Concord v2.5 Rev B Installation Manual

Concord v2.5 Rev B Installation Manual
Installation Instructions
This document describes the installation, programming,
testing, and troubleshooting procedures for installing
Concord security systems with software version 2.5.
&RQFRUG
&RQFRUG5)
ZLWK6RIWZDUH9HUVLRQ
Document Number: 466-1512-01 Rev. B
December 2001
Contents
About This Manual ............................................................ 1
Special Installation Requirements .............................. 1
UL Listed Installations .......................................... 1
Central Station Reporting ...................................... 1
UL Canada Listed Installations ............................. 2
California State Fire Marshall Listed Installations 2
Planning the Installation .................................................... 2
Standard Panel ............................................................ 2
SuperBus 2000 Touchpads ......................................... 2
SuperBus 2000 RF Receivers ..................................... 2
Power Line Carrier Card ............................................ 2
Phone Supervision Card .............................................3
Supervised Wireless Siren .......................................... 3
SuperBus 2000 Phone Interface/Voice Module .......... 3
SnapCards ...................................................................3
SuperBus 2000 8Z Input Module (HIM) .................... 3
SuperBus 2000 4-Relay Output Module (HOM) ....... 3
Interrogator 200 Audio Verification Module ............. 3
SuperBus 2000 Cellular Backup Module ................... 3
SuperBus 2000 Automation Module .......................... 3
Installing the System ......................................................... 3
Determine the Panel Location .................................... 3
Total System Power and Wire Length Guidelines .....4
Mounting the Panel .................................................... 5
Identify Panel Components ............................................... 5
Installing Antennas ..................................................... 6
Connecting the Panel to Earth Ground ....................... 6
Installing the Optional Power Line Carrier Card
(60-755) ...................................................................... 6
Installing the Optional Phone Supervision Card
(60-789) ...................................................................... 6
Installing Optional SnapCards ................................... 7
Connecting Detection Devices to Panel Zone Inputs . 7
Connecting Intrusion Detection Devices ............... 7
Connecting 2-Wire Smoke Detectors .................... 7
Connecting 4-Wire Smoke Detectors .................... 8
Connecting Speakers .................................................. 8
15-Watt Speaker (13-060) ..................................... 9
Hardwire Interior Speaker (60-528) ......................9
Connecting Piezo Sirens .............................................9
Exterior Sirens ....................................................... 9
Interior Sirens ...................................................... 10
Installing Supervised Wireless Sirens (60-736-95) .. 10
Connecting an Interrogator 200 Audio Verification
Module (60-677) ...................................................... 11
Connecting Alphanumeric and Fixed Display
Touchpads .................................................................11
Installing SuperBus 2000 Modules ...........................11
SuperBus 2000 RF Receiver
(60-764-01-95R-16Z/32Z/MAX) ........................12
SuperBus 2000 Phone Interface/Voice Module
(60-777-01) ..........................................................12
SuperBus 2000 Energy Saver Module
(60-620-01) ..........................................................13
SuperBus 2000 8Z Input Module (60-774) .........14
SuperBus 2000 4-Relay Output Module
(60-770) ...............................................................14
SuperBus 2000 Cellular Backup Module .................14
SuperBus 2000 Automation Module ........................15
Setting Device Address on SuperBus 2000 Devices 15
Installing an RJ-31X Phone Jack (13-081) ...............15
Connecting the Phone Line to the Panel with a
DB-8 Cord ................................................................15
Connecting the AC Power Transformer ...................16
Powering Up the Panel .............................................16
Programming the Panel ....................................................16
Entering Program Mode ...........................................17
Touchpad Button Programming Functions ...............17
Moving Through Program Mode Tiers and Menus ..17
Programming Tier 1 Menu Items .............................18
Programming Tier 2 Menu Items .............................19
Using Shortcut Numbers .....................................19
Security Menu .....................................................19
Phones Menu .......................................................21
Phone Options Menu ...........................................25
Timers Menu ........................................................28
Light Control Menu .............................................30
Touchpad Options Menu .....................................30
Reporting Menu ...................................................31
Siren Options Menu .............................................35
Sensors Menu ......................................................36
Audio Verification Menu .....................................38
Accessory Modules Menu ...................................39
Onboard Options Menu .......................................42
Exiting Programming Mode .....................................43
Entering User Programming Mode ...........................44
Time and Date Menu ...........................................44
User Codes Menu ................................................44
Options Menu ......................................................45
Set Up Schedules Menu .......................................46
Attach Schedules to Events Menu .......................47
Energy Saver Menu .............................................48
Attach Lights to Sensors Menu ...........................48
System Version Menu ..........................................49
Downloader Programming .......................................49
ToolBox Downloader Programming ...................49
Testing the System ...........................................................49
Basic System Commands .........................................49
Testing Zones/Sensors ..............................................50
If a Wireless Sensor Does Not Test .....................50
Testing Phone Communication .................................50
Testing Central Station/Pager Communication ........50
Testing Outputs and Sirens .......................................51
Testing Light Control ................................................51
Testing the Energy Saver Module (ESM) .................51
Changing Fixed Display LCD Touchpad Chime and
Trouble Beep Tones ..................................................52
Adjusting Touchpad Display Contrast ..................... 52
Testing Audio Verification Module (AVM)
Communication ........................................................ 52
Testing Cellular Backup Communication ................ 52
Troubleshooting ............................................................... 55
Appendix A: System Planning Worksheets ..................... 61
Appendix B: Reference Tables ....................................... 67
Appendix C: Settings ...................................................... 75
System Wiring Notes....................................................... 81
FCC Notices
FCC Part 15 Information to the User
Changes or modifications not expressly approved by Interlogix Inc. can void the user’s authority to operate the equipment.
FCC Part 15 Class A (Commercial)
This equipment has been tested and found to comply with the limits for a class A digital device, pursuant to part 15 of the FCC rules. These
limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case users will be required to correct the interference at their own expense.
FCC Part 15 Class B (Residential)
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one or more of the following measures:
‰
‰
‰
‰
‰
‰
‰
Install a quality radio or television outdoor antenna if the indoor antenna is not adequate.
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Move the panel away from any wire runs to the affected equipment.
Connect the affected equipment and the panel receiver to separate outlets, on different branch circuits.
Consult the dealer or an experienced radio/TV technician for help.
Send for the FCC booklet How to Identify and Resolve Radio-TV Interference Problems, available from the U.S. Government
Printing Office, Washington, D.C. 20402. Stock Number: 004-000-00345-4.
FCC Part 68
This equipment complies with Part 68 of the FCC Rules. Located on this equipment is a label that contains, among other information, the
FCC registration number and the ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the
telephone company.
The REN is used to determine the maximum number of devices that may be connected to your telephone line. In most areas, the sum of all
device RENs should not exceed five (5.0).
If this equipment causes harm to the telephone network, the telephone company may temporarily disconnect your service. If possible, you
will be notified in advance. When advance notice is not practical, you will be notified as soon as possible. You will also be advised of your
right to file a complaint with the FCC.
Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the proper operation of
your equipment. You will be given advanced notice in order to maintain uninterrupted service.
If you experience trouble with this equipment, please contact the company that installed the equipment for service and repair information.
The telephone company may ask you to disconnect this equipment from the network until the problem has been corrected or you are sure
that the equipment is not malfunctioning.
This equipment may not be used on coin service provided by the telephone company. Connection to party lines is subject to state tariffs.
Declaration of Conformity (DoC)
Interactive Technologies, Inc. declares that the ITI model no. 60-792-95R is in conformity with Part 15 of the FCC Rules. Operation of this
product is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause undesired operation.
Canada Notice
The Canadian Department of Communications label identifies certified equipment. This certification means that the equipment meets certain
telecommunications network protective, operational, and safety requirements. The department does not guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the local telecommunications
company. The equipment must also be installed using an acceptable method of connection. In some cases, the company’s inside wiring associated with a single-line individual service may be extended by means of a certified connector assembly (telephone extension cord). The customer should be aware that compliance with the above conditions may not prevent degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the supplier. Any repairs or
alterations made by the user to this equipment, or equipment malfunctions, may give the telecommunications company cause to request the
user to disconnect the equipment.
For your protection, make sure that the electrical ground connections of the power utility, telephone lines, and internal metallic water pipe
system, if present, are connected together.
Caution
Do not attempt to make connections yourself. Contact the appropriate electrician or electric inspections authority.
The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be connected to a telephone loop that is
used by the device to prevent overloading. The termination on a loop may consist of any combination of devices subject only to the requirement that the total of the LNs of all the devices does not exceed 100. Load Number: 0.2B AC
“AVIS: - L ´étiquette du ministère des Communications du Canada identifie le matériel homologué. Cette étiquette certifie que le matériel
est conforme a certaines normes de protection, d ´ exploitation et de sécurité des réseaux de télécommunications. Le ministère n ´ assure
toutefois pas que le matériel fonctionnera a la satisfaction de l ´ utilisateur.
Avant d ´ installer ce matériel, l ´ utilisateur doit s ´ assurer qu´ il est permis de le raccorder aux installations de l ´ enterprise locale de télécommunication. Le matériel doit également etre installé en suivant une méthod acceptée de raccordement. Dans certains cas, les fils
intérieurs de l´ enterprise utilisés pour un service individuel a ligne unique peuvent etre prolongés au moyen d´ un dispositif homologué de
raccordement (cordon prolongateur téléphonique interne). L ´ abonné ne doit pas oublier qu ´ il est possible que la conformité aux conditions
énoncées ci-dessus n ´ empechent pas le dégradation du service dans certaines situations. Actuellement, les enterprises de télécommunication ne permettent pas que l ´ on raccorde leur matériel a des jacks d ´ abonné, sauf dans les cas précis prévus pas les tarrifs particuliers de
ces enterprises.
Les réparations de matériel homologué doivent etre effectuées pas un centre d ´ entretien canadien autorisé désigné par le fournisseur. La
compagne de télécommunications peut demander a l ´ utilisateur de débrancher un appareil a la suite de réparations ou de modifications
effectuées par l ´ utilisateur ou a cause de mauvais fonctionnement.
Pour sa propre protection, l ´ utilisateur doit s ´ assurer que tous les fils de mise a la terre de la source d ´ énergie électrique, des lignes téléphoniques et des canalisations d ´´ eau métalliques, s ´ il y en a, sont raccordés ensemble. Cette précaution est particulièrement importante
dans les régions rurales.
Avertissment. - L ´ utilisateur ne doit pas tenter de faire ces raccordements lui-meme; il doit avoir recours a un service d ´ inspection
des installations électriques, ou a electricien, selon le cas”.
Une note explicative sur les indices de charge (voir 1.6) et leur emploi, a l ´ intention des utilisateurs du matériel terminal, doit etre incluse
dans l ´ information qui accompagne le materiel homologué. La note pourrait etre rédigée selon le modèle suivant:
“L ´ indice de charge (IC) assigné a chaque dispositif terminal indique, pour éviter toute surcharge, le pourcentage de la charge totale qui
peut etre raccordée a un circuit téléphonique bouclé utilisé par ce dispositif. La terminaison du circuit bouclé peut etre constituée de n ´
import somme des indices de charge de l ´ ensemble des dispositifs ne dépasse pas 100.”
L ´ Indice de charge de cet produit est ____________.
2 2 6 6 S e co n d S t r e e t No r t h
|
N or t h S a i nt Pa u l M n
|
5 5 1 09
|
8 0 0 - 7 77 - 2 6 2 4
|
w w w. i n t e r lo g i x in c .c o m
© 2001 I nte r logix ,™ Inc. ITI , Supe r Bu s, a nd IT I Tool box ar e r egi st er ed t r ade mar ks of I nte r logix , I nc. Int er lo gix , Co ncor d, and Sna pCa rd ar e t r adema rk s of Int e rl ogix , Inc . X- 10 i s a r egi s te r ed t r adem ar k of X - 10 ( USA ) , Inc .
About This Manual
This manual provides information for planning, installing,
programming, and testing this security system. When necessary, this manual refers you to other documentation
included with compatible peripherals.
Planning sheets are included for you to record hardware
layout and software programming settings.
‰
‰
‰
Household Fire Warning System (UL 985)
Basic system, plus:
About the User’s Guide
‰
The User’s Guide (466-1513-01) contains user worksheets
that should be filled out during the installation and programming of the system. With two partition systems, a
User’s Manual for each partition is suggested.
‰
Special Installation Requirements
This security system can be used as a fire warning system,
an intrusion alarm system, an emergency notification system, or any combination of the three.
Some installations may require configurations dictated by
city/state codes, insurance, or Underwriter’s Laboratories
(UL). This section describes the various component and
configuration listings.
ENTRY DELAY set to 45 seconds or less
AC FAILURE set to on
RF TX TIMEOUT set to 24 hours (if system includes a
built in or SuperBus 2000 RF Receiver and wireless
smoke sensors)
‰
‰
‰
‰
‰
‰
Hardwire Smoke Detector:
System Sensor models 2100D, 2100TD, 2100S, 2100TS,
2400, or 2400TH learned into sensor group 26 or Sentrol
(ESL) models 429AT, 521B or 521BXT learned into sensor group 26
Wireless Smoke Sensor 60-506-319.5 or 60-838-95
learned into sensor group 26
IMMEDIATE TROUBLE BEEPS set to on
UL 98 OPTIONS set to on (see page 36)
RECEIVER FAILURE set to on (if wireless devices are
used)
SIREN VERIFY set to on
AC FAILURE set to on
RF TX TIMEOUT set to 4 hours (if system includes a
built in or SuperBus 2000 RF Receiver and wireless
smoke sensors)
UL Listed Installations
UL 1023 & 985 24-Hour Backup
This section describes the requirements for UL Listed
installations.
‰
Basic System
‰
‰
‰
‰
‰
Control Panel (60-734-01 or 60-792-01-95R)
Backup Battery 12V 4 AH (60-681) or 12V 7 AH (60680)
SuperBus 2000 Fixed Display Touchpad (60-820), 2x16
LCD Touchpad (60-746-01), 2x20 LCD Touchpad (60803), or 2x20 VFD Touchpad (60-804)
Standard Class II 24 VAC, 30 VA Power Transformer
(60-761), Class II 24 VAC, 30 VA Line Carrier Power
Transformer (60-762), or Standard Class II 24 VAC, 50
VA Power Transformer (60-778), Class II 24 VAC, 50 VA
Line Carrier Power Transformer (60-779)
Interior Speaker Siren (60-528), Exterior Speaker Siren
(13-060), Slim Line Hardwire Interior Siren (60-483-01)
or Hardwire Exterior Siren (13-046)
Basic system may also include a SuperBus 2000 RF Receiver
(60-764-01-95R-16Z) or (60-764-01-95R-32Z) or
(60-764-01-95R-MAX).
Household Burglary Alarm System Unit (UL 1023)
Basic system, plus:
‰
‰
‰
‰
‰
‰
‰
‰
‰
Hardwire Magnetic Contact (13-068 or 13-071) or
Wireless Learn Mode Door/Window Sensor (60-362)
IMMEDIATE TROUBLE BEEPS set to on
UL 98 OPTIONS set to on (see page 36)
RECEIVER FAILURE set to on (if wireless devices are
used)
SIREN VERIFY set to on
EXIT DELAY set to 60 seconds
QUICK EXIT set to off
EXIT EXTENSION set to off
SIREN TIMEOUT set to 4 minutes or more
Concord
For 24-hour backup, the total current draw for all connected devices is limited to 90 mA (during normal standby
conditions) using a 4.0 AH battery, or 190 mA (during
normal standby conditions) using a 7.0 AH battery.
Commercial Burglary Alarm System Unit
(Grade C UL 1610)
Basic system using Control Panel 60-801-01 plus:
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sensor (60-499)
ITI SAW PIR Sensor (60-639-95R), ITI Crystal PIR Sensor (60-703-95R), or DS924i PIR Sensor (60-511-01-95)
IMMEDIATE TROUBLE BEEPS set to on
UL 98 OPTIONS set to on (see page 36)
RECEIVER FAILURE set to on (if wireless devices are
used)
RF TX TIMEOUT set to 4 hours
24-HOUR TAMPER set to on
SYSTEM TAMPER set to on
AUTO PHONE TEST set to on
PHONE TEST FREQ. set to 1
NEXT PHONE TEST set to 1
SIREN VERIFY set to on
AC FAILURE set to on
UL 1610 24-Hour Backup
‰
Same as UL 1023 & 985
UL 1635 Digital Alarm Communicator System
‰
Same as UL 1023 & 985
Central Station Reporting
The panel has been tested with the following central station
receivers using SIA and Contact ID reporting formats:
‰
ITI CS-5000 Central Station Receiver
1
‰
Sur-Gard Central Station Receiver with models
SG-DRL2A and SG-CPM2
‰
UL Canada Listed Installations
This section describes the requirements for CUL (UL Canada) Listed installations.
‰
Canadian Standards CSA Certified Accessories
‰
Residential Burglary Alarm System Unit
(ULC-S309)
‰
Basic system as described for “UL Listed Installations”
plus:
‰
‰
Hardwire Magnetic Contact (13-068 or 13-071) or Wireless Learn Mode Door/Window Sensor (60-362)
Residential Fire Warning System Control Unit
(ULC-S545-M89)
‰
‰
Basic system as described for “UL Listed Installations”
plus:
‰
‰
‰
‰
Hardwire Smoke Detector:
System Sensor models 2100D, 2100TD, 2100S, 2100TS,
2400, 2400TH learned into Sensor Group 26, or Sentrol
(ESL) models 429AT, 521B, or 521BXT learned into sensor group 26
Wireless Smoke Sensor 60-506-319.5 or 60-838-95
learned into sensor group 26
IMMEDIATE TROUBLE BEEPS set to on
RF TX TIMEOUT set to 4 hours (if system includes
SuperBus 2000 RF Receiver and wireless smoke sensors)
Note
For 24-hour backup, external power drain is limited to 90
mA (during normal standby condition) using a 4.0 AH battery, or 190 mA continuous using a 7.0 AH battery.
‰
SuperBus 2000 Touchpads
The following describes the different touchpads that can be
used for system programming and operation.
‰
‰
California State Fire Marshall Listed Installations
Same as Household Fire Warning System (UL 985), plus:
‰
This section describes system capabilities to help you get
familiar with the system. “Appendix A” provides planning
sheets with tables that let you record the hardware and programming configuration of the system. Fill in all necessary
information ahead of time to help prepare for system installation.
When planning the installation, keep in mind that the panel
has the following capabilities (dependent upon devices
used):
‰
‰
Up to 16 SuperBus 2000 Devices (maximum of 4 RF
receivers)
Up to 76 wireless or hardwired zones
Standard Panel
The following describe the basic panel (out-of-box) hardware capabilities.
‰
2
‰
SMOKE VERIFY must be set to off
Planning the Installation
Power: Input for an AC step-down, plug-in style transformer.
Auxiliary Power Output: Output that supplies 8.5 to
13.5 VDC with up to 1 amp (with panel powered by 30
VA transformer) or 2 amps (with panel powered by 50 VA
transformer) for bus devices and hardwired detectors, such
as smoke and motion detectors.
Bus A and B: Input and output that provides communication between bus devices and the panel.
Siren Driver: Output that can drive an 8-ohm load and
provides intrusion and fire alarm sounds for partition 1.
2 Onboard Outputs: Open-collector outputs that can be
set up to activate other signalling devices, based on system events.
Microphone Input: Input used for 2-way audio when
used in conjunction with the Interrogator 200 Audio Verification Module.
8 Supervised Hardwire Zones: Inputs for various hardwired detectors. Zone 8 can be set up in programming to
accept 2-wire smoke detectors.
Built-In SuperBus 2000 Receiver (60-792-01-95R
only): Allows use of up to 16 or 32 ITI 319.5 MHz. crystal and/or SAW Learn Mode wireless sensors and touchpads. Also allows supervision of Supervised Wireless
Sirens.
Phone Line Connection: Allows panel to communicate
with central monitoring station and/or pagers.
‰
SuperBus 2000 Fixed Display Touchpad: Provides operation control and user-programming access (not installer/
dealer programming). Displays system messages and
indicates system status.
SuperBus 2000 2x16 LCD Touchpad: Provides complete system programming and operation control. Displays system messages that prompt users for information
when needed and indicates system status.
SuperBus 2000 2x20 LCD Touchpad: Provides complete system programming and operation control. Large
display shows system messages that prompt users for
information when needed and indicates system status.
SuperBus 2000 2x20 VFD Touchpad: Provides complete
system programming and operation control. Large fluorescent display shows system messages that prompt users for
information when needed and indicates system status.
SuperBus 2000 RF Receivers
These receivers expand system wireless zone capacity by
16, 32, or the maximum zones allowed by the panel. The
receivers are compatible with all ITI 319.5 MHz. crystal
and SAW Learn Mode wireless sensors, touchpads, and
Supervised Wireless Sirens. You may connect up to 4
receivers to the panel.
Power Line Carrier Card
Adding this card (which requires that the panel be powered
using a Power Line Carrier Transformer) adds the following
capabilities to the system:
‰
‰
Allows the use of Supervised Wireless Sirens.
Allows the use of X-10 Powerhouse Lamp Modules for
light control and light activation during alarms.
Concord
Phone Supervision Card
SuperBus 2000 Cellular Backup Module
Adding this card allows the panel to check for the correct
phone line voltage (partition 1 only), upon dialing the central station/pager number. The panel can also be programmed to check the phone line voltage automatically.
Provides central station communication via cellular transmission as a backup to regular phone line(s).
Supervised Wireless Siren
Provides a connection to a compatible home automation
device.
Supervised Wireless Sirens plug into any standard electrical
outlet and produce status and alarm sounds. The panel sends
signals to the siren through the Power Line Carrier Card and
Line Carrier Power Transformer, through the AC electrical
wiring.
Installing the System
The siren has a built-in transmitter that is used for supervising with the panel. With the siren transmitter learned into
panel memory (panels with receivers), the siren can notify
the panel if it is unplugged, stops receiving panel signals, or
has a low backup battery.
Installing the system consists of the following:
SuperBus 2000 Phone Interface/Voice
Module
This module allows system access and control using touchtone telephones, on- or off-site. The module includes an
output for a speaker that sounds system status and alarm
voice messages.
SnapCards
The following SnapCards expand the system as described:
‰
‰
‰
8Z Input SnapCard: Provides eight additional hardwire
zone inputs, of which two are dedicated for using two wire
smoke detectors.
4 Output SnapCard: Provides four form C relay outputs
that can be set up to activate other signalling devices,
based on system events, schedules, or direct control.
4Z Input/2 Output Combo SnapCard: Provides three
hardwire zone inputs, one two wire smoke detector loop,
and two outputs that can be set up to activate other signalling devices, based on system events, schedules, or direct
control.
SuperBus 2000 8Z Input Module (HIM)
Provides eight additional hardwire zone inputs.
SuperBus 2000 Automation Module
This section describes how to install the system control
panel. Before starting the installation, plan your system layout and programming using the worksheets provided in
Appendix A.
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
Determine the Panel Location
Before permanently mounting the panel, determine panel
location using the following guidelines:
‰
‰
SuperBus 2000 4-Relay Output Module
(HOM)
‰
Provides four form C relay outputs that can be set up to activate other signalling devices, based on system events.
‰
Interrogator 200 Audio Verification
Module
‰
Adding this module allows central station operators to listen-in and talk to occupants on the premises to verify the
emergency when an alarm report is received.
Concord
Determining the Panel Location
Determining Total System Power and Wire Length
Guidelines
Mounting the Panel
Identifying Panel Main Components
Installing the Optional Power Line Carrier Card
Installing Optional SnapCards
Connecting Detection Devices to Panel Zone Inputs
Connecting Speakers
Connecting Piezo Sirens
Connecting an Interrogator 200 Audio Verification
Module
Connecting Alphanumeric and Fixed Display Touchpads
Installing SuperBus 2000 Modules
Installing an RJ-31X Phone Jack
Connecting the Phone Line to the Panel with a DB-8 Cord
Connecting the AC Power Transformer
Powering Up the Panel
‰
‰
Centrally locate the panel with relation to detection
devices whenever possible, to help reduce wire run
lengths and labor.
Locate the panel where the temperature will not exceed
120°F (49°C) or fall below 32°F (0°C).
Avoid running wires parallel with electrical wiring or fixtures such as fluorescent lighting, to prevent wire runs
from picking up electrical noise.
Mount the panel at a comfortable working height (about
45 to 55 inches from the floor to the bottom of the panel,
as shown in Figure 1).
Leave space to the left and right of the panel for wiring,
phone jack, and mounting optional modules.
For wireless panels or hardwire panels that include a
SuperBus 2000 RF Receiver, allow at least 9 inches above
the panel cabinet for antennas.
Allow at least 24 inches in front of the panel to open the
panel door.
3
PHONE JACK AND
OPTIONAL MODULE
MOUNTING AREA
19.25"
12"
ANTENNA
AREA
Table 1: Maximum Device Wire Length and Current
Draw (Continued)
Device
9"
SuperBus 2000 2x20 VFD
Alphanumeric Touchpad
21"
12"
PANEL
NOTE
ALLOW AT LEAST 24"
IN FRONT OF PANEL
45-55" TO ALLOW FOR OPENING
CABINET DOOR AND
ACCESS TO PANEL
COMPONENTS.
FLOOR
Figure 1. Determining Panel Location
Total System Power and Wire Length
Guidelines
Note
(A) Class 2, Class 3, and power-limited fire alarm circuits
must be installed using FPL, FPLR, FPLP, or substitute
cable permitted by the National Electrical Code ANSI/NFPA
70. Wire that extends beyond the cable jacket must be separated from all other conductors by a minimum of 1/4-inch
or by a nonconductive barrier.
Max. Wire
Length to
Panel
22 ga.—250 ft.
18 ga.—600 ft.
Max. mA
Draw
120 mA
SuperBus 2000 Fixed Display 22 ga.—300 ft.
Touchpad
18 ga.—700 ft.
65 mA
SuperBus 2000 RF Receiver
22 ga.—1,100 ft.
18 ga.—2,800 ft.
30 mA
SuperBus 2000 Phone
Interface/Voice Module
22 ga.—40 ft.
18 ga.—120 ft.
600 mA
Power Line Carrier Card
N/A
110 mA
4 Input/2 Output SnapCard
N/A
185 mA*
8Z Hardwire Zone Expander
SnapCard
N/A
230 mA*
4 Output SnapCard
N/A
130 mA*
SuperBus 2000 8Z Input
Module
22 ga.—1,800 ft.
18 ga.—4,000 ft.
35 mA
SuperBus 2000 4-Relay
Output Module
22 ga.—350 ft.
18 ga.—900 ft.
180 mA
SuperBus 2000 Energy Saver 22 ga.—1,600 ft.
Module
18 ga.—4,000 ft.
20 mA
Standard Power:
22 ga.—15 ft.
18 ga.—40 ft.
1600 mA
High Power
22 ga.—10 ft.
18 ga.—30 ft.
1900 mA
SuperBus 2000 Automation
Module
22 ga.—1,500 ft.
18 ga.—4,000 ft.
35 mA
The panel can supply up to 1 amp (1,000 mA) when powered by the 24 VAC, 30 VA transformer or up to 2 amps
(2,000 mA) when powered by the 24 VAC, 50 VA transformer for system devices.
Interrogator 200
22 ga.—3,200 ft.
18 ga.—4,500 ft.
10 mA
Interrogator AVM
22 ga.—110 ft.
18 ga.—260 ft.
300 mA
Wire Length
*Maximum current draw for the SnapCards does not include
the load which may be applied to their auxiliary DC supply.
OR
SuperBus 2000 Cellular
Backup Module
(B) Class 2, Class 3, and power-limited fire alarm circuit
conductors must be installed as Class 1 or higher circuits.
Power
The total system wire length allowed can vary depending on
devices powered by the panel, the wire length between
devices and the panel, and the combined wire length of all
devices.
Table 1 describes the maximum wire length allowed
between compatible devices and the panel, including the
maximum current draw of each device.
Table 1: Maximum Device Wire Length and Current
Draw
Device
Max. Wire
Length to
Panel
Max. mA
Draw
SuperBus 2000 2x16 LCD
Alphanumeric Touchpad
22 ga.—300 ft.
18 ga.—750 ft.
90 mA
SuperBus 2000 2x20 LCD
Alphanumeric Touchpad
22 ga.—250 ft.
18 ga.—600 ft.
120 mA
4
Table 2 describes the total system wire lengths allowed
when installing systems using unshielded or shielded cable.
Table 2: Total System Wire Length Allowed
Wire Type
Total System Wire
18-gauge, unshielded
18-gauge, shielded
4,500 ft.
3,000 ft.
22-gauge, unshielded
22-gauge, shielded
3,500 ft.
2,200 ft.
Table 3 describes the minimum current draw of each device
when the panel is operating only from the backup battery.
For 24-hour backup, the total current draw of all SnapCards
connected to the panel and devices connected to +12V BUS
(panel terminal 4) is limited to 90 mA (during normal
standby condition) using a 4.0 AH battery, or 190 mA (during normal standby condition) using a 7.0 AH battery.
Concord
Mounting the Panel
Table 3: Minimum Device Current Draw
Device
Min. mA
Draw
SuperBus 2000 2x16 LCD Alphanumeric
Touchpad
15 mA
SuperBus 2000 2x20 LCD Alphanumeric
Touchpad
15 mA
SuperBus 2000 2x20 VFD Alphanumeric
Touchpad
15 mA
SuperBus 2000 Fixed Display Touchpad
11 mA
SuperBus 2000 RF Receiver
27 mA
SuperBus 2000 Phone Interface/Voice Module
25 mA
Power Line Carrier Card
N/A
4 Input/2 Output SnapCard
20 mA
8Z Hardwire Zone Expander SnapCard
38 mA
4 Output SnapCard
1 mA
SuperBus 2000 8Z Input Module
18 mA
SuperBus 2000 4-Relay Output Module
12 mA
SuperBus 2000 Energy Saver Module
20 mA
SuperBus 2000 Cellular Backup Module
90 mA
SuperBus 2000 Automation Module
30 mA
Interrogator 200
10 mA
Interrogator AVM
45 mA
Use the following procedure to mount the panel to the wall
or wall studs.
&$87,21
Make sure you are free of static electricity whenever you
work on the panel with the cover open. To discharge any
static, first touch the metal panel chassis, then stay in
contact with the chassis when touching the circuit board.
Using an approved grounding strap is recommended.
To mount the panel:
1.
Open the panel door and remove the necessary wiring
knockouts (see Figure 2). Be careful not to damage the
circuit board.
2.
Feed all wires through wiring knockouts and place the
panel in position against the wall.
3.
Level the panel and mark the top and bottom mounting
holes (see Figure 2).
4.
Install anchors where studs are not present.
5.
Partially insert screws into the two top mounting hole
locations, then hang the panel on the two screws.
6.
Recheck for level, insert the two lower screws, and
tighten all four mounting screws.
M O U N T IN G
H O L E S
After determining panel location, run all necessary wires to
that location using the guidelines in Table 4.
Table 4: Wire Requirements
Device
Wire Requirements
AC Power Transformer 2-conductor, 18-gauge, 25 feet max
Earth Ground
Single conductor, 16-gauge solid, 25
feet max
Telephone (RJ-31X)
4-conductor
Detection Devices
2- or 4-conductor, 18- to 22-gauge,
300-ohms max loop resistance
including device
Speakers
2-conductor, 22-gauge, 175 feet max
2-conductor, 18-gauge, 440 feet max
SuperBus 2000 Devices 4-conductor, 22- or 18-gauge
Interrogator 200 AVM 4-conductor, 22-gauge, shielded
Power and Microphone
2-Wire Smoke
Detectors
Concord
K N O C K O U T S
M O U N T IN G
H O L E S
8573126A.DSF
Figure 2. Mounting the Panel (Hardwire Panel Shown—
Combination Hardwire/Wireless Panel Similar)
Identify Panel Components
Before installing devices and making wiring connections,
familiarize yourself with the main panel components. Figure 3 shows the main component locations for the hardwire
circuit board and Figure 4 shows the main component locations for the combination hardwire/wireless circuit board.
2-conductor, 22-gauge, 330 feet max
2-conductor, 18-gauge, 830 feet max
(based on 10-ohms max loop
resistance plus a 2k-ohm, end-ofline resistor)
5
Hardwire Panel
wire from an earth grounded cold water pipe clamp to the
panel.
BACKUP BATTERY
CONNECTIONS
EEPROM
BLACK RED
POWER LINE
CARRIER CARD
HEADERS
SNAP
CARD
HEADER
MICRO
PROCESSOR
PHONE
SUPERVISION
CARD HEADERS
PROGRAMMING
TOUCHPAD
HEADER
TO WATER PIPE
TERMINAL STRIP
8573G10B.DSF
Figure 3. Hardwire Circuit Board Main Components
GROUND CLAMP
Combination Hardwire/Wireless Panel
BACKUP BATTERY
CONNECTIONS
POWER LINE
CARRIER CARD
HEADERS
EEPROM
RED
SNAP
CARD
HEADER
MICRO
PROCESSOR
PROGRAMMING
TOUCHPAD
HEADER
8573110A.DSF
Figure 6. Connecting the Panel to Earth Ground (Hardwire Panel Shown—Combination Hardwire/
Wireless Panel Similar)
ANTENNA TERMINAL BLOCKS
BLACK
PIPE
PHONE
SUPERVISION
CARD HEADERS
Note
For best results, it is recommended that you crimp a spade
lug on the wire end at the panel and secure the lug under
the circuit board screw as shown in Figure 6.
Installing the Optional Power Line Carrier
Card (60-755)
The Power Line Carrier card lets you add Supervised Wireless Sirens for alarm and status sounds and X-10 Lamp
Modules for controlling lights.
TERMINAL STRIP
8573G206C.DSF
Figure 4. Combination Hardwire/Wireless Circuit Board
Main Components
Installing Antennas
Install the antennas (included with panel) into the inside terminal of each antenna terminal block on the combination
hardwire/wireless panel (see Figure 5).
Install the card on the header pins as shown in Figure 7. No
wiring or programming is necessary.
Note
The lower header has two jumpers installed from the factory that must be removed before installing the Power Line
Carrier Card. Leave these jumpers in place if you are not
installing a Power Line Carrier Card.
POWER LINE CARRIER CARD
MOUNTING LOCATION
CONNECT TO
INSIDE TERMINAL
JUMPERS
TERMINAL STRIP
POWER LINE CARRIER
CARD HEADERS
8573G96A.DSF
Figure 7. Installing the Power Line Carrier Card (Hardwire Panel Shown—Combination Hardwire/
Wireless Panel Similar)
Figure 5. Installing the Antennas
Connecting the Panel to Earth Ground
Installing the Optional Phone Supervision
Card (60-789)
For maximum protection from lightning strikes and transients, connect the lower-left circuit board screw to earth
ground as shown in Figure 6. Use 16-gauge, solid copper
The Phone Supervision Card allows the panel to check the
phone line voltage (partition 1 only), upon dialing the central
station/pager number. The panel can also be programmed to
6
Concord
check the phone line voltage automatically (see “Line Fail
Delay” on page 27).
All eight zones accept either normally open (N/O) or normally closed (N/C) detection devices.
Install the card on the header pins as shown in Figure 8.
Note
The panel comes with factory programmed onboard hardwire zones. Install 2k-ohm, end of line (EOL) resistors on all
unused factory programmed onboard hardwire zones. If
you don’t want to install EOL resistors, delete any unused
zones from memory. See Table 8 on page 37 for onboard
hardwire zone factory programming.
PHONE SUPERVISION
CARD
Connecting Intrusion Detection Devices
Figure 10 shows the typical wiring for N/C and N/O door/
window intrusion detection.
TERMINAL STRIP
P A N E L
T E R M IN A L S
8636G02A.DSF
ZONE
2
GND
ZONE
3
13
14
15
PHONE SUPERVISION
CARD HEADERS
Figure 8. Installing the Phone Supervision Card (Hardwire Panel Shown—Combination Hardwire/
Wireless Panel Similar)
NORMALLY
CLOSED
(N/C)
CONTACTS
IN SERIES
Installing Optional SnapCards
NORMALLY
OPEN
(N/O)
CONTACTS
IN PARALLEL
The SnapCard Header on the right side of the panel allows
for the installation of one SnapCard.
2k Ohm
EOL RESISTOR
49-454
Install the desired SnapCard onto the panel SnapCard
Header and secure it in place with two screws, included
with the card (see Figure 9).
2k Ohm
EOL RESISTOR
49-454
8573G23A.DS4
Figure 10. Connecting N/C and N/O Intrusion Detection
Circuits to the Panel
C O N N E C T O R
S N A P C A R D
S N A P
C A R D
H E A D E R
Figure 11 shows the typical wiring for a Detection Systems
model DS922 (ITI part no. 13-082) motion detector. The
minimum available panel voltage for hardwired PIR motion
detectors is 8.5 VDC (9.5 VDC for UL listed installations).
+ 12
BUS
4
S C R E W
P A N E L
T E R M IN A L S
GND
ZONE
7
20
21
L O C A T IO N S
8573127A.DSF
- +
LP
LN
Figure 9. Installing a SnapCard into the Panel Expansion
Connector (Hardwire Panel Shown—Combination Hardwire/Wireless Panel Similar)
2k Ohm EOL RESISTOR
49-454
(LOCATE AT SENSOR)
Connect all necessary input/output wiring using the
Installation Instructions included with the card.
8 5 7 3 1 4 0 A .D S F
Figure 11. Connecting a Motion Detector to the Panel
Connecting Detection Devices to Panel
Zone Inputs
Zone inputs 1 through 8 are supervised using included 2kohm, end-of-line resistors at the last device on each circuit.
Concord
Connecting 2-Wire Smoke Detectors
Zone input 8 can be set up (in program mode) to accept the
following 12 VDC, 2-wire smoke detectors:
‰
System Sensor models 2100D, 2100TD, 2100S, 2100TS,
7
‰
2400, 2400TH
Sentrol (ESL) models 429AT, 521B, 521BXT—(models
521B and 521BXT require the following dip switch settings: 1-on, 2-off)
part no. 13-360) smoke detectors to panel power and zone 8
input as shown in Figure 13.
Table 5: Panel Minimum Available Power
Min. Voltage/Max. Current Available
&$87,21
Use only the 2-wire smoke detector models described
above. Alarm signals from other detectors may not be
processed correctly if the panel has lost AC power and is
operating only from the backup battery.
8.3 VDC, up to 30 mA total (combined alarm) current
When set up for 2-wire smoke detectors, zone 8 can handle
up to 10 smoke detectors with 120 uA maximum idle current per detector. Maximum total loop current allowed in an
alarm condition is 100 mA.
7.4 VDC, up to 80 mA total (combined alarm) current
Note
When using 2-wire smoke detectors on zone 8, the TWOWIRE SMOKE setting (in program mode) must be turned
on before entering the LEARN SENSORS menu. See
ONBOARD OPTIONS—INPUTS in the section “Programming the Panel” for complete details.
Connect one or more, 2-wire smoke detectors to the panel
as shown in Figure 12.
P A N E L
T E R M IN A L S
ZONE
8
+12V
2W SMK
22
23
8.1 VDC, up to 40 mA total (combined alarm) current
7.7 VDC, up to 60 mA total (combined alarm) current
Note
Zone 8 must be learned into sensor group 26 (fire) for connected smoke detectors to reset after canceling a fire
alarm.
P A N E L
T E R M IN A L S
GND
ZONE
7
ZONE
8
+12V
2W SMK
20
21
22
23
C
C
O
N
O
N
. . . . . M. O. O.
+ +
- -
M
M O D E L
4 4 9 A T
-
+
-
+
C
O
O
C
N
N
. . .- .- M . M . O . O .
+ +
8 5 7 3 G 2 6 A .D S F
2k Ohm
EOL RESISTOR
49-454
(LOCATE AT LAST
DETECTOR)
Figure 12. Connecting 2-Wire Smoke Detectors to the
Panel
2k Ohm
EOL RESISTOR
49-454
(LOCATE AT LAST
DETECTOR)
M O D E L
4 4 9 A T
Connecting 4-Wire Smoke Detectors
Zone input 8 can be used with 4-wire smoke detectors that
latch and remain in the alarm state until power is removed,
then restored to the detector. The panel provides this power
interruption from terminal 23 (2-wire smoke power +), provided that zone 8 is learned into sensor group 26 (fire).
Note
The TWO-WIRE SMOKE setting (in program mode) must
be off when using 4-wire smoke detectors. See ONBOARD
OPTIONS—INPUTS in the section “Programming the
Panel” for complete details.
Table 5 describes the minimum available panel power. Use
only 4-wire smoke detectors that operate at these power
limits. Connect up to five Sentrol (ESL) model 449AT (ITI
8
8 5 7 3 1 3 9 A .D S F
Figure 13. Connecting 4-Wire Smoke Detectors to Panel
Power and Zone 8 Input
Connecting Speakers
The panel provides one siren driver output for intrusion
(steady), fire (temporal 3), and auxiliary (on-off-on-off)
alarm sounds. This output trips only for partition 1 alarms.
The output can drive a single 8-ohm speaker or multiple
speaker circuit of 8-ohms or higher (as shown in the following speaker wiring diagrams). Compatible speakers are
described on the following page.
Concord
&$87,21
To avoid disabling the panel speaker output, do not make
speaker connections with the panel powered up.
15-Watt Speaker (13-060)
Use this speaker for exterior siren applications. Connect the
speaker to the panel as shown in Figure 14.
SPEAKER
SPEAKER
7
7
8
8
NOT
USED
SPLICE
2 8-OHM SPEAKERS
IN SERIES (16 OHMS)
8 5 7 3 G 3 1 A .D S F
Figure 14. Connecting Speakers to the Panel
Hardwire Interior Speaker (60-528)
PANEL
TERMINALS
Use this speaker unit for interior siren applications. Connect
the speaker to the panel as shown in Figure 15.
7
8
SPEAKER
NOT
USED
8573103A.DSF
Figure 16. Connecting Two Hardwire Interior Speaker
w/Dual Speaker Units to Panel Terminals
&$87,21
Connect only the large speaker to panel terminals 7 and 8
as shown. The smaller speaker cannot handle the output
of terminals 7 and 8 and should not be connected, to avoid
damaging the speaker.
Connecting Piezo Sirens
Output 1
Onboard output 1 (OUT 1—terminal 9) is an open-collector
(switched path-to-ground), programmable output that can
handle a maximum of 200 mA current sink. The default setting (01614) activates the output 15 seconds after a police
or fire alarm condition occurs. This allows you to connect a
piezo siren without changing the output configuration number in programming. This output is typically used for exterior siren application.
Output 2
PANEL
TERMINALS
7
8
SPEAKER
NOT
USED
8573102A.DSF
Figure 15. Connecting the Hardwire Interior Speaker w/
Dual Speakers to the Panel
Connect two units to the panel terminals with speakers in series
(16-ohms), as shown in Figure 16.
Onboard output 2 (OUT 2—terminal 10) is an open-collector (switched path-to-ground), programmable output that
can handle a maximum of 200 mA current sink. The default
setting (01710) activates the output for status and alarm
tones, allowing for a piezo siren connection without changing the output configuration number.This output is typically
used for interior siren application.
For more information on output configuration numbers, see
“Onboard Options Menu” on page 42.
Exterior Sirens
Hardwire Exterior Siren (13-046)
Connect the siren to panel as shown in Figure 17.
Concord
9
Installing Supervised Wireless Sirens
(60-736-95)
Supervised Wireless Sirens (SWS) plug
directly into electrical outlets and are not
wired to the panel. The panel (when powered by a line carrier power transformer)
sends alarm and status messages to the
siren, along the building AC wiring.
+12V OUT 1
4
9
P A N E L
T E R M IN A L S
RED
BLACK
8 6 9 0 G 2 6 A .D S F
Figure 17. Connecting the Hardwire Exterior Siren to the
Panel
Interior Sirens
Interior Piezo Siren (30-006)
Connect the piezo siren to the panel terminals with a 2kohm resistor, as shown in Figure 18.
Note
Piezo siren connections to terminal 10 require a 2k resistor
that can be located at the panel, since it does not supervise
the circuit.
If using an external power supply instead of panel terminal
4, the supply voltage must be limited to 9.5 VDC maximum
and the negative side of the power supply must be connected to panel ground (terminal 3).
For supervised operation, the siren has a
built-in transmitter that, when learned into
panel memory, transmits to the panel
receiver if the siren has a low battery or other trouble condition.
Before plugging in Supervised Wireless Sirens, the panel
must be powered up and partition House Codes and the
SWS Supervision Code set (in program mode) to the
desired settings.
The following procedures describe the basic steps for
installing Supervised Wireless Sirens. For complete installation details, refer to the Supervised Wireless Siren Installation Instructions, included with each siren.
Note
Regardless of supervised or unsupervised siren installation, you must follow the order of installation as described
to avoid learning the wrong (or undesired) House Code and
SWS Supervision Code into siren memory.
+12V OUT2
P A N E L
T E R M IN A L S
10
4
For unsupervised wireless siren installations:
2k OHM
RESISTOR
49-454
BLACK
1.
Power up the panel (see “Powering Up the Panel”).
2.
Enter program mode and set the partition House Code
to the desired setting (see the LIGHT CONTROL menu
in the section “Programming the Panel”).
3.
Exit program mode.
4.
Install the siren backup battery.
5.
Plug the siren into an electrical outlet.
6.
Press the STATUS button on any working touchpad.
The siren should beep once and the siren LED should
flash 5 times, indicating it has learned the partition
House Code.
7.
If the siren doesn’t beep or the LED doesn’t flash, reset
the house code on the siren by pressing and holding its
button for 20 seconds. The siren will beep three times
when the memory has been cleared. Repeat step 6.
RED
8 6 9 0 G 2 7 A .D S F
Figure 18. Connecting an Interior Piezo Siren
Slim Line Hardwire Interior Siren (60-483-01)
Connect the siren to the panel as shown in Figure 19.
Note
The volume switch settings inside the siren do not affect the
siren output.
For supervised wireless siren installations:
Note
Hardwire Concord panels must have a SuperBus 2000 RF
Receiver installed for supervised wireless siren operation.
+12V OUT2
1
2
3
HIGH GND LOW
N O T
U S E D
4
10
P A N E L
T E R M IN A L S
1.
Power up the panel (see “Powering Up the Panel”).
2.
Install the siren backup battery.
3.
Clear the siren memory by pressing and holding the
siren button for 20 seconds. The siren will beep three
times when the memory has been cleared.
4.
Enter program mode and set the partition House Code
to the desired setting (see the LIGHT CONTROL menu
in the section “Programming the Panel”).
5.
Proceed to the SIREN OPTIONS menu and set the SWS
Supervision Code to the desired setting.
8 5 7 3 G 2 7 A .D S F
Figure 19. Connecting the Slim Line Hardwire Interior
Siren to the Panel
10
Concord
6.
Proceed to the LEARN SENSORS menu and select the
desired partition, sensor group 33, and the desired sensor number.
7.
When the touchpad display shows TRIP SENSOR nn,
plug the siren into an electrical outlet. The siren should
beep once and the siren LED should flash 10 times,
indicating the panel learned the siren transmitter ID and
that the siren learned both the partition House Code and
SWS Supervision Code.
8.
Connecting Alphanumeric and Fixed
Display Touchpads
Alphanumeric and Fixed Display touchpads use the same
color-coded wire scheme. Connect the touchpads to the
panel power output and bus terminals as shown in Figure
21.
GND
+12V
3
4
A BUS
B
5
6
Exit program mode.
Connecting an Interrogator 200 Audio
Verification Module (60-677)
SUPERBUS 2000
FIXED DISPLAY
TOUCHPAD
OR
LCD ALPHANUMERIC
TOUCHPADS
Connect the Interrogator 200 Audio Verification Module
(AVM) to the panel terminals as shown in Figure 20.
+12V/RED
BUS A/GREEN
BUS B/WHITE
GND/BLACK
Note
When installing Supervised Wireless Sirens for supervised
operation, be sure to program sensor text that clearly identifies each siren. For example, HALLWAY SIREN or BASEMENT SIREN. This can help both you and your customer
locate a specific siren if a problem occurs.
&$87,21
If a speaker is already connected to panel terminals 7 and
8, the Interrogator 200 speaker must be hooked up in
series with that speaker to provide a 16-ohm load.
Hooking up speakers in parallel to panel terminals 7 and 8
creates a 4-ohm load that can cause permanent damage
to the panel.
8690G01A.DSF
Figure 21. Connecting Alphanumeric and Fixed Display
Touchpads to the Panel
Installing SuperBus 2000 Modules
SuperBus 2000 modules can be installed inside the panel
cabinet or away from the panel. Use the following guidelines when installing modules inside the panel cabinet:
‰
‰
‰
Up to 16 bus modules can be connected to the panel. (15
modules for the RF panel since receiver counts as 1.)
Up to 3 of the SuperBus 2000 modules listed in Table 1
(page 4) can be mounted inside the cabinet.
The panel includes two support standoffs you install to
secure module backplates to the panel (see Figure 22).
BLACK
SUPPORT STANDOFF
YELLOW
SPLICE
PANEL
END
RUN SEPARATE
WIRE CABLES
AS SHOWN
MODULE
END
CABLE
SHIELD
PANEL
TERMINALS
7
8
SPEAKER
4
3
11
+12V
GND
MIC
8573101A.DSF
Figure 20. Connecting an Interrogator 200 AVM to the
Panel (Partition 1 use only)
Concord
8573g64A.DSF
Figure 22. Support Standoff
‰
Install the standoffs at the locations shown in Figure 23.
Note
Even if you don’t plan to mount modules inside the cabinet,
install the support standoffs for future use and to avoid losing them.
11
SuperBus 2000 RF Receiver
(60-764-01-95R-16Z/32Z/MAX)
1.
Mount the receiver inside the cabinet enclosure as
shown in Figure 24.
2.
Connect the receiver to the panel as shown in Figure
25.
PANEL
TERMINALS
GND
+12V
3
4
A BUS B
6
5
RECEIVER MODULE
TERMINAL STRIP
SUPPORT
STANDOFFS
+12V
A
B
GND
8573105A.DS4
Figure 25. Connecting the SuperBus 2000 RF Receiver to
the Panel Terminals
8573107A.DSF
Figure 23. Installing the Support Standoffs (Hardwire
Panel Shown—Combination Hardwire/Wireless Panel Similar)
‰
‰
The cabinet has built-in mounting clips on the top and
sides that module backplates slide onto for mounting (see
Figure 23).
One SuperBus 2000 RF Receiver can be installed inside
the cabinet, but it must be mounted on the right-hand side
to accommodate the antennas (see Figure 24). Additional
receivers must be installed outside the cabinet.
TOP
MOUNTING
CLIPS (6)
SIDE
MOUNTING
CLIP
RF
RECEIVER
MODULE
(COVER
REMOVED)
SuperBus 2000 Phone Interface/Voice Module
(60-777-01)
The Phone Interface/Voice Module
includes two backplates for mounting the module inside the control
panel cabinet. The module can also
be mounted outside of the control
panel using an optional plastic housing (part no. 60-800). Refer to the
SuperBus 2000 Phone Interface/
Voice Module Installation Instructions included with each
module, for complete mounting instructions.
8998g18A.DSF
Note
In UL Listed installations, the Phone Interface/Voice Module is for supplementary use only.
The module requires panel power and bus connections,
phone line connection through panel terminals and DB-8
cord (from an RJ-31X jack), and speaker connection
through panel terminals.
Wiring—Power
Connect the module to the panel power and bus terminals as
shown in Figure 26.
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 1
PANEL
CABINET
1
+ 1 2 V
A
2
B
3
4
G N D
5
G N D
6
7
S P K 1 S P K 2
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 2
8
9
1 0
A U D 1 A U D 2 G N D
1 1
T IP 1
1 2
T IP 2
1 3
R IN G
2
1 4
R IN G
1
DETAIL
GND
+12V
3
4
A BUS B
5
P A N E L T E R M IN A L S
SUPPORT STANDOFF
8573G37B.DSF
Figure 24. Mounting SuperBus 2000 Modules Inside the
Cabinet (RF Receiver Shown)
12
6
8573108A.dsf
Figure 26. Connecting the Phone Interface/Voice Module
to the Panel Power and Bus Terminals
Concord
Wiring—Phone Line
Connect the phone line to the module through the panel terminals and DB-8 cord (from an RJ-31X jack) as shown in
Figure 27.
Note
For RJ-31X connections, see “Installing an RJ-31X Phone
Jack (13-081)” on page 15.
3
4
G N D
5
G N D
8
9
1 0
A U D 1 A U D 2 G N D
1 1
T IP 1
GRN
BRN
GRY
RED
24
25
26
27
GREEN
P A N E L
T E R M IN A L S
6
7
S P K 1 S P K 2
1 2
T IP 2
1 3
R IN G
2
A
2
B
3
4
G N D
5
G N D
6
7
S P K 1 S P K 2
8
9
1 0
A U D 1 A U D 2 G N D
1 4
R IN G
1
1 1
T IP 1
1 2
T IP 2
1 3
R IN G
2
1 4
R IN G
1
D W IR E
R IO R
A K E R
2 8
8690G28A.DSF
Figure 28. Connecting an Interior Speaker to the Phone
Interface/Voice Module (Status Messages
Only)
DB-8 CORD
PLUG
BRN
GRY
Wiring—Speaker (Status and Alarm Messages)
Make the following connection only if the Phone Interface/
Voice module is being installed in partition 1 and alarm
sounds are desired from the speaker connected to the terminals. In an alarm situation, the speaker will alternate
between alarm siren tones and voice status messages.
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 2
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 1
RJ-31X
JACK
GRN
H A R
IN T E
S P E
6 0 -5
NOT
USED
RED
B
GRAY
2
BROWN
A
1
+ 1 2 V
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 2
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 1
1
+ 1 2 V
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 2
P H O N E IN T E R F A C E /V O IC E
M O D U L E T E R M IN A L S T R IP 1
RED
8573109A.dsf
Figure 27. Connecting a Phone Line to the Module
1
+ 1 2 V
A
2
B
3
4
G N D
5
G N D
6
7
S P K 1 S P K 2
8
9
1 0
A U D 1 A U D 2 G N D
1 1
T IP 1
1 2
T IP 2
1 3
R IN G
2
1 4
R IN G
1
Wiring—Speaker (Status Voice Messages Only)
Connect an interior speaker to the Phone Interface/Voice
module terminals as shown in Figure 28. When connected
as shown, the speaker only produces status voice messages.
In an alarm situation the speaker will announce voice status
messages.
7
8
P A N E L
T E R M IN A L S
S P E A K E R
H A R
IN T E
S P E
6 0 -5
Note
To prevent status voice messages from being broadcast
outside, do not connect exterior speakers to Phone Interface/Voice module terminals 6 and 7.
NOT
USED
D W IR E
R IO R
A K E R
2 8
8573130A.DSF
Figure 29. Connecting an Interior Speaker to the Phone
Interface/Voice Module (Status and Alarm Messages)
SuperBus 2000 Energy Saver Module (60-620-01)
Connect the Energy Saver Module to the panel and premises thermostat as shown in Figure 30.
Concord
13
SuperBus 2000 4-Relay Output Module (60-770)
ENERGY SAVER MODULE
THERMOSTAT
Connect the SuperBus 2000 4-Relay Output Module to the
panel as shown in Figure 32.
ID: XXXXXXXX
HEAT
1 2 3 4 5 6
OFF
50
60
70
80
90
A/C
TO
HVAC
PANEL
TERMINALS
8573G98A.DSF
GND
+12V
3
4
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
A BUS B
5
6
ZONE COM
ZONE 1
NO 4
COM 4
NC 4
NO 3
COM 3
NC 3
NO 2
COM 2
NC 2
NO 1
COM 1
NC 1
Figure 30. Connecting the Energy Saver Module to the
Panel Terminals and Premises Thermostat
SuperBus 2000 8Z Input Module (60-774)
Connect the SuperBus 2000 8Z Input Module to the panel
as shown in Figure 31.
PANEL
TERMINALS
GND
+12V
3
4
A BUS B
6
5
8690G11A.DSF
Figure 32. Connecting the 4-Relay Output Module to the
Panel Terminals
ID: XXXXXXXX
Connect all necessary output wiring using the Installation
Instructions included with the module.
SuperBus 2000 Cellular Backup Module
Connect the SuperBus 2000 Cellular Backup Module to the
panel as shown in Figure 33.
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ZONE 8
ZONE COMMON
ZONE 7
ZONE 6
ZONE COMMON
ZONE 5
ZONE 4
ZONE COMMON
ZONE 3
ZONE 2
ZONE COMMON
ZONE 1
1 2 3 4 5 6
GND
+12V
3
4
A BUS B
5
Z C O M
Z O N E 1
PANEL
TERMINALS
6
8690G10A.DSF
Figure 31. Connecting the 8Z Input Module to the Panel
Terminals
Connect all necessary input wiring using the Installation
Instructions included with module.
14
8 6 6 4 g 1 0 a .d s f
P A N E L
T E R M IN A L S
G N D
+ 1 2 V
3
4
B U S
A
5
B
6
Figure 33. Connecting the Cellular Backup Module to the
Panel Terminals
Concord
SuperBus 2000 Automation Module
RJ-31X/CA-38A jack:
Connect the SuperBus 2000 Automation Module to the
panel as shown in Figure 34.
1.
Run a 4-conductor cable from the TELCO protector
block to the jack location (see A in Figure 35).
2.
Connect one end of the cable to the jack (see B in
Figure 35).
3.
At the TELCO protector block, remove the premises
phone lines (lines from phone jacks on premises) from
the block and splice them to the black and white (or
yellow) wires of the 4-conductor cable (see C in Figure 35).
4.
Connect the green and red wires from the 4-conductor
cable to the TIP (+) and RING (-) posts on the block
(see D in Figure 35).
A U T O M A T IO N M O D U L E C IR C U IT B O A R D
D B -9 S E R IA L C A B L E
A U T O M A T IO N
D E V IC E
1 2 3 4 5 6
Z C O M
Z O N E 1
G N D
+ 1 2 V
3
4
B U S
A
5
B
6
P A N E L
T E R M IN A L S
8 8 4 5 g 2 0 b .d s f
BRN
GRY
Figure 34. Connecting the SuperBus to the Panel Terminals
Installing an RJ-31X Phone Jack (13-081)
TELCO
PROTECTOR
BLOCK
Use the following guidelines when installing an RJ-31X phone
jack for system control by phone and central station monitoring.
‰ Locate the RJ-31X jack (CA-38A in Canada) no further
than five feet from the panel.
‰ The panel must be connected to a standard analog (loopstart) phone line, that provides 48 volts DC (on-hook or
idle) which increases to 89 to 105 volts DC (ring voltage).
Note
The panel cannot be used on a digital or PBX phone line.
These systems are designed for digital type devices only,
operating anywhere from 5 volts DC and up. The panel
uses an analog modem and does not have a digital converter, adapter, or interface to operate through such systems.
‰
‰
B
RED
When the panel is powered up it automatically assigns
device addresses and unit numbers to SuperBus 2000
devices, enabling the panel and module to communicate.
RED
GREEN
BLACK
GRN
WHITE
(OR YELLOW)
RJ-31X
JACK
Setting Device Address on SuperBus
2000 Devices
TIP
(+)
GREEN
BLACK
GREEN
RING
(-)
D
C
A
RJ-31X
PHONE
LINE
WIRE
RUN
RED
WHITE (OR YELLOW)
RED
LINES FROM
PHONES ON
PREMISES
8573G84A.DSF
Figure 35. Installing an RJ-31X Phone Jack
5.
Check the phones on the premises for dial tone and the
ability to dial out and make phone calls. If phones do
not work correctly, check all wiring and correct where
necessary. Proceed to the “Troubleshooting” section of
this manual if problems persist.
For full line seizure, install an RJ-31X phone jack on the
premises phone line so the panel is ahead of all phones
and other devices on the line. This allows the panel to take
control of the phone line when an alarm occurs, even if the
phone is in use or off-hook.
If an analog line is not available, contact your customer’s
telecommunications specialist and tell him/her you need
an analog line off the phone switch (PBX mainframe) or a
1FB (standard business line).
Connecting the Phone Line to the Panel
with a DB-8 Cord
Note
Connecting the panel to an analog line off the phone switch
places the panel ahead of the phone system, preventing
panel access from phones on the premises. However, the
panel can still be accessed from off-site phones.
To connect the DB-8 cord to the panel terminals and RJ31X jack:
To connect a phone line to the panel using an
Concord
After installing the RJ-31X jack, you are ready to connect
the phone line to the panel. A DB-8 cord (not included) uses
a plug at one end for connecting to the RJ-31X module and
flying leads on the other end for panel terminal connections.
1.
Connect the green, brown, gray, and red flying leads
from the DB-8 cord to panel terminals 24, 25, 26, and
27 (see Figure 36).
15
2.
Insert the DB-8 cord’s plug into the RJ-31X (see
Figure 36).
After connecting and wiring all devices to the panel, you are
ready to apply AC and backup battery power to the panel.
TELCO
HOUSE
GRY
RED
25
26
27
GRAY
To power up the panel:
1.
RED
BRN
24
BROWN
GRN
GREEN
Powering Up the Panel
DB-8 CORD
Connect the red and black battery leads (included with
panel) to the lugs located in the 8).
BACKUP BATTERY CONNECTIONS
PLUG
BLACK RED
BRN
GRY
RJ-31X
JACK
GRN
RED
8573G86A.DSF
BLACK
Figure 36. Connecting the DB-8 Cord to the Panel and
RJ-31X Jack
3.
Check the phones on the premises for dial tone and the
ability to dial out and make phone calls. If phones do
not work correctly, check all wiring and correct where
necessary. Proceed to the “Troubleshooting” section of
this manual if problems persist.
Connecting the AC Power Transformer
The panel must be powered by a plug-in stepdown transformer that supplies 24 VAC, 30 VA (60-761) or 24 VAC,
50 VA (60-778).
BATTERY
8573106A.DSF
Figure 38. Connecting the Backup Battery to the Panel
(Hardwire Panel Shown—Combination Hardwire/Wireless Panel Similar)
2.
Connect the other ends of the battery leads to the battery terminals.
3.
Plug the transformer into an outlet that is not controlled
by a switch.
For systems that include a Power Line Carrier card and
Supervised Wireless Sirens, or X-10 Lamp Modules, the
panel must be powered with the Line Carrier Power Transformer that supplies 24 VAC, 30 VA (60-762) or 24 VAC,
50 VA (60-779).
Alphanumeric touchpads display ************, then SCANNING BUS DEVICES, and finally a date and time display.
Note
If alphanumeric touchpads don’t display anything, immediately unplug the transformer and disconnect the backup
battery. Refer to the “Troubleshooting” section.
Connect the power transformer to the panel as shown in
Figure 37.
4.
&$87,21
Do not plug in the power transformer at this time. The
panel must be powered up using the sequence of steps
described in the next section, “Powering Up the Panel.”
1
2
8573104A.DSF
Figure 37. Connecting a Power Transformer to the Panel
Terminals
16
To permanently mount the transformer, unplug it and
remove the existing screw securing the AC outlet
cover.
WARNING !
Use extreme caution when securing the transformer
to a metal outlet cover. You could receive a serious
shock if a metal outlet cover drops down onto the
prongs of the plug while you are securing the transformer and cover to the outlet box.
24 VAC
PANEL
TERMINALS
RED
5.
Hold the outlet cover in place and plug the transformer
into the lower receptacle.
6.
Use the screw supplied with the transformer to secure
the transformer to the outlet cover.
Programming the Panel
For on-site system programming, an alphanumeric touchpad is required.
Concord
Entering Program Mode
Touchpad Button Programming Functions
Entering program mode is done using an installer/dealer
code (default = 4321). The system can be put into program
mode only when the system is disarmed.
In program mode, touchpad buttons let you navigate to all
installer programming menus for configuring the system.
Table 6 describes the touchpad button functions in program
mode.
To enter program mode:
1.
2.
Press 8 + 4321 + 0 + 0. The touchpad shows
SYSTEM PROGRAMMING.
To enter programming mode using a programming
touchpad:
1.
Connect the red, black, green, and white wires from the
Programming Touchpad Cable (60-791) to the power
and bus wires on an alphanumeric touchpad, matching
the wire colors on each.
2.
Make sure the system is powered up and disarmed.
Note
If the system is powered up after the programming touchpad is connected or if a bus command scan is executed,
the programming touchpad will be “learned” into the system
and must later be manually deleted. See “To delete learned
Unit Numbers:” on page 39.
3.
Table 6: Touchpad Button Functions
Make sure the system is disarmed in all partitions.
Connect the plug on the cable onto the panel programming touchpad header (see Figure 39).
Button
Programming Function
ƒ
Selects menu item or data entry.
‚
Deselects menu item or data entry (if pressed
before #).
A&B
Scroll through available options at the current
menu tier. Also scroll through sensor text
options during sensor text programming.
C
Enters pauses when programming phone
numbers.
D
Deletes certain programmed settings.
0 thru 9
Enter numeric values wherever needed.
1&2
Select off (1) or on (2) wherever needed.
1 thru 6
Press and hold to enter alphabetical
characters A thru F for account numbers.
7&9
Press and hold to enter * (7) or # (9) for
phone numbers.
Moving Through Program Mode Tiers and
Menus
There are two basic tiers of programming menus. Tier 1
menus are accessible immediately after entering program
mode (see Figure 40).
T e s t S y s te m
O ff
W e e k ly
A
p re s s b o th
1
2
3
S ile n t
P a g e r
4
5
6
F e a tu re s
S y s te m
M e n u
7
8
9
S ta tu s
L ig h ts
B y p a s s
0
#
C
p re s s b o th
D
A w a y
N o D e la y
B
p re s s b o th
S ta y
TIER 1
MENUS
System
Programming
#
Figure 39. Connecting a Programming Touchpad
4.
5.
Press 8 + 4321 + 0 + 2. The touchpad sounds one
short beep. Press ‚ and verify that the display shows
SERVICE TOUCHPAD ACTIVE.
Press 8 + 4321 + 0 + 0 and the display shows
SYSTEM PROGRAMMING.
6.
After programming is completed, simply disconnect
the touchpad from the panel header.
Concord
B
A
Demo Kit
OFF/On
B
A
Partition 1
Copy
B
B
Clear Memory
A
A
B
Exit
Programming
Ready
*
FROM TIER 2 MENUS
8690G02A.DSF
TO TIER 2 MENUS
*
PROGRAMMING
TOUCHPAD
CABLE (60-791)
8 5 7 3 1 1 4 A .D S F
Figure 40. Tier 1 Program Menus
Arrows pointing right represent pressing B to advance forward through the menus. Pressing A moves through the
menus in reverse.
The arrow below the SYSTEM PROGRAMMING menu represents pressing ƒ to advance to tier 2 programming
menus. Only when SYSTEM PROGRAMMING is displayed can
you advance to tier 2 menus (see Figure 41).
17
TIER 2
MENUS
Demo Kit Mode
B
B
PHONES
SECURITY
A
#
*
TOUCHPAD
OPTIONS
#
#
*
*
B
B
A
#
B
*
ONBOARD
OPTIONS
A
#
#
A
*
#
B
#
B
A
*
A
#
*
A
*
AUDIO
VERIFICATION
SENSORS
#
(System Programming)
B
LIGHT
CONTROL
TIMERS
SIREN
OPTIONS
A
B
A
*
#
REPORTING
*
ACCESSORY
MODULES
A
#
B
PHONE
OPTIONS
B
A
*
(Default = off) This setting determines whether the panel is
used for a standard installation (off) or as a demo kit (on).
When the Demo Kit option is on, only sensors learned into
groups 01 and 03, duress code use, and phone test (8 +
system master code + 2) will be reported. Turning on this
feature and performing a memory clear changes the following
settings:
Partition 1 Master Code = 1000
B TO SECURITY MENU
Partition 2 Master Code = 2000
A FROM SECURITY MENU
User Code 00 = 1001 (partition 1 code—can also be used to
jump to partition 2)
*
8 6 9 0 G 0 3 A .D S F
Figure 41. Tier 2 Program Menus
Again, arrows pointing right represent pressing B to
advance forward through the menus. Pressing A moves
through the menus in reverse.
Arrows below each menu represent pressing ƒ to advance
to those settings that pertain to that menu. Only when a specific menu is displayed can you advance to those settings.
For example, from the SENSORS menu pressing ƒ gives you
access to learning sensors, programming sensor text, deleting sensors, and viewing/editing sensor programming.
Settings in tier 2 menus can also be accessed by entering
shortcut numbers. See the section, “Programming Tier 2
Menu Items” on page 19 for complete details.
Programming Tier 1 Menu Items
This section guides you through programming tier 1 menu
items as they appear in sequence. The exact order you follow will depend on whether you’re installing a new system
or changing programming in an existing system.
User Code 01 = 1002 (partition 1 code—can also be used to
bypass sensors)
User Code 02 = 2001 (partition 2 code—can also be used for
remote or off-site access)
User Code 03 = 2002 (partition 2 code—can also be used to
perform system tests)
User Code 04 = 1122 (partition 1 code—can also be used to
jump to partition 2, for remote or offsite access, and system tests)
User Code 05 = 1122 (partition 2 code—can also be used to
jump to partition 1, for remote or offsite access, bypassing sensors, and
system tests)
Partition 1 House Code = 255 (P)
Partition 2 House Code = 254 (O)
Zone 1 (hardwire input 1) = Group 10, Front Door
Zone 2 (hardwire input 2) = Group 13, Bedroom Window
Zone 3 (hardwire input 3) = Group 17, Living Room Motion
Sensor
Zone 4 (hardwire input 4) = Group 1, Panic
Zone 5 (wireless, keychain touchpad, ID F00201) = Group 01,
(no text)
Zone 6 (wireless, DWS, ID A00206) = Group 13, Kitchen
Window
COMM FAILURE = off
Demo Kit = on
AVM code = 1212
Entry Delay = 8 sec
Exit Delay = 8 sec
Extended Delay = 1 minute
Siren Timeout = 2 minutes
To turn Demo Kit Mode off or on:
❑
With the display showing DEMO KIT MODE OFF/ON (current
setting), press 1 (off) or 2 (on), then press ƒ.
The display flashes the entered setting, then stops after
pressing ƒ and displays DEMO KIT MODE OFF/ON (new setting).
18
Concord
Using Shortcut Numbers
Partition 1 Copy
(System Programming)
(Default = none) After programming all settings pertaining to
partition 1, you can make an exact copy to use for partition 2.
This helps reduce programming time when the system is set
up for two partitions. If there are certain settings that are
unique to partition 2, simply advance to the appropriate menu
and make the necessary changes.
To go directly to a setting in tier 2, you can enter the shortcut number for that setting. Shortcut numbers in this manual
appear in parenthesis (), under the setting name.
MENU NAME
Downloader Code
LOCATION
(Security-Global)
(0000)
To Copy Partition 1:
❑
With the display showing PARTITION 1
installer code (default = 4321) + ƒ.
press ƒ +
COPY,
The display flashes, then stops after pressing ƒ and shows
DONE.
Clear Memory
(System Programming)
Clearing memory deletes all existing programming
information (except the Dealer Code).
Note
Clearing the memory will erase onboard hardwire zone
factory programming.
To Clear Panel Memory:
With the system in program mode, press A or B until the
display shows CLEAR MEMORY.
Press ƒ and the display shows ENTER CODE TO CLEAR
MEMORY.
Enter the 4-digit installer code (default = 4321) or dealer
code (if programmed) + ƒ. After about five seconds, the
system restarts and the panel scans the bus to learn all bus
devices.
1.
2.
3.
SHORTCUT NUMBER
Shortcut numbers can be used from any setting location
within tier 2.
To advance to tier 2 program menus:
With the system in program mode and the display showing
SYSTEM PROGRAMMING, press ƒ once. The display should
show SECURITY.
Security Menu
The SECURITY menu lets you choose whether security settings affect the whole system (global) or a specific partition.
To access global or partition security menu items:
1.
With the display showing SECURITY, press ƒ. The display should show GLOBAL.
2.
Press ƒ again to advance to global settings, or press A
or B to display PARTITION n, then press ƒ to advance to
selected partition 1 or 2 settings.
If the system doesn’t respond as described, repeat step 3.
The following describes how to program the security settings that appear under GLOBAL.
Programming Tier 2 Menu Items
Downloader Code
(0000)
This section guides you through programming tier 2 menu
items as they appear in sequence. Figure 42 shows the
menus available on tier 2.
TIER 2
MENUS
B
B
A
*
#
TOUCHPAD
OPTIONS
ACCESSORY
MODULES
*
#
*
B
B
A
B
*
ONBOARD
OPTIONS
A
#
A
#
LIGHT
CONTROL
A
*
#
B
SIREN
OPTIONS
A
#
B
TIMERS
*
#
REPORTING
*
#
A
#
B
PHONE
OPTIONS
PHONES
SECURITY
#
B
AUDIO
VERIFICATION
SENSORS
A
*
A
#
*
#
(Default = 12345) The 5-digit downloader code is used in
conjunction with downloader programming. The downloader
operator must have the panel account number and downloader
code in order to perform any programming.
B
To program a Downloader Code:
A
❑
*
B
A
*
(Security-Global)
With the display showing DOWNLOADER CODE nnnnn (current code), enter the desired 5-digit code. The display
flashes the entered code. Press ƒ and the display shows
the new code.
Note
The Downloader Code cannot be deleted or cleared from
panel memory. To change the Downloader Code to its
default setting, enter 12345 in the procedure above.
B TO SECURITY MENU
A FROM SECURITY MENU
*
8 6 9 0 G 0 3 A .D S F
Figure 42. Tier 2 Program Menus
Each menu on tier 2 represents a group of settings related to
the menu name. Some tier 2 menus break down into settings
that affect the whole system (global) or a specific partition.
Concord
19
Installer Code
(0001)
(Security-Global)
(Default = 4321) The 4-digit installer code is used for entering
program mode and changing system settings. If a dealer code
is programmed, only those settings not associated with phone
numbers can be changed.
To program an Installer Code:
❑
With the display showing INSTALLER CODE nnnn (current
code), enter the desired 4-digit code. The display flashes
the entered code. Press ƒ and the display shows the new
code.
Note
The Installer Code cannot be deleted or cleared from
panel memory. To change the Installer Code to its default
setting, enter 4321 in the procedure above.
Dealer Code
(0002)
(Security-Global)
Quick Arm
(Security—Partition 1-2)
(partition 1: 0011, partition 2: 0021)
(Defaults = off) Quick Arm allows system arming without
using an access code. When Quick Arm is on, the system
arming level can be increased from Level 1-OFF to LEVEL
2-STAY, from Level 1-OFF to LEVEL 3-AWAY, or from
Level 2-STAY to LEVEL 3-AWAY, without entering an
access code.
A valid access code is still required to decrease the arming
level or disarm the system.
To turn Quick Arm off or on:
❑
With the display showing QUICK ARM OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Quick Exit
(Security—Partition 1-2)
(partition 1: 0012, partition 2: 0022)
(Default = none) The 4-digit dealer code is used to prevent
unauthorized persons from changing the programmed central
station phone numbers. When this feature is enabled, central
station phone numbers cannot be changed (unless you enter
the program mode by using the dealer code). All other system
settings are still accessible by entering the program mode with
the installer code.
(Defaults = on) This setting determines whether or not users
can open and close a standard entry/exit door without causing
an alarm (while the system is armed).
To program a Dealer Code:
When Quick Exit is on, pressing D on a touchpad (while the
system is armed) starts a 2-minute timer that allows one
standard entry/exit door (sensor groups 10 and 19 only) to be
activated once (opened, then closed).
❑
With the display showing DEALER CODE ✱✱✱✱, enter the
desired 4-digit code. The display flashes the entered
code. Press ƒ and the display shows the new code.
To delete a Dealer Code:
❑
This feature would be useful if the user wants to go out to get
the morning paper while the system is armed. This feature
also allows the user to leave the armed premises without
having to disarm and re-arm the system.
When this feature is turned off, the system must be disarmed
before any protected door is opened.
With the display showing DEALER CODE nnnn (current
code), press D. The display shows DEALER CODE ✱✱✱✱.
Note
The Dealer Code cannot be deleted by clearing panel
memory.
Note
For UL Listed installations, this feature must be set to off.
To turn Quick Exit off or on:
❑
The following sections describe the security settings that
appear under PARTITION 1 and PARTITON 2.
With the display showing QUICK EXIT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Account Number
(Security—Partition 1-2)
(partition 1: 0010, partition 2: 0020)
Exit Extension
(Security—Partition 1-2)
(partition 1: 0013, partition 2: 0023
(Defaults = 00000) The account number is used as panel (or
customer) identification for the central monitoring station.
The panel sends the account number every time it reports to
the central station. Account numbers must be 1 to 10
characters long.
(Defaults = on) This setting determines whether or not the
user can re-enter and exit again through an entry or exit delay
door (without disarming and re-arming the system). This
helps prevent exit faults and false alarms by allowing users to
re-enter the premises for a forgotten item.
Alpha characters A–F can be assigned to the account number
by pressing and holding buttons 1–6 respectively, until the
character appears.
When Exit Extension is on, the panel restarts the exit delay
timer if the user re-enters the premises through a standard
delay door before the standard exit delay time expires.
To program an Account Number:
When this feature is off, the exit delay timer does not restart if
the user re-enters the premises, forcing the user to disarm the
system to avoid setting off an accidental alarm.
❑
20
With the display showing ACCOUNT NUMBER nnnnn (current number), enter the desired account number. The display flashes the entered number. Press ƒ and the display
shows the new number.
To turn Exit Extension off or on:
❑
With the display showing EXIT EXTENSION OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Concord
Auto Stay Arming
(Security—Partition 1-2)
(partition 1: 0014, partition 2: 0024)
Keyswitch Style
(Security—Partition 1-2)
(partition 1: 0016, partition 2: 0026)
(Defaults = on) This setting determines whether or not the
system automatically arms to STAY (level 2) if the user arms
the system to AWAY (level 3) without exiting the premises.
This can help prevent accidental alarms by deactivating
interior motion sensors during occupied arming periods.
(Defaults = transition) This feature allows users to select how
they want the system to behave when armed/disarmed by a
keyswitch sensor. The choices are as follows:
When this feature is on and the system is armed to AWAY,
touchpads (and other status sounders) emit one exit delay
beep every four seconds, then one every second during the
last 10 seconds. If the exit delay time expires with no standard
delay sensor activation, the system automatically arms to
STAY.
Note
Arming the system to “AWAY with No Delay” overrides the
Auto Stay Arming feature.
To turn Auto Stay Arming off or on:
❑
With the display showing AUTO STAY ARMING OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Keyswitch Sensor
(Security—Partition 1-2)
(partition 1: 0015, partition 2: 0025)
(Defaults= none) This feature lets users arm and disarm the
system using either a keyswitch wired to a hardwire zone
input or a wireless door/window sensor.
For example, if sensor 1 is designated as the keyswitch sensor
and the system is disarmed, then tripping sensor 1 could arm
the system to AWAY. If the system is armed to STAY or
AWAY, then tripping the sensor could disarm the system
(depending on keyswitch style).
Note
It is recommended that keyswitch sensors are learned into
group 28.
The panel reports opening, closing, and force armed reports
(if turned on) to the central monitoring station.
Note
A bypassed keyswitch sensor cannot arm or disarm the
system.
During an audible alarm, keyswitch sensors can disarm
the system (which sends a cancel report to the central
monitoring station), but cannot arm the system. The system can be armed only after the siren timeout expires.
Keyswitch sensors test the same as any other sensor and
do not arm or disarm the system during a sensor test.
To assign a Keyswitch Sensor:
❑
With the display showing KEYSWITCH SENSOR nn (current
sensor number), enter the desired sensor number (01–
76). The display flashes the entered sensor number. Press
ƒ and the display shows the new number.
Transition: If keyswitch style is set to transition and the
keyswitch sensor is tripped (opened) when the system is
disarmed (level 1), the panel will automatically arm to AWAY
(level 3). If the sensor is tripped (opened) when the system is
armed to AWAY (level 3) or STAY (level 2), the panel will
automatically disarm.
State: If keyswitch style is set to state, when the keyswitch
sensor is tripped (opened) the panel arms to AWAY (level 3).
If the sensor is restored (closed) the panel disarms.
Opening, closing, and force arming reports (if turned on) are
reported to the central station for both keyswitch styles.
To assign a Keyswitch Style:
❑
With the display showing KEYSWITCH STYLE TRANSITION/
STATE (current setting), press 1 for Transition or 2 for
State. The display flashes the entered setting. Press ƒ
and the display shows the new setting.
Duress Code
(Security—Partition 1-2)
(partition 1: 0017, partition 2: 0027)
(Defaults = none) The duress code is a unique 4-digit access
code that allows users to operate the system and, at the same
time, instructs the panel to send a silent alarm report to the
central station.
Do not use a duress code unless it is absolutely necessary.
Using duress codes often results in false alarms due to code
entry errors. If a duress code is absolutely necessary, use it
with an audio verification module (AVM) to reduce false
alarms and accidental dispatches.
Note
To use this feature, the DURESS OPTION setting under the
REPORTING—PARTITION 1 (2) menu must be turned on.
To program a Duress Code:
❑
With the display showing DURESS CODE ✱✱✱✱, enter the
desired 4-digit duress code. The display flashes the
entered setting. Press ƒ and the display shows the new
code.
To delete a Duress Code:
❑
With the display showing DURESS CODE nnnn (current
code), press D. The display shows DURESS CODE ✱✱✱✱.
Phones Menu
The PHONES menu lets you set up central station reporting
for the system.
The following describes how to program the settings that
appear under CS PHONE 1-3.
To delete a Keyswitch Sensor:
❑
With the display showing KEYSWITCH SENSOR NN (current
sensor number), press D to erase the keyswitch sensor
attribute.
Concord
21
Low Level Rpts
(Phones—CS Phone 1-3)
(cs phone 1: 0102, cs phone 2: 0112, cs phone 3: 0122)
Phone Number
(Phones—CS Phone 1-3)
(cs phone 1: 0100, cs phone 2: 0110, cs phone 3: 0120)
(Defaults = none) This setting is used for programming the
central station receiver phone number. Phone numbers can be
1 to 24 digits long, including pauses or * and # characters.
To enter pauses, press C.
To enter *, press and hold 7 for about two seconds.
To enter #, press and hold 9 for about two seconds.
Note
The PHONE NUMBER menus are not accessible if a Dealer
Code is programmed and the Installer Code is used to
enter installer programming mode. To access these menus
when a Dealer Code is programmed, you must enter
installer programming mode using the Dealer Code.
Call-waiting services should be disabled to prevent interrupting panel communication to the central monitoring station. To program a dialing prefix that disables call-waiting,
see the CALL WAIT CANCEL setting under the menu PHONE
OPTIONS—GLOBAL.
To program a Central Station Phone Number:
❑
With the display showing PHONE NUMBER _ (or current
number), enter the desired phone number. The display
flashes the entered number. Press ƒ and the display
shows the new number.
(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) When
this setting is on, the following non-alarm conditions report to
the central station:
❑ Force Armed
❑ Hardwire Zone Trouble (open or short)
❑ Supervisory (wireless devices)
❑ Low Battery (wireless devices)
❑ Phone Test
❑ Other non-alarm related conditions
To turn Low-Level Reports off or on:
❑
Exception Rpts
(Phones—CS Phone 1-3)
(cs phone 1: 0103, cs phone 2: 0113, cs phone 3: 0123)
(Defaults = off) When this setting is on, the panel reports to
the central station if the system is not armed or disarmed at
the specified schedule times.
To turn Exception Reports off or on:
❑
To delete a Central Station Phone Number:
❑
With the display showing PHONE
ber), press D.
The display shows PHONE
NUMBER
NUMBER
(current num-
_.
High Level Rpts
(Phones—CS Phone 1-3)
(cs phone 1: 0101, cs phone 2: 0111, cs phone 3: 0121)
(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) When
this setting is on, the following conditions report to the central
station:
❑ Fire, Police, Auxiliary, and Duress alarms
❑ No Activity
❑ Receiver Failure (or jam)
❑ Tamper conditions, including Zone Tampers and System
Tamper (40 incorrect key presses or touchpad supervisory)
❑ Entering or exiting Sensor Test mode
❑ Phone Test
With the display showing LOW LEVEL RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
With the display showing EXCEPTION RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Open/Close Rpts
(Phones—CS Phone 1-3)
(cs phone 1: 0104, cs phone 2: 0114, cs phone 3: 0124)
(Defaults = off) This setting determines whether opening and
closing reports are sent to the central station. When turned on,
the panel sends a closing report when the system is armed and
an opening report when the system is disarmed.
Note
To use this feature, the OPENING REPORTS and CLOSING REPORTS settings under the REPORTING menu
must be turned on for that partition.
To turn Opening/Closing Reports off or on:
❑
With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
To turn High-Level Reports off or on:
❑
22
With the display showing HIGH LEVEL RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Concord
Backup
(Phones—CS Phone 1-3)
(cs phone 1: 0105, cs phone 2: 0115, cs phone 3: 0125)
The following describes how to program the phone settings
that appear under PAGER PHONE 1 through 5.
(Defaults: CS Phone 1 = on, CS Phone 2 and 3 = off) This
setting determines whether or not the panel uses another
programmed central station phone number for reporting if
attempts with the first number are unsuccessful.
Phone Number
(Phones—Pager Phone 1-5)
(pager 1: 0130, pager 2: 0140, pager 3: 0150, pager 4:
0160, pager 5: 0170)
When BACK UP is off, the panel will make up to eight
attempts to deliver a report with the programmed phone
number.
(Defaults = none) This setting is used for programming a
phone number that communicates to a pager. Phone numbers
can be 1 to 24 digits long and include pauses, a skylink
number, and 7-digit PIN number.
When BACK UP is set to on, the panel makes up to 16
attempts to deliver the report, alternating between the
programmed phone number and the backup phone number.
CS PHONE 1 is backed up by CS PHONE 2.
CS PHONE 2 is backed up by CS PHONE 1.
CS PHONE 3 is backed up by CS PHONE 1.
To enter pauses, press C.
To enter *, press and hold 7 for about two seconds.
To enter #, press and hold 9 for about two seconds.
Note
Call-waiting services should be disabled to prevent interrupting panel communication to the pager(s). To program a
dialing prefix that disables call-waiting, see the CALL
WAIT CANCEL setting under the menu PHONE
OPTIONS—GLOBAL.
To turn Backup off or on:
❑
With the display showing BACK UP OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To program a Pager Phone Number:
❑
SIA/CID Reporting
(Phones—CS Phone 1-3)
(cs phone 1: 0106, cs phone 2: 0116, cs phone 3: 0126)
(Default = CID) This setting determines whether the panel
uses the SIA or CID (Contact ID) reporting format for central
station communication.
With the display showing PHONE NUMBER _ (or current
number), enter the desired pager phone number. The display flashes the entered number. Press ƒ and the display
shows the new setting.
To delete a Pager Phone Number:
❑
With the display showing PHONE NUMBER (current number), press D. The display shows PHONE NUMBER _.
To select SIA or CID reporting:
❑
With the display showing REPORTING FORMAT SIA/CID (current setting), press 1 (for SIA) or 2 (for CID). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
Cellular Backup
(Phones—CS Phone 1-3)
(cs phone 1: 0107, cs phone 2: 0117, cs phone 3: 0127)
(Defaults: CS Phone 1=on, CS Phone 2 and 3=off) This
setting determines whether the panel uses cellular
communication for reporting if attempts using landline are
unsuccessful.
To turn Cellular Backup off or on:
❑
With the display showing CELLULAR BACKUP, press 1 (for
off) or 2 (for on). The display flashes the entered setting.
Press ƒ and the display shows the new setting.
Concord
High Level Rpts
(Phones—Pager Phone 1-5)
(pager 1: 0131, pager 2: 0141, pager 3: 0151, pager 4:
0161, pager 5: 0171)
(Defaults = on) This setting determines whether the following
alarm conditions report to a pager:
❑ Fire, Police, Auxiliary, and Duress alarms
❑ No Activity
❑ Receiver Failure (or jam)
❑ Tamper conditions, including Zone Tampers and System
Tamper (40 incorrect key presses or touchpad supervisory)
❑ Entering or exiting Sensor Test mode
❑ Phone Test
To turn High-Level Reports off or on:
❑
With the display showing HIGH LEVEL RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
23
Low Level Rpts
(Phones—Pager Phone 1-5)
(pager 1: 0132, pager 2: 0142, pager 3: 0152, pager 4:
0162, pager 5: 0172)
Latchkey Reports
(Phones—Pager Phone 1-5)
(pager 1: 0135, pager 2: 0145, pager 3: 0155, pager 4:
0165, pager 5: 0175)
(Defaults = off) This setting determines whether the following
non-alarm conditions report to a pager:
❑ Force Armed
❑ Hardwire Zone Trouble (open or short)
❑ Supervisory (wireless devices)
❑ Low Battery (wireless devices)
❑ Phone Test
❑ Other non-alarm related conditions
(Defaults = on) This setting determines whether the panel
reports to a pager when the system is armed or disarmed,
according to latchkey time scheduling.
To turn Latchkey reports off or on:
❑
With the display showing LATCHKEY RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To turn Low-Level Reports off or on:
❑
With the display showing LOW LEVEL RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Exception Rpts
(Phones—Pager Phone 1-5)
(pager 1: 0133, pager 2: 0143, pager 3: 0153, pager 4:
0163, pager 5: 0173)
Streamlining
(Phones—Pager Phone 1-5)
(pager 1: 0136, pager 2: 0146, pager 3: 0156, pager 4:
0166, pager 5: 0176)
(Defaults = on) This setting determines whether the panel
includes (off) or excludes (on) the account number when
reporting to a pager.
To turn Streamlining off or on:
❑
(Defaults = off) This setting determines whether the panel
reports to a pager if the system is not armed or disarmed at the
specified schedule times, if open/close reports are turned on.
With the display showing STREAMLINING OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To turn Exception Reports off or on:
❑
With the display showing EXCEPTION RPTS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Open/Close Rpts
(Phones—Pager Phone 1-5)
(pager 1: 0134, pager 2: 0144, pager 3: 0154, pager 4:
0164, pager 5: 0174)
(Defaults = off) This setting determines whether opening and
closing reports are sent to a pager. When turned on, the panel
sends a closing report when the system is armed and an
opening report when the system is disarmed.
Ptn Assignment
(Phones—Pager Phone 1-5)
(pager 1: 0137, pager 2: 0147, pager 3: 0157, pager 4:
0167, pager 5: 0177)
(Defaults = 1) This setting determines the partition that
reports to a pager. Both partitions can be assigned to report to
a single pager.
To set up Partition Assignments for pager reporting:
❑
With the display showing PTN ASSIGNMENT 1/2/12 (current
setting), press 1 or 2 to select partition 1 or 2 (press 1
and 2 to select both partition 1 and 2). The display
flashes the entered setting. Press ƒ and the display
shows the new setting.
Note
To use this feature, the OPENING REPORTS and CLOSING REPORTS settings under the REPORTING menu
must be turned on for that partition.
To turn Opening/Closing Reports off or on:
❑
24
With the display showing OPEN/CLOSE RPTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Concord
The following describes how to program the phone settings
that appear under DOWNLOADER PHONE.
Phone Number
(0180)
(Phones—Downloader Phone)
(Default = none) Use this setting to enter the phone number of
an off-site computer that can be used to program the panel
through the phone line. Phone numbers can be 1 to 24 digits
long, including pauses or * and # characters.
To enter pauses, press C.
To enter *, press and hold 7 for about two seconds.
To enter #, press and hold 9 for about two seconds.
The following describe how to program the phone option
settings that appear under GLOBAL.
Phone Test
(02000)
(Default = on) This setting determines if the user can, at any
time, test the communication from the panel to the central
station or a pager by entering 8 + CODE + 2 (# + 8 + CODE +
2 from a touch-tone phone).
To turn the Phone Test setting off or on:
❑
Note
Call-waiting services should be disabled to prevent interrupting panel communication to the downloader. To program a dialing prefix that disables call-waiting, see the
CALL WAIT CANCEL setting under the menu PHONE
OPTIONS—GLOBAL.
To program a downloader phone number:
❑
With the display showing PHONE NUMBER (current number), enter the desired phone number. The display
flashes the entered number. Press ƒ and the display
shows the new setting.
With the display showing PHONE NUMBER (current number), press D to erase the number. The display shows
PHONE NUMBER_.
Phone Options Menu
With the display showing PHONE TEST OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Auto Phone Test
(02001)
(Phone Options—Global)
(Default = off) This setting determines if the panel sends a
phone test automatically to the central station or a pager on a
predetermined schedule. (Refer to the “Phone Test Freq.” and
“Next Phone Test” settings found under TIMERS—GLOBAL).
To delete a downloader phone number:
❑
(Phone Options—Global)
Note
For U.L. Commercial Listed installations (UL 1610), this
feature must be on.
To turn Automatic Phone Test off or on:
❑
The PHONE OPTIONS menu lets you set up system phone
access and communications that affect the whole system
(global) or a specific partition.
With the display showing AUTO PHONE TEST OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Auto Test Reset
(02002)
(Phone Options—Global)
(Default = on) This setting determines whether or not the
Auto Phone Test interval is reset after any successful report to
the central monitoring station. (Refer to the “Phone Test
Freq.” and “Next Phone Test” settings found under TIMERS—
GLOBAL).
When this feature is on, the panel considers any successful
report to the central monitoring station to be a successful
phone test. Thus, any panel report resets the Next Phone Test
setting to the Phone Test Freq. value. The panel only conducts
an Auto Phone Test if no other reports have been made during
the Phone Test Freq. time period.
When this feature is off, an Auto Phone Test is always
conducted according to the schedule of the Phone Test Freq.
setting, even if the panel makes other reports to the central
monitoring station during that time period.
Note
PHONE TEST FREQ must be set to 2 or higher for this
feature to work.
To turn Auto Test Reset off or on:
❑
Concord
With the display showing AUTO TEST RESET OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
25
Dial Abort Delay
(02006)
Comm Failure
(02003)
(Phone Options—Global)
(Default = on) This setting determines whether the panel
activates trouble beeps to alert users on the premises that
communication to the central station failed. Failure
notification occurs after the third unsuccessful reporting
attempt to the central station/pager.
If a Phone Supervision Card (60-789) is installed, failure
notification can occur immediately if inadequate phone line
voltage is detected upon the initial dialing attempt.
Note
For UL Listed installations, Comm Failure must be turned
on.
(Phone Options—Global)
(Default = 30 sec) This setting determines how much time the
user has to abort a panel report.
To change the Dial Abort Delay:
❑
With the display showing dial abort delay NN SECS (current setting), enter the desired time (15–120s). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
Cancel Message
(02007)
(Phone Options—Global)
To turn Communication Failure notification off or on:
(Default = on) This setting determines whether or not the
panel displays a cancel message after the user disarms the
system to clear an alarm condition.
❑
To turn Cancel Message off or on:
With the display showing COMM FAILURE OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
DTMF Dialing
(02004)
❑
(Phone Options—Global)
(Default = on) This setting determines whether the panel uses
DTMF tones (on) or pulse (off) for dialing programmed phone
numbers.
Pager Delay
(02008)
With the display showing DTMF DIALING OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Note
The Pager Delay time should not be set below 5 seconds,
unless absolutely necessary.
To set the Pager Delay time:
❑
Dialer Abort
(02005)
(Phone Options—Global)
(Default = on) This setting determines whether or not the user
can stop a panel before it sends a false alarm to the central
station.
When this feature is on, alarm reports from sensors in groups
00–20, 34, and 35 can be aborted. To abort the dialing
attempt, the user must enter 1 + user code within the Dialer
Abort Delay time setting (defaulted to 30 sec). Cancel and
restoral reports from these sensor groups are aborted at the
same time. The following reports can also be aborted.
❑ System Alarm Tamper/Cancel
❑ No Activity Alarm/Cancel
❑ Touchpad Police and Auxiliary Panic/Cancel
❑ Recent Closing and Two Trip Error
Note
Fire alarm reports to the central station cannot be aborted.
26
With the display showing DIALER ABORT OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
With the display showing PAGER DELAY nn SECS (current
setting), enter a delay time (0–30). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Call Wait Cancel
(02009)
(Phone Options—Global)
(Default = none) This feature lets you set up a dialing prefix
to disable the call waiting feature before the panel makes its
first dialing attempt to any programmed central monitoring
station or downloader phone number. The prefix can be up to
eight digits.
To enter pauses, press C.
To enter *, press and hold 7 for one second.
To enter #, press and hold 9 for one second.
To set up Call Wait Cancel:
❑
To turn Dialer Abort off or on:
❑
(Phone Options—Global)
(Default = 15 sec) This setting determines how long a report is
delayed to a pager, after the panel dials the pager number.
To turn DTMF Dialing off or on:
❑
With the display showing CANCEL MESSAGE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
With the display showing CALL WAIT CANCEL __ (or current setting), enter the desired prefix. The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
To delete the Call Wait Cancel prefix:
❑
With the display showing CALL
rent setting), press D.
WAIT CANCEL
__ (or cur-
Concord
Dial Tone Detect
(02010)
(Phone Options—Global)
(Default = on) When this setting is on, the panel does not
begin dialing until it detects a dial tone.
When this feature is off, the panel begins dialing a few
seconds after seizing the phone line.
Ring/Hang/Ring
(Phone Options—Partition 1-2)
(partition 1: 0212, partition 2: 0222)
(Defaults = on) This setting determines how the panel picks
up (seizes) the phone line. Select “on” if an answering
machine shares the phone line with the panel. Select “off” if
there is no answering machine sharing the phone line with the
panel.
To set up Dial Tone Detect:
❑
With the display showing DIAL TONE DETECT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
The following sections describe the phone option settings
that appear under PARTITION 1-2.
Note
A Phone Interface/Voice module must be installed for the
system to use the settings under PHONE OPTIONS—
PARTITION 1 and PARTITION 2.
Local Phone Control (Phone Options—Partition 1-2)
(partition 1: 0210, partition 2: 0220)
Note
The REMOTE ACCESS setting must be turned on for this
feature to work.
When this feature is on, the person who is calling the panel
must use the following procedure:
1. Listen for one or two full rings.
2. Hang up.
3. Call the premises again within the next 10–40 seconds.
The system answers after the first ring.
When this feature is off, the system answers after 12 full
rings.
To turn Ring/Hang/Ring access off or on:
With the display showing RING/HANG/RING OFF/ON (current
setting), press 1 (off) or 2 (on). The display begins
flashing the entered selection. Press ƒ and the display
shows the new setting.
(Defaults = on) When this feature is on, the panel can be
accessed from a phone on the premises.
To set up Local Phone Control:
❑
With the display showing LOCAL PHONE CTRL OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Remote Access
(Phone Options—Partition 1-2)
(partition 1: 0211, partition 2: 0221)
Line Fail Delay
(Phone Options—Partition 1 only)
(partition 1: 0213)
(Default = none) This setting determines the amount of time
the partition 1 phone line voltage must be absent before the
panel indicates a phone failure trouble condition. If a delay is
not programmed (default), the panel will not monitor the
phone line voltage.
(Defaults = on) When this setting is on, the panel can be
accessed from an off-site phone.
Note
LINE FAIL DELAY is not available for partition 2 at this
time.
To turn Remote Access off or on:
A Phone Supervision Card must be installed to use this
feature.
❑
With the display showing REMOTE ACCESS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To set the Line Fail Delay time:
1.
2.
With partition 1 selected, press A or B until the display
shows LINE FAIL DELAY nn SECS (current setting).
Enter the desired time value (10–240 seconds). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
To delete the Line Fail Delay time:
1.
2.
Concord
With partition 1 selected, press A or B until the display
shows LINE FAIL DELAY nn SECS (current setting).
Press D to delete the current line fail delay time.
27
Toll Saver
(Phone Options—Partition 1-2)
(partition 1: 0214, partition 2: 0224)
(Defaults = on) This setting determines whether the panel
answers a phone call on the eighth ring (on) or twelfth ring
(off) when a trouble condition exists.
To turn Toll Saver off or on:
1.
2.
With the desired partition selected, press A or B until
the display shows TOLL SAVER OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Phone Panic
(Phone Options—Partition 1-2)
(partition 1: 0215, partition 2: 0225)
Supervisory Time
(0300)
(Timers—Global)
(Default is set randomly between 01:00 and 04:00) This
setting determines what time of day the panel sends
supervisory, low battery, or auto phone test reports to the
central station.
Note
The panel clock must be set with the correct time for accurate supervisory time reporting. See “Time and Date
Menu” on page 44.
To set the Supervisory Time:
❑
(Defaults = off) This setting determines whether or not a
police panic alarm can be activated from a touch-tone phone.
When this feature is on, pressing ƒ + ‚‚‚‚‚‚ from a
touch-tone phone on the premises causes a panic alarm.
With the display showing SUPERVISORY TIME HH:MM (current setting), enter the desired 4-digit time value. For
example, enter 0330 to set the supervisory time for 3:30
A.M. The display flashes the entered setting. Press ƒ and
the display shows the new setting.
To turn Phone Panic off or on:
1.
2.
With the desired partition selected, press A or B until
the display shows PHONE PANIC OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Phone Access Key
(Phone Options—Partition 1-2)
(partition 1: 0216, partition 2: 0226)
RF Tx Timeout
(0301)
(Default = 12 hours) This setting determines how many hours
(2–24) the panel has to receive at least one signal from a
wireless sensor (learned into a supervised group). If the panel
does not receive a signal from any supervised wireless sensor
within the set time, the panel reports a supervisory condition
to the central station.
(Defaults = #) This setting determines which touch-tone
phone button is used for system access and control.
If the Local Phone Control feature is enabled, the user can
pick up the phone and press # (within 5 seconds) to access the
security system. The panel seizes the phone line and waits for
the user to enter system commands. Phone access can be
changed from # to * (see the following note).
Note
Use the default setting (#) to avoid conflicts between the
security system and other phone devices and services.
Many phone devices (such as answering machines, computer modems, and FAX machines) and services (such as
call-waiting, call-forwarding, and some banking transactions) require * to initiate their operation, so using * for this
security feature could cause conflicts.
To change the Phone Access Key:
1.
2.
With the desired partition selected, press A or B until
the display shows PHONE ACCESS KEY #/* (current setting).
Press 1 (for *) or 2 (for #). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Timers Menu
The TIMERS menu lets you set up the various system feature times that affect the whole system (global) or a specific
partition.
(Timers—Global)
Note
For U.L. Listed commercial installations, the RF Tx Timeout must be set to 4 hours. For U.L. Listed residential
installations, the RF Tx Timeout must be set to 24 hours.
To set the RF Tx Timeout:
❑
With the display showing RF TX TIMEOUT nn HOURS (current setting), enter the desired timeout value (2–24). The
display flashes the entered setting. Press ƒ and the display shows the new setting.
Phone Test Freq.
(0302)
(Timers—Global)
(Default = 7 days) This setting determines how often the
panel conducts the automatic phone test (see “Auto Phone
Test” under “Phone Options—Global”). The system can be
set to perform an automatic phone test anywhere from every
day to every 255 days.
Note
For U.L. Commercial Listed installations (UL 1610), this
feature must be set to 1.
To set the Phone Test Freq:
❑
With the display showing PHONE TEST FREQ nnn DAYS
(current setting), enter the number of days (1–255). The
display flashes the entered setting. Press ƒ and the display shows the new setting.
The following describes how to program the timer settings
that appear under GLOBAL.
28
Concord
Next Phone Test
(0303)
(Timers—Global)
(Default = 7 days) This setting is used by the Auto Phone Test
feature (see “Phone Options - Global”) to determine when the
next automatic phone test should occur. This setting should be
the same as, or less than, the Phone Test Freq. setting.
Entry Delay
(Timers—Partition 1-2)
(partition 1: 0310, partition 2: 0320)
(Defaults = 32 sec) This setting determines how much time
the user has to disarm the system (after entering the armed
premises through a “designated delay door”) without causing
an alarm.
Note
For U.L. Commercial Listed installations (UL 1610), this
feature must be set to 1.
Note
For residential UL Listed installations, the Entry Delay
must be set to 45 seconds or less.
To set the Next Phone Test:
To set the Entry Delay:
❑
❑
With the display showing NEXT PHONE TEST nnn DAYS
(current setting), enter the number of days (1–255). The
display flashes the entered setting. Press ƒ and the display shows the new setting.
Output Trip Time
(0304)
(Timers—Global)
(Default = 4 sec) This setting determines how long outputs are
activated when tripped (if they are configured for a
momentary response).
Exit Delay
(Timers—Partition 1-2)
(partition 1: 0311, partition 2: 0321)
(Defaults = 64 sec) This setting determines how much time
the user has (after arming the system) to leave the premises
through a “designated delay door” without causing an alarm.
Note
For residential UL Listed installations, the Exit Delay must
be set to 60 seconds or less.
To set the Output Trip Time:
❑
With the display showing OUTPUT TRIP TIME nn SECS (current setting), enter the number of seconds (1–12). The
display flashes the entered setting. Press ƒ and the display shows the new setting.
Activity Timeout
(0305)
To set the Activity Timeout:
❑
With the display showing ACTIVITY TIMEOUT nn HOURS (current setting), enter the number of hours (1–42). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
Daylight Saving
(0306)
To set the Exit Delay:
❑
(Timers—Global)
(Default = 24 hours) This setting determines when the system
sends a “no activity” report. The panel can be set to wait from
1–42 hours. If no user interaction or device activation occurs
in that time, the panel sends a report to the central station.
(Timers—Global)
(Default = on) When this setting is on, the panel clock
automatically adjusts for daylight saving time changes.
With the display showing ENTRY DELAY nnn SECS (current
setting), enter the desired time value (32–240 using 8second intervals). The display flashes the entered setting.
Press ƒ and the display shows the new setting.
With the display showing EXIT DELAY nnn SECS (current
setting), enter the desired time value (48–184 using 8second intervals). The display flashes the entered setting.
Press ƒ and the display shows the new setting.
Extended Delay
(Timers—Partition 1-2)
(partition 1: 0312, partition 2: 0322)
(Defaults = 4 minutes) This setting determines how much
time the user has (after arming the system) to enter or exit the
premises through a “designated extended delay door” (1–8
minutes).
Note
For UL Listed installations Extended Delay may not be
used.
To set the Extended Delay:
❑
With the display showing EXTENDED DELAY n MINUTES (current setting), enter the desired time value (1–8). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
To turn Daylight Saving off or on:
❑
With the display showing DAYLIGHT SAVING OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
The following sections describe the timer settings that
appear under PARTITION 1-2.
Concord
29
Siren Timeout
(Timers—Partition 1-2)
(partition 1: 0313, partition 2: 0323)
(Defaults = 4 minutes) This setting determines how long
sirens sound (1–30 minutes) if no one is present to disarm the
system.
Note
For UL Listed installations, the Siren Timeout must be set
to 4 minutes or more.
Entry Lights
(Light Control—Partition 1-2)
(partition 1: 0400, partition 2: 0410)
(Defaults = none) This setting determines which X-10 controlled lights turn on during entry and exit delays.
Note
X-10 Lamp Modules set to 1 always turn on during the
entry and exit delays.
