American DJ X-move LED plus Instruction manual

Add to my manuals
12 Pages

advertisement

American DJ X-move LED plus Instruction manual | Manualzz

5/12

User Instructions

X-Move LED 25R General Information

Unpacking: Thank you for purchasing the X-Move LED 25R by American DJ

®

. Every X-Move LED 25R has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton appears to be damaged, carefully inspect your fixture for any damage and be sure all equipment necessary to operate the unit has arrived intact. In the event damage has been found or parts are missing, please contact our toll free customer support number for further instructions. Please do not return this unit to your dealer without contacting customer support first.

Introduction: The X-Move LED 25R is a nine channel DMX intelligent, moving head, mini LED fixture. The X-Move LED 25R can operate as a stand alone fixture or in a Master/Slave configuration. The X-Move LED

25R has three operating modes; a sound active, show mode, DMX controlled. For best results use fog or special effects smoke to enhance the beams projections.

Customer Support: American DJ

®

provides a toll free customer support line, to provide help and to answer any question should you encounter problems during your set up or initial operation. You may also visit us on the web at www.americandj.com for any comments or suggestions. Service Hours are Monday through Friday 8:00 a.m. to

4:30 p.m. Pacific Standard Time.

Voice:

Fax:

(800) 322-6337

(323) 582-2941

E-mail: [email protected]

To purchase parts online visit http://parts.americandj.com

Warning! To prevent or reduce the risk of electrical shock or fire, do not expose this unit to rain or moisture.

Warning! This may cause severe eye damage. Avoid looking directly into the light source at all times!

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 2

X-Move LED 25R General Instructions

To optimize the performance of this product, please read these operating instructions carefully to familiarize yourself with the basic operations of this unit. These instructions contain important safety information regarding the use and maintenance of this unit. Please keep this manual with the unit, for future reference.

X-Move LED 25R Features

• DMX-512 Protocol Compatible (Nine DMX Channels)

• 8 Colors + White

• 6 Rotating, Replaceable Gobos + Spot

• 3 Operating Modes - Sound Active, Show Mode, & DMX Control

• Internal Microphone

• Digital Display for Address and Function Setting

• UC3 Controller (Not Included)

• 4 Preprogrammed Shows

X-Move LED 25R Warranty Registration

The X-Move LED 25R carries a 3 year (1095 days) limited warranty.

Please fill out the enclosed warranty card to validate your purchase and warranty. You may also register your product online at www. americandj.com. All returned service items whether under warranty or not, must be freight pre-paid and accompany a return authorization

(R.A.) number. If the unit is under warranty you must provide a copy of your proof of purchase invoice. Please contact American DJ® customer support for a R.A. number.

X-Move LED 25R Handling Precautions

Caution!

There are no user serviceable parts inside this unit. Do not attempt any repairs yourself, doing so will void your manufactures warranty. In the unlikely event your unit may require service please contact

American DJ

®

.

During operation the housing may become extremely hot. Avoid touching the unit with bare hands while in use.

American DJ

®

will not accept any liability for any resulting damages caused by the non-observance of this manual or any unauthorized modification to this unit.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 3

X-Move LED 25R Safety Precautions

For Your Own Personal Safety, Please Read and Understand This

Manual Completely Before You Attempt To Install Or Operate

This Unit!

• To reduce the risk of electrical shock or fire, do not expose this unit

rain or moisture

• Do not spill water or other liquids into or on to your unit.

• Be sure that the local power outlet match that of the required volt-

age for your unit.

• Do not attempt to operate this unit if the power cord has been

frayed or broken.

• Do not attempt to remove or break off the ground prong from

the electrical cord. This prong is used to reduce the risk of electrical

shock and fire in case of an internal short.

• Disconnect from main power before making any type of connection.

• Do not remove the cover under any conditions. There are no user

serviceable parts inside.

• Never operate this unit when it’s cover is removed.

• Always be sure to mount this unit in an area that will allow proper

ventilation. Allow about 6” (15cm) between this device and a wall.

• Do not attempt to operate this unit, if it becomes damaged.

• This unit is intended for indoor use only, use of this product out-

doors voids all warranties.

• Always mount this unit in safe and stable matter.

• Power-supply cords should be routed so that they are not likely to

be walked on or pinched by items placed upon or against them,

paying particular attention to cords at plugs, convenience recep-

tacles, and the point where they exit from the appliance.

• Cleaning -The fixture should be cleaned only as recommended by

the manufacturer. See page 20 for cleaning details.

• Heat -This fixture should be situated away from heat sources such

as radiators, heat registers, stoves, or other appliances (including

amplifiers) that produce heat.

• The fixture should be serviced by qualified service personnel when:

A. Objects have fallen, or liquid has been spilled into the appliance.

B. The appliance has been exposed to rain or water.

C. The appliance does not appear to operate normally or exhibits

a marked change in performance.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 4

X-Move LED 25R Set Up

Power Supply: Before plugging your unit in, be sure the source voltage in your area matches the required voltage for your American DJ

®

X-Move LED 25R.The American DJ

®

X-Move LED 25R is available in a 120v and 220v version. Because line voltage may vary from venue to venue, you should be sure your unit voltage matches the wall outlet voltage before attempting to operate you fixture. Also be sure to only use the included I.E.C. power cable supplied with the unit, this cable matches the voltage and current requirements of the unit.

DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most lighting and controller manufactures as a form of

communication between intelligent fixtures and controllers. A DMX controller sends DMX data instructions from the controller to the fixture. DMX data is sent as serial data that travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals located on all DMX fixtures (most controllers only have a DATA “OUT” terminal).

DMX Linking: DMX is a language allowing all makes and models of different manufactures to be linked together and operate from a single controller, as long as all fixtures and the controller are DMX compliant. To ensure proper DMX data transmission, when using

SOUND

REMOTE

CONTROL

INPUT

INPUT OUTPUT

SOUND several DMX fixtures try to use the shortest cable path possible. The order in which fixtures are connected in a DMX line does not influence the DMX addressing. For example; a fixture assigned a DMX address of 1 may be placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the middle. Therefore, the first fixture controlled by the controller could be the last fixture in the chain. When a fixture is assigned a DMX address of 1, the DMX controller knows to send

DATA assigned to address 1 to that unit, no matter where it is located in the DMX chain.

Data Cable (DMX Cable) Requirements (For DMX

and Master/Slave Operation): The X-Move LED

25R can be controlled via DMX-512 protocol. The

X-Move LED 25R is a nine channel DMX unit. The

DMX address is set electronically using the controls on the front panel of the unit. Your unit and your DMX controller require a approved DMX-512

110 Ohm Data cable for data input and data output

1

2

3

Figure 1

COMMON

DMX +

DMX -

(Figure 1). We recommend Accu-Cable DMX cables. If you are making

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 5

3

1

2

REMOTE

CONTROL

INPUT

INPUT OUTPUT REMOTE

CONTROL

INPUT your own cables, be sure to use standard 110-120 Ohm shielded cable

(This cable may be purchased at almost all professional sound and lighting stores). Your cables should be made with a male and female

XLR connector on either end of the cable. Also remember that DMX cable must be daisy chained and cannot be split.

POWER POWER

Notice: Be sure to follow figures two and three when making your own cables. Do not use the ground lug on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the shield could cause a short circuit and erratic behavior.

XLR Male Socket

1 Ground

2 Cold

REMOTE

CONTROL

INPUT

INPUT OUTPUT

3 Hot

Figure 3

3

1

2

1

2

3

COMMON

DMX +

DMX -

XLR Female Socket

2 Cold 1 Ground

SOUND

3 Hot

3

1

2

XLR Pin Configuration

Pin 1 = Ground

REMOTE

CONTROL

INPUT

INPUT OUTPUT

Pin 2 = Data Compliment (negative)

Pin 3 = Data True (positive)

Figure 4

Figure 2

3

2

1

Special Note: Line Termination. When longer runs of cable are used, you may need to use a terminator on the last unit to avoid erratic behavior. A terminator is a 110-120 ohm 1/4 watt resistor which is connected between pins 2 and 3 of a male XLR connector (DATA + and

DATA -). This unit is inserted in the female XLR connector of the last unit in your daisy chain to terminate the line. Using a cable terminator

(ADJ part number Z-DMX/T) will decrease the possibilities of erratic behavior.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 6

SOUND

REMOTE

CONTROL

INPUT

INPUT OUTPUT

POWER

X-Move LED 25R Set Up

5-Pin XLR DMX Connectors. Some manufactures use 5-pin DMX-

512 data cables for DATA transmission in place of 3-pin. 5-pin DMX fixtures may be implemented in a 3-pin DMX line. When inserting standard 5-pin data cables in to a 3-pin line a cable adaptor must be used, these adaptors are readily available at most electric stores. The chart below details a proper cable conversion.

Conductor

Ground/Shield

Data Compliment (- signal)

Data True (+ signal)

Not Used

Not Used

3-Pin XLR to 5-Pin XLR Conversion

3-Pin XLR Female (Out)

Pin 1

Pin 2

Pin 3

5-Pin XLR Male (In)

Pin 1

Pin 2

Pin 3

Pin 4 - Do Not Use

Pin 5 - Do Not Use

X-Move LED 25R System Menu

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 7 American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 8

X-Move LED 25R System Menu

System Menu: When making adjustments you can press

ENTER to confirm your setup or you can wait 8 seconds for automatic setup. To exit without making any adjustments press the MENU button.

ADDR -

DMX Address Setting.

1. Tap the either the MENU, UP, or DOWN buttons until “ADDR” is displayed, press ENTER.

2. The current address will now be displayed and flashing.

Press the UP or DOWN buttons to find your desired address.

Press ENTER to set your desired DMX address.

SHND -

This will let you choose one of the four preprogrammed shows. See show descriptions below.

1. Tap the either the MENU button until “SHND” is displayed, press ENTER. Either “SH 1”, “SH 2”, “SH 3” or “SH 4” will be displayed.

2. Tap the UP or DOWN buttons to find you desired show and then press ENTER to confim and exit.

SHOWS:

Show 1 - For fixtures placed on the floor, the tilt movement angle is 210°

Show 2 - For fixtures fixed to the ceiling or truss, the tilt movement angle is 90°.

Show 3 - For fixtures placed on a table or stage. The beam is projected at the audience’s direction; i.e. in front of the stage.

Pan movement angle (left to right to left) is 160°. Tilt movement angle is 90°.

Show 4 - For fixtures fixed to the ceiling or truss. The beam is projected at the audience’s direction; i.e. in front of the stage.

Pan movement angle (left to right to left) is 160°. Tilt movement angle is 90°.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 9

X-Move LED 25R System Menu

SLND -

This will let you set unit as a master or slave in a master/slave configuration.

1. Tap the MENU button until “SLND” is displayed, press

ENTER. Either “SL 1” or “SL 2” will be displayed.

2. Tap the UP or DOWN buttons until your desired setting is displayed, press ENTER to confim.

NOTE: In a Master/Slave configuration you can set one fixture to Master and then set the next fixture to “SL 2”, the fixtures will now have contrast movement to each other.

SOUN -

Sound Active mode.

1. Tap the MENU button until “SOUN” is displayed, press

ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to activate sound active mode, or

OFF” to deactivate sound active mode.

3. Press ENTER to confirm.

BLND -

Blackout or Stand by mode.

1. Tap the MENU button until “BLND” is displayed, press

ENTER. Either Yes or No will be displayed.

2. To activate Blackout tap the UP or DOWN buttons until “Yes” is displayed, press ENTER to confim. The fixture will now be in

Blackout mode. To deactivate Blackout mode, select “No” and press Enter.

I PAN -

Pan Inversion

1. Tap the MENU button until “I PAN” is displayed, press ENTER.

Either NO or 1 will be displayed.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 10

X-Move LED 25R System Menu

2. To activate the Pan inversion tap the UP or DOWN buttons until I is displayed, press ENTER to confim. To deactivate Pan inversion, select No and press Enter.

I TLT -

Tilt Inversion

1. Tap the MENU button until “I TLT” is displayed, press ENTER.

Either NO or 1 will be displayed.

2. To activate the Tilt inversion tap the UP or DOWN buttons until I is displayed, press ENTER to confim. To deactivate Tilt inversion, select No and press Enter.

LED -

With this function you can have the LED display turn off after 10 seconds.

1. Tap the MENU button until “LED” is displayed, press ENTER.

2. The display will show either “ON” or “OFF”. Press the UP or

DOWN buttons to select “ON” to keep the LED display on at all times, or “OFF” to switch to have the LED display switch off after 10 seconds.

3. Press ENTER to confirm. To make you LED display reappear again press any button.

DISP -

This function will reverse the display 180º.

1. Tap the MENU button until “DISP” is displayed, press ENTER.

2. Press ENTER to “flip” the display. Press ENTER to “flip” it again. Press ENTER when you have made your desired setup.

FADJ

- This function will allow you to focus the lens for a clear LED output.

1. Tap the MENU button until “FADJ” is displayed, press

ENTER. The fixture will turn a different way each time the

ENTER button is pressed.

2. With the spot pointed at a flat wall or surface, at the distance

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 11

X-Move LED 25R System Menu it will be set up, you can turn the lens to adjust the clarity. Press

MENU to exit.

TEST

- This function will run a self test program. The test program will test pan/tilt movement and colors.

1. Tap the MENU button until “TEST” is displayed, press ENTER.

2. The fixture will now run a self test.

TEMP

- With this function you can check the temperature of the fixture.

1. Tap the MENU button until “TEMP” is displayed, press ENTER.

2. The temperature of the fixture will now be displayed. Press

MENU to exit.

FHRS

- With this function you can display the running time of the unit.

1. Tap the MENU button until “FHRS” is displayed, press

ENTER.

2. The running time of the fixture will now be displayed. Press

MENU to exit.

VER

- With this function you can display the version software of the unit.

1. Tap the MENU button until “VER” is displayed, press ENTER.

2. The software version will now be displayed. Press MENU to exit

RSET

- Use this function to reset the unit.

1. Tap the MENU button until “RSET” is displayed, press ENTER.

2. The fixture will now reset,

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 12

X-Move LED 25R System Menu

MENU

To enter the OTIL (Home position adjustment) & Gobo wheel adjustment submenu, press the ENTER button for at least 5 seconds. In this submenu you are able to adjust the original position of the gobo wheel and tilt (home position).

OTIL

- Adjustment of the home position.

1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “OTIL” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit.

OGOB

- Adjustment of the gobo wheel.

1. Press the ENTER button for at least 5 seconds, then press the UP or DOWN buttons so that “OGOB” is displayed, press ENTER.

2. Use the UP and DOWN buttons to make your adjustments, and then press ENTER to confirm. Press the MENU button for one second to exit.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 13

X-Move LED 25R Operation

Operating Modes: The X-Move LED 25R can operate in three different modes. In each mode you can run the fixture as a stand alone fixute or in a master/slave confiugration. This next section will detail the differences in the operating modes.

• Sound Active mode -

The fixture will react to sound, chasing through the built-in programs.

• Show mode -

The fixture will run one of four shows that you choose.

• DMX control mode -

This function will allow you to control each individual fixtures traits with a standard DMX-512 controller such as the Elation

®

Show

Designer.

Master-Slave Operation This function will allow you to link up to 16 units together and operate without a controller. The units will be sound activated. In Master-Slave operation one unit will act as the controlling unit and the others will react to the controlling units programs. Any unit can act as a Master or as a Slave.

1. Using approved DMX data cables, daisy chain your units togeth-

er via the XLR connector on the rear of the units. Remember the

Male XLR connector is the input and the Female XLR connector

is the output. The first unit in the chain (master) will use the female

XLR connector only - The last unit in the chain will use the male

XLR connector only. For longer cable runs we suggest a termina-

tor at the last fixture.

2. On the Master unit find your desired show and set that show by

pressing the ENTER button.

3. On the slave units tap the MENU button until “SLND” is dis-

played, and Press ENTER. Choose either “SL 1” or “SL 2” and

press ENTER. See page 10 for more info.

4. The slave units will now follow the Master unit.

Universal DMX Control: This function allows you to use a Elation

® universal DMX-512 controller to control the chases and patterns, dimmer and strobe. A DMX controller allows you to create unique programs tailored to your individual needs.

1. The X-Move LED 25R is a nine DMX channel DMX fixture. See

pages 16-17 for detailed description of the DMX values and traits.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 14

X-Move LED 25R Operation

2. To control your fixture in DMX mode, follow the set-up procedures

on pages 5-7 as well as the set-up specifications that are includ-

ed with your DMX controller.

3. Use the controller’s faders to control the various DMX fixture traits.

4. This will allow you to create your own programs.

5. Follow the instruction on page 9 to set the DMX address.

6. For longer cable runs (more than a 100 feet) use a terminator on

the last fixture.

7. For help operating in DMX mode consult the manual included

with your DMX controller.

Sound Active Mode: This mode allows either single unit or several units linked together, to run to the beat of the music.

1. Tap the MENU button until “SOUN” is displayed, and press

ENTER. Tap the UP or DOWN buttons so that “ON” is dis

played and press ENTER.

2. The optional UC3 Controller (not included) may be used to con-

trol different functions including blackout.

Show Mode: This mode allows either a single unit or several units linked together, to run one of four shows that you choose.

1. Tap the MENU button until “SHND” is displayed, and press

ENTER.

2. Tap the UP or DOWN buttons until you find your desired show,

and press ENTER.

X-Move LED 25R UC3 Control

The optional UC3 Controller (not included) may be used to con- trol different functions including blackout.

Stand By

Function

Mode

Blackout the unit

1. Sync. Strobe

2. Async strobe

3. Sound Strobe

Sound (LED OFF)

Show

1-4

Show (LED

Slow Blinking)

