マニュアル 英語(PDF:423.91KB)

マニュアル 英語(PDF:423.91KB)
Installation Precautions
Mitsubishi General-Purpose Programmable Controller
Renewal Tool Conversion Adapter
general specifications defined in the MELSEC-Q series CPU module user’s manual. Failure to
Do not come in direct contact with the conductive area of the conversion adapter. Doing so could
lead to system malfunction or failure.
Fully secure the conversion adapter and conversion adapter anchor base using the installation
ERNT-AQTY51
screws, and tighten the installation screws securely within the specified torque range. Failure to
do so could cause the conversion adapter and anchor base to fall, resulting in conversion
adapter and conversion adapter anchor base damage.
User’s Manual
(使用前请务必阅读)
Use the conversion adapter and conversion adapter anchor base in an environment of the
do so could lead to electric shock, fire, malfunction or product failure or deterioration.
Model
● 安全注意事项 ●
CAUTION
When installing the conversion adapter, be careful of conversion adapter corners, installation
使用本产品时,请仔细阅读本手册,并充分注意安全,正确地
使用产品。
本手册中标注的注意事项仅记载了与本产品相关的内容。关于
可编程控制器系统的安全注意事项,请参阅所使用的MELSEC-Q
系列CPU模块的用户手册。
在本●安全注意事项●中,安全注意事项的等级分为「警告」
和「注意」。
screws, etc. Failure to do so may result in injury.
Always check for correct match between MELSEC-Q Series and the conversion adapter.
Incorrect match can cause damage to the MELSEC-Q Series module.
警告
表示错误操作可能造成危险后果,引起死亡
或重伤事故。
注意
表示错误操作可能造成危险后果,引起中度
伤害、轻伤及财产损失。
Wiring Precautions
WARNING
Be sure to shut off all phases of the external power supply before performing installation or wiring
work. Failure to do so could result in electric shock or product damage.
If you want to energize and run the unit after completing the installation and wiring work, be sure
to close the terminal block cover attached to the MELSEC-A series terminal block. Failure to do
so could result in electric shock.
CAUTION
ERNT-AQTY51
Properly wire the conversion adapter after verifying the rated voltage and terminal layout of the
另外,根据情况不同,即使是 注意中记载的事项,也可能
引发严重后果。不管哪个记载的都是非常重要的内容,请务必
遵守。
请妥善保管本手册,以便需要时取阅,并请将本手册交给最终
用户。
input/output module to be used. Connecting a power supply with a different rating or improper
wiring could lead to fire or product failure.
Securely tighten the conversion adapter installation screws, conversion adapter anchor base
【安装注意事项】
注 意
installation screws and MELSEC-A series terminal block installation screws within the specified
torque range. A loose screw may result in a short circuit, fire or malfunction. An excessively
Model
ERNT-AQTY51
50CM-D180063-C(1602)
tightened screw may result in screw or conversion adapter damage, causing the conversion
adapter to fall, a short circuit or product malfunction.
Do not allow foreign matter such as cuttings or wiring shavings to enter the conversion adapter or
module. Doing so could lead to fire, failure or malfunction.
● 应在MELSEC-Q系列CPU模块用户手册中记载的一般规格环
境下使用转换适配器及转换适配器固定台。如果在一般规
格范围以外的环境中使用,可能导致触电、火灾、误动作、
产品的损坏或劣化。
HEAD OFFICE: Hulic KUDAN BLDG.1-13-5,KUDANKITA CHIYODA-KU,TOKYO 102-0073,JAPAN
NAGOYA ENGINEERING OFFICE:139 SHIMOYASHIKICHO-SHIMOYASHIKI,KASUGAI,AICHI 486-0906,JAPAN
SAFETY PRECAUTIONS
Startup and Maintenance Precautions
WARNING
(Always read these precautions prior to use.)
Do not touch the terminals during energization. Doing so could result in electric shock or
Before using this product, please read this manual carefully and pay full attention to safety to ensure that
malfunction.
Be sure to shut off all phases of the external power supply before cleaning and retightening the
the product is used correctly.
The precautions presented in this manual are concerned with this product only. For Programmable
Controller system safety precautions, refer to the user’s manual of the MELSEC-Q series CPU module
terminal screws. Failure to do so could lead to electric shock. Excessively tightened screws could
result in conversion adapter or input/output module damage, causing the conversion adapter to
fall, a short circuit or product malfunction.
to be used.
In this manual, the safety precautions are ranked as “WARNING” and “CAUTION”.
CAUTION
WARNING
CAUTION
Indicates that incorrect handling may cause hazardous
conditions, resulting in death or severe injury.
Indicates that incorrect handling may cause hazardous
conditions, resulting in medium or minor injury and/or property
damage.
Do not disassemble or modify the conversion adapter. Doing so could lead to failure,
malfunction, injury or fire.
The conversion adapter case is made of resin. Do not drop or apply excessive impact to the
case. Doing so could lead to conversion adapter damage.
Be careful when touching conversion adapter corners and installation screws. Failure to do so
may result in injury.
Disposal Precautions
CAUTION
according to the circumstances. Always follow the precautions of both levels because they are important
When disposing of the product, treat it as industrial waste.
to personal safety.
Please keep this manual in an easy-to-access location for future reference, and be sure to provide the
manual to the end user.
【启动和维护注意事项】
警 告
● 在通电状态下请勿触摸端子。可能会导致触电或误动作。
● 在清扫或重新紧固端子螺栓时,必须将外部供应全相断
开断开后再进行。如果未全相断开,可能会导致触电。
如果螺栓拧得过紧,可能会造成转换适配器或输入/输出
模块的破损从而导致掉落、短路或误动作。
注 意
● 请不要拆卸、改造转换适配器。否则可能会导致故障、误
动作、受伤或火灾。
● 转换适配器的外壳由树脂制成,因此请避免掉落或使其受
到剧烈冲击。否则可能会损坏转换适配器。
● 触摸转换适配器的角部及安装螺钉时,请充分注意。否则
可能会导致受伤。
【废弃注意事项】
注 意
● 废弃时请将本产品作为工业废弃物处理。
注 意
● 请不要直接触摸转换适配器的导电部分。否则可能会造成
系统误动作、故障。
● 转换适配器及转换适配器固定台应通过安装螺栓切实地
加以固定,安装螺栓应在规定的扭矩范围内切实地拧紧。
可能因掉落而导致转换适配器及转换适配器固定台破损。
● 在安装转换适配器时,请充分注意不要被转换适配器的
角部、安装螺钉或安装金属部件刮到手等。否则可能会
导致受伤。
● 请务必确认MELSEC-Q系列模块和转换适配器的组合是否
正确。在错误组合下使用时,可能会导致MELSEC-Q系列
模块损坏。
Related Manuals
Manual Title
MELSEC-Q Series
Building Block I/O Module
Manual No.
(Model Code)
SH-080042
(13JL99)
User’s Manual
Remarks
By Mitsubishi Electric Corporation
EMC AND LOW VOLTAGE DIRECTIVES
Compliance to the EMC Directive, which is one of the EU Directives, has been a legal obligation for
the products sold in European countries since 1996 as well as the Low Voltage Directive since
1997.
Manufacturers who recognize their products are compliant to the EMC and Low Voltage Directives
are required to declare that print a "CE mark" on their products.
【接线注意事项】
CAUTION level instructions may lead to a serious consequence
Note that failure to observe the
注 意
● 转换适配器安装螺栓、转换适配器固定台安装螺栓、
MELSEC-A系列端子排安装螺栓应在规定的扭矩范围内切
实地拧紧。如果螺栓拧得过松,会导致短路、火灾或误动
作。如果螺栓拧得过紧,有可能造成螺栓及转换适配器破
损从而导致掉落、短路或误动作。
● 请注意不要让切屑或接线头等异物进入转换适配器及模
块内。会导致火灾、故障、误动作。
警 告
● 必须将外部供应全相断开断开后再进行安装作业等。如果
未全相断开,可能会导致触电或产品损坏。
● 安装、配线作业完成之后进行通电、运行时,必须关闭
MELSEC-A系列端子排的端子排盖板。如果未关闭端子排
盖板,可能会导致触电。
Authorized representative in Europe
Authorized representative in Europe is shown below.
Name: Mitsubishi Electric Europe BV
Address: Mitsubishi-Electric-Platz 1, 40882 Ratingen, Germany
1. Overview
This manual describes the Mitsubishi general-purpose Programmable Controller renewal tool
conversion adapter (ERNT-AQTY51). The conversion adapter is a product that converts the differences
注 意
● 请确认所使用输入/输出模块的额定电压及端子排列后正
确地进行转换适配器的配线。
连接不符合额定值的电源或
误配线,会导致火灾或故障。
in MELSEC-A series and MELSEC-Q series pin assignments.
Once you have opened the packaging, verify that it contains the following products.
Product
Quantity
Conversion adapter
1
Mounting bracket
1
Mounting bracket fixing screw (M3.5 x 6)
4
No. of modules
Conversion Adapter
Weight (g)
QY50
AY51-UL
2
AY51-S1
TB2
TB4
TB6
TB8
TB10
TB12
TB14
TB16
TB18
TB20
TB22
TB24
TB26
TB28
TB30
TB32
TB34
TB36
TB38
TB1
TB3
TB5
TB7
TB9
TB11
TB13
TB15
TB17
TB19
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
TB21
TB23
TB25
TB27
TB29
TB31
TB33
TB35
TB37
Isolation method
250
QY80
AY81EP
A Series
Terminal
Block
AY81EP
QY80
(Source Type)
(Source Type)
(Source Type)
32 points
32 points
16 points
Photocoupler isolation
Photocoupler isolation
Photocoupler isolation
Rated load
AY81
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
AY81
No. of input
points
AY51
ERNT-AQT51
Specifications
12/24V DC
voltage
Maximum load
Terminal No.
Signal Name
TB1
TB2
TB3
TB4
TB5
TB6
TB7
TB8
TB9
TB10
TB11
TB12
TB13
TB14
TB15
TB16
TB17
TB18
TB19
TB20
TB21
TB22
TB23
TB24
TB25
TB26
TB27
TB28
TB29
TB30
TB31
TB32
TB33
TB34
TB35
TB36
TB37
TB38
Y00
Y01
Y02
Y03
Y04
Y05
Y06
Y07
Y08
Y09
Y0A
Y0B
Y0C
Y0D
Y0E
Y0F
current
Terminal No. Signal Name
TB1
TB2
TB3
TB4
TB5
TB6
TB7
TB8
TB9
TB10
TB11
TB12
TB13
TB14
TB15
TB16
TB17
TB18
12/24VDC
0V
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
Y00
Y01
Y02
Y03
Y04
Y05
Y06
Y07
Y08
Y09
Y0A
Y0B
Y0C
Y0D
Y0E
Y0F
Q Series
Terminal
Block
Slot No.
TB2
TB4
TB6
TB8
TB10
TB12
TB14
TB16
TB18
TB1
TB3
TB5
TB7
TB9
TB11
TB13
TB15
TB17
12/24VDC
0.8A/point,
OFF leakage
current
Maximum voltage
drop at ON
ON to
OFF
1mA or less
0.1mA or less
1.5V DC (MAX) 0.5A
0.2V DC (TYP) 0.5A,
0.3V DC (MAX) 0.5A
2ms or less
0.5ms or less
1ms or less
2ms or less
(resistance load)
1.5ms or less
(Rated load,
12/24VDC
0V
Open
Open
Y10
Y11
Y12
Y13
Y14
Y15
Y16
Y17
Y18
Y19
Y1A
Y1B
Y1C
Y1D
Y1E
Y1F
Varistor (52-62V)
Diode for absorbing noise
Q Series
Terminal
Block
Slot No.+1
TB2
TB4
TB6
TB8
TB10
TB12
TB14
TB16
TB18
TB1
TB3
consumption
TB5
Wiring method for
TB7
common
TB9
TB11
External
TB13
connection
TB15
TB17
230mA
(TYP. All points ON)
Mounting bracket fixing screw (M3.5 screw)
68 to 92 N・cm
malfunction, injury or fire.
Conversion adapter bottom installation screw (M3 screw)
43 to 57 N・cm
Do not come in direct contact with the conductive area of the conversion adapter. Doing so
Conversion adapter installation screw (M3 screw)
could result in system malfunction or failure.
MELSEC-A series terminal block installation screw (M4 screw)
102 to 138 N・cm
Fully secure the conversion adapter and conversion adapter anchor base using the
installation screws, and securely tighten the screws within the specified torque range.
Failure to do so could cause the conversion adapter and anchor base to fall, resulting in
6. External Dimensions
16-points, 1 common
16-points, 1 common
38-point terminal block
38-point terminal block
18-point terminal block
Unit:mm
4.2 Use Precautions
Item
Depth
Use Precautions
The depth increases. Verification prior to installation is required.
Q series module
+
A series module
Renewal tool
Mounting bracket
Conversion
adapter
53.5
Base ada pter
Conversion adapter
anchor base
(TYP. All points ON)
16-points, 1 common
140
55.2
153.9
13.9mmUP(2.1mm)
The value in parentheses is the dimension when the base adapter is not used.
4.3 Installation Environment
For details of the installation environment, refer to the user’s manual of the MELSEC-Q series CPU
areas with specifications that are different for the MELSEC-A series and MELSEC-Q series are
Duplication Prohibited
This manual may not be reproduced in any form, in part or in whole, without written permission
from Mitsubishi Electric Engineering Company Limited.
©2014 MITSUBISHI ELECTRIC ENGINEERING COMPANY LIMITED ALL RIGHTS RESERVED
subject to specification restrictions upon replacement. Check the specifications of the
MELSEC is a registered trademark of Mitsubishi Electric Corporation.
for general specifications, refer to the user’s manual of the output module to be used. Those
Conversion Adapter
Do not disassemble or modify the conversion adapter. Doing so could result in failure,
80mA
system
COM
139 to 189N・cm
(fuse blow capacity:50A)}
Note 1. For detailed specifications not stated in the Output Module Specification Comparison Chart and
12/24VDC
Conversion adapter anchor base installation screw (M4 screw)
Available
{6.7A(unchangeable)
available(thermal protect,
short-circuit protect)}
Tightening Torque Range
malfunction.
Zener diode
{protection function
None
Internal current
(4)
Screw Location
Do not touch the terminals during energization. Doing so could result in electric shock or
resistance load)
None
Fuse
(2)
1ms or less
Terminal No. Signal Name
TB1
TB2
TB3
TB4
TB5
TB6
TB7
TB8
TB9
TB10
TB11
TB12
TB13
TB14
TB15
TB16
TB17
TB18
could cause the product to fall or result in a short circuit, product failure or malfunction.
Tighten the module installation screws to the specified torque below. An inappropriate tightening torque
conversion adapter and conversion adapter anchor base damage.
1V (TYP) 0.8A
1.5V (MAX) 0.8A
ON
4.1 Handling Precautions
4A 10ms or less
0.1mA or less
OFF to
5.2 Tightening Torque
(3)
0.5A/point, 4A/common
No limit
(short protect)
4. Mounting and Installation
(1)
12 to 24V DC
0.4A/point(60% ON,55℃)
4A 10ms or less
Surge killer
COM
12/24V DC
0.5A/point, 4A/common
Maximum inrush
current
MELSEC-Q Series
92
Q Series Module
Model
MELSEC-A Series
204
A Series
Module Model
Response time
Conversion Adapter
Model
Model
41.9
2. Conversion Adapter Product Specifications
module to be used.
connection device.
< Output Module Specification Comparison Chart >
Model
MELSEC-A Series
AY51
MELSEC-Q Series
AY51-S1
QY50
Specifications
AY51-UL
No. of input
points
32 points
32 points
16 points
Photocoupler isolation
Photocoupler isolation
Photocoupler isolation
Isolation method
Rated load
3. Products Required by the Conversion Adapter
Please confirm the following product warranty details prior to product use.
(1)
OFF leakage
Response time
Maximum voltage
drop at ON
OFF to
OFF
Surge killer
ERNT-AQF12
12-slot conversion adapter anchor base
590
0.5A/point,
ERNT-AQF8
8-slot conversion adapter anchor base
410
(1A/fuse common)
4A/common
ERNT-AQF5
5-slot conversion adapter anchor base
275
4A 10ms or less
3A 10ms or less
4A 10ms or less
0.1mA or less
0.1mA or less
0.1mA or less
0.9V DC (TYP) 0.5A,
1.5V DC (MAX) 0.5A
1V DC (TYP) 0.3A,
1.5V DC (MAX) 0.3A
0.2V DC (TYP) 0.5A,
0.3V DC (MAX) 0.5A
2ms or less
2ms or less
1ms or less
2ms or less
2ms or less
1ms or less
(resistance load)
(resistance load)
Varistor (52-62V)
Transistor built-in zener
Available
310mA
(TYP. All points ON)
80mA
(TYP. All points ON)
Wiring method for
16-points, 1 common
16-points, 1 common
16-points, 1 common
38-point terminal block
38-point terminal block
18-point terminal
common
system
Base Adapter Model
ERNT-AQB38
ERNT-AQB58
ERNT-AQB35
ERNT-AQB65
block
ERNT-AQB55
MELSEC-A Series
Compliant Module
A38B
A38B-UL
A38B-E
A38HB
A38HBEU
A68B
A68B-UL
A58B
A58B-UL
A35B
A35B-UL
A35B-E
A65B
A65B-UL
ERNT-AQB62
A55B
A55B-UL
A32B
A32B-UL
A32B-E
A62B
ERNT-AQB52
A52B
ERNT-AQB32
4
6
Conversion adapter
The gratis warranty period of this product shall be one (1) year from the date of purchase or delivery to
the designated place.
Note that after manufacture and shipment from MEE, the maximum distribution period shall be six (6)
months, and the gratis warranty period after manufacturing shall be limited to eighteen (18) months.
In addition, the gratis warranty period for repaired products shall not exceed the gratis warranty period
established prior to repair.
MELSEC-A series
terminal block (32 points)
Conversion adapter bottom
installation screw
M3 x 20
1
MELSEC-A series base unit. (Additional hole machining not required)
ERNT-AQB68
Available
4
If any fault or defect (hereinafter referred to as “Failure”) attributable to Mitsubishi Electric Engineering
Company Limited (hereinafter referred to as “MEE”) should occur within the gratis warranty period, MEE shall
repair the product free of charge via the distributor from whom you made your purchase.
Gratis Warranty Period
Precaution
Conversion adapter
anchor base
185
Conversion adapter installation screw
MELSEC-A series
M3 x 30
terminal block
installation screw (M4)
4
4
The base adapter enables MELSEC-Q series installation using the installation holes of the
Zener diode
None
3-slot conversion adapter anchor base
3
2
2
Base Adapter (Sold Separately)
(Rated load,
230mA
(TYP. All points ON)
connection
(2)
resistance load)
Internal current
consumption
External
2
0.3A/point, 2A/common
ERNT-AQF3
Gratis Warranty Terms and Gratis Warranty Range
2
Weight (g)
0.5A/point, 4A/common
diode
Fuse
Type
12 to 24V DC
ON
ON to
Specifications
Conversion Adapter
Anchor Base Model
12/24V DC
current
Mounting bracket (conversion adapter accessory)
Mounting bracket fixing screw
M3.5 x 6 (conversion adapter accessory)
for conversion adapter use. One anchor base is required per base.
12/24V DC
current
Maximum inrush
current
Q series module
Conversion Adapter Anchor Base (Sold Separately)
The conversion adapter anchor base secures the bottom of the conversion adapter and is required
voltage
Maximum load
Product Warranty Details
5. Part Names and Installation Method
Specifications
MELSEC-Q Series Installable Conversion
Compliant Module
Adapter Anchor Base
Q312B
ERNT-AQF12
Q38B
ERNT-AQF8
Weight
(g)
970
5
Secure the conversion adapter anchor base to the base adapter or control panel using the
conversion adapter anchor base installation screws (M4
ERNT-AQF8
870
Q38B
Q35B
ERNT-AQF8
ERNT-AQF5
795
Q68B
Q65B
Q55B
Q65B
Q55B
Q33B
930
790
The gratis warranty range shall be limited to normal use based on the usage conditions, methods and
environment, etc., defined by the terms and precautions, etc., given in the instruction manual, user’s
manual and caution labels on the product.
6
5.1 Installation Method
[1]
Q612B
Q68B
Q68B
Gratis Warranty Range
5
Conversion adapter base installation screw
M4 x 8 (conversion adapter base accessory)
8) provided as an accessory.
(Two end locations)
[2]
655
ERNT-AQF3
675
MEE shall offer product repair services (fee applied) for seven (7) years after production of the product
has been discontinued. Discontinuation of production shall be reported via distributors.
Product supply (including spare parts) is not possible after production has been discontinued.
Secure the mounting bracket to the Q series module using the mounting bracket fixing
screws [M3.5
6 (conversion adapter accessory); two upper/lower locations].
[3]
Mount the conversion adapter onto the mounting bracket.
[4]
Secure the conversion adapter using the conversion adapter installation screws (M3
Exclusion of Opportunity Loss and Secondary Loss from Warranty Liability
30; 4
Precaution
Regardless of the gratis warranty period, MEE shall not be liable for compensation for damages arising from
causes not attributable to MEE, opportunity losses or lost profits incurred by the user due to Failures of MEE
products, damages or secondary damages arising from special circumstances, whether foreseen or
unforeseen by MEE, compensation for accidents, compensation for damages to products other than MEE
products, or compensation for other work carried out by the user.
Before tightening the installation screws, check that the Conversion Adapter has been
securely installed on the MELSEC-Q Series module. Tightening the screws in floating-off
Q63B
Q52B
Q52B
(1)
(2)
locations).
ERNT-AQF5
Warranty Period after Discontinuation of Production
650
state or tilting state will damage the Conversion Adapter installation screws and the
mounting bracket.
505
[5]
The specifications given in the catalogs, manuals and technical documents are subject to change without
notice.
Secure the conversion adapter using the conversion adapter bottom installation screw (M3
20; 2 location).
[6]
Changes in Product Specifications
Secure the MELSEC-A series terminal block to the conversion adapter using the terminal
block installation screws (M4; two upper/lower locations).
This document is a new publication, effective February 2016. Specifications are subject to change without
notice.
Developed February 2016
50CM-D180063-C
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement