16 3 en~v~Specification Sheet

16 3 en~v~Specification Sheet
HEAT RECOVERY VENTILATOR
CONSTRUCTO 1.0 HRV
Part no. 41502 (TOP PORTS)
Part no. 41500 (SIDE PORTS)
39 to 98 CFM (0.4 in. w.g.)
Controls
• This unit is very simple to operate. Once it is installed, press on its
push button, located on on the bottom of the unit, to activate it.
Press once for low speed, once again for high speed, and once more
to stop it.
• For more convenience, this unit can also be controlled by an optional
main control. For a complete list of optional main and auxiliary
controls available, refer to the Wall Control Compatibility Chart
on last pages of wall controls specification sheet, available at
www.venmar.ca.
• For more details about controls, refer to the Main and auxiliary wall
controls user guide, also available at www.venmar.ca.
Options
VB0069
AN INGENIOUS AIR EXCHANGE SOLUTION THAT’S
AS VERSATILE AS IT IS COMPACT!
Configured with factory built vertical or horizontal ports, the
AVS Constructo 1.0 HRV is the most versatile 98-cfm unit available on
the market today. Among its exclusive features, this unit is equipped
with integrated balancing and backdraft dampers in its exhaust to
outside and fresh air supply ports.
Its operation can be interlocked with an existing furnace without
adding an extra relay. Also, for more convenience, its latches can be
relocated on its front (as shown on unit picture). This compact,
lightweight, and powerful unit is the ideal choice for small single-family
homes, high rise residential building and other limited space applications.
What’s more, it is the only air exchanger of its size that can be upgraded
from an HRV to an ERV, simply by changing its core.
• Versatile horizontal or vertical port configuration
• Removable terminal block to ease auxiliary wall control connections
• Integrated pressure taps, if balancing required by building code
• Twin high-pressure blowers
• ENERGY STAR® qualified
REPAIRS AND MAINTENANCE
All parts of the AVS Constructo 1.0 HRV that could need maintenance
can be removed in less than 5 minutes, allowing direct access for
easy repairs. The PSC motors are permanently lubricated. Finally, the
removable electrical drawer with pull-out PCB assembly allows easy
access for maintenance of major sub-components.
WARRANTY
The AVS Constructo 1.0 HRV is protected by a 2-year warranty on parts
only. The heat recovery core is covered by a limited lifetime warranty,
with the original proof of purchase.
Available at:
• Complete line of registers and diffusers
• Electric duct heater
• Dual exterior hood kit (including the Tandem® transition),
part no. 14690
Homeshield™ Defrosting System
The AVS Constructo 1.0 HRV uses a unique defrosting method. No
negative pressure is created by air exhausted to the outside, as the air
is recirculated into the house, helping to prevent any backdraft.
OUTSIDE
TEMPERATURE
STALE AIR
FROM
BUILDING
FILTERED
AIR TO
BUILDING
VF0036
DEFROST CYCLE
(IN MINUTES)
oC
oF
DEFROST/
OPERATION
WARMER
THAN -5
WARMER
THAN 23
NO DEFROST
-5 TO -27
23 TO -17
8/25
-27 & LESS
-17 & LESS
10/22
Heat Recovery Core
Dimensions: 13” x 19” x 6 7/8” (33 cm x 48.3 cm x 17.3 cm)
Exchange surface: 55 ft.2 (5.1 m2)
Weight: 3.75 lb. (1.7 kg)
Material: Polypropylene
Type: Cross flow
Warranty: Limited lifetime
Requirements and standards
• Complies with the UL 1812 requirements regulating the installation
of Heat Recovery Ventilators
• Complies with the CSA C22.2 no. 113 Standard applicable to ventilators
• Complies with CSA C444 requirements regulating the installation of
Heat Recovery Ventilators
• Technical data was obtained from published results of tests relating
to CSA C439 Standards
• HVI certified and ENERGY STAR® qualified
DIMENSIONS: AVS CONSTRUCTO 1.0 HRV (PORTS ON SIDES)
27 1/16” (688 mm)
ALL PORTS FITS
5” DIAMETER DUCTS
4” (102 mm)
1
2
6”
(152 mm)
NET SUPPLY
AIR FLOW
L/S
53
51
48
46
43
41
39
37
34
34
CFM
M3/H
111
107
101
98
91
88
82
79
73
71
191
184
172
167
155
148
139
134
124
121
L/S
53
51
48
47
43
42
39
38
35
34
4
3: FRESH AIR FROM OUTDOORS PORT
4: EXHAUST AIR TO OUTDOORS PORT
2” (51 mm)
VENTILATION PERFORMANCE
12 3 /16”
(310 mm)
3
13¾”
(349 mm)
1: FRESH AIR TO BUILDING PORT
2: EXHAUST AIR FROM BUILDING PORT
VK0055A
EXTERNAL
STATIC PRESSURE
PA
IN. W.G.
25
0.1
50
0.2
75
0.3
100
0.4
125
0.5
150
0.6
175
0.7
200
0.8
225
0.9
250
1.0
19 13 /16” (503 mm)
22 9/16” (574 mm)
AVS CONSTRUCTO 1.0 HRV (PORTS ON TOP)
ALL PORTS FITS
5” DIAMETER DUCTS
GROSS AIR FLOW
SUPPLY
EXHAUST
CFM
M3/H
L/S
CFM
M3/H
112 190 57 120 204
108 184 54 114 194
102 173 52 110 187
99
168 49 105 178
92
156 47 100 170
88
151 45
96
163
83
141 43
91
155
80
136 40
85
144
74
126 37
79
134
72
122 36
76
129
1
4
4’’ (102 mm)
19 13 16”
(503 mm)
2
3
6’’ (152 mm)
22 9 16” (574 mm)
23¾” (603 mm)
2½”
(64 mm)
ENERGY PERFORMANCE
SUPPLY
TEMPERATURE
°C °F
HEATING
0 32
0 32
0 32
-25 -13
-25 -13
COOLING
35 95
NET AIR FLOW
L/S
CFM
23
30
39
23
30
50 85
64 109
83 141
48 82
64 109
-
-
M3/H
-
POWER
SENSIBLE
APPARENT LATENT RECOVERY/
CONSUMED RECOVERY
SENSIBLE
MOISTURE
EFFICIENCY EFFECTIVENESS
TRANSFER
WATTS
43
58
70
56
64
65
62
59
60
55
74
70
66
78
72
0.01
0.01
0.01
0.01
0
VK0056A
TOTAL RECOVERY EFFICIENCY
NOT TESTED
-
16¼”
(413 mm)
12 3 16”
(310 mm)
1: FRESH AIR TO BUILDING PORT
2: EXHAUST AIR FROM BUILDING PORT
3: FRESH AIR FROM OUTDOORS PORT
4: EXHAUST AIR TO OUTDOORS PORT
NOTE: All specifications are subject to change without notice.
SPECIFICATIONS
• Model: AVS Constructo 1.0 HRV
• Part number top ports: 41502
10.5” x 6.75” x 0.5” (26.7 cm x 17.2 cm x 1.3 cm)
• Part number side ports: 41500
• Housing: Pre-painted steel
• Total assembled weight (including
polypropylene core): 42 lb. (19 kg)
• Oval shaped ports; fit 5” diameter ducts
• Drain: 1/2” (1.2 cm) fittings with
10 ft. (3 m) PVC drain hose
Project:
Location:
Part no.:
Qty.:
Submitted by:
• Core filters: 30 ppi washable foam
• Insulation: Expanded polystyrene
• Mounting:
• Speed control on unit: Low & high speeds.
Other modes available with main and
optional wall controls
• Heat recovery core:
Suspension by chains
- Heat exchange surface area: 55 ft.2 (5.1 m2)
and springs
- Type/Material: Crossflow/Polypropylene
• Supply and exhaust blower motor: 2 motors • Unit electrical characteristics:
- Protection type: Thermally protected
Volts
Frequency
Ampere
Watts
- Insulation class: B
120
60 Hz
1
120
REMARKS
Date:
Residential Products Group, 550 Lemire Blvd., Drummondville, Qc, Canada J2C 7W9 - Tel.: 1-800-567-3855 Fax: 1-800-567-1715
www.venmar.ca
15/02 PRODUCT SHEET NO. 91047
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement