ET900
ET900
Intel ® CoreTM Duo/Solo 945GM
COM Express (Type II) CPU Module
USER’S MANUAL
Version 1.0
Acknowledgments
Award is a registered trademark of Award Software International,
Inc.
PS/2 is a trademark of International Business Machines
Corporation.
Intel and Celeron are registered trademarks of Intel Corporation.
Microsoft Windows is a registered trademark of Microsoft
Corporation.
Winbond is a registered trademark of Winbond Electronics
Corporation.
All other product names or trademarks are properties of their
respective owners.
Attention:
Before installing the CPU heat sink, remove the two protective
sheaths as shown in the figure below.
Note:
Remove the protective
sheath before installation.
ii
ET900 User’s Manual
Table of Contents
Introduction ....................................................... 1
Product Description ............................................................. 1
Checklist .............................................................................. 2
ET900 Specifications .......................................................... 3
Dimensions .......................................................................... 4
Installing the Processor ....................................................... 5
Installing the Memory ......................................................... 6
Connectors on ET900 .......................................................... 7
J2, J3: COM Express Type 2 Connectors ............................ 7
BIOS Setup ....................................................... 11
Drivers Installation ...................................... 35
Intel Chipset Software Installation Utility......................... 36
VGA Drivers Installation .................................................. 38
AC97 Codec Audio Driver Installation (IP400 carrier board
only) .................................................................................. 40
Intel PRO LAN Drivers Installation .................................. 42
Marvell LAN Drivers Installation (IP400 carrier board only)
........................................................................................... 43
ET900 User’s Manual
iii
The ET900 945GM COM Express CPU Module
iv
ET900 User’s Manual
INTRODUCTION
Introduction
Product Description
The ET900 board incorporates the Mobile Intel® 945GM Express
Chipset for Embedded Computing, consisting of the Intel® 945GM
Graphic Memory Controller Hub (GMCH) and Intel® I/O Controller
Hub 7-M (ICH7-M), an optimized integrated graphics solution with a
533MHz and 667MHz front-side bus. Dimensions of the board are
95mm x 125mm.
The integrated powerful 3D graphics engine, based on Intel® Graphics
Media Accelerator 950 (Intel® GMA 950) architecture, operates at core
speeds of up to 400 MHz. It features a low-power design and is validated
with the Intel® Core Duo/Solo on 65nm process. With DDR2 667MHz
SO-DIMM socket on board, the board supports up to 2GB of DDR2
system memory.
Intel® Graphics Media Accelerator 950 supports a unique intelligent
memory management scheme called Dynamic Video Memory
Technology (DVMT). DVMT handles diverse applications by providing
the maximum (224MB) availability of system memory for general
computer usage, while supplying additional graphics memory when a
3D-intensive application requests it. The Intel GMA 950 graphics
architecture also takes advantage of the high-performance Intel
processor. Intel GMA 950 graphics supports Dual Independent Display
technology.
The main features of the board are:
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
ƒ
Supports COM ETX Type II Module pin-out definitions
Supports Intel® CoreTM Duo/Solo processors
Supports up to 533/667MHz FSB
One DDR2 SDRAM SO-DIMM, Max. 2GB
Intel® 945GM Express VGA for CRT / LVDS
Intel® 945GM Integrated VGA; Supports CRT / LVDS
Supports up to six x1 PCI-E, one x16 PCI-E, four PCI
ET900 User’s Manual
1
INTRODUCTION
Checklist
Your ET900 package should include the items listed below.
• The ET900 CPU Module
• This User’s Manual
• 1 CD containing the following:
• Chipset Drivers
• Flash Memory Utility
2
ET900 User’s Manual
INTRODUCTION
ET900 Specifications
COM-ETX w/ Pin-Out Type 2
Intel Core Duo/Solo Mobile Processors
0.700V ~ 1.5V
Up to 1.66GHz or above
533MHz/667MHz FSB
Form Factor
CPU Type
CPU Voltage
System Speed
CPU Operate
Frequency
Cache
Green /APM
CPU Socket
Chipset
BIOS
Memory
VGA
LVDS
TV-Out
LAN
USB 2.0
Serial ATA Ports
Parallel IDE
Audio
Connector to
Carrier Board
Watchdog Timer
System Voltage
Other
Board Size
2MB
APM1.2
BGA CPU on board / mPGA 478MT Socket
Intel 945GM Chipset
GMCH: 82945GM 1466-pin FCBGA
ICH7M: 82801GBM 652-pin mBGA FWH
Award BIOS, support ACPI Function
DDR2 667/533 SO-DIMM x1 (w/o ECC
function), Max. 2GB
945GM built-in, supports CRT/S-VIDEO
945GM built-in, supports 18+18 bits, single or
dual channel LVDS
Support TV-Out (Composite) and S-Video
ICH7M built-in 10/100BT MAC + Intel
EP82562ET PHY
ICH7M built-in USB 2.0 host controller, support
8 ports
ICH7M built-in SATA controller, supports 2
ports
ICH7M built-in one channel Ultra DMA
33/66/100
ICH7M Built-in Audio controller (AC97 Codec
at carrier board)
Two 220-pin connectors (A-B & C-D)
Yes (256 segments, 0, 1, 2…255 sec/min)
+5V, +3.3V, +12V, 5VSB
Modem Wakeup, LAN Wakeup
95mm x 125mm
ET900 User’s Manual
3
INTRODUCTION
Dimensions
4
ET900 User’s Manual
INTRODUCTION
Installing the Processor
The ET900 is available with a processor socket on board or with an
Intel® processor on board. In the case that your ET900 comes a Socket
479 processor socket for Intel® Pentium® M or Celeron® M processors,
follow the instructions below regarding the processor installation.
The processor socket comes with a screw to secure the processor. As
shown in the left picture below, loosen the screw first before inserting
the processor. Place the processor into the socket by making sure the
notch on the corner of the processor corresponds with the notch on the
inside of the socket. Once the processor has slide into the socket, fasten
the screw. Refer to the figures below.
NOTE: Ensure that the CPU heat sink and the CPU top surface are in
total contact to avoid CPU overheating problem that would
cause your system to hang or be unstable.
ET900 User’s Manual
5
INTRODUCTION
Installing the Memory
The ET900 COM Express CPU module accommodates 200-pin
DDR2-533 and DDR2-667 SODIMM memory modules with capacities
up to 1GB. Non-ECC is supported.
Installing and Removing Memory Modules
To install the DDR2 modules, locate the memory slot on the board and
perform the following steps:
1. Hold the DDR2 module so that the key of the DDR2 module align
with those on the memory slot. Insert the module into the socket at a
slight angle (approximately 30 degrees). Note that the socket and
module are both keyed, which means that the module can be installed
only in one direction.
2. To seat the memory module into the socket, apply firm and even
pressure to each end of the module until you feel it slip down into the
socket.
3. With the module properly seated in the socket, rotate the module
downward. Continue pressing downward until the clips at each end
lock into position.
4. To remove the DDR2 module, press the clips with both hands.
6
ET900 User’s Manual
INTRODUCTION
Connectors on ET900
J2, J3: COM Express Type 2 Connectors
The Type 2 connectors come in two 220-pin 0.5mm pitch receptacles.
They include PCI, IDE, GBE and up to 22 general-purpose PCIE lanes
(PCIE 0-5 and PCIE 16-31). For most Type 2 implementations, it is
expected that PCIE lanes 16-31 are used for graphics. Hence they are
designated PEG lanes 0-15 in the following table. Modules
implementing Pin out Type 2, such as the ET900, uses the pin-out
shown.
ET900 User’s Manual
7
INTRODUCTION
Pin
A1
A2
A3
A4
A5
A6
A7
A8
A9
A10
A11
A12
A13
A14
A15
A16
A17
A18
A19
A20
A21
A22
A23
A24
A25
A26
A27
A28
A29
A30
A31
A32
A33
A34
A35
A36
A37
A38
A39
A40
A41
A42
A43
A44
A45
A46
A47
A48
A49
A50
8
Row A
Signal
GND (FIXED)
NC
NC
GBE0_LINK100#
NC
NC
NC
GBE0_LINK#
GBE0_MDI1GBE0_MDI1+
GND (FIXED)
GBE0_MDI0GBE0_MDI0+
NC
SUS_S3#
SATA0_TX+
SATA0_TXSUS_S4#
SATA0_RX+
SATA0_RXGND (FIXED)
NC
NC
SUS_S5#
NC
NC
BATLOW#
ATA_ACT#
AC_SYNC
SC_RST#
GND (FIXED)
AC_BITCLK
AC_SDOUT
NC
THRMTRIP#
USB6USB6+
USB_6_7_OC#
USB4USB4+
GND (FIXED)
USB2USB2+
USB_2_3_OC#
USB0USB0+
VCC_RTC
EXCD0_PERST#
EXCD0CPPE#
LPC_SERIRQ
Row B
Pin
Signal
Pin
B1
GND (FIXED)
C1
B2
GBE0_ACT#
C2
B3
LPC_FRAME#
C3
B4
LPC_AD0
C4
B5
LPC_AD1
C5
B6
LPC_AD2
C6
B7
LPC_AD3
C7
B8
LPC_DRQ0#
C8
B9
LPC_DRQ1#
C9
B10
LPC_CLK
C10
B11
GND (FIXED)
C11
B12
PWRBTN#
C12
B13
SMB_CK
C13
B14
SMB_DAT
C14
B15
SMB_ALERT#
C15
B16
SATA1_TX+
C16
B17
SATA1_TXC17
B18
SUS-STAT#
C18
B19
SATA1_RX+
C19
B20
SATA1_RXC20
B21
GND (FIXED)
C21
B22
NC
C22
B23
NC
C23
B24
NC
C24
B25
NC
C25
B26
NC
C26
B27
WDT
C27
B28
AC_SDIN2
C28
B29
AC_SDIN1
C29
B30
AC_SDIN0
C30
B31
GND (FIXED)
C31
B32
SPKR
C32
B33 I2C_CK/GPIO38 C33
B34 I2C_DAT/GPIO39 C34
B35
THRM#
C35
B36
USB7C36
B37
USB7+
C37
B38
USB_4_5_OC#
C38
B39
USB5C39
B40
USB5+
C40
B41
GND (FIXED)
C41
B42
USB3C42
B43
USB3+
C43
B44
USB_0_1_OC#
C44
B45
USB1C45
B46
USB1+
C46
EXCD1_PERTST#
B47
C47
B48 EXCD1_CPPE# C48
B49
SYS_RESET#
C49
B50
CB_RESET#
C50
Row C
Signal
GND (FIXED)
IDE_D7
IDE_D6
IDE_D3
IDE_D15
IDE_D8
IDE_D9
IDE_D2
IDE_D13
IDE_D1
GND (FIXED)
IDE_D14
IDE_IORDY
IDE_IOR#
PCI_PME#
PCI_GNT2#
PCI_REQ2#
PCI_GNT1#
PcI_REQ1#
PCI_GNT0#
GND (FIXED)
PCI_REQ0#
PCI_RESET#
PCI_AD0
PCI_AD2
PCI_AD4
PCI_AD6
PCI_AD8
PCI_AD10
PCI_AD12
GND (FIXED)
PCI_AD14
PCI_C/BE1#
PCI_PERR#
PCI_LOCK#
PCI_DEVSEL#
PCI_IRDY#
PCI_C/BE2#
PCI_AD17
PCI_AD19
GND (FIXED)
PCI_AD21
PCI_AD23
PCI_C/BE3#
PCI_AD25
PCI_AD27
PCI_AD29
PCI_AD31
PCI_IRQA#
PCI_IRQB#
ET900 User’s Manual
Pin
D1
D2
D3
D4
D5
D6
D7
D8
D9
D10
D11
D12
D13
D14
D15
D16
D17
D18
D19
D20
D21
D22
D23
D24
D25
D26
D27
D28
D29
D30
D31
D32
D33
D34
D35
D36
D37
D38
D39
D40
D41
D42
D43
D44
D45
D46
D47
D48
D49
D50
Row D
Signal
GND (FIXED)
IDE_D5
IDE_D10
IDE_D11
IDE_D12
IDE_D4
IDE_D0
IDE_REQ
IDE_IOW#
IDE_ACK#
GND (FIXED)
IDE_IRQ
IDE_A0
IDE_A1
IDE_A2
IDE_CS1#
IDE_CS3#
IDE_RESET#
PCI_GNT3#
PCI_REQ3#
GND (FIXED)
PCI_AD1
PCI_AD3
PCI_AD5
PCI_AD7
PCI_C/BE0#
PCI_AD9
PCI_AD11
PCI_AD13
PCI_AD15
GND (FIXED)
PCI_PAR
PCI_SERR#
PCI_STOP#
PCI_TRDY#
PCI_FRAME#
PCI_AD16
PCI_AD18
PCI_AD20
PCI_AD22
GND (FIXED)
PCI_AD24
PCI_AD26
PCI_AD28
PCI_AD30
PCI_IRQC#
PCI_IRQD#
NC
NC
PCI_CLK
INTRODUCTION
Row A
Row B
Pin
Signal
Pin
Signal
Pin
A51
GND (FIXED)
B51
GND (FIXED)
C51
A52
PCIE_TX5+
B52
PCIE_RX5+
C52
A53
PCIE_TX5B53
PCIE_RX5C53
A54
GPI0
B54
GPO1
C54
A55
PCIE_TX4+
B55
PCIE_RX4+
C55
A56
PCIE_TX4B56
PCIE_RX4C56
A57
GND
B57
GPO2
C57
A58
PCIE_TX3+
B58
PCIE_RX3+
C58
A59
PCIE_TX3B59
PCIE_RX3C59
A60
GND (FIXED)
B60
GND (FIXED)
C60
A61
PCIE_TX2+
B61
PCIE_RX2+
C61
A62
PCIE_TX2B62
PCIE_RX2C62
A63
GPI1
B63
GPO3
C63
A64
PCIE_TX1+
B64
PCIE_RX1+
C64
A65
PCIE_TX1B65
PCIE_RX1C65
A66
GND
B66
WAKE0#
C66
A67
GPI2
B67
WAKE1#
C67
A68
PCIE_TX0+
B68
PCIE_RX0+
C68
A69
PCIE_TX0B69
PCIE_RX0C69
A70
GND (FIXED)
B70
GND (FIXED)
C70
A71
LVDS_A0+
B71
LVDS_B0+
C71
A72
LVDS_A0B72
LVDS_B0C72
A73
LVDS_A1+
B73
LVDS_B1+
C73
A74
LVDS_A1B74
LVDS_B1C74
A75
LVDS_A2+
B75
LVDS_B2+
C75
A76
LVDS_A2B76
LVDS_B2C76
A77 LVDS_VDD_EN B77
NC
C77
A78
NC
B78
NC
C78
A79
NC
B79 LVDS_BKLT_EN C79
A80
GND (FIXED)
B80
GND (FIXED)
C80
A81
LVDS_A_CK+
B81
LVDS_B_CK+
C81
A82
LVDS_A_CKB82
LVDS_B_CKC82
A83
LVDS_I2C_CK
B83 LVDS_BKLT_Ctrl C83
A84 LVDS_I2C_DAT B84
VCC_5V_SBY
C84
A85
GPI3
B85
VCC_5V_SBY
C85
A86
KBD_RST#
B86
VCC_5V_SBY
C86
A87 KBD_A20GATE B87
VCC_5V_SBY
C87
A88 PCIE0_CK_REF+ B88
RSVD
C88
A89 PCIE0_CK_REF- B89
VGA_RED
C89
A90
GND (FIXED)
B90
GND (FIXED)
C90
A91
RSVD
B91
VGA_GRN
C91
A92
RSVD
B92
VGA_BLU
C92
A93
GPO0
B93
VGA_HSYNC
C93
A94
RSVD
B94
VGA_VSYNC
C94
A95
RSVD
B95
VGA_I2C_CK
C95
A96
GND
B96 VGA_I2C_DATA C96
A97
VCC_12V
B97
TV_DAC_A
C97
A98
VCC_12V
B98
TV_DAC_B
C98
A99
VCC_12V
B99
TV_DAC_C
C99
A100
GND (FIXED)
B100
GND (FIXED)
C100
A101
VCC_12V
B101
VCC_12V
C101
A103
VCC_12V
B103
VCC_12V
C103
A103
VCC_12V
B103
VCC_12V
C103
A104
VCC_12V
B104
VCC_12V
C104
A105
VCC_12V
B105
VCC_12V
C105
A106
VCC_12V
B106
VCC_12V
C106
A107
VCC_12V
B107
VCC_12V
C107
A108
VCC_12V
B108
VCC_12V
C108
A109
VCC_12V
B109
VCC_12V
C109
A110
GND (FIXED)
B110
GND (FIXED)
C110
Row C
Signal
GND (FIXED)
PEG_RX0+
PEG_RX0NC
PEG_RX1+
PEG_RX1NC
PEG_RX2+
PEG_RX2GND (FIXED)
PEG_RX3+
PEG_RX3RSVD
RSVD
PEG_RX4+
PEG_RX4RSVD
PEG_RX5+
PEG_RX5GND (FIXED)
PEG_RX6+
PEG_RX6SDVO_DATA
PEG_RX7+
PEG_RX7GND
RSVD
PEG_RX8+
PEG_RX8GND (FIXED)
PEG_RX9+
PEG_RX9RSVD
GND
PEG_RX10+
PEG_RX10GND
PEG_RX11+
PEG_RX11GND (FIXED)
PEG_RX12+
PEG_RX12GND
PEG_RX13+
PEG_RX13GND
RSVD
PEG_RX14+
PEG_RX14GND (FIXED)
PEG_RX15+
PEG_RX15GND
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
VCC_12V
GND (FIXED)
ET900 User’s Manual
Row D
Pin
Signal
D51
GND (FIXED)
D52
PEG_TX0+
D53
PEG_TX0D54 PEG_LANE_RV#
D55
PEG_TX1+
D56
PEG_TX1D57
NC
D58
PEG_TX2+
D59
PEG_TX2D60
GND (FIXED)
D61
PEG_TX3+
D62
PEG_TX3D63
RSVD
D64
RSVD
D65
PEG_TX4+
D66
PEG_TX4D67
GND
D68
PEG_TX5+
D69
PEG_TX5D70
GND (FIXED)
D71
PEG_TX6+
D72
PEG_TX6D73
SDVO_CLK
D74
PEG_TX7+
D75
PEG_TX7D76
GND
D77
IDE_CBLID#
D78
PEG_TX8+
D79
PEG_TX8D80
GND (FIXED)
D81
PEG_TX9+
D82
PEG_TX9D83
RSVD
D84
GND
D85
PEG_TX10+
D86
PEG_TX10D87
GND
D88
PEG_TX11+
D89
PEG_TX11D90
GND (FIXED)
D91
PEG_TX12+
D92
PEG_TX12D93
GND
D94
PEG_TX13+
D95
PEG_TX13D96
GND
D97 PEG_ENABLE#
D98
PEG_TX14+
D99
PEG_TX14D100
GND (FIXED)
D101
PEG_TX15+
D103
PEG_TX15D103
GND
D104
VCC_12V
D105
VCC_12V
D106
VCC_12V
D107
VCC_12V
D108
VCC_12V
D109
VCC_12V
D110
GND (FIXED)
9
INTRODUCTION
This page is intentionally left blank.
10
ET900 User’s Manual
BIOS SETUP
BIOS Setup
This chapter describes the different settings available in the Award
BIOS that comes with the board. The topics covered in this chapter are
as follows:
BIOS Introduction ........................................................................ 12
BIOS Setup ................................................................................... 12
Standard CMOS Setup ................................................................. 14
Advanced BIOS Features ............................................................. 17
Advanced Chipset Features .......................................................... 20
Integrated Peripherals ................................................................... 23
Power Management Setup ............................................................ 27
PNP/PCI Configurations .............................................................. 30
PC Health Status ........................................................................... 31
Frequency/Voltage Control .......................................................... 32
Load Fail-Safe Defaults................................................................ 33
Load Optimized Defaults ............................................................. 33
Set Supervisor/User Password...................................................... 33
Save & Exit Setup ........................................................................ 33
Exit Without Saving ..................................................................... 33
ET900 User’s Manual
11
BIOS SETUP
BIOS Introduction
The Award BIOS (Basic Input/Output System) installed in your
computer system’s ROM supports Intel processors. The BIOS provides
critical low-level support for a standard device such as disk drives, serial
ports and parallel ports. It also adds virus and password protection as
well as special support for detailed fine-tuning of the chipset controlling
the entire system.
BIOS Setup
The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system stores
the Setup utility. When you turn on the computer, the Award BIOS is
immediately activated. Pressing the <Del> key immediately allows you
to enter the Setup utility. If you are a little bit late pressing the <Del>
key, POST (Power On Self Test) will continue with its test routines, thus
preventing you from invoking the Setup. If you still wish to enter Setup,
restart the system by pressing the ”Reset” button or simultaneously
pressing the <Ctrl>, <Alt> and <Delete> keys. You can also restart by
turning the system Off and back On again. The following message will
appear on the screen:
Press
<DEL>
to
Enter
Setup
In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.
When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.
12
ET900 User’s Manual
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Advanced BIOS Features
Advanced Chipset Features
Integrated Peripherals
Power Management Setup
PnP/PCI Configurations
PC Health Status
Frequency/Voltage Control
Load Fail-Safe Defaults
Load Optimized Defaults
Set Supervisor Password
Set User Password
Save & Exit Setup
Exit Without Saving
ESC : Quit
F10 : Save & Exit Setup
Ç È Æ Å : Select Item
Time, Date, Hard Disk Type…
The section below the setup items of the Main Menu displays the control
keys for this menu. At the bottom of the Main Menu just below the
control keys section, there is another section, which displays information
on the currently highlighted item in the list.
Note:
If the system cannot boot after making and saving system
changes with Setup, the Award BIOS supports an override to
the CMOS settings that resets your system to its default.
Warning: It is strongly recommended that you avoid making any
changes to the chipset defaults. These defaults have been
carefully chosen by both Award and your system
manufacturer to provide the absolute maximum performance
and reliability. Changing the defaults could cause the system
to become unstable and crash in some cases.
ET900 User’s Manual
13
BIOS SETUP
Standard CMOS Setup
“Standard CMOS Setup” choice allows you to record some basic
hardware configurations in your computer system and set the system
clock and error handling. If the board is already installed in a working
system, you will not need to select this option. You will need to run the
Standard CMOS option, however, if you change your system hardware
configurations, the onboard battery fails, or the configuration stored in
the CMOS memory was lost or damaged.
Phoenix - AwardBIOS CMOS Setup Utility
Standard CMOS Features
Date (mm:dd:yy)
Wed, Apr 28, 2004
Time (hh:mm:ss)
00 : 00 : 00
Menu Level >
Item Help
IDE Channel 0 Master
IDE Channel 0 Slave
IDE Channel 1 Master
IDE Channel 1 Slave
None
None
None
None
Change the day, month,
Year and century
Drive A
Drive B
1.44M, 3.5 in.
None
Video
Halt On
EGA/VGA
All Errors
Base Memory
Extended Memory
Total Memory
640K
129024K
130048K
At the bottom of the menu are the control keys for use on this menu. If
you need any help in each item field, you can press the <F1> key. It will
display the relevant information to help you. The memory display at the
lower right-hand side of the menu is read-only. It will adjust
automatically according to the memory changed. The following
describes each item of this menu.
Date
The date format is:
Day :
Month :
Date :
Year :
14
Sun to Sat
1 to 12
1 to 31
1999 to 2099
ET900 User’s Manual
BIOS SETUP
To set the date, highlight the “Date” field and use the PageUp/
PageDown or +/- keys to set the current time.
Time
The time format is:
Hour : 00 to 23
Minute : 00 to 59
Second : 00 to 59
To set the time, highlight the “Time” field and use the <PgUp>/ <PgDn>
or +/- keys to set the current time.
IDE Channel Master/Slave
The onboard PCI IDE connector provides Primary and Secondary
channels for connecting up to two IDE hard disks or other IDE devices.
Press <Enter> to configure the hard disk. The selections include Auto,
Manual, and None. Select ‘Manual’ to define the drive information
manually. You will be asked to enter the following items.
CYLS :
HEAD :
PRECOMP :
LANDING ZONE :
SECTOR :
Number of cylinders
Number of read/write heads
Write precompensation
Landing zone
Number of sectors
The Access Mode selections are as follows:
CHS (HD < 528MB)
LBA (HD > 528MB and supports
Logical Block Addressing)
Large (for MS-DOS only)
Auto
Remarks: The main board supports two serial ATA ports and are
represented in this setting as IDE Channel 0.
Drive A / Drive B
These fields identify the types of floppy disk drive A or drive B that has
been installed in the computer. The available specifications are:
360KB 1.2MB 720KB 1.44MB 2.88MB
5.25 in. 5.25 in. 3.5 in.
3.5 in.
3.5 in.
ET900 User’s Manual
15
BIOS SETUP
Video
This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA
For EGA, VGA, SEGA, SVGA
or PGA monitor adapters. (default)
CGA 40
Power up in 40 column mode.
CGA 80
Power up in 80 column mode.
MONO
For Hercules or MDA adapters.
Halt On
This field determines whether or not the system will halt if an error is
detected during power up.
No errors
The system boot will not be halted for any error
that may be detected.
All errors
Whenever the BIOS detects a non-fatal error,
the system will stop and you will be prompted.
All, But Keyboard
The system boot will not be halted for a
keyboard error; it will stop for all other errors
All, But Diskette
The system boot will not be halted for a disk
error; it will stop for all other errors.
All, But Disk/Key
The system boot will not be halted for a keyboard or disk error; it will stop for all others.
16
ET900 User’s Manual
BIOS SETUP
Advanced BIOS Features
This section allows you to configure and improve your system and
allows you to set up some system features according to your preference.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced BIOS Features
CPU Feature
Hard Disk Boot Priority
Virus Warning
CPU L1 and L2 Cache
Quick Power On Self Test
First Boot Device
Second Boot Device
Third Boot Device
Boot Other Device
Swap Floppy Drive
Boot Up Floppy Seek
Boot Up NumLock Status
Gate A20 Option
Typematic Rate Setting
Typematic Rate (Chars/Sec)
Typematic Delay (Msec)
Security Option
APIC Mode
MPS Version Control for OS
OS Select For DRAM>64MB
Report No FDD For WIN 95
Small Logo (EPA) Show
Press Enter
Press Enter
Disabled
Enabled
Enabled
Floppy
Hard Disk
CDROM
Enabled
Disabled
Disabled
On
Fast
Disabled
6
250
Setup
Enabled
1.4
Non-OS2
Yes
Enabled
ITEM HELP
Menu Level >
CPU Feature
Press Enter to configure the settings relevant to CPU Feature.
Hard Disk Boot Priority
With the field, there is the option to choose, aside from the hard disks connected,
“Bootable add-in Cards” which refers to other external devices.
Virus Warning
If this option is enabled, an alarm message will be displayed when trying to write
on the boot sector or on the partition table on the disk, which is typical of the
virus.
CPU L1 and L2 Cache
Cache memory is additional memory that is faster than conventional DRAM
(system memory). CPUs from 486-type on up contain internal cache memory,
and most, but not all, modern PCs have additional (external) cache memory.
When the CPU requests data, the system transfers the requested data from the
main DRAM into cache memory, for even faster access by the CPU. These allow
you to enable (speed up memory access) or disable the cache function.
ET900 User’s Manual
17
BIOS SETUP
Quick Power On Self Test
When enabled, this field speeds up the Power On Self Test (POST) after
the system is turned on. If it is set to Enabled, BIOS will skip some
items.
First/Second/Third Boot Device
These fields determine the drive that the system searches first for an
operating system. The options available include Floppy, LS120, Hard
Disk, CDROM, ZIP100, USB-Floppy, USB-ZIP, USB-CDROM, LAN
and Disable.
Boot Other Device
These fields allow the system to search for an OS from other devices
other than the ones selected in the First/Second/Third Boot Device.
Swap Floppy Drive
This item allows you to determine whether or not to enable Swap Floppy
Drive. When enabled, the BIOS swaps floppy drive assignments so that
Drive A becomes Drive B, and Drive B becomes Drive A. By default,
this field is set to Disabled.
Boot Up Floppy Seek
This feature controls whether the BIOS checks for a floppy drive while
booting up. If it cannot detect one (either due to improper configuration
or its absence), it will flash an error message.
Boot Up NumLock Status
This allows you to activate the NumLock function after you power up
the system.
Gate A20 Option
This field allows you to select how Gate A20 is worked. Gate A20 is a
device used to address memory above 1 MB.
Typematic Rate Setting
When disabled, continually holding down a key on your keyboard will
generate only one instance. When enabled, you can set the two typematic
controls listed next. By default, this field is set to Disabled.
Typematic Rate (Chars/Sec)
When the typematic rate is enabled, the system registers repeated
keystrokes speeds. Settings are from 6 to 30 characters per second.
18
ET900 User’s Manual
BIOS SETUP
Typematic Delay (Msec)
When the typematic rate is enabled, this item allows you to set the time
interval for displaying the first and second characters. By default, this
item is set to 250msec.
Security Option
This field allows you to limit access to the System and Setup. The default
value is Setup. When you select System, the system prompts for the User
Password every time you boot up. When you select Setup, the system
always boots up and prompts for the Supervisor Password only when the
Setup utility is called up.
APIC Mode
APIC stands for Advanced Programmable Interrupt Controller. The
default setting is Enabled.
MPS Version Control for OS
This option is specifies the MPS (Multiprocessor Specification) version
for your operating system. MPS version 1.4 added extended
configuration tables to improve support for multiple PCI bus
configurations and improve future expandability. The default setting is
1.4.
OS Select for DRAM > 64MB
This option allows the system to access greater than 64MB of DRAM
memory when used with OS/2 that depends on certain BIOS calls to
access memory. The default setting is Non-OS/2.
Report No FDD For WIN 95
If you are using Windows 95/98 without a floppy disk drive, select
Enabled to release IRQ6. This is required to pass Windows 95/98's SCT
test. You should also disable the Onboard FDC Controller in the
Integrated Peripherals screen when there's no floppy drive in the system.
If you set this feature to Disabled, the BIOS will not report the missing
floppy drive to Win95/98.
Small Logo (EPA) Show
The EPA logo appears at the right side of the monitor screen when the
system is boot up. The default setting is Enabled.
ET900 User’s Manual
19
BIOS SETUP
Advanced Chipset Features
This Setup menu controls the configuration of the chipset.
Phoenix - AwardBIOS CMOS Setup Utility
Advanced Chipset Features
DRAM Timing Selectable
CAS Latency Time
DRAM RAS# to CAS# Delay
DRAM RAS# Precharge
Precharge delay (tRAS)
System Memory Frequency
SLP_S4# Assertion Width
System BIOS Cacheable
Video BIOS Cacheable
Memory Hole at 15M-16M
PCI Express Root Port Func
By SPD
4
4
4
12
533MHZ
1 to 2 Sec
Enabled
Disabled
Disabled
Press Enter
** On-Chip VGA Setting **
PEG/On Chip VGA Control
On-Chip Frame Buffer Size
DVMT Mode
DVMT/FIXED memory Size
Boot Display
Panel Scaling
Panel Number
TV Standard
Video Connector
TV Format
Auto
8MB
DVMT
128MB
Auto
Auto
1024x768 18 bit SC
Off
Automatic
Auto
ITEM HELP
Menu Level >
DRAM Timing Selectable
This option refers to the method by which the DRAM timing is selected.
The default is By SPD.
CAS Latency Time
You can configure CAS latency time in HCLKs as 2 or 2.5 or 3. The
system board designer should set the values in this field, depending on
the DRAM installed. Do not change the values in this field unless you
change specifications of the installed DRAM or the installed CPU.
DRAM RAS# to CAS# Delay
This option allows you to insert a delay between the RAS (Row Address
Strobe) and CAS (Column Address Strobe) signals. This delay occurs
when the SDRAM is written to, read from or refreshed. Reducing the
delay improves the performance of the SDRAM.
20
ET900 User’s Manual
BIOS SETUP
DRAM RAS# Precharge
This option sets the number of cycles required for the RAS to
accumulate its charge before the SDRAM refreshes. The default setting
for the Active to Precharge Delay is 4.
Precharge Delay (tRAS)
The default setting for the Precharge Delay is 12.
System Memory Frequency
The default setting is 533MHz.
SLP_S4# Assertion Width
The default setting is 1 to 2 Sec.
System BIOS Cacheable
The setting of Enabled allows caching of the system BIOS ROM at
F000h-FFFFFh, resulting in better system performance. However, if
any program writes to this memory area, a system error may result.
Video BIOS Cacheable
The Setting Enabled allows caching of the video BIOS ROM at
C0000h-F7FFFh, resulting in better video performance. However, if
any program writes to this memory area, a system error may result.
Memory Hole At 15M-16M
In order to improve performance, certain space in memory can be
reserved for ISA cards. This memory must be mapped into the memory
space below 16 MB. The choices are Enabled and Disabled.
On-Chip VGA Setting
The fields under the On-Chip VGA Setting and their default settings are:
PEG/On Chip VGA Control: Auto
On-Chip Frame Buffer Size: 8MB
DVMT Mode: DVTM
DVMT/Fixed Memory Size: 128MB
Boot Display: Auto
Panel Scaling: Auto
Panel Number: 1024x768 18 bit SC
TV Standard: Off
Video Connector: Automatic
TV Format: Auto
ET900 User’s Manual
21
BIOS SETUP
Panel Scaling
The default setting is Auto. The options available include On and Off.
Panel Number
These fields allow you to select the LCD Panel type. The default values
for these ports are:
640x480
800x480
800x600
1024x768
1280x1024
1280x768
1400x1050
1600x1200
22
18bit
18bit
18bit
18bit
18bit
18bit
18bit
18bit
SC
SC
SC
SC
DC
SC
DC
DC
ET900 User’s Manual
BIOS SETUP
Integrated Peripherals
This section sets configurations for your hard disk and other integrated
peripherals. The first screen shows three main items for user to select.
Once an item selected, a submenu appears. Details follow.
Phoenix - AwardBIOS CMOS Setup Utility
Integrated Peripherals
Press Enter
Press Enter
Press Enter
OnChip IDE Device
Onboard Device
SuperIO Device
ITEM HELP
Menu Level >
Phoenix - AwardBIOS CMOS Setup Utility
OnChip IDE Device
IDE HDD Block Mode
On-chip Primary PCI IDE
IDE Primary Master PIO
IDE Primary Slave PIO
IDE Primary Master UDMA
IDE Primary Slave UDMA
On-Chip Secondary PCI IDE
IDE Secondary Master PIO
IDE Secondary Slave PIO
IDE Secondary Master UDMA
IDE Secondary Slave UDMA
Enabled
Enabled
Auto
Auto
Auto
Auto
Enabled
Auto
Auto
Auto
Auto
*** On-Chip Serial ATA Setting ***
On-Chip Serial ATA
PATA IDE Mode
SATA port
Auto
Secondary
P0, P2 is Primary
ITEM HELP
Menu Level >
Phoenix - AwardBIOS CMOS Setup Utility
Onboard Device
USB Controller
USB 2.0 Controller
USB Keyboard Support
AC97 Audio Select
Enabled
Enabled
Disabled
Auto
ET900 User’s Manual
ITEM HELP
Menu Level >
23
BIOS SETUP
Phoenix - AwardBIOS CMOS Setup Utility
SuperIO Device
POWER ON Function
KB Power ON Password
Hot Key power ON
Onboard FDC Controller
Onboard Serial Port 1
Onboard Serial Port 2
UART Mode Select
RxD , TxD Active
IR Transmission Delay
UR2 Duplex Mode
Use IR Pins
PWRON After PWR-Fail
BUTTON ONLY
Enter
Ctrl-F1
Enabled
3F8/IRQ4
2F8/IRQ3
Normal
Hi, Lo
Disabled
Half
IR-Rx2Tx2
Off
ITEM HELP
Menu Level >
IDE HDD Block Mode
This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.
On-chip Primary PCI IDE Enabled
This field, by default, is enabled
OnChip Primary/Secondary PCI IDE
The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select Enabled to activate each channel
separately.
IDE Primary/Secondary Master/Slave PIO
These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to or
from the disk drive, PIO (Programmed Input/Output) allows the BIOS to
communicate with the controller and CPU directly.
The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.
IDE Primary/Secondary Master/Slave UDMA
These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are Auto and
Disabled.
24
ET900 User’s Manual
BIOS SETUP
On-Chip Serial ATA Setting
The fields under the SATA setting includes On-Chip Serial ATA (Auto),
PATA IDE Mode (Secondary) and SATA Port (PO, P2 is Primary).
USB Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled.
USB 2.0 Controller
The options for this field are Enabled and Disabled. By default, this field
is set to Enabled. In order to use USB 2.0, necessary OS drivers must be
installed first. Please update your system to Windows 2000 SP4 or
Windows XP SP2.
USB Keyboard Support
The options for this field are Enabled and Disabled. By default, this field
is set to Disabled.
AC97 Audio Select
This field, by default, is set to Auto.
Power ON Function
This field is related to how the system is powered on – such as with the
use of conventional power button, keyboard or hot keys. The default is
BUTTON ONLY.
KB Power ON Password
This field allows users to set the password when keyboard power on is
the mode of the Power ON function.
Hot Key Power ON
This field sets certain keys, also known as hot keys, on the keyboard that
can be used as a ‘switch’ to power on the system.
Onboard FDC Controller
Select Enabled if your system has a floppy disk controller (FDC)
installed on the main board and you wish to use it. If you install an add-in
FDC or the system has no floppy drive, select Disabled in this field. This
option allows you to select the onboard FDD port.
ET900 User’s Manual
25
BIOS SETUP
Onboard Serial Port
These fields allow you to select the onboard serial ports and their
addresses. The default values for these ports are:
Serial Port 1
3F8/IRQ4
Serial Port 2
2F8/IRQ3
UART Mode Select
This field determines the UART 2 mode in your computer. The default
value is Normal. Other options include IrDA and ASKIR.
PWRON After PWR-Fail
This field sets the system power status whether on or off when power
returns to the system from a power failure situation.
26
ET900 User’s Manual
BIOS SETUP
Power Management Setup
Phoenix - AwardBIOS CMOS Setup Utility
Power Management Setup
ACPI Function
Enabled
ACPI Suspend
RUN VGABIOS if S3 Resume
Power Management
Video Off Method
Video Off In Suspend
Suspend Type
Modem Use IRQ
Suspend Mode
HDD Power Down
Soft-Off by PWR-BTTN
Wake-Up by PCI Card
Power On by Ring
Resume by Alarm
Date (of Month) Alarm
Time (hh:mm:ss) Alarm
S1(POS)
Auto
User Define
DPMS
Yes
Stop Grant
3
Disabled
Disabled
Instant-Off
Disabled
Disabled
Disabled
0
0:0:0
** Reload Global Timer Events **
Primary IDE 0
Primary IDE 1
Secondary IDE 0
Secondary IDE 1
FDD, COM, LPT Port
PCI PIRQ[A-D] #
Disabled
Disabled
Disabled
Disabled
Disabled
Disabled
ITEM HELP
Menu Level >
ACPI Function
Enable this function to support ACPI (Advance Configuration and
Power Interface).
ACPI Suspend
The default setting of the ACPI Suspend mode is S1(POS).
RUN VGABIOS if S3 Resume
The default setting of this field is Auto.
Power Management
This field allows you to select the type of power saving management
modes. There are four selections for Power Management.
Min. Power Saving
Minimum power management
Max. Power Saving
Maximum power management.
User Define
Each of the ranges is from 1 min. to
1hr. Except for HDD Power Down
which ranges from 1 min. to 15 min.
ET900 User’s Manual
27
BIOS SETUP
Video Off Method
This field defines the Video Off features. There are three options.
V/H SYNC + Blank
Default setting, blank the screen and turn
off vertical and horizontal scanning.
DPMS
Allows BIOS to control the video display.
Blank Screen
Writes blanks to the video buffer.
Video Off In Suspend
When enabled, the video is off in suspend mode. The default setting is
Yes.
Suspend Type
The default setting for the Suspend Type field is Stop Grant.
Modem Use IRQ
This field sets the IRQ used by the Modem. By default, the setting is 3.
Suspend Mode
When enabled, and after the set time of system inactivity, all devices
except the CPU will be shut off.
HDD Power Down
When enabled, and after the set time of system inactivity, the hard disk
drive will be powered down while all other devices remain active.
Soft-Off by PWRBTN
This field defines the power-off mode when using an ATX power
supply. The Instant Off mode allows powering off immediately upon
pressing the power button. In the Delay 4 Sec mode, the system powers
off when the power button is pressed for more than four seconds or
enters the suspend mode when pressed for less than 4 seconds.
Wake up by PCI Card
By default, this field is disabled.
Power On by Ring
This field enables or disables the power on of the system through the
modem connected to the serial port or LAN.
28
ET900 User’s Manual
BIOS SETUP
Resume by Alarm
This field enables or disables the resumption of the system operation.
When enabled, the user is allowed to set the Date and Time.
Reload Global Timer Events
The HDD, FDD, COM, LPT Ports, and PCI PIRQ are I/O events that can
prevent the system from entering a power saving mode or can awaken
the system from such a mode. When an I/O device wants to gain the
attention of the operating system, it signals this by causing an IRQ to
occur. When the operating system is ready to respond to the request, it
interrupts itself and performs the service.
ET900 User’s Manual
29
BIOS SETUP
PNP/PCI Configurations
This option configures the PCI bus system. All PCI bus systems on the
system use INT#, thus all installed PCI cards must be set to this value.
Phoenix - AwardBIOS CMOS Setup Utility
PnP/PCI Configurations
Init Display First
PCI Slot
Reset Configuration Data
Disabled
Resources Controlled By
IRQ Resources
Auto (ESCD)
Press Enter
PCI/VGA Palette Snoop
INT Pin 1 Assignment
INT Pin 2 Assignment
INT Pin 3 Assignment
INT Pin 4 Assignment
INT Pin 5 Assignment
INT Pin 6 Assignment
INT Pin 7 Assignment
INT Pin 8 Assignment
Disabled
Auto
Auto
Auto
Auto
Auto
Auto
Auto
Auto
**PCI Express relative items**
Maximum Payload Size
4096
ITEM HELP
Menu Level
Select Yes if you are
using a Plug and Play
capable operating
system Select No if
you need the BIOS to
configure non-boot
devices
Init Display First
The default setting is PCI Card.
Reset Configuration Data
This field allows you to determine whether to reset the configuration
data or not. The default value is Disabled.
Resources Controlled by
This PnP BIOS can configure all of the boot and compatible devices
with the use of a PnP operating system such as Windows 95.
PCI/VGA Palette Snoop
Some non-standard VGA display cards may not show colors properly.
This field allows you to set whether or not MPEG ISA/VESA VGA
cards can work with PCI/VGA. When this field is enabled, a PCI/VGA
can work with an MPEG ISA/VESA VGA card. When this field is
disabled, a PCI/VGA cannot work with an MPEG ISA/VESA card.
Maximum Payload Size
The default setting of the PCI Express Maximum Payload Size is 4096.
30
ET900 User’s Manual
BIOS SETUP
PC Health Status
This section shows the parameters in determining the PC Health Status.
These parameters include temperatures, fan speeds and voltages.
Phoenix - AwardBIOS CMOS Setup Utility
PC Health Status
CPU Warning Temperature
Current System Temp
Current CPU Temp
Vcore(V)
Vcc3
Shutdown Temperature
System FAN Speed
CPU FAN Speed
Disabled
45°C/113°F
45°C/113°F
1.02 V
3.3V
Disabled
5400 RPM
5400 RPM
ITEM HELP
Menu Level >
CPU Warning Temperature
This field allows the user to set the temperature so that when the
temperature is reached, the system sounds a warning. This function can
help prevent damage to the system that is caused by overheating.
Temperatures/Voltages
These fields are the parameters of the hardware monitoring function
feature of the main board. The values are read-only values as monitored
by the system and show the PC health status.
