Click here to IC600BF805 PDF for more information.

Click here to IC600BF805 PDF for more information.
SERIES SIX
PROGRAMMABLE
GEK-83513C
CONTROLLERS
8 inputs per module
AC/DC INPUT MODULES
GENERAL DESCRIPTION
An input circuit contains a rectifier, a noise filter to
reduce common mode transients, an opto-isolator, and a
Schmitt trigger (one-shot), which fires to indicate that a
voltage (AC or DC) in a specified range has been
detected. An active input circuit is indicated by a LightEmitting Diode (LED), visible through a lens on the
faceplate.
The AC/DC Input modules detect bipolar AC and DC
voltages supplied by, and controlled by, the user. The
modules are available in four versions: 12 Vac/dc, 24-48
Vac/dc, 115 Vac/dc, and 230 Vac/dc. The features and
benefits of these modules are summarized in Table 1.
A module contains eight inputs, divided into two groups,
each group sharing a neutral circuit (either N1 or N2).
Refer to Figure 1 (next page) for AC/DC Input module
specifications.
TABLE 1.
I
FEATURES
FEATURES AND BENEFITS
LED for each input/Color-coded faceplates.
I
Useful in a variety of applications.
Four modules available:
12 Vac/dc
24-48 Vac/dc
115 Vac/dc
230 Vac/dc
| ~~ ~ ~
BENEFITS
I
I
Allows visual inspection of l/O operations,
Eight inputs per module.
Efficient use of I/O rack spare.
Optically-coupled inputs.
Provides electrical isolation between user power supplies and Series Six Programmable Controller.
APPLICATIONS
* Monitor:
* Limit Switches
* Cam Switches
* Toggle Switches
* Relays
I
GEK-83513
AC/DC Input Modules
INSTALLATION
The AC/DC Input modules can be installed in an I/O rack
or the I/O rack section of the Model 60 Central Processor
Unit (CPU). Follow these steps:
Set the Dual-In-Line-Package (DIP) switches
directly behind the card slot on the rack backplane
to establish the correct correspondence between
the input terminals on this module and a group of
eight consecutive input numbers in the user
program. For further information on I/O DIPswitch settings, refer to the Installation Section of
the Series -Six Installation and Maintenance
Manual (GEK-25361).
Voltages from user field devices may
be present on the faceplate terminals,
even if the power supply in the I/O
rack is off. Care should be taken when
handling the faceplate of this module
or any wires connected to it.
,,
,
INPUT
Use to the extraction/insertion tool furnished with
the Series Six CPU to insert (or remove) this
module in the card slot.
Guide the faceplate over the circuit board so that
the terminals near the bottom of each are mated;
secure the faceplate to the rack using the thumbscrews at the top and bottom.
Refer to Figure 3. Connect one side of the user circuit to the appropriate input terminal (1 through
8). Circuits connected to inputs I through 4 must
have their opposite sides connected to either of the
Nl terminals. Likewise, circuits connected to
inputs 5 through 8 must have their opposite sides
connected to either of the N2 terminals.
In reference to Figure 3, note that wires connected
to the Nl terminals are at the same potential, as
are wires connected to the N2 terminals.
Each input terminal can accommodate one No. 12
AWG wire or two No. 14 AWG wires.
Guide the terminal cover onto the top of the terminal block, then slide it downward over the
terminals.
markable area is provided on the plastic lens beside
each LED for noting the function or source of each input.
The faceplates are color coded:
Green:
Orange:
White:
12V or 24-48V
115v
230V
Ref. PC-S&84-01 16
FIGURE 3. TYPICAL USER
INPUT CONNECTIONS
AC/DC Input Modules
GEK-83513
ORDERING INFORMATION
Module
Circuit Board and Faceplate
Circuit Board
Faceplate
12 Vac/dc
IC600BF806B
IC600YB806B
IC600FP806A
24-48 Vac/dc
IC600BF802B
IC600YB802B
IC600FP802A
115 Vac/dc
IC600BF804B
IC600YB804B
IC600FP804A
230 Vac/dc
IC600BF805B
IC600YB805B
IC600FP805A
CATALOG NUMBER REVISION SUFFIX
The equipment listed above having the catalog numbers shown and the same equipment
having a higher alpha suffix is designed for listing by UL for use as auxiliary control devices.
The equipment is a direct replacement for equipment having the same catalog number but a
lower alpha suffix.
The UL symbol on the nameplate means the product is
listed by Underwriters Laboratories Inc. (UL Standard No. 508, Industrial Control Equipment, subsection Electronic
Power Conversion Equipment. >
For
further information, contact your local GE Fanuc sales office.
G E FANUC AUTOMATION NORTH A M E R I C A , I N C . , CHARLOTTESVILLE,
4
JANUARY, 1984
VIRGlNlA
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement