Block Up Converter Systems 6700/6900 series

Add to my manuals
149 Pages

advertisement

Block Up Converter Systems 6700/6900 series | Manualzz
Block Up Converter Systems
6700/6900 series
S AT E L L I T E CO M M U N I C AT I O N S
USER
GUIDE
No part of this guide may be reproduced, transcribed or
translated into any language or transmitted in any form
whatsoever without the prior written consent of Codan
Limited.
© Copyright 2006 Codan Limited.
Codan part number 15-44027-EN Issue 1, October 2006
Table of contents
CODAN
Introduction
1
Overview
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
BUC system configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
BUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Transmit frequency bands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Frequency conversion plans . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Power supply options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
LNB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Redundancy systems. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
The redundancy controller . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
How the redundancy controller works . . . . . . . . . . . . . . . . . . . . . . . . . 20
RF waveguide switches. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
The Remote Controller 6570 and Hand-held Controller 6560 . . . . . . . . . . 26
2
Installation
Unpacking the equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Installing the BUC equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Cable recommendations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Cable lengths. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
IF levels. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Serial interfaces. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
RS232 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
RS422/485 interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
FSK interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Connecting the serial interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Permanent interface connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Temporary interface connection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Monitor and control interface of the BUC . . . . . . . . . . . . . . . . . . . . . . . . . 40
Installing the redundancy system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Block Up Converter Systems 6700/6900 series User Guide
i
Table of contents
Mounting the redundancy controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Installing separate transmit and receive RF waveguide switches . . . . . 42
Installing the combined RF waveguide/coaxial switch (C-Band
transmit/receive systems only). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Connecting the power cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Connecting the control cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Connecting the IF from the redundancy controller to the BUCs . . . . . . 48
Connecting the IF cables between an L-Band IF modem (or other
equipment) and the redundancy controller. . . . . . . . . . . . . . . . . . . . . . . 48
Connecting the IF from the LNBs to the redundancy controller . . . . . . 49
Grounding the installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Serial interfaces of the BUCs from the redundancy controller . . . . . . . . . . 50
Accessing the Auxiliary I/O interface on the redundancy controller . . . . . 51
Setting up the redundancy switching equipment . . . . . . . . . . . . . . . . . . . . . 53
3
Setting up and operating the BUC system
Switching on the BUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 58
LED indicators. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Serial interface monitor and control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Serial interface commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Switching the redundancy system on and off . . . . . . . . . . . . . . . . . . . . . . . 76
Checking the operation of the LED indicators and controls . . . . . . . . . . . . 76
Switching between streams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76
Controlling the redundancy system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
4
Maintenance and fault finding
Precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Connections to power supplies . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Servicing requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
RF waveguide switches . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Fuses and overcurrent protection in the Redundancy Controller
6586 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
If technical assistance is required... . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Finding faults in the BUC system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
ii
Block Up Converter Systems 6700/6900 series User Guide
Table of contents
Using the BUC fault diagnosis charts . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Test procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Finding faults in the redundancy switching equipment . . . . . . . . . . . . . . 100
Replacing fuses in the redundancy controller . . . . . . . . . . . . . . . . . . . 102
Resolving inconsistent stream selections . . . . . . . . . . . . . . . . . . . . . . 103
Finding faults in an RF waveguide switch . . . . . . . . . . . . . . . . . . . . . 103
Finding faults in the redundancy controller . . . . . . . . . . . . . . . . . . . . 107
Disconnecting a faulty BUC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Reverting to a single-BUC earth station . . . . . . . . . . . . . . . . . . . . . . . 108
Finding faults in the remote controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
Appendix A—BUC model and redundancy system
numbers
Appendix B—Example outputs for the View
commands
Appendix C—Compliance
Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 120
European R&TTE Directive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
Electromagnetic compatibility and safety notices . . . . . . . . . . . . . . . . . . 123
Appendix D—Definitions
Standards and icons . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Acronyms and abbreviations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 129
Units . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 131
Unit multipliers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
About this issue. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Index
Block Up Converter Systems 6700/6900 series User Guide
iii
Table of contents
This page has been left blank intentionally.
iv
Block Up Converter Systems 6700/6900 series User Guide
List of figures
CODAN
Figure 1:
BUC with L-Band modem and LNB . . . . . . . . . . . . . . . . 5
Figure 2:
BUC with L-Band modem, external in-line PSU,
and LNB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 3:
C-Band frequency conversion plan at an LO
frequency of 7300 MHz . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 4:
C-Band frequency conversion plan at an LO
frequency of 7375 MHz . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 5:
C-Band frequency conversion plan at an LO
frequency of 7600 MHz . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 6:
C-Band frequency conversion plan at an LO
frequency of 7675 MHz . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 7:
Ku-Band frequency conversion plan for BUCs
that cover the Standard frequency band . . . . . . . . . . . . . 12
Figure 8:
Ku-Band frequency conversion plan for BUCs
that cover the Extended frequency band . . . . . . . . . . . . 13
Figure 9:
Control panel on the redundancy controller . . . . . . . . . . 18
Figure 10:
Connector panel on the redundancy controller. . . . . . . . 19
Figure 11:
IF levels required for short cables . . . . . . . . . . . . . . . . . 35
Figure 12:
IF levels required for long cables . . . . . . . . . . . . . . . . . . 36
Figure 13:
Monitor and control interface of the BUC . . . . . . . . . . . 41
Figure 14:
Auxiliary I/O interface of the redundancy controller . . . 52
Figure 15:
Main BUC fault diagnosis chart . . . . . . . . . . . . . . . . . . . 86
Figure 16:
BUC fault diagnosis chart 1 . . . . . . . . . . . . . . . . . . . . . . 87
Figure 17:
BUC fault diagnosis chart 2 . . . . . . . . . . . . . . . . . . . . . . 88
Figure 18:
BUC fault diagnosis chart 3 . . . . . . . . . . . . . . . . . . . . . . 89
Figure 19:
BUC fault diagnosis chart 4 . . . . . . . . . . . . . . . . . . . . . . 90
Figure 20:
BUC fault diagnosis chart 5 . . . . . . . . . . . . . . . . . . . . . . 91
Figure 21:
BUC fault diagnosis chart 6 . . . . . . . . . . . . . . . . . . . . . . 92
Figure 22:
BUC fault diagnosis chart 7 . . . . . . . . . . . . . . . . . . . . . . 93
Figure 23:
BUC fan fault diagnosis chart 1 . . . . . . . . . . . . . . . . . . . 94
Figure 24:
BUC fan fault diagnosis chart 2 . . . . . . . . . . . . . . . . . . . 95
Figure 25:
LNB fault diagnosis chart. . . . . . . . . . . . . . . . . . . . . . . . 96
Block Up Converter Systems 6700/6900 series User Guide
v
List of figures
vi
Figure 26:
RF waveguide switch fault diagnosis chart . . . . . . . . . .104
Figure 27:
Remote controller supply fault diagnosis chart . . . . . . .110
Figure 28:
Segments of the BUC model number . . . . . . . . . . . . . .111
Figure 29:
Segments of the redundancy system number. . . . . . . . .113
Block Up Converter Systems 6700/6900 series User Guide
List of tables
CODAN
Table 1:
Transmit frequency bands for C-Band and
Ku-Band BUCs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Table 2:
Frequency ranges for C-Band BUCs (Standard) . . . . . . . 8
Table 3:
Frequency ranges for C-Band BUCs (Extended) . . . . . . . 9
Table 4:
Frequency ranges for Ku-Band BUCs (Standard) . . . . . 11
Table 5:
Frequency ranges for Ku-Band BUCs (Extended) . . . . . 12
Table 6:
Power supply options for BUCs . . . . . . . . . . . . . . . . . . . 13
Table 7:
Frequency band options for the Ku-Band LNB . . . . . . . 15
Table 8:
Pinouts of the AC INPUT connector
(Amphenol T 3110 000) . . . . . . . . . . . . . . . . . . . . . . . . . 31
Table 9:
Recommendations for IF coaxial cables. . . . . . . . . . . . . 32
Table 10:
Cable lengths resulting in a 20 dB loss . . . . . . . . . . . . . 33
Table 11:
LED indicators on the BUC and their states . . . . . . . . . 59
Table 12:
LED indicators on the control panel of the
redundancy controller . . . . . . . . . . . . . . . . . . . . . . . . . . . 60
Table 13:
Help commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Table 14:
Set commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
Table 15:
Output commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Table 16:
View commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
Table 17:
Reset commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Table 18:
Fuses in the redundancy controller. . . . . . . . . . . . . . . . . 83
Table 19:
Test A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 20:
Test B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Table 21:
Test C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Table 22:
Test D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Table 23:
Test E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 98
Table 24:
Test F . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Table 25:
Resistance of coils when the RF waveguide
switch is in positions 1 and 2 . . . . . . . . . . . . . . . . . . . . 105
Table 26:
Tell-back contacts for switch positions 1 and 2 . . . . . . 108
Table 27:
Definition of the BUC model number . . . . . . . . . . . . . 111
Table 28:
Definition of the redundancy system number . . . . . . . 113
Block Up Converter Systems 6700/6900 series User Guide
vii
List of tables
viii
Table 29:
Electrical safety symbols . . . . . . . . . . . . . . . . . . . . . . . .125
Table 30:
Earth symbols . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Table 31:
Warning labels . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .126
Block Up Converter Systems 6700/6900 series User Guide
Introduction
CODAN
This user guide is for installation technicians and operators of
the Block Up Converter 6700/6900 series.
This guide contains the following sections:
Section 1
Overview—general description of the BUC
Section 2
Installation—installation instructions specific to
the BUC and redundancy systems
Section 3
Setting up and operating the BUC system—
setup and operating procedures, and serial
interface commands
Section 4
Maintenance and fault finding—description of
how to maintain and fault find a BUC and a
redundancy system
Appendix A BUC model and redundancy system numbers—
explains how to interpret the model number of
your BUC and redundancy system
Appendix B Example outputs for the View commands—
summary of the commands described on
page 57, Setting up and operating the BUC
system
Appendix C Compliance—compliance information and
safety notices
Appendix D Definitions—explains the terms and
abbreviations used in this guide
An index can be found at the end of the guide.
Block Up Converter Systems 6700/6900 series User Guide
1
Introduction
This page has been left blank intentionally.
2
Block Up Converter Systems 6700/6900 series User Guide
1
Overview
CODAN
This section contains the following topics:
Introduction (4)
BUC system configuration (5)
BUC (7)
LNB (15)
Redundancy systems (16)
The Remote Controller 6570 and Hand-held
Controller 6560 (26)
Block Up Converter Systems 6700/6900 series User Guide
3
Overview
Introduction
The Codan Block Up Converter 6700/6900 series is a highperformance BUC for use in a satellite earth station.
The Block Up Converter 6700/6900 series comprises:
•
a BUC
•
an LNB
•
a TRF
•
accessories
The BUC is designed to be mounted on a wide range of earth
station antennas. The LNB and TRF are designed to be directmounted (that is, mounted on the antenna feed support
structure). While some BUCs may be direct-mounted to the
feed, others may be boom-mounted or pedestal-mounted.
The BUC converts transmit L-Band IF signals from the
modem to the required RF band. The LNB converts received
RF signals to IF signals in the L-Band frequency range to
drive the modem receive IF input.
The modem generally supplies the BUC and the LNB with
10 MHz reference signals, and the LNB with the required DC
power. Certain BUCs require external sources of either AC or
DC supply. Certain BUCS and LNBs have internal reference
sources and do not require an external 10 MHz reference
signal.
NOTE
If your modem cannot supply 10 MHz reference
signals to the LNB and BUC, and DC power to
the LNB (and BUC if this is needed), contact
your Codan representative for information on
accessories and options that may be available.
The TRF is a waveguide filter that ensures transmit signals do
not enter and overload the LNB.
C-Band BUCs are supplied with a waveguide or N-type
output. Ku-Band BUCs are supplied with a waveguide output
only.
4
Block Up Converter Systems 6700/6900 series User Guide
Overview
BUC system configuration
The BUC may be used in the following configurations:
Configuration...
See...
BUC with L-Band modem and LNB
Figure 1 on page 5
BUC with L-Band modem, external
in-line PSU, and LNB
Figure 2 on page 6
Figure 1:
BUC with L-Band modem and LNB
External AC power
connector or
+48 V DC power
L-Band Tx IF,
+24/48 V DC power
(DC-powered BUC only),
10 MHz Ref*,
FSK M&C
(optional)
Tx to
antenna
BUC
Monitor &
Control
RS232/422/485
Monitor & Control
(optional)
Data
L-Band
Modem
AC mains
L-Band Rx IF,
+15 V DC power (nominal),
10 MHz Ref*
LNB
TRF
Rx from
antenna
* Certain BUC and LNB versions have internal references
and do not require an external 10 MHz reference
Block Up Converter Systems 6700/6900 series User Guide
5
Overview
Figure 2: BUC with L-Band modem, external in-line
PSU, and LNB
L-Band Tx IF,
48 V DC,
10 MHz Ref*,
FSK M&C
(optional)
AC mains
Monitor &
Control
Data
External
in-line
BUC PSU
Tx to
antenna
BUC
RS232/422/485
Monitor & Control
(optional)
L-Band Tx IF,
10 MHz Ref,
FSK M&C
(optional)
L-Band
Modem
AC mains
L-Band Rx IF,
+15 V DC power (nominal),
10 MHz Ref*
LNB
TRF
Rx from
antenna
* Certain BUC and LNB versions have internal references
and do not require an external 10 MHz reference
6
Block Up Converter Systems 6700/6900 series User Guide
Overview
BUC
Transmit frequency bands
Table 1: Transmit frequency bands for C-Band and
Ku-Band BUCs
BUC
Frequency band
Transmit frequency
band
(MHz)
C-Band
Standard
5 850 to 6425
Extended
5 850 to 6725
Standard
14000 to 14500
Extended
13750 to 14500
Ku-Band
Frequency conversion plans
All 6700/6900 series BUCs are frequency inverting, that is,
the higher the RF frequency required, the lower the modem
IF frequency must be.
To calculate the modem IF frequency (fIF) for a given
RF frequency, subtract the RF frequency (fRF) from the LO
frequency (fLO).
fIF = fLO – fRF
Block Up Converter Systems 6700/6900 series User Guide
7
Overview
Example 1:
The LO frequency of your C-Band BUC is set to 7300 MHz
(see Table 3 on page 9). If you need an RF frequency of
5975 MHz, then you must set the modem IF frequency to:
fIF = 7300 – 5975
= 1325 MHz
Example 2:
The LO frequency of your Ku-Band BUC is 15450 MHz (see
Table 4 on page 11). If you need an RF frequency of
14500 MHz, then you must set the modem IF frequency to:
fIF = 15450 – 14500
= 950 MHz
C-Band
Figure 3 to Figure 6 show the frequency conversion plan for
each LO frequency of the C-Band BUCs.
Table 2: Frequency ranges for C-Band BUCs
(Standard)
8
LO frequency
(MHz)
Tuning range of
L-Band
(MHz)
Output
frequency
(MHz)
fLO
fIF
fRF
7300
950–1450
5850–6350
Figure 3 on page 9
7375
950–1525
5850–6425
Figure 4 on page 10
See...
Block Up Converter Systems 6700/6900 series User Guide
Overview
Table 3: Frequency ranges for C-Band BUCs
(Extended)
LO frequency
(MHz)
Tuning range of
L-Band
(MHz)
Output
frequency
(MHz)
fLO
fIF
fRF
7300
950–1450
5850–6350
Figure 3 on page 9
7375
950–1525
5850–6425
Figure 4 on page 10
7600
950–1750
5850–6650
Figure 5 on page 10
7675
950–1750
5925–6725
Figure 6 on page 11
See...
Figure 3: C-Band frequency conversion plan at an LO
frequency of 7300 MHz
1 450 MHz
950 MHz
6 350 MHz
IF input
Block Up Converter Systems 6700/6900 series User Guide
RF output
5 850 MHz
9
Overview
Figure 4: C-Band frequency conversion plan at an LO
frequency of 7375 MHz
1 525 MHz
950 MHz
6 425 MHz
IF input
RF output
5 850 MHz
Figure 5: C-Band frequency conversion plan at an LO
frequency of 7600 MHz
1 750 MHz
950 MHz
10
6 650 MHz
IF input
RF output
5 850 MHz
Block Up Converter Systems 6700/6900 series User Guide
Overview
Figure 6: C-Band frequency conversion plan at an LO
frequency of 7675 MHz
1 750 MHz
950 MHz
6 725 MHz
5 925 MHz
RF output
IF input
Ku-Band
Figure 7 and Figure 8 show the frequency conversion plans
for each LO frequency of the Ku-Band BUCs.
Table 4: Frequency ranges for Ku-Band BUCs
(Standard)
LO frequency
(MHz)
Tuning range of
L-Band
(MHz)
Output
frequency
(MHz)
fLO
fIF
fRF
15450
950–1450
14000–14500
Block Up Converter Systems 6700/6900 series User Guide
See...
Figure 7 on page 12
11
Overview
Table 5: Frequency ranges for Ku-Band BUCs
(Extended)
LO frequency
(MHz)
Tuning range of
L-Band
(MHz)
Output
frequency
(MHz)
fLO
fIF
fRF
15450
950–1450
14000–14500
Figure 7 on page 12
15450
950–1700
13750–14500
Figure 8 on page 13
See...
Figure 7: Ku-Band frequency conversion plan for
BUCs that cover the Standard frequency band
1 450 MHz
950 MHz
12
14 500 MHz
IF input
RF output
14 000 MHz
Block Up Converter Systems 6700/6900 series User Guide
Overview
Figure 8: Ku-Band frequency conversion plan for
BUCs that cover the Extended frequency band
1 700 MHz
14 500 MHz
1 450 MHz
14 000 MHz
950 MHz
IF input
13 750 MHz
RF output
Power supply options
The power supply option for your BUC is indicated in the
model number on the serial number label. For information on
how to interpret the model number see page 111, BUC model
and redundancy system numbers.
Some BUCs are powered by 48 V DC or 24 V DC. Other
BUCs are powered via an AC mains input.
Table 6:
Power supply options for BUCs
Input
Power supply option
Feed to BUC
DC
24 V/48 V
via IF cable or separate
cable and connector
AC
94–275 V AC
via separate cable and
connector
Block Up Converter Systems 6700/6900 series User Guide
13
Overview
14
NOTE
BUCs that are AC-powered, also draw current
from the DC power input on the IF input cable
for remote alarm indication purposes only.
NOTE
Certain BUCs with external DC power
connectors may also have auto-sensing circuits,
and can be powered from either the external
connector or via the IF INPUT connector. If
both connectors are powered, the external
connector is automatically selected.
Block Up Converter Systems 6700/6900 series User Guide
Overview
LNB
The frequency band that is down converted by the LNB is
indicated on the model label of the LNB.
C-Band
The C-Band LNB is supplied for operation on the frequency
band 3400 to 4200 MHz. It has an LO frequency of
5150 MHz.
NOTE
The C-Band LNB is frequency inverting.
Ku-Band
The Ku-Band LNB may be supplied for operation in one of
three frequency band options listed in Table 7.
Table 7:
Frequency band options for the Ku-Band LNB
Band option Receive frequency
(MHz)
LO frequency
(MHz)
L-Band output
frequency
(MHz)
1
10950–11700
10000
950–1700
2
11700–12200
10750
950–1450
3
12250–12750
11300
950–1450
Block Up Converter Systems 6700/6900 series User Guide
15
Overview
Redundancy systems
The Codan Redundancy Controller 6586 is used to control two
BUCs and two LNBs (when used) in a redundancy system.
When a detectable fault occurs in the on-line BUC, and the
off-line BUC is serviceable, the redundancy controller
switches over the two BUCs. The interruption to traffic is
typically less than one second. Transmit/receive systems also
include two LNBs, which are switched in parallel with the
BUCS. In such systems, simultaneous switching of both BUC
and LNB occurs when a fault is detected in either the on-line
BUC or the on-line LNB. This is known as stream-switching.
A typical BUC-LNB system comprises:
•
a BUC
•
an LNB (in transmit/receive systems only)
•
a TRF (optional)
•
appropriate connecting cables
A typical redundancy system comprises:
•
two BUCs
•
two LNBs (in transmit/receive systems only)
•
an Redundancy Controller 6586
•
one or two RF waveguide switches or a combined RF
waveguide/coaxial switch
•
a Remote Controller 6570 (optional)
For information on the remote controller see the Hand-held
and Remote Controller 6560/6570 User Guide.
16
Block Up Converter Systems 6700/6900 series User Guide
Overview
Redundancy system control
You can control and monitor the redundancy switching
equipment:
•
locally, using a Hand-held Controller 6560 connected to
the BUC 1 Serial/BUC 2 Serial connectors on the
redundancy controller
•
remotely, using the optional Remote Controller 6570
connected to the Auxiliary I/O connector on the
redundancy controller
The redundancy controller
The redundancy controller is the main component of the
redundancy system. It controls the switching between the
on-line and off-line BUC and LNB. The redundancy controller
is normally installed on the antenna pedestal near the two
BUC systems. The redundancy controller is powered from the
AC mains supply.
The redundancy controller performs the following functions:
•
monitors the Stream 1 and Stream 2 equipment for faults
•
monitors the RF waveguide switches for switch faults
•
controls the RF waveguide switch positions
•
directs the IF paths via high frequency relays and splitter
networks
•
supplies power to the BUCs, LNBs (when used), and
optional Remote Controller 6570
The redundancy controller communicates with the BUCs via
relay contacts. The serial interfaces of the BUCs are kept
available for separate use. DC supply connections and isolated
contact closures are available on the Auxiliary I/O connector
of the redundancy controller.
The control panel inside the redundancy controller is shown in
Figure 9.
Block Up Converter Systems 6700/6900 series User Guide
17
Overview
Figure 9:
Control panel on the redundancy controller
BUC 1
Redundancy
Controller
LNB 1*
Tx IF
BUC
Switch
Status
BUC 2
Rx IF
LNB
Switch*
LNB 2*
Remote
Voltage
Selection Controller
BUC 1
BUC 2
LNB 1*
LNB 2*
Fuse status LEDs
* Not used in transmit-only systems
LED indicators
The control panel of the redundancy controller has groups of
LEDs that indicate the status of the redundancy system and its
fuses. The colours and functions of these LEDs are described
in Table 12 on page 60.
18
Block Up Converter Systems 6700/6900 series User Guide
Overview
Switches
The control panel of the redundancy controller has one switch.
The function of this switch is to select the AC input voltage
(115 or 230 V AC).
Connectors
The connector panel is located at the bottom of the
redundancy controller.
Figure 10: Connector panel on the redundancy
controller
BUC Switch Control
BUC 1 Serial
BUC 1 Control
AC Power Input
LNB Switch Control
BUC 2 Serial
BUC 2 Control
Auxiliary I/O
Tx IF Output 1
Tx IF Input
Tx IF Output 2
Rx IF Input 1
Block Up Converter Systems 6700/6900 series User Guide
Rx IF Output
Rx IF Input 2
19
Overview
How the redundancy controller works
When you power up the system, the redundancy controller
uses the current status of the BUC Switch and LNB Switch
(when used) to select the on-line stream.
NOTE
If the redundancy controller detects that the
switches are inconsistent, or cannot be detected,
it selects Stream 1.
When the redundancy controller is operating, it monitors the
two BUC and LNB (when used) streams for faults. When a
detectable fault occurs in the on-line BUC and LNB, and the
off-line BUC and LNB is serviceable, the redundancy
controller switches over the two streams. The interruption to
traffic is typically less than one second.
The redundancy controller switches:
•
the receive IF signals between the LNBs (when used)
and the modem equipment
•
the transmit RF signals between the BUCs and the
transmit antenna port
•
the receive RF signal between the receive antenna port
and the LNBs (when used)
The transmit IF signal is not switched. Rather, a splitter allows
the transmit IF signal to feed both BUCs simultaneously. In
transmit-only systems, a transmit-only connector assembly is
supplied and fitted to the LNB Switch Control connector.
20
Block Up Converter Systems 6700/6900 series User Guide
Overview
BUC faults
The redundancy controller uses a PLD to monitor the alarm
signals from both BUCs. The BUCs send alarm signals via
cables connected to the 14-way BUC 1 Control and BUC 2
Control connectors on the redundancy controller.
Red BUC 1/BUC 2 LEDs on the control panel of the
redundancy controller indicate that there is a fault with the
corresponding BUC or LNB. In transmit-only systems,
receive stream faults are not indicated. You should observe the
LED indicators on the BUC for details of the alarm condition.
For information on the LED indications on the BUC see
Table 11 on page 59. You can connect a Hand-held
Controller 6560 or a PC running terminal-emulating software
to the BUC 1 Serial and BUC 2 Serial connectors on the
redundancy controller, then diagnose the BUC faults as
required. For more information on using the hand-held
controller see the Hand-held and Remote Controller
6560/6570 User Guide. For more information on using serial
commands on a terminal see page 63, Serial interface
commands.
If you are using remote monitoring and control via a Remote
Controller 6570, the Fault LED for a BUC will illuminate if a
fault is detected. You can use the Faults menu in the remote
controller to diagnose the fault, and the Reset menu to clear
latched faults. For more information on using the remote
controller see the Hand-held and Remote Controller
6560/6570 User Guide.
Power supply
The redundancy controller is powered from the AC mains
supply.
Block Up Converter Systems 6700/6900 series User Guide
21
Overview
Auxiliary I/O interface of the redundancy controller
The Auxiliary I/O interface of the redundancy controller
enables you to perform the following functions remotely:
•
monitor operation of the redundancy switching system
using the isolated relay contacts
•
switch streams using external signals
Most of the remote control functions are achieved by
grounding the appropriate control signal to 0 V.
NOTE
The redundancy controller does not have a
serial remote control facility. However, serial
remote stream switching and monitoring of the
redundancy system alarms are available using
the BUC command set via either of the BUC 1
Serial/BUC 2 Serial connectors.
For details about the Auxiliary I/O interface of the redundancy
controller see page 51, Accessing the Auxiliary I/O interface
on the redundancy controller.
22
Block Up Converter Systems 6700/6900 series User Guide
Overview
RF waveguide switches
RF waveguide switches control both the receive and transmit
RF paths. The switches direct signals for both on-line and offline BUCs and LNBs (when used). Transmit/receive C-Band
systems may use either two RF waveguide switches or one
combined RF waveguide/coaxial switch. Transmit/receive
Ku-Band systems use two RF waveguide switches only.
Transmit-only C-Band or Ku-Band systems use only a single
RF waveguide switch.
Systems using two RF waveguide switches
In the receive path, a receive RF waveguide switch directs the
received RF from the receive port of the antenna feed to one of
the LNBs. The LNB waveguide inputs are coupled to ports 1
and 3 of the LNB switch. The switch is coupled via port 2 to
the WR229 (C-Band) or WR75 (Ku-Band) receive port of the
antenna. A blanking plate normally protects port 4 from the
weather.
In the transmit path, a transmit RF waveguide switch directs
the transmitted RF from the on-line BUC to the transmit port
of the antenna feed. The RF from the off-line BUC is directed
to either a coaxial or a waveguide load.
For transmit RF, the waveguide outputs of the BUCs are
connected to the WR137 (C-Band) or WR75 (Ku-Band) BUC
switch via short waveguide sections to ports 1 and 3. Port 2 of
the switch connects to the antenna via flexible waveguide. A
load or power attenuator terminates port 4 on the switch.
The redundancy controller verifies RF waveguide switching
by monitoring the tell-back contacts of both switches. If the
tell-back contacts indicate an abnormal condition, the BUC
Switch or LNB Switch LEDs on the control panel of the
redundancy controller illuminate red.
Block Up Converter Systems 6700/6900 series User Guide
23
Overview
Systems using a combined RF waveguide/coaxial
switch (C-Band only)
In the receive path, a receive RF waveguide switch directs the
received RF from the receive port of the antenna feed to one of
the LNBs.
In the transmit path, an RF coaxial switch directs the
transmitted RF from the on-line BUC to the transmit port of
the antenna feed. The RF from the off-line BUC is directed to
an appropriately-rated termination. The combined RF
waveguide/coaxial switch is controlled by a single cable,
which is connected to the LNB Switch Control connector
on the redundancy controller. The BUC Switch Control
connector is not used. The redundancy controller
automatically detects the presence of a combined switch and
configures its monitoring accordingly.
The combined RF waveguide/coaxial switch combines
waveguide and coaxial switching in a single assembly. The
switch is an electrically operated, 4-port WR229 waveguide
transfer switch, which is mechanically integrated with a 4-port
coaxial transfer switch for transmit RF.
The LNBs are directly coupled to ports 1 and 3 of the
combined RF waveguide/coaxial switch. The switch is
coupled via port 2 to the WR229 receive port of the antenna.
A blanking plate normally protects port 4 from the weather.
Coaxial cable connects the BUCs to ports 1 and 3 of the
N-type switch. The transmit antenna feed connects to port 2 of
the switch. A load or power attenuator connects to port 4.
The redundancy controller verifies RF waveguide switching
by monitoring the tell-back contacts to the combined RF
waveguide/coaxial switch. If the tell-back contacts indicate an
abnormal condition, the LNB Switch LEDs on the control
panel of the redundancy controller illuminate red.
NOTE
24
In the combined RF waveguide/coaxial switch
installation, the BUC Switch LEDs on the
control panel of the redundancy controller will
not illuminate.
Block Up Converter Systems 6700/6900 series User Guide
Overview
Systems using a single transmit RF waveguide
switch (transmit-only)
In the transmit path, a single transmit RF waveguide switch
directs the transmitted RF from the on-line BUC to the
transmit port of the antenna feed. The RF from the off-line
BUC is directed into an appropriately-rated termination. The
switch is controlled by a cable connected to the LNB Switch
Control connector.
The switch is an electrically operated, 4-port WR137 (for
C-Band) or WR75 (for Ku-Band) waveguide transfer switch.
The BUCs are connected to ports 1 and 3 of the switch. The
switch is coupled via port 2 to the transmit port of the antenna.
A load or power attenuator connects to port 4.
The redundancy controller verifies RF waveguide switching
by monitoring the tell-back contacts to the RF waveguide
switch. If the tell-back contacts indicate an abnormal
condition, the BUC Switch LEDs on the control panel of the
redundancy controller illuminate red.
Block Up Converter Systems 6700/6900 series User Guide
25
Overview
The Remote Controller 6570 and Hand-held
Controller 6560
The Remote Controller 6570 provides remote control and
monitoring facilities of the BUCs at a convenient indoor
location. The remote controller is connected via its BUC
Interface connector to the Auxiliary I/O connector on the
redundancy controller using the cable supplied.