1. Select Color

2. Select Gobo

LED ON

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 15

X-Move LED 25R DMX Traits

Channel Value Function

1 0 - 255 PAN

2 0 - 255 TILT

3 COLORS

0 - 14 WHITE

15 - 29 RED

30 - 44 BLUE

45 - 59 GREEN

60 - 74 YELLOW

75 - 89 PINK

90 - 104 LIGHT BLUE

105 - 119 LIGHT GREEN

120 - 127 LIGHT YELLOW

128 - 254 RAINBOW EFFECT SLOW - FAST

255 SOUND ACTIVE

4 GOBO WHEEL

0 - 9 OPEN

10 - 18 GOBO 1

19 - 27 GOBO 2

28 - 36 GOBO 3

37 - 46 GOBO 4

47 - 55 GOBO 5

56 - 63 GOBO 6

64 - 73 OPEN SHAKE

74 - 82 GOBO 1 SHAKE

83 - 91 GOBO 2 SHAKE

92 - 100 GOBO 3 SHAKE

101 - 110 GOBO 4 SHAKE

111 - 119 GOBO 5 SHAKE

120 - 127 GOBO 6 SHAKE

128 - 254 GOBO WHEEL ROTATION SLOW - FAST

255 SOUND ACTIVE

5 GOBO ROTATION

0 - 9 STOP

10 - 120 CLOCKWISE FAST - SLOW

121 - 134 STOP

135 - 247 COUNTER-CLOCKWISE SLOW - FAST

248 - 255 STOP

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 16

X-Move LED 25R DMX Traits

Channel Value Function

6 SHUTTER/STROBE

0 - 7 BLACKOUT

8 - 15 SHUTTER OPEN

16 - 131 STROBING SLOW - FAST

132 - 139 SHUTTER OPEN

140 - 181 SHUTTER SLOW OPEN - FAST CLOSE

182 - 189 SHUTTER OPEN

190 - 231 SHUTTER FAST OPEN - SLOW CLOSE

232 - 239 SHUTTER OPEN

240 - 247 RANDOM STROBE

248 - 255 SHUTTER OPEN

7 0 - 255 DIMMER 0% - 100%

8 MOVING HEAD MOVEMENT

0 - 7 NO FUNCTION

8 - 28 MOVEMENT 1

29 - 49 MOVEMENT 2

50 - 70 MOVEMENT 3

71 - 91 MOVEMENT 4

92 - 112 MOVEMENT 5

113 - 133 MOVEMENT 6

134 - 154 MOVEMENT 7

155 - 175 MOVEMENT 8

176 - 196 MOVEMENT 9

197 - 217 MOVEMENT 10

218 - 238 MOVEMENT 11

239 - 255 MOVEMENT 12

9 0 - 255 MOVEMENT SPEED FAST - SLOW

X-Move LED 25R Gobo Replacement

This unit comes with interchangable gobos. When changing the gobos please be very careful. Follow the instructions below, and see the figure pictures on the next page.

Caution! Never open the unit when in use. Always disconnect the main power before attempting to change the gobos.

1. To change the gobo, you must remove the top half of the

moving head. The top half of the moving head does not

have the lens attached to it. The lens is on the top half of the

head.

2. Unscrew the 3 phillips screws that secure the top half of the

head. Remove the top half of the head.

3. When you remove the shell you will be able to access the

gobo wheel (see picture below). Rotate the head so that the

lens is aimed up. Turn the gobo wheel with your hand until

you find the gobo you would like to change.

4. Using a pair of needle nose pliers, grab the fixture ring that

holds the gobo in place and remove the ring.

5. Once the ring is removed, rotate the head upside down so

that the gobo falls into your hand.

6. Carefully insert your new gobo and insert the fixture ring.

7. Reassemble the unit.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 17 American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 18

X-Move LED 25R Photometric Chart

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 19

X-Move LED 25R Fuse Replacement

Locate and remove the unit’s power cord. Once the cord has been removed located the fuse holder located inside the power socket.

Insert a flat-head screw driver into the power socket and gently pry out the fuse holder. Remove the bad fuse and replace with a new one.

The fuse holder has a built-in socket for a spare fuse be sure not to confuse the spare fuse with active fuse.

X-Move LED 25R Cleaning

Due to fog residue, smoke, and dust cleaning the internal and external optical lenses and mirror should be carried out periodically to optimize light output. Cleaning frequency depends on the environment in which the fixture operates (I.e. smoke, fog residue, dust, dew). In heavy club use we recommend cleaning on a monthly basis.

Periodic cleaning will ensure longevity, and crisp output.

1. Use normal glass cleaner and a soft cloth to wipe down the out-

side casing.

2. Use a brush to wipe down the cooling vents and fan grill.

3. Clean the external optics with glass cleaner and a soft cloth every

20 days.

4. Clean the internal optics with glass cleaner and a soft cloth every

30-60 days.

5. Always be sure to dry all parts completely before plugging the unit

back in.

X-Move LED 25R Trouble Shooting

Trouble Shooting: Listed below are a few common problems that you may encounter, with solutions.

No light output from the unit;

1. Be sure you have connected your unit into a standard 120v wall

outlet.

2. Be sure the external fuse has not blown. The fuse is located on

the rear panel of the unit.

3. Be sure the fuse holder is completely and properly seated.

Unit does not respond to sound;

1. Low frequencies (bass) should cause the unit to react to sound.

Tapping on the microphone, quiet or high pitched sounds may

not activate the unit.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 20

X-Move LED 25R Warranty

MANUFACTURER’S LIMITED WARRANTY

A. American DJ, Inc. hereby warrants, to the original purchaser, American DJ and American

Audio products to be free of manufacturing defects in material and workmanship for a prescribed period from the date of purchase (see specific warranty period on reverse). This warranty shall be valid only if the product is purchased within the United States of America, including possessions and territories. It is the owner’s responsibility to establish the date and place of purchase by acceptable evidence, at the time service is sought.

B. For warranty service you must obtain a Return Authorization number (RA#) before sending back the product. Contact American DJ, Inc. Service Department at 800-322-6337. Send the product only to the American DJ, Inc. factory. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warranty,

American DJ, Inc. will pay return shipping charges only to a designated point within the United

States. If the entire instrument is sent, it must be shipped in it’s original package. No accessories should be shipped with the product. If any accessories are shipped with the product, American DJ,

Inc. shall have no liability whatsoever for loss of or damage to any such accessories, nor for the safe return thereof.

C. This warranty is void if the serial number has been altered or removed; if the product is modified in any manner which American DJ, Inc. concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ,

Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the product is damaged because not properly maintained as set forth in the instruction manual.

D. This is not a service contract, and this warranty does not include maintenance, cleaning or periodic check-up. During the period specified above, American DJ, Inc. will replace defective parts at its expense with new or refurbished parts, and will absorb all expenses for warranty service and repair labor by reason of defects in material or workmanship. The sole responsibility of American DJ, Inc. under this warranty shall be limited to the repair of the product, or replacement thereof, including parts, at the sole discretion of American DJ. All products covered by this warranty were manufactured after January 1, 1990, and bear identifying marks to that effect.

E. American DJ, Inc. reserves the right to make changes in design and/or improvements upon its products without any obligation to include these changes in any products theretofore manufactured. No warranty, whether expressed or implied, is given or made with respect to any accessory supplied with products described above. Except to the extent prohibited by applicable law, all implied warranties made by American DJ, Inc. in connection with this product, including warranties of merchantability or fitness, are limited in duration to the warranty period set forth above. And no warranties, whether expressed or implied, including warranties of merchantability or fitness, shall apply to this product after said period has expired. The consumer’s and/or Dealer’s sole remedy shall be such repair or replacement as is expressly provided above; and under no circumstances shall American DJ, Inc. be liable for any loss or damage, direct or consequential, arising out of the use of, or inability to use, this product.

This warranty is the only written warranty applicable to American DJ and American Audio

Products and supersedes all prior warranties and written descriptions of warranty terms and conditions heretofore published.

MANUFACTURER’S LIMITED WARRANTY PERIODS:

• All American Audio Products = 1-year (365 day) Limited Warranty (except V-Plus Series Amplifiers)

• All American Audio V-Plus Series Amplifiers = 3-year (1095 day) Limited Warranty

• American DJ Lighting and American DJ Branded Products = 1-year (365 day) Limited Warranty

(Such as: Special Effect Lighting, Intelligent Lighting, UV lighting, Strobes, Fog Machines, Bubble

Machines, Mirror Balls, Par Cans, Trussing, Lighting Stands etc. excluding Laser Products, lamps, and Star Tec Series)

• American DJ Laser Products and Star Tec Products = 90-Day Limited Warranty

• American DJ L.E.D. Products = 3-year (1095 day) Limited Warranty (excluding motors, PCB

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 21

X-Move LED 25R Notes

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 22

X-Move LED 25R Specifications

Model: X-Move LED 25R

Voltage*:

LED:

120v/60Hz or 230v/50Hz

1 x 25W CREE LED

Power Consumption: 75W

Dimensions: 8.75”(L) x 8”(W) x 12.75”(H)

Beam Angle:

Colors:

Weight:

221mm x 202mm x 320mm

17 Degree

RGB + White

14 Lbs. / 6.2 kgs.

2

Duty Cycle:

DMX:

None

9 DMX Channels

Colors: 8 + White

Gobos: 6 + Spot

23.8mm/0.2mm thickness

(19mm viewable)

Sound Active: Yes

Working Position:

Warranty:

*Voltage is user selectable

Any Safe, Secure Position

3 Year (1095 days)

Please Note:

Specifications and improvements in the design of this unit and this manual are subject to change without any prior written notice.

American DJ ® - www.americandj.com - X-Move LED 25R Instruction Manual Page 23

©American DJ Supply

American DJ World Headquarters:

6122 S. Eastern Ave. Los Angeles, CA 90040 USA

Tel: 323-582-2650 / Fax: 323-725-6100

Web: www.americandj.com / E-mail: [email protected]

American DJ Europe

Junostraat 2

6468 EW Kerkrade

Netherlands [email protected] / www.americandj.eu

Tel: +31 45 546 85 00 / Fax: +31 45 546 85 99

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement