Sharp R-480E User`s guide
advertisement
User’s Guide
Notations Used in This Guide
• Safety indications
The documentation and the projector use graphical symbols to show how to use the projector safely.
The indications and their meaning are as follows. Make sure you understand them properly before reading the guide.
Warning
This symbol indicates information that, if ignored, could possibly result in personal injury or even death due to incorrect handling.
Caution
This symbol indicates information that, if ignored, could possibly result in personal injury or physical damage due to incorrect handling.
• General information indications
Attention a s
[Name]
Menu Name
Indicates procedures which may result in damage or injury if sufficient care is not taken.
Indicates additional information and points which may be useful to know regarding a topic.
Indicates a page where detailed information regarding a topic can be found.
Indicates that an explanation of the underlined word or words in front of this symbol appears in the glossary of terms. See the "Glossary" section of the "Appendices".
s
Indicates the name of the buttons on the remote control or the control panel.
Example: [Esc] button
Indicates Configuration menu items.
Example:
Select Brightness from Image.
Image - Brightness
Contents
3
Notations Used in This Guide . . . . . . . . . . . . . . . . . . . . . . . . 2
Introduction
Projector Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Enabling projection from a short distance . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
Drawing function (EB-485Wi/EB-480i/EB-475Wi only) . . . . . . . . . . . . . . . . . . . . 8
Easy writing on a whiteboard or blackboard using the pattern function . . . . . . . . 8
Connecting with a USB cable and projecting (USB Display) . . . . . . . . . . . . . . . . 8
Connecting to a network and projecting images from the computer's screen
Enlarge and project your files with the Document Camera . . . . . . . . . . . . . . . . . 8
Easy connection to a computer with Quick Wireless . . . . . . . . . . . . . . . . . . . . . 9
Part Names and Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Attaching the feet (Only models with feet supplied) . . . . . . . . . . . . . . . . . . . . 14
Replacing the remote control batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Remote control operating range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi Only) . . . . . . . . . . . . . . . . . . . 20
Replacing the battery for the Easy Interactive Pen . . . . . . . . . . . . . . . . . . . . . 20
Replacing the tip of the Easy Interactive Pen . . . . . . . . . . . . . . . . . . . . . . . . . 21
Pen Tray (EB-485Wi/EB-480i/EB-475Wi Only) . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Preparing the Projector
Installing the Projector . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Connecting Equipment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Basic Usage
Projecting images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Automatically Detect Input Signals and Change the Projected Image (Source Search)
Switching to the Target Image Using the Remote Control . . . . . . . . . . . . . . . . . . 41
Adjusting Projected Images . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjusting the Position of the Image (Image Shift) . . . . . . . . . . . . . . . . . . . . . . . . 48
Adjusting the Vertical Position of the Image (Models Supplied with the Feet Only)
Lowering the height of the image . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Contents
4
Adjusting the Horizontal Position of the Image (Models Supplied with the Feet Only)
Selecting the Projection Quality (Selecting Color Mode) . . . . . . . . . . . . . . . . . . . 51
Changing the Aspect Ratio of the Projected Image . . . . . . . . . . . . . . . . . . . . . . . 52
Changing the aspect mode (EB-485Wi/EB-485W/EB-475Wi/EB-475W only) . . . . . 53
Changing the aspect mode (EB-480i/EB-480/EB-470 only) . . . . . . . . . . . . . . . . 54
Useful Functions
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 57
Drawing with the projector's built-in function . . . . . . . . . . . . . . . . . . . . . . . . 57
Operating as a mouse and drawing by connecting to a computer (Computer
Operating as a mouse and drawing by connecting to a computer (Computer
Install Easy Interactive Driver (Mac OS X only) . . . . . . . . . . . . . . . . . . . . . . . . 64
Operating the computer with a pen instead of a mouse . . . . . . . . . . . . . . . . . 65
Allowing two people to use pens at the same time . . . . . . . . . . . . . . . . . . . . . 65
Projection Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 67
Hiding the Image and Sound Temporarily (A/V Mute) . . . . . . . . . . . . . . . . . . . . . 67
Using the Remote Control to Operate the Mouse Pointer (Wireless Mouse) . . . . . . 70
Projecting Without a Computer (Slideshow) . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Specifications for files that can be projected using Slideshow . . . . . . . . . . . . . . 74
Slideshow operating methods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Projecting image files in a folder in sequence (Slideshow) . . . . . . . . . . . . . . . . 78
Image file display settings and Slideshow operation settings . . . . . . . . . . . . . . 78
Security Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Monitoring and Controlling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84
Changing Settings Using a Web Browser (Web Control) . . . . . . . . . . . . . . . . . . . . 84
Displaying the Web Control screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Displaying the Web Remote screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Using the Mail Notification Function to Report Problems . . . . . . . . . . . . . . . . . . . 87
®
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Operating a projector from your computer . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Contents
5
Configuration Menu
Using the Configuration Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
List of Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Notes on operating the Network menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . 106
Troubleshooting
Using the Help . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Problem Solving . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Moving images are not displayed (only the moving image portion turns black)
The message Not supported is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
The message No Signal is displayed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Images are fuzzy, out of focus, or distorted . . . . . . . . . . . . . . . . . . . . . . . . . 125
Interference or distortion appear in images . . . . . . . . . . . . . . . . . . . . . . . . . 126
The mouse cursor flickers (only when projecting USB Display) . . . . . . . . . . . . 126
The image is truncated (large) or small, or the aspect is not suitable . . . . . . . . 126
The projector does not turn on . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Problems Relating to the Easy Interactive Function . . . . . . . . . . . . . . . . . . . . . . 129
Cannot the projector's built-in drawing function . . . . . . . . . . . . . . . . . . . . . 129
Cannot operate as a mouse and draw by connecting to a computer . . . . . . . . 130
The message An error occurred in the Easy Interactive Function. is displayed
The Easy Interactive Pen does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
The reaction time for the Easy Interactive Pen is slow (only when projecting USB
The dot does not move to the next position . . . . . . . . . . . . . . . . . . . . . . . . . 131
No sound can be heard or the sound is faint . . . . . . . . . . . . . . . . . . . . . . . . 132
No sound can be heard from the microphone . . . . . . . . . . . . . . . . . . . . . . . 132
The remote control does not work . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
I want to change the language for messages and menus . . . . . . . . . . . . . . . . 133
Mail is not received even if an error occurs with the projector . . . . . . . . . . . . . 134
Image file names are not displayed correctly in Slideshow . . . . . . . . . . . . . . . 134
Cannot change settings using a web browser . . . . . . . . . . . . . . . . . . . . . . . 134
About Event ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Maintenance
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
Contents
6
Replacing Consumables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
Appendix
Optional Accessories and Consumables . . . . . . . . . . . . . . . . . . . . 146
Screen Size and Projection Distance . . . . . . . . . . . . . . . . . . . . . . . . 147
Projection Distance (For EB-485Wi/EB-485W/EB-475Wi/EB-475W) . . . . . . . . . . . . 147
Projection Distance (For EB-480i/EB-480/EB-470) . . . . . . . . . . . . . . . . . . . . . . . 148
Supported Monitor Displays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Computer signals (analog RGB) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Input signal from the HDMI port . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Appearance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
Glossary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
General Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 163
Introduction
This chapter explains the projector's features and the part names.
Projector Features
8
Projection Functions
Enabling projection from a short distance
You can project large images from a short distance without having to move the projector away from the screen. By mounting the projector on a ceiling or wall, you can minimize shadows cast on the screen even when you are standing near it and avoid being dazzled by the projected light.
s
"Screen Size and Projection Distance" p.147
Connecting with a USB cable and projecting (USB Display)
By simply connecting the supplied or a commercially available USB cable, you can project images from a computer's screen without a computer cable.
s
"Projecting with USB Display" p.41
Connecting to a network and projecting images from the computer's screen
You can connect the projector to a computer on a network and project the computer's screen using the supplied EasyMP Network Projection
(application software).
s EasyMP Network Projection Operation Guide
Drawing function (EB-485Wi/EB-480i/EB-475Wi only)
You can write characters and draw figures on the projected screen using the electronic pen (Easy Interactive Pen). You can also draw on a computer screen from the projected screen by using the Easy Interactive Tools software supplied.
s
"Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)" p.57
Easy writing on a whiteboard or blackboard using the pattern function
You can project ruled lines and grid patterns. This is useful when drawing diagrams on a whiteboard or blackboard.
s
Settings - Pattern
Enhanced security functions
• Password Protect to restrict and manage users
By setting a password you can restrict who can use the projector.
s
"Managing Users (Password Protect)" p.80
• Control Panel Lock restricts button operation on the control panel
You can use this to prevent people changing projector settings without permission at events, in schools, and so on.
s
"Restricting Operation (Control Panel Lock)" p.82
• Equipped with various anti-theft devices
The projector is equipped with the following types of anti-theft security devices.
• Security slot
• Security cable installation point s
Optional Functions
Enlarge and project your files with the Document Camera
You can project paper documents and objects using the optional Document
Camera. Image focus is automatically adjusted using the auto focus function. You can also enlarge images using digital zoom.
s
Projector Features
Easy connection to a computer with Quick Wireless
By simply connecting the optional Quick Wireless Connection USB Key to a computer, you can project the computer's screen. (Windows computers only) s
9
Part Names and Functions
Front/Top
Name
A Remote receiver
B Lamp cover
C Lamp cover fixing screw
D Air exhaust vent
E Cable cover fixing screws
Function
Receives signals from the remote control.
Open when replacing the projector's lamp.
s
Screw to fix the lamp cover in place.
s
Exhaust vent for air used to cool the projector internally.
Caution
While projecting, do not put your face or hands near the air exhaust vent, and do not place objects that may become warped or damaged by heat near the vent.
Screws to fix the cable cover in place.
Name
F Cable cover
G Control panel
H Speaker
10
Function
Open by loosening both of the screws when connecting to an input port or installing the wireless LAN unit.
Operates the projector.
s
Outputs audio.
Part Names and Functions
11
Side
Name
A Air filter cover open/close lever
B Security cable installation point
Function
Opens and closes the air filter cover.
Pass a commercially available wire lock through here and lock it in place.
s
"Installing the wire lock" p.83
Name Function
C Wireless LAN indicator Indicates the access status to the optional wireless LAN unit.
D Easy Interactive
Function receiver
(EB-485Wi/EB-480i/
EB-475Wi only)
E Obstacle sensor
Receives signals from the Easy Interactive Pen. s
"Easy Interactive Function (EB-485Wi/EB-480i/
Detects obstacles that are interfering with the projection area.
s
"Cleaning the Obstacle Sensor" p.137
F Remote receiver Receives signals from the remote control.
G Projection window Projects images.
Warning
• Do not look into the projection window while projecting.
• Do not place any objects or put your hand near the projection window. This area is dangerous as it reaches high temperatures due to the con‐ centrated projection light.
H Security slot
I Air filter cover
J Air intake vent
(air filter)
K Focus lever
The security slot is compatible with the Microsaver
Security System manufactured by Kensington.
s
Open when changing the air filter or operating the focus lever.
Takes in air to cool the projector internally.
s
"Cleaning the Air Filter" p.138
s
"Replacing the Air Filter" p.142
Adjusts the image focus.
Open the air filter cover to operate.
Part Names and Functions
Interface
The following ports are available under the cable cover.
Name
G LAN port
H USB-A port
I USB-B port
Name
A Wireless LAN unit installation section
B Audio1 port
C Audio2 port
D
E
F
Computer1 port
Computer2 port
Monitor Out port
Function
Install the optional Wireless LAN unit here.
s
"Installing the Optional Wireless LAN Unit" p.37
Inputs audio from equipment connected to the
Computer1 port.
• Inputs audio from equipment connected to the
Computer2 port.
• Inputs audio from other devices when projecting images from the device connected to the USB-A port.
Inputs image signals from a computer and component video signals from other video sources.
Inputs image signals from a computer and component video signals from other video sources.
Outputs analog RGB signals input from the Computer1 port to an external monitor. You cannot output signals input from other ports or component video signals.
J HDMI port
K RS-232C port
L Audio Out port
M Power inlet
12
Function
Connects a LAN cable to connect to a network.
• Connects a USB memory device or a digital camera, and projects images as a Slideshow.
s
"Projecting Without a Computer (Slideshow)" p.74
• Connects the optional Document Camera.
• Connects the projector to a computer via the supplied or a commercially available USB cable, and projects the images on the computer.
s
"Projecting with USB Display" p.41
• Connects the projector to a computer via the supplied or a commercially available USB cable to use the Wireless
Mouse function.
s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• Connects the projector to a computer via the supplied or a commercially available USB cable to use the Easy
Interactive Pen as a mouse or as a pen to draw on the projected screen. (EB-485Wi/EB-480i/EB-475Wi only) s
"Operating as a mouse and drawing by connecting to a computer (Computer Interactive)" p.57
Inputs video signals from HDMI compatible video equipment and computers. This projector is compatible
s
When controlling the projector from a computer, connect it to the computer with an RS-232C cable. This port is for control use and should not normally be used.
s
Outputs audio from the currently projected image or the
Mic port to an external speaker.
Connects the power cord to the projector.
s
"From Installation to Projection" p.39
Part Names and Functions
Name
N Audio-L/R port
O Video port
P S-Video port
Q Mic port
Function
Inputs audio from equipment connected to the S-Video port or the Video port.
Inputs composite video signals from video sources.
For S-video signals from video sources.
Inputs audio from the microphone.
s
"Connecting a microphone" p.33
Base
13
Name
A Ceiling mount fixing points (five points)
B Security cable installation point
Function
Attach the optional Ceiling Mount here when suspending the projector from a ceiling.
s
"Installing the Projector" p.24
s
Pass a commercially available wire lock through here and lock it in place.
s
"Installing the wire lock" p.83
Part Names and Functions
C
Name
Rear foot fixing points
(two points)
Function
Attach the feet when using the projector on a surface such as a desk. (Only models with feet supplied) s
"Attaching the feet (Only models with feet supplied)" p.14
D Wall mount fixing points (four points)
Attach the setting plate when mounting on a wall. (Only models with setting plate supplied) s Installation Guide s
E Front foot fixing point Attach the foot with a spacer when using the projector on a surface such as a desk. (Only models with feet supplied) s
"Attaching the feet (Only models with feet supplied)" p.14
Attaching the feet (Only models with feet supplied)
Insert the feet into the foot fixing points.
B Insert the rear feet (x2) into the foot fixing points.
a
You can install this projector vertically on a desk.
s
14
A Insert the foot with the spacer into the front foot fixing point.
Part Names and Functions
15
Control Panel
Name
A Status indicators
B [Source Search] button
C [Enter] button
[ ]
Function
Indicates the projector's status using color, and by being lit or flashing.
s
"Reading the Indicators" p.118
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.
• If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Position.
D
Name
[w][v] button
Function
• Displays the Keystone screen.
s
• If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.
s
"Using the Configuration Menu" p.95
s
E
F
[Help] button
[Esc] button
Displays and closes the help screen which shows you how to deal with problems if they occur.
s
• Stops the current function.
• If pressed when the Configuration menu is displayed, it moves to the previous menu level.
s
"Using the Configuration Menu" p.95
G [Tele]/[Wide] buttons
• Adjusts the size of the projection screen. Press the [Tele] button to reduce the size of the projection screen and press the [Wide] button to increase the size of the projection screen.
• Corrects keystone distortion in the horizontal direction when the Keystone screen is displayed.
s
• If pressed when the Configuration menu or the Help screen is displayed, these buttons select menu items and setting values.
s
"Using the Configuration Menu" p.95
s
H [Menu] button Displays and closes the Configuration menu.
s
"Using the Configuration Menu" p.95
I [t] button Turns the projector power on or off.
s
"From Installation to Projection" p.39
Part Names and Functions
Remote Control
16
Name
A [t] button
B [Computer] button
C
D
E
F
G
H
[Video] button
Numeric buttons
[Auto] button
[Aspect] button
[Num] button
[Menu] button
Function
Turns the projector power on or off.
s
"From Installation to Projection" p.39
Each time you press the button, the input changes between images from the Computer1 port and the Computer2 port.
Each time the button is pressed, the image cycles through the S-Video, Video, and HDMI ports.
• Enter the Password.
s
"Setting Password Protect" p.80
• Use this button to enter numbers in Network settings from the Configuration menu.
If pressed while projecting analog RGB signals from
Computer1 port or Computer2 port, you can automatically optimize Tracking, Sync., and Position.
Each time the button is pressed, the aspect mode changes.
s
"Changing the Aspect Ratio of the Projected Image" p.52
Hold down this button and press the numeric buttons to enter passwords and numbers.
s
"Setting Password Protect" p.80
Displays and closes the Configuration menu.
s
"Using the Configuration Menu" p.95
Part Names and Functions
17
Name
I
[ ][ ][ ][ ] button
J
K
[ ] button
[User] button
Function
• When the Configuration menu or Help screen is displayed, pressing these buttons selects menu items and setting values.
s
"Using the Configuration Menu" p.95
• When projecting a Slideshow, pressing these buttons displays the previous/next image, rotates the image, and so on.
s
"Projecting Without a Computer (Slideshow)" p.74
• During Wireless Mouse function, the mouse pointer moves in the direction of the button that was pushed.
s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When the Configuration menu or the Help screen is displayed, it accepts and enters the current selection and moves to the next level.
s
"Using the Configuration Menu" p.95
• Acts as a mouse's left button when using the Wireless
Mouse function.
s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
Select any frequently used item from the seven or eight available Configuration menu items, and assign it to this button. By pressing the [User] button, the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/adjustments.
s
The following item is assigned by default.
• EB-485Wi/EB-480i/EB-475Wi: Auto Calibration
• EB-485W/EB-480/EB-475W/EB-470: Power
Consumption
L
Name
[Page] buttons
[[][]]
Function
M [A/V Mute] button
Changes pages in files such as PowerPoint files when using the following projection methods.
• When using the Wireless Mouse function s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When using USB Display s
"Projecting with USB Display" p.41
• When connecting to a network
When projecting images using Slideshow, pressing these buttons displays the previous/next image file.
• Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
• You can change the Projection mode as follows by pressing the button for about five seconds.
FrontWFront/Upside Down
RearWRear/Upside Down
N [E-Zoom] buttons
[z][x]
Enlarges or reduces the image without changing the projection size.
s
"Enlarging Part of the Image (E-Zoom)" p.69
O Strap attachment hole Allows you to attach a commercially available strap to the remote control.
P [Help] button Displays and closes the help screen which shows you how to deal with problems if they occur.
s
Q [Freeze] button Pauses or resumes image playback.
s
"Freezing the Image (Freeze)" p.67
R [Volume] buttons
[a][b]
[a] Decreases the volume.
[b] Increases the volume.
s
S [Pointer] button Displays the on-screen pointer.
s
"Pointer Function (Pointer)" p.68
Part Names and Functions
18
T
U
V
W
X
Name
[Esc] button
[Color Mode] button
[LAN] button
[USB] button
[Source Search] button
Y Remote control lightemitting area
Function
• Stops the current function.
• If pressed when the Configuration menu is displayed, it moves to the previous level.
s
"Using the Configuration Menu" p.95
• Acts as a mouse's right button when using the Wireless
Mouse function.
s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
Each time the button is pressed, the color mode changes.
s
"Selecting the Projection Quality (Selecting Color
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to that image.
Each time the button is pressed, it cycles through the following images:
• USB Display
• Images from the device connected to the USB-A port
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
Outputs remote control signals.
Replacing the remote control batteries
If the remote control becomes unresponsive or inoperable after it has been used for some time, the batteries may have reached the end of their service life. When this happens, replace them with new batteries. Obtain two AA size manganese or alkaline batteries. You cannot use other batteries except for the AA size manganese or alkaline.
Attention
Make sure you read the following manual before handling the batteries.
s Safety Instructions a Remove the battery cover.
While pushing the battery cover catch, lift the cover up.
b Replace the old batteries with new batteries.
Part Names and Functions
Caution
Check the positions of the (+) and (-) marks inside the battery holder to ensure the batteries are inserted the correct way.
c Reattach the battery cover.
Press the battery cover until it clicks into place.
Remote control operating range
19
Part Names and Functions
20
Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi
Only)
There are two types of Easy Interactive Pens with different colored bottom sections. You cannot use Easy Interactive Pens with the same colored bottom sections at the same time.
s
Name
C Battery indicator
A
Name
Pen tip button
Function
• Touch the screen to select an item such as an icon.
• Touch the screen and move to draw on the projected screen.
• Move over the screen without touching to move the pointer.
s
"Easy Interactive Function (EB-485Wi/EB-480i/
s
B Strap attachment hole Allows you to attach a commercially available strap.
D Slide switch
E Battery cover
Function
Indicates the remaining battery power when the power is turned on.
• Turns green for several seconds when the battery is charged.
• Flashes green for several seconds when the battery is low.
• Does not light when the battery is exhausted. Change the battery.
s
"Replacing the battery for the Easy Interactive Pen" p.20
Switches the Easy Interactive Pen on and off.
When turned on, it takes a few seconds before the Easy
Interactive Pen is operational.
Open this cover when replacing the battery. s
"Replacing the battery for the Easy Interactive Pen" p.20
Replacing the battery for the Easy Interactive Pen
The battery indicator on the Easy Interactive Pen lights or flashes when the power is turned on. Does not light or flash when the battery is exhausted.
When the indicator no longer lights or flashes, replace the battery. Use one of the following types of battery. Other chargeable batteries cannot be used.
• AA size manganese battery
• AA size alkaline manganese battery
• SANYO eneloop * (HR-3UTG/HR-3UTGA)
* eneloop
®
® is a registered trademark of Sanyo Electronic Co., Ltd.
Attention
Make sure you read the following manual before handling batteries.
s Safety Instructions
Part Names and Functions a Remove the battery cover.
While pushing the battery cover catch, lift the cover up.
b Replace the old battery with a new battery.
Replacing the tip of the Easy Interactive Pen
Replace the tip of the Easy Interactive Pen when it is worn.
s
a Turn the tip of the pen to remove it.
Caution
Check the positions of the (+) and (-) marks inside the battery holder to ensure the battery is inserted the correct way.
c Replace the battery cover.
Press the battery cover until it clicks into place.
b Turn the new tip to attach it.
21
Part Names and Functions
Pen Tray (EB-485Wi/EB-480i/EB-475Wi Only)
Name
A Fixing points
B Security hole
Function
Attach the pen tray to a whiteboard or wall.
Pass a commercially available lock through here.
a
It is recommended that the pen tray be tightened with two commercially available M5 bolts.
22
Preparing the Projector
This chapter explains how to install the projector and connect projection sources.
Installing the Projector
Installation Methods
The projector supports the following six different projection methods.
Install the projector according to the installation location.
Turn the projector off when you are changing the installation method. Turn the projector back on after changing the installation method.
a
You cannot use the Easy Interactive Function while the Projection setting is Rear/Upside Down or Rear. (EB-485Wi/EB-480i/EB-475Wi only) s
"Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)" p.57
• Mount the projector on a wall or ceiling and project images from in front of a screen.
(Front/Upside Down projection)
• Mount the projector on a wall or ceiling and project images from behind a translucent screen. (Rear/Upside Down pro‐ jection)
24
• Project images from in front of the screen. (Front projection)
• Project images from behind a translucent screen. (Rear projec‐ tion) a
Attach the feet when using the projector on a surface such as a desk.
s
"Attaching the feet (Only models with feet supplied)" p.14
• Place the projector vertically and project images from in front of the screen. (Front/Upside Down projection)
• Place the projector vertically and project images from behind the screen (Rear/Upside Down pro‐ jection)
Installing the Projector
Warning
• A special method of installation is required when suspending the projector from a wall or ceiling. If it is not installed correctly, it could fall causing an accident and injury.
• If you use adhesives on the wall mount plate fixing points or the ceiling mount fixing points to prevent the screws from loosening, or if you use things such as lubricants or oils on the projector, the projector case may crack causing it to fall from its mount. This could cause serious injury to anyone under the mount and could damage the projector.
When installing or adjusting the mount, do not use adhesives to prevent the screws from loosening and do not use lubricant or oil and so on.
• Do not cover the projector's air intake vent or air exhaust vent. If either of the vents are covered, the internal temperature could rise and cause a fire.
a • When mounting the projector on a wall or ceiling, or placing the projector vertically, make sure you use the correct tools for the installation method.
s
• The default Projection setting is Front/Upside Down. You can change to other Projection settings from the Configuration menu.
s Extended - Projection
• You can change the Projection setting as follows by pressing down the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Upside Down
RearWRear/Upside Down
25
Connecting Equipment
The port name, location, and connector orientation differ depending on the source being connected.
Connecting a Computer
To project images from a computer, connect the computer using one of the following methods.
A B When using a commercially available computer cable
C
Connect the computer's display output port to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the computer's audio output port to the projector's Audio1 or Audio2 port using a commercially available audio cable.
When using the supplied or a commercially available USB cable
D
Connect the computer's USB port to the projector's USB-B port.
You can send the audio with the projected image.
When using a commercially available HDMI cable
Connect the computer's HDMI port to the projector's HDMI port.
You can send the audio with the projected image.
26
Connecting Equipment a • If it is difficult to connect the computer cable to the projector's Computer2 port, try disconnecting the cable from the Computer1 port, connecting the cable to the Computer2 port, and then reconnecting the cable to the Computer1 port.
• You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input
• You can use a USB cable to connect the projector to a computer to project images from the computer. This function is called USB Display.
s
"Projecting with USB Display" p.41
27
Connecting Equipment
28
Connecting Image Sources
To project images from DVD players or VHS video and so on, connect to the projector using one of the following methods.
A When using a commercially available video cable
Connect the video output port on the image source to the projector's Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.
When using a commercially available S-video cable B
Connect the video output port on the image source to the projector's S-Video port using a commercially available video cable.
You can output audio from the projector's speaker by connecting the audio output port on the image source to the projector's Audio-L/R port using a commercially available audio cable.
C D When using the optional component video cable s
"Optional Accessories and Consumables" p.146
Connect the component output port on the image source to the projector's Computer1 or Computer2 port.
You can output audio from the projector's speaker by connecting the image source's audio output port to the projector's Audio1 or Audio2 port using a commercially available audio cable.
E When using a commercially available HDMI cable
Connect the HDMI port on the image source to the projector's HDMI port using a commercially available HDMI cable.
You can send the audio with the projected image.
Connecting Equipment
Attention
• If the input source is on when you connect it to the projector, it could cause a malfunction.
• If the orientation or shape of the plug differs, do not try to force it in. The device could be damaged or could malfunction.
29
Connecting Equipment a • You can switch the audio input by using Audio Input.
s Extended - Operation - Audio Input
• If the source you want to connect to has an unusually shaped port, use the cable supplied with the device or an optional cable to connect to the projector.
• When using a commercially available 2RCA(L/R)/stereo mini-pin audio cable, make sure it is labeled "No resistance".
30
Connecting Equipment
Connecting USB Devices
You can connect devices such as USB memory, the optional Document Camera, and USB compatible hard disks and digital cameras.
Using the USB cable supplied with the USB device, connect the USB device to the USB-A port on the projector.
31
When the USB device is connected, you can project image files on the USB memory or digital camera using Slideshow.
s
"Projecting Without a Computer (Slideshow)" p.74
If the Document Camera is connected while projecting images from another input port, press the [USB] button on the remote control, or the [Source Search] button on the control panel, to switch to images from the Document Camera.
s
"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.40
a
While projecting images from a USB device, if you want to connect an audio output device, connect it to the Audio2 port.
Connecting Equipment
32
Attention
• If you use a USB hub, operation may not be performed correctly. Devices such as digital cameras and USB devices should be connected to the projector directly.
• When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
• Connect a digital camera or hard disk to the projector using a USB cable supplied with or specified for use with the device.
• Use a USB cable less than 3 m in length. If the cable exceeds 3 m, Slideshow may not function correctly.
Removing USB devices
After finishing projecting, remove USB devices from the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.
Connecting Equipment
Connecting a microphone
You can output microphone audio from the projector's speaker by connecting a commercially available dynamic microphone.
33 a • Plug-in-power is not supported.
• Adjust Mic Input Level if the microphone audio is difficult to hear, or if it is too loud resulting in a crackling sound.
s Settings - Mic Input Level
• Make the following settings to output audio from a microphone when the projector is in standby mode.
Set Standby Mode to Communication On. s Extended - Standby Setup - Standby Mode
Set Standby Microphone to On. s Extended - Standby Setup - Standby Microphone
Connecting Equipment
Connecting External Equipment
You can output images and audio by connecting an external monitor or speaker.
A When outputting images to an external monitor
Connect the external monitor to the projector's Monitor Out port using the cable supplied with the external monitor.
B When outputting audio to an external speaker
Connect the external speaker to the projector's Audio Out port using a commercially available audio cable.
34
Connecting Equipment a • If you set Standby Mode to Communication On, you can output images to an external monitor even if the projector is in standby mode. You can also output audio to an external speaker. Audio input from the HDMI port, USB-A port, USB-B port, or the LAN port cannot be output.
s Extended - Standby Setup - Standby Mode
• Only analog RGB signals from the Computer1 port can be output to an external monitor. You cannot output signals input from other ports or component video signals.
• Setting gauges for functions such as Keystone, Configuration menu, or Help screens are not output to the external monitor.
• When the audio cable jack is inserted into the Audio Out port, audio stops being output from the projector's built-in speakers and switches to external output.
35
Connecting Equipment
Connecting a LAN Cable
Connect a LAN port on network hubs or other equipment to the projector's LAN port with a commercially available 100BASE-TX or 10BASE-T LAN cable.
36 a
To prevent malfunctions, use a category 5 shielded LAN cable.
Connecting Equipment
Installing the Optional Wireless LAN Unit
a Remove both of the cable cover fixing screws to open the cable cover.
b Install the Wireless LAN unit.
37
Basic Usage
This chapter explains how to project and adjust images.
Projecting images
From Installation to Projection
This section explains the procedure for connecting the projector to a computer with the computer cable and projecting images.
ON
39 d e
Turn on the computer.
Change the computer's screen output.
When using a laptop computer, you need to change the screen output from the computer.
Hold down the Fn key (function key), and press the b key.
a • The method for changing differs depending on the computer being used. See the documentation supplied with the computer.
• Press the [t] button twice to turn the projector off.
If the image is not projected, you can change the projected image using one of the following methods.
• Press the [Source Search] button on the control panel or the remote control.
s
"Automatically Detect Input Signals and Change the Projected Image
• Press the button for the target port on the remote control.
s
"Switching to the Target Image Using the Remote Control" p.41
a
After projecting the image, adjust the image if necessary.
s
"Correcting Keystone Distortion" p.45
s
a b c
Connect the projector to an electrical outlet with the power cord.
Connect the projector to the computer with the computer cable.
Turn on the projector.
Projecting images
Automatically Detect Input Signals and Change the Projected Image (Source Search)
Press the [Source Search] button to project images from the port currently receiving an image.
Using Remote Control Using the Control Panel a
The following screen is displayed while no image signals are input.
40
Computer1 Computer2 S-Video Video
LAN USB USB Display HDMI
When two or more image sources are connected, press the [Source Search] button until the target image is projected.
When your video equipment is connected, start playback before beginning this operation.
Projecting images
41
Switching to the Target Image Using the Remote
Control
You can change directly to the target image by pressing the following buttons on the remote control.
Remote control
Projecting with USB Display
You can use the supplied or a commercially available USB cable to connect the projector to a computer to project images from the computer.
You can send the computer's audio with the projected image.
Set USB Type B to USB Display/Easy Interactive Function or Wireless
Mouse/USB Display to use USB Display on EB-485Wi/EB-480i/EB-475Wi.
s
Extended - USB Type B
A Each time the button is pressed, it cycles through the images being input from the following sources.
• Computer1 port
• Computer2 port
B Each time the button is pressed, it cycles through the images being input from the following sources.
• S-Video port
• Video port
• HDMI port
C Each time the button is pressed, it cycles through the images being input from the following sources.
• USB Display
• Images from the device connected to the USB-A port
D Changes to the images projected with EasyMP Network Projection. When projecting using the optional Quick Wireless Connection USB Key, this button switches to that image.
System requirements
For Windows
OS
CPU
Windows 2000 * 1
Windows XP
Windows Vista
Professional 32 bit
Home Edition 32 bit
Tablet PC Edition 32 bit
Ultimate 32 bit
Enterprise 32 bit
Business 32 bit
Home Premium 32 bit
Home Basic 32 bit
Windows 7 Ultimate 32/64 bit
Enterprise 32/64 bit
Professional 32/64 bit
Home Premium 32/64 bit
Home Basic 32 bit
Starter 32 bit
Mobile Pentium III 1.2 GHz or faster
Recommended: Pentium M 1.6 GHz or faster
Projecting images
42
Amount of Mem‐ ory
256 MB or more
Recommended: 512 MB or more
Hard Disk Space 20 MB or more
Display Resolution of no less than 640x480 and no higher than
1600x1200.
Display color of 16-bit color or greater
* 1 Service Pack 4 only
For Mac OS X
OS
CPU
Mac OS X 10.5.x 32 bit
Mac OS X 10.6.x 32/64 bit
Mac OS X 10.7.x 32/64 bit
Power PC G4 1GHz or faster
Recommended: Core Duo 1.83GHz or faster
512 MB or more Amount of Memo‐ ry
Hard Disk Space 20 MB or more
Display Resolution of no less than 640x480 and no higher than
1680x1200.
Display color of 16-bit color or greater
Connecting for the first time
The first time you connect the projector and the computer using the USB cable, the driver needs to be installed. The procedure is different for
Windows and Mac OS X.
a • You do not need to install the driver the next time you connect.
• When inputting images from multiple sources, change the input source to USB Display.
• If you are using a USB hub, operations may not be performed correctly. Connect the USB cable directly to the projector.
• You cannot change option settings while using USB Display.
For Windows a Connect the computer's USB port to the projector's USB-B port using the supplied or a commercially available USB cable.
a
For Windows 2000 or Windows XP, a message asking you if you want to restart your computer may be displayed. Select
No .
For Windows 2000
Double-click Computer, EPSON PJ_UD, and then
EMP_UDSE.EXE
.
For Windows XP
Driver installation starts automatically.
b
For Windows Vista/Windows 7
When the dialog box is displayed, click Run EMP_UDSE.exe.
When the License Agreement screen is displayed, click Agree.
Projecting images
43 c d
Computer images are projected.
It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.
Disconnect the USB cable when you are finished.
When disconnecting the USB cable, there is no need to use Safely
Remove Hardware .
a • If it is not installed automatically, double-click My Computer
- EPSON_PJ_UD - EMP_UDSE.EXE on your computer.
• If nothing is projected for some reason, click All Programs -
EPSON Projector - Epson USB Display - Epson USB
Display Vx.xx
on your computer.
• When using a computer running Windows 2000 under user authority, a Windows error message is displayed and you may not be able to use the software. In this case, try updating
Windows to the latest version, restart, and then try to connect again.
For more details, contact your local dealer or the nearest address provided in the following document.
s Epson Projector Contact List
For Mac OS X a Connect the computer's USB port to the projector's USB-B port using the supplied or a commercially available USB cable.
The Setup folder of USB Display is displayed in the Finder.
Double-click the USB Display Installer icon.
b c Follow the on-screen instructions to install.
d e f
When the License Agreement screen is displayed, click Agree.
Enter the administrator authority password and start the installation.
When the installation is complete, the USB Display icon is displayed in the Dock and menu bar.
Computer images are projected.
It may take a while for computer images to be projected. Until the computer images are projected, leave the equipment as is and do not disconnect the USB cable or turn off the power of the projector.
When you have finished, select Disconnect from the menu bar or from the USB Display icon on the Dock. You can then disconnect the USB cable.
a • If the USB Display setup folder is not displayed automatically in the Finder, double-click EPSON PJ_UD - USB Display
Installer on your computer.
• If nothing is projected for some reason, click the USB
Display icon in the Dock.
• If there is no USB Display icon in the Dock, double-click
USB Display from the Applications folder.
• If you select Exit from the USB Display icon menu on the
Dock, USB Display does not start automatically when you connect the USB cable.
Uninstalling
For Windows 2000 a b c d
Click Start, select Settings, and then click Control Panel.
Double-click Add/Remove Programs.
Click Change or Remove Programs.
Select Epson USB Display and click Change/Remove.
Projecting images
For Windows XP a b c
Click Start, and then click Control Panel.
Double-click Add or Remove Programs.
Select Epson USB Display and click Remove.
For Windows Vista/Windows 7 a b c
Click Start, and then click Control Panel.
Click Uninstall a program under Programs.
Select Epson USB Display and click Uninstall.
For Mac OS X a Open the Applications folder, double-click USB Display, and then double-click Tool.
b Run USB Display Uninstaller.
44
Adjusting Projected Images
Correcting Keystone Distortion
You can correct keystone distortion using one of the following methods.
• H/V-Keystone
Manually correct distortion in the horizontal and vertical directions independently.
H/V-Keystone
Manually correct distortion in the horizontal and vertical directions independently. H/V-Keystone correction is ideal for fine-tuning keystone distortion.
You can use H/V-Keystone to correct the projected image under the following conditions.
Correction angle: Approx. 5˚ right and left/Approx. 5˚ up and down a Press the [ w
] or [ v
] buttons on the control panel during projection to display the Keystone screen.
45
• Quick Corner
Manually correct the four corners independently.
b Press the following buttons to correct keystone distortion.
Press the [ w
] or [ v
] buttons to correct vertical distortion.
a
When you correct keystone distortion, the projected image may be reduced.
Adjusting Projected Images
Press the [Tele] or [Wide] buttons to correct horizontal distortion.
46 a
You can set H/V-Keystone from the Configuration menu.
s Settings - Keystone - H/V-Keystone
Quick Corner
This allows you to manually correct each of the four corners of the projected image separately.
a Press the [Menu] button while projecting.
s
"Using the Configuration Menu" p.95
Using Remote Control Using the Control Panel c Select Quick Corner, and then press the [ ] button.
d Select the corner to correct using the [ ], [ ], [ ], and[ ] buttons on the remote control, or the [ w ], [ v ], [Wide], and [Tele] buttons on the control panel, and then press the [ ] button.
b Select Keystone from Settings.
Adjusting Projected Images
47 e Correct the position of the corner using the [ ], [ ], [ ], and
[ ] buttons on the remote control, or the [ w
], [ v
], [Wide], and [Tele] buttons on the control panel.
When you press the [ ] button, the screen shown in step 4 is displayed.
If the message "Cannot adjust any further." is displayed while adjusting, you cannot adjust the shape any further in the direction indicated by the gray triangle.
f Repeat procedures 4 and 5 as needed to adjust any remaining corners.
g When you are done, press the [Esc] button to exit the correction menu.
Because Keystone was changed to Quick Corner, the corner selection screen shown in step 4 is displayed the next time you press the [ w ] or [ v ] buttons on the control panel. Change Keystone to
H/V-Keystone if you want to perform horizontal and vertical correction using the [ w ] and [ v ] buttons on the control panel.
s
Settings - Keystone - H/V-Keystone
Adjusting Projected Images
48 a
If the [Esc] button is held down for about two seconds while the corner selection screen from step 4 is displayed, the following screen is displayed.
Adjusting the Position of the Image (Image Shift)
You can fine tune the position of the image without moving the projector.
Reset Quick Corner : Resets the result of Quick Corner corrections.
Switch to H/V-Keystone : Switches the correction method to
H/V-Keystone .
s
Adjusting the Image Size
Press the [Wide] and [Tele] buttons on the control panel to adjust the size of the projected image.
a Perform Adjust Zoom or Keystone.
s
"Adjusting the Image Size" p.48
s
"Correcting Keystone Distortion" p.45
The Image Shift screen is displayed after you have made adjustments.
b Adjust the position of the projected image.
a
You can also make adjustments from the configuration menu.
s Settings - Zoom
Adjusting Projected Images
49 a • You cannot adjust the image position when Zoom is set to the maximum Wide position.
• The Image Shift setting is retained even if the projector is turned off.
You need to re-adjust the position if you change the installation location or angle of the projector.
• You can also use the Configuration menu to adjust the position of the image.
s Settings - Image Shift
Using Remote Control Using the Control Panel
Adjusting the Vertical Position of the Image
(Models Supplied with the Feet Only)
Extend the feet. You can adjust the vertical position of the image by tilting the projector up to 1.5˚.
a
The larger the angle of tilt, the harder it becomes to focus. Install the projector so that it only needs to be tilted at a small angle.
You can shift the image diagonally by pressing any pair of adjacent
[ ], [ ], [ ], and [ ] buttons, or a combination of [ w ], [ v ], [Wide], and [Tele] buttons.
c Press the [Esc] button to close the adjustment screen.
The adjustment screen disappears if no operation is performed after approximately 10 seconds.
Raising the height of the image
A You can raise the height of the image by extending the rear feet.
B Retract the rear feet to return the image to its original height.
Adjusting Projected Images
Lowering the height of the image
A You can lower the height of the image by extending the front foot.
B Retract the front foot to return the image to its original height.
Adjusting the Horizontal Position of the Image
(Models Supplied with the Feet Only)
Extend and retract the rear feet to adjust the projector's horizontal tilt.
B Retract the rear foot.
Correcting the Focus
You can correct the focus using the focus lever.
Adjusting the Volume
You can adjust the volume using one of the following methods.
50
A Extend the rear foot.
Adjusting Projected Images
• Press the [Volume] buttons on the remote control to adjust the volume.
[ a ] Decreases the volume.
[ b ] Increases the volume.
Remote control
• Adjust the volume from the Configuration menu.
s
Settings - Volume
Caution
Do not start when the volume is set too high.
A sudden increase in volume may cause loss of hearing. Always lower the volume before powering off, so that you can power on and then gradually increase the volume.
51
Mode
Presentation
Theatre
Photo *1
Sports *2 sRGB
Blackboard
Application
Ideal for making presentations using color materials in a bright room.
Ideal for watching films in a dark room. Gives images a natural tone.
Ideal for projecting still pictures, such as photos, in a bright room. The images are vivid and brought into contrast.
Ideal for watching TV programmes in a bright room. The images are vivid and brought to life.
Ideal for images that conform to the sRGB
color standard.
Even if you are projecting onto a blackboard
(greenboard), this setting gives your images a natural tint, just like when projecting onto a screen.
Ideal for making presentations using a whiteboard.
Whiteboard
* 1 This selection is only available when the input signal is RGB or when the source is USB Display, USB, or LAN.
* 2 This selection is only available when the input signal is component video, or when the input source is Video or S-Video.
Each time you press the [Color Mode] button, the Color Mode name is displayed on the screen and the Color Mode changes.
Remote control
Selecting the Projection Quality (Selecting Color
Mode)
You can easily obtain the optimum image quality simply by selecting the setting that best corresponds to your surroundings when projecting. The brightness of the image varies depending on the mode selected.
Dynamic
Mode Application
Ideal for use in a bright room. This is the brightest mode, and reproduces shadow tones well.
Adjusting Projected Images
52 a
You can set Color Mode from the Configuration menu.
s Image - Color Mode
Setting Auto Iris
By automatically setting the luminance according to the brightness of the displayed image, it lets you enjoy deep and rich images.
a Press the [Menu] button.
s
"Using the Configuration Menu" p.95
Using Remote Control Using the Control Panel b Select Auto Iris from Image.
c Select On.
The setting is stored for each Color Mode.
d Press the [Menu] button to finish making settings.
a
Auto Iris can only be set when the Color Mode is set to
Dynamic or Theatre.
Changing the Aspect Ratio of the Projected Image
You can change the Aspect Ratio
of the projected image to suit the type, the ratio of height and width, and the resolution of the input signals.
Available Aspect Modes vary depending on the image signal currently being projected.
Adjusting Projected Images
Changing methods
Each time you press the [Aspect] button on the remote control, the aspect mode name is displayed on the screen and the aspect ratio changes.
Remote control a
You can set the aspect ratio from the Configuration menu.
s Signal - Aspect
A Normal or Auto
B 16:9
C Full
D Zoom
E Native
Changing the aspect mode (EB-485Wi/EB-485W/EB-475Wi/EB-475W only)
Projecting images from video equipment or from the HDMI port
Each time the [Aspect] button on the remote control is pressed, the aspect mode changes in the order Normal or Auto, 16:9, Full, Zoom, and
Native .
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
Projecting images from a computer
The following shows projection examples for each aspect mode.
Aspect mode
XGA 1024X768(4:3)
Input Signal
WXGA 1280X800(16:10)
Normal
53
Adjusting Projected Images
Aspect mode
16:9
XGA 1024X768(4:3)
Input Signal
WXGA 1280X800(16:10)
Full
54
Changing the aspect mode (EB-480i/EB-480/EB-470 only)
Projecting images from video equipment
Each time the [Aspect] button is pressed, the aspect mode changes in the order 4:3 and 16:9.
When inputting a 720p/1080i signal and the aspect mode is set to 4:3, a 4:3 zoom is applied (the right and left sides of the image are cut off).
Example: 720p signal input (resolution: 1280x720, aspect ratio: 16:9)
Zoom
Native a
If parts of the image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the size of the computer panel.
s Signal - Resolution
A 4:3
B 16:9
Projecting images from the HDMI port
Each time the [Aspect] button is pressed, the aspect mode changes in the order Auto, 4:3, and 16:9.
Example: 1080p signal input (resolution: 1920x1080, aspect ratio: 16:9)
A Auto
Adjusting Projected Images
B 4:3
C 16:9
Projecting images from a computer
Each time the [Aspect] button is pressed, the aspect mode changes in the order Normal, 4:3, and 16:9.
The following shows projection examples for each aspect mode.
Aspect mode
XGA 1024X768(4:3)
Input Signal
WXGA 1280X800(16:10)
Normal
4:3
16:9 a
If parts of the image are missing, set the Resolution setting to Wide or Normal from the Configuration menu, according to the size of the computer panel.
s Signal - Resolution
55
Useful Functions
This chapter explains useful functions for giving presentations and so on, and the security functions.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
57
Introducing the Easy Interactive Function
The Easy Interactive Function allows you to perform the following operations using the Easy Interactive Pen.
Drawing with the projector's built-in function
You can write and draw on the projected screen using the projector's built-in drawing function without having to use any additional software.
You can draw on any image source.
s
"Drawing with the Projector's Built-in Function" p.58
Operating as a mouse and drawing by connecting to a computer
(Computer Interactive)
You can connect the projector to a computer to operate the computer from the projected screen. This makes presentations and lessons effective and easy to understand.
Two people can use Easy Interactive Pens simultaneously by using the supplied drawing software Easy Interactive Tools.
s
"Operating as a mouse and drawing by connecting to a computer
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
58
Attention
The Easy Interactive Function operates by infrared communication. Note the following important points when using this function.
• Make sure there is no strong light or sunlight shining on the Easy Interactive
Function receiver or the projection screen.
• If there is any dust stuck to the Easy Interactive Function receiver, it could interfere with infrared communication and you may not be able to use the function normally.
• Do not put paint or any stickers on the cover of the Easy Interactive
Function receiver.
• Install the projector so that the Easy Interactive Function receiver is not too close to fluorescent lights.
• Do not use an infrared remote control or infrared microphone in the same room because the Easy Interactive Pen may malfunction.
• The Easy Interactive Function may be interrupted by electromagnetic interference from nearby equipment (such as electric motors or transformers).
• The Easy Interactive Pen is not waterproof. Do not use it with wet hands, or in locations where it may get wet.
• Do not hold the black section of the pen tip of the Easy Interactive Pen, and make sure this section does not get damaged or soiled. Otherwise, the Easy
Interactive Pen may not work.
• When operating Keystone, performance for the Easy Interactive Function may decline.
Drawing with the Projector's Built-in Function
Procedure
a b
Turn on the projector.
Perform the pen calibration.
You can skip this step if pen calibration is already complete.
s
c Put the Easy Interactive Pen close to the projected screen near the toolbar tabs [ ] on the left and right of the screen.
d Click one of the toolbar tabs [
The toolbar is displayed.
].
When the toolbar is displayed, you can write on the projected screen using the Easy Interactive Pen.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
59 s
"Easy Interactive Pen (EB-485Wi/EB-480i/EB-475Wi Only)" p.20
s
a
The projector's built-in drawing function is not available if both of the following conditions are met.
• Extended - USB Type B is set to Easy Interactive Function or USB
Display/Easy Interactive Function from the configuration menu.
• Images are projected from the source specified in Extended - Easy
Interactive Function - Use Source from the configuration menu.
Calibrating the pen
You need the Easy Interactive Pen to use the Easy Interactive Function.
Make sure you perform pen calibration when using the Easy Interactive Pen for the first time so that the projector recognizes the position of the pen correctly.
Auto Calibration
This function automatically calibrates the pen.
a Set Extended - Easy Interactive Function to Auto Calibration from the configuration menu.
b Adjust the focus by following the on-screen instructions.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
60
If Auto Calibration is unsuccessful, try Manual Calibration.
s
Manual Calibration
This function allows you to manually calibrate the pen.
a Set Extended - Easy Interactive Function to Manual Calibration from the configuration menu.
s
c Select "Yes".
Use the [ ] button on the remote control or control panel to select
"Yes". You cannot select Easy Interactive Pen when performing operations from the configuration menu.
d The pattern image is projected and calibration starts.
Wait until calibration is complete.
Do not obstruct the projected light while the pattern image is being projected.
a
• Select [
] using Easy Interactive Pen on the toolbar and execute
Auto Calibration if the discrepancy is small.
• However, execute Auto Calibration from the remote control or control panel when you are calibrating the pen for the first time.
• For pen positioning, do not switch between making operations using the remote control and making operations using the Easy Interactive
Pen.
b Adjust the focus by following the on-screen instructions.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only) a
Make sure you touch the center of the dot. Otherwise, it may not be positioned correctly.
61 c Use the [ ] button on the remote control or control panel to select "Yes".
d A dot is displayed on the projected screen.
Touch the center of the dot with the tip of the Easy Interactive Pen.
The dot disappears and then appears at the next position.
e The dot appears at the top left first and then moves towards the bottom right.
Repeat step 4 until all of the dots disappear.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only) a • If you touch the wrong position, press the [Esc] button on the remote control or control panel to return to the previous dot.
You cannot go back further than the previous dot.
• Press and hold the [Esc] button to cancel the calibration.
• It may take several seconds after all of the dots have disappeared until calibration is complete.
When you need to calibrate the pen
The position where you are drawing with the Easy Interactive Pen and where the drawing is displayed may not match in the following situations.
• After performing Keystone correction.
• After adjusting the image size.
• After performing Image Shift.
• After changing the projector's position.
Calibrate the pen again if you notice any discrepancy in positioning.
Toolbar functions
The following toolbar modes are available.
Annotation mode You can draw lines and shapes on the projected image.
Whiteboard mode You can project solid color backgrounds such as a whiteboard and write or draw text and pictures. In addition to the plain background, you can also choose other background patterns such as lines and grid lines.
Annotation mode Whiteboard mode
62
A Annotation mode tab
Switches to Annotation mode.
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
D
E
B
C
F
Whiteboard mode tab
Switches to Whiteboard mode.
Undo
Undoes the previous operation.
Redo
Cancels an undo operation and restores the previous status.
Freeze (Annotation mode only)
Pauses the projected image. Each time you touch the icon, Freeze turns on or off.
a
You can also use the [Freeze] button on the remote control.
s
"Freezing the Image (Freeze)" p.67
Select background (Whiteboard mode only)
Allows you to select a pattern from the six background patterns provided for Whiteboard mode.
G
H
I
J
K
L
E-Zoom
Displays a target allowing you to enlarge the image at the center of the target. You can move the target with the Easy Interactive Pen.
[ ]: Enlarges the image.
[ ]: Reduces the image.
[ ]: Increases the magnification by one.
[ ]: Quits E-Zoom.
a • You can scroll the enlarged image by dragging it with the Easy Interactive Pen.
• You cannot use E-Zoom from the remote control, document camera, or Crestron RoomView ® while operating the Easy Interactive Pen in E-Zoom.
s
"Enlarging Part of the Image (E-Zoom)" p.69
s
®
Calibrating the pen
Carries out Auto Calibration.
s
Pen
Switches to a pen to draw freely. Click [ ] on the left of the icon to change the color and width of the pen line.
Highlighter pen
Switches to a highlighter pen that can draw translucent lines. Click
[ ] on the left of the icon to change the color and width of the highlighter pen.
Black pen
Switches to a black pen to draw freely. Click on the right of the icon to draw thick lines, and click on the left of the icon to draw fine lines.
Red pen
Switches to a red pen to draw freely. Click on the right of the icon to draw thick lines, and click on the left of the icon to draw fine lines.
63
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
64
M
N
O
Blue pen
Switches to a blue pen to draw freely. Click on the right of the icon to draw thick lines, and click on the left of the icon to draw fine lines.
Eraser
Switches to an eraser. Click on the right of the icon to erase wider areas, and click on the left of the icon to erase narrower areas.
Clear screen
Clears everything drawn on the displayed page.
a
• Click [ ] to hide the toolbar.
• You can display the toolbar again by clicking one of the toolbar tabs
[ ] displayed on the left and right of the screen.
• If you click [ ], the toolbar is hidden each time you draw something. By default, the toolbar is always displayed.
• The toolbar tabs [ ] can be moved up and down.
• The toolbar tabs [ ] disappear after a set length of time if they are not used. Put the Easy Interactive Pen close to the projected screen to display the toolbar tabs [ ].
You need a drawing function already available on your computer.
The Easy Interactive Tools software is supplied with this projector. See the following manual for more information on the Easy Interactive Tools functions.
s Easy Interactive Tools Ver.2 Operation Guide a • Connect the projector to the computer using a USB cable to link with the computer's functions.
s
• Make the following settings to link with the computer's functions.
• Set Extended - USB Type B to Easy Interactive Function or USB
Display/Easy Interactive Function from the configuration menu.
• Set the source where the computer is connected in Extended -
Easy Interactive Function - Use Source from the configuration menu.
s Extended - Easy Interactive Function
• You cannot use the projector's built-in drawing function if you switch to the image source set in Use Source.
Install Easy Interactive Driver (Mac OS X only)
Easy Interactive Driver is required to use the Easy Interactive Pen with Mac
OS X.
Operating as a mouse and drawing by connecting to a computer (Computer Interactive)
You can connect the projector to a computer to operate the computer from the projected screen and allow two people to draw simultaneously.
You need to install Easy Interactive Driver for Mac OS X.
s
"Install Easy Interactive Driver (Mac OS X only)" p.64
System Requirements
OS Mac OS X 10.3.9 or later
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
Mac OS X 10.7.x
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
65
CPU
Amount of Memo‐ ry
Power PC G3 900 MHz or faster
Recommended: Intel Core Duo 1.5 GHz or faster
256 MB or more
Recommended: 512 MB or more
Hard Disk Space 100 MB or more
Display Resolutions no lower than XGA (1024 x 768) and no higher than WUXGA (1920 x 1200)
Display color in 16-bit color or greater b c
Run Easy Interactive Driver Uninstaller in the Tools folder.
Follow the on-screen instructions to uninstall.
Installing a
You can skip the following procedure if you installed Easy Interactive
Tools using the Easy Install option as this already installs the Easy
Interactive Driver.
s Easy Interactive Tools Ver.2 Operation Guide a b
Turn on your computer.
Insert the "EPSON Projector Software for Easy Interactive Function"
CD-ROM into your computer.
c d
Double-click the Install Navi icon in the EPSON window.
Select Custom Install, and then follow the on-screen instructions to install.
e
Uninstalling
Restart the computer.
a Open the Applications folder and double-click Easy Interactive
Driver.
Operating the computer with a pen instead of a mouse
You can operate a computer using the Easy Interactive Pen instead of a mouse.
If you set Enable Right Click to On in Extended - Easy Interactive
Function from the configuration menu, a long press of the Easy Interactive
Pen functions as a right click.
Allowing two people to use pens at the same time
Easy Interactive Tools allows two people to use Easy Interactive Pens at the same time.
s Easy Interactive Tools Ver.2 Operation Guide
Set Number of Pen Users to Two Users in Extended - Easy Interactive
Function from the configuration menu.
a • When Number of Pen Users is set to One User, you can use the
Easy Interactive Pen with tablet PCs in Windows Vista/7. You can also use ink features for Office in Windows Vista/7.
• You can set Easy Interactive Pen operations from the configuration menu.
• Set Pen Operation Mode to Pen to enable the pen function in
Windows Vista/7.
• You can swap Right Click and Left Click in Advanced - Pen Tip
Button .
s Extended - Easy Interactive Function
Easy Interactive Function (EB-485Wi/EB-480i/EB-475Wi only)
66
Adjusting the pen operation area
When using the Easy Interactive Function by connecting to a computer, the pen operation area is automatically adjusted if the resolution of the computer changes. You do not need to perform pen alignment again.
a
You can turn this function On or Off in Auto Adjust Pen Area from the configuration menu. The default setting is On.
s Extended - Easy Interactive Function - Advanced
If you notice the Easy Interactive Pen is out of position even when Auto
Adjust Pen Area is set to On, you can try Manual Adj. Pen Area.
s
Manual Adj. Pen Area a Select Manual Adj. Pen Area for Easy Interactive Function from the configuration menu.
a • Adjust to fit the projected image within the screen.
• Display the computer's desktop screen so that you can check the position of the mouse pointer easily.
b Use the [ ] button on the remote control to select "Yes".
The mouse pointer moves towards the top left.
c When the mouse pointer stops at the top left, touch the tip of the mouse pointer with the Easy Interactive Pen.
The mouse pointer moves towards the bottom right.
d When the mouse pointer stops at the bottom right, touch the tip of the mouse pointer with the Easy Interactive Pen.
Projection Functions
67
Hiding the Image and Sound Temporarily (A/V
Mute)
You can switch off the image on the screen when you want to focus the audience's attention on what you are saying, or when you do not want to display operations such as changing files.
a • If you use this function when projecting moving images, the images and sound continue to be played back by the source, and you cannot return to the point where A/V Mute was activated.
• Microphone audio is still output even when A/V Mute is turned on.
• You can select the screen displayed when the [A/V Mute] button is pressed from the Configuration menu.
s Extended - Display - A/V Mute
• The lamp is still lit during A/V Mute, so the lamp hours continue to accumulate.
Each time you press the [A/V Mute] button, A/V Mute turns on or off.
Remote control
Freezing the Image (Freeze)
When Freeze is activated on moving images, the frozen image continues to project on the screen, so you can project a moving image one frame at a time like a still photo. Also, you can perform operations such as changing between files during presentations from a computer without projecting any images if the Freeze function is activated beforehand.
Each time you press the [Freeze] button, Freeze turns on or off.
Remote control
Projection Functions
68 a • Audio does not stop.
• For moving images, the images continue to play back while the screen is frozen, so it is not possible to resume projection from the point where the screen was frozen.
• If the [Freeze] button is pressed while the Configuration menu or the Help screen is displayed, the menu or the Help screen that is displayed is closed.
• Freeze still works while E-Zoom is being used.
Pointer Function (Pointer)
This allows you to move a pointer icon on the projected image, and helps you draw attention to the area you are talking about.
b Move the Pointer icon ( ).
Remote control
When any pair of adjacent [ ], [ ], [ ], or [ ] buttons are pressed at the same time, the pointer can be moved diagonally.
a
You can select the shape of the pointer icon from the
Configuration menu.
s Settings - Pointer Shape
a Display the Pointer.
Each time you press the [Pointer] button, the pointer appears or disappears.
Remote control
Projection Functions
Enlarging Part of the Image (E-Zoom)
This is useful when you want to expand images to see them in greater detail, such as graphs and tables.
69 b Move the Cross ( ) to the area of the image that you want to enlarge.
Remote control a Start E-Zoom.
Press the [ z
] button to display the Cross ( ).
Remote control
When any pair of adjacent [ ], [ ], [ ], or [ ] buttons are pressed at the same time, the pointer can be moved diagonally.
c Enlarge.
Remote control
[z] button: Expands the area each time it is pressed. You can expand quickly by holding the button down.
[x] button: Reduces images that have been enlarged.
[Esc] button: Cancels E-Zoom.
a • The enlargement ratio appears on the screen. The selected area can be enlarged to between 1 to 4 times in 25 incremental steps.
• During enlarged projection, press the [
], [ ], [ ], and
[ ] buttons to scroll the image.
Projection Functions
Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)
You can control the computer's mouse pointer from the projector's remote control. This function is called Wireless Mouse.
The following operating systems are compatible with Wireless Mouse.
OS
Windows
Windows 98
Windows 98SE
Windows Me
Windows 2000
Windows XP
Windows Vista
Windows 7
Mac OS X
Mac OS X 10.3.x
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
Mac OS X 10.7.x
* It may not be possible to use the Wireless Mouse function under some versions of the operating systems.
Use the following procedure to enable the Wireless Mouse function.
a Set USB Type B to Wireless Mouse/USB Display from the configuration menu. (EB-485Wi/EB-480i/EB-475Wi only) s
Extended - USB Type B
b Connect the projector to the computer with the supplied or a commercially available USB cable.
s
c Change the source to one of the following.
• USB Display
• Computer1
• Computer2
• HDMI s
"Switching to the Target Image Using the Remote Control" p.41
Once set, the mouse pointer can be controlled as follows.
Moving the mouse pointer
[ ][ ][ ][ ] buttons:
Moves the mouse pointer.
Mouse clicks
Drag and drop
Page Up/Down
[Esc] button: Right click.
[ ] button: Left click. Press quickly twice to double-click.
While holding down the [ ] button, press the [ ], [ ], [ ], or [ ] button to drag.
Release the [ ] button to drop at the desired location.
[[] button: Moves to the previous page.
[]] button: Moves to the next page.
70
Projection Functions
71 a
• When any pair of adjacent [
], [ ], [ ], or [ ] buttons are pressed at the same time, the pointer can be moved diagonally.
• If the mouse button settings are set to reverse on the computer, the operation of the remote control buttons will also be reversed.
• The Wireless Mouse function does not work under the following conditions.
• When Extended - USB Type B is set to anything other than
Wireless Mouse/USB Display (EB-485Wi/EB-480i/EB-475Wi only).
• When displaying the configuration menu or help.
• When operating functions other than the Wireless Mouse function
(such as adjusting the volume).
However, when using the E-Zoom or Pointer function, the page up or down function is available.
Saving a User's Logo
You can save the image that is currently being projected as a User's Logo.
You can use the registered user's logo as a display when projection starts or no image signal is being input.
s
Extended - Display
a
Once a User Logo has been saved, the logo cannot be returned to the factory default.
a Project the image you want to save as the User's Logo, and then press the [Menu] button.
s
"Using the Configuration Menu" p.95
Using Remote Control Using the Control Panel b Select User's Logo from Extended.
Projection Functions
72 d Move the box to select the part of the image to use as the User's
Logo.
You can perform the same operations from the projector's control panel.
Remote control a • When User's Logo Protect from Password Protect is set to
On , a message is displayed and the User's Logo cannot be changed. You can make changes after setting User's Logo
Protect to Off.
s
"Managing Users (Password Protect)" p.80
• If User's Logo is selected when Keystone, E-Zoom, Aspect, or
Adjust Zoom is being performed, the function currently being performed is cancelled.
c When the message "Choose this image as the User's Logo?" is displayed, select Yes.
a
When you press the [ ] button on the remote control or the control panel, the screen size may change depending on the signal to match the actual resolution of the image signal.
a
You can save at 400x300 dots in size.
e When you press the [ ] button and the message "Select this image?" is displayed, select Yes.
Projection Functions f Select the zoom factor from the zoom setting screen.
73 a
When a User Pattern is saved, the previous User Pattern is erased.
a Project the image you want to use as the User Pattern, and then press the [Menu] button.
s
"Using the Configuration Menu" p.95
Using Remote Control Using the Control Panel g When the message "Save this image as the User's Logo?" is displayed, select Yes.
The image is saved. After the image has been saved, the message
"Completed." is displayed.
a • When a User's Logo is saved, the previous User's Logo is erased.
• It takes a while to save. Do not operate the projector or any connected equipment while it is saving, otherwise malfunctions may occur.
Saving User Pattern
There are four types of patterns registered to the projector, such as ruled lines and grid patterns.
s
Settings - Pattern - Pattern Type
You can also save the image that is currently being projected as a User
Pattern.
b Select Pattern from Settings.
c Select User Pattern.
Projection Functions
74
Projecting Without a Computer (Slideshow)
By connecting a USB storage device such as a USB memory or a USB hard disk to the projector, you can project the files stored on the device without using a computer. This function is called Slideshow.
a • You may not be able to use USB storage devices that incorporate security functions.
• You cannot correct keystone distortion while projecting a Slideshow, even if you press the [w] and [v] buttons on the control panel.
a
If User Pattern is selected when Keystone, E-Zoom, Aspect,
Adjust Zoom, or Image Shift are being performed, the function currently being performed is temporarily canceled.
d When "Do you want to use the currently projected image as the
User Pattern?" is displayed, select Yes.
e When you press the [ ] button, the message "Do you save this image as the User Pattern?" is displayed. Select Yes.
The image is saved. After the image has been saved, the message
"The User Pattern setting is complete." is displayed.
a • Once a User Pattern has been saved, User Pattern cannot be returned to the factory default.
• It takes a while to save a User Pattern. Do not operate the projector or any connected equipment while saving the user pattern, otherwise malfunctions may occur.
Specifications for files that can be projected using Slideshow
Type Notes
Image
File Type (Ex‐ tension)
.jpg
.bmp
.gif
.png
The following cannot be projected.
- CMYK color mode format
- Progressive format
- Images with a resolution greater than 8192x8192
Due to the characteristics of JPEG files, images may not be projected clearly if the compression ratio is too high.
Cannot project images with a resolution greater than 1280x800.
• Cannot project images with a resolution greater than 1280x800.
• Cannot project animated GIFs.
Cannot project images with a resolution greater than 1280x800.
Projection Functions
75 a • When connecting and using a USB-compatible hard disk, make sure you connect the AC adaptor supplied with the hard disk.
• The projector does not support some file systems, so use media that has been formatted in Windows.
• Format the media in FAT16/32.
Slideshow examples
Projecting images stored on USB storage
Starting Slideshow a Change the source to USB.
s
"Switching to the Target Image Using the Remote Control" p.41
b Connect the USB storage device or digital camera to the projector.
s
Slideshow starts and the file list screen is displayed.
• JPEG files are displayed as thumbnails (file contents are displayed as small images).
• Other files or folders are displayed as icons as shown in the following table.
Icon File
JPEG files *
Icon File
BMP files
GIF files PNG files s
"Projecting the selected image" p.77
s
"Projecting image files in a folder in sequence (Slideshow)" p.78
Slideshow operating methods
Although the following steps are explained based on the remote control, you can perform the same operations from the control panel.
* When it cannot be displayed as a thumbnail, it is displayed as an icon.
Projection Functions a • You can also insert a memory card into a USB card reader and then connect the reader to the projector. However, some commercially available USB card readers may not be compatible with the projector.
• If the following screen (Select Drive screen) is displayed, use the
[ ], [ ], [ ], and [ ] buttons to select the drive you want to use, and then press the [ ] button.
76
• You can display the Select Drive screen by positioning the cursor on
Select Drive at the top of the file list screen, and then press the [ ] button.
Projecting images a Use the [ ], [ ], [ ], and [ ] buttons to select the file or folder you want to project.
a
If not all of the files and folders are displayed on the current screen, press the []] button on the remote control, or position the cursor on Next Page at the bottom of the screen and press the [ ] button.
To return to the previous screen, press the [[] button on the remote control, or position the cursor on Previous Page at the top of the screen and press the [ ] button.
b Press the [ ] button.
The selected image is displayed.
When a folder is selected, the files in the selected folder are displayed. To return to the screen which was displayed before opening the folder, position the cursor on Back to Top and press the
[ ] button.
Rotating images
You can rotate the played images in 90˚ increments. The rotating function is also available during Slideshow.
Projection Functions a b
Play images, or run Slideshow.
While projecting, press the [ ] or [ ] button.
77 a Start Slideshow.
The file list screen is displayed.
s
b Press the [ ], [ ], [ ], and [ ] buttons to select the image file you want to project.
Stopping Slideshow
To close Slideshow, disconnect the USB device from the USB port on the projector. For devices such as digital cameras or hard disks, turn off the device and then remove it from the projector.
Projecting the selected image
Attention
Do not disconnect the USB storage device while it is being accessed.
Slideshow may not operate correctly.
c Press the [ ] button.
The image is displayed.
a
Press the [ ][ ] buttons to move to the next or previous image file.
Projection Functions
78 d Press the [Esc] button to return to the file list screen.
Projecting image files in a folder in sequence (Slideshow)
You can project the image files in a folder in sequence, one at a time. This function is called Slideshow. Use the following procedure to run
Slideshow.
a
To change files automatically when you run Slideshow, set Screen
Switching Time from Option in Slideshow to anything other than No.
The default setting is 3 seconds.
s
"Image file display settings and Slideshow operation settings" p.78
a screen, projection starts again from the beginning when it reaches the end.
s
"Image file display settings and Slideshow operation settings" p.78
You can proceed to the next screen, return to the previous screen, or stop playback while projecting a Slideshow.
If Screen Switching Time on the Option screen is set to No, files do not change automatically when you select Play Slideshow. Press the
[ ] button, the [ ] button, or the []] button to continue to the next file.
a Start Slideshow.
The file list screen is displayed.
s
b Use the [ ], [ ], [ ], and [ ] buttons to position the cursor on the folder you want to run the Slideshow, and then press the
[ ] button.
c Select Slideshow at the bottom of the file list screen, and then press the [ ] button.
Slideshow starts, and the image files in the folder are automatically projected in sequence, one at a time.
When the last file is projected, the file list is displayed again automatically. If you set Continuous Play to On in the Option
You can use the following functions when projecting an image file with
Slideshow.
• Freeze s
"Freezing the Image (Freeze)" p.67
• A/V Mute s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.67
• E-Zoom s
"Enlarging Part of the Image (E-Zoom)" p.69
Image file display settings and Slideshow operation settings
You can set the file display order and Slideshow operations on the Option screen.
a Press the [ ], [ ], [ ] and [ ] buttons to position the cursor over the folder where you want to set display conditions, and then press the [Esc] button. Select Option from the submenu displayed, then press the [ ] button.
Projection Functions b When the following Option screen is displayed, set each of the items.
Enable the settings by positioning the cursor on the target item and pressing the [ ] button.
The following table shows the details for each item.
79 c Use the [ ], [ ], [ ], and [ ] buttons to position the cursor over OK, and then press the [ ] button.
The settings are applied.
If you do not want to apply the settings, position the cursor on
Cancel , and then press the [ ] button.
Display Order You can select to display the files in Name Order or Date
Order .
Sort Order
Continuous
Play
You can select to sort the files In Ascending or In
Descending order.
You can set whether to repeat the Slideshow.
Screen Switch‐ ing Time
Effect
You can set the time for a single file to be displayed in Play
Slideshow. You can set a time between No (0) to 60
Seconds. When you set No, auto play is disabled.
You can set the screen effects when changing slides.
Security Functions
80
The projector has the following enhanced security functions.
• Password Protect
You can limit who can use the projector.
• Control Panel Lock
You can prevent people changing the settings on the projector without permission.
s
"Restricting Operation (Control Panel Lock)" p.82
• Anti-Theft Lock
The projector is equipped with the following anti-theft security device.
s
• User's Logo Protect
Even if someone tries to change the User's Logo set by the owner of the projector, it cannot be changed. When User's Logo Protect is set to On, the following setting changes for the User's Logo are prohibited.
• Capturing a User's Logo
• Setting Display Background, Startup Screen, or A/V Mute from
Display s
Extended - Display
• Network Protect
When Network Protect is set to On, changing the settings for Network is prohibited.
s
Managing Users (Password Protect)
When Password Protect is activated, people who do not know the password cannot use the projector to project images even if the projector power is on.
Furthermore, the user's logo that is displayed when you turn on the projector cannot be changed. This acts as an anti-theft device as the projector cannot be used even if it is stolen. At the time of purchase,
Password Protect is not activated.
Setting Password Protect
Use the following procedure to set Password Protect.
a During projection, hold down the [Freeze] button for about five seconds.
The Password Protect setting menu is displayed.
Remote control
Kinds of Password Protect
The following three kinds of Password Protect settings can be made according to how the projector is being used.
• Power On Protect
When Power On Protect is On, you need to enter a preset password after the projector is plugged in and turned on (this also applies to Direct
Power On). If the correct password is not entered, projection does not start.
Security Functions
81 a • If Password Protect is already activated, you must enter the password.
If the password is entered correctly, the Password Protect setting menu is displayed.
s
• When the password is set, stick the supplied password protect sticker in a visible position on the projector as a further theft deterrent.
b Select the type of Password Protect you want to set, and then press the [ ] button.
(3) While holding down the [Num] button, enter a four digit number using the numeric buttons. The number entered is displayed as "* * * *". When you enter the fourth digit, the confirmation screen is displayed.
Remote control
(4) Re-enter the password.
The message "Password accepted." is displayed.
If you enter the password incorrectly, a message is displayed prompting you to re-enter the password.
c Select On, and then press the [ ] button.
Press the [Esc] button, the screen displayed in step 2 is displayed again.
d Set the password.
(1) Select Password, and then press the [ ] button.
(2) When the message "Change the password?" is displayed, select Yes and then press the [ ] button. The default password is set to "0000". Change this to your own desired Password. If you select No, the screen displayed in step 2 is displayed again.
Entering the Password
When the password entry screen is displayed, enter the password using the remote control.
While holding down the [Num] button, enter the password by pressing the numeric buttons.
Security Functions
82
When you enter the correct password, Password Protect is temporarily released.
Attention
• If an incorrect password is entered three times in succession, the message
"The projector's operation will be locked." is displayed for approximately five minutes, and then the projector switches to standby mode. If this happens, disconnect the power plug from the electrical outlet and then reinsert it and turn the projector's power back on. The projector displays the password entry screen again so that you can enter the correct password.
• If you have forgotten the password, make a note of the "Request Code: xxxxx" number that appears on the screen and contact the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
• If you continue to repeat the above operation and input the wrong Password
30 times in succession, the following message is displayed and the projector does not accept any more Password entries. "The projector's operation will be locked. Contact Epson as described in your documentation." s Epson Projector Contact List
Restricting Operation (Control Panel Lock)
Do one of the following to lock the operation buttons on the control panel.
• Full Lock
All of the buttons on the control panel are locked. You cannot perform any operations from the control panel, including turning the power on or off.
• Partial Lock
All of the buttons on the control panel, except for the [ t
] button, are locked.
This is useful at events or shows when you want to deactivate all buttons during projection or at schools when you want to limit button operation.
The projector can still be operated using the remote control.
a Press the [Menu] button while projecting.
s
"Using the Configuration Menu" p.95
Using Remote Control Using the Control Panel b Select Control Panel Lock from Settings.
c Select either Full Lock or Partial Lock according to your purpose.
Security Functions
83 d Select Yes when the confirmation message is displayed.
The control panel buttons are locked according to the setting you chose.
a
You can release the control panel lock by one of the following two methods.
• Select Off from Control Panel Lock.
s Settings - Control Panel Lock
• Press and hold down the [ ] button on the control panel for about seven seconds, a message is displayed and the lock is released.
Anti-Theft Lock
The projector is equipped with the following types of anti-theft security devices.
• Security slot
The security slot is compatible with the Microsaver Security System manufactured by Kensington.
See the following for more details on the Microsaver Security System.
s http://www.kensington.com/
• Security cable installation point
A commercially available theft-prevention wire lock can be passed through the installation point to secure the projector to a desk or pillar.
Installing the wire lock
Pass an anti-theft wire lock through the installation point.
See the documentation supplied with the wire lock for locking instructions.
Monitoring and Controlling
84
About EasyMP Monitor
EasyMP Monitor lets you carry out operations such as checking the status of multiple Epson projectors that are connected to a network at a computer monitor, and controlling the projectors from the computer.
You can download EasyMP Monitor from the following Web site.
http://www.epson.com
The following provides brief descriptions of the monitoring and control functions that can be carried out using EasyMP Monitor.
• Registering projectors for monitoring and control
Projectors on the network can be searched for automatically, and you can then select which projectors you want to register from the projectors that are detected.
You can register target projectors by entering their IP addresses.
• Registered projectors can also be assigned to groups so that they can be monitored and controlled in groups.
• Monitoring the status of registered projectors
You can check the power status (ON/OFF) for projectors and problems or warnings that require attention by using the icons.
You can select groups of projectors or a single projector and then check the cumulative lamp operating time or information such as input sources, problems, and warnings for the projectors.
• Controlling registered projectors
Projectors can be selected in groups or as single projectors, and you can then carry out operations for the selected projectors such as turning the power on and off and switching their input sources.
You can use Web Control functions to change the settings in the projector's configuration menu.
If there are certain control actions which are carried out regularly at particular times or on particular days, you can use Timer Settings to register timer settings.
• Mail Notification settings
You can set e-mail addresses to which notifications are sent if a status that requires attention, such as a problem, occurs with a registered projector.
• Sending messages to registered projectors
You can use the Message Broadcasting plugin for EasyMP Monitor to send JPEG files to registered projectors.
Download the Message Broadcasting plugin from the Web site address provided at the beginning of this chapter.
Changing Settings Using a Web Browser (Web
Control)
By using the Web browser of a computer connected to the projector on a network, you can set the projector's functions and control the projector.
This function allows you to perform setup and control operations remotely.
In addition, since you can use the computer's keyboard, entering characters required for the setup is easier.
Use Microsoft Internet Explorer 6.0 or later as the Web browser. Use Safari for Mac OS X.
a
If you set Standby Mode to Communication On, you can use a Web browser to make settings and perform control even if the projector is in standby mode (when the power is off).
s Extended - Standby Setup - Standby Mode
Projector setup
In a Web browser, you can set items that are usually set in the projector's
Configuration menu. The settings are reflected in the Configuration menu.
There are also items that can only be set in a Web browser.
Monitoring and Controlling
85
Items in the Configuration menu that cannot be set by a Web browser
• Settings menu - Keystone - Quick Corner
• Settings menu - Image Shift
• Settings menu - Pointer Shape
• Settings menu - Pattern (except Pattern Type)
• Settings menu - User Button
• Extended menu - User's Logo
• Extended menu - USB Type B
• Extended menu - Easy Interactive Function
• Extended menu - Language
• Extended menu - Operation - High Altitude Mode
• Reset menu - Reset All and Reset Lamp Hours
The settings for items on each menu are the same as the projector's
Configuration menu.
s
Items that can only be set with a Web browser
• SNMP Community Name
• Monitor Password b Enter the IP address of the projector in the address input box of the Web browser, and press the Enter key on the computer's keyboard.
c The user ID and password entry screen is displayed.
Enter "EPSONWEB" as the user ID.
The default password is "admin".
a • Enter the user ID even if the password setting is disabled. The user ID cannot be changed.
• You can change the password from Basic - Web Control
Password in the Network menu under the Configuration menu.
s
Displaying the Web Control screen
Use the following procedure to display the Web Control screen.
Make sure the computer and projector are connected to the network. Use
Advanced when connecting via a Wireless LAN.
a
If your Web browser is set up to connect via a proxy server, the Web
Control screen cannot be displayed. To display Web Control, you need to make settings so that a proxy server is not used for a connection.
a Start a Web browser on the computer.
Displaying the Web Remote screen
The Web Remote function allows you to perform projector remote control operations with a Web browser.
a b
Display the Web Control screen.
Click Web Remote.
c The Web Remote screen is displayed.
Monitoring and Controlling
Name
A [t] button
B [Computer] button
C
D
E
[Video] button
[Freeze] button
[A/V Mute] button
Function
Turns the projector power on or off.
s
"From Installation to Projection" p.39
Each time the button is pressed, it cycles through the following images:
• Computer1 port
• Computer2 port
Each time the button is pressed, it cycles through the following images:
• S-Video port
• Video port
• HDMI port
Pauses or resumes image playback.
s
"Freezing the Image (Freeze)" p.67
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
86
F [Page] buttons
G
H
I
Name
[Up] [Down]
[Source Search] button
[LAN] button
[USB] button
J [Volume] buttons
[a][b]
Function
Changes pages in files such as PowerPoint files when using the following projection methods.
• When using the Wireless Mouse function s
"Using the Remote Control to Operate the
Mouse Pointer (Wireless Mouse)" p.70
• When using USB Display s
"Projecting with USB Display" p.41
• When connecting to a network
When projecting images using Slideshow, pressing these buttons displays the previous/next image file.
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
Changes to the images projected with EasyMP Network
Projection. When projecting using the optional Quick
Wireless Connection USB Key, this button switches to that image.
s
"Switching to the Target Image Using the Remote
Each time the button is pressed, it cycles through the following images:
• USB Display
• Images from the device connected to the USB-A port s
"Switching to the Target Image Using the Remote
[a] Decreases the volume.
[b] Increases the volume.
s
Monitoring and Controlling
87
Using the Mail Notification Function to Report
Problems
When you set Mail Notification, notification messages are sent to the preset email addresses when a problem or warning occurs with a projector. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.
s Network - Mail - Mail Notification
a • Up to a maximum of three notification destinations (addresses) can be registered, and notification messages can be sent to all three destinations at once.
• If a projector develops a critical problem and suddenly stops working, it may not be able to send a message notifying an operator of the problem.
• Controlling is possible if Standby Mode is set to Communication
On , even if the projector is in standby state (when the power is off).
s Extended - Standby Setup - Standby Mode
The details of the problem are listed line by line. The main message contents are listed below.
• Internal error
• Fan related error
• Sensor error
• Lamp timer failure
• Lamp out
• Internal temperature error
• High-speed cooling in progress
• Lamp replacement notification
• No-signal
No Signal is input to the projector. Check the connection status or check that the power for the signal source is turned on.
• Auto Iris Error
• Power Err. (Ballast)
• Obstacle Detection Error
See the following to deal with problems or warnings.
s
"Reading the Indicators" p.118
Reading Error Notification Mail
When the Mail Notification function is set to On and a problem or warning occurs in the projector, the following email will be sent.
Sender: Email Address 1
Subject: EPSON Projector
Line 1: The name of the projector where the problem occurred
Line 2: The IP address set for the projector where the problem has occurred.
Line 3 and on: Details of the problem
Management Using SNMP
By setting SNMP to On in the Configuration menu, notification messages are sent to the specified computer when a problem or warning occurs. This will enable the operator to be notified of problems with projectors even at locations away from the projectors.
s Network - Others - SNMP
Monitoring and Controlling
88 a • SNMP should be managed by a network administrator or someone who is familiar with the network.
• To use the SNMP function to monitor the projector, you need to install the SNMP manager program on your computer.
• The managing function using SNMP cannot be used via wireless
LAN in Quick connection mode.
• Up to two destination IP addresses can be saved.
ESC/VP21 Commands
You can control the projector from an external device using ESC/VP21.
Item
HDMI
Video
S-Video
USB Display
USB
LAN
A/V Mute ON/OFF On
Off
RGB
Component
Command
SOURCE 21
SOURCE 24
SOURCE 30
SOURCE 41
SOURCE 42
SOURCE 51
SOURCE 52
SOURCE 53
MUTE ON
MUTE OFF
Add a Carriage Return (CR) code (0Dh) to the end of each command and transmit.
For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Command list
When the power ON command is transmitted to the projector, the power turns on and it enters warm-up mode. When the projector's power has turned on, a colon ":" (3Ah) is returned.
When a command is input, the projector executes the command and returns a ":", and then accepts the next command.
If the command being processed terminates abnormally, an error message is output and a ":" is returned.
The main contents are listed below.
Power ON/OFF
Signal selection
Item
On
Off
Computer1
Computer2
Auto
RGB
Component
Auto
Command
PWR ON
PWR OFF
SOURCE 1F
SOURCE 11
SOURCE 14
SOURCE 2F
Cable layouts
Serial connection
• Connector shape: D-Sub 9-pin (male)
Monitoring and Controlling
• Projector input port name: RS-232C
<At the projector>
<At the projector>
Signal Name
GND
TD
RD
Function
Signal wire ground
Transmit data
Receive data
Communications protocol
• Default baud rate setting: 9600 bps
• Data length: 8 bit
• Parity: None
• Stop-bit: 1 bit
• Flow control: None
89
<At the computer>
(PC serial cable) <At the computer>
About PJLink
PJLink Class1 was established by the JBMIA (Japan Business Machine and
Information System Industries Association) as a standard protocol for controlling network-compatible projector's as part of their efforts to standardize projector control protocols.
The projector complies with the PJLink Class1 standard established by the
JBMIA.
You need to make network settings before you can use PJLink. See the following for more information on network settings.
s
It complies with all commands except for the following commands defined by PJLink Class1, and agreement was confirmed by the PJLink standard adaptability verification.
URL: http://pjlink.jbmia.or.jp/english/
• Non-compatible commands
Mute settings
Function
Image muting set
Audio muting set
PJLink Command
AVMT 11
AVMT 21
• Input names defined by PJLink and corresponding projector sources
Source PJLink Command
Computer1
Computer2
Video
S-Video
HDMI
USB
INPT 11
INPT 12
INPT 21
INPT 22
INPT 32
INPT 41
Monitoring and Controlling
90
LAN
USB Display
Source
INPT 52
INPT 53
PJLink Command
• Manufacturer name displayed for "Manufacture name information query"
EPSON
• Model name displayed for "Product name information query"
EB-485Wi/EB-485WT/EB-CU610Wi/BrightLink 485Wi
EB-485W/EB-CU610W/PowerLite 485W
EB-480i/EB-480T/EB-CU610Xi/BrightLink 480i
EB-480/EB-CU610X/PowerLite 480
EB-475Wi/EB-475WT/EB-CU600Wi/BrightLink 475Wi
EB-475W/EB-CU600W/PowerLite 475W
EB-470/EB-CU600X/PowerLite 470
• Monitoring and control with application software
You can use Crestron RoomView ® Express or Crestron RoomView ®
Server Edition provided by Crestron ® to monitor devices in the system, to communicate with the help desk, and to send emergency messages. See the following Web site for details.
http://www.crestron.com/getroomview
This manual describes how to perform operations on your computer using a Web browser.
a • You can only enter single-byte alphanumeric characters and symbols.
• The following functions cannot be used while using Crestron
RoomView ® .
s
"Changing Settings Using a Web Browser (Web Control)" p.84
Message Broadcasting (EasyMP Monitor plug-in)
• Controlling is possible if Standby Mode is set to Communication
On , even if the projector is in standby state (when the power is off).
s Extended - Standby Setup - Standby Mode
About Crestron RoomView
®
Crestron RoomView ® is an integrated control system provided by
Crestron ® . It can be used to monitor and control multiple devices connected on a network.
The projector supports the control protocol, and can therefore be used in a system built with Crestron RoomView ® .
Visit the Crestron ® Web site for details on Crestron RoomView ® . (Only
English-language displays are supported.) http://www.crestron.com
The following provides an overview of Crestron RoomView ® .
• Remote operation using a Web browser
You can operate a projector from your computer just like using a remote control.
Operating a projector from your computer
Displaying the operation window
Check the following before carrying out any operations.
• Make sure the computer and projector are connected to the network.
When communicating with a wireless LAN, connect in Advanced connection mode.
s
• Set Crestron RoomView to On from the Network menu.
s
Network - Others - Crestron RoomView
Monitoring and Controlling a b
Start a Web browser on the computer.
Enter the IP address of the projector in the address field of the
Web browser, and press the Enter key on the keyboard.
The operation window is displayed.
Using the operation window
A You can perform the following operations when you click the buttons.
Power
Button
Vol-/Vol+
Function
Turns the projector power on or off.
Adjusts the volume.
91
A/V Mute
Freeze
Button
Contrast
Button
Brightness
Color
Sharpness
Zoom
Function
Turns the video and audio on or off.
s
"Hiding the Image and Sound Temporarily (A/V
B Switch to the image from the selected input source. To display input sources that are not shown on the screen, click (a) or (b) to scroll up or down. The current video signal input source is displayed in blue.
You can change the source name if necessary.
C You can perform the following operations when you click the buttons. To display buttons that are not shown on the screen, click (c) or (d) to scroll left or right.
Function
Pauses or resumes image playback.
s
"Freezing the Image (Freeze)" p.67
You can adjust the difference between light and dark in the images.
You can adjust the image brightness.
You can adjust the color saturation for the images.
You can adjust the image sharpness.
Click the [z] button to enlarge the image without changing the projection size. Click the [x] button to reduce an image that was enlarged with the [z] button.
Click the [ ], [ ], [ ], or [ ] button to change the position of an enlarged image.
s
"Enlarging Part of the Image (E-Zoom)" p.69
D
[ ], [ ], [ ], and [ ] buttons have the same effects as [ ], [ and [ ] buttons on the remote control respectively. You can perform the following operations when you click the other buttons.
], [ ],
Monitoring and Controlling
OK
Menu
Auto
Search
Esc
Button Function
Performs the same operation as the [ ] button on the remote control.
s
Displays and closes the Configuration menu.
If clicked while projecting analog RGB signals from
Computer1 port or Computer2 port, automatically optimizes the image by adjusting the Tracking, Sync., and Position.
Switches to the image from the input port where video signals are being input.
s
"Automatically Detect Input Signals and Change the
Projected Image (Source Search)" p.40
Performs the same operation as the [Esc] button on the remote control.
s
E You can perform the following operations when you click the tabs.
Tab
Contact IT Help
Info
Tools
Function
Displays the Help Desk window. Used to send messages to, and receive messages from, the administrator using
Crestron RoomView ® Express.
Displays information on the projector that is currently connected.
Changes settings in the projector that is currently connected. See the next section.
Using the tools window
The following window is displayed when you click the Tools tab on the operation window. You can use this window to change settings in the projector that is currently connected.
92
A Crestron Control
Make settings for Crestron ® central controllers.
B Projector
The following items can be set.
Item
Projector Name
Location
Assigned To
Function
Enter a name to differentiate the projector that is currently connected from other projectors on the network. (The name can contain up to 15 single-byte alphanumeric characters.)
Enter an installation location name for the projector that is currently connected on the network. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
Enter a user name for the projector. (The name can contain up to 32 single-byte alphanumeric characters and symbols.)
Monitoring and Controlling
DHCP
Send
Item
IP Address
Subnet Mask
Default Gateway
Function
Select the Enabled check box to use DHCP. You cannot enter an IP address if DHCP is enabled.
Enter the IP address to assign to the currently connected projector.
Enter a subnet mask for the currently connected projector.
Enter the gateway address for the currently connected projector.
Click this button to confirm the changes made to the
Projector .
C Admin Password
Select the Enabled check box to require a password to open the Tools window.
The following items can be set.
Item
New Password
Confirm
Send
Function
Enter the new password when changing the password to open the Tools window. (The name can contain up to 26 single-byte alphanumeric characters.)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
Admin Password .
D User Password
Select the Enabled check box to require a password to open the operation window on the computer.
The following items can be set.
Item
New Password
Confirm
Send
93
Function
Enter the new password when changing the password to open the operation window. (Up to 26 single-byte alphanumerical characters)
Enter the same password as you entered in New
Password . If the passwords are not the same, an error is displayed.
Click this button to confirm the changes made to the
User Password .
Configuration Menu
This chapter explains how to use the Configuration menu and its functions.
Using the Configuration Menu
This section explains how to use the Configuration menu.
Although steps are explained using the remote control as an example, you can perform the same operations from the control panel. Check the guide under the menu for the available buttons and their operations.
a Display the Configuration menu screen.
c Select a submenu item.
d Change settings.
b Select a top menu item.
e Press the [Menu] button to finish making settings.
95
List of Functions
Configuration Menu Table
Settable items vary depending on the model being used and the image signal and source being projected.
Top Menu Name
Image menu s
Signal menu s
Submenu Name Items or Setting Values
Color Mode
Brightness
Contrast
Color Saturation
Tint
Sharpness
Abs. Color Temp.
Color Adjustment
Dynamic, Presentation, Theatre,
Photo, Sports, sRGB, Blackboard, and Whiteboard
-24 to 24
-24 to 24
-32 to 32
-32 to 32
-5 to 5
5000K to 10000K
Red: -16 to 16
Green: -16 to 16
Blue: -16 to 16
Auto Iris
Auto Setup
Resolution
Tracking
Sync.
Position
Progressive
Noise Reduction
On and Off
On and Off
-
-
Auto, Wide, and Normal
Up, Down, Left, and Right
Off, Video, and Film/Auto
Off, NR1, and NR2
HDMI Video Range Auto, Normal, and Expanded
Input Signal Auto, RGB, and Component
96
Top Menu Name
Settings menu s
Extended menu s
Submenu Name
Video Signal
Aspect
Overscan
Keystone
Zoom
Image Shift -
Items or Setting Values
Auto, NTSC, NTSC4.43, PAL,
M-PAL, N-PAL, PAL60, and
SECAM
Normal, Auto, 4:3, 16:9, Full,
Zoom, and Native
Auto, Off, 4%, and 8%
H/V-Keystone and Quick Corner
0 (Wide) to 40 (Tele)
Control Panel Lock
Pointer Shape
Full Lock, Partial Lock, and Off
Pointer 1, Pointer 2, Pointer 3
Power Consumption Normal and ECO
Volume 0 to 20
Mic Input Level
Remote Receiver
User Button
Pattern
Display
User's Logo
Projection
Operation
0 to 5
Front/Rear, Front, Rear and Off
Power Consumption, Info,
Progressive, Test Pattern,
Resolution, Mic Input Level,
Pattern Display, Auto
Calibration
-
Pattern Display, Pattern Type,
User Pattern, and Test Pattern
Messages, Display Background,
Startup Screen, and A/V Mute
Front, Front/Upside Down, Rear,
Rear/Upside Down
Direct Power On, Sleep Mode,
Sleep Mode Timer, High
Altitude Mode, and Audio Input
List of Functions
97
Top Menu Name Submenu Name
Standby Setup
USB Type B
Easy Interactive Func‐ tion
-
-
-
-
-
-
-
-
-
-
Items or Setting Values
Standby Mode, Standby
Microphone, Standby Audio
-
-
Easy Interactive Function, USB
Display/Easy Interactive
Function, Wireless Mouse/USB
Display
Auto Calibration, Manual
Calibration, Use Source, Number of Pen Users, Pen Operation
Mode, Enable Right Click,
Advanced
15 or 35 languages *
Info menu s
Reset menu s
Language
Lamp Hours
Source
Input Signal
Resolution
Video Signal
Refresh Rate
Sync Info
Status
Serial Number
Event ID
Reset All
Reset Lamp Hours
* The number of supported languages differs depending on the region where the projector is used.
Network menu
Top Menu Name
Basic menu s
Wireless LAN menu s
Security menu s
Wired LAN menu s
Submenu Name
Projector Name
PJLink Password
Web Control Password -
-
-
Projector Keyword
Wireless LAN Power
Items or Setting Values
On and Off
On and Off
Connection Mode
Channel
Wireless LAN Sys.
SSID Auto Setting
SSID
IP Settings
-
Quick and Advanced
1ch, 6ch, and 11ch
802.11b/g and 802.11b/g/n
On and Off
DHCP, IP Address, Subnet Mask, and Gateway Address
SSID Display
IP Address Display
Security
WEP Encryption
Format
Key ID
Encryption Key 1, En‐ cryption Key 2, Encryp‐ tion Key 3, and Encryp‐ tion Key 4
Authentication Type
PSK
IP Settings
-
On and Off
On and Off
No, WEP, WPA-PSK, and WPA2-
PSK
128Bit and 64Bit
ASCII and HEX
-
1, 2, 3, 4
Open and Shared
DHCP, IP Address, Subnet Mask, and Gateway Address
List of Functions
Top Menu Name
Mail menu s
Others menu s
Submenu Name
IP Address Display
Mail Notification
SMTP Server
Port Number
Address 1 Setting, Ad‐ dress 2 Setting, and Ad‐ dress 3 Setting
SNMP
Trap IP Address 1 and
Trap IP Address 2
-
-
-
-
Items or Setting Values
On and Off
On and Off
On and Off
Priority Gateway Wired LAN and Wireless LAN
AMX Device Discovery On and Off
Crestron RoomView
Bonjour
On and Off
On and Off
Image Menu
Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.
98 s
"Automatically Detect Input Signals and Change the Projected Image
Sub-menu Function
Color Mode
Brightness
Contrast
You can select the quality of the image to suit your surroundings.
s
"Selecting the Projection Quality (Selecting Color Mode)" p.51
You can adjust the image brightness.
You can adjust the difference between light and dark in the images.
Color Saturation (Adjustment is only possible when component video, composite video, or S-video images are being input.)
You can adjust the color saturation for the images.
Tint
Sharpness
(Adjustment is possible when component video signals are being input. Composite video and S-video input signals can only be adjusted when they are NTSC video signals.)
You can adjust the image tint.
You can adjust the image sharpness.
List of Functions
99
Sub-menu
Color Adjust‐ ment
Function
Abs. Color Temp.
(This item cannot be selected if Color Mode is set to sRGB
You can adjust the overall tint of the image. You can adjust tints in 10 stages from 5000 K to 10000 K. The image is tinted blue when a high value is selected and tinted red when a low value is selected.
(This item cannot be selected if Color Mode is set to sRGB
You can adjust the color strength for Red, Green, and Blue individually.
Auto Iris (This item can be set only if Color Mode is set to Dynamic or
Theatre .)
Set to On to adjust the iris to obtain the optimum light for images being projected.
The setting is stored for each Color Mode.
s
Reset You can reset all adjustment values for the Image menu to their default settings. See the following to return all menu items to their default settings.
s
Signal Menu
Settable items vary depending on the image signal and source currently being projected. Setting details are saved for each image signal.
You cannot make settings on the Signal menu when the source is USB
Display, USB, or LAN.
s
"Automatically Detect Input Signals and Change the Projected Image
Sub-menu
Auto Setup
Function
(Only available when analog RGB computer signals are being input.)
Set to On to automatically adjust Tracking, Sync., and Position to the optimum state when the input signal changes.
List of Functions
Sub-menu
Resolution
Tracking
Sync.
Position
Progressive
Function
(Only available when analog RGB computer signals are being input.)
Set to Auto to automatically identify the resolution of the input signal. If images are not projected correctly when set to Auto, for example if some of the image is missing, adjust to Wide for wide screens, or set to Normal for 4:3 or 5:4 screens depending on the connected computer.
(Only available when analog RGB computer signals are being input.)
You can adjust computer images when vertical stripes appear in the images.
(Only available when analog RGB computer signals are being input.)
You can adjust computer images when flickering, fuzziness, or interference appear in the images.
(This item cannot be set when the source is HDMI.)
You can adjust the display position up, down, left, and right when a part of the image is missing so that all of the image is projected.
(This setting can only be adjusted when composite video or svideo signals are being input. When component video or RGB video signals are being input, this setting can only be adjusted if the signals being input are interlaced signals (480i/576i/1080i).)
Interlace
(i) signal is converted to Progressive
conversion)
Off : Ideal for images with a large amount of movement.
Video : Ideal for general video images.
Film/Auto : This is ideal for movie films, computer graphics, and animation.
100
Sub-menu
HDMI Video
Range
Function
Noise Reduction (This cannot be set when a digital RGB signal is input, or when an interlace signal is being displayed when Progressive is set to
Off .)
Smoothes out rough images. There are two modes. Select your favorite setting. It is recommended that this is set to Off when viewing image sources in which noise is very low, such as for
DVDs.
When the projector's HDMI port is connected to a DVD player, the projector's video range is set according to the DVD player's video range setting.
Input Signal You can select the input signal from the Computer1 port or the
Computer2 port.
If set to Auto, the input signal is set automatically according to the connected equipment.
If colors do not appear correctly when set to Auto, select the appropriate signal according to the connected equipment.
Video Signal
Aspect
Overscan
You can select the input signal from the S-Video port or the
Video port. If set to Auto, video signals are recognized automatically. If interference appears in the image or a problem occurs such as no image is being projected when set to Auto, select the appropriate signal according to the connected equipment.
You can set the aspect ratio
for projected images.
s
"Changing the Aspect Ratio of the Projected Image" p.52
(This setting can only be adjusted when component video or
RGB video signals are being input.)
Changes the output image ratio (the range of the projected image). You can set the cropping range to Off, 4%, or 8%. When the source is HDMI, Auto is available. When Auto is selected, it automatically changes to Off or 8% according to the input signal.
List of Functions
Sub-menu
Reset
Function
You can reset all adjustment values on the Signal menu to their default settings, except for Input Signal.
See the following to return all menu items to their default settings.
s
Settings Menu
Sub-menu
Keystone
Zoom
Function
You can correct keystone distortion.
• When H/V-Keystone is selected:
Adjust V-Keystone and H-Keystone to correct horizontal and vertical keystone distortion.
• When Quick Corner is selected:
Select and correct the four corners of the projected image.
s
Adjusts the projected image size.
101
Sub-menu
Image Shift
Control Panel
Lock
Pointer Shape
Function
Starts Image Shift.
s
"Adjusting the Position of the Image (Image Shift)" p.48
You can use this to restrict operation of the projector's control panel.
s
"Restricting Operation (Control Panel Lock)" p.82
You can select the shape of the pointer.
Pointer 1:
Pointer 2:
Power Consump‐ tion
Volume
Pointer 3: s
"Pointer Function (Pointer)" p.68
You can set the lamp brightness to one of two settings.
Select ECO if the images being projected are too bright, such as when projecting images in a dark room or onto a small screen.
When ECO is selected, the amount of electricity consumed and the lamp's operating life are changed as follows, and fan rotation noise during projection is reduced.
Electrical consumption: Approx. 35% decrease, lamp life:
Approx. 1.3 times longer
You can adjust the volume. Setting values are saved for each source.
Mic Input Level Adjust this if the microphone input level is low and the microphone audio output from the projector's speaker is difficult to hear, or if the input level is too high, resulting in a crackling sound in the audio from the microphone. When Mic Input Level is turned down to 0, no microphone audio is output from the speaker.
When the microphone input level is raised, the audio from the connected device becomes quieter. When the microphone input level is lowered, the audio from the connected device becomes louder.
List of Functions
Sub-menu Function
Remote Receiver You can limit the reception of the operation signal from the remote control.
When set to Off, you cannot perform any operations from the remote control. If you want to make operations from the remote control, hold down the [Menu] button on the remote control for at least 15 seconds to reset the setting to its default value.
User Button You can select the item in the Configuration menu to be assigned to the [User] button on the remote control. By pressing the [User] button the assigned menu item selection/adjustment screen is displayed, allowing you to make one-touch settings/ adjustments. You can assign one of the following items to the [User] button.
Power Consumption , Info, Progressive, Test Pattern,
Resolution , Mic Input Level, Pattern Display, Auto
Calibration (EB-485Wi/EB-480i/EB-475Wi only)
102
Sub-menu
Pattern
Function
Pattern Display : Display a pattern.
Pattern Type : You can select from Patterns 1 to 4 or User
Pattern. Patterns 1 to 4 display projection lines such as ruled lines or a grid.
Pattern 2: Pattern 1:
Pattern 3: Pattern 4:
Reset
User Pattern : Captures a user pattern.
s
Test Pattern : When the projector is set up, a test pattern is displayed so that you can adjust the projection status without connecting equipment. While the test pattern is displayed, zoom, focus adjustments, and keystone correction can be performed.
To cancel the Test Pattern, press the [Esc] button on the remote control or the control panel.
Attention
If a pattern is displayed for a long time, a residual image may be visible in projected images.
You can reset all adjustment values in the Settings menu to their default settings, except for Zoom and User Button.
See the following to return all menu items to their default settings.
s
List of Functions
Extended Menu
Sub-menu
Display
User's Logo *1
Function
You can make settings related to the projector's display.
Messages : When set to Off, the following items will not be displayed.
Item names when the Source, Color Mode, or Aspect Ratio is changed, messages when no signal is being input, and warnings such as High Temp Warning.
Display Background * 1 : You can set the screen status for when no image signal is available to Black, Blue, or
Logo .
Startup Screen * 1 : Set to On to display the User's Logo when projection starts.
A/V Mute * 1 : You can set the screen displayed when the remote control's [A/V Mute] button is pressed to Black,
Blue , or Logo.
You can change the user's logo that is displayed as a background during Display Background, A/V Mute, and so on.
s
103
Sub-menu
Projection
Operation
Function
Select from one of the following projection methods depending on how the projector is installed.
Front , Front/Upside Down, Rear, Rear/Upside Down
You can change the Projection setting as follows by holding down the [A/V Mute] button on the remote control for about five seconds.
FrontWFront/Upside Down
RearWRear/Upside Down s
Direct Power On : Set to On to turn on the projector simply by plugging it in.
When the power cord is plugged in, note that the projector turns on automatically in cases such as a power outage being restored.
Sleep Mode : When this is set to On, the power is turned off automatically when no image signal is input and no operation is performed within a certain amount of time.
Sleep Mode Timer : When Sleep Mode is set to On, you can set the time before the projector automatically turns off within a range of 1 to 30 minutes.
High Altitude Mode : Set this to On when using the projector at an altitude of 1500 m or above.
Audio Input : When set to Auto, the audio from the input source is output.
When set to Audio1, Audio2, or Audio (L/R), the audio from the selected input source is output.
List of Functions
Sub-menu Function
Standby Setup Standby Mode : When set to Communication On, you can perform the following operations even if the projector is in standby mode.
• Monitoring and controlling the projector over the network.
s
"Monitoring and Controlling" p.84
• Outputting analog RGB signals from the Computer1 port to an external monitor.
• Outputting audio from the microphone to the projector's speaker.
(Only when the Standby Microphone is set to On.) s
"Connecting Image Sources" p.28
• Outputting audio from the input port to an external speaker.
(Only when Standby Audio is set to On.)
Audio input from HDMI, USB Display, USB, or LAN cannot be output.
Also, audio is not output when Audio Input is set to
Auto and the previous source that was being used is
HDMI, USB Display, USB, or LAN.
s
"Connecting Image Sources" p.28
• Mixing audio from the microphone and the input port, and outputting audio to an external speaker.
(Only when both Standby Microphone and Standby
Audio are set to On.) s
"Connecting Image Sources" p.28
Standby Microphone : When set to On, you can output audio from the microphone to the projector's speaker even if the projector is in standby mode. (Only available when
Standby Mode is set to Communication On.)
Standby Audio : When set to On you can output audio from the audio in port to an external speaker even if the projector is in standby mode. (Only available when Standby
Mode is set to Communication On.)
104
Sub-menu
USB Type B
(EB-485Wi/
EB-480i/
EB-475Wi only)
Function
Easy Interactive Function : Allows you to use the Easy
Interactive Function (Computer Interactive). USB Display and Wireless Mouse functions are not available.
USB Display/Easy Interactive Function : Allows you to use the Easy Interactive Function (Computer Interactive) and
USB Display. The Wireless Mouse function is not available.
Wireless Mouse/USB Display : Allows you to use the
Wireless Mouse function and USB Display. The Easy
Interactive Function (Computer Interactive) is not available.
s
"Projecting with USB Display" p.41
s
"Using the Remote Control to Operate the Mouse
Pointer (Wireless Mouse)" p.70
s
"Easy Interactive Function (EB-485Wi/EB-480i/
List of Functions
105
Sub-menu
Easy Interactive
Function
(EB-485Wi/
EB-480i/
EB-475Wi only)
Function
Allows you to use and set the Easy Interactive Function.
s
"Easy Interactive Function (EB-485Wi/EB-480i/
Items in General
• Auto Calibration: Starts Auto Calibration.
• Manual Calibration: Starts Manual Calibration.
Language
Items in Computer Interactive s
• Use Source: Allows you to set the image source for Easy
Interactive Tools and so on.
• Number of Pen Users: Allows you to set the number of people who can use the Easy Interactive Pens at the same time.
• Pen Operation Mode: (Only available when Number of
Pen Users is set to One User)
Allows you to set the Easy Interactive Pen operation mode when using Easy Interactive Tools.
• Enable Right Click: (Only available when Pen Operation
Mode is set to Mouse)
When this is set to On, a long press of the Easy
Interactive Pen acts as a right click.
• Advanced: Includes the following items.
• Pen Tip Button: Allows you to set operations for the pen tip button of the Easy Interactive Pen.
• Auto Adjust Pen Area: When this is set to On, the pen area is automatically adjusted as the resolution for the connected computer changes.
• Manual Adj. Pen Area: Starts Manual Adj. Pen Area.
Allows you to set the language for messages and menus.
Sub-menu
Reset
Function
You can reset the adjustment values for Display * 1 and
Operation * 2 from the Extended menu to their default settings.
See the following to return all menu items to their default settings.
s
* 1 When User's Logo Protect is set to On in Password Protect, settings related to user's logo cannot be changed. You can make changes after setting User's
Logo Protect to Off.
s
"Managing Users (Password Protect)" p.80
* 2 Except for High Altitude Mode.
Network Menu
When Network Protect is set to On in Password Protect, a message is displayed and the network settings cannot be changed. Turn Network
Protect Off and then configure the network.
s
"Setting Password Protect" p.80
List of Functions
106
Sub-menu
Net. Info. - Wire‐ less LAN
Net. Info. -
Wired LAN
Network Config‐ uration
Function
Displays the following network setting status information.
• Connection Mode
• Antenna Level
• Projector Name
• SSID
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
• Region Code *
Displays the following network setting status information.
• Projector Name
• DHCP
• IP Address
• Subnet Mask
• Gateway Address
• MAC Address
The following menus are available for setting network items.
Basic , Wireless LAN, Security, Wired LAN, Mail, Others,
Reset , and Setup complete
* Displays available region information for the Wireless LAN unit being used.
For more details, contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List a
By using a Web browser of a computer connected to the projector on a network, you can set functions and control the projector. This function is called Web Control. You can easily enter text using a keyboard to make settings for Web Control such as Security settings.
s
"Changing Settings Using a Web Browser (Web Control)" p.84
Notes on operating the Network menu
Selecting from the top menu and sub menus, and changing selected items is the same as making operations from the Configuration menu.
When done, make sure you go to the Setup complete menu, and select one of Yes, No, or Cancel. When you select Yes or No, you return to the
Configuration menu.
Yes : Saves the settings and exits the Network menu.
No : Does not save the settings and exits the Network menu.
Cancel : Continues displaying the Network menu.
Soft keyboard operations
The Network menu contains items that require input of alphanumerics during setup. In this case, the following software keyboard is displayed. Use the [ ], [ ], [ ], and[ ] buttons on the remote control or the [ w ], [ v ], [Wide], and [Tele] buttons on the control panel to move the cursor to the key you want, and then press the [ ] button to enter the alphanumerical character. Enter figures by holding down the [Num] button on the remote control, and pressing the numeric buttons. After inputting, press Finish on the keyboard to confirm your input. Press Cancel on the keyboard to cancel your input.
List of Functions
107
Basic menu
• Each time the CAPS key is selected and the [ ] button is pressed, it switches between upper case and lower case.
• Each time the SYM1/2 key is selected and the [ ] button is pressed, it sets and changes the symbol keys for the section enclosed by the frame.
Sub-menu Function
Projector Name Displays the projector name used to identify the projector when connected to a network.
When editing, you can enter up to 16 single-byte alphanumeric characters.
PJLink Password Set a password to use when you access the projector using compatible PJLink software.
You can enter up to 32 single-byte alphanumeric characters.
Web Control
Password
Set a password to use when making settings and controlling the projector using Web Control. Enter no more than eight singlebyte alphanumeric characters. The default password is "admin".
Web Control is a computer function that allows you to set up and control the projector by using the Web browser on a computer connected on a Network.
s
"Changing Settings Using a Web Browser (Web Control)" p.84
List of Functions
Sub-menu
Projector Key‐ word
Function
When set to On, you have to enter the keyword when you try to connect the projector to a computer via a network. As a result, you can prevent presentations from being interrupted by connections from other computers.
Normally this should be set to On.
s EasyMP Network Projection Operation Guide
Wireless LAN menu
108
Sub-menu
Connection
Mode
Channel
Wireless LAN
Sys.
SSID Auto Set‐ ting
SSID
Function
Set the connection mode when using EasyMP Network
Projection to connect the projector and computer.
This is set to Quick by default.
See the following manual for details on Connection Mode.
s EasyMP Network Projection Operation Guide
(This can only be set if Connection Mode is set to Quick.)
Select the frequency band used by the wireless LAN from 1ch,
6ch , or 11ch.
This is set to 11ch by default.
Set the Wireless LAN Sys. to either 802.11b/g or 802.11b/g/n.
The default value is 802.11b/g/n.
(This can only be set if Connection Mode is set to Quick.)
Set to On to speed up the projector search.
Set to Off when connecting to multiple projectors at the same time.
This is set to On by default.
(This can be set only if SSID Auto Setting is set to Off.)
Enter an SSID
g . When an SSID is provided for the wireless LAN
system in which the projector participates, enter the SSID.
You can enter up to 32 single-byte alphanumeric characters.
Sub-menu
Wireless LAN
Power
Function
Turn On when connecting the projector to the computer over wireless LAN.
If you do not want to connect via wireless LAN, turn it Off to prevent unauthorized access by others.
This is set to On by default.
List of Functions
109
Sub-menu
IP Settings
SSID Display
IP Address Dis‐ play
Function
(This can be set only if Connection Mode is set to Advanced.)
You can make network settings.
DHCP : Set to On to make network settings using DHCP
is set to On, you cannot set any more addresses.
IP Address
: You can input the IP address g assigned to the
projector. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet Mask : You can input the subnet mask
You can enter a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address : You can input the IP address for the gateway for the projector. You can enter a number from 0 to 255 in each field of the address. However, the following Gateway addresses
cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
To prevent the SSID
g from being displayed on the LAN Standby
screen, set this to Off.
To prevent the IP address
g from being displayed on the LAN
Standby screen, set this to Off.
Security menu
Sub-menu
Security
Function
Select the security type from the items that are displayed.
When setting security, follow the instructions from the administrator of the network system you are about to access.
WEP Encryption You can set the encryption method for WEP encryption.
128Bit : Uses 128 (104) bit encoding.
64Bit : Uses 64 (40) bit encoding.
Format
Key ID
You can set the input method for the WEP encryption key to
ASCII or HEX.
You can select the WEP encryption ID key.
List of Functions
Sub-menu
Encryption Key
1/Encryption Key
2/Encryption Key
3/Encryption Key
4
Authentication
Type
PSK
Function
You can enter the key used for WEP encryption. Enter the key in single-byte characters following instructions from the network administrator for the network in which the projector participates. The type of character and the number that can be entered differ according to the WEP Encryption and Format settings.
128Bit - ASCII: Single-byte alphanumerics, 13 characters.
64Bit - ASCII: Single-byte alphanumerics, 5 characters.
128Bit - HEX: 0 to 9 and A to F, 26 characters.
64Bit - HEX: 0 to 9 and A to F, 10 characters.
Set the WEP authentication type.
Open : Uses open system authentication.
Shared : Uses shared key authentication.
(This can only be set when WPA-PSK or WPA2-PSK are selected from Security.)
You can enter a Pre-Shared Key (encrypted key) in single-byte alphanumeric characters. Enter at least 8 and up to 32 characters.
Type of security
When the optional wireless LAN unit is installed and being used in
Advanced connection mode, it is strongly recommended that you set security. Select one of the following security methods.
• WEP
Data is encrypted with a code key (WEP key). This mechanism prevents communication unless the encryption keys for the access point and the projector match.
110
• WPA
This is an encryption standard that improves security which is a weak point of WEP. Although there are multiple kinds of WPA encryption methods, this projector uses TKIP and AES.
WPA also includes user authentication functions. WPA authentication provides two methods: using an authentication server, or authenticating between a computer and an access point without using a server. This projector supports the latter method, without a server.
a
For setting details, follow the directions from the network administrator of your network.
List of Functions
Wired LAN menu
111
Sub-menu
IP Settings
IP Address Dis‐ play
Function
You can make settings related to the following addresses.
DHCP
g : Set to On to configure the network using DHCP. If this
is set to On, you cannot set any more addresses.
IP Address
g : You can input the IP address assigned to the
projector. You can input a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Subnet Mask
g : You can input the subnet mask for the projector.
You can input a number from 0 to 255 in each field of the address.
However, the following subnet masks cannot be used.
0.0.0.0, 255.255.255.255
Gateway Address g : You can input the IP address for the gateway
for the projector. You can input a number from 0 to 255 in each field of the address. However, the following gateway addresses cannot be used.
0.0.0.0, 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
To prevent the IP address from being displayed on Network Info in the Network menu and on the LAN Standby screen, set this to
Off .
Mail menu
When this is set, you receive an email notification if a problem or warning occurs in the projector.
List of Functions s
"Using the Mail Notification Function to Report Problems" p.87
112
Sub-menu
Address 1 Set‐ ting/Address 2
Setting/Address
3 Setting
Function
You can input the email address of the destination to send the notification email to. You can register up to three destinations.
You can enter up to 32 single-byte alphanumeric characters for the email addresses.
The address for destination 1 is the mail notification sender's address.
You can select the problems or warnings to be notified about by email. When the selected problem or warning occurs in the projector, an email is sent to the specified destination address notifying that a problem or warning has occurred. You can select multiple items from the displayed items.
Sub-menu
Port Number
Function
Mail Notification Set to On to send an email to the preset addresses when a problem or warning occurs with a projector.
SMTP Server You can input the IP address
for the SMTP server for the projector.
You can enter a number from 0 to 255 in each field of the address.
However, the following IP addresses cannot be used.
127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from
0 to 255)
You can input the port number for the SMTP server. The default value is 25. You can input numbers between 1 to 65535.
List of Functions
Others menu
Sub-menu
SNMP
Trap IP Address
1/Trap IP Ad‐ dress 2
Function
Set to On to monitor the projector using SNMP.
To monitor the projector, you need to install the SNMP manager program on your computer. SNMP should be managed by a network administrator.
The default value is Off.
You can register up to two IP addresses for the SNMP trap notification destination. You can enter a number from 0 to 255 in each field of the address. However, the following IP addresses cannot be used. 127.x.x.x, 224.0.0.0 to 255.255.255.255 (where x is a number from 0 to 255)
Priority Gateway You can set the priority gateway to a Wired LAN or Wireless
LAN .
AMX Device Dis‐ covery
When the projector is connected to a network, set this to On to
allow the projector to be detected by AMX Device Discovery g
.
Set this to Off if you are not connected to an environment controlled with a controller from AMX or AMX Device
Discovery.
113
Sub-menu
Crestron Room‐
View
Bonjour
Function
Set this to On only when monitoring or controlling the projector over the network using Crestron RoomView ® . Otherwise, set this to Off.
s
"About Crestron RoomView ® " p.90
When this is set to On, the following functions are not available.
• Web control
• Message Broadcasting (EasyMP Monitor Plug-in)
Set this to On when connecting to the network using Bonjour.
See Apple's Web site for more information on the Bonjour service.
http://www.apple.com/
List of Functions
Reset menu
Resets all of the network settings.
114 s
"Automatically Detect Input Signals and Change the Projected Image
Sub-menu
Reset network settings.
Function
To reset all of the Network settings, select Yes.
Info Menu (Display Only)
Lets you check the status of the image signals being projected and the status of the projector. Items that can be displayed vary depending on the source currently being projected. Depending on the model used, some input sources are not supported.
Sub-menu
Lamp Hours
Source
Input Signal
Resolution
Video Signal
Refresh Rate
Sync Info
Function
You can display the cumulative lamp operating time * .
When it reaches the lamp warning time, the characters are displayed in yellow.
You can display the source name for the connected equipment currently being projected.
You can display the content of Input Signal set in the
Signal menu according to the source.
You can display the resolution.
You can display the settings for Video Signal in the Signal menu.
You can display the refresh rate
You can display the image signal Information.
It may be needed if service is required.
List of Functions
Sub-menu
Status
Serial Number
Event ID
Function
This information is about errors that have occurred with the projector.
It may be needed if service is required.
Displays the projector's serial number.
Displays the application error log.
s
* The cumulative use time is displayed as "0H" for the first 10 hours. 10 hours and above is displayed as "10H", "11H", and so on.
Reset Menu
115
Sub-menu
Reset Lamp
Hours
Function
Clears the cumulative lamp hours use time. Reset this when you replace the lamp.
Sub-menu
Reset All
Function
You can reset all items in the Configuration menu to their default settings.
The following items are not reset to their defaults: Input Signal,
Zoom , User's Logo, all items in the Network menu, Lamp
Hours , Language, Password, and Image Shift.
Troubleshooting
This chapter describes how to identify problems and what to do if a problem is found.
Using the Help
If a problem occurs with the projector, the Help screen is displayed to assist you by pressing the Help button. You can solve problems by answering the questions.
a Press the [Help] button.
The Help screen is displayed.
Using Remote Control Using the Control Panel c Confirm the selection.
Using Remote Control Using the Control Panel
117
Questions and solutions are displayed as shown on the screen below.
Press the [Help] button to exit the Help.
b Select a menu item.
a
See the following if the Help function does not provide a solution to the problem.
s
Using Remote Control Using the control panel
Problem Solving
If you are having a problem with the projector, first check the projector's indicators and see "Reading the Indicators".
See the following if the indicators do not show clearly what the problem might be.
s
"When the Indicators Provide No Help" p.122
Reading the Indicators
The projector is provided with the following three indicators that indicate the operating status of the projector.
118
A Power indicator
B Lamp indicator
Indicates the operating status.
Standby condition
When the [t] button is pressed in this condition, projection starts.
Preparing for network monitoring or cool down in progress
All buttons are disabled while the indicator is flashing.
Warming up
Warm-up time is about 30 seconds. After warm-up is complete, the indicator stops flashing.
The [t] button is disabled during warm-up.
Projecting
Indicates the projection lamp status.
Problem Solving
119
C Temp indicator Indicates the internal temperature status.
See the following table for the status of indicators and how to resolve the problems.
If all indicators are off, check that the power cord is connected correctly and that the power is being supplied normally.
Sometimes, when the power cord is unplugged, the [ t ] indicator remains lit for a short period, but this is not an error.
Status Cause
Internal Error
: Lit : Flashing : Off : Varies according to the projector status
Remedy or Status
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
Fan Error
Sensor Error
High Temp Error
(overheating)
Lamp Error
Lamp Failure
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
The lamp turns off automatically and projection stops. Wait for approximately five minutes. After approximately five minutes the projector switches to standby mode, so check the following two points.
• Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it.
s
"Cleaning the Air Filter" p.138
, "Replacing the Air Filter" p.142
If the error continues after checking the points above, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s
Check the following two points.
• Take out the lamp and check whether it is cracked.
s
• Clean the air filter.
s
"Cleaning the Air Filter" p.138
Problem Solving
120
Status Cause
Auto Iris Error
Power Err.
Remedy or Status
If it is not cracked : Reinstall the lamp and turn on the power.
If the error continues : Replace the lamp with a new one and then turn on the power.
If the error continues : Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
If it is cracked : Contact your local dealer or the nearest address provided in the Epson Projector Contact List. (Images cannot be projected until the lamp is replaced.) s Epson Projector Contact List
When using at an altitude of 1500 m or more, set High Altitude Mode to On.
s
Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the
Epson Projector Contact List.
s Epson Projector Contact List
High Temp Warning (This is not an abnormality. However, if the temperature rises too high again, projection stops automatically.)
• Check that the air filter and air exhaust vent are not blocked, and that the projector is not positioned against a wall.
• If the air filter is clogged, clean or replace it.
s
"Cleaning the Air Filter" p.138
, "Replacing the Air Filter" p.142
Replace Lamp
Obstacle Detection Er‐ ror
Replace it with a new lamp.
s
If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may blow increases. Replace it with a new lamp as soon as possible.
A warning sound is output and the message "For safety purposes remove any obstacles blocking the lens." is displayed. The projector will turns off automatically if no action is taken.
• Remove obstacles around the projection window.
• Clean the obstacle sensor if there is no obstacle.
s
"Cleaning the Obstacle Sensor" p.137
If the error continues : Stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
121 a • See the following if the projector is not operating properly, even though the indicators are all showing normal.
s
"When the Indicators Provide No Help" p.122
• If the indicators are in a state not shown in this table, stop using the projector, remove the power plug from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Problem Solving
When the Indicators Provide No Help
If any of the following problems occur and the indicators do not offer a solution, refer to the pages given for each problem.
Problems Relating to Images
• No images appear
Projection does not start, the projection area is completely black, or the projection area is completely blue.
• Moving images are not displayed
Moving images played back from a computer appear black and the images are not projected.
• Projection stops automatically
• The message "Not supported" is displayed
• The message "No Signal" is displayed
• Images are fuzzy, out of focus, or distorted
• Interference or distortion appear in images
• The mouse cursor flickers (only when projecting USB Display)
• The image is truncated (large) or small, or the aspect ratio is not suitable
Only part of the image is displayed, or the height and width ratios of the image are not correct.
• Image colors are not right
The whole image appears purplish or greenish, images are black
& white, or colors appear dull.
• Images appear dark s
s
s
s
s
s
s
s
s
s
s
Problems when Projection Starts
• The projector does not turn on s
Problems Relating to the Easy Interactive Function
• Cannot the projector's built-in drawing function s
• Cannot operate as a mouse and draw by connecting to a computer s
• The message "An error occurred in the Easy Interactive Function." is displayed s
• The Easy Interactive Pen does not work
• The reaction time for the Easy Interactive Pen is slow (only when projecting USB Display)
• The dot does not move to the next position
• The dot moves automatically s s s s
Other Problems
• No sound can be heard or the sound is faint
• No sound can be heard from the microphone
• The remote control does not work
• I want to change the language for messages and menus
• Mail is not received even if an error occurs with the projector
• Image file names are not displayed correctly in Slideshow
• Cannot change settings using a web browser s
s
s
s
s
s
s
122
Problem Solving
123
Problems Relating to Images
No images appear
Did you press the [t] button?
Are all of the indicators off?
Is A/V Mute active?
Check
Are the Configuration menu settings correct?
Is the image to be projected completely black?
(Only when projecting computer images)
Is the image signal format setting correct?
(Only when projecting images from a video source)
Is the USB cable connected correctly?
(Only when projecting USB Display)
Is Windows Media Center displayed in full screen?
(Only when projecting using USB Display or network connection)
Is an application using the Windows DirectX function displayed?
(Only when projecting using USB Display or network connection)
Remedy
Press the [t] button to turn the power on.
The power cord is not connected correctly or power is not being supplied.
Connect the projector's power cord correctly.
s
"From Installation to Projection" p.39
Check the breaker and so on to ensure power is being supplied.
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.67
Reset all of the settings.
s Reset - Reset All
Some input images, such as screen savers, may be completely black.
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal
Check that the USB cable is connected correctly. Reconnect it if it is not connected or not connected properly.
When Windows Media Center is displayed at full screen, you cannot project using USB Display or network connection.
Reduce the screen size.
Applications using the Windows DirectX function may not display images correctly.
Problem Solving
124
Moving images are not displayed (only the moving image portion turns black)
Check
Is the computer's image signal being output to the LCD and the monitor?
(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)
Remedy
Change the image signal from the computer to external output only. Check your computer's documentation, or contact the computer's manufacturer.
Projection stops automatically
Check
Is Sleep Mode set to On?
Remedy
Press the [t] button to turn the power on. If you do not want to use Sleep Mode, change the setting to Off.
s
Extended - Operation - Sleep Mode p.103
The message "Not supported" is displayed
Check
Is the image signal format setting correct?
(Only when projecting images from a video source)
Do the image signal resolution and refresh rate correspond to the mode?
(Only when projecting computer images)
Remedy
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal
See the documentation supplied with the computer for how to change the image signal resolution and refresh rate output from the computer.
s
"Supported Monitor Displays" p.150
The message "No Signal" is displayed
Check
Are the cables connected correctly?
Is the correct port selected?
Remedy
Check that all the cables required for projection are securely connected.
s
"From Installation to Projection" p.39
Change the image by pressing the [Source Search] button on the remote control or the control panel.
s
"Automatically Detect Input Signals and Change the Projected Image (Source Search)" p.40
Problem Solving
125
Check
Is the power of the connected computer or video equipment turned on?
Are the image signals being output to the projector?
(Only when projecting images from a laptop computer or a computer with a built-in LCD screen)
Turn the power on for the equipment.
Remedy
If the image signals are only being output to the computer's LCD monitor or accessory monitor, change the output so that the image signals are also output externally. For some computer models, when the image signals are output externally, they no longer appear on the LCD monitor or accessory monitor.
If the connection is made while the power of the projector or computer is already turned on, the Fn key (Function key) that changes the computer's image signal to external output may not work. Turn the projector and computer off and then back on again.
s
"From Installation to Projection" p.39
s Computer's documentation
Images are fuzzy, out of focus, or distorted
Check
Is the focus adjusted correctly?
Is the projector at the correct distance?
Is the Keystone adjustment value too large?
Is the Aspect Ratio
Has condensation formed on the lens?
Remedy
Move the focus lever to adjust the focus.
s
Is it projecting outside of the recommended projection distance range?
Setup within the recommended range.
s
"Screen Size and Projection Distance" p.147
Lower the projection angle to reduce the amount of Keystone correction.
s
"Adjusting the Vertical Position of the Image (Models Supplied with the Feet Only)" p.49
You can change the Aspect Ratio of the projected image to suit the type, the ratio of height and width, and the resolution of the input signals.
s
"Changing the Aspect Ratio of the Projected Image" p.52
If the projector is suddenly taken from a cold environment to a warm environment, or if sudden ambient temperature changes occur, condensation may form on the surface of the lens, and this may cause the images to appear fuzzy. Set the projector up in the room about one hour before it is used. If condensation forms on the lens, turn the projector off and wait for the condensation to disappear.
Problem Solving
126
Interference or distortion appear in images
Check
Is the image signal format setting correct?
(Only when projecting images from a video source)
Are the cables connected correctly?
Is an extension cable being used?
Is the correct resolution selected?
(Only when projecting computer images)
Are the Sync.
settings adjusted correctly?
(Only when projecting computer images)
Remedy
Change the setting according to the signal for the connected equipment.
s Signal - Video Signal
Check that all the cables required for projection are securely connected.
s
If an extension cable is used, electrical interference may affect the signals. Use the cables supplied with the projector to check if the cables you are using may be causing the problem.
Set the computer so that the signals being output are compatible with the projector.
s
"Supported Monitor Displays" p.150
s Computer's documentation
Press the [Auto] button on the remote control or the [ ] button on the control panel to perform automatic adjustment.
If the images are not adjusted correctly even after performing automatic adjustment, you can also make adjustments from the Configuration menu.
s
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then clear the
Transfer layered window checkbox.
Is Transfer layered window selected?
(Only when projecting USB Display)
The mouse cursor flickers (only when projecting USB Display)
Check Remedy
Is Make the movement of the mouse pointer smooth. selected?
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Make the movement of the mouse pointer smooth.
(Windows 2000 is unavailable.)
Windows Aero becomes unavailable if this is selected in Windows Vista/7.
The image is truncated (large) or small, or the aspect is not suitable
Check
Is a wide-panel computer image being projected?
(Only when projecting computer images)
Remedy
Change the setting according to the signal for the connected equipment.
s Signal - Resolution
Problem Solving
127
Check
Is the image still being enlarged by E-Zoom?
Is the display position adjusted correctly?
Is the computer set for dual display?
(Only when projecting computer images)
Is the correct resolution selected?
(Only when projecting computer images)
Did you adjust the image position after performing Adjust Zoom or
Keystone?
Remedy
Press the [Esc] button on the remote control to cancel E-Zoom.
s
"Enlarging Part of the Image (E-Zoom)" p.69
(Only when projecting analog RGB signals input from the Computer1 or Computer2 port)
Press the [Auto] button on the remote control or the [ ] button on the control panel to adjust the position.
You can also adjust the position from the Configuration menu.
s Signal - Position
If dual display is activated in the Display Properties of the computer's Control Panel, only about half of the image on the computer screen is projected. To display the entire image on the computer screen, turn off the dual display setting.
s Computer video driver documentation
Set the computer so that the signals being output are compatible with the projector.
s
"Supported Monitor Displays" p.150
s Computer's documentation
Perform Image Shift to adjust the image position after performing Adjust Zoom or Keystone.
s
"Adjusting the Position of the Image (Image Shift)" p.48
Image colors are not right
Check
Do the input signal settings match the signals from the connected device?
Is the image Brightness adjusted correctly?
Are the cables connected correctly?
Is the contrast g adjusted correctly?
Remedy
Change the following settings according to the signal for the connected equipment.
• When the image is from a device connected to the Computer1 or Computer2 port.
s Signal - Input Signal
• When the image is from a device connected to the Video or S-Video port.
s Signal - Video Signal
Adjust the Brightness setting from the Configuration menu.
s
Check that all the cables required for projection are securely connected.
s
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast
Problem Solving
128
Check
Is color adjustment set to an appropriate value?
Are the color saturation and tint adjusted correctly?
(Only when projecting images from a video source)
Images appear dark
Check
Is the image brightness set correctly?
Is the contrast g adjusted correctly?
Is it time to replace the lamp?
Remedy
Adjust the Color Adjustment setting from the Configuration menu.
s Image - Color Adjustment
Adjust the Color Saturation and Tint settings from the Configuration menu.
s Image - Color Saturation, Tint
Remedy
Make Brightness and Power Consumption settings from the Configuration menu.
s
s Extended - Power Consumption
Adjust the Contrast setting from the Configuration menu.
s Image - Contrast
When the lamp is nearly ready for replacement, the images become darker and the color quality declines. Replace the lamp with a new one.
s
Problems when Projection Starts
The projector does not turn on
Did you press the [t] button?
Are all of the indicators off?
Check Remedy
Press the [t] button to turn the power on.
The power cord is not connected correctly or power is not being supplied.
Disconnect and then reconnect the power cord.
s
"From Installation to Projection" p.39
Check the breaker and so on to ensure power is being supplied.
Problem Solving
129
Check Remedy
Do the indicators turn on and off when the power cord is touched? There is probably a poor contact in the power cord, or the power cord may be defective. Reinsert the power cord. If this does not solve the problem, stop using the projector, disconnect the power cord from the electrical outlet, and contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Is the Control Panel Lock set to Full Lock?
Press the [t] button on the remote control. If you do not want to use Control Panel Lock, change the setting to Off.
s Settings - Control Panel Lock
Is the remote receiver set correctly?
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver
Problems Relating to the Easy Interactive Function
Cannot the projector's built-in drawing function
Check
Is Extended set correctly?
Has pen calibration been performed correctly?
Remedy
The projector's built-in drawing function is not available if both of the following conditions are met.
• Extended - USB Type B is set to Easy Interactive Function or USB Display/Easy Interactive Function from the configuration menu.
• Images are projected from the source specified in Extended - Easy Interactive Function - Use Source from the configuration menu.
s Extended-Easy Interactive Function
Make sure you perform pen calibration when using the Easy Interactive Pen for the first time so that the projector recognizes the position of the pen correctly.
Also, calibrate the pen again if you notice any discrepancy in positioning.
s
Problem Solving
130
Cannot operate as a mouse and draw by connecting to a computer
Is Extended set correctly?
Check
The projector is not correctly connected to the computer.
If you are using a notebook computer when the battery power is running low, the USB port may stop working and you might not be able to use USB devices.
Remedy
Make the following settings to link with the computer's functions.
• Set Extended - USB Type B to Easy Interactive Function or USB Display/Easy Interactive Function from the configuration menu.
• Set the source where the computer is connected in Extended - Easy Interactive Function - Use Source from the configuration menu.
s Extended - Easy Interactive Function
Check the USB cable connections. You may be able to resolve the problem by disconnecting and then reconnecting the
USB cable.
Connect the computer to a power source.
The message "An error occurred in the Easy Interactive Function." is displayed
Check
An error has occurred in the Easy Interactive Function.
Remedy
Contact the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
The Easy Interactive Pen does not work
Check
There is an obstacle in the signal route between the Easy Interactive
Pen and the projector.
The signal is interfering with other things such as a light source that is emitting infrared rays.
The battery is low.
The surrounding area is too bright.
Remedy
Remove the obstacle. Also, do not block the signal route when standing in front of the projection screen.
Do not use an infrared remote control or infrared microphone in the same room because the Easy Interactive Pen may malfunction. Switch off the interfering device such as a light source that is emitting infrared rays.
Replace the battery.
Do not allow strong light to shine on the projected screen or the projector's Easy Interactive Function receiver.
Problem Solving
131
Check
Has pen calibration been performed correctly?
Remedy
Make sure you perform pen calibration when using the Easy Interactive Pen for the first time so that the projector recognizes the position of the pen correctly.
Also, calibrate the pen again if you notice any discrepancy in positioning.
s
The reaction time for the Easy Interactive Pen is slow (only when projecting USB Display)
Check
Is Windows Aero enabled?
Remedy
The reaction time for the Easy Interactive Pen may be slow when Windows Aero is enabled.
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Disable Windows Aero and improve the tracking of the interactive pen.
(Windows 2000 is unavailable.)
The dot does not move to the next position
Check
Information from the projection screen is not correctly received due to other things, such as a light source that is emitting infrared rays.
Information from the projection screen may not be received correctly if the projector is too close to the screen.
Remedy
Move the device, such as a light source that is emitting infrared rays, away from the projector, or move the projector away from the device.
Check the position of the projector.
The dot moves automatically
Check
The Easy Interactive Pen is disabled due to unstable conditions in the surrounding area, such as a light source that is emitting infrared rays.
Remedy
Move the projector or turn off the interfering device, such as a light source that is emitting infrared rays.
Problem Solving
132
Other Problems
No sound can be heard or the sound is faint
Check
Check that the audio/video cable is securely attached to both the projector and audio source.
Is the projector volume set to the minimum?
Is the audio cable's specification "No resistance"?
Is it connected with an HDMI cable?
Is Output audio from the projector selected?
(Only when projecting USB Display)
Is the correct audio input selected?
Check the Audio Input from the configuration menu.
s Extended - Operation - Audio Input
Remedy
Disconnect the cable from the audio input port, and then reconnect the cable.
Is the volume for the computer or from the image source set to the minimum?
Is the Mic Input Level set at the maximum?
Adjust the volume so that sound can be heard.
s
s
Adjust the volume so that sound can be heard.
Is A/V Mute active?
Lower the Mic Input Level.
s Settings - Mic Input Level
Press the [A/V Mute] button on the remote control to cancel A/V Mute.
s
"Hiding the Image and Sound Temporarily (A/V Mute)" p.67
When using a commercially available audio cable, make sure it is labeled "No resistance".
If no audio is output when connecting via an HDMI cable, set the connected equipment to PCM output.
Click All Programs - EPSON Projector - Epson USB Display - Epson USB Display Vx.xx Settings, and then select
Output audio from the projector .
No sound can be heard from the microphone
Check
Is the microphone connected correctly?
Is the microphone input volume turned down too low?
Remedy
Disconnect the cable from the Microphone (Mic) port, and then reconnect the cable.
s
"Connecting External Equipment" p.34
Adjust the microphone input volume so that sound can be heard.
s Settings - Mic Input Level
Problem Solving
133
Check
Are you using a plug-in power type microphone?
Remedy
The projector does not support plug-in power type microphones. Use a commercially available dynamic microphone.
s Settings - Mic Input Level
The remote control does not work
Check
Is the remote control light-emitting area pointing towards the remote receiver on the projector during operation?
Is the remote control too far from the projector?
Is direct sunlight or strong light from fluorescent lamps shining onto the remote receiver?
Is the correct setting for the Remote Receiver selected?
Are the batteries dead or have the batteries been inserted in the wrong direction?
Remedy
Point the remote control towards the remote receiver during operation.
s
"Remote control operating range" p.19
The operating range for the remote control is about 6 m.
s
"Remote control operating range" p.19
Set the projector up in a location where strong light does not shine onto the remote receiver. Or set the remote receiver to
Off from Remote Receiver in the Configuration menu.
s Settings - Remote Receiver
Check the Remote Receiver from the Configuration menu.
s Settings - Remote Receiver
Insert new batteries in the correct direction.
s
"Replacing the remote control batteries" p.18
I want to change the language for messages and menus
Check
Change the language setting.
Remedy
Adjust the Language setting from the Configuration menu.
s Extended - Language
Problem Solving
134
Mail is not received even if an error occurs with the projector
Check
Is Standby Mode set to Communication On?
Did a fatal abnormality occur and the projector come to a sudden stop?
Is power being supplied to the projector?
Is the Mail Notification function set correctly in the Configuration menu?
Remedy
To use the Mail Notification function when the projector is in standby, set Communication On in Standby Mode from the Configuration menu.
s
Extended - Standby Setup - Standby Mode p.103
When the projector comes to a sudden stop, email cannot be sent.
If the abnormal state continues, contact your local dealer or the nearest address provided in the Epson Projector Contact
List.
s Epson Projector Contact List
Check that your electrical outlet or power source is functioning correctly.
An error notification email is sent according to the Mail settings in the Configuration menu. Check if it is set correctly.
s
Image file names are not displayed correctly in Slideshow
Is the file name too long?
Check
Are there any 2-byte characters in the file name?
Remedy
The file name can be up to 8 characters long. For file names longer than this, the middle of the name is omitted to shorten the name to 8 characters.
Only alphanumerical characters and symbols can be used in file names. Any other characters are replaced with a question mark (?).
Cannot change settings using a web browser
Check
Are the user ID and password correct?
Remedy
Enter "EPSONWEB" as the user ID. This cannot be changed. Enter the user ID even if the password setting is disabled.
Enter the password you set in Web Control Password. The default password is "admin".
About Event ID
135
Check the numbers and then apply the following countermeasures. If you cannot resolve the problem, contact your network administrator, or contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Event ID
0432
0435
0434
0482
0484
0485
0433
0481
0483
04FE
0479
04FF
0891
0892
0893
0894
0898
Cause
Failed to startup EasyMP Network Projection.
Network communication is unstable.
Cannot play transferred images.
Communication was disconnected from the computer.
EasyMP Network Projection ended unexpectedly.
A system error occurred in the projector.
Cannot find an access point with the same SSID.
The WPA/WPA2 authentication type does not match.
The WEP/TKIP/AES encryption type does not match.
Communication was disconnected because the projector connected to an unauthorized access point.
Failed to acquire DHCP.
Restart the projector.
Remedy
Check the network communication status, and reconnect after waiting for a while.
Restart EasyMP Network Projection.
Check the network communication status, and then restart the projector.
Restart the projector.
Set the computer, the access point, and the projector to the same SSID.
Check that the wireless LAN security settings are correct.
s
Contact your network administrator for more information.
0899 Other communication errors
Check that the DHCP server is operating correctly. If you are not using DHCP, turn off the DHCP setting.
s Wireless LAN - IP Settings
If restarting the projector or EasyMP Network Projection does not solve the problem, contact your local dealer or the nearest address provided in the Epson
Projector Contact List.
s Epson Projector Contact List
Maintenance
This chapter provides information on maintenance procedures to ensure the best level of performance from the projector for a long time to come.
Cleaning
137
You should clean the projector if it becomes dirty or if the quality of projected images starts to deteriorate.
Attention
Turn off the projector's power before cleaning.
Attention
Do not rub the lens with harsh materials or subject the lens to shocks, as it can easily become damaged.
Cleaning the Projector's Surface
Clean the projector's surface by wiping it gently with a soft cloth.
If the projector is particularly dirty, moisten the cloth with water containing a small amount of neutral detergent, and then firmly wring the cloth dry before using it to wipe the projector's surface.
Attention
Do not use volatile substances such as wax, alcohol, or thinner to clean the projector's surface. The quality of the case may change or become discolored.
Cleaning the Obstacle Sensor
Clean the obstacle sensor when the message "Remove any obstacles that are interfering with the projection area." is displayed along with a warning sound. Use a commercially available cloth for cleaning glasses to gently wipe the obstacle sensor.
Cleaning the Projection Window
Use a commercially available cloth for cleaning glasses to gently wipe the projection window.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the lens. The projector may catch fire because of the high temperature of the lamp inside the projector.
Warning
Do not use sprays that contain flammable gas to remove dirt and dust from the obstacle sensor. The projector may catch fire because of the high temperature of the lamp inside the projector.
Cleaning
Attention
Do not rub the obstacle sensor with harsh materials or subject the sensor to shocks.
Damage on the surface of the sensor may cause malfunctions.
Cleaning the Air Filter
Clean the air filter and the air intake vent when the following message is displayed.
"The projector is overheating. Make sure nothing is blocking the air vent, and clean or replace the air filter."
Attention
• Dust collecting on the air filter may cause the internal temperature of the projector to rise, leading to a malfunction or early deterioration of optical parts. Clean the air filter immediately when the message is displayed.
• Do not rinse the air filter in water. Do not use detergents or solvents.
138 a • If a message is frequently displayed, even after cleaning, it is time to replace the air filter. Replace it with a new air filter.
s
"Replacing the Air Filter" p.142
• It is recommended that you clean these parts at least once every three months. Clean them more often than this if using the projector in a particularly dusty environment.
Replacing Consumables
This section explains how to replace the lamp and the air filter.
Replacing the Lamp
Lamp replacement period
It is time to replace the lamp when:
• The following message is displayed.
"It is time to replace your lamp. Please contact your Epson projector reseller or visit www.epson.com to purchase."
• The lamp indicator flashes orange.
The message is displayed for 30 seconds.
139
• The projected image gets darker or starts to deteriorate.
Attention
• The lamp replacement message is set to appear after the following time periods in order to maintain the initial brightness and quality of the projected images.
When Power Consumption is set to Normal: Approx. 2900 hours
When Power Consumption is set to ECO: Approx. 3900 hours s Settings - Power Consumption
• If you continue to use the lamp after the replacement period has passed, the possibility that the lamp may blow increases. When the lamp replacement message is displayed, replace the lamp with a new one as soon as possible, even if it is still working.
• Do not repeatedly turn off the power and immediately back on. Turning the power on and off frequently may shorten the lamp's operating life.
• Depending on the individual characteristics of the lamp and the way it has been used, the lamp may become darker or stop working before the message is displayed. You should always have a spare lamp unit ready in case it is needed.
Replacing Consumables
How to replace the lamp
The lamp can be replaced even when the projector is suspended from a wall or ceiling.
Warning
• When replacing the lamp because it has stopped working, there is a possibility that the lamp may be cracked. When replacing the lamp of a projector that has been installed on a wall or ceiling, assume that the lamp is cracked and stand to the side of the lamp cover, not underneath it. Also, remove the lamp cover gently.
• Never disassemble or modify a lamp. If a modified or disassembled lamp is installed in the projector and used, it could cause a fire, electric shock, or an accident.
Caution
Wait until the lamp has cooled down sufficiently before removing the lamp cover. If the lamp is still hot, burns or other injuries may result. It takes approximately one hour after the power has been turned off for the lamp to sufficiently cool down.
a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cord.
b Wait until the lamp has sufficiently cooled down, and then remove the lamp cover at the top of the projector.
Loosen the lamp cover fixing screw with the screwdriver supplied with the new lamp unit or a cross-head screwdriver. Then slide the lamp cover straight forward and lift to remove it.
c Loosen the two lamp fixing screws.
140
Replacing Consumables d Remove the old lamp by pulling the handle.
If the lamp is cracked, replace it with a new lamp, or contact your local dealer for further advice.
s Epson Projector Contact List
①
②
141 e Install the new lamp.
Insert the new lamp along the guide rail in the correct direction so that it fits in place, push in firmly, and then press the handle down.
Tighten the two lamp fixing screws.
②
① f Attach the lamp cover.
Replacing Consumables
142 a
Only reset the lamp hours after the lamp has been replaced. Otherwise, the lamp replacement period will not be indicated correctly.
Attention
• Make sure you install the lamp securely. If the lamp cover is removed, the power turns off automatically as a safety precaution. If the lamp or the lamp cover is not installed correctly, the power does not turn on.
• This product includes a lamp component that contains mercury (Hg). Please consult your local regulations regarding disposal or recycling. Do not dispose of it with normal waste.
Replacing the Air Filter
Air filter replacement period
If the message is displayed frequently even though the air filter has been cleaned, replace the air filter.
How to replace the air filter
The air filter can be replaced even when the projector is suspended from a wall or ceiling.
a After you turn off the projector's power and the confirmation buzzer beeps twice, disconnect the power cord.
b Open the air filter cover.
Press the tabs on the air filter cover and open the cover.
Resetting the lamp hours
The projector records how long the lamp is on and a message and indicator notify you when it is time to replace the lamp. After replacing the lamp, make sure you reset the lamp hours from the Configuration menu.
s
Replacing Consumables c Remove the air filter.
Grip the tab in the center of the air filter, and pull the air filter straight out.
d Install the new air filter.
143
Replacing Consumables e Close the air filter cover.
a
Dispose of used air filters properly in accordance with your local regulations.
Material of the frame part: Polypropylene
Material of the filter part: Polypropylene
144
Appendix
Optional Accessories and Consumables
146
The following optional accessories and consumables are available. Please purchase these products as and when needed. The following list of optional accessories and consumables is current as of: November 2011. Details of accessories are subject to change without notice.
Optional Accessories
Document Camera ELPDC06/ELPDC11
Use when projecting images such as books, OHP documents, or slides.
Computer cable ELPKC02
(1.8 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC09
(3 m - for mini D-Sub15-pin/mini D-Sub 15pin)
Computer cable ELPKC10
(20 m - for mini D-Sub15-pin/mini D-Sub 15pin)
D port cable ELPKC22
(Mini D-Sub 15-pin/3 m for D port)
Use when connecting to the D port on an image source.
Component video cable ELPKC19
(3 m - for mini D-Sub 15-pin/RCA male
^
3)
Use to connect a Component Video
source.
Wireless LAN unit ELPAP07
Use when connecting the projector to a computer wirelessly and projecting.
Quick Wireless Connection USB Key ELPAP08
Use when you want to quickly establish one-to-one connection between the projector and a computer with Windows installed.
Ceiling mount * ELPMB23
Use when installing the projector on a ceiling.
Easy Interactive Pen ELPPN03A/ELPPN03B
(EB-485Wi/EB-480i/EB-475Wi only)
Pens for the Easy Interactive Function. You cannot use Easy Interactive Pens with the same model number at the same time.
Replacement Pen Tips ELPPS01 (EB-485Wi/EB-480i/EB-475Wi only)
Replacement pen tips for the Easy Interactive Pen.
Interface box ELPCB01
* Special expertise is required to suspend the projector. Contact your local dealer or the nearest address provided in the Epson Projector Contact List.
s Epson Projector Contact List
Consumables
Lamp unit ELPLP71
Use as a replacement for a used lamp.
Air Filter ELPAF40
Use as a replacement for a used air filter.
Screen Size and Projection Distance
Projection Distance (For EB-485Wi/EB-485W/
EB-475Wi/EB-475W)
A Projection distance
B The distance between the projector and the top of the screen (when mounting on a wall or ceiling, or installing vertically)
The distance between the projector and the bottom of the screen (when placing on a surface such as a desk)
147
C The distance between the projector and the bottom of the screen (when mounting on a wall or ceiling, or installing vertically)
The distance between the projector and the top of the screen (when placing on a surface such as a desk)
16:10 Screen Size
60"
70"
80"
90"
100"
129x81
151x94
172x108
194x121
215x135
A
Minimum (Wide) to
Maximum (Tele)
35 - 48
41 - 56
47 - 60
53 - 60
60 *
* Project using Wide (maximum zoom).
B
Minimum
(Wide)
10
13
15
18
21
Unit: cm
C
Minimum
(Wide)
91
107
123
139
156
4:3 Screen Size
53"
60"
70"
80"
88"
108x81
122x91
142x107
163x122
179x134
A
Minimum (Wide) to
Maximum (Tele)
35 - 48
40 - 55
47 - 60
54 - 60
59 - 60
B
Minimum
(Wide)
10
12
15
18
21
Unit: cm
C
Minimum
(Wide)
91
104
122
140
155
Screen Size and Projection Distance
148
16:9 Screen Size
59"
60"
70"
80"
90"
97"
131x74
133x75
155x87
177x100
199x112
215x121
A
Minimum (Wide) to
Maximum (Tele)
35 - 48
36 - 49
42 - 58
49 - 60
55 - 60
60 *
* Project using Wide (maximum zoom).
B
Minimum
(Wide)
14
14
18
22
25
28
Unit: cm
C
Minimum
(Wide)
88
89
105
121
137
149
Projection Distance (For EB-480i/EB-480/EB-470)
A Projection distance
B The distance between the projector and the top of the screen (when mounting on a wall or ceiling, or installing vertically)
The distance between the projector and the bottom of the screen (when placing on a surface such as a desk)
C The distance between the projector and the bottom of the screen (when mounting on a wall or ceiling, or installing vertically)
The distance between the projector and the top of the screen (when placing on a surface such as a desk)
A
4:3 Screen Size
56"
60"
70"
80"
90"
93"
114x85
122x91
142x107
163x122
183x137
189x142
Minimum (Wide) to
Maximum (Tele)
35 - 48
38 - 52
44 - 60
51 - 60
58 - 60
60 *
* Project using Wide (maximum zoom).
B
Minimum
(Wide)
8
9
11
14
16
17
Unit: cm
C
Minimum
(Wide)
93
100
118
136
154
159
Screen Size and Projection Distance
16:9 Screen Size
52"
60"
70"
80"
85"
115x65
133x75
155x87
177x100
188x106
A
Minimum (Wide) to
Maximum (Tele)
35 - 49
41 - 56
48 - 60
56 - 60
59 - 60
B
Minimum
(Wide)
19
23
27
32
35
Unit: cm
C
Minimum
(Wide)
83
97
115
132
141
149
Supported Monitor Displays
Supported Resolutions
Computer signals (analog RGB)
Signal
VGA
SVGA
XGA
WXGA
WXGA+
WXGA++
SXGA
SXGA+
WSXGA+ *
MAC13”
MAC16”
MAC19”
1, 2
Refresh Rate (Hz)
60/72/75/85
56/60/72/75/85
60/70/75/85
60
60
60/75/85
60/75/85
60
70/75/85
60/75/85
60/75/85
60/75
60
67
75
75
59
75
Resolution (dots)
640x480
800x600
1024x768
1280x768
1366x768
1280x800
1440x900
1600x900
1152x864
1280x1024
1280x960
1400x1050
1680x1050
640x480
832x624
1024x768
1024x768
1152x870 MAC21”
* 1 EB-485Wi/EB-485W/EB-475Wi/EB-475W only
* 2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
Images may also be projected when signals other than the above are input.
However, some functions may be limited.
Component Video
Signal
SDTV (480i)
SDTV (576i)
SDTV (480p)
SDTV (576p)
HDTV (720p)
HDTV (1080i)
Composite video
Signal
TV (NTSC)
TV (SECAM)
TV (PAL)
Refresh Rate (Hz)
60
50
60
50
50/60
50/60
Refresh Rate (Hz)
60
50
50/60
Input signal from the HDMI port
Signal
VGA
SVGA
XGA
WXGA
WXGA+
WXGA++
WSXGA+ * 1, 2
Refresh Rate (Hz)
60
60
60
60
60
60
60
60
Resolution (dots)
720x480
720x576
720x480
720x576
1280x720
1920x1080
Resolution (dots)
720x480
720x576
720x576
Resolution (dots)
640x480
800x600
1024x768
1280x800
1366x768
1440x900
1600x900
1680x1050
150
Supported Monitor Displays
Signal
SXGA
SXGA+
SDTV (480i/480p)
SDTV (576i/576p)
HDTV (720p)
HDTV (1080i)
HDTV (1080p)
Refresh Rate (Hz)
60
60
60
60
50
50/60
50/60
24/30/50/60
Resolution (dots)
1280x960
1280x1024
1400x1050
720x480
720x576
1280x720
1920x1080
1920x1080
* 1 EB-485Wi/EB-485W/EB-475Wi/EB-475W only
* 2 Only compatible when Wide is selected as the Resolution from the
Configuration menu.
151
Specifications
Projector General Specifications
Product name
Dimensions
LCD panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp
Max. audio output
Speaker
Power supply
Power con‐ sumption
100 to 120 V area
220 to 240 V area
Operating altitude
Operating temperature
Storage temperature
Mass
EB-485Wi EB-485W EB-480i
367 (W) x 143 (H) x 375 (D) mm (not including raised section)
0.59" Wide 0.55"
EB-480
Polysilicon TFT active matrix
1,024,000
WXGA (1280 (W)x 800 (H) dots)x 3
786,432
XGA (1024 (W) x 768 (H) dots)x 3
Manual
Digital (1-1.35)
UHE lamp, 215 W Model No.: ELPLP71
16 W
1
100-240V AC±10% 50/60Hz 3.1-1.5A
Operating: 313 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 300 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Approx. 5.3 kg
Operating: 313 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 300 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Operating: 313 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 300 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Altitude 0 to 2,286 m
5 to +35°C (No condensation)
-10 to +60°C (No condensation)
Approx. 5.2 kg Approx. 5.3 kg
Operating: 313 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 300 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Approx. 5.2 kg
152
Specifications
Product name
Dimensions
LCD panel size
Display method
Resolution
Focus adjustment
Zoom adjustment
Lamp
Max. audio output
Speaker
Power supply
Power con‐ sumption
100 to 120 V area
Operating altitude
Operating temperature
Storage temperature
Mass
220 to 240 V area
EB-475Wi EB-475W
367 (W) x 143 (H) x 375 (D) mm (not including raised section)
EB-470
0.55" 0.59" Wide
Polysilicon TFT active matrix
1,024,000
WXGA (1280 (W) x 800 (H) dots)x 3
786,432
XGA (1024 (W) x 768 (H) dots)x
3
Manual
Operating: 287 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 275 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Approx. 5.3 kg
Digital (1-1.35)
UHE lamp, 190 W Model No.: ELPLP71
16 W
1
100-240V AC±10% 50/60Hz 2.9-1.3A
Operating: 287 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 275 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
Altitude 0 to 2,286 m
5 to +35°C (No condensation)
-10 to +60°C (No condensation)
Approx. 5.2 kg
Operating: 287 W
Standby power consumption
(Communication On): 7.5 W
Standby power consumption
(Communication Off): 0.21 W
Operating: 275 W
Standby power consumption
(Communication On): 8.3 W
Standby power consumption
(Communication Off): 0.27 W
153
Specifications
Connectors Computer1 port
Computer2 port
Video port
S-Video port
Audio1 port
Audio2 port
Audio-L/R port
Mic port
Audio Out port
Monitor Out port
HDMI port
USB-A port *
USB-B port *
USB port
(for Wireless LAN unit)
LAN port
RS-232C port
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
* Supports USB 2.0. However, the operation of all USB compatible devices is not guaranteed.
Mini D-Sub15-pin (female)
Mini D-Sub15-pin (female)
RCA pin jack
Mini DIN 4-pin
Stereo mini pin jack
Stereo mini pin jack
RCA pin jack x 2 (L-R)
Stereo mini pin jack
Stereo mini pin jack
Mini D-Sub15-pin (female)
HDMI (Audio is only supported by PCM)
USB connector (Type A)
USB connector (Type B)
USB connector (Type A)
RJ-45
Mini D-Sub 9-pin (male)
154
Specifications
This product is also designed for IT power distribution system with phase-to-phase voltage 230V.
Angle of tilt
If you use the projector tilted at an angle of more than 5˚ it could be damaged and cause an accident.
155
Specifications
156
DECLARATION of CONFORMITY
According to 47CFR, Part 2 and 15
Class B Personal Computers and Peripherals; and/or
CPU Boards and Power Supplies used with Class B Personal Computers
We:
Located at:
Tel:
Epson America, Inc.
3840 Kilroy Airport Way
MS: 3-13
Long Beach, CA 90806
562-290-5254
Declare under sole responsibility that the product identified herein, complies with 47CFR Part 2 and 15 of the FCC rules as a Class B digital device. Each product marketed, is identical to the representative unit tested and found to be compliant with the standards. Records maintained continue to reflect the equipment being produced can be expected to be within the variation accepted, due to quantity production and testing on a statistical basis as required by 47CFR 2.909. Operation is subject to the following two conditions : (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Trade Name: EPSON
Type of Product:
Model:
Projector
H452C/H453C/H454C/H455C/H456C/H485C/
H486C
FCC Compliance Statement
For United States Users
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause interference to radio and television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures.
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface connector, do not leave cables connected to unused interfaces. Changes or modifications not expressly approved by the manufacturer could void the user's authority to operate the equipment.
Appearance
157
Units: mm
Appearance
Without feet
With feet
Units: mm
158
Glossary
159
This section briefly explains the difficult terms that are not explained in the text of this guide. For details, refer to other commercially available publications.
AMX Device Discovery
Aspect Ratio
Component Video
Composite video
Contrast
DHCP
Gateway Address
HDCP
HDTV
Interlace
IP Address
Progressive
Refresh Rate
SDTV
AMX Device Discovery is a technology developed by AMX to facilitate AMX control systems for easy operation of the target equipment.
Epson have implemented this protocol technology, and have provided a setting to enable the protocol function (ON).
See the AMX Web site for more details.
URL http://www.amx.com/
The ratio between an image's length and its height. Screens with a horizontal:vertical ratio of 16:9, such as HDTV screens, are known as wide screens.
SDTV and general computer displays have an aspect ratio of 4:3.
A method that separates the video signal into a luminance component (Y), and a blue minus luminance (Cb or Pb) and a red minus luminance (Cr or
Pr).
A method that combines the video signal into a luminance component and a color component for transmission down a single cable.
The relative brightness of the light and dark areas of an image can be increased or decreased to make text and graphics stand out more clearly, or to make them appear softer. Adjusting this particular property of an image is called "contrast adjustment".
to equipment connected to a network.
This is a server (router) for communicating across a network (subnet) divided according to subnet mask
HDCP is an abbreviation for High-bandwidth Digital Content Protection. It is used to prevent illegal copying and protect copyrights by encrypting digital signals sent over DVI and HDMI ports. Because the HDMI port on this projector supports HDCP, it can project digital images protected by
HDCP technology. However, the projector may not be able to project images protected with updated or revised versions of HDCP encryption.
An abbreviation for High-Definition Television that refers to high-definition systems which satisfy the following conditions.
• Vertical resolution of 720p or 1080i or greater (p = Progressive
of 16:9
Transmits information needed to create one screen by sending every other line, starting from the top of the image and working down to the bottom.
Images are more likely to flicker because one frame is displayed every other line.
A number to identify a computer connected to a network.
Projects information to create one screen at a time, displaying the image for one frame. Even though the number of scan lines is the same, the amount of flicker in images decreases because the volume of information has doubled compared with an interlace system.
The light-emitting element of a display maintains the same luminosity and color for an extremely short time. Because of this, the image must be scanned many times per second to refresh the light-emitting element. The number of refresh operations per second is called the Refresh rate and is expressed in hertz (Hz).
An abbreviation for Standard Definition Television that refers to standard television systems which do not satisfy the conditions for HDTV
Definition Television.
Glossary
SNMP sRGB
SSID
Subnet Mask
SVGA
S-Video
SXGA
Sync.
Tracking
Trap IP Address
VGA
XGA
160
An abbreviation for Simple Network Management Protocol, which is the protocol for monitoring and controlling devices such as routers and computers connected to a TCP/IP network.
An international standard for color intervals that was formulated so that colors that are reproduced by video equipment can be handled easily by computer operating systems (OS) and the Internet. If the connected source has an sRGB mode, set both the projector and the connected signal source to sRGB.
SSID is identification data for connecting to another device on a wireless LAN. Wireless communication is possible between devices with the same
SSID.
This is a numerical value that defines the number of bits used for the network address on a divided network (subnet) from the IP address.
A screen size standard with a resolution of 800 (horizontal) x 600 (vertical) dots.
A method that separates the video signal into a luminance component (Y) and a color component (C).
A screen size standard with a resolution of 1,280 (horizontal) x 1,024 (vertical) dots.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the phases of these signals (the relative position of the crests and the troughs in the signal) is called
Synchronization. If the signals are not synchronized, flickering, blurriness, and horizontal interference occur.
The signals output from computers have a specific frequency. If the projector frequency does not match this frequency, the resulting images are not of a good quality. The process of matching the frequency of these signals (the number of crests in the signal) is called Tracking. If tracking is not carried out correctly, wide vertical stripes appear in the signal.
for the destination computer used for error notification in SNMP.
A screen size standard with a resolution of 640 (horizontal) x 480 (vertical) dots.
A screen size standard with a resolution of 1,024 (horizontal) x 768 (vertical) dots.
General Notes
161
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Seiko
Epson Corporation. No patent liability is assumed with respect to the use of the information contained herein. Neither is any liability assumed for damages resulting from the use of the information contained herein.
Neither Seiko Epson Corporation nor its affiliates shall be liable to the purchaser of this product or third parties for damages, losses, costs, or expenses incurred by the purchaser or third parties as a result of: accident, misuse, or abuse of this product or unauthorized modifications, repairs, or alterations to this product, or (excluding the
U.S.) failure to strictly comply with Seiko Epson Corporation's operating and maintenance instructions.
Seiko Epson Corporation shall not be liable against any damages or problems arising from the use of any options or any consumable products other than those designated as
Original Epson Products or Epson Approved Products by Seiko Epson Corporation.
The contents of this guide may be changed or updated without further notice.
Illustrations in this guide and the actual projector may differ.
Restriction of Use
When this product is used for applications requiring high reliability/safety such as transportation devices related to aviation, rail, marine, automotive etc.; disaster prevention devices; various safety devices etc; or functional/precision devices etc, you should use this product only after giving consideration to including fail-safes and redundancies into your design to maintain safety and total system reliability. Because this product was not intended for use in applications requiring extremely high reliability/safety such as aerospace equipment, main communication equipment, nuclear power control equipment, or medical equipment related to direct medical care etc, please make your own judgment on this product’s suitability after a full evaluation.
Wireless Telegraphy Act Regulations
The following acts are prohibited by the Wireless Telegraphy Act.
• Modifying and disassembling (including the antenna)
• Removing the label of conformance
About Notations
Microsoft
Microsoft
® Windows ® 98 operating system
® Windows ® Me operating system
Microsoft
Microsoft
® Windows ® 2000 operating system
® Windows ® XP operating system
Microsoft
Microsoft
®
®
Windows Vista
Windows ®
® operating system
7 operating system
In this guide, the operating systems above are referred to as "Windows 98",
"Windows Me", "Windows 2000", "Windows XP", "Windows Vista", and
"Windows 7". Furthermore, the collective term Windows may be used to refer to Windows 98, Windows Me, Windows 2000, Windows XP,
Windows Vista, and Windows 7, and multiple versions of Windows may be referred to as, for example, Windows 98/Me/2000/XP/Vista/7, with the
Windows notation omitted.
Mac OS X 10.3.x
Mac OS X 10.4.x
Mac OS X 10.5.x
Mac OS X 10.6.x
Mac OS X 10.7.x
In this guide, the operating systems above are referred to as "Mac OS X
10.3.x", "Mac OS X 10.4.x", "Mac OS X 10.5.x", "Mac OS X 10.6.x", and
"Mac OS X 10.7.x". Furthermore, the collective term "Mac OS X" is used to refer to them all.
General Notes
General Notice:
IBM, DOS/V, and XGA are trademarks or registered trademarks of International
Business Machines Corp.
Macintosh, Mac, Mac OS, and iMac are trademarks of Apple Inc.
Microsoft, Windows, Windows NT, Windows Vista, PowerPoint, and Windows logo are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.
eneloop ® is a registered trademark of Sanyo Electronic Co., Ltd.
WPA ™ and WPA2 ™ are registered trademarks of Wi-Fi Alliance.
HDMI and High-Definition Multimedia Interface are the trademarks or registered trademarks of HDMI Licensing LLC.
PJLink trademark is a trademark applied for registration or is already registered in
Japan, the United States of America and other countries and areas.
Crestron and Crestron RoomView are registered trademarks of Crestron Electronics,
Inc.
Other product names used herein are also for identification purposes only and may be trademarks of their respective owners. Epson disclaims any and all rights in those marks.
©SEIKO EPSON CORPORATION 2011. All rights reserved.
162
Index
163
A
A/V Mute ...................................................... 67
Abs. Color Temp. ........................................ 99
Air exhaust vent ........................................... 10
Air filter replacement period ................... 142
Aspect .................................................... 52, 100
Audio Input ................................................ 103
Auto Iris .................................................. 52, 99
Auto Setup .................................................... 99
B
Basic menu ................................................. 107
Blackboard .................................................... 51
Brightness ..................................................... 98
C
Ceiling ................................................... 24, 103
Cleaning ...................................................... 137
Cleaning the air filter and air intake vent
........................................................................ 138
Cleaning the projector's surface .............. 137
Color Adjustment ........................................ 99
Color Mode ............................................ 51, 98
Color Saturation .......................................... 98
Computer port ............................................. 12
Configuration menu .................................... 95
Connection mode ...................................... 108
Consumables .............................................. 146
Continuous ................................................... 79
Contrast ........................................................ 98
Control panel ............................................... 15
Control Panel Lock ............................. 82, 101
Crestron RoomView ................................... 90
Cross .............................................................. 69
D
Direct Power On ........................................ 103
Display ........................................................ 103
Display Background .................................. 103
Display Order ............................................... 79
Display settings ............................................ 78
Distance ...................................................... 147
Document Camera .................................... 146
Dynamic ........................................................ 51
E
Easy Interactive Function ................ 104, 105
Easy Interactive Pen .................................... 20
EasyMP Monitor .......................................... 84
Email address ............................................. 112
ESC/VP21 ..................................................... 88
Extended menu .......................................... 103
E-Zoom ......................................................... 69
F
Freeze ............................................................. 67
Front ...................................................... 24, 103
Full Lock ....................................................... 82
G
Gateway Address ............................... 109, 111
H
H/V-Keystone .............................................. 45
HDMI port ................................................... 12
HDMI Video Range .................................. 100
Help function ............................................. 117
High Altitude Mode .................................. 103
How to replace the air filter ..................... 142
How to replace the lamp ........................... 140
I
Image menu .................................................. 98
Image Shift ........................................... 48, 101
Indicators ........................................... 118, 119
Info menu ................................................... 114
Input Signal ........................................ 100, 114
IP Address .................................................. 112
K
Keystone ...................................................... 101
L
Lamp cover ................................................... 10
Lamp Hours ............................................... 114
Lamp indicator ........................................... 118
Lamp replacement period ........................ 139
Language ..................................................... 105
M
Mail Notification ................................. 87, 112
Mail Notification menu ............................ 111
Message Broadcasting ................................. 84
Messages ..................................................... 103
Mic Input Level .......................................... 101
Monitor displays ........................................ 150
Index
164
Mouse pointer .............................................. 70
N
Network Configuration ............................ 106
Network information ................................ 106
Network menu ........................................... 105
Noise Reduction ........................................ 100
O
Operating temperature ..................... 152, 153
Operation .................................................... 103
Optional accessories .................................. 146
Overheating ................................................ 119
P
Part names and functions ........................... 10
Password protect .......................................... 80
Password protect sticker ............................. 81
Pattern ......................................................... 102
Photo ............................................................. 51
PJLink ............................................................ 89
PJLink Password ........................................ 107
Pointer ........................................................... 68
Pointer Shape ............................................. 101
Port Number .............................................. 112
Position ....................................................... 100
Power Consumption ................................. 101
Power indicator .......................................... 118
Power inlet .................................................... 12
Power On Protect ........................................ 80
Presentation ........................................... 51, 74
Problem solving ......................................... 118
Progressive .................................................. 100
Q
Quick Corner ............................................. 101
R
Projection ................................................... 103
Projection window ...................................... 11
Projector Keyword .................................... 108
Projector Name .......................................... 107
Projector setup ............................................. 84
Reading mail ................................................. 87
Rear ....................................................... 24, 103
Rear screen .................................................... 24
Refresh Rate ................................................ 114
Remote control ............................................ 16
Remote receiver ..................................... 10, 11
Replacing batteries ....................................... 18
Reset All ...................................................... 115
Reset Lamp Hours ..................................... 115
Reset menu ......................................... 114, 115
Resetting the lamp operating time .......... 142
Resolution ................................................... 114
Rotating images ........................................... 76
S
Screen size ................................................... 147
Screen switching time ................................. 79
Security menu ............................................ 109
Select Drive ................................................... 76
Settings menu ............................................. 101
Sharpness ...................................................... 98
Signal menu .................................................. 99
Sleep Mode ................................................. 103
Slideshow ................................................ 75, 78
SMTP Server ............................................... 112
SNMP ............................................................ 87
Soft keyboard ............................................. 106
Source .......................................................... 114
Source Search ......................................... 15, 40
Specifications ............................................. 152
SSID ............................................................. 108
Standby audio ............................................. 104
Standby microphone ................................. 104
Standby mode ............................................ 104
Standby setup ............................................. 104
Startup Screen ............................................ 103
Storage temperature .......................... 152, 153
Subnet Mask ....................................... 109, 111
Supported monitor displays ..................... 150
S-Video port ................................................. 13
Sync Info ..................................................... 114
Sync. ............................................................ 100
T
Temp indicator .......................................... 118
Theatre .......................................................... 51
Tint ................................................................ 98
Tracking ...................................................... 100
U
USB Display/Easy Interactive Function
........................................................................ 104
USB Type B ................................................ 104
USB-A port ................................................... 12
Index
USB-B port ................................................... 12
User Button ................................................ 102
User Pattern .................................................. 73
User's Logo ................................................... 71
User's Logo Protect ...................................... 80
V
W
Web browser ................................................ 84
Web Control ................................................. 85
Web Control Password ............................. 107
Web Remote ................................................. 85
Whiteboard ................................................... 51
Wired LAN menu ...................................... 111
Wireless LAN menu .................................. 108
Wireless LAN Power ................................. 108
Wireless LAN system ................................ 108
Wireless mouse function ............................ 70
Wireless Mouse/USB Display .................. 104
Z
Video port ..................................................... 13
Video Signal ....................................... 100, 114
Volume ........................................................ 101
Zoom ........................................................... 101
165
advertisement
Key Features
- Standard throw projector Grey, White
- LCD 2600 ANSI lumens
- Lamp 3000 h
- WXGA (1280x800) 3000:1
- Screen size compatibility: 1524 - 2540 mm (60 - 100")
- Focus: Manual Zoom capability
- Built-in speaker(s) 16 W
- AC 275 W