erasure of prerecorded material.
This unit cannot record disc material in DVD, Audio CD etc. onto a video tape.
If you press the REC/OTR during DVD playback, a symbol mark " seconds.
" will appear on the screen for aprox.4
DVD DISC
TITLE1
CHAPTER 1 CHAPTER 2 CHAPTER 1
TITLE2
CHAPTER 2 CHAPTER 3
Title
When two or more movies are recorded on a disc, the disc is divided into two or more sections. Each section is called a “TITLE”.
Chapter
The titles can be subdivided into many sections.
Each section is called a “CHAPTER”.
Track
An Audio CD can contain several items.
These are assigned to the tracks.
TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5
Removing Disc from Case
Be sure to hold the edge of disc. Do not touch the surface of the disc.
Pick up the disc gently from the case.
• Do not scratch the disc.
• Do not get dirt on the surface of the disc.
• Do not stick a label or adhesive tape on the disc.
• Do not drop or bend the disc.
Storing Disc
• Store the disc in the case to avoid risk of scratches, dirt or damage.
• Do not leave disc exposed to direct sunlight or in hot or humid places.
Cleaning Disc
Wipe the disc with a clean, dry cloth from center to edge.
• Do not wipe the disc round.
• Do not use liquid or aerosol cleaners.
35
2A77001AE(34-39) 35 8/29/02, 10:55 AM
Setting setup language
The setup language can be selected.
•
•
Preparation:
Turn ON the TV and set to the video input mode.
When using an amplifier, switch on the amplifier.
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
1
Press VCR/DVD to select the
DVD mode. (The DVD indicator will light.)
“No Disc” will appear on the screen. (If a DVD disc has already loaded, the playback will start automatically.)
2
Press SET UP in the stop mode.
The SETUP MENU of DVD will appear on the screen.
Then press or to select
“Language”.
Picture
TV Shape 4:3LB
AB C
: Select : Enter
3
Press / to select On-Screen
Language, then press ENTER.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
: Select : Enter
4
Press / to select desired language: English (English),
French (Français) or Spanish
(Español), then press ENTER.
AB C
Language
On-Screen Language ENG
Dsc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
English
Fran ais
Espa ol
: Select : Enter
NOTE: To make the SETUP screen disappear, press SET UP
(or RETURN).
If the DVD/VCR does not operate
properly: Static electricity, etc., may affect the player's operation. Disconnect the AC power cord once, then connect it again.
36
2A77001AE(34-39) 36 8/29/02, 10:55 AM
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
Playback procedure
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
Press OPEN/CLOSE.
The disc tray will open.
INPUT SELECT 4 5 6
7 8 9
CH
0 2 Place a disc onto the tray.
Hold the disc, position it with the printed label side up, align it with the guides, and place it in its proper position.
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
3
Press PLAY or OPEN/CLOSE.
The disc tray closes automatically.
On the screen, changes to
“ ” and then playback will commence.
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
• A menu screen may appear on the TV screen, if the disc has a menu feature. In this case, press , , , or
ENTER to operate a menu feature.
REW/SEARCH
REC/OTR
SEARCH/F.FWD
INDEX/SKIP
PLAY
STOP SKIP/INDEX
SLOW PAUSE/STILL
4
Press STOP to end playback.
• The DVD/VCR memorizes the stopped point, depending on the disc. “To Return To The Last Scene Viewed, Press Play.
To Disable This Operation, Press STOP Again.” appears on the screen for approx. 4 seconds. “ ” will continue blinking in the display until the playback is stopped completely. Press
PLAY to resume playback (from the scene point).
• If you press STOP again (“ ” appears on the screen) or unload the disc, the DVD/VCR will clear the stopped point.
5 Then press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
• If a non-compatible disc is loaded, "Please Check Disc", "Disc playback unauthorized Consult owners manual for further information" or "Parental Lock" will appear on the TV screen according to the type of loaded disc. In this case, check your disc again (See pages 35 and 45).
• Some discs may take a minute or so to start playback.
• A “Prohibition” symbol may appear at the upper right of the screen. This symbol means either the feature you tried is not available on the disc, or the DVD/VCR can not access the feature at this time. This does not indicate a problem with the DVD/VCR.
• When you set a single-faced disc label downwards (ie. the wrong way up) and press PLAY or OPEN/CLOSE,
" " will appear and remain on the screen for approx. 40 seconds and then it will change to "Please Check Disc".
• Some playback operations of DVDs may be intentionally fixed by software producers. Since this DVD/VCR plays
DVDs according to the disc contents the software producers designed, some playback features may not be available. Also refer to the instructions supplied with the DVDs.
• When playing DTS-encoded Audio CDs, excessive noise will be heard from the analog stereo outputs. To avoid possible damage to the audio system, the consumer should take proper precautions when the analog stereo outputs of the DVD/VCR are connected to an amplification system.
37
2A77001AE(34-39) 37 8/29/02, 10:55 AM
Special playback
Note: There may be a slight delay between pressing the button and the function activation.
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
4
7
5
8
6
9
INPUT SELECT
0
CH
TRACKING/
SET
—
DVD MENU
SET UP/
VCR MENU
CLEAR/
CANCEL
TRACKING/
SET
+
RETURN
ZOOM TITLE REPEAT A-B
Fast Forward Playback
Press F.FWD during normal playback.
Each press of F.FWD will increase the speed of the search x2 ( ), x8 ( ), x30 ( ), x100 ( x8 ( ) are available)
). (in case of Audio-CD: x4 ( ) and
• To resume normal playback, press PLAY.
Review Playback
Press REW during normal playback.
Each press of REW will increase the speed of the search x2 ( ), x8
( ), x30 ( ), x100 ( ). (in case of Audio-CD: x4 ( ) and x8
( ) are available)
• To resume normal playback, press PLAY.
Still Playback
Press PAUSE/STILL during normal playback.
To resume normal playback, press
PLAY.
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Frame Advance
Press PAUSE/STILL during still playback.
One frame is advanced each time you press PAUSE/STILL.
To resume normal playback, press
PLAY.
NOTES:
• The unit is capable of holding a still video image or On screen display image on your television screen indefinitely. If you leave the still video image or On screen display image displayed on your
TV for an extended period of time, you risk permanent damage to your television screen. Projection televisions are very susceptible.
• Some titles may not display chapter numbers.
• When you set “Title Stop” to “Off” (See page 53), you can access chapter in another title. If you go back to the preceding title by pressing the SKIP, the
DVD/VCR locates the first chapter of the title. When “Title Stop” is set to “On”.
you can access chapters only within the current title.
38
Slow-motion Playback
Press SLOW during normal playback or still playback.
Each press of SLOW will change the speed of the slow x1/2, x1/4, x1/8.
• To resume normal playback, press PLAY.
• To resume the still playback, press PAUSE/STILL.
Locating a chapter or track
(
Press SKIP ( ) Forward or SKIP
) Reverse during playback to locate a chapter or track that you want to watch.
Each time you press the button, a
“C (chapter)” number or “T (track)” number is skipped.
T 1 C 1
When you press SKIP ( ), playback starts from the beginning of the current chapter or track.
When you press SKIP ( ) twice, playback starts from the beginning of the preceding chapter or track.
2A77001AE(34-39) 38 8/29/02, 10:55 AM
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Zooming
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Zooming
This unit will allow you to zoom in on the frame image. You can then make selections by switching the position of the frame.
1
Press ZOOM during playback.
The center part of the image will be zoomed in.
As you repeatedly press the
ENTER or ZOOM while “ZOOM” is selected, the magnification level changes. Variation of the levels includes image reduction.
ZOOM
EXIT
Zoom Off
: Select : Change
• If you select “EXIT” and press the ENTER, you can turn off the symbol mark, keeping the current magnification level.
2 Press / or / to view a different part of the frame.
You may move the frame from the center position to UP,
DOWN, LEFT or RIGHT direction.
• Press CLEAR to restore the zoom point to the center of the picture.
3
While “ZOOM” is selected, press ZOOM repeatedly to return to a 1:1 view.
2A77001AE(34-39) 39 8/29/02, 10:55 AM
39
Repeat playback
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
NOTES:
• Some discs may not work with the repeat operation.
• In A-B repeat mode, subtitles near point A or B may not appear.
• During the A-B Repeat Playback the
ANGLE feature will not operate.
• You may not be able to set A-B Repeat, depending on the scenes of the
DVD.
• A-B repeat does not work with an interactive DVD and MP3-CD.
• Random playback can not be combined with Repeat playback.
40
2A77001AE(40-45) 40
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
REPEAT PLAYBACK
1 Press PLAY MODE repeatedly to select “Chapter Repeat”,
“Title Repeat” or “ALL Repeat”. (In case of CD, select “Track
Repeat” or “ ALL Repeat”.)
DVD CD
Chapter Repeat Track Repeat
2
During playback repeat playback will start automatically.
During stop mode press PLAY within about 5 seconds after you press PLAY MODE to start repeat playback.
• To resume normal playback, select Off.
A-B Repeat Playback
A-B repeat playback allows you to repeat material between two selected points.
1
Press REPEAT A-B during playback.
The start point is selected.
A-
2
Press REPEAT A-B again.
The end point is selected.
Playback starts at the point that you selected. Playback stops at the end point, returns to Point A automatically, then starts again.
To resume normal playback, press REPEAT A-B again.
“Repeat Off” appears on the screen.
A-B
8/29/02, 11:07 AM
4
7
1
POWER
2
EJECT
3
OPEN/
CLOSE VCR/DVD
Memory playback/Random playback
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Memory playback
You can arrange the order of titles, chapter or tracks on the disc.
DISPLAY/CALL
1
Press MEMORY.
In stop mode In play back
5
8
6
9
INPUT SELECT
0
1 T:- - CT:- - -
2 T:- - CT:- - -
3 T:- - CT:- - -
4 T:- - CT:- - -
5 T:- - CT:- - -
6 T:- - CT:- - -
7 T:- - CT:- - -
Memory
: Select 0-9 : Input : Play
1 T:- - CT:- - -
Memory
: Select 0-9 : Input : Play
TRACKING/
SET
—
CH
SELECT/
ENTER
TRACKING/
SET
+
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH
INDEX/SKIP
REC/OTR
PLAY
STOP
SEARCH/F.FWD
SKIP/INDEX
SLOW PAUSE/STILL
NOTES:
• The memory playback is cancelled when press STOP during memory playback.
• Random playback can not be combined with Repeat playback.
• You can program up to 30 selections into the memory.
• Depending on the DVD, Chapter
Random operation may not work during playback.
• You cannot use the random playback with memory playback.
2
Press / to select “T” or “CT”.
Use Number keys to Input the favorite number.
In stop mode
1 T:01 CT:002
2 T:- - CT:- - -
3 T:- - CT:- - -
4 T:- - CT:- - -
5 T:- - CT:- - -
6 T:- - CT:- - -
7 T:- - CT:- - -
Memory
: Select 0-9 : Input
In play back
1 T:01 CT:002
Memory
: Select 0-9 : Input : Play : Play
T : Title number
CT : Chapter number or track number
• If you input a large number than the number that is recorded on the disc, the bar will be skipped.
• The input number into "T" for CD or MP3 is not effective.
3
Press or ENTER.
Set the “T” and
“CT” to bar that you want to enter as in step 2.
In stop mode
1 T:01 CT:002
2 T:02 CT:004
3 T:- - CT:- - -
4 T:- - CT:- - -
5 T:- - CT:- - -
6 T:- - CT:- - -
7 T:- - CT:- - -
Memory
: Select 0-9 : Input : Play
In play back
2 T:02 CT:004
Memory
: Select 0-9 : Input : Play
• When you select another chapter in the same title, you do not need to select the title number.
• To cancel the programmed selection, press CANCEL.
4
Press PLAY to start MEMORY playback.
• To resume normal playback, press CANCEL.
Random playback
1
Press PLAY MODE repeatedly to select “ Chapter Random” or “Title Random”.(In case of CD, select Track Random)
DVD CD
2
Chapter Random Track Random
During playback random playback will start automatically.
During stop mode press PLAY within about 5 seconds after you press PLAY MODE to start random playback.
• To resume normal playback, select Off.
41
2A77001AE(40-45) 41 8/29/02, 11:07 AM
MP3 Playback
This player can play back the MP3-data which has been recorded on CD-R or CD-
RW. To produce the MP3-data, you need a
Windows-PC with CD-ROM drive and a MP3encoding Software (not supplied).
The Apple-HFS-System can not be played.
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
Press OPEN/CLOSE.
The disc tray will open.
Place a disc onto the tray.
MP3 CD Information
Limitations on MP3 CD playback
• MP3 CD is the disc that is standardized by
ISO9660, its file name must include 3-digits extension letters, “mp3”.
• The directory and file names of the MP3
CD must correspond to the ISO standardized files.
• This unit can read 200 files per disc. If one directory has more than 200 files, it reads up to 200 files, the remaining files will be omitted.
• As for multi-session disc, only the first session can be played.
• If the CD has both audio tracks and MP3 files, only audio tracks are played.
• It may take more than one minute for this unit to read MP3 files depending on its structure.
• Music recorded by “Joliet Recording
Specification” can be played back, the file name is displayed (within 8 letters) on the screen. Long file names will be condensed.
• The music files recorded by “Hierarchical
File System” (HFS) cannot be played.
Limitations on display
• The maximum number for display is 8 letters. Available letters for display are the following: capital or small alphabets of A through Z, numbers of 0 through 9, and _
(under score).
• Other characters than those above are replaced in hyphen.
Notes on MP3 files
To play back MP3 CD in the recorded order,
1. Use MP3 software that records data alphabetically or numerically.
2. Name each file including a two-digit or threedigit number (e.g. “01” “02” or “001” “002”).
3. Refrain from making too many sub-folders.
CAUTION:
• Some MP3 CDs can not be played back depending on the recording conditions.
• The CD-R/RW that has no music data or non-MP3 files can not be played back.
2
Press PLAY or OPEN/CLOSE.
The disc tray closes automatically.
On the TV-screen, “ ” and then reading file number will appear.
Reading will take as much time as the number of file.
3
Press DISPLAY.
Then press / to select
MP3
and press ENTER.
T 11
T 1 000:23
MP3
: Select : Enter
EAM
PCM
4
Press / or / to select the desired track, then press
ENTER. Track is selected and play commences.
• In case the folder includes more than 9 tracks, press /
to display next track list.
• To remove track list, press CANCEL.
• Press / to select “T” and press Number keys your desired to input.
T 1 000:23
MP3
1. \ CRYINI~1
2. \ DANGER~1
3. \ GITARREN
4. \ LILYWA~1
5. \ MERCYS~1
6. \ OBSESS~1
7. \ PINKPA~1
8. \ RUNNIN~1
: Select : Search
5
Press STOP to end playback.
• The unit records the stopped track.
Press PLAY to resume playback (from the beginning of track).
• If you press STOP again or unload the disc, the unit will clear the stopped track.
EAM
PCM
6 Press OPEN/CLOSE.
The disc tray opens.
Remove the disc and press POWER.
The disc tray closes automatically and DVD/VCR turns off.
NOTES:
• During MP3-Playback, you can not use SEARCH, A-B
Repeat functions.
• You can use Repeat(Track or All) and Random functions for
MP3 CD Playback.(See page 40 and 41)
42
2A77001AE(40-45) 42 8/29/02, 11:07 AM
Changing soundtrack language / Changing Subtitles language
•
•
Preparation:
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
OPEN/
CLOSE POWER EJECT VCR/DVD
1
4
2
5
3
6
DISPLAY/CALL
INPUT SELECT
Changing soundtrack language
You can select the language when you play a multilingual disc.
1
Press AUDIO during playback.
The current soundtrack language is displayed.
ENG1
ENG2
FRE1
2CH
5.1CH
2CH 7 8 9 0
TRACKING/
SET
—
CH
SELECT/
ENTER
TRACKING/
SET
+
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
Audio:FRE1
: Select
2CH
: Return
2CH
2 Press AUDIO repeatedly until the desired language is selected.
The on-screen display will disappear after a few seconds.
• To turn off the soundtrack setting display,press the
CLEAR or ENTER.
ENG1
ENG2
FRE1
2CH
5.1CH
2CH
Audio:ENG1
: Select
2CH
: Return
2CH
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
Changing Subtitles language
You can select the language when playing back a disc recorded with multi-lingual subtitles.
1 Press SUB TITLE during playback.
Then press / to select the desired language.
• To turn off the subtitle setting display, press the CLEAR or
ENTER.
• To turn the subtitles off, select
“Off”.
Off
ENG 1
SPA 1
FRE 1
Subtitle:- - - Off
: Select : Return
REW/SEARCH PLAY SEARCH/F FWD
NOTES:
• If the desired language is not heard after pressing AUDIO several times, the language is not recorded on the disc.
• Changing soundtrack or subtitle language is cancelled when you open the disc tray or turn the power off. The initial default language or available language will be heard and seen if the disc is played back again.
• Depending on the DVD you may be unable to turn on, turn off, or change the subtitles, even if they are recorded on the disc. While playing the DVD, the subtitle may change while opening or closing the disc tray, or while changing the title.
• During some scenes, the subtitles may not appear immediately after you select “On”.
• The abbreviation of the language appears instead of the language name.
Refer to the list of languages and their abbreviations. (See on page 57.)
2
Press SUB TITLE or / to turn Subtitles on or off.
Off
ENG 1
SPA 1
FRE 1
Subtitle:ENG1 On
: Select : On/Off : Return
43
2A77001AE(40-45) 43 8/29/02, 11:07 AM
Changing angles / Title selection / DVD menu
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
NOTE:
Depending on the DVD, you may not be able to change the angles even if multi-angles are recorded on the disc, or you may be unable to select the title, and a “title menu” may simply be called a “menu” or “title” in the instructions supplied with the disc.
Changing Angles
When playing back a disc recorded with multi-angle facility, you can change the angle that you are viewing the scene from.
1
Press ANGLE during playback.
The current angle will appear.
1
2
3
Angle :1
: Select : Return
2
Press ANGLE or / repeatedly until the desired angle is selected.
• To turn off the angle number display, press the CLEAR.
• You can change the camera angle directly by pressing the
number keys corresponding to its angle number instead of
using the / .
Title Selection
Two or more titles are recorded on some discs. If the title menu is recorded on the disc, you can select the desired title.
1
Press TITLE during playback.
Title menu appears on the screen.
• Press TITLE again to resume playback at the scene when you pressed TITLE.
2
Press / or / to select the desired title.
3
Press ENTER or PLAY.
The playback of the selected title will start.
DVD Menu
Some DVDs allow you to select the disc contents using the menu.
When you play back these DVDs, you can select the subtitle language and sound-track language,etc. using the DVD menu.
1
Press DVD MENU during playback.
The DVD menu appears on the screen.
• Press DVD MENU again to resume playback at the scene when you pressed DVD MENU.
2
Press / or / to select the desired item.
3
Press ENTER.
The menu continues to another screen. Repeat steps 2 and 3 to set the item completely.
44
2A77001AE(40-45) 44 8/29/02, 11:07 AM
Some discs are specified not suitable for children. Such discs can be prevented from play back with the unit.
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Parental control
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Parental control setting
1
Press SET UP in the stop mode.
Press or to select “Operation”.
Picture
TV Shape 4:3LB
AB C
: Select : Enter
2
Press or to select “Parental Lock”, then press ENTER.
AB C
Operation
Pause/Still
Parental Lock
Title Stop
Auto
Off
Off
Off
On
: Select : Enter
3
Press or to select Off or On.
Off: The parental lock feature does
AB C not function.
Operation
Pause/Still
Parental Lock
Title Stop
Auto
Off
Off
Off
On
After pressing the ENTER, follow step 4 below.
: Select : Enter
On: To activate the parental lock feature or change the setting, press the ENTER button and follow steps 4-6 below.
4
Press Number keys to input a 4-digits password then press the ENTER button.
• If you input a wrong number, press
CANCEL.
AB C
Operation
Pause/Still
Parental Lock
Title Stop
Auto
Off
Off
Off
On
Security Code ----
: Select : Enter
NOTES:
•
•
•
•
If each setup (page 45~55) has been completed, the unit can always be worked under the same conditions
(especially with DVD discs).
Each setup will be retained in the memory if you turn the power off.
Depending on the discs, the unit cannot limit playback.
Some discs may not be encoded with specific rating level information though its disc jacket says "adult". For those discs, the age restriction will not work.
Do not forget the password. If you forget the password, contact customer service.
5
Enter the code of a country/area whose standards were used to rate the DVD disc. (See the list on the page 46.)
AB C
Operation
Pause/Still
Parental Lock
Title Stop
Auto
Off
Off
Off
On
Area Code U S
: Select : Enter
45
2A77001AE(40-45) 45 8/29/02, 11:08 AM
Parental control (Continued)
1
4
7
POWER
TRACKING/
SET
Ð
2
5
8
EJECT
3
6
9
CH
DISPLAY/CALL
INPUT SELECT
0
VCR/DVD
TRACKING/
SET
+
Country/Area
AUSTRALIA
BELGIUM
CANADA
Code
AU
BE
CA
CHINA CN
CHINA HONG KONG
DENMARK
FINLAND
FRANCE
GERMANY
HK
DK
FI
FR
DE
INDONESIA
ITALY
JAPAN
MALAYSIA
ID
IT
JP
MY
Country/Area
NETHERLANDS
NORWAY
PHILIPPINES
SINGAPORE
SPAIN
SWEDEN
SWITZERLAND
TAIWAN
THAILAND
UNITED KINGDOM
UNITED STATES
Code
NL
NO
PH
RUSSIAN FEDERATION RU
SG
ES
SE
CH
TW
TH
GB
US a) Press / to select the first character.
b) Press the / to shift and press / to select the second character.
c) Press ENTER.
SELECT/
ENTER
6
Press / to select the parental lock level, then press ENTER.
DVD MENU
ZOOM
CH
RETURN
TITLE REPEAT A-B
AB C
Operation
Pause/Still
Parental Lock
Title Stop
Auto
Off
Off
Off
On
Area Code
Level
U S
7
: Select : Enter
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC TV/VCR
REW/SEARCH
INDEX/SKIP
REC/OTR
PLAY
STOP
SEARCH/F.FWD
SKIP/INDEX
SLOW PAUSE/STILL
You cannot play DVD discs rated higher than the level you selected unless you cancel the parental lock function.
For example, when you select level 7, discs rated higher than level
7 are locked out and cannot be played.
The parental lock level is equivalent to following the USA movie ratings.
Level 7: NC-17
Level 6: R
Level 4: PG 13
Level 3: PG
Level 1: G
17 years old and above
Under 17 years old Parental guidance suggested
Parental guidance less than 13 years old
Parental guidance
All ages
The parental lock levels for other countries/areas other than the U.S.
are included for future use. Check the appropriate parental lock level when you buy a DVD disc equipped with the parental lock feature in the future.
7
To make the SETUP screen disappear, press SET UP.
To change the parental lock level
Follow steps 4- 6.
To change your 4-digit security code
1) After selecting “On” or “Off” press STOP four times, then press
ENTER.
The 4-digit security code is cleared.
2) Press Number Keys to create a new 4-digit security code.
3) Press ENTER.
46
2A77001AE(46-51) 46 8/29/02, 11:06 AM
You can select the language of the disc menu messages of DVDs.
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Setting menu language
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
Press SET UP in the stop mode.
Press or to select
“Language”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
2
Press or to select “Disc
Menu Language”.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
: Select : Enter
3
Press ENTER.
Press or to select your desired language, then press
ENTER.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
English
French
Spanish
Others
Code E S
: Select : Enter
English, French, Spanish
The selected language is the first-priority Menu language.
Others: Other languages can be selected (See the Table of languages on page 57).
4
To make the SETUP screen disappear, press SET UP.
2A77001AE(46-51) 47 8/29/02, 11:06 AM
47
Setting subtitle language
The same subtitle language can always be selected even if you replace the disc or turn the power off.
•
•
Preparation:
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
1
Press SET UP in the stop mode.
Press or to select
“Language”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
4 5 6 INPUT SELECT
: Select : Enter
7 8 0 9
CH
TRACKING/
SET
—
SELECT/
ENTER
TRACKING/
SET
+
2
Press or to select “Subtitle
Language”.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
: Select : Enter
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
3
Press ENTER.
Press or to select your desired language, then press
ENTER.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
: Select
English
French
Spanish
No Subtitle
Others
Code E S
: Enter
INDEX/SKIP STOP SKIP/INDEX
SLOW PAUSE/STILL
English, French, Spanish
The subtitle is displayed with the selected language if it is recorded on the disc.
Others: If you want to select another language, enter the language code (See the Table of languages on page 57).
REC/OTR
No Subtitle:
Subtitles do not appear.
4
To make the SETUP screen disappear, press SET UP.
NOTES:
• If the selected language is not recorded on the disc, the first-priority language is selected.
• Some DVD discs may be set to display
Subtitles in a different language than you selected. A prior subtitle language may be programmed on the disc.
48
2A77001AE(46-51) 48 8/29/02, 11:06 AM
The same audio soundtrack language can always be selected by your unit even if you replace the disc or turn the power off.
Setting audio soundtrack language
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
Press SET UP in the stop mode.
Press or to select
“Language”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
2
Press or to select “Audio
Language”.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
: Select : Enter
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
3 Press ENTER.
Press or to select your desired Audio Language, then press ENTER.
AB C
Language
On-Screen Language ENG
Disc Menu Language ENG
Audio Language ENG
Subtitle Language ENG
English
French
Spanish
Others
Code E S
: Select : Enter
English, French, Spanish
The language you have selected will play if it is recorded on the disc.
Others: If you want to select another language, enter the language code (See the Table of languages on page 57).
4
To make the SETUP screen disappear, press SET UP.
NOTES:
• If the selected language is not recorded on the disc, the original language will be heard.
• Some DVD discs may be played in a different language than you selected.
A prior language may be programmed on the disc.
49
2A77001AE(46-51) 49 8/29/02, 11:06 AM
Setting the aspect ratio of TV screen
You can select the aspect ratio for your TV.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
1
Press SET UP in the stop mode.
Press or to select
“Picture”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
INPUT SELECT 4 5 6
: Select : Enter
7 8 9 0
TRACKING/
SET
—
CH
TRACKING/
SET
+
2 Press ENTER.
Press or to select your desired screen type, then press
ENTER.
Picture
TV Shape 4:3LB
AB C
4:3 Letterbox
4:3 Normal
16:9 Widescreen
SELECT/
ENTER
: Select : Enter
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
PLAY
NOTES:
• The displayable picture size is preset on the DVD video disc. Therefore, the playback picture of some DVD video discs may not conform to the picture size you select.
• When you play DVD video discs recorded in the 4:3 picture size only, the playback picture always appears in the
4:3 picture size regardless of the TV shape setting.
• If you select “16:9 widescreen” and you own a 4:3 TV set, the DVD playback picture will be horizontally distorted during playback. Images will appear to be horizontally compressed. Always be sure that your TV shape conforms to the actual TV in use.
You have the following screen sizes to choose from:
4:3 Letterbox:
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars above and below the picture.
4:3 Normal:
Select when a standard 4:3 TV is connected.
Displays pictures cropped to fill your TV screen. Either or both sides of the picture are cut off.
16:9 Widescreen:
Select this mode when connecting to a wide-screen TV.
A wide screen picture is displayed full size.
3
To make the SETUP screen disappear, press SET UP.
50
2A77001AE(46-51) 50 8/29/02, 11:06 AM
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Setting on Screen display
•
•
Preparation:
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
1
Press SET UP in the stop mode.
Press or to select “Display”
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
2 Press or to select “On-
Screen Display”.
AB C
Display
On-Screen Display On
Background
Screen Saver
Picture
On
: Select : Enter
3
Press ENTER.
Press or to select “On” or
“Off”, then press ENTER.
AB C
Display
On-Screen Display Off
Background
Screen Saver
Picture
On
Off
On
: Select : Enter
On: Operational modes (e.g. “ ”, “ press the buttons (factory setting).
Off: Operational modes (e.g. “ ”, “ you press any buttons.
”) appear when you
”) do not appear when
4
To make the SETUP screen disappear, press SET UP.
2A77001AE(46-51) 51 8/29/02, 11:06 AM
51
Setting Audio
52
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3 DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED
TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
NOTES:
• The Dynamic Range Control function works only during playback of Dolby
Digital recorded discs.
• The level of Dynamic Range Control may differ depending on the DVD video disc.
• The vocal output feature is used during playback of Dolby Digital (multi-channel) recorded DVD KARAOKE discs. This feature allows you to turn off vocal audio tracks, or restore them for background accompaniment.
• When playing KARAOKE, connect the appropriate audio equipment such as an amplifier to the DVD player.
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Audio Out Select
Select the output sound format corresponding to your system connection.
For details of sound recording systems, see on page 55.
1
Press SET UP in the stop mode.
Press or to select “Audio”.
AB C
Audio
Audio Out Select Bitstream
Dynamic Range Control On
Karaoke Vocal On
Bitstream
Analog 2ch
PCM
2 Press or to select “Audio Out
Select”, then press ENTER. Press or
to select your desired output sound, then press ENTER.
: Select : Enter
Bitstream: Select when connected to an amplifier equipped with a Dolby
Digital, DTS, MPEG1 or MPEG2 decoder. The DVD/VCR outputs digital audio information in the bitstream format when you play a
DVD video disc recorded on the Dolby Digital, DTS, MPEG1 or
MPEG2 recording system.
Analog 2ch: Select when connected to a TV, Dolby Pro Logic or stereo system via the analog audio jacks.
PCM: Select when connected to a 2 channel digital stereo amplifier.
The DVD/VCR outputs sounds in the PCM 2ch format when you play a DVD video disc recorded on the Dolby Digital. MPEG1 or
MPEG2 recording system.
3
To make the SETUP screen disappear, press SET UP.
Dynamic Range Control
Turn on or off a function that makes faint sounds easier to hear even if you lower the volume during late hours playback.
1
Press SET UP in the stop mode.
Press or to select “Audio”.
2
Press or to select “Dynamic
Range Control”, then press ENTER.
Press or to select “On” or “Off”, then press ENTER.
Off: Full dynamic range is maintained.
On: Dynamic range is reduced.
3 To make the SETUP screen disappear, press SET UP.
AB C
Audio
Audio Out Select Bitstream
Dynamic Range Control On
Karaoke Vocal Off
Off
On
: Select : Enter
Karaoke Vocal
Turn on or off the vocal output during DVD KARAOKE disc playback.
1
Press SET UP in the stop mode.
Press or to select “Audio”.
2
Press or to select “Karaoke
Vocal”, then press ENTER.
Press or to select “On” or “Off”, then press ENTER.
Off: The primary vocal is not output.
On: The primary vocal is output when it is recorded on the disc.
3
To make the SETUP screen disappear, press SET UP.
AB C
Audio
Audio Out Select Bitstream
Dynamic Range Control On
Karaoke Vocal Off
Off
On
: Select : Enter
2A77001AE(52-57) 52 8/29/02, 11:05 AM
2A77001AE(52-57)
4
7
1
POWER EJECT
OPEN/
CLOSE VCR/DVD
2 3
DISPLAY/CALL
INPUT SELECT 5
8
6
9
CH
0
TRACKING/
SET
—
TRACKING/
SET
+
SELECT/
ENTER
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Setting Operation
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Pause/Still
Select the resolution of still pictures.
1
Press SET UP in the stop mode.
Press or to select
“Operation”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
2
Press or to select “Pause/
Still”, then press ENTER. Press
or to select “Auto” or
“Frame”, then press ENTER.
AB C
Operation
Pause/Still Auto
Parental Lock Off
Title Stop Off
Auto
Frame
: Select : Enter
Auto: For normal use. Still and fast motion images can be paused.
Frame: The resolution of still pictures is improved, so that you can make a motionless picture clearer when you pause it.
3
To make the SETUP screen disappear, press SET UP.
Title Stop
Turn on or off a feature that automatically stops playback after a title has been viewed.
1
Press SET UP in the stop mode.
Press or to select “Operation”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
2
Press ENTER, then press or
to select “Title Stop”, then press ENTER.
Press or to select “On” or
“Off”, then press ENTER.
Off: The DVD/VCR continues after playback of a title is completed.
On: The DVD/VCR stops after playback of a title is completed.
AB C
Operation
Pause/Still Auto
Parental Lock Off
Title Stop Off
Off
On
: Select : Enter
3 To make the SETUP screen disappear, press SET UP.
53
8/29/02, 11:05 AM 53
Setting Background/Setting Screen Saver
Preparation:
• Turn ON the TV and set to the video input mode.
• Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Setting Background
Select the background color or background picture.
POWER EJECT
OPEN/
CLOSE VCR/DVD
1 2 3 DISPLAY/CALL
4 5 6 INPUT SELECT
1
Press SET UP in the stop mode.
Press or to select “Display”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
7 8 9 0
TRACKING/
SET
—
CH
SELECT/
ENTER
TRACKING/
SET
+
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
AUDIO/
AUDIO SELECT
MEMORY/
ZERO RETURN
ANGLE/
COUNTER RESET
CLOCK/
COUNTER
TIMER REC
SUB TITLE/
ATR
PLAY MODE/
SPEED TV/VCR
: Select : Enter
2
Press or to select
“Background”, then press
ENTER. Press or to select your desired background, then press ENTER.
AB C
Display
On-Screen Display On
Background Picture
Screen Saver On
Blue
Gray
Picture
Jacket
Blue: Blue background.
Gray: Gray background.
: Select : Enter
Picture: Use the picture which appears when you turn on the
DVD/VCR as a background.
Jacket: Use the jacket picture included on some discs as a background. If it is not included, a gray background will be substituted.
3 To make the SETUP screen disappear, press SET UP.
REW/SEARCH PLAY SEARCH/F.FWD
INDEX/SKIP
REC/OTR
STOP SKIP/INDEX
SLOW PAUSE/STILL
Setting Screen Saver (DVD only)
To turn the screen saver on or off.
1
Press SET UP in the stop mode.
Press or to select
“Display”.
Picture
TV Shape 4:3LB
VIDEO OUT SELECT
AB C
: Select : Enter
2
Press or to select “Screen
Saver”, then press ENTER.
Press or to select “On” or
“Off”, then press ENTER.
AB C
Display
On-Screen Display On
Background Picture
Screen Saver On
Off
On
Off: The screen saver is disengaged.
On: The screen saver operates in 10 minutes after you press
PAUSE/STILL.
: Select : Enter
3 To make the SETUP screen disappear, press SET UP.
54
2A77001AE(52-57) 54 8/29/02, 11:05 AM
Setting initial setup/output sound conversion table
You can install the initial system setting.
1
POWER
2
EJECT
3
OPEN/
CLOSE VCR/DVD
DISPLAY/CALL
Preparation:
•
•
Turn ON the TV and set to the video input mode.
Press VCR/DVD to select the DVD mode. (The DVD indicator will light.)
Setting initial setup
1
Press SET UP in the stop mode.
Press or to select “Initial
Setup”.
Picture
TV Shape 4:3LB
AB C
4 5 6 INPUT SELECT
: Select : Enter
7 8 9 0
CH
TRACKING/
SET
—
SELECT/
ENTER
TRACKING/
SET
+
2
Press ENTER, then press or
to select “On-Screen
Language”, “TV Shape” or
“Audio Out Select”.
AB C
Initial Setup
On-Screen Language ENG
TV Shape
Audio Out Select
4:3LB
Bitstream
English
Fran ais
Espa ol
: Select : Enter
DVD MENU
SET UP/
VCR MENU
CH
CLEAR/
CANCEL RETURN
ZOOM TITLE REPEAT A-B
On-Screen Language:
TV Shape:
Audio Out Select:
See on page 36.
See on page 50.
See on page 52.
3 To make the SETUP screen disappear, press SET UP.
Output sound conversion table
(sampling frequency/quantization bit)
You can select the output sound format corresponding to your system connection (see page 52).
Discs
DVD video discs
Audio CDs
Recording system
Dolby Digital
Linear PCM
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
DTS
MPEG1, MPEG2
Linear PCM 44.1 kHz/16 bit
DTS
ÒBitstreamÓ ÒAnalog 2chÓ ÒPCMÓ
DIGITAL AUDIO
OUT jack
ANALOG AUDIO
OUT jack
DIGITAL AUDIO
OUT jack
ANALOG AUDIO
OUT jack
Bitstream
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Bitstream
Bitstream
44.1 kHz/16 bit
Bitstream
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
Ð
48 kHz/16 bit
44.1 kHz/16 bit
(Noise)
Bitstream 48 kHz/20 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/16 bit
Ð
Ð
Ð
Bitstream
48 kHz/24 bit
96 kHz/16 bit
96 kHz/20 bit
96 kHz/24 bit
Ð
Bitstream 48 kHz/16 bit
44.1 kHz/16 bit 44.1 kHz/16 bit
Bitstream (Noise)
DIGITAL AUDIO
OUT jack
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
48 kHz/16 bit
Ð
48 kHz/16 bit
44.1 kHz/16 bit
Bitstream
ANALOG AUDIO
OUT jack
48 kHz/20 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
48 kHz/16 bit
48 kHz/20 bit
48 kHz/24 bit
Ð
48 kHz/16 bit
44.1 kHz/16 bit
(Noise)
55
2A77001AE(52-57) 55 8/29/02, 11:06 AM
Status display of Disc
You can view information on the operation status and access the settings.
1
With each press of DISPLAY, the status of the disc will appear on the screen and change as follows.
Symbol mark of the feature you selected is displayed.
DVD CD
T 2 C 3 -0:21:28
EAM T 2 C 3 0:08:16 T 1 00:30 T 1 -03:38 EAM EPM
EAM
2CH
IOOM
X
1
C
EAM
2CH
IOOM
X
1
C
EAM
PCM
EAM
PCM
OFF OFF
T 2 C 3 0:08:16 BIT
RATE
9.2Mbps
EAM
2CH
IOOM
X
1
C
T 2 C 3
EAM
2CH
IOOM
X
1
C
T 1 01:14
----- CD TEXT -----
Disc Title:
No Text
Track Title:
No Text
EAM
PCM
T 1
EAM
PCM
2 Press or to select the desired symbol mark, then press ENTER.
T : Title number (Track number)
Press / or Number keys to locate a title or track, then press PLAY.
C : Chapter number
Press / or Number keys to locate a Chapter, then press PLAY.
Audio setting
See page 43.
: Elapsed (remaining) time of the current title
Press Number keys to locate a desired Location, then press PLAY.
: Subtitle setting
See page 43.
ZOOM : To zoom a picture
See page 39.
: To stop playback
See page 37.
: Fast reverse playback
See Page 38.
: Angle setting
See page 44.
: Audio Out Select setting
BST: Bitstream 2CH:Analog 2ch PCM:PCM
See page 52.
: Playback starts from the beginning of the current chapter or track.
See page 38.
: To start playback
See page 37.
: Fast forward playback
See page 38.
: To locate succeeding chapters or tracks.
See page 38.
: To begin slow motion playback
See page 38.
: To turn off the display
CD TEXT
Displays CD text data if included on the audio
CDs. (Some letters may not be displayed properly depending on the disc.)
: To pause playback
See page 38.
Data transfer rate (Mbit/s)
Amount of picture, sound and subtitle data in the DVD video disc transferred per second.
The larger the value is, the more data processed, but this does not necessarily insure better picture quality.
56
2A77001AE(52-57) 56 8/29/02, 11:06 AM
Table of languages
Enter the appropriate code for the initial settings "Audio", "Subtitle" and/or "Menu" (see pages 47-49).
Abbreviation
– – –
Language
No alternate language
Chinese
Dutch
English
French
German ltalian
Japanese
Korean
Malay
Spanish
Afar
Abkhazian
Afrikaans
Amharic
Arabic
Assamese
Aymara
Azerbaijani
Bashkir
Belorussian
Bulgarian
Bihari
Bislama
Bengali, Bangla
Tibetan
Breton
Catalan
Corsican
Czech
Welsh
Danish
Bhutani
Greek
Esperanto
Estonian
Basque
Persian
Finnish
Fiji
Faroese
Frisian
Irish
Scottish Gaelic
Galician
BO
BR
CA
CO
CS
CY
DA
DZ
BG
BH
BI
BN
AY
AZ
BA
BE
CHI (ZH)
DUT (NL)
ENG (EN)
FRE (FR)
GER (DE)
ITA (IT)
JPN (JA)
KOR (KO)
MAY (MS)
SPA (ES)
AA
AB
AF
AM
AR
AS
EL
EO
ET
EU
FA
FI
FJ
FO
FY
GA
GD
GL
Abbreviation Language
Guarani
Gujarati
Hausa
Hindi
Croatian
Hungarian
Armenian
Interlingua
Interlingue
Inupiak
Indonesian
Icelandic
Hebrew
Yiddish
Javanese
Georgian
Kazakh
Greenlandic
Cambodian
Kannada
Kashmiri
Kurdish
Kirghiz
Latin
Lingala
Laotian
Lithuanian
Latvian, Lettish
Malagasy
Maori
Macedonian
Malayalam
Mongolian
Moldavian
Marathi
Maltese
Burmese
Nauru
Nepali
Norwegian
Occitan
(Afan) Oromo
Oriya
Panjabi
Polish
Pashto, Pushto
LN
LO
LT
LV
MG
MI
MK
ML
KK
KL
KM
KN
KS
KU
KY
LA
IW
JI
JW
KA
IE
IK
IN
IS
GN
GU
HA
HI
HR
HU
HY
IA
OC
OM
OR
PA
PL
PS
MN
MO
MR
MT
MY
NA
NE
NO
Abbreviation Language
Somali
Albanian
Serbian
Siswati
Sesotho
Sundanese
Swedish
Swahili
Tamil
Telugu
Tajik
Thai
Tigrinya
Turkmen
Tagalog
Setswana
Portuguese
Quechua
Rhaeto-Romance
Kirundi
Rumanian
Russian
Kinyarwanda
Sanskrit
Sindhi
Sango
Serbo-Croatian
Singhalese
Slovak
Slovenian
Samoan
Shona
Tongan
Turkish
Tsonga
Tatar
Twi
Ukrainian
Urdu
Uzbek
Vietnamese
Volapük
Wolof
Xhosa
Yoruba
Zulu
TA
TE
TG
TH
TI
TK
TL
TN
SO
SQ
SR
SS
ST
SU
SV
SW
SD
SG
SH
SI
SK
SL
SM
SN
PT
QU
RM
RN
RO
RU
RW
SA
VI
VO
WO
XH
YO
ZU
TO
TR
TS
TT
TW
UK
UR
UZ
57
2A77001AE(52-57) 57 8/29/02, 11:06 AM
Problems and troubleshooting
Use the following check list for troubleshooting when you have problems with your unit. Consult your local dealer or service outlet if problems persist.
Be sure all connections are properly made when using with other units.
DVD/VCR
SYMPTOMS POSSIBLE SOLUTIONS PAGE
DVD/VCR does not operate.
No picture.
No sound.
The remote control does not function.
No CATV reception
• Make sure the power cord is plugged in.
• Try another AC outlet.
• Power is off, check fuse or circuit breaker.
• Unplug unit, then plug it back in.
• Select the DVD or VCR mode before operating.
5
–
–
5
18,36
• Antenna connection is not correct or antenna cable is disconnected.
• The video channel is not in the correct position or the TV is not set to the video channel 3 or 4.
• Check the unit is connected correctly.
• The video input selector of the TV is not set to VIDEO. Set to
VIDEO (or equivalent).
• Channel is set to the external mode.
• Check the unit is connected correctly.
• Check the input selector of the amplifier is set properly.
• The unit is in the Special playback mode.
12~15
18
12~17
–
–
12~17
–
26,38
• Aim at the remote control at the remote sensor.
• Operate within Approx. 5 Meters or reduce the light in the room.
• Clear the path of the beam.
• The batteries are weak. Replace the batteries.
• Check the batteries are inserted correctly.
• Check the frequency code is set correctly.
• Check all CATV connections.
• Station or CATV system problems, try another station.
11
14,15
VCR
TV recording does not work.
Timer recording does not work.
Noise bars on screen.
• The erase prevention tab of the video cassette is broken off.
• The unit is in the external input mode.
• The time is not set correctly.
• The recording start/end time is not set correctly.
• The TIMER has not been pressed ( is not lit).
• Tracking adjustment beyond range of automatic tracking circuit.
Try Manual tracking adjustment.
• Video heads are dirty.
• The tape is worn or damaged.
24,28
19
31
31
26
59
–
DVD
Display is not shown in your language.
• Select proper language in the menu options.
Playback doesn’t start.
Stopping playback, slow-motion play, repeat play, or memory play, etc. cannot be performed.
• No disc is inserted.
• The disc may be dirty. Clean up the disc.
• The unit cannot play DVD-ROMs, etc.
• Some discs may not do some of the functions.
• When you press VCR MENU while watching a DVD with the connections of the DVD exclusive terminal (S-VIDEO cable or
COMPONENT cable) to a TV, you cannot perform all the DVD functions. In this case, wait for approx. 60 seconds with no pressing of any buttons.
36
37
35
35
–
–
58
2A77001AE(58-BACK) 58 8/29/02, 11:05 AM
Problems and troubleshooting / Video head cleaning
SYMPTOMS
No 4:3 (16:9) picture
No on-screen display
No surround sound
The unit or remote operation key is not functioning.
Playback does not start when the title is selected.
Audio soundtrack and/or subtitle language is not changed when you play back a DVD.
POSSIBLE SOLUTIONS
• The setup does not match your TV.
• Select Display On.
• The setup does not match your stereo system.
• Turn off the unit and unplug the AC power cord for several minutes, then replug it.
• Check the Parental setup.
• Multilingual language is not recorded on the DVD disc.
No subtitle
Angle cannot be changed.
appears on the screen.
• Some discs have no subtitles.
• Subtitles are cleared. Press SUB TITLE.
• Multi-angles are not recorded on the DVD disc.
• The function is prohibited with the unit or the disc.
48
44
–
PAGE
50
51
17
–
45
48,49
Video head cleaning
Video head clogging
The video heads are the means by which the DVD/VCR reads the picture from the tape during playback. In the unlikely event that the heads become dirty enough to be clogged, no picture will be played back. This can easily be determined if, during playback of a known good tape, there is good sound, but no picture (picture is extremely snowy). If this is the case, have the DVD/VCR checked by qualified service personnel.
Good Picture Snowy Picture
NOTES: • DO NOT ATTEMPT TO CLEAN THE VIDEO HEADS OR SERVICE THE UNIT BY REMOVING THE
REAR COVER.
• Video heads may eventually wear out and should be replaced when they fail to produce clear pictures.
• To help prevent video head clogging, use only good quality VHS tapes. Discard worn out tapes.
FOR ADDITIONAL SET-UP OR OPERATING ASSISTANCE, PLEASE VISIT OUR WEBSITE AT
WWW.MEMCORPINC.COM OR CONTACT CUSTOMER SERVICE AT 1-800-919-3647
PLEASE KEEP ALL PACKAGING MATERIAL FOR AT LEAST 90 DAYS IN CASE YOU NEED TO RETURN THIS
PRODUCT TO YOUR PLACE OF PURCHASE OR MEMOREX.
FOR PARTS AND ACCESSORIES, CONTACT FOX INT'L AT 1-800-321-6993.
59
2A77001AE(58-BACK) 59 8/29/02, 11:05 AM
Specifications
GENERAL
Power supply:
Power consumption:
Weight:
Dimensions:
AC 120V 60Hz
Operation: 20W
Stand by: 3W
9.9lbs (4.5 kg)
Width : 16-15/16 inches (430 mm)
Height : 3-7/8 inches (99 mm)
Depth : 12-3/8 inches (314.5 mm)
Inputs/Outputs:
Video:
Audio:
Antenna:
Hi-Fi Frequency Response:
Hi-Fi Dynamic Range:
In: 1Vp-p/75 ohm
Out: 1Vp-p/75 ohm
In: –8dBm/50K ohm
Out: –8dBm/1K ohm
UHF/VHF IN/OUT: 75 ohm coaxial
20Hz to 20,000Hz
More than 90dB
VCR section
Video Head:
Audio Track:
Tuner:
RF Channel Output:
F.FWD/REW Time at 25˚C (77˚F):
4 Rotary Heads
Hi-Fi Sound - 2 Tracks / MONO Sound - 1 Track
181 Channel Freq. Synthesized
VHF 2-13
UHF 14-69
CATV 14-36 (A)-(W)
37-59 (AA)-(WW)
60-85 (AAA)-(ZZZ)
86-94 (86)-(94)
95-99 (A-5)-(A-1)
100-125 (100)-(125)
01 (5A)
Channel 3 or 4, Switchable
Approx. 1minute and 48 seconds (with T-120 Cassette Tape)
DVD section
Signal system:
Applicable disc:
Audio characteristics:
Frequency response:
S/N Ratio:
Harmonic distortion:
Wow and flutter:
Dynamic range:
Output:
Pickup:
ACCESSORIES:
NTSC
DVD (12cm, 8cm), CD (12cm, 8cm)
DVD: 4Hz - 22KHz
CD: 4Hz - 20KHz
90dB
0.01%
Below Measurable Level
90dB
Video : (RCA) 1 Vp-p/75ohm
Audio : (RCA) –8 dBm/1Kohm
Digital Audio : 0.5Vp-p/75 ohm
CD : Wavelength: 775 - 805 nm
Maximum output power: 0.5 mW
DVD : Wavelength: 640 - 660 nm
Maximum output power: 1.0 mW
Remote control x 1
75 ohm Coaxial Cable x 1
AUDIO/VIDEO Cable x 1
60
2A77001AE(58-BACK) 60 8/29/02, 11:05 AM
Memo
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
61
2A77001AE(58-BACK) 61 8/29/02, 11:05 AM
advertisement
* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project
Related manuals
advertisement
Table of contents
- 3 IMPORTANT SAFEGUARDS
- 5 Power Source
- 6 Features
- 7 Contents
- 8 Parts and functions
- 9 Display
- 10 Remote control
- 12 Basic connections
- 14 CATV (CABLE TV) connections
- 16 Playback connection
- 18 Setting the video channel
- 18 Setting the language
- 19 Auto clock setting
- 21 Manual clock setting
- 22 Tuner setting
- 23 To ADD/DELETE channels
- 23 Noise elimination
- 24 Loading and Unloading a cassette tape
- 25 Cassette tape playback
- 26 Special playback
- 27 ZERO RETURN function
- 27 Video index search system
- 28 Recording a TV program
- 30 One-touch Timer Recording (OTR)
- 31 Timer recording
- 33 Stereo recording and playback
- 33 Separate Audio Program (SAP)
- 34 Duplicating a video tape
- 36 Setting setup language
- 37 Playback procedure
- 38 Special playback
- 39 Zooming
- 40 Repeat playback
- 41 Memory playback/Random playback
- 42 MP3 playback
- 43 Changing soundtrack language
- 43 Changing subtitles language
- 44 Changing angles
- 44 Title selection
- 44 DVD menu
- 45 Parental control
- 47 Setting menu language
- 48 Setting subtitle language
- 49 Setting audio soundtrack language
- 50 Setting the aspect ratio of TV screen
- 51 Setting on screen display
- 52 Setting Audio
- 53 Setting Operation
- 54 Setting Background
- 54 Setting Screen Saver (DVD only)
- 55 Setting initial setup
- 55 Output sound conversion table
- 56 Status display of disc
- 57 Table of languages
- 58 Problems and troubleshooting
- 59 Video head cleaning
- 60 Specifications