American Standard 7430151.002 Berwick® Single Handle Monoblock Bathroom Sink Faucet in Polished Chrome Installation instructions

BERWICK

™

VESSEL LAVATORY FITTING

Installation

Instructions

7430.15X

Thank you for selecting American-Standard...the benchmark of fine quality for over 100 years.

To ensure that your installation proceeds smoothly--please read these instructions carefully before you begin.

Certified to comply with ANSI A112.18.1M

M 9 6 8 6 4 2

Recommended Tools

Regular Screwdriver

Adjustable Wrench

Plumbers' Putty or Caulking Channel Locks

Phillips Screwdriver

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

1

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

INSTALL LAVATORY FAUCET

CAUTION

Turn off hot and cold water supplies before beginning.

Seat SEAL (1) into under side of ESCUTCHEON RING (2).

Seat ESCUTCHEON RING (2) with collar facing up into groove in faucet base.

Feed FAUCET SUPPLIES (3) and MOUNTING SHANK (4) through

ESCUTCHEON RING (2) and hole in mounting surface.

From below, install SUPPORT PLATE (7) GASKET (5) and MOUNTING

NUT (6) onto SHANK (4). Secure Faucet with MOUNTING NUT (6).

Before final tightening, adjust Faucet so that it is centered. Tighten

MOUNTING NUT (7) to complete mounting.

Note: For thick deck installations, the SUPPORT PLATE (7) can be omitted.

GROOVE

(FAUCET BASE)

COLLAR

2

1

4

MOUNTING SURFACE

7

5

6

3

2

MAKE WATER SUPPLY CONNECTIONS

Turn off hot and cold water supplies before beginning.

Connect FLEXIBLE SUPPLIES (1, 2) directly to wall supplies. Connection on fitting supplies are 3/8" compression. Connect left supply to Hot and right supply to the Cold wall supply. Use adjustable wrench to tighten connections. Do not over tighten.

Faucet supplies are 28" long from faucet base.

Note: If additional supply length is required, installer must purchase additional parts separately.

Important: If SUPPLY HOSES (1, 2) are too long, loop as illustrated to avoid kinking.

Figure A.

HOT

Figure A.

COLD

3

DRAIN INSTALLATION

Apply a bead of PUTTY to underside of

DRAIN BODY FLANGE (1).

Feed DRAIN BODY (1) down through lavatory.

Assembly GASKET (2) WASHER (3) and LOCKNUT (4) onto DRAIN BODY (1). Tighten LOCKNUT (4) firmly.

Assembly TAILPIECE (5) to DRAIN BODY (1).

28"

HOT

2

LOOP SUPPLIES

IF REQUIRED

COLD

1

PUTTY

1

2

3

4

5

M 9 6 8 6 4 2

4 TEST INSTALLED FAUCET

AND CHECK FOR LEAKS

With HANDLE (1) in OFF position, turn on WATER

SUPPLIES (2) and check all connections for leaks.

Remove AERATOR (3).

Operate HANDLE (1) to flush water lines thoroughly.

Replace AERATOR (3).

1

HOT

OFF

COLD

3

ON

HOT

COLD

2

5

SERVICE CAUTION

To remove or replace cartidge

Turn off hot and cold water supplies before beginning.

Turn valve to OFF position.

Pull out PLUG BUTTON (1) and remove HANDLE SCREW (2).

Pull off HANDLE (3) and CAP (4).

Unthread CARTRIDGE NUT (5) and remove.

Pull out CARTEIDGE (6).

Inspect CARTRIDGE (6) and O-RINGS (7) for debris and clean if necessary.

Clean MANIFOLD (8) and rinse clean.

Reinstall CARTRIDGE (6) and O-RINGS (7) onto MANIFLOD (8).

Reinstall CARTRIDGE NUT (5), CAP (4) and HANDLE ASSEMBLY (3).

If spout drips, operate handle several times from OFF to ON and HOT to

COLD position. Do not force - handles turn only 90˚.

1

REMOVE

2

2.5mm HEX KEY

INSTALL

4

5

3

6

7

8

6

CARE INSTRUCTIONS:

DO: SIMPLY RINSE THE PRODUCT CLEAN WITH CLEAR WATER. DRY WITH A SOFT COTTON FLANNEL CLOTH.

DO NOT: DO NOT CLEAN THE PRODUCT WITH SOAPS, ACID, POLISH, ABRASIVES, HARSH CLEANERS, OR A

CLOTH WITH A COARSE SURFACE.

M 9 6 8 6 4 2