The Hand-held Controller 6560 provides local control and
monitoring facilities of the BUCs at the outdoor-mounted
redundancy controller. A hand-held controller may be
connected to the BUC 1 Serial or BUC 2 Serial connector.
Alternatively, a BUC may be directly controlled by the handheld controller by disconnecting the M/C cable from the
M/C connector on the BUC, and connecting the hand-held
controller in its place.
26
Block Up Converter Systems 6700/6900 series User Guide
2
Installation
CODAN
This section contains the following topics:
Unpacking the equipment (28)
Installing the BUC equipment (28)
Cable recommendations (32)
Serial interfaces (37)
Connecting the serial interface (39)
Monitor and control interface of the BUC (40)
Installing the redundancy system (42)
Serial interfaces of the BUCs from the redundancy
controller (50)
Accessing the Auxiliary I/O interface on the redundancy
controller (51)
Setting up the redundancy switching equipment (53)
Block Up Converter Systems 6700/6900 series User Guide
27
Installation
Unpacking the equipment
Ensure that the packing boxes are upright as indicated by the
printing on the boxes. Open each box and check for signs of
damage to the equipment. If you notice any damage, contact
Codan immediately to obtain an RMA. Failure to contact
Codan before returning the unit may result in any warranty
being void.
Installing the BUC equipment
All equipment that is mounted outdoors must be
adequately weatherproofed.
Ensure all waveguide joints are properly sealed
WARNING with the appropriate gasket.
Use self-amalgamating tape to seal connectors
and cable entry points from the connector to the
cable sheath.
CAUTION
Water is the most common cause of poor
performance in VSAT installations. Ensure that
all cables and waveguide junctions are properly
sealed.
A radiation hazard exists if the BUC is operated
WARNING with its RF output unterminated (see page 123,
Radiation safety).
28
Block Up Converter Systems 6700/6900 series User Guide
Installation
TRF and LNB
The TRF and LNB are normally mounted directly on the
antenna feed structure.
The LNB obtains the required +15 to +24 V DC power and, in
certain cases, the 10 MHz reference signal from a compatible
L-Band modem. The modem is connected to the receive
output connector of the LNB.
BUC
BUCs are supplied with either N-type or waveguide outputs.
A mounting kit is supplied with the BUC. Some mounting kits
allow the BUC to be mounted on the boom or pedestal of the
antenna. Other kits may also be available for different
mounting options. Contact your antenna manufacturer if you
have specific installation requirements.
Cables
Use an IF coaxial cable to connect the modem to the BUC (see
page 32, Cable recommendations). It is recommended that you
use the same type of cable to connect the modem to the LNB.
If you are using the RS232/422 serial interface, use an M/C
cable to connect the BUC to a PC (see page 40, Monitor and
control interface of the BUC).
DC power connection
There are two types of BUCs that are DC-powered: those
powered via the IF INPUT connector, and those powered via
an external connector.
BUCs that are powered via the IF INPUT connector receive
DC power from a source via the IF cable. See BUC
specifications or compare your BUC model number against
Table 27 on page 111 for the exact voltage range of your BUC.
Block Up Converter Systems 6700/6900 series User Guide
29
Installation
BUCs that are externally powered from a DC source require
appropriate DC power from an external source. See BUC
specifications or compare your BUC model number against
Table 27 on page 111 for the exact voltage range of your BUC.
Certain BUCs with external DC power
connectors may also have auto-sensing circuits,
and can be powered from either the external
connector or via the IF INPUT connector. If
both connectors are powered, the external
connector is automatically selected.
NOTE
AC mains connection
AC-powered BUCs operate with any AC input voltage in the
range 115–230 V AC. Check BUC specifications for the exact
voltage range of your BUC.
WARNING
Voltages outside of these limits may cause
damage to the BUC.
To connect the BUC to the AC mains:
1
Connect the AC power lead to the AC mains supply.
Before applying power to the BUC, ensure
that the installation complies with the
WARNING safety precautions listed on page 123,
Electromagnetic compatibility and safety
notices.
1
Ensure the isolating switch for the AC supply is switched
off.
1
Connect the AC power lead to the AC INPUT connector
on the BUC.
If you need to make your own AC mains cable, or reterminate
the cable supplied, Table 8 lists the pin connections and
describes the input functions available on the AC INPUT
connector on the BUC.
30
Block Up Converter Systems 6700/6900 series User Guide
Installation
Table 8: Pinouts of the AC INPUT connector
(Amphenol T 3110 000)
Pin
Description
1
Neutral
2
Not connected
3
Active
Protective earth
It is recommended that BUCs are installed as close as possible
to the antenna feed to minimise losses.
CAUTION
Heavier BUCs may need to be mounted further
down the boom to minimise the mechanical
leverage load on the antenna.
If the waveguide output of each BUC is attached directly to
the RF waveguide switch with a rigid connection, ensure that
there are no undue stresses on the waveguide section when the
flange hardware is tightened. Tighten the BUC mounting
screws last. The long mounting rails have oversized holes to
enable the BUC to be secured in the exact position required,
which avoids stressing the rigid waveguide component.
Block Up Converter Systems 6700/6900 series User Guide
31
Installation
Cable recommendations
Table 9 lists the recommended specifications for IF coaxial
cables used in your system. These specifications place
restrictions on the maximum length of the transmit IF cable.
The limiting factor is most likely the 20 dB maximum cable
loss. Cables that have 20 dB cable loss at L-Band frequencies
usually have DC loop resistances much less than those shown
below.
Table 9:
Recommendations for IF coaxial cables
Characteristic
Recommendation
Cable loss at operating
frequency
20 dB maximum
DC loop resistance
2 Ω maximum (+48 V BUC)
1 Ω maximum (+24 V BUC)
Screening
100 dB minimum
Nominal impedance
50 Ω
Connectors
BUC end: N-type male
connector
Indoor end: connector to suit the
modem used
Cable loss specification
The recommended maximum cable loss is derived from the
maximum output power normally provided by modems and
the maximum gain of the BUC.
32
Block Up Converter Systems 6700/6900 series User Guide
Installation
DC loop resistance specification
The maximum DC loop resistance is determined by the DC
power drawn by a BUC and its minimum operating input
voltage. Some BUCs are not powered via the cable, so the DC
loop resistance of the IF cable is not a consideration for such
BUC installations.
CAUTION
To ensure correct operation, the DC loop
resistance figure must not be exceeded.
Cable screening specification
Cable screening is derived from regulatory requirements
related to the radiation of spurious signals from the antenna.
Screening is more critical if the BUC is co-located with other
radio transmitting equipment, for example, mobile-phone
towers.
Cable lengths
Table 10 shows the maximum lengths of different types of
cables to ensure the 20 dB loss recommendation is not
exceeded. The cable lengths are shown in metres and feet.
Table 10:
Cable lengths resulting in a 20 dB loss
Frequency
(MHz)
RG223
(m (ft))
Belden 9914
(m (ft))
Belden 9913F
(m (ft))
Times
Microwave
LMR-400
(m (ft))
950
43 (141)
104 (341)
125 (410)
150 (492)
1450
34 (111)
81 (266)
99 (325)
120 (394)
1700
31 (102)
74 (243)
91 (299)
111 (364)
1750
31 (102)
73 (240)
89 (292)
109 (358)
Block Up Converter Systems 6700/6900 series User Guide
33
Installation
IF levels
The figures and tables in this section show the single carrier IF
levels required to achieve rated P1dB output power from the
BUC using various types and lengths of IF cables. Your actual
IF levels may be different from those shown if you are
operating with multiple carriers and you require output back
off to control intermodulation product levels.
Examples are provided for short cables (with a 3 dB loss) and
long cables (with a 20 dB loss).
The figures in this section are provided as examples only. You
should determine the loss of your selected cable from its
length and your operating frequency (see Table 10 on
page 33). You can then set the modem IF output level and the
BUC attenuator to achieve the required output power.
As a general principle, you should set the BUC attenuator at
the highest possible attenuation setting given the available
modem IF output power and the cable loss. This reduces the
susceptibility of the system to external interference.
34
Block Up Converter Systems 6700/6900 series User Guide
Installation
Using short IF cables
Figure 11 shows the IF levels required when using short IF
cables such as the following:
•
5 m RG223
•
12 m 9914
•
15 m 9913F
•
18 m LMR-400
Figure 11:
IF levels required for short cables
Modem
IF cable
BUC
Gain
–3 dB
BUC gain –
attenuator
setting
Input/output
level
–16 dBm
–19 dBm
–19 dBm +
(BUC gain –
attenuator setting)
Refer to the relevant specifications sheets for the detailed specifications for your BUC
Block Up Converter Systems 6700/6900 series User Guide
35
Installation
Using long IF cables
Figure 12 shows the IF levels required when using long IF
cables such as the following:
•
34 m RG223
•
80 m 9914
•
100 m 9913F
•
120 m LMR-400
Figure 12:
IF levels required for long cables
Modem
IF cable
BUC
Gain
–20 dB
BUC gain –
attenuator
setting
Input/output
level
–7 dBm
–27 dBm
–27 dBm +
(BUC gain –
attenuator setting)
Refer to the relevant specifications sheets for the detailed specifications for your BUC
36
Block Up Converter Systems 6700/6900 series User Guide
Installation
Serial interfaces
The following serial interfaces are provided:
•
RS232 and RS422/485 available on the M/C connector
on the BUC
•
FSK available on the IF INPUT connector on the BUC
RS232 interface
The RS232 serial interface supports both the ASCII and the
Codan packet protocols simultaneously. Responses to
commands are returned in the same protocol format as they
are sent. The RS232 serial interface operates with the
following parameters:
data rate
9600 bps
word length
8 bits
parity
none
stop bit
1
The fixed data rate and protocol simplifies the connection
during installation and commissioning, and enables a PC
running a terminal-emulation program to be used to configure
the BUC. For information on protocols, contact your Codan
representative.
The BUC is able to detect the connection of an RS232
interface. When an RS232 interface is used, the BUC inhibits
the use of the Set and Reset commands on the RS422/485 and
FSK interfaces. View and Output commands can still be used
on these interfaces. This functionality is provided for safety
reasons.
NOTE
If you disabled transmission, don’t forget to
re-enable it before you remove the RS232
connection.
Block Up Converter Systems 6700/6900 series User Guide
37
Installation
For example, a technician working on a BUC at the antenna
can make an RS232 connection and disable transmissions.
Transmissions cannot be re-enabled at another source, but the
other interfaces can still monitor the BUC parameters. When
the RS232 connection is removed and transmission is restored
using the RS232 interface, normal monitor and control
operation is restored.
RS422/485 interface
The RS422/485 interface can be operated in either 2-wire or
4-wire mode. The RS422/485 interface enables monitor and
control of the BUC over long distances using other protocols
that are not available for use with the RS232 interface.
FSK interface
The FSK interface enables monitor and control of the BUC
over long distances using other protocols that are not available
for use with the RS232 interface. The FSK interface does not
require an extra monitor and control serial cable, but does
require a modem with FSK monitor and control capability. If
an appropriate modem is not available, contact your Codan
representative to find out what accessories are available to
access the FSK interface.
38
Block Up Converter Systems 6700/6900 series User Guide
Installation
Connecting the serial interface
To set the operating parameters of the BUC, the BUC must be
connected to a terminal (for example, a Hand-held Controller
6560, a Remote Controller 6570, a PC, or an organiser
emulating a terminal).
The connection may be permanent as part of the installation or
temporary for the purpose of setting the operating parameters
of the BUC.
Permanent interface connection
A permanent interface connection can be provided via the
monitor and control interface of the BUC (see Figure 13 on
page 41). The RS232 serial interface may only be used for
distances less than 15 m. The RS422/485 serial interface may
be used for distances up to approximately 1 km.
The Remote Controller 6570 is designed as a permanent
interface connection and is supplied with a standard 50 m
cable.
Temporary interface connection
A serial interface cable is available to connect the BUC to the
RS232 serial port of a PC or an organiser emulating a
terminal, or you may connect a Hand-held Controller 6560.
If using a PC, connect the cable between the M/C connector of
the BUC and the serial port of the PC. This cable provides a
14-way female MS-style connector to 9-way D-type female
connector for connection to the PC. If connection to a 25-way
D-type serial port is required, use a standard 25-way female to
9-way male adaptor.
Block Up Converter Systems 6700/6900 series User Guide
39
Installation
Monitor and control interface of the BUC
The monitor and control interface of the BUC provides a relay
contact to indicate the fault status of the BUC. See Figure 13
for the pin assignments of the M/C connector. A
MIL-C-26482 12-14P connector (for example,
MS3116F12-14P) is required to mate with the M/C connector.
40
Block Up Converter Systems 6700/6900 series User Guide
Installation
Figure 13:
Monitor and control interface of the BUC
M
+10 V
H
0V
1k
+5 V
+10 V DC (nominal)
output (150 mA max.)
C
120
*
L
RS422/485 Rx–
1k
1k
+5 V
RS422/485 Rx+
B
120
*
F
1k
+12 V
10 k
D
E
A
K
J
+2.5 V
R
+
+5 V
N
+
RS232 RxD
RS232 TxD
Summary Alarm
(open on alarm
30 V @ 1 A max.)
LNB Fault
+5 V
Redundancy Controller
Fault
1k5
–
Not connected
1k5
–
RS422/485 Tx–/Rx–
(RS422/485 TxA/RxA)
1k5
–
+5 V
RS422/485 Tx+/Rx+
(RS422/485 TxB/RxB)
+
P
On-line Input/Output
*Bus termination resistors
Block Up Converter Systems 6700/6900 series User Guide
41
Installation
Installing the redundancy system
Mounting the redundancy controller
The redundancy controller has two mounting flanges. Each
flange has 10 mounting holes. If you are going to use the
mounting kit supplied, fitting instructions are provided in the
kit.
Mount the redundancy controller upright on or near the
antenna structure. A protected position is preferable however,
the redundancy controller can withstand exposure to outdoor
conditions.
Installing separate transmit and receive RF waveguide
switches
WARNING
Handle the switches with care. They are easily
damaged.
Transmit RF waveguide switch
To install the transmit RF waveguide switch (BUC switch):
1
42
Connect ports 1 and 3 of the transmit RF waveguide
switch to the BUC outputs using the waveguide sections
and flange kits as shown in the mounting drawings.
NOTE
In C-Band installations, use the appropriate
flange kit.
NOTE
In Ku-Band installations, ensure the
appropriate o-ring is used, otherwise
sealing will be compromised or correct
mating of the waveguide flanges will not
be possible.
Block Up Converter Systems 6700/6900 series User Guide
Installation
1
Connect port 2 of the transmit RF waveguide switch to
the transmit flange of the antenna feed using gasket kits
and rigid or flexible waveguide as appropriate.
NOTE
1
If connecting the Ku-Band transmit RF
waveguide switch to a waveguide section
that has clearance holes for 6-32 UNC
hardware, a waveguide adaptor kit is
available.
Connect the off-line BUC load to port 4 of the transmit
RF waveguide switch as shown in the mounting
drawings.
CAUTION
Ensure all joints are completely
weatherproof.
NOTE
Spare flange kits are provided with the
redundancy package. The universal
Ku-Band flange kit contains a selection of
flat gaskets and circular cross-section
gaskets (both large and small
cross-sectional diameter).
1
In transmit-only systems, fit the transmit-only connector
assembly to the LNB Switch Control connector.
1
Connect the transmit RF waveguide switch to the BUC
Switch Control connector using the cable supplied.
Block Up Converter Systems 6700/6900 series User Guide
43
Installation
Receive RF waveguide switch (transmit/receive
systems only)
To install the receive RF waveguide switch (LNB switch):
1
Fit the TRF (if used) to the receive port of the antenna
feed using the appropriate flange kit for C-Band and
Ku-Band, selecting the correct gasket.
1
Hold waveguide port 2 of the receive RF waveguide
switch against the receive port of the antenna feed or
TRF (if fitted). Decide which way the switch is to face.
1
For Ku-Band installations, attach the 2" rigid WR75
waveguide sections to ports 1 and 3 of the receive RF
waveguide switch using the appropriate flange kit.
1
Attach the LNBs to:
• ports 1 and 3 of the receive RF waveguide switch using
the appropriate flange kit for C-Band
• the 2" rigid waveguide sections using the appropriate
flange kit for Ku-Band
NOTE
44
For Ku-Band installations, ensure the
appropriate o-ring is used, otherwise
sealing will be compromised or correct
mating of the waveguide flanges will not
be possible.
1
1
Clamp the gaskets tightly to ensure perfect seals.
1
If you want to allow for dry air pressurisation, fit the
supplied air nozzle to the blanking plate. If this is not
required, fit the M5 screw with seal into the blanking
plate.
1
Attach the receive RF waveguide switch to the receive
port of the antenna feed using the appropriate flange kit.
If the blanking plate was not factory fitted, attach it to
port 4 of the receive RF waveguide switch using the
appropriate flange kit.
Block Up Converter Systems 6700/6900 series User Guide
Installation
If connecting the Ku-Band receive RF
waveguide switch to a receive port of the
antenna feed that has clearance holes for
6-32 UNC hardware, a waveguide adaptor
kit is available.
NOTE
1
Spare flange kits are provided with the
redundancy package. The universal
Ku-Band flange kit contains a selection of
flat gaskets and circular cross-section
gaskets (both large and small crosssectional diameter).
Connect the receive RF waveguide switch to the LNB
Switch Control connector using the cable supplied.
Installing the combined RF waveguide/coaxial switch
(C-Band transmit/receive systems only)
WARNING
Handle the switch with care. It is easily
damaged.
To install the combined RF waveguide/coaxial switch:
1
Fit the TRF (if used) to the receive port of the antenna
feed using the appropriate flange kit.
1
Hold waveguide port 2 of the combined RF
waveguide/coaxial switch against the antenna receive
feed. Decide which way the switch is to face.
1
Attach the LNBs to ports 1 and 3 of the RF waveguide
section of the switch using the appropriate flange kit.
1
1
Clamp the gaskets tightly to ensure perfect seals.
If the blanking plate was not factory fitted, attach it to
port 4 of the waveguide section of the switch using the
appropriate flange kit (see the mounting and
interconnection drawings).
Block Up Converter Systems 6700/6900 series User Guide
45
Installation
1
If you want to allow for dry air pressurisation, fit the
supplied air nozzle to the blanking plate. If this is not
required, fit the M5 screw with seal into the blanking
plate.
1
Connect the off-line BUC termination to port 4 of the
coaxial section of the switch as shown in the mounting
and interconnection drawings.
NOTE
1
Connect the outputs of the BUCs to the corresponding
N-type connectors of the coaxial section of the switch
using the coaxial cables supplied.
1
Connect port 2 of the coaxial section of the switch to the
transmit port of the antenna feed using the coaxial cable
supplied.
1
Seal all N-type connections with self-amalgamating tape.
1
CAUTION
Ensure all joints are completely
weatherproof.
NOTE
Spare flange kits are supplied with the
redundancy package to provide for various
installation requirements.
Connect the combined RF waveguide/coaxial switch to
the LNB Switch Control connector using the cable
supplied.
NOTE
46
In some configurations, the termination
consists of multiple parts.
The BUC Switch Control connector is
not used in this configuration.
Block Up Converter Systems 6700/6900 series User Guide
Installation
Connecting the power cables
The redundancy controller is AC mains powered.
To connect the power cable to the redundancy controller:
1
Connect the supplied cable to the AC Power Input
connector on the redundancy controller.
Block Up Converter Systems 6700/6900 series User Guide
47
Installation
Connecting the control cables
To connect the control cables:
1
Connect the BUC 1 Control connector and the BUC 2
Control connector on the redundancy controller to the
corresponding M/C connector on each BUC using the
control cables supplied.
For high-power BUC systems, connect the BUC 1
Control connector and the BUC 2 Control connector
on the redundancy controller to the corresponding
M/C connector on each BUC and the corresponding
CONTROL connector on each high-power SSPA using
the specific control cables supplied.
Connecting the IF from the redundancy controller to the
BUCs
To connect the IF cables:
1
Connect the Tx IF Output 1 connector and the Tx IF
Output 2 connector on the redundancy controller to the
corresponding IF INPUT connector on each BUC using
the coaxial cables supplied.
Connecting the IF cables between an L-Band IF modem (or
other equipment) and the redundancy controller
To connect the IF cables:
48
1
Connect the transmit IF output connector on the L-Band
IF modem (or other equipment) to the Tx IF Input
connector on the redundancy controller using a suitable
coaxial cable.
1
In systems other than transmit-only, connect the receive
IF input connector on the L-Band IF modem (or other
equipment) to the Rx IF Output connector on the
redundancy controller using a suitable coaxial cable.
Block Up Converter Systems 6700/6900 series User Guide
Installation
Connecting the IF from the LNBs to the redundancy
controller
To connect the IF cables:
1
Connect the corresponding N-type IF output connector
on each LNB to the Rx IF Input 1 connector and the Rx
IF Input 2 connector on the redundancy controller using
the coaxial cable supplied.
Grounding the installation
To ground the installation:
1
Connect a separate earth strap from the protective earth
terminal on each unit directly to the common earth stake.
Block Up Converter Systems 6700/6900 series User Guide
49
Installation
Serial interfaces of the BUCs from the
redundancy controller
The M/C connector on each BUC includes the serial interface
of the BUC. Although the redundancy controller plugs into
this connector, the redundancy controller uses relay contacts to
communicate with the BUC.
You can access the serial interface of each BUC via the
14-way BUC 1 Serial or BUC 2 Serial connector on the
redundancy controller. These connectors are suitable for
temporary connection of a PC or Hand-held Controller 6560
as they have the same RS232 serial pin connections as the
M/C connector on the BUC.
The RS485 serial interfaces for both BUCs are included in the
19-way Auxiliary I/O connector interface of the redundancy
controller for remote monitor and control applications via the
Remote Controller 6570.
50
Block Up Converter Systems 6700/6900 series User Guide
Installation
Accessing the Auxiliary I/O interface on the
redundancy controller
Remote control and monitoring of the redundancy switching
system is accessible via the 19-way Auxiliary I/O connector
on the redundancy controller.
To use this 19-way connector, you need a 19-way
Mil-C-26482 series plug, part number MS3116J14-19P.
Figure 14 on page 52 shows the monitor and control interface
at the Auxiliary I/O connector of the redundancy controller.
Contacts are shown in their de-energised state.
Relay contacts indicate the following faults and operational
status of the redundancy system (the four relay contacts share
a common contact connection):
•
Stream 1 Fault
•
Stream 2 Fault
•
Stream Selected
•
Redundancy Controller Fault
Inputs are provided to allow remote control via contact
closures:
•
control source
•
Auto or Manual Mode
•
stream selection
The RS485 connections parallel the two BUC RS485
interfaces to enable remote control of both BUCs using a
Remote Controller 6570, or using serial commands with a PC
running terminal-emulating software.
Block Up Converter Systems 6700/6900 series User Guide
51
Installation
Figure 14:
controller
Auxiliary I/O interface of the redundancy
U
+12 V
BUC 1
D
250 mA
B
A
Tx Data ‘A’ (RS422/485)
T
M
L
V
+12 V
3k3
+12 V
3k3
+12 V
3k3
J
Tx Data ‘B’ (RS422/485)
Stream 1 Fault
Stream 2 Fault
Redundancy Controller
Fault
Relay Common
Stream Selected
(open = Stream 1)
Remote
Control
Disable
Enable
K
Auto
N
Mode
Manual
F
G
H
52
Rx Data ‘A’ (RS422/485)
Rx Data ‘B’ (RS422/485)
S
Alarm contacts
open on fault
GND
C
P
BUC 2
+12 V
Stream
Select
Stream 1
Stream 2
Block Up Converter Systems 6700/6900 series User Guide
Installation
Setting up the redundancy switching
equipment
To set up the redundancy switching equipment:
1
Set the AC voltage selector on the control panel of the
redundancy controller to the appropriate voltage for your
operating environment.
1
1
1
Switch on the modem(s), then switch off the carrier(s).
Apply power to the redundancy controller and the BUCs.
Connect a Hand-held Controller 6560 to the BUC 1
Serial connector, then to the BUC 2 Serial connector
on the redundancy controller, and set the following
parameters:
Parameter
Menu
Setting
Tx state
Control
Tx off (initially)
Redundancy
mode
Auxiliary
Hot standby
(preferred)
Warm standby
IF comp freq/RF Main
comp freq
Tx attenuation
Main
LO
Auxiliary
Tx default
Auxiliary
Block Up Converter Systems 6700/6900 series User Guide
Both BUCs must
have the same
settings
53
Installation
1
1
Parameter
Menu
Setting
Serial parity
Auxiliary
Serial stop bits
Auxiliary
RS485
termination
Auxiliary
Serial protocol
Auxiliary
Serial address
Auxiliary
For information on
the required serial
parameters for a
Remote
Controller 6570 see
the Hand-held and
Remote Controller
6560/6570 User
Guide
Serial echo
Auxiliary
Set the Online state of the required BUC to Online.
Set the Tx state of both BUCs to Tx on.
NOTE
If the Redundancy mode is Warm
standby, the output from the power
amplifier in the off-line BUC is not
enabled.
NOTE
High-power SSPAs in a high-power BUC
system must be configured for stand-alone
use in BUC stream redundancy. For more
information on high-power systems see the
relevant SSPA documentation.
The control panel of the redundancy controller shows the
stream selection states. All fuse LEDs and BUC/LNB LEDs
should be green.
54
NOTE
In transmit-only systems, the LNB fuse LEDs
remain green and the LNB 1 and LNB 2 LEDs
are always off.
NOTE
In C-Band systems that use a combined RF
waveguide/coaxial switch, the BUC 1 and
BUC 2 LEDs are always off.
Block Up Converter Systems 6700/6900 series User Guide
Installation
Connecting the remote controller
The optional Remote Controller 6570 is connected to the
Auxiliary I/O connector on the redundancy controller using a
19-way cable.
NOTE
Before connecting a Remote Controller 6570,
you should ensure that the serial address and
packet protocol in each BUC has been set up
correctly using a Hand-held Controller 6560, or
other serial device such as a PC. For more
information see the Hand-held and Remote
Controller 6560/6570 User Guide.
To connect the remote controller:
1
Plug the 25-way D-type socket on the 19-way cable into
the BUC Interface connector on the rear of the remote
controller.
1
Plug the 19-way MS plug on the 19-way cable into the
Auxiliary I/O connector on the redundancy controller.
Block Up Converter Systems 6700/6900 series User Guide
55
Installation
This page has been left blank intentionally.
56
Block Up Converter Systems 6700/6900 series User Guide
3
Setting up and operating the
BUC system
CODAN
This section contains the following topics:
Switching on the BUC (58)
LED indicators (59)
Serial interface monitor and control (62)
Serial interface commands (63)
Switching the redundancy system on and off (76)
Checking the operation of the LED indicators and
controls (76)
Switching between streams (76)
Controlling the redundancy system (78)
Block Up Converter Systems 6700/6900 series User Guide
57
Setting up and operating the BUC system
Switching on the BUC
CAUTION
Ensure that the modem provides the correct DC
voltages to power the particular BUC and LNB
models being used.
To switch on the BUC:
1
Switch on the modem, and if you have installed an
externally-powered BUC, switch on the power to the
BUC.
1
If you need to set up the BUC, switch off the carrier at
the modem.
Connect the BUC to a PC (see page 39, Connecting the
serial interface), then set up the BUC using the Set
commands in Table 14 on page 65.
Switch on the carrier at the modem.
58
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
LED indicators
There are three LED indicators on the BUC. These LEDs
indicate the state of the BUC (see Table 11).
Table 11:
LED indicators on the BUC and their states
LED
State
Indicates...
PWR
Green
Power is supplied to the BUC
Tx
Yellow
The BUC PA is on
FLT
Off
No faults or latched faults are present
Constant red
One or more of the following hardware faults have
been detected in the BUC:
• overtemperature fault (> 90°C)
• PA fault
• LO fault
• fan fault
• output power threshold
• hardware/firmware incompatibility
For information on fault finding see page 81,
Maintenance and fault finding
One or more of the following faults have been
Flashing red
(2 flashes every detected in the system:
second)
• an external fault in the LNB (when in redundancy
configuration only)
• an external fault in the redundancy controller (when
in redundancy configuration only)
• a non-volatile memory fault in the BUC
Flashing red
(1 flash every
2 seconds)
NOTE
The fault information from a latched fault has been
stored, however the fault is no longer present
(firmware V1.10 or earlier)
Use the VFS command to view the fault status.
Block Up Converter Systems 6700/6900 series User Guide
59
Setting up and operating the BUC system
The control panel of the redundancy controller has groups of
LEDs that indicate the status of the redundancy system and its
fuses.
Table 12: LED indicators on the control panel of the
redundancy controller
LED
Colour
Indicates...
BUC 1
green
BUC 1 is OK
In a high-power BUC system, the BUC and
high-power SSPA in Stream 1 are OK
red
BUC 1 or LNB 1 is faulty
In a high-power BUC system, the BUC, highpower SSPA or LNB in Stream 1 is faulty
BUC 2
green
BUC 2 is OK
In a high-power BUC system, the BUC and
high-power SSPA in Stream 2 are OK
red
BUC 2 or LNB 2 is faulty
In a high-power BUC system, the BUC, highpower SSPA or LNB in Stream 2 is faulty
LNB 1
LNB 2
BUC Switch
LNB Switch
60
green
LNB 1 is OK
red
LNB 1 is faulty
green
LNB 2 is OK
red
LNB 2 is faulty
green
BUC transmit waveguide switch is OK (LED
pairs indicate switch position)
red
Switch is faulty (all four LEDs are red)
green
LNB receive waveguide or combined
transmit/receive switch is OK (LED pairs
indicate switch position)
red
Switch is faulty (all four LEDs are red)
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 12: LED indicators on the control panel of the
redundancy controller (cont.)
LED
Colour
Redundancy
green
Controller Status
red
Indicates...
Redundancy system and switches are OK
Redundancy system is faulty or switches are
inconsistent
Remote
Controller fuse
green
Remote controller fuse OK
red
Remote controller fuse has blown
BUC 1/BUC 2
fuse
green
BUC 1 or BUC 2 fuse is OK
red
BUC 1 or BUC 2 fuse has blown
LNB 1/LNB 2 fuse green
LNB 1 or LNB 2 fuse is OK
red
LNB 1 or LNB 2 fuse has blown
NOTE
The LNB 1, LNB 2 and LNB Switch LEDs
are fitted, but not operational in transmit-only
systems.
Block Up Converter Systems 6700/6900 series User Guide
61
Setting up and operating the BUC system
Serial interface monitor and control
To view or change the operating parameters of the BUC, the
BUC must be connected to a terminal (for example, a Handheld Controller 6560, a Remote Controller 6570, a PC, or an
organiser emulating a terminal).
To establish communications between the PC and the BUC see
page 39, Connecting the serial interface.
For more advanced remote control applications, contact your
Codan representative.
The BUC is monitored and controlled using 3-letter operating
commands followed, in some cases, by data. These commands
are described in Table 13 to Table 17.
NOTE
62
The commands listed in Table 13 to Table 17
are used with common installations. If you have
other requirements for your installation, contact
your Codan representative for the facilities and
commands available.
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Serial interface commands
This section describes the serial interface commands you can
use to set parameters and display information about the BUC.
The descriptions given are based on using ASCII protocol.
The commands consist of a 3-letter mnemonic and, in some
cases, command data.
Generally, the first letter of the command determines the type
of command (that is, H = Help, S = Set, O = Output,
V = View, R = Reset) and the last two letters uniquely define
the command.
The BUC is insensitive to the case of the command text.
NOTE
For example output of a command set see
page 115, Example outputs for the View
commands.
For the...
See...
Help commands
Table 13 on page 64
Set commands
Table 14 on page 65
Output commands
Table 15 on page 72
View commands
Table 16 on page 73
Reset commands
Table 17 on page 74
Block Up Converter Systems 6700/6900 series User Guide
63
Setting up and operating the BUC system
Table 13:
Help commands
Command
Function
Enter... Data required
Help
Lists the Help commands.
HLP
None
Help for Set
commands
Lists the Set commands and HSC
the possible settings.
None
NOTE
Some settings are
dependent on the
model of the BUC,
or another setting.
Help for
Output
commands
Lists the Output commands. HOC
None
Help for
View
commands
Lists the View commands.
HVC
None
Help for
Reset
commands
Lists the Reset commands.
HRC
None
64
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 14:
Set commands
Command
Function
Enter... Data required
Set transmit
on
Switches transmit on or off
by controlling the PA of the
BUC.
STOn
n = 0, switches transmit off
n = 1, switches transmit on
To switch on the PA, all three
serial interfaces (RS232,
RS422/485 and FSK) must
be set to STO1. STO1 is the
default setting for all of the
serial interfaces.
A built-in safety feature only
allows transmit to be
switched on via the interface
that was used to switch it off
originally.
STO1 cannot be used to
switch on transmit if an
internal fault has occurred in
the BUC.
NOTE
For CE-certified
operation you
must set the
transmit default
state to Off
(STD0). When
STD0 is used (see
page 69, Set
transmit default),
you must use
STO1 after
powerup to switch
transmit on.
Block Up Converter Systems 6700/6900 series User Guide
65
Setting up and operating the BUC system
Table 14:
Command
Set commands (cont.)
Function
Enter... Data required
Set
Sets either the IF or RF
compensation compensation frequency of
frequency
the carrier in MHz.
The BUC determines from
the value entered whether
you have set the IF or RF
compensation frequency, and
calculates the corresponding
RF or IF compensation
frequency.
The IF or RF compensation
frequency range is dependent
on the model of the BUC and
the LO setting.
The BUC uses the specified
RF frequency for the internal
temperature compensation
and other calibration
functions. It does not affect
the carrier frequency.
If the carrier frequency is
unknown, set the IF or RF
compensation frequency to
zero.
If multiple carriers are being
transmitted and the
frequency is limited to a
narrow band (for example,
over one transponder), set the
IF or RF compensation
frequency to the nominal
centre frequency of the
operating band.
66
SCFn
For C-Band Standard and
Extended frequency band
BUCs:
LO = 7300 MHz
IF: 950 ≤ n ≤ 1450
RF: 5850 ≤ n ≤ 6350
LO = 7375 MHz
IF: 950 ≤ n ≤ 1525
RF: 5850 ≤ n ≤ 6425
LO = 7600 MHz
IF: 950 ≤ n ≤ 1750
RF: 5850 ≤ n ≤ 6650
LO = 7675 MHz
IF: 950 ≤ n ≤ 1750
RF: 5925 ≤ n ≤ 6725
For Ku-Band Standard and
Extended frequency band
BUCs:
LO = 15450 MHz
IF: 950 ≤ n ≤ 1700
RF: 13750 ≤ n ≤ 14500
LO = 15450 MHz
IF: 950 ≤ n ≤ 1450
RF: 14000 ≤ n ≤ 14500
Use n = 0 for broadband
operation (this forces
broadband calibration data
to be used)
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 14:
Set commands (cont.)
Command
Function
Enter... Data required
Set transmit
attenuator
Sets the transmit attenuator
of the BUC in dB.
STAn
To minimise the possible
effects of interference it is
preferable to have a high
transmit attenuation and a
high IF level from the
modem. Therefore, the BUC
attenuator should be set as
high as possible, consistent
with the required BUC
output power, transmit IF
cable loss and maximum IF
output level capability of the
modem.
SATn
Set transmit Sets the transmit power
power alarm alarm threshold in dBm.
threshold
The allowable threshold
range depends upon the
model of the BUC. Use VLD
to display the upper and
lower limits of the allowable
range for your BUC (see
page 73, View limit data).
n = 0 to 12 dB
Certain firmware versions
allow 4 dB steps, while
other firmware versions
allow 1 dB steps.
n = value within the
allowable threshold range
for your BUC
n = 0, disables the transmit
power alarm
If the transmit power falls
below the set threshold, a
transmit power alarm is
generated.
Block Up Converter Systems 6700/6900 series User Guide
67
Setting up and operating the BUC system
Table 14:
Command
Set commands (cont.)
Function
Enter... Data required
Set burst
Sets the burst mode power
mode power threshold in dBm.
threshold
When you set a
new burst mode
power threshold,
the current,
minimum and
NOTE maximum burst
power readings
are reset to zero
(see page 72,
Output burst
powers).
SBTn
n = value within the
allowable threshold range
for your BUC
n = 0, disables burst
detection
You can set the threshold
level above which
transmitted TDMA bursts or
similar signals are recorded.
The allowable threshold
range depends upon the
model of the BUC. Use VLD
to display the upper and
lower limits of the allowable
range for your BUC (see
page 73, View limit data).
68
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 14:
Set commands (cont.)
Command
Function
Enter... Data required
Set local
oscillator
Sets the LO frequency in
MHz.
SLOn
NOTE
NOTE
Set transmit
default
Before you change
the LO setting you
should switch off
transmission using
STO0.
It is not necessary
to use SLOn with
Ku-Band BUCs as
they only have one
LO frequency.
Sets the default transmit state STDn
at powerup.
NOTE
For CE-certified
operation you
must set the
transmit default
state to Off
(STD0). When
STD0 is used you
must use STO1
after powerup to
switch transmit on
(see page 65, Set
transmit on).
Set redundant Sets the BUC to operate in a SRMn
mode
redundancy system.
NOTE
For a system
without
redundancy you
must always set
the redundant
mode to zero.
Block Up Converter Systems 6700/6900 series User Guide
For C-Band Standard
frequency range BUCs:
n = 7300 or 7375 MHz
For C-Band Extended
frequency band BUCs:
n = 7300, 7375, 7600 or
7675 MHz
n = 0, keeps transmit off
(that is, PA off) at powerup
n = 1, returns to transmit
state prior to last
powerdown
n = 0, system without
redundancy
n = 1, warm standby
system
n = 2, hot standby system
69
Setting up and operating the BUC system
Table 14:
Set commands (cont.)
Command
Function
Enter... Data required
Set on line
Sets the on-line or off-line
state of the BUC in a warm
standby or hot standby
redundant system, that is,
SRM1 or SRM2 has been
set.
SOLn
NOTE
Set serial
interface
n = 0, forces the selected
BUC off line
n = 1, forces the selected
BUC on line
If a BUC is forced
off line when the
alternative BUC in
the redundancy
system is faulty,
the redundancy
system
automatically
switches the nonfaulty BUC back
on line.
Sets the data format of the
RS422/485 and FSK serial
interfaces.
The data format for these
interfaces cannot be set
independently.
This command can only be
used on the RS232 port.
SSIr,w,
p,s,t
r = baud rate (1200, 2400,
4800, 9600, 19200)
w = word length in bits
(7 or 8)
p = parity N/n (none),
E/e (even), O/o (odd)
s = number of stop bits
(1 or 2)
t = RS422/485 bus
terminated or unterminated
(T/t, U/u)
70
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 14:
Set commands (cont.)
Command
Function
Enter... Data required
Set packet
protocol
Sets the packet protocol used SPPn
on the RS422/485 and FSK
serial interfaces.
n = 0, ASCII protocol
n = 1, Codan protocol
n = 2, SAbus protocol
The packet protocols for
these interfaces cannot be set
independently.
n = 3, Comstream protocol
n = 4, NDSatcom protocol
This command can only be
used on the RS232 port.
Set packet
address
Set echo
Sets the packet address.
SADn
The packet address range
depends on the packet
protocol selected (see
page 71, Set packet
protocol).
1 ≤ n ≤ 126, Codan
protocol
49 ≤ n ≤ 111, SAbus
protocol
1 ≤ n ≤ 31, Comstream
protocol
For information on protocols,
contact your Codan
representative.
1 ≤ n ≤ 15, NDSatcom
protocol
SECn
Switches the echoing of
characters on or off in ASCII
protocol mode on the RS232
interface only.
n = 0, disables echoing
n = 1, enables echoing
Echo is always off on the
FSK and RS422/485
interfaces.
Block Up Converter Systems 6700/6900 series User Guide
71
Setting up and operating the BUC system
Table 15:
Command
Output commands
Function
Enter... Data required
Output power Displays the RF power
output
output of the BUC in dBm.
OPO
None
OBP
None
If the output power is less
than the lower limit, 0.0 dBm
is displayed.
If the output power is greater
than the upper limit,
99.9 dBm is displayed.
Output burst Displays the current,
powers
minimum and maximum
burst output powers of the
BUC in dBm.
If the burst power is less than
the lower limit, 0.0 dBm is
displayed.
If the burst power is greater
than the upper limit,
99.9 dBm is displayed.
72
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 16:
Command
View commands
Function
View system Displays the status and
status
parameter settings of the
BUC.
Enter... Data required
VSS
None
View
operational
data
Displays the operational data VOD
of the BUC.
None
View fault
status
VFS
Displays the fault status of
the BUC. In a
transmit/receive redundancy
system it also displays the
fault status of the LNB and
the redundancy controller. It
displays both current faults
and latched faults (that is,
faults that have previously
occurred but may have
cleared).
None
VID
View identity Displays the identification
and configuration data of the
and
configuration BUC.
data
None
View limit
data
Displays the frequency and
power ranges for the BUC.
VLD
None
View
Displays the serial interface
protocol data protocol information.
VPD
None
View build
Displays the build standard
standard data information of the BUC.
VBS
None
Block Up Converter Systems 6700/6900 series User Guide
73
Setting up and operating the BUC system
Table 17:
Reset commands
Command
Function
Enter... Data required
Reset
Resets the BUC settings to the settings RST
at powerup (that is, it has the same
effect as switching the power off then
on again). The maximum and minimum
readings for the burst mode power are
cleared, the LO synthesiser is reloaded
and, if the transmit default state is set to
off, the PA of the BUC is switched off.
Reset latched Clears all latched faults except those
faults
that are still current.
Reset to
default
values
None
RLF
None
Resets the parameters that are changed RDV
via the Set commands to their factory
default settings.
None
NOTE
If you have a C-Band BUC,
you should switch off the
carrier at the modem before
using this command. This
prevents transmission on an
undesired frequency. When
you have reset the LO
frequency, switch
transmission on.
The default settings are:
transmit
on (for RS232,
RS422/485 and
FSK)
RF compensation
frequency
0 MHz
IF compensation
frequency
0 MHz
transmit attenuator 12 dB
74
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Table 17:
Reset commands (cont.)
Command
Function
Enter... Data required
Reset to
default
values
(cont.)
output power
threshold
0 dBm (off)
burst mode power
threshold
0 dBm (off)
LO frequency
C-Band:
7375 MHz
Ku-Band:
15450 MHz
transmit default
PA returns to
transmit state prior
to powerdown
redundant mode
non-redundant
mode
serial interface
9600 baud
8 bits
no parity
1 stop bit
unterminated
RS422/485 bus
packet protocol
NDSatcom
protocol
packet address
1 for Codan
49 for SAbus
1 for Comstream
1 for NDSatcom
echo
on
Block Up Converter Systems 6700/6900 series User Guide
75
Setting up and operating the BUC system
Switching the redundancy system on and
off
When you power up the redundancy controller, the
redundancy switching system resumes operation using the
current state of the switches.
You can switch off the redundancy switching system at any
time by simply switching off the redundancy controller at the
AC mains supply. In some BUC systems, the BUCs are also
powered down.
Checking the operation of the LED
indicators and controls
The redundancy controller has 18 indicators on the internal
control panel (see Figure 9 on page 18 and Table 12 on
page 60).
Switching between streams
The redundancy controller enables automatic and manual
switching of streams.
The redundancy controller automatically switches streams
when it receives an alarm from the on-line stream. The
redundancy controller always switches transmit and receive
paths together.
You can manually force the system to switch between
Stream 1 and Stream 2.
76
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
Operating the redundancy system
If you are not using the contact closure inputs on the
Auxiliary I/O connector, the redundancy controller runs
automatically. You can manually switch streams by setting the
Online state of a BUC using a Hand-held Controller 6560 or
a PC connected to the BUC 1 Serial or BUC 2 Serial
connectors, or a Remote Controller 6570 connected to the
Auxiliary I/O connector.
If you want to exert external control via the contact closures
on the Auxiliary I/O connector (see Figure 14 on page 52)
you must:
1
Ground pin J.
This enables remote control.
1
Select Manual Mode by grounding pin N, or select Auto
Mode by not grounding pin N.
1
If Manual Mode was selected in the previous step, then
you may select Stream 2 by grounding pin G, or select
Stream 1 by not grounding pin G.
NOTE
External stream selection in Manual Mode
is independent of any faults.
Block Up Converter Systems 6700/6900 series User Guide
77
Setting up and operating the BUC system
Controlling the redundancy system
For correct operation of the redundancy system, both BUCs
must be switched on.
To switch on the BUCs:
1
Switch on the modem, and if you have installed an
externally-powered BUC system, switch on the power to
the BUC.
The standby state of the off-line BUC is dependent on how the
Redundancy mode is set. The off-line BUC can be set to two
states:
•
power amplifier on (hot standby system)
•
power amplifier off (warm standby system)
NOTE
In a high-power BUC system, the high-power
SSPA is always activated.
Hot standby
In hot standby, the power amplifier of each BUC is activated
ready for immediate use. A hot standby system has greater
power consumption than any other redundancy system
configuration.
To set the BUCs to operate in hot standby:
1
78
Set the Redundancy mode to Hot standby using a
Hand-held Controller 6560, a Remote Controller 6570,
or serial commands on a PC running terminal-emulating
software.
Block Up Converter Systems 6700/6900 series User Guide
Setting up and operating the BUC system
NOTE
Codan recommends that you set the
Redundancy mode of both BUCs to
Hot standby. This keeps the off-line
stream in hot standby ready for immediate
operation. It also enables detection of
faults in the power amplifier of the off-line
BUC through the normal fault detection
system, or via the transmit power alarm
threshold facility.
Warm standby
In warm standby, only the power amplifier of the on-line BUC
is activated. This provides a lower power consumption than
the hot standby system. The power amplifier of the off-line
BUC is automatically activated when the stream switches to
on line.
To set the BUCs to operate in warm standby:
1
Set the Redundancy mode to Warm standby using
a Hand-held Controller 6560, a Remote Controller 6570,
or serial commands on a PC running terminal-emulating
software.
Block Up Converter Systems 6700/6900 series User Guide
79
Setting up and operating the BUC system
This page has been left blank intentionally.
80
Block Up Converter Systems 6700/6900 series User Guide
4
Maintenance and fault
finding
CODAN
This section contains the following topics:
Precautions (82)
If technical assistance is required... (84)
Finding faults in the BUC system (85)
Finding faults in the redundancy switching equipment (100)
Finding faults in the remote controller (109)
Block Up Converter Systems 6700/6900 series User Guide
81
Maintenance and fault finding
Precautions
Connections to power supplies
In general, exposed connector pins do not carry DC supply
voltages.
WARNING
Care should be taken at all times to avoid short
circuiting connector pins.
Servicing requirements
If you find that any module is faulty, contact your Codan
representative or Codan customer service staff. Before
returning goods to Codan you must obtain an RMA to
authorise the return of your goods.
Do not attempt to repair the module as you may
WARNING cause further faults and void the manufacturer’s
warranty.
RF waveguide switches
Handle all RF waveguide switches with care.
They are easily damaged.
WARNING
It is critical to weatherproof waveguide and
control joints for long-term switch reliability.
The RF waveguide switch is a precision
microwave electromechanical assembly. Do not
attempt to repair it yourself. Return all faulty RF
waveguide switches to Codan for repair.
82
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Fuses and overcurrent protection in the Redundancy
Controller 6586
Table 18 lists the types of fuses on the control panel of the
redundancy controller and the device protected. For
information on changing fuses see page 102, Replacing fuses
in the redundancy controller.
Table 18:
Fuses in the redundancy controller
Label
Type
Protects...
BUC 1/BUC 2
Delay 20 × 5 mm, 5 A
BUC 1/BUC 2
LNB 1/LNB 2
Delay 20 × 5 mm, 1 A
LNB 1/LNB 2
Remote Controller
Delay 20 × 5 mm, 250 mA Remote Controller 6570
NOTE
LNB fuses are fitted, but are not used in
transmit-only systems.
Block Up Converter Systems 6700/6900 series User Guide
83
Maintenance and fault finding
If technical assistance is required...
If the fault diagnosis guidelines do not locate the faulty
module or cable, or if further technical assistance is required
for any other reason, please refer to the contact details
supplied with the equipment. These details are also available
on the internet at www.codan.com.au. In the Satellite
Communications section, click on Product Support.
Outside of normal office hours, Codan has Customer Service
Engineers on call to provide emergency technical assistance.
They will either answer your call immediately or return your
call as soon as possible.
If you are connected to a voice mail system when you call,
please follow the instructions carefully, that is, leave your
name and contact phone number (including the country code),
then a brief, clear description of your problem.
84
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Finding faults in the BUC system
The fault finding information provided in this section is
designed to locate faulty modules and cables, and to determine
if correct operating procedures have been followed. Faults are
indicated by the LEDs on the BUC (see Table 11 on page 59).
If a fault is indicated on the BUC it is recommended that you
check the cables and the cable connections.
Using the BUC fault diagnosis charts
The tests indicated in the diagnosis charts are at the end of this
section. When an ‘*’ appears in a diagnosis chart, it indicates
that you are to refer to the relevant test.
You should be able to locate simple faults with minimal test
equipment. A terminal or a computer emulating a terminal is
required for checking the BUC. The most effective technique
when dealing with complex faults, or if a terminal is not
available, is to substitute modules.
CAUTION
During fault finding or performance testing,
disconnect the transmit IF signal and/or
terminate the BUC output into a suitably-rated
dummy load. This ensures that unwanted
signals are not transmitted.
You can commence fault finding using the:
•
Main BUC fault diagnosis chart (Figure 15 on page 86)
•
LNB fault diagnosis chart (Figure 25 on page 96)
NOTE
The following flow charts assume the BUC is in
non-redundant mode. If the BUC is set to either
of the two redundancy modes and is not
installed in a redundancy system, LNB and
redundancy controller faults are permanently
indicated and cannot be cleared.
Block Up Converter Systems 6700/6900 series User Guide
85
Maintenance and fault finding
Figure 15:
Main BUC fault diagnosis chart
Main BUC fault
diagnosis chart
Is the
PWR LED on the
BUC green?
No
See BUC fault
diagnosis chart 1.
Yes
Is the
FLT LED on the
BUC constant
red?*
Yes
See BUC fault
diagnosis chart 2.
Yes
See BUC fault
diagnosis chart 6.
* The FLT LED on earlierversion BUCs may flash red
to indicate the presence of
latched faults. Latched faults
are reset using the RLF
command.
No
Is the
Tx LED on the
BUC yellow?
No
See BUC fault
diagnosis chart 7.
86
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Figure 16: BUC fault diagnosis chart 1
BUC fault
diagnosis chart 1
Is
BUC externallypowered, or
powered via IF
cable?
Externally
powered
Check voltage on
power connector
(Test B)*.
OK?
* Refer to test
procedures
No
Check cable,
AC mains and circuit
breakers.
IF cable
Yes
BUC faulty.
Refer to Codan.
Is
IF power supply
being used?
No
Check for DC power at
both ends of the Tx IF
cable (Test A)*.
Yes
Check for DC power at
the output of the IF
power supply and the
BUC end of the Tx IF
cable (Test A)*.
OK?
Yes
No
OK?
No
Modem or cable
faulty. Replace
as required.
Yes
Block Up Converter Systems 6700/6900 series User Guide
87
Maintenance and fault finding
Figure 17:
BUC fault diagnosis chart 2
BUC fault
diagnosis chart 2
Check faults using
VFS command.
Is
Tx Power
Alarm
OK?
No
Check the IF level
(Test D)* and the
output power alarm
threshold and adjust
as required.
No
Is
BUC Temp
OK?
Reset latched
faults using RLF
command.
Yes
Does
BUC have
a fan?
88
Yes
Yes
See BUC fault
diagnosis chart 3.
See BUC fault
diagnosis chart 4.
No
Wait for BUC to cool
down. Ensure air flow
around BUC is not
restricted.
* Refer to test
procedures
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Figure 18: BUC fault diagnosis chart 3
BUC fault
diagnosis chart 3
Is
there a
fan fault?
Yes
See BUC fan fault
diagnosis chart 1.
Yes
See BUC fault
diagnosis chart 4.
No
Is
BUC Temp
OK?
No
See BUC fan fault
diagnosis chart 1.
Block Up Converter Systems 6700/6900 series User Guide
89
Maintenance and fault finding
Figure 19:
BUC fault diagnosis chart 4
BUC fault
diagnosis chart 4
Is PA
OK?
See BUC fault
diagnosis chart 5.
Yes
No
Switch off BUC PA
using STO0
command.
Reset BUC using RST
command. Reset
latched faults using
RLF command.
Switch on BUC PA
using STO1
command.
Is
FLT LED
red and PA
showing a
fault?
Yes
BUC faulty.
Refer to Codan.
No
BUC OK.
Monitor for recurrence
of fault.
90
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Figure 20: BUC fault diagnosis chart 5
BUC fault
diagnosis chart 5
Is LO
OK?
Reset latched faults
using RLF command.
Monitor for recurrence
of fault.
Yes
No
Does BUC
have an internal
10 MHz
reference?
BUC faulty.
Refer to Codan.
Yes
No
Check for 10 MHz at
both ends of the Tx IF
cable (Test C)*.
OK?
Modem, external
10 MHz reference
source, or cable faulty.
Replace as required.
No
Yes
Reset BUC using RST
command. Reset
latched faults using
RLF command.
Is
FLT LED red and
LO showing a
fault?
Yes
BUC faulty.
Refer to Codan.
No
BUC OK.
Monitor for recurrence
of fault.
Block Up Converter Systems 6700/6900 series User Guide
* Refer to test
procedures
91
Maintenance and fault finding
Figure 21:
BUC fault diagnosis chart 6
BUC fault
diagnosis chart 6
Check for presence of
Tx IF from modem at
both ends of the Tx IF
cable (Test D)*.
OK?
No
Modem, any other
device on IF cable, or
cable faulty. Replace
as required.
Yes
Is the
transmit
attenuator setting
correct?
No
Set the correct
transmit attenuator
setting using STA
command.
Yes
BUC faulty.
Refer to Codan.
92
* Refer to test
procedures
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Figure 22: BUC fault diagnosis chart 7
BUC fault
diagnosis chart 7
Switch the BUC PA on
using STO1
command.
Is the
Tx LED
yellow?
Yes
BUC OK.
No
BUC faulty.
Refer to Codan.
No
Reset the setting to
default values using
RDV command.
Is the
Tx LED
yellow?
Yes
Set all BUC settings
changed by RDV
command.
BUC OK.
Block Up Converter Systems 6700/6900 series User Guide
93
Maintenance and fault finding
Figure 23:
BUC fan fault diagnosis chart 1
BUC fan fault
diagnosis chart 1
Reset BUC using RST
and RLF commands.
Check fan fault using
VFS command.
Is fan fault
still present?
No
Fan operation
normal.
Yes
Are fan(s)
running?
No
See BUC fan fault
diagnosis chart 2.
Yes
BUC faulty.
Refer to Codan.
94
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Figure 24: BUC fan fault diagnosis chart 2
BUC fan fault
diagnosis chart 2
Check for obstruction
or seized bearings on
stationary fan(s).
OK?
No
Repair/replace
fans as
necessary.
Yes
Fan faulty.
Repair/replace
fans as
necessary.
Yes
Check for DC power at
the fan (Test E)*.
OK?
No
BUC faulty.
Refer to Codan.
Block Up Converter Systems 6700/6900 series User Guide
* Refer to test
procedures
95
Maintenance and fault finding
Figure 25:
LNB fault diagnosis chart
LNB fault
diagnosis chart
Disconnect LNB.
Check for +15 V DC at
both ends of the Rx IF
cable (Test F)*.
OK?
Modem, external
LNB power supply, or
cable faulty. Replace
as required.
No
Yes
Does LNB
have an
internal 10 MHz
reference?
Yes
LNB faulty.
Replace LNB or
refer to Codan.
No
Check 10 MHz at both
ends of the Rx IF
cable (Test C)*.
OK?
No
Modem, external
10 MHz reference
source, or cable faulty.
Replace as required.
Yes
LNB faulty.
Replace LNB or
refer to Codan.
96
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Test procedures
Use the following tests in conjunction with the fault finding
diagnosis charts.
Table 19:
Test A
Procedure
Comment
Measure the DC voltage at both ends of For +24 V BUCs, the DC voltage should
be +19 to +35 V DC.
the transmit IF cable.
Connect positive to the centre pin and
negative to ground (to the screen).
Table 20:
For +48 V BUCs, the DC voltage should
be +42 to +60 V DC.
Test B
Procedure
Comment
Measure the voltage on the connector
that plugs into the BUC.
For AC-powered BUCs, the measured
AC mains voltage must be between 94
and 275 V AC.
Care needs to be taken
For DC-powered BUCs, the measured
when performing this
WARNING measurement as a severe voltage range should be as stated in
Test A (Table 19 on page 97).
electric shock and
personal injury may result.
For pinouts of the AC INPUT connector
see Table 8 on page 31.
Block Up Converter Systems 6700/6900 series User Guide
97
Maintenance and fault finding
Table 21:
Test C
Procedure
Comment
Measure 10 MHz at both ends of the
The 10 MHz signal level should be –5 to
transmit or receive IF cable as required. +5 dBm.
A DC block may be
required to protect the test
WARNING
equipment from the DC
voltage on the IF cable.
Table 22:
Test D
Procedure
Comment
Measure IF level at both ends of the
transmit IF cable.
The IF signal level should be consistent
with the IF level plan for the BUC.
NOTE
A DC block may be
It is recommended that a
required to protect the test
spectrum analyser is used
to measure the IF level. A WARNING equipment from the
+24/48 V DC on the
power meter may be used
transmit IF cable.
but the reading will be
misleading unless the
10 MHz signal can be
filtered out.
Table 23:
Procedure
Test E
Comment
Measure the DC voltage at the fan feed- Depending on the BUC, the DC voltage
through connections on the BUC,
should usually be either:
positive and negative as marked.
• 9 to 10.2 V DC, or
• 12 V ±1 V DC
Refer to your Codan representative for
exact specifications for your BUC.
98
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Table 24:
Procedure
Test F
Comment
Measure the DC voltage at both ends of The DC voltage should be +15 to
the receive IF cable.
+24 V DC.
Block Up Converter Systems 6700/6900 series User Guide
99
Maintenance and fault finding
Finding faults in the redundancy switching
equipment
A fault in the redundancy switching equipment is likely when
a fault in the on-line BUC or high-power BUC system does
not cause streams to switch, or you cannot manually switch
streams. If this occurs, view the control panel of the
redundancy controller to assess the probable cause of the fault.
The probable faults for the redundancy switching equipment
are:
•
blown fuses
•
inconsistent stream selections, indicated by two BUC
Switch LEDs and two LNB Switch LEDs illuminated
green on opposing streams
•
faults in the RF waveguide switches, indicated by four
BUC Switch LEDs and/or four LNB Switch LEDs
being illuminated red
•
faults in the redundancy controller, indicated by the
Redundancy Controller Status LED illuminated
red, following the elimination of blown fuses, and RF
waveguide switch and cable faults
Blown fuses
If the control panel of the redundancy controller indicates that
any fuses are blown, replace the fuses (see page 102,
Replacing fuses in the redundancy controller).
Inconsistent stream selections
During stream selection, an RF waveguide switch may fail to
switch completely between the streams. In this situation, the
BUC Switch or LNB Switch LEDs indicate that one stream
is selected in transmit and the other selected in receive. If this
fault is indicated, continue from page 103, Resolving
inconsistent stream selections.
100
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Faults in the RF waveguide switches
Faults in the RF waveguide switches are caused inside the
switches or in the switch cables. Such faults are likely if:
•
the BUC Switch or LNB Switch LEDs on the control
panel of the redundancy controller are illuminated red,
which indicates inconsistencies from the RF waveguide
switch tell-back contacts
•
there is a loss of the transmit or receive signal
If these faults are indicated, continue from page 103, Finding
faults in an RF waveguide switch.
Faults in the redundancy controller
Faults in the redundancy controller are caused by faults in the
controller unit itself or the cables connected to the controller.
These types of faults are indicated by the failure of the
redundancy switching equipment when an RF waveguide
switch fault is unlikely. To determine where the fault may be,
continue from page 107, Finding faults in the redundancy
controller.
NOTE
In transmit-only systems, the LNB Switch
LEDs are not operational.
NOTE
In C-Band transmit/receive systems that use
combined RF waveguide/coaxial switches, the
BUC Switch LEDs are not operational.
Block Up Converter Systems 6700/6900 series User Guide
101
Maintenance and fault finding
Replacing fuses in the redundancy controller
Make sure that the AC mains power is switched
WARNING off before replacing fuses or disconnecting
power cables.
To replace a blown fuse:
1
1
Switch off the redundancy controller at the AC mains.
1
Replace the blown fuse on the control panel of the
redundancy controller.
1
Switch on the AC mains supply to the redundancy
controller.
1
If the fuse blows again, the redundancy controller is
faulty. Contact your Codan representative for assistance.
1
If the fuse does not blow, reconnect all cables one by
one.
Disconnect all the cables from the redundancy controller
except for the power cables.
If the fuse blows, the last unit connected, or its cable, is
faulty.
If the fuse does not blow after reconnecting all cables,
the original fuse may have blown because of a temporary
power supply surge.
1
102
If a problem persists, contact your Codan representative
for assistance.
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Resolving inconsistent stream selections
To resolve inconsistent stream selections:
1
Use serial commands on a PC running terminalemulating software, a Hand-held Controller 6560, or a
Remote Controller 6570 to switch streams remotely (see
page 76, Switching between streams).
1
Switch streams several times to ensure that the switches
are operating correctly in both streams.
1
If the inconsistent stream selections persist, continue
below at Finding faults in an RF waveguide switch.
Finding faults in an RF waveguide switch
The redundancy controller monitors the tell-back contacts in
the RF waveguide switch.
If Stream 1 is on line:
•
position 1 tell-back contact should be closed to the
tell-back common contact
•
position 2 tell-back contact should be open
The opposite should be true when Stream 2 is on line.
If the redundancy controller detects that either tell-back
contact is set incorrectly, the BUC Switch or LNB Switch
LEDs illuminate red.
RF waveguide switch faults might be caused by:
•
an open or short in the control cable for the switch
•
a jammed switch or switch that does not rotate through
its full 90° arc
•
a burnt-out coil in the switch
•
faulty tell-back contacts
Use Figure 26 on page 104 to check for faults in an RF
waveguide switch.
Block Up Converter Systems 6700/6900 series User Guide
103
Maintenance and fault finding
Figure 26:
RF waveguide switch fault diagnosis chart
RF waveguide switch
fault diagnosis chart
Disconnect cable from switch.
Select position 1 by manually
rotating actuator in switch.
Are the
resistances and tell-back
contacts consistent with
Table 25?
No
Switch faulty.
Replace switch.
No
Switch faulty.
Replace switch.
Yes
Repeat measurements
at 6586 end of cable.
Select position 2 by manually
rotating actuator in switch.
Are the
resistances and tell-back
contacts consistent with
Table 25?
Yes
Reconnect cable to switch.
Disconnect cable from 6586.
What
colour are the
BUC Switch and
LNB Switch*
LEDs?
Green
Switch fault
resolved.
Red
6586 faulty.
104
* LNB Switch LEDs
are not operational in
transmit-only systems
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Checking the resistance of an RF waveguide switch
To check the resistance of an RF waveguide switch:
1
Disconnect the control cable from the RF waveguide
switch.
1
Use a multimeter to check the resistance of the coils and
tell-back contacts at the connector on the switch.
Table 25 shows the expected results at RF waveguide
switch position 1 and position 2.
NOTE
To manually change a switch position,
remove the cover on the actuator of the
switch, then rotate the actuator.
NOTE
The pin numbers in Table 25 apply to the
connectors at both ends of the cable
connecting the RF waveguide switch to the
redundancy controller.
Table 25: Resistance of coils when the RF waveguide
switch is in positions 1 and 2
RF waveguide
switch
Resistance of pin A
(coil 1) to pin B
(common)
Resistance of pin C
(coil 2) to pin B
(common)
Tell-back
contact
Position 1
(coil 1 open
circuit)
Very high
100 Ω (WR137, WR75)
24 Ω (WR229)
D–E closed
F–E open
Position 2
(coil 2 open
circuit)
100 Ω (WR137, WR75)
24 Ω (WR229)
Very high
D–E open
F–E closed
NOTE
The resistance of pin C to pin B for position 1 of
the RF waveguide switch is not applicable to
transmit-only systems.
Block Up Converter Systems 6700/6900 series User Guide
105
Maintenance and fault finding
If both coils of an RF waveguide switch have high
resistance, it is possible that the switch has burnt out. If
the resistance of the coils is within the range, the switch
may be jammed.
Checking a jammed RF waveguide switch
To check an RF waveguide switch that appears to be jammed:
1
Remove the RF waveguide switch from the waveguide
components and check for foreign material.
1
1
Reconnect the control cable to the RF waveguide switch.
1
If the RF waveguide switch does not move, remove the
control cable and the actuator cover from the RF
waveguide switch.
Try to manually operate the RF waveguide switch using
a Remote Controller 6570 or Hand-held Controller 6560
while someone observes the internal waveguide
mechanism (see page 76, Switching between streams).
Try physically rotating the RF waveguide switch by
hand.
106
1
If the RF waveguide switch functions correctly, reinstall
the RF waveguide switch to the waveguide components.
1
If the RF waveguide switch fails to operate correctly,
bypass the switch by connecting the LNB or BUC
directly to the receive port or transmit port of the antenna
feed respectively.
1
Return the RF waveguide switch to Codan for repair.
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Finding faults in the redundancy controller
To check for faults in the redundancy controller:
1
In a BUC system, check the voltage between the centre
pin and body of the Tx IF Output 1 and Tx IF
Output 2 connectors.
WARNING Do not short circuit the outputs.
1
If 36 to 60 V DC is not present, check the fuses.
If the fuses have not blown, the power supply inside the
redundancy controller is faulty. Contact your Codan
representative for assistance.
Disconnecting a faulty BUC
If you determine that a BUC is faulty and you cannot rectify
the fault, you may need to remove the faulty BUC from the
system so that it can be repaired.
To remove a faulty BUC while maintaining a communication
path:
1
Disconnect the cable from the BUC 1 Control or
BUC 2 Control connector on the redundancy
controller, as required.
1
If you are removing an externally-powered BUC from
the system, switch off the power supply to the BUC.
1
Disconnect the cable from the Tx IF Output 1 or Tx IF
Output 2 connector on the redundancy controller, as
required.
This will not interrupt traffic. The redundancy controller
will continue to run the on-line BUC.
1
Disconnect any unused cables from the redundancy
controller and fit the supplied dust caps.
Block Up Converter Systems 6700/6900 series User Guide
107
Maintenance and fault finding
Reverting to a single-BUC earth station
If it is necessary to remove the redundancy controller from the
system because it is faulty, you can restore communications by
reverting to a basic, single-BUC earth station. You can either
leave the RF waveguide switches in place or remove them.
To revert to a single-BUC earth station:
1
1
Switch off the redundancy controller.
1
At the redundancy controller, unplug the two IF coaxial
cables that connect to the modem or other equipment.
Reconnect these cables directly to the on-line BUC.
Remove the control and IF coaxial cables between the
redundancy controller, BUCs and LNBs (if used).
If you are unsure of the position of the RF waveguide
switches, use a multimeter to check the tell-back contacts
at the control connector for the RF waveguide switch
(see Table 26).
Table 26:
and 2
Tell-back contacts for switch positions 1
Switch position 1
Switch position 2
D–E closed
D–E open
F–E open
F–E closed
1
Remove any remote interface cable from the
Auxiliary I/O connector on the redundancy controller.
1
If you need to remove a faulty RF waveguide switch,
connect the BUC or LNB directly to the antenna feed.
1
Seal all N-type connections with self-amalgamating tape.
CAUTION
108
Ensure all joints are completely
weatherproof.
Block Up Converter Systems 6700/6900 series User Guide
Maintenance and fault finding
Finding faults in the remote controller
The remote controller or its associated cable is faulty if the
LEDs on the remote controller are not illuminated, or actions
taken on the remote controller are not reflected in the
redundancy system.
Checking for supply faults
Use Figure 27 on page 110 to check for supply faults to the
remote controller.
Block Up Converter Systems 6700/6900 series User Guide
109
Maintenance and fault finding
Figure 27:
chart
Remote controller supply fault diagnosis
Remote controller
supply fault
diagnosis chart
Check the Remote
Controller fuse on
6586.
Fuse
OK?
Replace fuse.
No
Yes
Is there
+12 V between
pin 2 and pin 1 on
Auxiliary I/O
cable
assembly?
Yes
Remote controller
faulty.
No
Auxiliary I/O
cable assembly
faulty.
No
Is there
+12 V between
pin U and pin D at
Auxiliary I/O
connector on
6586?
Yes
6586 faulty.
Refer to Codan.
110
Block Up Converter Systems 6700/6900 series User Guide
Appendix A—BUC model and
redundancy system numbers
CODAN
BUC model numbers
The model number of your BUC indicates various options
available in your BUC.
Figure 28: Segments of the BUC model number
Table 27:
Definition of the BUC model number
Option
Description
Code
Model type
C-Band
67
Ku-Band
69
Output power
PP
Output power
Special vairants
CE compliance
Power connector
Power supply
Frequency band
RF output type
Output power
Model type
NNPP-X/Y-AA/BB-GG-ZZ
For example:
PP is represented as 10 for a 10 W BUC
PP is represented as 12H for a 120 W BUC
RF output type
N-type
N
Waveguide
W
Block Up Converter Systems 6700/6900 series User Guide
111
BUC model and redundancy system numbers
Table 27:
Definition of the BUC model number (cont.)
Option
Description
Code
Frequency band
Standard: 5.850 to 6.425 GHz for C-Band
S
14.0 to 14.5 GHz for Ku-Band
Extended: 5.850 to 6.725 GHz for C-Band
E
13.75 to 14.50 GHz for Ku-Band
Power supply
Power connector
CE certification
Special variants
24 V DC
24
48 V DC
48
AC
AC
IF N-type connector
IF
External power connector
EX
CE-certified
CE
Not CE-certified
Segment
omitted
Codes allocated as required
For example, the model number 6725-W/E-AC/EX-CE
represents a C-Band 25 W MBUC with waveguide output
using the Extended frequency band. It is AC powered via an
external power connector, and is CE-certified. It has no special
variants.
112
Block Up Converter Systems 6700/6900 series User Guide
BUC model and redundancy system numbers
Redundancy system numbers
The number of your redundancy system indicates various
options available in your system.
Figure 29: Segments of the redundancy system
number
Table 28:
System type
BUC model and
power group
BUC output
connector
Frequency band
Redundancy
controller
6586-AA/B-CC-DD
Definition of the redundancy system number
Option
Description
Code
Frequency band
C-Band
C
Ku-Band
Ku
N-type coaxial (C-Band only)
N
Waveguide (C-Band and Ku-Band)
W
BUC output
connector
Block Up Converter Systems 6700/6900 series User Guide
113
BUC model and redundancy system numbers
Table 28:
(cont.)
Definition of the redundancy system number
Option
Description
BUC model and
power group
LBUC
C-Band:
Code
5 W, 10 W, 20 W
L1
Ku-Band: 4 W, 8 W, 16 W
MBUC
C-Band:
25 W, 40 W
M1
Ku-Band: 16 W
C-Band:
60 W
M2
Ku-Band: 25 W
HBUC
C-Band:
120 W
H1
Ku-Band: 40 W
System type
Transmit-only (BUC)
TO
Transmit/receive (BUC & LNB)
TR
For example, the model number 6586-C/W-M2-TO represents
a C-Band transmit-only redundancy system using 60 W
MBUCs with waveguide output.
114
Block Up Converter Systems 6700/6900 series User Guide
Appendix B—Example outputs
for the View commands
NOTE
CODAN
These outputs show example data only. The data
displayed can vary between BUC systems and
firmware versions.
View system status
The figures in brackets are the parameter values enabled for
the Set commands that were used to achieve the settings
displayed.
In a system without redundancy:
NOTE
• the BUC is always On Line; this setting
cannot be changed
• the Redundant Mode must always be set to
non-redundant (0)
-----------------------System Status------------------------------PA State
Off
Transmit Atten
4
Transmit On (RS232) On (1)
Tx Alarm Thresh
0.0
Transmit On (RS485) Off (0)
Burst Pwr Thresh
19.0
Transmit On (FSK)
On (1)
Serial I/face
9600,8,N,1,T
Transmit Default
Off (0)
Packet Protocol
Codan (1)
Compensation Freq
0
Packet Address
126
IF Comp Freq
0
Red'cy -Mode
Non (0)
LO Freq
7375
-On/Off Line On (1)
-----------------------------------------------------------------
View operational data
---------------------Operational Data---------------------Output Power
0.0
Burst Power
0.0
Min Burst Power
0.0
Max Burst Power
99.9
Temperature(C)
31
----------------------------------------------------------
Block Up Converter Systems 6700/6900 series User Guide
115
Example outputs for the View commands
View fault status
-------------Fault Status------------Current
Latched
PA
OK
OK
Fan
OK
OK
Tx Power Alarm
OK
OK
BUC Temp
OK
OK
LO
OK
OK
Internal
OK
OK
LNB
Red'cy Controller
--------------------------------------
NOTE
If there is no fan in the BUC, the current and
latched status for the fan shows a dash.
View identity and configuration data
--------------------------Identity Data---------------------------Model No
6704/48
Serial No
3232676a0005
Firmware P/No
90-20621-001 Firmware Version
1.06
-------------------------------------------------------------------
View limit data
The data displayed depends on the model of the BUC and the
current LO setting.
-----------------------Limit Data--------------------------Min Tx IF Freq
950
Max Tx IF Freq
1525
Min Tx RF Freq
5850
Max Tx RF Freq
6425
LO1 Freq
7300
LO2 Freq
7600
LO3 Freq
7375
LO4 Freq
7675
Min Power Meter
19.0
Max Power Meter
36.0
-----------------------------------------------------------
116
Block Up Converter Systems 6700/6900 series User Guide
Example outputs for the View commands
View protocol data
-----------------------Protocol Data-------------------Protocol 0
ASCII
Protocol 1
Codan
Address Range 1..126
Protocol 2
SAbus
Address Range 49..111
Protocol 3
Comstream
Address Range 1..31
Protocol 4
NDSatcom
Address Range 1..15
-------------------------------------------------------
View build standard data
-----------Build Standard ------------H/W Std
S/W Std
M&C PCB
1
1
RF PCB
1
1
LO PCB
1
1
Pwr PCB
1
---------------------------------------
Block Up Converter Systems 6700/6900 series User Guide
117
Example outputs for the View commands
This page has been left blank intentionally.
118
Block Up Converter Systems 6700/6900 series User Guide
Appendix C—Compliance
CODAN
This section contains the following topics:
Introduction (120)
European R&TTE Directive (121)
Electromagnetic compatibility and safety notices (123)
Block Up Converter Systems 6700/6900 series User Guide
119
Compliance
Introduction
The Block Up Converter 6700/6900 series is manufactured in
a number of variants. CE-certified versions are marked with
the 0682 , 0682 or
symbols.
This section describes how to ensure the Block Up Converter
6700/6900 series and Redundancy Controller 6586 comply
with the European Electromagnetic Compatibility Directive
89/336/EEC and the European Low Voltage Directive
73/23/EEC as called up in the European R&TTE Directive
1999/5/EC.
120
Block Up Converter Systems 6700/6900 series User Guide
Compliance
European R&TTE Directive
CE-certified versions of the Block Up Converter 6700/6900
series and Redundancy Controller 6586 have been assessed
and comply with the following standards (articles of the
R&TTE Directive):
•
Article 3.1a: EN 60950
•
Article 3.1b: ETSI EN 301 489-1
•
Article 3.1b: ETSI EN 301 489-12
•
Article 3.2: ETSI EN 301 428
•
Article 3.2: ETSI EN 301 443
Compliance with these standards is sufficient to fulfil the
requirements of the R&TTE Directive 1999/5/EC, which
encompasses the following directives:
•
European EMC Directive, 89/336/EEC
•
European Low Voltage Directive, 73/23/EEC with no
lower voltage limit
Product marking and labelling
Any equipment supplied by Codan that satisfies these
requirements is identified by the 0682 , 0682 or
markings on the model label of the product.
Declaration of conformity
The CE declarations of conformity for each specific product
can be made available upon request to Codan or a Codanauthorised supplier.
Block Up Converter Systems 6700/6900 series User Guide
121
Compliance
Protection of the radio spectrum
CAUTION
Some countries may restrict the use of satellite
communications equipment on certain
frequency bands or require such equipment to
be licensed. It is the user’s responsibility to
check the specific requirements with the
appropriate communications authorities.
It is the responsibility of the user to ensure any modem used in
conjunction with the Block Up Converter 6700/6900 series
and Redundancy Controller 6586 complies with EN 301 428
or EN 301 443 so that CE-certification with respect to radiated
spurious signals is maintained. If necessary, contact Codan for
more information.
To set up the BUC for CE-certified operation you must:
1
Enter the STD0 command.
This sets the default transmit state on powerup to Off.
1
Enter the STO1 command to activate the BUC.
Health requirements (human exposure to
electromagnetic fields)
The Block Up Converter 6700/6900 series and Redundancy
Controller 6586 have been assessed against the health
requirements in article 3.1a of the R&TTE Directive
(1999/5/EC) complying with VDE0848, ICNIRP and FCC
health requirements.
The Redundancy Controller 6586 is non-transmitting ancillary
equipment according to ETSI EN 301 428 and ETSI EN 301
443, and does not cause or increase the risk of human
exposure to electromagnetic fields.
122
Block Up Converter Systems 6700/6900 series User Guide
Compliance
Electromagnetic compatibility and safety
notices
Radiation safety
A radiation hazard exists if the BUC is operated
with its RF output unterminated. Do not operate
WARNING
the BUC without a load or termination attached
to the RF output.
Electromagnetic compatibility
To ensure compliance with the EMC Directive is maintained,
you must:
1
Use standard shielded cables supplied from Codan
(where applicable).
1
Ensure the covers for the equipment are fitted correctly.
CAUTION
If it is necessary to remove the covers at any
stage, they must be refitted correctly before
using the equipment.
CAUTION
The dust caps supplied with the Redundancy
Controller 6586 must always be fitted to the
relevant connectors when the connections are
not in use. This enables any electrostatic charge
on service personnel or equipment to discharge
safely via the dust cap prior to connecting a
cable to the port.
Block Up Converter Systems 6700/6900 series User Guide
123
Compliance
Electrical safety
To ensure compliance with the European Low Voltage
Directive is maintained, you must install the Block Up
Converter 6700/6900 series in accordance with the following
safety precautions. These precautions must be checked before
applying power to the BUC.
For DC-powered BUCs, a protective earth
connection must be connected to the protective
WARNING
earth terminal on the BUC (see page 126, Earth
symbols).
For AC-powered BUCs:
• A protective earth connection must be
included in the mains wiring to the BUC (see
page 126, Earth symbols).
• As these BUCs are intended for permanent
connection to the mains supply, a readily
accessible switch or circuit breaker must be
WARNING
incorporated in the mains wiring to enable
easy isolation of the unit.
• The isolating switch must disconnect both
poles simultaneously. However, if you can
positively identify the neutral conductor, you
may have a single-pole isolating device in the
live conductor.
The Redundancy Controller 6586 is intended for permanent
installation and is suitable for Mains Transient Voltages in
Overvoltage Category II (as identified in EN 60950-1 or
AS/NZS 60950-1 Table G.1.).
Touch temperatures at the top of the control panel of the
Redundancy Controller 6586 and the external casing of the
Block Up Converter 6700/6900 series are within allowable
limits of EN 60950-1 and AS/NZS 60950-1, but may become
high, depending on load conditions. The label indicating high
temperature areas is shown in Table 29 on page 125.
124
Block Up Converter Systems 6700/6900 series User Guide
Compliance
Hazardous voltages exist behind the control panel of the
Redundancy Controller 6586 and care should be taken by
service personnel when the panel is removed. The label
indicating that hazardous voltages are present is shown in
Table 29.
Table 29:
Electrical safety symbols
Symbol
Meaning
High touch temperatures may
exist, depending on load
conditions
Hazardous voltages exist
within the unit
A hard-wired permanent protective earth must be connected at
all times to the Redundancy Controller 6586 using the
protective earth terminal provided (see Table 30 on page 126).
Double pole/neutral fusing: For servicing where
the control panel of the Redundancy Controller
WARNING 6586 is removed, disconnect the mains supply
from the redundancy controller by unplugging
the mains supply.
All circuits within the Redundancy Controller 6586 (apart
from AC mains circuits) are earthed SELV circuits, provided
that the protective earth terminal on the redundancy controller
is connected to earth.
Block Up Converter Systems 6700/6900 series User Guide
125
Compliance
Earth symbols
Earth connection points are provided on the Block Up
Converter 6700/6900 series. The symbols shown in Table 30
are used to identify the earths on the equipment.
Table 30:
Earth symbols
Symbol
Meaning
Chassis earth
Protective earth
Warning labels
The labels shown in Table 31 are used to identify potential
hazards on the equipment.
Table 31:
Warning labels
Label
Meaning
Non-ionising radiation may be emitted
WARNING
TERMINATION FOR
OUTPUT ISOLATOR
CONTAINS BERYLLIUM
126
If you intend to process or recycle this
product refer to the current Material
Safety Data Sheet
Block Up Converter Systems 6700/6900 series User Guide
Appendix D—Definitions
CODAN
This section contains the following topics:
Standards and icons (128)
Acronyms and abbreviations (129)
Units (131)
Unit multipliers (132)
About this issue (133)
Block Up Converter Systems 6700/6900 series User Guide
127
Definitions
Standards and icons
The following standards and icons are used in this guide:
128
This typeface
Means...
Bold
a LED or a connector
Bold
a command that you enter or keyboard key
that you press
Courier
a segment of text that is taken directly from
a computer screen
Italics
a cross-reference or text requiring emphasis
This icon
Means...
1
a step within a task
NOTE
the text provided next to this icon may be of
interest to you
CAUTION
your actions may lead to loss of data,
privacy or signal quality
WARNING
your actions may cause harm to yourself or
the equipment
Block Up Converter Systems 6700/6900 series User Guide
Definitions
Acronyms and abbreviations
This term
Means...
AC
alternating current
ASCII
American standard code for information
interchange
BUC
block up converter
DC
direct current
EMC
electromagnetic compatibility
ETSI
European Telecommunications Standards
Institute
FCC
Federal Communications Commission
FLT
fault
FSK
frequency shift keying
H/W
hardware
IF
intermediate frequency
INCIRP
International Commission on Non-Ionising
Radiation Protection
LED
light emitting diode
LNB
low noise block down converter
LO
local oscillator
M/C
monitor and control
MS
military standard
O/P
output
PA
power amplifier
PC
personal computer
Block Up Converter Systems 6700/6900 series User Guide
129
Definitions
130
This term
Means...
PLD
programmable logic device
PWR
power
RF
radio frequency
RMA
return materials authorisation
R&TTE
radio and telecommunications terminal
equipment
Rx
receive
SELV
safety extra low voltage
TDMA
time division multiple access
TRF
transmit reject filter
Tx
transmit
VSAT
very small aperture terminal
Block Up Converter Systems 6700/6900 series User Guide
Definitions
Units
Measurement
Unit
Abbreviation
Attenuation
decibel
dB
Current
ampere
A
Data rate
bits per second
bps
Frequency
hertz
Hz
Impedance
ohm
Ω
Length
metre
m
Power
decibels relative to
1 mW
dBm
Power
watt
W
Temperature
degrees Celsius
°C
Voltage
volt
V
Block Up Converter Systems 6700/6900 series User Guide
131
Definitions
Unit multipliers
NOTE
132
Units are expressed in accordance with ISO
1000:1992 ‘SI units and recommendations for
the use of their multiples and of certain other
units’.
Unit
Name
Multiplier
m
milli
0.001
d
deci
0.1
k
kilo
1000
M
mega
1000000
G
giga
1000000000
Block Up Converter Systems 6700/6900 series User Guide
Definitions
About this issue
This is the first issue of the Block Up Converter Systems
6700/6900 series User Guide. This document provides general
information on the range of Codan L-Band BUCs and the
Redundancy Controller 6586. Other information relating to
BUC systems is covered below in Associated documents and
Associated specifications.
Associated documents
These documents include:
•
handbooks for various ancillary items used with Codan
BUCs
•
type-approval certificates and declarations of conformity
•
specifications for equipment
•
product price lists and part numbers
•
BUC system solutions
Associated specifications
The following specifications associated with the Block Up
Converter 6700/6900 series are available from Codan upon
request:
•
6700/6900 series BUC user serial commands and
responses
•
ASCII Protocol
•
Codan Packet Protocol
•
packet protocols associated with third-party network
management systems
Block Up Converter Systems 6700/6900 series User Guide
133
Definitions
This page has been left blank intentionally.
134
Block Up Converter Systems 6700/6900 series User Guide
Index
A
Auxiliary I/O interface
redundancy controller 22, 51, 52
relay contacts 51
B
BUC
control 78
disconnecting 107
fault finding 86
frequency conversion plans 7
installation 28
introduction 4
LED indicators 59
monitoring 21
overview 7
power supply 13
reverting to single-BUC operation 108
serial interface 50
single 108
switching on 58
system configuration 5
transmit frequency bands 7
C
cables
cable loss specification 32
cable screening specification 33
control 48
DC loop resistance specification 33
fault finding 107
IF coaxial 48
IF levels 34
installing
control 48
power 47
lengths 33
power 47
recommendations for IF coaxial cables 32
C-Band
frequency conversion plan 8
transmit frequency band 7
CE-certified operation 65, 69, 122
CODAN
combined RF waveguide/coaxial switch
installing 45
compliance 119
electromagnetic compatibility and safety
notices 123
earth symbols 126
electrical safety 124
electromagnetic compatibility 123
warning labels 126
European R&TTE Directive 121
declaration of conformity 121
health requirements 122
labelling 121
protection of radio spectrum 122
connectors 19
E
electromagnetic compatibility and safety notices
compliance
earth symbols 126
electrical safety 124
electromagnetic compatibility 123
warning labels 126
European R&TTE Directive
compliance 121
declaration of conformity 121
health requirements 122
labelling 121
protection of radio spectrum 122
F
fault finding 85
BUC 86
cables 107
inconsistent stream selections 103
LNB 96
redundancy controller 107
redundancy switching system 100
remote controller 109
RF waveguide switch 101, 103
technical assistance 84
test procedures 97
Block Up Converter Systems 6700/6900 series User Guide
Index-1
Index
faults
monitoring 21
redundancy controller 101
frequencies
C-Band transmit frequency band 7
Ku-Band transmit frequency bands 7
frequency conversion plans 7
C-Band 8
Ku-Band 11
FSK interface 38
fuse 83
protection 83
replacing 102
H
L
LED indicators
description 18
on BUC 59
on redundancy controller 18
operation 76
LNB
C-Band frequency band 15
connecting to the redundancy controller 49
fault finding 96
frequency band options 15
interface 29
Ku-Band frequency bands 15
overview 15
M
Help commands 64
help 64
help for Output commands 64
help for Reset commands 64
help for Set commands 64
help for View commands 64
hot standby 78
maintenance 82
monitor and control interface 40, 62
mounting
redundancy controller 42
O
I
IF coaxial cables
connecting to the BUC 48
connecting to the modem or other equipment
48
IF levels 34
inconsistent stream selections
fault finding 103
installation 28
cables
control 48
power 47
combined RF waveguide/coaxial switch 45
LNB 49
receive RF waveguide switch 44
transmit RF waveguide switch 42
interface
Auxiliary I/O 22
operation
initial setup 53
single BUC 108
Output commands 72
output burst powers command 72
output power output command 72
P
power
switch on 53
power supply
BUC 13
connection precautions 82
redundancy controller 21
R
radiation safety 123
K
Ku-Band
frequency conversion plan 11
transmit frequency bands 7
Index-2
Block Up Converter Systems 6700/6900 series User Guide
Index
redundancy controller
Auxiliary I/O interface 22, 51, 52
description 17
fault finding 107
fault monitoring 21
faults 101
LED indicators 18
mounting 42
power supply 21
switches 19
redundancy switching system
control 17
fault finding 100
operating 77
redundancy controller 17
remote controller 16
setting up 53
switching off 76
switching on 76
unpacking 28
relay contacts
Auxiliary I/O interface 51
remote controller 16
connecting 55
fault finding 109
Reset commands 74
reset command 74
reset latched faults command 74
reset to default values command 74
RF waveguide switch 42, 82
fault finding 101, 103
installing
receive 44
transmit 42
safety precautions 82
RS232 interface 37
RS422/485 interface 38
S
safety notices
radiation safety 123
safety precautions
fuse protection 83
overcurrent protection 83
RF waveguide switch 82
serial interface 37
BUC 50
commands 63
Help 64
Output 72
Reset 74
Set 65
View 73
connecting to the BUC 39
control during setup 39
FSK interface 38
monitor and control 62
RS232 interface 37
RS485 interface 38
servicing 82
Set commands 65
set burst mode power threshold command 68
set compensation frequency command 66
set echo command 71
set local oscillator command 69
set on line command 70
set packet address command 71
set packet protocol command 71
set redundant mode command 69
set serial interface command 70
set transmit attenuator command 67
set transmit default command 69
set transmit on command 65
set transmit power alarm threshold command
67
signal switching 17
stream switching 76
switch on
redundancy switching system 53
switches
redundancy controller 19
T
technical assistance 84
test procedures for fault finding 97
transmit frequency bands 7
U
unpacking
redundancy switching system 28
Block Up Converter Systems 6700/6900 series User Guide
Index-3
Index
V
View commands 73
example outputs 115
view build standard data 117
view fault status 116
view identity and configuration data 116
view limit data 116
view operational data 115
view protocol data 117
view system status 115
view build standard data command 73
view fault status command 73
view identity and configuration data
command 73
view limit data command 73
view operational data command 73
view protocol data command 73
view system status command 73
W
warm standby 79
Index-4
Block Up Converter Systems 6700/6900 series User Guide
www.codan.com.au
Head Office
Codan Limited
ABN 77 007 590 605
81 Graves Street
Newton SA 5074
AUSTRALIA
Telephone +61 8 8305 0311
Facsimile +61 8 8305 0411
[email protected]
Codan (UK) Ltd
Gostrey House
Union Road
Farnham Surrey GU9 7PT
UNITED KINGDOM
Telephone +44 1252 717 272
Facsimile +44 1252 717 337
[email protected]
Codan US, Inc.
8430 Kao Circle
Manassas VA 20110
USA
Telephone +1 703 361 2721
Facsimile +1 703 361 3812
[email protected]

advertisement

Was this manual useful for you? Yes No
Thank you for your participation!

* Your assessment is very important for improving the workof artificial intelligence, which forms the content of this project

Related manuals

Download PDF

advertisement