Shutdown Temperature
This field allows the user to set the temperature by which the system
automatically shuts down once the threshold temperature is reached.
This function can help prevent damage to the system that is caused by
overheating.
ET900 User’s Manual
31
BIOS SETUP
Frequency/Voltage Control
This section shows the user how to configure the processor frequency.
Phoenix - AwardBIOS CMOS Setup Utility
Frequency/Voltage Control
Auto Detect PCI Clk
Disabled
Spread Spectrum Modulated
Disabled
ITEM HELP
Menu Level >
Auto Detect PCI Clk
This field enables or disables the auto detection of the PCI clock.
Spread Spectrum Modulated
This field sets the value of the spread spectrum. The default setting is
Disabled. This field is for CE testing use only.
32
ET900 User’s Manual
BIOS SETUP
Load Fail-Safe Defaults
This option allows you to load the troubleshooting default values
permanently stored in the BIOS ROM. These default settings are
non-optimal and disable all high-performance features.
Load Optimized Defaults
This option allows you to load the default values to your system
configuration. These default settings are optimal and enable all high
performance features.
Set Supervisor Password
These two options set the system password. Supervisor Password sets a
password that will be used to protect the system and Setup utility. User
Password sets a password that will be used exclusively on the system. To
specify a password, highlight the type you want and press <Enter>. The
Enter Password: message prompts on the screen. Type the password, up
to eight characters in length, and press <Enter>. The system confirms
your password by asking you to type it again. After setting a password,
the screen automatically returns to the main screen.
To disable a password, just press the <Enter> key when you are
prompted to enter the password. A message will confirm the password to
be disabled. Once the password is disabled, the system will boot and you
can enter Setup freely.
Save & Exit Setup
This option allows you to determine whether or not to accept the
modifications. If you type “Y”, you will quit the setup utility and save all
changes into the CMOS memory. If you type “N”, you will return to
Setup utility.
Exit Without Saving
Select this option to exit the Setup utility without saving the changes you
have made in this session. Typing “Y” will quit the Setup utility without
saving the modifications. Typing “N” will return you to Setup utility.
ET900 User’s Manual
33
BIOS SETUP
This page is intentionally left blank.
34
ET900 User’s Manual
DRIVERS INSTALLATION
Drivers Installation
This section describes the installation procedures for software and
drivers under the Windows 98SE, Windows ME, Windows 2000 and
Windows XP. The software and drivers are included with the main board
If you find the items missing, please contact the vendor where you made
the purchase. The contents of this section include the following:
Intel Chipset Software Installation Utility......................... 36
VGA Drivers Installation .................................................. 38
AC97 Codec Audio Driver Installation (IP400 carrier board
only) .................................................................................. 40
Intel PRO LAN Drivers Installation .................................. 42
Marvell LAN Drivers Installation (IP400 carrier board only)
........................................................................................... 43
IMPORTANT NOTE:
After installing your Windows operating system (Windows
98SE/ME/2000/XP), you must install first the Intel Chipset Software
Installation Utility before proceeding with the drivers installation.
ET900 User’s Manual
35
DRIVERS INSTALLATION
Intel Chipset Software Installation Utility
The Intel Chipset Drivers should be installed first before the software
drivers to enable Plug & Play INF support for Intel chipset components.
Follow the instructions below to complete the installation under
Windows 2000/XP.
1. Insert the CD that comes with the board. Click Intel Chipsets and then
Intel(R) I945GM Chipset Drivers.
2. Click Intel(R) Chipset Software Installation Utility.
36
ET900 User’s Manual
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. Click Yes to accept the software license agreement and proceed with
the installation process.
5. On Readme Information screen, click Next to continue the
installation.
6. The Setup process is now complete. Click Finish to restart the
computer and for changes to take effect. When the computer has
restarted, the system will be able to find some devices. Restart your
computer when prompted.
ET900 User’s Manual
37
DRIVERS INSTALLATION
VGA Drivers Installation
To install the VGA drivers, follow the steps below to proceed with the
installation.
1. Insert the CD that comes with the board. Click Intel Chipsets and then
Intel(R) I945GM Chipset Drivers.
2. Click Intel(R) I945GM Chipset Family Graphics Driver.
38
ET900 User’s Manual
DRIVERS INSTALLATION
3. When the Welcome screen appears, click Next to continue.
4. When the setup is complete, restart the computer as prompted and for
changes to take effect.
ET900 User’s Manual
39
DRIVERS INSTALLATION
AC97 Codec Audio Driver Installation (IP400
carrier board only)
Follow the steps below to install the Realtek AC97 Codec Audio
Drivers.
1. Insert the CD that comes with the board. Click Intel Chipsets and then
Intel(R) I945GM Chipset Drivers.
2. Click Realtek Codec Audio Audio Driver.
3. When the screen below appears, click Yes to continue with the
installation.
40
ET900 User’s Manual
DRIVERS INSTALLATION
4. Click Finish to restart the computer and for changes to take effect. .
ET900 User’s Manual
41
DRIVERS INSTALLATION
Intel PRO LAN Drivers Installation
Follow the steps below to complete the installation of the Intel PRO
LAN drivers.
1. Insert the CD that comes with the board. Click Intel Chipsets and then
Intel(R) I945GM Chipset Drivers. Then, click Intel(R) PRO LAN
Network Drivers.
2. Click Install Base Software to continue.
3. When prompted, please to restart the computer for new settings to take
effect.
42
ET900 User’s Manual
DRIVERS INSTALLATION
Marvell LAN Drivers Installation (IP400 carrier
board only)
Follow the steps below to complete the installation of the Intel PRO
LAN drivers.
1. Insert the CD that comes with the board. Click LAN Card and then
Marvell LAN Controller Driver.
2. When the Welcome screeen appears, click Next to continue.
3. Click Next to agree with the license agreement.
ET900 User’s Manual
43
DRIVERS INSTALLATION
4. When the Readme Information appears, click Next to continue
5. When the Ready to Install the Program appears, click Install to
continue.
6. After the installation is complete, click Finish.
7. To use the wake up function with PCIe LAN, go to the Device
Manager under Windows and select LAN controller. The window for
Generic Marvell Yukon Chipset based Ethernet Controller Properties
will appear. Click Advanced and select Wake From Shutdown. In the
Value field on the right, select On.
8. Then, also in the Advanced section, click on Wake Up Capabilities. In
the Value field on the right, select Magic Packet, then click OK.
44
ET900 User’s Manual
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement