E85509-00
FIBERPRO
®
CARPET
SPOTTER
3.5 Gallon
Carpet Spotter
Machine
Operator and Parts
Manual
1001 Brown Avenue • Toledo, Ohio 43607-0127
Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com
1
2
TABLE OF CONTENTS
SAFETY ......................................................................... 3
MACHINE OPERATION .............................................4 - 5
MACHINE DIAGRAM AND PARTS LISTING ..............6 - 7
WARRANTY ................................................................... 8
IMPORTANT SAFETY INSTRUCTIONS
*When using a commercial spotter, basic precautions should be followed, including the following:
*Read all instructions before using this commercial spotter.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
WARNING
To reduce risk of fire, electric shock, or injury:
• Do not use outdoors or on wet surfaces.
• Do not leave commercial spotter unattended when plugged in. Turn off the switch and unplug the electrical cord when not in use and before servicing.
• Do not allow to be used as a toy. Close attention is necessary when used near children.
• Use only as described in this manual. Use only manufacturer’s recommended attachments.
• Do not use with damaged cord or plug. If commercial spotter is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to a service center before using.
• Do not pull or carry by cord, use cord as a handle, close a door on cord, or pull a cord around sharp edges or corners. Do not run commercial spotter over cord. Keep cord away from heated surfaces.
• Do not use extension cords or outlets with inadequate current carrying capacity.
• Turn off all controls before unplugging.
• Do not handle plug or commercial spotter with wet hands.
• Do not put any objects into openings. Do not use with any opening blocked, keep free of dust, lint, hair, and anything that may reduce airflow.
• Keep hair, loose clothing, fingers, and all parts of body away from openings and moving parts.
• Do not pick up anything that is burning or smoking, such as cigarettes, matches or hot ashes. Use extra care when cleaning on stairs. Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
• Store your commercial spotter indoors in a cool, dry area.
• Do not unplug by pulling on cord. To unplug, grasp the plug, NOT THE CORD.
THESE MODELS ARE GROUNDED, CONNECT TO A PROPERLY GROUNDED OUTLET ONLY - SEE GROUNDING INSTRUCTIONS.
GROUNDING INSTRUCTIONS
This appliance must be grounded. If it should malfunction or breakdown, grounding provides a path of least resistance for electric current to reduce the risk of shock. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be inserted into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the outlet is properly grounded. Do not modify the plug provided with the appliance - if the plug will not fit the outlet, have a proper outlet installed by a qualified electrician.
This appliance is for use on a normal 120 volt circuit, and has a grounded plug that looks like the plug illustrated in sketch A.
Note: In Canada, the use of a temporary adapter is not permitted by the Canadian Electrical Code.
3
4
Check the carton carefully for signs of rough handling. Remove the machine from the carton. If the machine is damaged, notify the carrier immediately and request an inspection. Be sure to keep the carton, packing inserts, packing lists and carrier receipt until the inspector has verified your claim.
Liability ceases when the shipment is picked up by the carrier, but our customer service staff will be glad to furnish any information needed in connection with the claim and will expedite the repair of the machine.
Operating Instructions for Commercial Spotter
WHEN THE MACHINE IS DELIVERED…
BEFORE USING THE MACHINE shown on the nameplate of the machine.
Do not attempt to plug a 115 volt machine into a 230 volt outlet or a 230 volt machine into a
115 volt outlet.
Disconnect the power cord from the outlet before attempting maintenance or repair work.
Do not leave machine connected to an electrical outlet when unattended.
Never pull the machine by the cord or yank the cord from the receptacle. Replace a damaged cord immediately.
If an extension cord is necessary, use a three conductor grounding cord – 12 gauge wire or heavier to prevent motor burnout and over-heating of wires.
To avoid electric shock, do not expose to rain.
Store indoors.
To avoid fire, do not use machine in environments where combustible liquids, vapors or dust concentrations are present.
Read the manual carefully and completely before attempting to operate the unit. This manual has important information for the use and safe operation of this machine. Keep this manual handy at all times. The commercial spotter will provide years of satisfactory service if operated and maintained according to recommendations in the manual.
WARNING card back.
WARRANTY
To protect your investment, promptly fill in the required information on the warranty card included with the unit. Then mail the
GENERAL PRECAUTIONS
Follow these guidelines to ensure operator safety and to maintain equipment in running order.
Make sure the machine is plugged into an electrical outlet with the same voltage rating as
Do not expose the machine to freezing temperatures.
Do not use the machine for totally dry vacuuming. This machine is not fitted with a fine dust filter.
Do not use citrus-based cleaners in this machine.
Do not use cleaning chemicals in this machine except those recommended for commercial extraction equipment. The use of any chemical with abrasive additives voids the warranty.
Do not break off or pull out the ground prong on the plug.
Do not attempt repair on a warranted machine unless instructions to perform it by an authorized shop are obtained from the factory.
Do not use any replacement parts except those specified on the parts list. Proper performance of the machine could be affected if substitutions are made.
Use defoamer at all times to prevent damaging the vacuum motor.
Do not use water in excess of 140° F (62° C).
Failure to comply with the above warning instructions will void the warranty.
Operating Instructions for Commercial Spotter
Filling the Spotter
Disconnect the solution and recovery tanks. Add water and or chemicals to the lower solution tank. The tank will hold up to 3.5 gallons.
Operating the Spotter
A. Attach the solution feed line to the quick disconnect at the bottom of the machine.
B. Attach the vacuum hose to the vacuum inlet (handle) above the recovery tank lid.
Disconnect tanks
C. Turn the 3-way switch to use either the pump and vacuum or the vacuum alone.
(Allow approximately 30 seconds for the pump to prime.)
D. Use the hand tool to spray and recover the solution.
E. The float shut-off will disable the suction of the unit when the recovery tank is full. The operator will notice a distinctive change in the sound of the vacuum motor when the shut-off is activated. Empty the recovery tank to resume cleaning.
Emptying the Recovery Tank
A. Disconnect the solution line and vacuum hose.
B. Unlatch the recovery tank from the base of the unit and remove.
C. Remove the drain plug.
D. Drain tank over suitable outlet for wastewater.
E. Rinse tank after each use.
Drain plug
Attach vacuum hose
3-way switch
Attach solution hose
Basic Troubleshooting:
A. If the pump does not prime, depress the lever on the hand tool to release the air lock.
B. If solution flow is reduced or spray is weak:
1. Check for low solution level in the solution tank.
2. Check the screen on the hose in the solution tank for blockage.
3. Check the spray jet in the hand tool for blockage.
If suction is low:
1. Check the recovery tank to see if it is full.
2. Check for blockage in the hand tool or the hose.
3. Add defoamer to recovery tank.
5
6
Parts Diagram
Parts List ref. # order # description
1 85558 CASTER SWIVEL 45MM
2 85559 SCREW 1/4-20 X 1/2" PHIL. STAINLESS STEEL
3 85169 WASHER 1/4 MED SPLIT LOCK ZINC
4 85082 SCREW, 8-32 X 1/4", THPH, BLACK
5 85565 LATCH OVER CENTER W/ KEEPER
6 85566 HANDLE / WHEEL ASSEMBLY
7 85567 GASKET SOLUTION TANK
8 85568 GASKET DONUT 3/8" THICK
9 85569 NUT, LOCK, DIE CAST, 1-1/2"
10 85635 DAMP VALVE GASKET 1-1/2" THIN
11 85150 SCREW 8-32 X 1/2" PAN HEAD PHILLIPS
12 85577 PLUG 7/8" X 1-1/16" SNAP-TITE
13 85578 BULKHEAD 1-1/2" MPT X 1-1/2"
14 85579 1-1/2" PVC SCHEDULE 40 PIPE
15 85580 FLOAT RING VACUUM SHUT-OFF
16 82010 GASKET, LID, 6" O.D. X 4.6" I.D.
17 82009 LID 4" CLEAR W/ BLACK RING
18 85584 WASHER #6 X 5/8 SAE FLAT 55
19 85585 SCREW 8-18 X 1/2 PAN HD PHIL SS
20 85586 SHUT-OFF DISK
21 85148 SCREW #8 X 3/4" PHILLIPS FLAT TS
22 85587 FITTING 1/8" NPTM X 1/4 HOSE BARB ref. # order #
23
24
25
26
27
28
29
30
31
32
33
34
35
85585
36 85626 description
85588 WASHER 5/8" X 1-3/16" NEOPRENE BOND
85589 ANCHOR CONECTOR 1/8"
85618 FITTING ELBOW 90 DEGREE 1/4-1/8
85753 HOSE 1/4" BRAIDED
85636 FILTER, MESH SCREEN
85619 FITTING 1/4 NPTM X 1/4 HOSE BARB
85620 CORD HOOK
85046 SCREW 10-24 X 1/2"
85621 END LOOP STAINLESS STEEL W/ TWO HOLES
85622 12" STAINLESS STEEL JACK CHAIN
SCREW, 8-18 X 1/2" PHILLIPS PAN
85624 SCREW 1/4-20 X 1" SHCS
85625 SOLUTION TANK
RECOVERY TANK
37 85627 CLIP, SPRING, BLACK VINYL COATED
38 85633 FILTER, FOAM, 1-1/2" O.D. X 1/2" THICK
39 85628 CLAMP 1/4" WORM GEAR STAINLESS STEEL
Not Illustrated
85522 SOLUTION HOSE ONLY
83092 HAND TOOL, DETAILER ASSEMBLY 1-1/2"
85520 Vac/Sol.Hose Assembly
85521 VACUUM HOSE ONLY
Motor Assembly ref. #
1 order # description
83219 BASE PLATE WELDMENT SPOTTER
2 85399 WASHER 3/8" FLAT STAINLESS STEEL
3 85618 BARB ELBOW (90) 1/4-1/8 BRASS
4 85753 HOSE 1/4" BRAIDED
5 85169 WASHER 1/4 MED SPLIT LOCK ZINC
6 85623 CAP SVREW 1/4-20 X 5-1/2" ZINC
7 83203 STRAIN RELIEF 1/2" NPT
8 85629 SWITCH ROCKER SPOTTER
9 85564 POWER CORD, 18/3 X 15'
10 85631 CLAMP 1/4" WORM GEAR STAINLESS STEEL
11 85637 FITTING NYLON, 90 DEG. ELBOW
12 85649 MOUNT, FLOJET PUMP, SPOTTER
13 85553 PUMP, OSCILLATING, FLOJET
14 85763 HOSE 1/4" BRAIDED
15 85651 ref. # order # description
16 85587 FITTING, 1/8 NPTM X 1/4 HOSE BARB
17 85358 NUT, 1/4-20, LOCK NYLON INSERT
18 85652 VACUUM MOTOR GASKET
19 85653 SCREEN VACUUM MOTOR
20 85684 MOTOR, VACUUM, IMPERIAL ELECTRIC
21 85654 1-1/2" WIRE REINFORCED HOSE
22 85655 MOUNTING POST VACUUM MOTOR
23 82005 MALE QUICK DISCONNECT
24 85046 SCREW 10-24 X 1/2" PHILLIPS TRUSS HEAD
25 85656 NUT SPEED 1/4-20 U TYPE CLIP
26 85657 WASHER NYLON .50 ID X .75 OD X .13 THK.
Not Illustrated
X8284 SCREW 8-32 X 3/8 PHIL PANTCS
83215 NUT 1/2" CONDUIT
PX215
X8497B
CLAMP 2-1/2" WORM GEAR S.S.
SWITCH LABEL 2.5" X 1.5"
7
10 year coverage
BETCO US WARRANTY POLICY
3 Year Coverage 1 Year Coverage
Subject to the conditions stated below,
Betco warrants parts and labor on rotationally molded polyethylene tanks/ housings and injection molded vacuum head assemblies to be free from defects in materials and workmanship for a period of ten years to the original purchaser.
Subject to the conditions stated below,
Betco warrants parts and labor on all other Betco components to be free from defects in materials and workmanship for a period of three years to the original purchaser.
Subject to the conditions stated below,
Betco offers a limited warranty on parts and labor on the following equipment: parts and accessories to be free from defects in materials and workmanship for a period of one year to the original purchaser.
• PowerUp ™ 14 Upright Vacuum:
#E29990-00
• Bac Pac Lite Vacuum: #85903-00
• FiberPRO ® Floor Dryer: #85507-00
• WORKMAN ™ Series Vacuums:
#85024-00, #85025-00, #83012-00,
#85027-00
• All Tools and Accessories
• All Battery Chargers
• All Batteries are pro-rated for 1 year
Allowable Travel Time Warranty Reimbursement:
Eligible equipment: All battery and propane powered equipment products. Warranty period: 90 days from date of sale to the original purchaser. A maximum 180 mile round trip at 50 cents per mile will be allowed for warranty consideration.
Propane Machine Warranty:
Kawasaki engines are warranted by Kawasaki for a period of 2 years against manufacturer defects. All other components
(except wear items)* are warranted by Betco for a period of 3 years.
*Wear Items exempt from Warranty consideration include but may not be limited to: power cords, transport wheels, vacuum bags, belts, squeegee blades, pad drivers, clutch plates, handle grips, filters, screens, throttle cables, brushes and carbon brushes.
Subject to the conditions and exceptions stated in this warranty, Betco warrants the Betco products to be free from defects in material and workmanship, under normal use and service, for the periods listed under the warranty policy to the original purchaser. At any time during the warranty period, Betco will furnish replacement parts for the Betco parts to the original purchaser. Such parts will be furnished and charged including transportation costs, to the original owner through any Betco authorized
Service Distributor. If the original part is returned within the warranty policy period from date of delivery for inspection by
Betco and is found to be defective the owner will be credited for the cost of replacement parts plus shipping and handling.
Replacement parts that have become defective through wear or abuse are not included in this warranty.
This warranty does not apply to damage or defect caused by accident, misuse. Negligence, fire, or to any Betco product which has been serviced or repaired by other than an authorized Betco Service Distributor or Betco factory personnel. This warranty is void if products are used for any purpose other than that which was intended. There are no other warranties expressed or implied. In no event shall Betco be liable for incidental or consequential damages or any damage to person or property. (Please note some states do not allow the exclusion or limitations for incidental and consequential damages).
8
1001 Brown Avenue • Toledo, Ohio 43607-0127
Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com
92284-92 Sept15C