To set the Siren Timeout:
❑
X-10 Lamp Modules set to 2 always flash the arming level
when arming the system. For example, lights flash two
times when arming to STAY (level 2), and three times
when arming to AWAY (level 3).
With the display showing SIREN TIMEOUT nn MINUTES (current setting), enter the desired time value (1–30). The
display flashes the entered setting. Press ƒ and the display show the new setting.
To set the Entry Lights:
Sleep Time
(Timers—Partition 1-2)
(partition 1: 0314, partition 2: 0324)
(Defaults = 22:00 (10:00 pm.)) This setting determines the
start time of a 10 hour window during which trouble beeps are
suppressed. The initial occurrence of an event that causes
trouble beeps within this window will not sound trouble beeps
until the Sleep Time window expires. If trouble beeps from a
previous event are due to be restarted during the sleep time
window, they will be restarted one hour prior to Sleep Time.
1.
2.
With the desired partition selected, press ƒ. The display
shows ENTRY LIGHTS nnnnnnn (current setting).
Enter all the desired light numbers (3–9 based on the
UNIT dial setting on each X-10 Lamp Module). The display flashes the entered setting(s). Press ƒ and the display shows the new setting(s).
To delete Entry Lights:
❑
Enter any light number that appears on the display, then
press ƒ. The number disappears from the display.
To set the Sleep Time:
❑
With the display showing SLEEP TIME HH:MM (current setting), enter the desired time value (00:00-23:50 using 10
minute intervals). The display flashes the entered setting.
Press ƒ and the display show the new setting.
Light Control Menu
The LIGHT CONTROL menu lets you set up light activation for a specific partition.
The following describes how to program the light control
settings that appear under PARTITION 1 and PARTITION 2.
Note
For light control to work, X-10 Powerhouse Lamp Modules
must be installed at desired lamps.
House Code
(Light Control—Partition 1, 2)
(partition 1: 0401, partition 2: 0411)
(Defaults: partition 1 = 01-B; partition 2 = 02-C) This setting
enables X-10 controlled lights to work in a selected partition
without interfering with the X-10 controlled lights of the other
partition.
After setting the panel house code for each partition, you must
set the X-10 controlled lights for that partition to the same
house code. The letter that appears automatically after the
house code number indicates the necessary HOUSE dial
setting for X-10 modules in that partition.
To set the House Code:
1.
2.
With the desired partition selected, press A or B until
the display shows HOUSE CODE nn-x (current setting).
Enter the desired number (1–255). The display flashes the
entered number. Press ƒ and the display shows the new
house code.
Touchpad Options Menu
The TOUCHPAD OPTIONS menu lets you set up touchpad
panic and arming operation.
The following section describes the touchpad option settings
that appear under GLOBAL.
30
Concord
Keychain TP Arm (Touchpad Options—Partition 1-2)
(partition 1: 0513, partition 2: 0523)
Latchkey Zones
(0500)
(Touchpad Options—Global)
(Default = none) This setting defines the range of keychain
touchpads that will function as a latchkey user. The value
entered in this section can be any valid zone number. When a
zone number is entered, all zones at or below that zone
number will function as a latchkey user. For example, if 5 is
entered, any keychain touchpads learned into zones 1–5 will
be latchkey users and all others (6–76) will not.
(Defaults = off) When this setting is on, pressing the lock
button on keychain touchpads arms the system directly to
AWAY with NO DELAY.
When this setting is off, each key-press increments the arming
level (i.e., from OFF to STAY, from STAY to AWAY).
To change the Keychain Touchpad Arming setting:
❑
To set the number of Latchkey Zones:
1.
2.
With the display showing LATCHKEY ZONES nnn (current
setting), enter the desired number of latchkey zones
(1–76). The display flashes the entered setting.
Press ƒ and the display shows the new setting.
To delete/disable Latchkey Zones:
❑
With the display showing LATCHKEY
setting), press D.
ZONES
nnn (current
With the display showing KEYCHAIN TP ARM OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Star Is No Delay (Touchpad Options—Partition 1-2)
(partition 1: 0514, partition 2: 0524)
(Defaults = off) This setting determines whether the keychain
touchpad star button controls an output (off) or the NO
DELAY feature (on).
To change the keychain Star Is No Delay setting:
The following sections describe the touchpad option settings that appear under PARTITION 1-2.
❑
Fire Panic
(Touchpad Options—Partition 1-2)
(partition 1: 0510, partition 2: 0520)
(Defaults = on) This setting determines whether touchpad fire
panic buttons are enabled (on) or disabled (off).
To change the Fire Panic setting:
With the display showing FIRE PANIC OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Aux. Panic
(Touchpad Options—Partition 1-2)
(partition 1: 0511, partition 2: 0521)
(Defaults = on) This setting determines whether touchpad
auxiliary panic buttons are enabled (on) or disabled (off).
Reporting Menu
The REPORTING menu lets you set up which system
events are reported to the central monitoring station.
The following describes how to program the reporting settings that appear under GLOBAL.
24-Hour Tamper
(06000)
With the display showing AUXILIARY PANIC OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Police Panic
(Touchpad Options—Partition 1-2)
(partition 1: 0512, partition 2: 0522)
(Reporting—Global)
(Default = off) When this setting is on, the panel sounds
sirens and reports a tamper alarm (even when the system is
disarmed), when wireless sensor tamper switches are
activated.
Note
For commercial UL Listed installations (UL 1610) the 24Hour Tamper must be set to on.
To change the Auxiliary Panic setting:
❑
With the display showing STAR IS NO DELAY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
To turn 24-Hour Tamper off or on:
❑
With the display showing 24 HOUR TAMPER OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
(Defaults = on) This setting determines whether touchpad
police panic buttons are enabled (on) or disabled (off).
To change the Police Panic setting:
❑
With the display showing POLICE PANIC OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Concord
31
Buffer Control
(06001)
(Reporting—Global)
(Default = off) When this setting is on, only arming level
changes are logged in the buffer (memory) of the panel.
When this setting is off, all system events are logged in the
buffer.
(Reporting—Global)
(Default = on) When this setting is on, the panel reports to the
central station when AC and backup battery power are
restored (after an extended power outage).
To turn Back In Service reports off or on:
❑
To turn Battery Restoral reports off or on:
With the display showing BUFFER CONTROL OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Back In Service
(06002)
(Reporting—Global)
(Default = off) When this setting is on, the panel reports to the
central station whenever sensors or zones are bypassed.
With the display showing BYPASS REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Low CPU Battery
(06004)
To turn Buffer Full Report off or on:
❑
Note
For UL Listed installations, the Low CPU Battery feature
must be set to on.
To turn Low CPU Battery reports off or on:
❑
With the display showing LOW CPU BATTERY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
With the display showing BUFFER FULL RPT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Zone Restorals
(06007)
(Reporting—Global)
(Default = off) When this setting is on, the panel reports a
restoral to the central monitoring station for wireless or
hardwire zones in alarm before the alarm is canceled.
Note
As with all ITI panels, hardwire smoke detectors connected to Concord or SnapCard hardwire zones do not
send restorals.
To turn Zone Restoral reporting off or on:
❑
(Reporting—Global)
(Default = on) When this setting is on, the panel reports a low
panel battery to the central station before shutting down.
(Reporting—Global)
(Default = off) When this setting is on, the panel sends an
“event buffer full” report to the central monitoring station
when the event buffer is nearly full.
To turn Bypass Reports off or on:
❑
With the display showing BATTERY RESTORAL OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Buffer Full Rpt
(06006)
With the display showing BACK IN SERVICE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Bypass Reports
(06003)
(Reporting—Global)
(Default = off) If this setting is on, the panel reports to the
central monitoring station when a wireless sensor or touchpad
reports a battery replacement to the panel.
❑
To turn Buffer Control off or on:
❑
Battery Restoral
(06005)
With the display showing ZONE RESTORALS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Two Trip Error
(06008)
(Reporting—Global)
(Default = off) This setting works with the ALARM VERIFY
setting (see “ALARM VERIFY” later in this section and
Appendix B: Table B1, “Sensor Group Characteristics,” on
page 67). If ALARM VERIFY is on, then the panel waits for
a second sensor trip before sending an alarm.
If TWO TRIP ERROR is also on and a second sensor trip
does not occur within a 4-minute time period, then the panel
sends an error report to the central monitoring station.
Note
For UL Listed installations, the Two Trip Error feature must
be set to off.
To turn Two Trip Error off or on:
❑
32
With the display showing TWO TRIP ERROR OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Concord
TP Panic RPT FMT
(06009)
(Reporting—Global)
(Default = off) This setting determines how the panel formats
touchpad panic alarm reports to the central station.
When this feature is turned on, touchpad panic alarms report
using the following 3-digit codes:
Auxiliary—597, Police—598, Fire—599
When turned off, touchpad panic alarms report using a 3-digit
code from 500 to 515, with the last digit identifying the
touchpad device number.
RF Supv Report
(06013)
(Default = weekly) This setting determines whether the panel
sends daily or weekly reports to the central monitoring station
when the panel detects a supervisory condition in a wireless
device.
To set RF Supv Report to daily or weekly:
❑
To turn TP Panic RPT FMT off or on:
❑
With the display showing TP PANIC RPT FMT OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
AC Failure
(06010)
(Reporting—Global)
(Default = off) When this setting is on, the panel reports to the
central station 15 minutes after AC power to the panel is lost.
Note
For UL Listed installations, AC Failure must be set to on.
To turn AC Failure reports off or on:
❑
With the display showing AC FAILURE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Receiver Failure
(06011)
(Reporting—Global)
(Default = off) When this setting is on, the panel reports a
receiver failure under the following conditions:
‰ No wireless sensor signals have been received for two
hours or
‰ The receiver is being jammed with a constant signal.
Note
For UL Listed installations using wireless devices,
Receiver Failure must be set to on.
To turn Receiver Failure reports off or on:
❑
With the display showing RECEIVER FAILURE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
RF Low Bat Rpt
(06012)
(Reporting—Global)
With the display showing RF SUPV REPORT DAILY/WEEKLY
(current setting), press 1 (daily) or 2 (weekly). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
Swinger Limit
(06014)
(Reporting—Global)
(Default = 1) This setting determines the maximum number of
times (1–2) a sensor or zone can go into alarm (during a single
arming period) before the panel automatically bypasses that
sensor or zone. This feature only applies to sensors or zones
in groups 00–20, 29, 34, or 35.
When set to 1, the panel automatically bypasses a sensor or
zone after it causes an alarm. When set to 2, the panel waits
until a sensor or zone has caused a second alarm (during the
same arming period) before bypassing it. At any setting, the
automatic bypass is logged into the event buffer.
A bypassed sensor or zone will be cleared (automatically
unbypassed) if the system receives no further activations from
that sensor or zone over the next 48–50 hours.
Changing the arming level also clears all automatically
bypassed sensors and zones and resets the Swinger Limit
count on all sensors and zones.
To set the Swinger Limit:
❑
With the display showing SWINGER LIMIT n (current setting), press the desired number (1–2). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Program Report
(06015)
(Reporting—Global)
(Default = off) When this setting is on, the panel sends a
report to the central station when someone enters or exits
installer programming.
To turn Program Report on or off:
❑
With the display showing PROGRAM REPORT ON/OFF (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting
(Reporting—Global)
(Default = weekly) This setting determines whether the panel
sends daily or weekly low battery reports to the central
monitoring station when a wireless device is reporting a low
battery condition to the panel.
To set RF Low Battery Report to daily or weekly:
❑
With the display showing RF LOW BAT RPT DAILY/WEEKLY
(current setting), press 1 (daily) or 2 (weekly). The display flashes the entered setting. Press ƒ and the display
shows the new setting.
Concord
33
The following sections describe the settings that appear
under REPORTING—PARTITION 1-2.
Opening Reports
(Reporting—Partition 1-2)
(partition 1: 06100, partition 2: 06200)
(Defaults = off) When this setting is on, the panel sends an
opening report to the central station after disarming the
system.
Note
To use this feature, the OPEN/CLOSE REPORTS settings
under the PHONES menu must be turned on for the specific CS Phone or Pager number.
Duress Option
(Reporting—Partition 1-2)
(partition 1: 06104, partition 2: 06204)
(Defaults = off) When this setting is on, the system can be
controlled using a programmed duress code (see
SECURITY—PARTITION n —DURESS CODE).
Do not use a duress code unless it is absolutely necessary.
Using duress codes often results in false alarms due to code
entry errors. If a duress code is absolutely necessary, use it
with the audio verification module to reduce false alarms and
accidental dispatches.
Note
For UL Listed installations, Duress Option must be set to
off.
To turn Opening Reports off or on:
❑
With the display showing OPENING REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Closing Reports
(Reporting—Partition 1-2)
(partition 1: 06101, partition 2: 06201)
(Defaults = off) When this setting is on, the panel sends a
closing report to the central station after arming the system.
Note
To use this feature, the OPEN/CLOSE REPORTS settings
under the PHONES menu must be turned on for the specific CS Phone or Pager number.
To turn Duress Option off or on:
❑
Force Armed
(Reporting—Partition 1-2)
(partition 1: 06105, partition 2: 06205)
(Defaults = off) When this setting is on, the panel reports to
the central monitoring station when a user “force arms” the
system.
Note
Forced arming occurs if the user presses BYPASS when
arming the system with open sensors or zones protesting.
To turn Closing Reports off or on:
❑
With the display showing CLOSING REPORTS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Recent Closings
(Reporting—Partition 1-2)
(partition 1: 06102, partition 2: 06202)
(Defaults = on) When this setting is on, the panel sends a
recent closing report to the central station if an alarm occurs
within two minutes after the exit delay time expires. Such a
report is used to identify a possible exit fault.
With the display showing DURESS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Auto-forced arming occurs if the user does not press
BYPASS (when arming the system with open sensors/
zones protesting) and the siren time expires.
Auto-forced arming always reports to the central monitoring station.
To turn Force Armed off or on:
❑
With the display showing FORCE ARMED OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To turn Recent Closings off or on:
❑
With the display showing RECENT CLOSINGS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
No Activity
(Reporting—Partition 1-2)
(partition 1: 06103, partition 2: 06203)
(Defaults = off) When this setting is on, the panel sends a no
activity report to the central station when the activity timeout
expires (see TIMERS—ACTIVITY TIMEOUT).
To turn No Activity reports off or on:
❑
34
With the display showing NO ACTIVITY OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Concord
Latchkey Format
(Reporting—Partition 1, 2)
(06106—partition 1, 06206—partition 2)
(Defaults = off) This setting determines whether the selected
partition is set up for basic (off) or advanced (on) latchkey
opening report operation.
Basic:
If the partition is armed by entering 2 (or 3) + CODE,
disarming using a designated latchkey user code or keychain
touchpad within an assigned time schedule sends a page.
If the partition is armed by entering 2 (or 3) + CODE + 6
(LATCHKEY), disarming using a designated latchkey user
code or keychain touchpad inside or outside of an assigned
time schedule sends a page.
Advanced:
If the partition is armed by entering 2 (or 3) + CODE + 6
(LATCHKEY), disarming using a latchkey designated user
code or keychain touchpad within an assigned time schedule
sends a page.
System Tamper
(Reporting—Partition 1-2)
(partition 1: 06109, partition 2: 06209)
(Defaults = off) This setting determines how the panel
handles possible tamper situations. When this feature is on,
the panel reacts in the following two ways:
❑ The system goes into alarm if several attempts are made
to disarm the system with incorrect access codes (40 consecutive keypresses).
❑ The panel reports to the central station if a bus device
stops communicating with the panel.
Note
For UL Commercial Listed installations (UL 1610), System
Tamper must be set to on.
To change the System Tamper setting:
❑
Refer to the User’s Guide for complete Latchkey setup and
operation.
With the display showing SYSTEM TAMPER OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
To turn Latchkey Format off or on:
1.
2.
With the desired partition selected, press A or B until
the display shows LATCHKEY FORMAT OFF/ON (current setting).
Press 1 (off—basic) or 2 (on—advanced). The display
flashes the entered setting. Press ƒ and the display shows
the new setting.
Freeze Alarm
(Reporting—Partition 1, 2)
(06107—partition 1, 06207—partition 2)
(Defaults = off) This setting determines whether the panel
reports a freeze alarm to the central station or pager, when the
selected partition’s energy saver module detects a temperature
that matches a predetermined setting (see BUS DEVICES—
UNIT ID—ENERGY OPTIONS—FREEZE TEMP).
Siren Options Menu
The SIREN OPTIONS menu lets you set up siren operation
and supervision.
The following describes how to program the siren option
settings that appear under GLOBAL.
Immediate Beeps
(0700)
(Default = off) This setting determines whether the panel
activates trouble beeps as soon as a wireless device
supervisory condition is detected (on), or if the panel waits
until “supervisory time” to activate trouble beeps (off). (Refer
to TIMERS—GLOBAL—SUPERVISORY TIME).
Note
For UL Listed installations, this feature must be on.
To turn Freeze Alarm reporting off or on:
1.
2.
With the desired partition selected, press A or B until
the display shows FREEZE ALARM OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
(Siren Options—Global)
To turn Immediate Beeps off or on:
❑
With the display showing IMMEDIATE BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Alarm Verify
(Reporting—Partition 1-2)
(partition 1: 06108, partition 2: 06208)
(Defaults = off) This setting determines whether the panel
reports to the central monitoring station after a single sensor
or zone trip (off) or waits for a second trip before reporting
(on).
This setting affects sensors/zones in groups 10 through 20. If
Alarm Verify is set to on, group 18 responds the same as
group 17 (see “Appendix B, Table B1, “Sensor Group
Characteristics,” on page 67).
Note
For UL Listed installations, Alarm Verify must be set to off.
To turn Alarm Verify off or on:
❑
With the display showing ALARM VERIFY OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
Concord
Disable Trouble Beeps
(0701)
(Siren Options—Global)
(Default = off) When this setting is on, the panel will not beep
to alert users of wireless device supervisory trouble.
Note
For UL Listed installations, Disable Trouble Beeps must
be set to off.
To turn Disable Trouble Beeps off or on:
❑
With the display showing DISABLE TR BEEPS OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
35
UL 98 Options
(0702)
(Siren Options—Global)
(Default = off) This setting determines whether the panel
complies with UL 98 requirements (4-hour trouble beep
restart, 4-hour backup battery test, 4-hour smoke (group 26)
zone supervisory).
Note
For UL Listed installations, this feature must be on.
The following sections describe the settings that appear
under SIREN OPTIONS—PARTITION 1.
Siren Verify
(0710)
(Default = off) This setting determines whether or not the
panel supervises the panel speaker terminals (7–8). When this
feature is on, the panel will indicate a trouble condition if no
speaker is connected to panel speaker terminals.
Note
For UL Listed installations, Siren Verify must be set to on.
To turn UL 98 Options off or on:
❑
With the display showing UL 98 OPTIONS OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
SWS Supv Code
(0703)
To turn Siren Verify off or on:
❑
Sensors Menu
Note
To supervise wireless sirens, Concord hardwire panels
must include a SuperBus 2000 RF Receiver. For all Concord panels, the siren must be learned into sensor group
33 for the system to process radio signals from wireless
sirens.
Supervised Wireless Sirens receive signals from the panel
through the existing electrical wiring. If sirens fail to receive
or process these signals, the siren transmits a wireless signal
to the panel/ receiver.
The SENSORS menu gives you access to the following settings:
‰
‰
‰
‰
Note
You must set both the SWS Supv Code and the partition
House Code (see the LIGHT CONTROL menu) before
plugging in Supervised Wireless Sirens.
To set the SWS Supv Code:
❑
❑
(Siren Options—Global)
(Default = off) This setting determines whether or not sirens
in both partitions sound (on) if either partition activates a fire
alarm.
To turn Global Fire off or on:
❑
With the display showing GLOBAL FIRE OFF/ON (current setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
LEARN SENSORS lets you add (learn) hardwire zones,
wireless sensors, and wireless touchpads into panel
memory.
SENSOR TEXT lets you “name” the sensors and zones you
have added to the system.
DELETE SENSORS lets you delete zones and sensors
from panel memory.
EDIT SENSORS lets you view and, if desired, change a
sensor group or partition assignment. You can also identify whether a zone is wireless or hardwire, whether it is
configured as Normally Closed (N/C) or Normally Open
(N/O), or if the zone is a touchpad.
Table 7: How to Trip Sensors
With the display showing SWS SUPV CODE nnn (current
code), enter the desired code (1–255). The display flashes
the entered code. Press ƒ and the display shows the new
code.
Global Fire
(0704)
With the display showing SIREN VERIFY OFF/ON (current
setting), press 1 (off) or 2 (on). The display flashes the
entered setting. Press ƒ and the display shows the new
setting.
(Siren Options—Global)
(Default = 3) This setting determines the system house code
number used for supervising wireless sirens.
❑
(Siren Options—Partition 1)
❑
❑
❑
❑
❑
Hardwire Zones—Start with the zone in its “normal”
state, then trip the zone into its alarm state. A normally
closed door, for example, should be closed when you
begin the Learn Sensors process. To trip the zone, open
the door.
Wireless Sensors—follow the instructions included with
each sensor.
Wireless Door/Window Sensors with External Contacts—place the external contact in the alarm condition,
then activate the sensor tamper switch.
Self Actuated Bell—activate the tamper switch.
Handheld Wireless Touchpads—press the BYPASS
button.
Keychain Touchpads—press and hold the lock and
unlock buttons together until the touchpad LED flashes.
ELM Keychain Touchpads—
a.) Press and release the unlock button twice quickly,
then press and hold until the LED flashes three times.
b.) Press and release the unlock button once quickly, then
press and hold until the LED flashes two times.
c.) Press and hold the unlock button until the LED
flashes once.
36
Concord
The following describes how to program the sensor settings
that appear under LEARN SENSORS.
Learn Sensors
(080)
(Sensors)
(Default = none) The following describes how to add (learn)
hardwire zones and wireless devices into panel memory.
Note
The panel comes with factory programmed onboard hardwire zones. Install 2k-ohm, end of line (EOL) resistors on
all unused factory programmed onboard hardwire zones.
If you don’t want to install EOL resistors, delete any
unused zones from memory. See Table 8 for onboard
hardwire zone factory programming.
To Learn Sensors into panel memory:
1.
2.
3.
4.
5.
6.
7.
8.
With the display showing SENSORS, press ƒ and the display shows LEARN SENSORS.
Press ƒ and the display shows SENSOR PTN 1.
Press ƒ to select partition 1 or press 2 + ƒ to select partition 2. The display should show SENSOR GROUP 0.
Enter the desired sensor group + ƒ (see Table B1 in
“Appendix B” for a description of all sensor group characteristics). The display shows TRIP SENSOR nn, where nn
is the displayed (next available) sensor number.
To change the displayed sensor number, enter the desired
sensor number + ƒ. The desired sensor number is displayed.
With the desired sensor number displayed, use the guidelines in Table 7 (on page 36) to force the sensor or zone
you are adding (learning) into the panel memory to send a
signal to the panel.
To add another sensor to the same sensor group and partition, go back to step 5.
To add sensors to another sensor group or partition, press
‚ twice and go back to step 1 (LEARN SENSORS).
Note
Sensors must be placed in a partition and group. To
change the sensor group or partition assignment after
adding a sensor or zone, use the EDIT SENSORS menu.
Table 8: Onboard Hardwire Zone Factory
Programming
Zone
Input
Group No. & Description
1
10–Entry/Exit
2
17–Instant Interior Follower
3
13–Instant Perimeter
4
13–Instant Perimeter
5
13–Instant Perimeter
6
13–Instant Perimeter
7
13–Instant Perimeter
8
13–Instant Perimeter
.
Sensor Text
(081)
(Sensors)
(Default = none) Use the following guidelines to “name” zone
and sensor locations:
❑ Use the item numbers that appear in “Appendix B, Table
B2, “Item Numbers and Sensor Text,” on page 69 for
characters and words listed there.
❑ If a desired word does not appear in Table B2, create it
using the characters (custom text).
❑ When using words from Table B2, spaces between them
appear automatically. When using characters from Table
B2 to create words, you must reserve an item number for
a ‘space’ after the word.
❑ Each character or word uses up one item number. For
example, a word from the list counts as one item number.
A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.
❑ Only 16 item numbers are allowed for each zone or sensor name, so plan ahead before programming sensor text.
You may need to abbreviate words to avoid running out
of item numbers.
To program Sensor Text:
1.
2.
3.
4.
Press A or B until the display shows SENSOR TEXT.
Press ƒ and the display shows TEXT FOR SN 01.
Press A or B until the display shows the desired sensor
number (or enter the desired sensor number and press ƒ).
Press ƒ and the display shows:
SN 1 ITEM 0
0 - ________
5.
6.
7.
8.
where ITEM 0 is the first character/word location and 0 is
the character/word number.
Enter the number of the desired character or word, or
scroll through the numbers by pressing B (forward) or A
(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.
Press ƒ to accept the displayed choice and the display
shows:
SN 1 ITEM 1
0 -________
Repeat steps 5 and 6 as needed to complete the zone or
sensor name.
Press ‚ after entering the last character or word number.
The display shows the complete text name. For example:
TEXT FOR SN 01____
FRONT ENTRY DOOR
Note
If the panel memory is cleared, all onboard hardwire
zone factory programming will be erased.
Concord
37
Audio Verification Menu
Delete Sensors
(082)
(Sensors)
(Default = none) The following procedure describes how to
remove hardwire zone and wireless sensor numbers from
panel memory.
Note
Deleting sensors does not delete sensor text associated
with the deleted sensor number. To delete sensor text,
enter the SENSOR TEXT menu and enter 000 (nulls) for
each item number.
3.
Press A or B until the display shows DELETE SENSORS.
Press ƒ and the display shows DELETE SENSOR NN (lowest
zone/sensor number in panel memory).
Press ƒ to delete the displayed sensor or—enter the
desired sensor number, then press ƒ.
Repeat steps 2 and 3 until all desired sensors are deleted.
Edit Sensors
(083)
S01 P1 G13 NC HW
BACK DOOR
where:
S01 = zone/sensor number,
P1 = partition 1,
G13 = sensor group 13,
NC = normally closed,
HW = hardwired, and
BACK DOOR is the programmed text name.
other description codes include:
RF = wireless sensor
TP = touchpad
NO = normally open.
To Edit Sensors:
3.
4.
5.
6.
7.
Audio Verify
(0900)
To turn Audio Verification off or on:
1.
2.
3.
With the display showing AUDIO VERIFICATION, press ƒ.
The display shows PARTITION 1.
Press ƒ again and the display shows AUDIO VERIFY OFF/ON
(current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Press A or B until the display shows EDIT SENSORS.
Press ƒ and the display shows the sensor or zone with
the lowest number.
Press A or B to scroll through all learned zones and
sensors.
When the desired zone or sensor is displayed, press ƒ.
The display shows SENSOR PTN n (current partition
assignment).
Enter the desired partition number, then press ƒ. The display shows the new partition assignment.
Press A or B and the display shows SENSOR GROUP nn
(current group assignment).
Enter the desired group number, then press ƒ. The display shows the new group assignment.
Audio Mode
(0901)
(Audio Verification—Partition 1)
(Default = 1) This setting determines how the audio
verification module operates. Choose one of the following:
❑ (1) Instant—Allows the central station operator instant
access for an audio session by entering the AVM code or
by pressing ‚ (if an AVM access code is not programmed) upon completion of panel alarm report (also
see ACCESS TIMEOUT).
❑ (2) Callback—Allows the central station operator to
contact persons on the premises after one ring and verify
the alarm report. Operator must press ‚ or enter the
AVM access code within 20 seconds after ring. The panel
does not report any alarms during the AVM session,
except for fire alarms.
❑ (3) Callback Silent—Same as Callback, except premises
phones do not ring.
To set Audio Mode:
1.
2.
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows AUDIO MODE nn (current setting).
Enter the desired mode number (1–3). The display flashes
the entered setting. Press ƒ and the display shows the
new setting.
Fire Shutdown
(0902)
(Audio Verification—Partition 1)
(Default = off) This setting determines whether system sirens
turn off during a fire alarm audio session.
To turn Fire Shutdown off or on:
1.
2.
38
(Audio Verification—Partition 1)
(Sensors)
(Default = none) This menu lets you view and, if desired,
change the group and partition assignment for each learned
zone or sensor. For example, the display shows:
1.
2.
The following sections describe the audio verification settings that appear under PARTITION 1.
(Default = off) This setting determines whether or not the
system can be accessed by phone for alarm verification.
To Delete Sensors from panel memory:
1.
2.
The AUDIO VERIFICATION menu lets you set up the
audio verification module (AVM) operation in partition 1. If
you want audio verification for partition 2, you must install
a “stand-alone” audio verification module and a 4-Relay
Output Module (HOM) (60-770) output for that partition.
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows FIRE SHUTDOWN OFF/ON (current
setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Concord
Silent Talkback
(0903)
(Audio Verification—Partition 1)
(Default = off) This setting determines whether the central
station operator can speak to persons on the premises (on) or
only listen (off) during a silent or duress alarm audio session.
To turn Silent Talkback off or on:
1.
2.
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows SILENT TALKBACK OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Access Timeout
(0904)
The ACCESSORY MODULES menu gives you access to the
following menus:
‰
‰
To change the Access Timeout:
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows ACCESS TIMEOUT nn SECS (current setting).
2. Enter the desired time. The display flashes the entered
setting. Press ƒ and the display shows the new setting.
1.
Note
Most settings under ACCESSORY MODULES—BUS
DEVICES have no shortcut numbers.
Unit - ID
(10000 thru 10015)
To identify bus device Unit and ID:
1.
where 0 is the Unit Number and 02110185 is the
Device ID number.
Note
To help identify bus devices, the 8-digit Device ID number
is also located on a label on each SuperBus 2000 device.
To change the Beep Delay:
1.
(Audio Verification—Partition 1)
(Default = ✱✱✱✱ or none) This setting determines the code
required to access the audio verification module to start an
audio session. If no code is programmed, pressing ‚ starts an
audio session.
With the display showing BUS DEVICES, press ƒ. The display shows the bus Unit Number and the 8-digit Device
ID number. For example:
UNIT - ID
0—02110185
(Default = 02 sec) This setting determines how long AVM
access beeps are delayed (0–300s, in 2-second intervals) at
the beginning of a 2-way audio session.
Access Code
(0906)
(Acc. Modules—Bus Devices)
(Default = none) This menu lets you identify all connected
bus devices, view each Unit Number, view the Device ID
number, and configure other settings based on a specific
device. This menu also lets you delete learned bus devices.
(Audio Verification—Partition 1)
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows BEEP DELAY nn SECS (current
setting).
2. Enter the desired time. The display flashes the entered
setting. Press ƒ and the display shows the new setting.
BUS DEVICES—this menu lets you read bus device unit
numbers, assign bus devices to a partition, and configure
other features associated with a specific bus device.
SNAPCARDS—this menu lets you set the configuration
number for each SnapCard output, assign SnapCard outputs to a partition, and name the SnapCard outputs.
The following procedure describes how to program the settings that appear under ACCESSORY MODULES—BUS
DEVICES.
(Audio Verification—Partition 1)
(Default = 90 sec) If the Audio Mode is set to “Instant,” then
this setting determines how much time (30–300s, in 2-second
increments) the central station operator has to enter the AVM
access code after the panel is accessed for an audio session.
Beep Delay
(0905)
Accessory Modules Menu
2.
Press A or B to identify all other bus Unit Numbers (0–
15) and Device ID numbers.
To delete learned Unit Numbers:
1.
2.
3.
With the display showing BUS DEVICES, press ƒ. The display shows the bus device set to Unit Number 0.
Press A or B until the bus device Unit Number you want
to delete is displayed.
Press D. The display changes the Unit Number to NONE.
To change the Access Code:
1. With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows ACCESS CODE nnnn (current
code).
2. Enter the desired 4-digit access code. The display flashes
the entered code. Press ƒ and the display shows the new
setting.
To delete an Access Code:
With the display showing AUDIO VERIFY OFF/ON, press A or
B until the display shows ACCESS CODE nnnn (current
code).
2. Press D to delete.
1.
Concord
39
Device ID
(Acc. Modules—Bus Devices
—Unit ID—Change ID)
(Default = none) This menu lets you change the bus device ID
number when replacing a defective bus device.
To change a Device ID:
1.
2.
3.
4.
5.
6.
With the display showing the desired bus device, press ƒ
+ ƒ. The display shows DEVICE ID (current ID).
Enter the ID of the new bus device. The display flashes
the entered selection. Press ƒ and the display shows the
new setting.
Exit programming mode.
Remove AC and battery power from the panel.
Replace the defective bus device with a new one.
Apply AC and battery power to the panel.
Partition Assign
Output Programming
Use these settings to program the output points of any
installed SuperBus 2000 Hardwire Output Module. The
installer programs a HOM output point into the Concord
security panel by entering three kinds of information.
1. Partition: the system partition (1 or 2).
2. Trigger: the event that activates the output point. Trigger
events can be partition alarms, trouble conditions, open
sensors, etc. (see Appendix B: Reference Tables).
3. Response: how the output responds when trigger event
occurs (see Appendix B: Reference Tables).
This section describes how to program each of the HOM
output point configurations into the security panel. The point
configuration number is tttrr, where ttt is the trigger number
and rr is the response number.
Note
HOM output points cannot be configured for user control.
Only the onboard and SnapCard outputs can be configured for user control.
(Acc. Modules—Bus Devices
—Unit ID—Device Partition)
(Default = 1) This menu lets you assign bus devices to work
in the desired partition.
Note
SuperBus 2000 8Z Input Modules, SuperBus 2000 4Relay Output Modules, and SuperBus 2000 RF Receivers
are not assigned to partitions.
1.
2.
3.
4.
To assign bus devices to partitions:
1.
With the display showing the desired bus device, press
ƒ.
2. Press A or B until the display shows DEVICE PTN and then
press ƒ. The display shows PARTITION ASSIGN n.
3. Press 1 or 2 to select the desired partition. The display
flashes the entered selection. Press ƒ and the display
shows the new setting.
(Acc. Modules—
—Unit ID—Outputs)
5.
6.
7.
8.
With the display showing the desired bus device, press
ƒ.
Press A or B until the display shows OUTPUTS.
Press ƒ. The display shows OUTPUT 1.
Press A or B to select an output, then press ƒ. The display shows PARTITION ASSIGN 1.
Press 1 or 2 to select the desired partition assignment
for this relay. The display flashes the entered setting.
Press ƒ and the display shows the new setting.
Press A or B. The display shows CONFIGURATION tttrr (current setting).
Enter the desired 5-digit configuration number for this
relay. The display flashes the entered setting. Press ƒ and
the display shows the new setting.
Press ƒ and repeat steps 4 through 8 until all outputs are
programmed
Status Beeps
(Acc. Modules—Bus Devices
—Unit ID—Keypad Options)
(Default = on) This setting determines whether or not the
selected touchpad sounds status beeps. Each touchpad can be
set individually.
This feature is usually turned off for a touchpad that is located
in or near bedrooms, to avoid disturbing sleeping persons.
Note
For UL Listed installations, Status Beeps must be set to
on.
To turn touchpad Status Beeps on or off:
1.
2.
3.
40
With the display showing the desired touchpad, press ƒ
then A or B until the display shows KEYPAD OPTIONS.
Press ƒ and the display shows STATUS BEEPS OFF/ON
(current setting).
Press 1 (off) or 2 (on) to select the desired setting. The
display flashes the entered selection. Press ƒ and the display shows the new setting.
Concord
Key Beeps
(Acc. Modules—Bus Devices
—Unit ID—Keypad Options)
(Default = on) This setting determines whether or not selected
touchpads beep when their buttons are pressed.
This feature is usually turned off for a touchpad that is located
in or near bedrooms, to avoid disturbing sleeping persons.
To turn Key Beeps on or off:
1.
2.
With the display showing the desired touchpad, press ƒ
then A or B until the display shows KEYPAD OPTIONS.
Next, press ƒ then A or B until the display shows KEY
BEEPS OFF/ON (current setting).
Press 1 (off) or 2 (on) to select the desired setting. The
display flashes the entered selection. Press ƒ and the display shows the new setting.
Cellular System
(Acc. Modules—Bus Devices
—Unit ID—Cellular Options)
(Default = B) This setting determines the cellular transmission
system (A or B) used for cellular communication. This
information is provided by the cellular provider based on
installation ZIP code.
To set the Cellular System:
1.
With the display showing the desired bus device press 1,
(B) or 2 (A). The display flashes the entered selection.
Press ƒ and the display shows the new setting.
The following describes how to program the settings that
appear under SNAPCARDS.
Output Programming
Freeze Temp
(Acc. Modules—Bus Devices
—Unit ID—Energy Options)
(Default = 42°F) This setting determines the temperature
point that the Energy Saver Module detects a potential freeze
(heating failure) condition. The adjustable range is from 40°
to 90°F.
To change the Freeze Temp setting:
1.
2.
With the display showing the desired bus device press ƒ,
then A or B until the display shows ENERGY OPTIONS.
Next, press ƒ then A or B until the display shows
FREEZE TEMP nn DEGREES (current setting).
Enter the desired freeze temperature (40°–90° F). The
display flashes the entered selection. Press ƒ and the display shows the new setting.
Temperature
(Acc. Modules—Bus Devices
—Unit ID—Energy Options)
(Default = none) This setting lets you adjust the Energy Saver
Module (ESM) room temperature setting to match the
premises thermostat. The adjustable range is from 40°–90°F.
Note
To ensure accuracy, wait at least 15 minutes before setting
the ESM temperature to allow the ESM to warm or cool to
actual room temperature.
To change the ESM Temperature setting:
1.
2.
With the display showing the desired bus device press ƒ,
then A or B until the display shows ENERGY OPTIONS.
Next, press ƒ and then A or B until the display shows
TEMPERATURE nn DEGREES (current setting).
Enter the desired temperature (40°–90° F). The display
flashes the entered selection. Press ƒ and the display
shows the new setting.
(Acc. Modules—SnapCards
—Output Programming)
(101001—output 1, 101011—output 2, 101021—output
3, 101031—output 4)
(Defaults: Partition Assign = all 1, Configuration Output 1 =
01400, Output 2 = 00410, Output 3 = 00903, Output 4 =
01003)
This setting lets you assign a partition and a 5-digit
configuration number for each SnapCard relay output. This
number determines both which system event activates the
output and the duration or time the output is activated.
1. Partition: the system partition (1 or 2).
2. Configuration number: The combination of a trigger and
a response.
Trigger: the event that activates the output point. Trigger events can be partition alarms, trouble conditions,
open sensors, etc. (see Appendix B: Reference
Tables).
Response: how the output responds when trigger
event occurs (see Appendix B: Reference Tables).
This section describes how to program each of the output
point configurations into the security panel. The point
configuration number is tttrr, where ttt is the trigger number
and rr is the response number.
To assign configuration numbers to SnapCard Relay
outputs:
1.
2.
3.
4.
5.
6.
7.
Concord
With the display showing SNAPCARDS, press ƒ. Then
press A or B until the display shows OUTPUT PROGRAMMING.
Press ƒ again and the display shows OUTPUT 1.
Press A or B to select the desired output (1–4), then
press ƒ.
With the display showing PARTITION ASSIGN 1, press 1 or
2 to select the desired partition. Press ƒ to confirm the
partition.
Press A or B until the display shows CONFIGURATION tttrr
(current setting).
Enter the desired 5-digit configuration number for this
relay. Press ƒ to confirm the setting.
Press ƒ and repeat steps 3 through 6 until all outputs are
programmed.
41
Output Text
(Acc. Modules—SnapCards
—Output Text)
(10110—output 1, 10111—output 2, 10112—output 3,
10113—output 4)
(Defaults = none) Entering text for an output allows the user
to control it directly or by schedule. Use the following
guidelines to “name” SnapCard outputs:
❑ Use the item numbers that appear in “Appendix B, Table
B2” for characters and words listed there.
❑ If a desired word does not appear in Table B2, create it
using the characters (custom text).
❑ When using words from Table B2, spaces between them
appear automatically. When using characters from Table
B2 to create words, you must reserve an item number for
a ‘space’ after the word.
❑ Each character or word uses up one item number. For
example, a word from the list counts as one item number.
A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.
❑ Only 16 item numbers are allowed for each output name,
so plan ahead before programming output text. You may
need to abbreviate words to avoid running out of item
numbers.
Note
If you desire an output for User Output Control you must
use the Output Text feature to name the output. If no Output Text is programmed, the user will not have access to
the output.
To program Output Text:
1.
2.
3.
4.
With the display showing SNAPCARDS, press ƒ, then A or
B until the display shows OUTPUT TEXT.
Press ƒ and the display shows OUTPUT 1.
Press A or B until the desired output number is displayed.
Press ƒ and the display shows:
OUTPUT N ITEM
0
0 - ________
5.
6.
where ITEM 0 is the first character/word location and 0 is
the character/word number.
Enter the number of the desired character or word, or
scroll through the numbers by pressing B (forward) or A
(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.
Press ƒ to accept the displayed choice and the display
shows:
1
0 Repeat steps 4 and 5 as needed to complete the output
name.
Press ‚ after entering the last character or word number.
The display shows the complete text name. For example:
OUTPUT PROGRAMMING—This menu lets you set configuration numbers for the two built-in panel outputs and
assign the outputs to partitions.
OUTPUT TEXT—This menu lets you assign text to the output allowing the output to be controlled by the user.
The following sections describe the settings that appear
under ONBOARD OPTIONS—INPUTS
Smoke Verify
(1100)
(Onboard Options—Inputs)
(Default = off) This setting determines whether the panel
requires one alarm signal (off) or two alarm signals within
five minutes (on) before activating system sirens and
reporting to a central station. This setting affects 2-wire
smoke detectors connected to a SnapCard zone input or any
other hardwire zone learned into sensor group 26 (FIRE).
Note
For California State Fire Marshall (CSFM) Listed installations, Smoke Verify must be set to off.
To turn Smoke Verify off or on:
1.
2.
With the display showing ONBOARD OPTIONS, press ƒ
twice. The display shows SMOKE VERIFY OFF/ON (current
setting).
Press 1 (off) or 2 (on). The display flashes the entered
number. Press ƒ and the display shows the new setting.
Two Wire Smoke
(1101)
(Onboard Options—Inputs)
(Default = off) This setting determines how onboard hardwire
zone 8 is configured. When this setting is on, zone 8 will be
configured for two wire smoke detectors. When off, it will be
configured for a normal hardwire input.
To turn Smoke Verify off or on:
1.
2.
3.
With the display showing ONBOARD OPTIONS, press ƒ
twice. The display shows SMOKE VERIFY OFF/ON (current
setting).
Press A or B until the display shows TWO WIRE SMOKE ON/
OFF (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
number. Press ƒ and the display shows the new setting.
The following sections describe the settings that appear
under ONBOARD OPTIONS—OUTPUT PROGRAMMING.
OUTPUT N ITEM
7.
8.
OUTPUT 1_
GARAGE DOOR
Onboard Options Menu
The ONBOARD OPTIONS menu lets you set up the following built-in options:
INPUTS—This menu lets you turn the Smoke Verification
and the Two Wire Smoke features off or on.
42
Concord
Output Text
Output 1, 2 (Onboard Options Output Programming
Output 1: partition assign—11100, configuration—
11101
Output 2: partition assign—11110, configuration—
11111
(Defaults: Output 1 = Ptn 1, 01614; Output 2 = Ptn. 1, 01710)
This setting lets you assign the partition and the 5-digit
configuration number.
The configuration number determines
❑ which system event activates the selected output, and
❑ the duration or time the output is activated.
The first three digits represent the trigger number of an event
(such as triggering an alarm, opening a sensor, or arming the
system). The last two digits represent how the output
responds (such as momentary switching, maintained (or
latched) switching, or switching for a preset time).
Note
If you want to configure an output for user Output Control
you must use the Output Text feature to name the output.
If no Output Text is programmed, Output Control will not
function for that output.
(Onboard Options Output Text
—Output 1, 2)
(1120—output 1, 1121—output 2)
(Defaults = none) Use the following guidelines to “name”
onboard outputs:
❑ Use the item numbers listed in “Appendix B, Table B2”
for characters and words.
❑ If a desired word does not appear in Table B2, create it
using the characters (custom text).
❑ When using words from Table B2, spaces between them
appear automatically. When using characters from Table
B2 to create words, you must reserve an item number for
a ‘space’ after the word.
❑ Each character or word uses up one item number. For
example, a word from the list counts as one item number.
A created word (such as BOY’S) counts as six item numbers—4 letters, 1 apostrophe, and 1 space.
❑ Only 16 item numbers are allowed for each output name,
so plan ahead before programming output text. You may
need to abbreviate words to avoid running out of item
numbers.
Note
If you want to configure an output for user Output Control
you must use the Output Text feature to name the output.
If no Output Text is programmed, Output Control will not
function for that output.
Use the system event trigger and response numbers listed in
Appendix B: Reference Tables.
To set up onboard Output 1 & 2 partition and configuration
assignments:
1.
2.
3.
4.
5.
6.
7.
With the display showing ONBOARD OPTIONS, press ƒ +
B. The display shows OUTPUT PROGRAMMING.
Press ƒ and the display shows OUTPUT 1. Press B to
select OUTPUT 2.
Press ƒ and the display shows PARTITION ASSIGN n (current setting).
Press 1 or 2 to assign the output to the desired partition,
then press ƒ. The display shows PARTITION ASSIGN (new
setting).
Press B and the display shows CONFIGURATION TTTRR (current setting).
Enter the desired configuration number. The display
flashes the entered number. Press ƒ and the display
shows the new setting.
Press ƒ and repeat steps 2 through 6 until all outputs are
programmed.
To program Output Text:
1.
2.
3.
With the display showing ONBOARD OPTIONS, press ƒ then
press B twice and the display shows OUTPUT TEXT.
Press ƒ and the display shows OUTPUT 1.
Press ƒ and the display shows:
1 ITEM 0
0 - ________
where ITEM 0 is the first character or word location and 0
is the character or word number.
4. Enter the number of the desired character or word, or
scroll through the numbers by pressing B (forward) or A
(backward). If you make a mistake, simply enter the correct number or continue scrolling through choices.
5. Press ƒ to accept the displayed choice and the display
shows:
OUTPUT
1 ITEM 1
0 -________
6. Repeat steps 4 and 5 as needed to complete the output
name.
7. Press ‚ after entering the last character or word number.
The display shows the complete text name. For example:
OUTPUT 1
OUTPUT
GARAGE DOOR
Exiting Programming Mode
After all installer/dealer programming is completed, use the
following procedure to exit programming mode.
To exit programming mode:
Concord
1.
Press ‚ until the display shows SYSTEM
2.
Press A or B until the display shows EXIT
READY.
3.
Press ƒ and the touchpad displays the time and date.
PROGRAMMING.
PROGRAMMING
43
Entering User Programming Mode
The user programming mode lets you view system version
information and program the following system settings:
‰
‰
‰
‰
‰
‰
‰
‰
Time and Date
User Codes
Options
Set Up Schedules
Attach Schedules to Events
Energy Saver
Attach Lights to Sensors
System Version
User NN
(User Codes—Reg. User Codes
—User NN)
(030nn0 where nn=user number 00-59)
(Default = none) User codes perform basic arming and
disarming functions. The system allows up to 60 user codes
(user numbers 00–59). User numbers that show ✱✱✱✱ indicate
no code is currently programmed for that user number.
You can enter user programming from an alphanumeric or
fixed display touchpad by using the system or partition
master code.
The default system master code is 1234.
Press 9 + CODE. The display shows TIME
3.
4.
The panel uses a global clock and calendar for time and
date. Alphanumeric touchpads display the panel time and
date whenever the system is disarmed.
The TIME AND DATE menu lets you set this clock and calendar. The following procedures tell you how.
Note
Setting the time and date is important for accurate tracking
of system events stored in the event buffer.
(Time and Date)
(Default = 00:00) This setting lets you adjust the panel clock
to the correct time. The panel uses a 24-hour clock. For
example, to set the time to 4:17 P.M., enter 1617.
To set the Time:
2.
With the display showing TIME AND DATE, press ƒ and the
display shows TIME hh:mm (current time).
Enter the correct time (0000–2359). The display flashes
the entered time. Press ƒ and the display shows the new
time.
Date
(021)
(Time and Date)
(Default = 01/01/00) This setting lets you adjust the panel calendar to the correct month, day, and year.
To set the Date:
1.
2.
1.
AND DATE.
Time and Date Menu
1.
To program Regular User Codes:
2.
To enter user-programming mode:
Time
(020)
master code. You can enter up to 60 separate user codes,
allowing up to 60 different “users” access to the security
system. You can also specify whether or not a specific user
is able to perform specific actions like, bypass sensors or
test the system.
With the display showing TIME AND DATE, press ƒ, then A
or B until the display shows DATE nn/nn/nn (current date).
Enter the correct month (01–12), day (01–31), and year
(00–99). For example, enter 090100 for September 1,
2000. The display flashes the entered date. Press ƒ and
the display shows the new date.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER nn - nnnn.
With the desired user number displayed, enter a 4-digit
user code. The display flashes the entered code. Press ƒ
and the display shows USER nn - nnnn (new code).
To delete Regular User Codes:
1.
2.
3.
4.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn - nnnn (first
available user number).
Press A or B to select the desired user number/user code
you want to delete (if it is not already displayed), then
press ƒ. The display shows USER nn - nnnn.
Enter the system or partition master code. The display
flashes the entered code. Press ƒ and the display shows
USER nn -- ✱✱✱✱ (no code).
Direct Bypassing
(User Codes—Reg. User Codes
—User NN)
(030nn1 where nn=user number 00-59)
(Default = off) This setting determines whether or not a
specific user code provides access to the “bypass sensors”
feature. Set this feature to “on” for all users who need to be
able to bypass sensors.
To turn user code Direct Bypassing off or on:
1.
2.
3.
4.
5.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER nn - nnnn.
Press A or B until the display shows DIRECT BYPASSING
OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
User Codes Menu
The USER CODES menu lets you program/change regular
user access codes, partition master codes, and the system
44
Concord
Remote Access
(User Codes—Reg. User Codes
—User NN)
(030nn2 where nn=user number 00-59)
Latchkey Report
(Default = off) This setting determines whether or not the user
can access the panel from a remote phone (a phone located off
the premises).
(Defaults: 00–05 = on, 06–59 = off) This setting determines
whether or not the user code causes a latchkey report to be
sent to a pager when the code is used to change arming levels.
To turn user code Remote Access off or on:
To assign the Latchkey Report attribute to user codes:
1.
2.
3.
4.
5.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER nn - nnnn.
Press B until the display shows REMOTE ACCESS ON/OFF
(current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
(User Codes—Reg. User Codes
—User NN)
(030nn5 where nn=user number 00-59)
1.
2.
3.
4.
5.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER NN - NNNN.
Press A or B until the display shows LATCHKEY OFF/ON
(current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Partition Jump
(User Codes—Reg. User Codes
—User NN)
(030nn3 where nn=user number 00-59)
Partition Master
(User Codes—
Partition Master Code)
(partition 1: 0310, partition 2: 0311)
(Default = off) This setting determines whether or not a
specific user code can access one or both partitions. When
this is set to on, the user can access both partitions.
(Defaults = none) The Partition Master Code provides access
to all system operations and user programming for a single
partition.
Note
You must be “in” the partition of the partition master code
you wish to change.
To turn user code Partition Jump off or on:
1.
2.
3.
4.
5.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER nn - nnnn.
Press B until the display shows PARTITION JUMP OFF/ON
(current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
To change the Partition Master Code:
With the display showing USER CODES, press ƒ then A or
B until the display shows PARTITION MASTER CODE.
2. Press ƒ and the display shows PARTITION nnnn (current
code).
3. Enter a new 4-digit code. The display flashes the entered
code. Press ƒ and the display shows the new code.
1.
System Master
System Tests
(User Codes—Reg. User Codes
—User NN)
(030nn4 where nn=user number 00-59)
(Default = off) This setting determines whether or not a
specific user code provides access to the phone and sensor
tests. Set this feature to “on” for all users who need to be able
to conduct phone and sensor tests.
To turn user code System Tests off or on:
1.
2.
3.
4.
5.
With the display showing USER CODES, press ƒ and the
display shows REGULAR USER CODES.
Press ƒ and the display shows USER nn (first available
user number).
Press A or B to select the desired user number, then
press ƒ. The display shows USER nn - nnnn.
Press A or B until the display shows SYSTEM TESTS OFF/
ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
setting. Press ƒ and the display shows the new setting.
Concord
(User Codes—
System Master Code)
(0320)
(Default = 1234) The System Master Code provides access to
all system operations and user programming.
To change the System Master Code:
With the display showing USER CODES, press ƒ then A or
B until the display shows SYSTEM MASTER CODE.
2. Press ƒ and the display shows SYSTEM MASTER NNNN
(current code).
3. Enter a new 4-digit code. The display flashes the entered
code. Press ƒ and display shows the new code.
1.
Options Menu
The OPTIONS menu lets you set up the system for downloading and silent arming. You can also adjust alphanumeric
touchpad display brightness from this menu.
45
Volume
(043)
Downloading
(040)
(Options)
(Default = on) When this setting is on, the panel can
communicate with ITI ToolBox software for programming
the system from off-site.
Note
For this feature to work, the panel must be connected to a
phone line and be programmed with REMOTE ACCESS
on, with a Downloader phone number, and with a Downloader code.
1.
2.
3.
Press A or B until the display shows OPTIONS.
Press ƒ, then A or B until the display shows DOWNLOADING OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting.
Silent Arming
(041)
(Options)
(Default = off) This setting determines whether or not the
panel sounds status beeps from sirens and the touchpad when
the system is armed.
Note
When this feature is on, the user does not need to press 5
(SILENT) before arming the system to prevent status
sounds.
To turn Silent Arming off or on:
1.
2.
3.
Press A or B until the display shows OPTIONS.
Press ƒ, then A or B until the display shows SILENT ARMING OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting.
Touchpad Brightness
(042)
(Default = 4) This setting determines the volume level of
status sounds from speakers connected to the Phone Interface/
Voice Module.
Note
This menu appears only if a Phone Interface/Voice Module is connected to the panel.
To adjust status sound Volume:
1.
2.
To turn Downloading off or on:
(Options)
(Default = 2) This setting lets the user lighten or darken the
background on touchpad displays. Each touchpad can be set
to compensate for lighting conditions in the touchpad
location.
3.
3.
Press A or B until the display shows OPTIONS.
Press ƒ, then A or B until the display shows TOUCHPAD
BRIGHTNESS n (current setting).
Enter a setting from 0 (darkest background) to 3 (brightest background). The display flashes the entered selection. Press ƒ and the display shows the new setting.
Press A or B until the display shows OPTIONS, then press
ƒ.
Next, press A or B until the display shows VOLUME n
(current setting).
Enter a setting from 0 (off) to 7 (loudest). The display
flashes the entered selection. Press ƒ and the display
shows the new setting.
Voice Chime
(044)
(Options)
(Default = on) This setting determines whether speakers
connected to the Phone Interface/Voice Module announce
perimeter sensor/zone numbers that are tripped when the
Chime feature is on. For example, “Sensor one open.”
Note
This menu appears only if a Phone Interface/Voice Module is connected to the panel.
To turn Voice Chime off or on:
1.
2.
3.
Press A or B until the display shows OPTIONS.
Press ƒ then A or B until the display shows VOICE CHIME
OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting.
Chime On Close
(045)
(Options)
(Default = off) When this setting is on, the panel sounds a
single chime when a perimeter door or window is closed.
To turn Chime On Close off or on:
1.
2.
To adjust Touchpad Brightness:
1.
2.
(Options)
3.
Press A or B until the display shows OPTIONS.
Press ƒ then A or B until the display shows CHIME ON
CLOSE OFF/ON (current setting).
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting.
Set Up Schedules Menu
The SET UP SCHEDULES menu lets you set up time
frames for light control and exception opening/closing
reports. The system (all partitions) allows you to set up to
16 schedules (00–15).
Setting up schedules consists of setting a start and stop time
for each schedule, then selecting which days of the week the
schedule will be active. You can also set up a rollover
schedule, which starts on one day and ends on another day.
This saves programming time and leaves more schedules
available (in case they are needed later).
Rollover Schedule Example: To set up a schedule to rollover from Tuesday evening to Wednesday morning, set a
46
Concord
schedule start time for 2200 (10:00 P.M.) and a stop time for
0500 (5:00 A.M.). Set the schedule to turn on Tuesday.
Because the stop time is set for morning, the system automatically carries the schedule over to the next day.
If you use the same start and stop times described above and
set the schedule to turn on Monday through Friday, then one
schedule will cover the entire week.
Note
If you are programming schedules for your customer, be
sure to record the settings in the User’s Manual.
Set Up Schedules
05XXY where XX = schedule 00 thru 15 and Y = start (0)/
stop(1) 0 thru 8—Monday thru Sunday (2–8))
(Defaults = 00:00) This menu lets you set up start/stop times
for each day of the week.
To set up a Time Schedule:
1.
2.
3.
4.
5.
6.
7.
8.
9.
Press A or B until the display shows SET UP SCHEDULES.
Press ƒ and the display shows SCHEDULE 00. If you want a
different schedule number, press A or B until the desired
schedule number appears.
Press ƒ and the display shows START TIME hh:mm (current
setting).
Enter the desired starting time (00:00–23:59). The display flashes the entered time. Press ƒ and the display
shows START TIME hh:mm (new setting).
Press B and the display shows STOP TIME hh:mm (current
setting).
Enter the desired stop time (00:00–23:59). The display
flashes the entered time. Press ƒ and the display shows
STOP TIME hh:mm (new setting).
Press B and the display shows MONDAY OFF/ON (current
setting). To select a different day, continue pressing B
until the desired day appears.
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting
for the selected day.
Repeat steps 7 and 8 until all desired settings for each day
are set.
Latchkey Reports
Attach Schedules To Events
(060nn—Opening, 061nn—Closing where nn =
Schedule number [0 to 15])
(Defaults = off) This setting lets you attach the Latchkey
Opening report feature and the Latchkey Closing report
feature to time schedules.
To Attach a Schedule to Latchkey Opening or Latchkey
Closing:
1.
Press A or B until the display shows ATTACH
SCHEDULES
TO EVENTS.
2.
Press ƒ then A or B until the display shows LATCHKEY
or LATCHKEY CLOSING.
Press ƒ and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or
B until the desired schedule appears.
Press 1 (OFF) or 2 (ON). The display flashes the
entered selection. Press ƒ and the display shows the new
setting for the selected schedule.
OPENING
3.
4.
Exception Reports
Attach Schedules To Events
(062nn—Opening, 063nn—Closing, where nn =
Schedule number [0 to 15])
(Defaults = off) This setting lets you attach the Exception
Opening report feature and the Exception Closing report
feature to time schedules.
To Attach a Schedule to Exception Opening or Exception
Closing:
1.
Press A or B until the display shows ATTACH
SCHEDULES
TO EVENTS.
2.
Press ƒ then A or B until the display shows EXCEPTION
or EXCEPTION CLOSING.
Press ƒ and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or
B until the desired schedule appears.
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting
for the selected schedule.
OPENING
3.
4.
Attach Schedules to Events Menu
The ATTACH SCHEDULES TO EVENTS menu lets you
link the following system events to time schedules:
‰
‰
‰
‰
‰
‰
‰
Latchkey Opening—sends a report if system is disarmed
within the attached time schedule.
Latchkey Closing—sends a report if system is armed
within the attached time schedule.
Exception Opening—sends a report if system is not disarmed within the attached time schedule.
Exception Closing—sends a report if system is not armed
within the attached time schedule.
Lights (1–9) activate X-10 controlled lights by the
attached time schedule.
Outputs (1–6) allow users to attach onboard (1–2) and
SnapCard outputs to a schedule.
Arming—Allows the user to arm the panel at the schedule
start time.
Lights
Attach Schedules To Events
(064xnn where nn = Schedule number [0 to 15] and
x = light number [1 to 9] minus 1)
(Defaults = off) This setting lets you attach light controls to a
time schedule.
To Attach Schedules to Lights:
1.
2.
3.
4.
5.
6.
Concord
Press A or B until the display shows ATTACH
SCHEDULES
TO EVENTS.
Press ƒ then A or B until the display shows LIGHTS.
Press ƒ to enter the LIGHTS menu.
Press A or B until the desired light appears.
Press ƒ and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or
B until the desired schedule appears.
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting
for the selected schedule.
Repeat steps 3, 4, and 5 until all desired lights are
attached to schedules.
47
Outputs
Attach Schedules To Events
(065xnn where nn = Schedule number [0 to 15] and
x = output number [1 to 6] minus 1)
(Defaults = off) This setting lets you attach outputs to a time
schedule. Onboard outputs are 1–2, SnapCard outputs are 3–
6.
Note
Outputs can only be scheduled if text has been entered in
installer programming. Only onboard and SnapCard outputs can be scheduled.
To Attach Schedules to Outputs:
1.
Press A or B until the display shows ATTACH
SCHEDULES
Energy Saver Menu
The ENERGY SAVER menu lets you set the energy saver
module low- and high-setpoints. These setpoints determine
when the module relay closes, thereby completing the circuit through the thermostat to the furnace/air-conditioner.
Low Setpoint
(070)
(Default = 50°F) This setting determines the temperature at
which the energy saver module relay closes to activate the
furnace.
TO EVENTS.
2.
3.
4.
5.
6.
Press ƒ then A or B until the display shows OUTPUTS.
Press ƒ to enter the OUTPUTS menu.
Press A or B until the desired output appears.
Press ƒ and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or
B until the desired schedule appears.
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting
for the selected schedule.
Repeat steps 3, 4, and 5 until all desired outputs are
attached to schedules.
Arming
Attach Schedules To Events
(0660nn where nn = Schedule number [0 to 15])
(Defaults = off) This setting lets you arm according to a time
schedule.
Note
The low setpoint cannot be set equal to or higher than the
high setpoint.
To set the Low Setpoint:
1.
2.
Press A or B until the display shows ATTACH
2.
3.
4.
5.
6.
48
Press ƒ then A or B until the display shows ARMING.
To select arm to AWAY press ƒ.
Press ƒ and the display shows SCHEDULE 00 OFF/ON (current setting). If you want a different schedule, press A or
B until the desired schedule appears.
Press 1 (off) or 2 (on). The display flashes the entered
selection. Press ƒ and the display shows the new setting
for the selected schedule.
Repeat steps 4 and 5 until all desired schedules are
attached.
(Energy Saver)
(Default = 90°F) This setting determines the temperature at
which the energy saver module relay closes to activate the airconditioner.
Note
The high setpoint cannot be set equal to or lower than the
low setpoint.
SCHEDULES
TO EVENTS.
With the display showing ENERGY SAVER, press ƒ, then A
or B until the display shows LOW SETPOINT nn DEGREES
(current setting).
Enter the desired temperature (45–89°). The display
flashes the entered setting. Press ƒ and the display shows
the new setting.
High Setpoint
(071)
To Attach Schedules to Arming:
1.
(Energy Saver)
To set the High Setpoint:
1.
2.
With the display showing ENERGY SAVER, press ƒ, then A
or B until the display shows HIGH SETPOINT nn DEGREES
(current setting).
Enter the desired temperature (46–90°). The display
flashes the entered setting. Press ƒ and the display shows
the new setting.
Attach Lights to Sensors Menu
The ATTACH LIGHTS TO SENSORS menu lets you assign
a light number to a sensor. Each time the sensor is activated,
Concord
minute timer expires the light will turn off. If the same light
is scheduled, it will only turn on during the schedule time.
Light x to Sensor Y
(Attach Lights to Sensors)
(08n where n = light number [1–9] minus 1)
(Default = 0) This menu attaches light x to sensor y. Each
time a selected sensor is tripped, the selected light will turn on
and a 5 minute timer will start.
Note
The sensor must be learned into the current partition
before it can be attached.
3.
If the alphanumeric touchpad does not display SYSTEM
DOWNLOAD IN PROGRESS, call the downloader operator to verify the downloader phone number. Also, make sure ToolBox is set up properly. Refer to the “Troubleshooting”
section if the problem persists.
Testing the System
Note
Before testing, it is recommended that you have covers on
all modules (mounted outside the cabinet) and the panel
cabinet door closed. The testing environment should match
the system working environment.
To attach a light to a sensor:
1.
2.
3.
With the display showing LIGHT 1 TO SENSOR y (current
setting), press A or B to select the desired light number.
Enter the desired sensor number (01–76). The display
flashes the entered setting. Press ƒ and the display shows
the new setting.
Repeat steps 1 through 2 until all desired lights are
attached to sensors.
To detach a light from a sensor:
1.
2.
With the display showing LIGHT 1 TO SENSOR y (current
setting), press A or B to select the desired light number.
Enter 0 as the sensor number and press ƒ.
System Version Menu
The SYSTEM VERSION menu lets you view and identify
panel hardware and software. This information is primarily
used for troubleshooting purposes.
System Version
(010 = factory code, 011= system number,
012= system level)
(Default = N/A) This menu lets you view and identify panel
hardware and software version.
To view and identify the System Version:
1.
2.
3.
4.
Press A or B until the display shows SYSTEM VERSION.
Press ƒ and the display shows FACTORY CODE nnn✱nnnn.
Press B and the display shows SYSTEM NUMBER ✱nnnnnnn.
Press B again and the display shows SYSTEM LEVEL nnnn.
Press 8 + system master code + 7 + 0 (any), 1
(down), or 2 (up). The display shows SYSTEM DOWNLOAD IN PROGRESS during the downloading process.
This section describes the following:
‰
‰
‰
‰
‰
‰
‰
‰
‰
‰
Basic System Commands
Testing Zones/Sensors
Testing Phone Communication
Testing Central Station Communication
Testing Outputs and Sirens
Testing Light Control
Testing the Energy Saver Module
Changing Fixed Display Touchpads
Testing the Audio Verification Module
Testing Cellular Backup Communication
You should test the system after installing or servicing and
after adding or removing devices from the system.
Refer to the “Troubleshooting” section if correct test results
are not achieved.
Basic System Commands
Table 9 describes basic touchpad operating commands. For
complete details on system operation, including user programming, refer to the system User’s Manual.
Table 9: Basic Touchpad Commands
Command
System Response
✱ (STATUS)
Indicates current system status
✱+✱
Indicates AC power and battery
status
The panel can be programmed remotely using ToolBox.
Use the information you recorded in Appendix A to inform
the downloading operator of the programming requirements
for this system.
1 + CODE
Disarms system to OFF
2 + CODE
Arms system to STAY
3 + CODE
Arms system to AWAY
ToolBox Downloader Programming
2 (quick arm on)
Arms system to STAY
3 (quick arm on)
Arms system to AWAY
2 or 3 + CODE + 4
or
2 or 3 + 4
Arm system—No Delay (no exit or
entry delay)
5 + 2 or 3 + CODE
or
5 + 2 or 3
Arms system silently (no arming
status beeps)
7+1
Turns chime feature on and off
7+2
Turns Energy Saver on and off
Downloader Programming
Note
A Downloader Phone Number must be programmed and
the user-programmable option “Downloading” must be on
for remote downloader programming to work.
To initiate a ToolBox download session:
1.
Contact your download station and ask the operator to
prepare to download to the panel.
2.
Make sure the system is disarmed.
Concord
49
Table 9: Basic Touchpad Commands (Continued)
Command
System Response
7+6
Identifies alarms in memory
7+7+n
(n = output number
[1–6])
Turns the output on or off. (This
command is only functional after
output text is entered into panel
memory.)
1–2 = onboard outputs
3–6 = module outputs
8 + CODE + 6
Partition jump
8 + CODE + 2
Initiates a phone test
8 + CODE + 3
Initiates a sensor test
8 + installer CODE + 3 Initiates a dealer sensor test
Testing Zones/Sensors
Test sensors/zones after all programming is completed, whenever there is a change in environment, equipment, or programming, and whenever a zone- or sensor-related problem occurs.
If the system does not respond as described in the following
procedure, see the “Troubleshooting” section.
Note
While the sensor test is a valuable installation and service
tool, it only tests sensor operation for the current conditions. You should perform a sensor test after any change in
environment, equipment, or programming.
1.
Place all sensors and zones in their non-alarm state.
2.
At an alphanumeric touchpad, enter the sensor test
mode by pressing 8 + installer code + 3. The touchpad sounds one beep and displays SENSOR TEST. The
panel starts a 15 minute timer.
3.
Trip each zone/sensor one at a time. Touchpads (and
interior sirens) should sound one short, high-pitched
beep and the display should show the sensor name (or
number) and OK.
Note
If you hear a long, low-pitched beep, proceed to the following section “If a Wireless Sensor Does Not Test.”
4.
Press the STATUS button when you think all zones/sensors are tested. The touchpad displays any untested
sensors/zones and touchpad panics. If all sensors/zones
and touchpad panics have been tested, the display
shows SENSOR TEST OK.
this indicates that the wireless sensor signal strength is
below acceptable limits. Distance from the receiver, the
installation environment, or both, are most likely affecting
the sensor signal strength.
When possible, locate wireless sensors within 100 feet of
the panel. While a transmitter may have a range of 1,000
feet or more out in the open, the environment at the installation site can have a significant effect on transmitter range.
Refer to the “Troubleshooting” section to resolve the problem.
For wireless sensors that don’t respond, use an ITI RF
Sniffer (60-401) test tool to verify that the sensor is transmitting. Constant beeps from the RF Sniffer indicate a runaway (faulty) sensor. Remove the sensor battery(s) and
replace the sensor.
Testing Phone Communication
Perform a phone test to check the phone communication
between the panel and the central monitoring station.
To perform a phone test:
1.
Contact the central monitoring station to inform them
that you are testing the system.
2.
Press 8 + system master code + 2. The display reads
PHONE TEST and the touchpad sounds one beep. When
the panel completes the test, the system returns to the
previous arming level automatically.
If the display continues to show PHONE TEST for 1½ minutes
or more, enter 1 + system master code and refer to the
“Troubleshooting” section.
Testing Central Station/Pager
Communication
After performing sensor and phone tests, check that the system is reporting alarms successfully to the central station or
pager.
&$87,21
Be sure to contact the central monitoring station before
activating outputs that trigger from an alarm condition.
To test communication with the central station/pager:
1.
Call the central station and tell the operator that you
will be testing the system.
5.
Test any untested zones/sensors and touchpad panics.
2.
Arm the system.
6.
The system stays in sensor test mode for 15 minutes.
When less than 5 minutes remain, touchpads and interior sirens beep and the panel announces the remaining
time over the speakers once every minute. After 15
minutes the panel disarms to OFF, automatically. If
you need more time to complete the sensor test, press
8 + installer code + 3 while the system is still in sensor test mode. This restarts the 15 minutes of test time.
3.
Test each of the touchpad and wireless panic buttons
and trip at least one sensor of each type (fire, intrusion,
etc.) to verify correct operation.
4.
Check pager displays to verify reports are received.
7.
When all sensors/zones and touchpad panics have been
tested, press 1 + installer code to exit sensor test mode.
If a Wireless Sensor Does Not Test
If touchpads display SENSOR FAILURE and sirens sound a
long, low-pitched beep when a zone or sensor is tripped,
50
Pagers display an event code, digit sensor number, and
the last four digits of the account number. For example,
a pager display of
999 002 7468 indicates the following:
999 = alarm condition
002 = sensor/zone in alarm or user number
7468 = last four digits of account number
Concord
Note
The way information is displayed varies with pager services
and may not match the example above. Account numbers
with alpha-characters also vary when displayed, depending
on pager service. Account numbers are not displayed if
STREAMLINING is turned on.
Table 10 describes pager system event codes.
4.
Verify that each output responds according to the programmed configuration number. For outputs that trigger sirens, verify that the correct alarm sounds are
produced from these sirens. Table 12 describes the system alarm sounds you should hear for each alarm
event.
5.
Contact the central monitoring station when you are
finished testing.
Table 10: Pager System Event Codes
Code
System Event
Zone Restoral
111
System Disarmed
Fire
115
Sensor Test Exit
Police/Intrusion Continuous tone
118
Trouble condition cleared
Auxiliary
119
Alarm Canceled
222
System Armed to STAY
Testing Light Control
333
System Armed to AWAY
555
Phone/Sensor Test
Test all lights plugged into X-10 Lamp Modules to verify
house code and light number settings.
888
System Trouble Condition
To test light control:
999
System in Alarm
1.
Press 0 + 0 repeatedly to turn all lights on and off
together.
2.
Press 0 + 1 repeatedly to turn light 1 on and off.
3.
Repeat step 2 for remaining lights (0 + 2 for light 2,
0 + 3 for light 3, etc.).
4.
Arm the system to Away. All lights plugged into modules set to Unit 1 (or set as entry lights) should turn on
and stay on for 5 minutes. All lights plugged into modules set to Unit 2 should blink three times to indicate
the arming level. Remaining lights should not be
affected.
5.
Disarm the system. If Unit 1 (or entry) lights were on
for an entry or alarm, they will turn off in 5 minutes.
Unit 2 lights should blink once to indicate the system is
off. Remaining lights should not be affected.
6.
All lights should turn on and remain on during fire and
auxiliary/medical alarms. All lights should flash during
a police or intrusion alarm.
Table 11 describes pager sensor/zone number and user number report codes.
Table 11: Pager Sensor/Zone Code and Numbers
Code
000
5.
Table 12: System Alarm Sounds
009
Sensor/Zone or User Number
Alarm Type
System event not caused by a zone or user
001–076
Sensor/Zone Numbers 1–76
600–659
Regular User Codes 0–59 used
678
System Master Code used
679
Installer Code used
680
Dealer Code used
697
Quick Arm used
698
Keyswitch Sensor used
699
System Armed Itself (during service or powerup)
When you finish testing the system, call the central
monitoring station to verify that the alarms were
received.
&$87,21
Rapid beeps
Testing the Energy Saver Module (ESM)
Test the Energy Saver Module to verify it overrides the thermostat.
Testing Outputs and Sirens
All outputs (onboard and SnapCard) should be tested to verify configuration programming.
Alarm Sound
Repeating series of three beeps
Note
The system must have high- and low-temperature limits set
to test the Energy Saver Module.
To test the Energy Saver Module:
1.
Contact the central monitoring station to inform them
you are testing the system.
Press ‚ (status) + ‚ (status) to display the system status, ENERGY SAVER OFF, and the present TEMPERATURE
nn °. The temperature displayed (and/or announced)
should match the house thermostat. If the temperatures
do not match, refer to the ACCESSORY MODULES—
BUS DEVICES menu in the “Programming” section.
2.
2.
Verify that all wiring at the panel and output devices is
correct.
Press 7 + 2 to turn on the ESM. The display shows
ENERGY SAVER ON and the ESM relay will click once.
3.
3.
Activate the appropriate device to trigger each output
as programmed.
Press 7 + 2 again to turn the ESM off. The display
shows ENERGY SAVER OFF.
Be sure to contact the central monitoring station before
activating outputs that trigger from an alarm condition.
To test outputs:
1.
Concord
51
Note
There is a 5-minute delay after the Energy Saver Module
returns control to the furnace/AC before it will override the
furnace/AC again.
1.
The off-site helper calls the panel, lets the phone ring
twice, and hangs up.
2.
The helper must call the panel again in 10 to 40 seconds. The panel answers System hello.
Changing Fixed Display LCD Touchpad
Chime and Trouble Beep Tones
3.
The helper dials the following on the phone:
# 1234 # 8 (AVM access CODE) 5
The frequency (pitch) of chime and trouble beep tones from
a fixed display touchpad can be adjusted to a more desirable
or distinct tone, or to compensate for hearing impaired persons.
4.
The helper should now be able to hear you through the
AVM.
5.
Walk through the vicinity of the AVM while speaking
at a normal conversation level.
Note
Chime and trouble beep tones sound using the default frequency during, or within 15 seconds of, any button activity
at that specific touchpad.
6.
Tell the helper to dial a 1 and speak to you. To return to
listen mode, the helper dials a 3.
7.
When testing is complete, have the helper dial 99 and
hang up.
To change status tone pitch:
1.
Press and hold the ‚ and 0 buttons together until you
hear a steady tone, then release the buttons.
2.
Press and hold 1 to lower the pitch or press and hold
2 to raise the pitch.
3.
Release the button when the desired pitch is heard.
To test the module with the central station:
1.
Inform the central station that you will be sending an
alarm and testing an AVM.
2.
Give them the programming selections you made for
the panel (see “Audio Verification Menu” on page 38
for programming information).
After about 15 seconds of no touchpad activity, the steady
tone stops sounding.
3.
Use a touchpad panic button to initiate an auxiliary
alarm.
Adjusting Touchpad Display Contrast
4.
The central station operator waits for the alarm to be
reported and initiates an audio session.
5.
Walk through the vicinity of the AVM while speaking
at a normal conversation level.
6.
Have the operator speak to you.
7.
When testing is complete, the operator will end the session.
Touchpad displays can be adjusted for easier viewing to
help compensate for lighting conditions in the touchpad
location. The contrast adjustment lightens or darkens the
text.
To adjust display contrast:
Enter configuration mode by pressing the D and 6
buttons together for at least two seconds. The display
shows DA nnn.
Testing Cellular Backup Communication
2.
Press and release the 1 and 2 buttons together repeatedly, until the desired contrast level is displayed.
Perform this test to check the cellular communication
between the panel and the central monitoring station.
3.
Press ‚ and the display briefly shows DONE, then shows
the time and date.
To test Cellular Communication:
1.
Note
Vacuum fluorescent displays do not have a contrast adjustment.
Testing Audio Verification Module (AVM)
Communication
1.
Contact the central monitoring station to inform them
that you are testing the system.
2.
Install and activate the SuperBus 2000 Cellular Backup
Module.
3.
Verify or change the following CS PHONE 1 panel
option settings.
Note
If the current settings do not match the test settings, record
the current settings (Table 13), so that they can be restored
when this test is complete.
Test the Audio Verification Module from off-site and the
central station to verify that it works properly.
To test the module from off-site:
You will need a helper and touch-tone phone at an off-site
location to perform this test. When testing the AVM from
off-site the following guidelines must be followed.
4.
Disconnect the phone line by unplugging the Db-8 cord
from the RL-31X Jack.
5.
Initiate a phone test (8+system master code+2).
‰
6.
The phone test attempt should fail via the phone line
within 5 minutes. The panel will emit a long low tone
(and speak “phone failure 1” if so equipped).
7.
Wait for the phone test to succeed via the cell backup.
The panel should emit a short high tone (and speak
“phone test ok” if so equipped).
‰
‰
‰
52
The Remote Access feature must be set to on (default)
(page 27).
The Audio Verify feature must be set to on (page 38).
The system must be in a non-alarm state.
Optional Ring/Hang/Ring feature (page 27) must be on
(default) to work with steps 1 and 2 below. Otherwise wait
for 12 rings and the panel will pick up automatically.
Concord
8.
Verify the CS report.
If success does not occur, verify that the signal strength
(RSSI) shown on the Cellular Backup Module is
acceptable and repeat steps 5-8.
9.
Restore previous CS PHONE 1 settings if needed.
.
Table 13: Current Phone Settings
CS PHONE 1
Option
Test Setting
PHONE
NUMBER
Central station
phone number
HIGH LEVEL
RPTS
ON
BACKUP
OFF*
CELLULAR
BACKUP
ON
Previous
Setting
* Can be set to ON if no CS PHONE 2 PHONE NUMBER is
programmed.
Concord
53
54
Concord
Troubleshooting
This section describes what to do if you experience problems with system operation. If after performing the troubleshooting procedures the panel still malfunctions, please call
Technical Support at 1-800-777-2624.
Feature
Problem
Action/Solution
Panel Power
Panel does not power up. Touchpads don’t display or respond.
1. Verify that the panel transformer is plugged into an unswitched outlet.
2. Check the AC circuit breaker to be sure the circuit is live.
3. Check that the backup battery is installed correctly and the AC power transformer is plugged
in.
4. Check for proper panel and transformer wiring.
5. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 24 VAC.
No incoming AC voltage at panel terminals 1 and 2.
1. Unplug the AC power transformer and disconnect the wires from the transformer and the
panel.
2. Check transformer to panel wire for short or open circuits.
3. Plug in the transformer and check for 24 VAC at the transformer unconnected terminals. If
zero (0) volts, replace the transformer.
Touchpad display indicates System Low Battery or voice sounds “System low battery.”
1. Check that the backup battery is installed correctly and the AC power transformer is plugged
in.
2. Measure the incoming AC voltage at panel terminals 1 and 2. It should read about 24 VAC.
3. Check for 11.75 to 13.5 VDC battery voltage between the backup
battery spade lugs. If the battery voltage is not within this range, replace the battery.
Note
When the panel is running a backup battery test, the reading at the connected battery can
range from 11.2 to 13.5 VDC. The panel automatically runs a backup battery test under the
following conditions: (1) on initial power-up, (2) during user sensor test, (3) once every
minute when backup battery has failed, (4) once every 24 hours at the programmed STIME
(UL 98 Options off) or once every 4 hours (UL 98 Options on).
Note
With the AC power transformer plugged in, the panel automatically charges the battery.
While the battery is charging for the first time it is normal for the system to indicate System
Low Battery. This can take a number of hours depending on the initial battery charge. Once
the battery reaches 12.5 VDC (full charge as measured while in battery test), the condition
clears. If the trouble condition persists after 24 hours, replace the backup battery.
After pressing STATUS the touchpads flash AC or display AC Power Failure/AC Failure. (Panel continues to
operate from backup battery).
1. Check the AC circuit breaker to be sure the circuit is live.
2. Check for proper panel and transformer wiring.
3. Check that the transformer is plugged into a nonswitched outlet and secured with the provided
screw.
4. Check that the transformer is supplying AC to the panel. (Transformer internal fuse may be
blown.
WARNING !
Be careful when securing the transformer to an outlet with a metal cover. Hold the
cover tightly in place. You could receive a serious shock if the metal outlet cover
drops down onto the prongs of the plug while you are securing the transformer and
cover to the outlet box.
Access Codes
Customer cannot remember access code(s).
1.
2.
3.
4.
Concord
Check your records to see if you have the customer’s access code(s) on file.
Verify the access code(s) using the Downloader.
Clear memory and reprogram the panel locally.
Clearing the memory will erase onboard hardwire zone factory programming.
55
Feature
Problem
Action/Solution
Access Codes (continued)
Installer cannot remember install code.
1. Check your records to see if you have the install code on file.
2. Verify the install code using the Downloader.
3. Use the Dealer Code to enter program mode and view the installer code.
Installer cannot remember dealer code.
Check your records to see if you have the dealer code on file.
Arming and Disarming
System protests and won’t arm.
1. If arming to level 2, make sure all monitored perimeter doors and windows are closed.
2. If arming to level 3, make sure all perimeter and interior sensors are closed.
3. Press STATUS for an indication of the problem.
System won’t disarm.
1. Disarming using incorrect code. Enter correct code.
2. Access code is not programmed or set up in user programming to disarm system.
3. Wireless touchpad is not learned into system or hardwire touchpad is not communicating to
panel. Check installer programming for learned wireless touchpads.
4. The installer code is being used to disarm the system. The system is designed not to disarm
using the installer code. Use a regular or system master code to disarm the system.
Bypassing
Touchpad indicates Invalid and/or “Invalid” is heard when you attempt to bypass a sensor.
1. Attempting to bypass a 24-hour sensor that cannot be bypassed (group 26 fire sensors).
2. Sensor is not active in the current arming level.
System cancels sensor bypass when you try to arm to level 2 or 3.
Sensor is being bypassed before arming to 2—STAY or 3—AWAY. Arm to the desired level
before bypassing a sensor.
Wireless Sensor and Touchpad Batteries
System indicates Sensor/Touchpad nn low battery.
Replace the indicated device battery. Test the sensor/touchpad after replacing the battery.
Note
If the sensor/touchpad is not tested after battery replacement, the system continues to show
a low battery condition, since that was the last signal it received from the device. Testing the
sensor/touchpad with new batteries allows the panel to receive a signal with good battery
information.
Central Station/Pager Reporting
Central station/pager is not receiving reports.
1.
2.
3.
4.
5.
6.
7.
8.
Check that the premises phone line is working.
Perform a phone test.
Check that the DB-8 cord is plugged into the RJ-31X/CA-38A jack.
Check that the DB-8 cord is wired correctly to the panel.
Check for correct phone line wiring between the TELCO block and RJ-31X/CA-38A jack.
Replace faulty RJ-31X/CA-38A jack.
Replace faulty DB-8 cord.
Verify that central station/pager phone number is programmed into the panel. Reprogram the
phone number and retest, if necessary.
9. Verify that the correct phone format (SIA or CID) is being used.
10. For pagers, extend the pager delay setting (see the PHONE OPTIONS—GLOBAL menu in the
“Programming” section.
Alphanumeric Touchpads
Display shows all ************.
Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct
wiring.
56
Concord
Feature
Problem
Action/Solution
Alphanumeric Touchpads (continued)
Display is blank.
1. Check that panel is powered up.
2. Check for touchpad power and/or bus miswiring, opens, or shorts.
3. Check touchpad brightness setting (see the user-programming OPTIONS menu in the “Programming” section).
Touchpad buttons don’t beep when pressed.
1. Check for touchpad power and/or bus miswiring, opens, or shorts.
2. Check that key beeps option is set to on (see the ACCESSORY MODULES—BUS DEVICES
menu in the “Programming” section).
Fixed Display Touchpads
Display is lit but does not respond to key presses.
Touchpad is not connected to panel bus terminals or is wired incorrectly. Check and correct wiring.
Display is blank.
1. Check that panel is powered up.
2. Check for touchpad power and/or bus miswiring, opens, or shorts.
3. Check touchpad brightness setting (see the user-programming OPTIONS menu in the “Programming” section).
Touchpad buttons don’t beep when pressed.
1. Check for touchpad power and/or bus miswiring, opens, or shorts.
2. Check that key beeps option is set to on (see the ACCESSORY MODULES—BUS DEVICES
menu in the “Programming” section).
Speakers
Speakers don’t sound alarms.
1. Check for correct wiring at speaker and panel terminals; correct where necessary.
2. Speaker output has shut down because panel detected terminal 7 or 8 is shorted to ground.
Disconnect panel AC and battery backup power. Locate short and correct. Apply panel AC
and backup battery power and retest.
3. Alarm is in partition 2 and speaker is connected to panel terminals 7 and 8, which activate
only for partition 1 alarms.
Sirens
Piezo sirens connected to SnapCard, or onboard (panel) outputs 1 and/or 2 don’t produce any alarm sounds.
1. Check for incorrect wiring between siren and panel; correct where necessary.
2. Output has not been configured (set up) to activate sirens. Enter program mode and configure
output (see ACCESSORY MODULES—BUS DEVICES—SNAP CARD, or ONBOARD
OPTIONS—OUTPUT 1, 2 in the “Programming” section).
Supervised Wireless Sirens
Sirens don’t produce any sounds and LED doesn’t respond.
1. Check to make sure siren is not plugged into an outlet controlled by a switch. Move siren to a
nonswitched outlet location and test.
2. Panel doesn’t have a Power Line Carrier (PLC) card installed. Install PLC card.
3. Panel is not powered by a power line carrier transformer. Replace existing transformer with a
power line carrier transformer.
4. Power transformer and sirens are not plugged into outlets on the same electrical phase. Relocate sirens at different outlets to determine working locations.
5. Siren is programmed with incorrect partition house code. Clear siren house code by pressing
and holding siren button for 20 seconds. Reprogram with correct partition house code and
retest. See “Installing Supervised Wireless Sirens” (60-736-95) on page 10 for more information.
6. Siren house code is not programmed into panel. Enter program mode and set SWS and partition house codes.
Concord
57
Feature
Problem
Action/Solution
Supervised Wireless Sirens (continued)
Siren only works part of the time and/or at odd, irregular intervals.
Check that siren and/or panel transformer is not plugged into an outlet shared with a major
appliance, television, or computer which may generate noise and degrade the line carrier signal.
Hardwire Zones
System doesn’t go into alarm when zone is tripped.
1. System is disarmed. Arm system and then trip the zone.
2. Zone is not learned into panel memory. Enter installer/dealer program mode—LEARN SENSORS, and learn zone into memory.
3. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the
partition in the EDIT SENSORS menu.
4. For HIM zones, check that the HIM LED is blinking to verify communication with the panel.
If LED is off, check wiring between HIM and panel.
Zone reports trouble condition.
1. Check that onboard HIM and SnapCard zone inputs have a 2k-ohm EOL resistor installed at
the last device on the loop in series for N/C loops, in parallel for N/O loops.
2. Check for zone wire fault—short circuit on N/C loops, open circuit on N/O loops.
3. Make sure all devices on zone are in non-alarm state, then enter disarm command to reset
zone.
Wireless Sensor Zones
System doesn’t respond (in sensor test or when armed) when sensor is tripped.
1.
2.
3.
4.
5.
Verify that receiver antennas are installed and connections are secure.
Check that the wireless sensor battery(s) are installed.
Check the sensor battery(s) for low voltage. Replace battery(s) if necessary.
Use an RF Sniffer (60-401) to verify that sensor is transmitting.
Sensor is not learned into panel memory. Enter installer/dealer program mode—LEARN
SENSORS, and learn sensor into memory.
6. Zone is learned into wrong partition. Delete zone and learn into correct partition or change the
partition in the EDIT SENSORS menu.
Sensor reports trouble condition.
1. Sensor tamper switch is tripped—sensor cover is off, not latched securely, or sensor is not
mounted securely. Secure sensor mounting and/or cover, then trip sensor to clear the condition.
2. Check the sensor battery for low voltage. Replace batteries, if necessary.
Touchpad indicates [sensor #] supervisory and/or Sensor [sensor #] supervisory is heard.
1. Use an RF Sniffer (60-401) to verify that sensor is transmitting. If sensor is not transmitting,
check battery for low or no voltage and replace.
2. Change mounting position of sensor (from horizontal to vertical or vice versa) and test sensor
several times for consistency.
3. Sensor signal is not reaching panel/receiver because sensor is too far away. Remove sensor
from mounted location and test from other locations. Mount sensor in area where signal can
reach panel/receiver.
Smoke sensor beeps once every 44 seconds.
Sensor batteries are getting low. Replace batteries.
58
Concord
Feature
Problem
Action/Solution
Wireless Touchpads
System doesn’t respond to commands entered from wireless touchpad.
1. Verify that receiver antennas are installed and connections are secure.
2. Check that touchpad battery(s) are properly installed.
3. Check the touchpad battery(s) for low voltage. Replace battery(s), if
necessary.
4. Use an RF Sniffer (60-401) to verify that touchpad is transmitting.
5. Touchpad is not learned into panel memory. Enter program mode and learn touchpad into
memory (see LEARN SENSORS).
6. Touchpad is learned into wrong partition. Delete touchpad and learn into correct partition or
change the partition in the EDIT SENSORS menu.
Touchpad reports trouble condition.
Check the touchpad battery(s) for low voltage. Replace battery(s), if necessary.
Phones
Loss of dial tone at on-site phones after wiring RJ-31X jack or connecting the DB-8 cord.
1. Wait 2 minutes and try again. The panel may be busy trying to report to the central station.
2. Disconnect the panel DB-8 cord from the RJ-31X jack. If the phone still doesn’t work, the
system is okay and the problem is in the wiring.
3. Check RJ-31X jack wiring and TELCO block wiring. Replace RJ-31X jack if necessary.
4. Check DB-8 cord connections at the panel and RJ-31X jack. Replace cord if necessary.
5. Perform a phone test after troubleshooting the phone line.
Constant dial tone, preventing dial-out on premises phones.
One or more polarity-sensitive phones exist on-site. Reverse the phone wires connected to the
brown and gray wire terminals on the RJ-31X jack.
Light Control
Light controlled by X-10 Lamp Module is not working.
1. Check that the lamp has a working bulb and that the lamp switch is on.
2. Check to make sure X-10 module is not plugged into an outlet controlled by a switch. Move
to a nonswitched outlet location and test.
3. Panel doesn’t have a Power Line Carrier (PLC) card installed. Install PLC card.
4. Panel is not powered by a power line carrier transformer. Replace existing transformer with a
power line carrier transformer.
5. Power transformer and X-10 modules are not plugged into outlets on the same electrical
phase. Relocate modules or transformer to different outlets to determine working locations.
6. Check that the HOUSE dial on the X-10 module matches the partition house code programmed into the panel.
7. X-10 module is located in wrong partition. Move module to correct partition and retest.
8. Partition house codes are not programmed into panel. Enter program mode and set partition
house codes.
Energy Saver Module
Module does not respond to system commands or appear to control furnace.
1. Check that the module is wired correctly to the panel terminals.
2. Verify the module LED is flashing continuously. If the LED is not flashing, remove power
and check wiring.
3. There is a 5-minute delay after the module returns control to the furnace/AC thermostat,
before the module overrides the thermostat again. Wait 5-minutes and try again.
Module temperature does not match actual room temperature.
The module room temperature setting has not been adjusted or was adjusted before the module
warmed or cooled to room temperature. To ensure accuracy, wait at least 15 minutes after
installing the module before adjusting the temperature. To adjust the module room temperature
setting, see TEMPERATURE under the ACCESSORY MODULES—BUS DEVICES—UNIT-ID—
ENERGY OPTIONS menu in the section “Programming the Panel.”
Concord
59
Feature
Problem
Action/Solution
Automation Module
Module is not controlling or communicating with the panel and panel indicates a “bus failure unit nn” where nn is
the Automation Module bus unit number.
1. Check that the module is wired correctly to the panel terminals.
2. Verify the module red LED is flashing continuously. If the LED is not flashing, remove power
and check wiring.
3. There is a 5-minute delay after the module returns control to the furnace/AC thermostat,
before the module overrides the thermostat again. Wait 5-minutes and try again.
Module is not controlling or communicating with the panel and panel indicates a “bus failure unit AMnn” where nn
is the Automation Module bus unit number.
1. Check that the RS-232 cable is firmly connected to the Automation Module and the Automation Device.
2. Verify the Automation Device is powered and turned on.
Module is not controlling or communicating with the panel and panel does not indicates a bus failure.
Verify the Automation Device is learned on the bus.
Cellular Backup Module
Cellular backup report does not occur.
1. Verify the Cellular Backup option is on for the CS phone number being tested.
2. Verify that the module is learned on the bus.
3. Check that the Cellular Backup Module has been activated as outlined in the device Installation Instructions.
The panel indicates “auxiliary phone trouble 1.”
1.
2.
3.
4.
Check the antenna connection.
Adjust the antenna positioning for maximum signal.
Verify Cellular System setting.
Check that the Cellular Backup Module has been activated as outlined in the device Installation Instructions.
The panel indicates “auxiliary phone trouble 2.”
1. Check the antenna connection.
2. Adjust the antenna positioning for maximum signal.
3. Verify Cellular System setting.
The panel indicates “auxiliary phone trouble 3.”
1. Check the antenna connection.
2. Adjust the antenna positioning for maximum signal.
The panel indicates “auxiliary phone trouble 4.”
Contact the cellular provider for details.
The panel indicates “auxiliary phone trouble 5.”
Contact the cellular provider for details.
The panel indicates “auxiliary phone trouble 6.”
Replace the module.
60
Concord
Preliminary 12/13/01
Appendix A: System Planning
Worksheets
Table A2: Hardwire Devices
Part No.
Customer Name _________________________________
Address _______________________________________
Description
(Max.)
13-068
Magnetic Contact
3/8” press fit
N/A
13-070
Magnetic Contact –
surface mount
N/A
N/A
System Sensor models
2100D, 2100TD,
2100S, 2100TS, 2400,
or 2400TH or ESL
series 429AT, 521B or
521BXT
10 mA
13-082
PIR Motion Detector
10 mA
Table A1: Wireless Devices
Part No.
mA
Qty.
Qty.
60-362
Door/Window Sensor
60-670
SAW Door/Window Sensor
60-741-95
Micro Recessed Door/Window
Sensor
Sirens
60-499
Slim Line Door/Window Sensor
60-736*
N/A
60-688
Micro Door/Window Sensor
Supervised Wireless
Siren
60-641
Long-Life Door/Window Sensor
60-483-01
Slim Line Hardwire
Interior Siren
120 mA
13-046
Hardwire Exterior
Siren
145 mA
60-461*
Shock Sensor
60-459*
Sound Sensor (ITI)
60-462*
Glass Guard Sensor
60-506
System Sensor Smoke Sensor
SuperBus 2000/Miscellaneous Components
60-746-01
2x16 LCD
Alphanumeric
Touchpad
90 mA
60-820
Fixed Display LCD
Touchpad
30 mA
60-803
2x20 LCD
Alphanumeric
Touchpad
120 mA
60-804
2x20 VFD
Alphanumeric
Touchpad
120 mA
60-777-01
Phone Interface/Voice
Module
600 mA
60-764-0195R
RF Receiver
30 mA
60-838-95R 2100ARFT Smoke Sensor
60-460
Rate-of-Rise Heat Sensor
60-589*
Manual Fire Pull Sensor
60-504*
Freeze Sensor
60-452
Pendant Panic Sensor
60-458
Single Button Panic Sensor
60-457
Dual Button Panic Sensor
60-578
Water-Resistant Panic Sensor
60-511-0195
DS924i PIR Motion Sensor
60-639-95R SAW Indoor PIR Motion Sensor
60-63995R-OD
SAW Outdoor PIR Motion Sensor
(Not for intrusion protection)
60-755
Power Line Carrier
Card
110 mA
60-703-95
Crystal Indoor PIR Motion Sensor
60-756
185 mA
60-834-95
FlexGard Sound Sensor
4 Input/2 Output
SnapCard
60-597
HiTech Handheld Wireless
Touchpad
60-757
8Z Hardwire Zone
Expander SnapCard
230 mA
60-607
2-Button Keychain Touchpad
60-758
4 Output SnapCard
130 mA
60-606
4-Button Keychain Touchpad
60-774
Hardwire Input Module
18 mA
60-659-95
SAW 4-Button Keychain Touchpad
60-770
Hardwire Output
Module
91 mA
60-620-01
Energy Saver Module
20 mA
60-677*
Interrogator 200 Audio
Verification Module
10 mA
60-850
Standard
Cellular Backup
Module
1600 mA
60-850-01
High Power
Concord
Sub
Total
Hardwire Sensors/Detectors
City _________________ County ___________ State ___
Zip __________ Phone (____) ___________
Description
1900 mA
61
Preliminary 12/13/01
Table A2: Hardwire Devices (Continued)
* These devices not listed, investigated, or verified by UL.
† Listed, but not tested for compatibility by UL.
Part No.
60-783-02
Description
Automation Module
Qty.
mA
(Max.)
Sub
Total
35 mA
Total power consumption:
mA
Total power consumption using 30 VA transformer
and 4.0 AH backup battery not to exceed:
1,000
mA
Total power consumption using 50 VA transformer
and 7.0 AH backup battery not to exceed:
2,000
mA
Table A3: Zone and Sensor Assignments
No.
RF Zone
Module
Bus ID
Number
Module
Input
Number
Group
Partition
Zone/Sensor Text
01
02
03
04
05
06
07
08
09
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
62
Concord
Preliminary 12/13/01
Table A3: Zone and Sensor Assignments (Continued)
No.
RF Zone
Module
Bus ID
Number
Module
Input
Number
Group
Partition
Zone/Sensor Text
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
Concord
63
Preliminary 12/13/01
Table A4: System Settings Index and Record
Setting (reference) default
Shortcut No.
Setting
Installer Programming—8 + Installer/Dealer CODE + 00
24 Hour Tamper (page 31) Off
06000
AC Failure (page 33) Off
06010
Access Timeout (page 39) 90 sec
0904
Account No. (page 20) 00000
0010, 0020
Activity Timeout (page 29) 24 hrs
0305
Alarm Verify (page 35) Off
06108, 06208
Audio Mode (page 38) 1
0901
Audio Verify (page 38) Off
0900
Auto Phone Test (page 25) Off
02001
Auto Stay Arming (page 21) On
0014, 0024
Auto Test Reset (page 25) On
02002
Auxiliary Panic (page 31) On
0511, 0521
AVM Access Code (page 39) None
0906
Back In Service (page 32) On
06002
Backup (page 23) CS Phone 1 On, CS Phone 2-3 Off
0105, 0115, 0125
Battery Restoral (page 32) Off
06005
Beep Delay (page 39) 2 sec
0905
Buffer Control (page 32) Off
06001
1_____________2_____________
1_____________2_____________
1_____________2_____________
1_____________2_____________
1_____________2_____________3___________
Buffer Full Report (page 32) Off
06006
Bypass Reports (page 32) Off
06003
Call Wait Cancel (page 26) None
02009
Cancel Message (page 26) On
02007
Cellular Backup (page 23) CS Phone 1 On, CS Phone
2-3 Off
0107, 0117, 0127
1_____________2_____________3___________
Closing Reports (page 35) Off
06101, 06201
1_____________2_____________
Comm. Failure (page 26) On
02003
CS Phone 1-3 (page 22) None
0100, 0110, 0120
Daylight Saving (page 29) On
0306
Dealer Code (page 20) None
0002
Delete Sensors (page 39) None
082
Dial Tone Detect (page 27) On
02010
Dialer Abort (page 26) On
02005
Cellular System (page 41) B
Dial Abort Delay (page 27) 30 sec
02006
Disable Trouble Beeps (page 36) Off
0701
Downloader Code (page 20) 12345
0000
Downloader Phone No. (page 25) None
0180
DTMF Dialing (page 26) On
02004
1_____________2_____________3___________
Duress Code (page 22) None
0017, 0027
1_____________2_____________
Duress (page 35) Off
06104, 06204
1_____________2_____________
Edit Sensors (page 39) None
083
Entry Delay (page 29) 32 sec
0310, 0320
64
1_____________2_____________
Concord
Preliminary 12/13/01
Table A4: System Settings Index and Record (Continued)
Setting (reference) default
Shortcut No.
Setting
Entry Lights (page 30) none
0400, 0410
1_____________2_____________
Exception Reports (phones) (page 22) Off
0103, 0113, 0123
1_____________2_____________3___________
Exception Reports (pagers) (page 24) Off
0133, 0143, 0153,
0163, 0173
1_____________2_____________3___________
4_____________5_____________
Exit Delay (page 29) 64 sec
0311, 0321
1_____________2_____________
Exit Extension (page 20) On
0013, 0023
1_____________2_____________
Extended Delay (page 29) 4 min
0312, 0322
1_____________2_____________
Fire Panic (page 31) On
0510, 0520
1_____________2_____________
Fire Shutdown (page 38) Off
0902
Force Armed (page 34) Off
06105, 06205
1_____________2_____________
Freeze Alarm (page 35) Off
06107, 06207
1_____________2_____________
Global Fire (page 36) Off
0704
High Level Reports (phones) (page 22) CS Phone 1 On, 0101, 0111, 0121
CS Phone 2-3 Off
1_____________2_____________3___________
High Level Reports (pagers) (page 23) On
0131, 0141, 0151,
0161, 0171
1_____________2_____________3___________
4_____________5_____________
House Code (page 30) 1B, 2C
0401, 0411
1_____________2____________
Immediate Beeps (page 35) Off
0700
Installer Code (page 20) 4321
0001
Keychain TP Arming (page 31) Off
0513, 0523
1_____________2_____________
Keyswitch Sensor (page 21) None
0015, 0025
1_____________2_____________
Keyswitch Style (page 21) Transition
0016, 0026
1_____________2_____________
Latchkey Format (page 35) Off
06106, 06206
1_____________2_____________
Latchkey Reports (pagers) (page 24) On
0135, 0145, 0155,
0165, 0175
1_____________2_____________3___________
4_____________5_____________
Latchkey Zones (page 31) None
0500
Learn Sensors (page 37) None
080
Line Fail Delay (page 27) None
0213
Local Phone Control (page 27) On
0210, 0220
Low CPU Battery (page 32) On
06004
Low Level Reports (phones) (page 22) CS Phone 1 On,
CS Phone 2-3 Off
0102, 0112, 0122
1_____________2_____________3___________
Low Level Reports (pagers) (page 24) Off
0132, 0142, 0152,
0162, 0172
1_____________2_____________3___________
4_____________5____________
Next Phone Test (page 29) 7 days
0303
No Activity (page 34) Off
06103, 06203
1_____________2_____________
1_____________2____________
Open/Close Reports (phones) (page 24) Off
0104, 0114, 0124
1_____________2_____________3___________
Open/Close Reports (pagers) (page 24) Off
0134, 0144, 0154,
0164, 0174
1_____________2_____________3___________
4_____________5_____________
Opening Reports (page 34) Off
06100, 06200
1_____________2_____________
Onboard Output 1 (page 43) 01614- any audible alarm
11101
Onboard Output 2 (page 43) 01710 - status & alarm
tones
11111
Output Trip Time (page 29) 4 sec
0304
Pager Delay (page 26) 15 sec
02008
Pager Partition Assignment (page 24) 1
0137, 0147, 0157,
0167, 0177
Concord
1_____________2_____________3___________
4_____________5_____________
65
Preliminary 12/13/01
Table A4: System Settings Index and Record (Continued)
Setting (reference) default
Pager Phone 1-5 (page 23) None
Shortcut No.
0130, 0140, 0150,
0160, 0170
Setting
1_____________2_____________3___________
4_____________5_____________
Phone Access Key (page 28) #
0216, 0226
1_____________2_____________
Phone Panic (page 28) Off
0215, 0225
1_____________2_____________
Phone Test (page 27) On
02000
Phone Test Freq. (page 28) 7 days
0302
Police Panic (page 31) On
0512, 0522
Program Report (page 33) Off
06015
Quick Arm (page 20) Off
0011, 0021
1_____________2_____________
Quick Exit (page 20) On
0012. 0022
1_____________2_____________
Receiver Failure (page 33) Off
06011
Recent Closings (page 34) On
06102, 06202
1_____________2_____________
Remote Access (page 27) On
0211, 0221
1_____________2_____________
1_____________2_____________
RF Low Battery Rpt (page 33) Weekly
06012
RF Supervisory Rpt (page 33) Weekly
06013
RF TX Timeout (page 28) 12 hrs
0301
Ring/Hang/Ring (page 27) On
0212, 0222
1_____________2_____________
Reporting Format (SIA/CID) (page 23) CID
0106, 0116, 0126
1_____________2_____________3___________
Sensor Text (page 37) None
081
Silent Talkback (page 39) Off
0903
Siren Timeout (page 30) 4 min
0313, 0323
Siren Verify (page 36) Off
0710
Sleep Time
0314, 0324
Smoke Verify (page 42) Off
1100
SnapCard Output 1 (page 41)
(01400 - keychain touchpad star button activation)
101001
SnapCard Output 2 (page 41)
(00410 - any audible alarm)
101011
SnapCard Output 3 (page 41)
(00903 - arming to STAY or AWAY)
101021
SnapCard Output 4 (page 41)
(01003 - arming to AWAY)
101031
Star Is No Delay (page 31) Off
0514, 0524
1_____________2_____________
Streamlining (page 24) On
0136, 0146, 0156,
0166, 0176
1_____________2_____________3___________
4_____________5_____________
Supervisory Time (page 28) 03:00
0300
Swinger Limit (page 33) 1
06014
SWS Code (page 36) 003
0703
System Tamper (page 35) Off
06109, 06209
1_____________2_____________
Toll Saver (page 28) On
0214, 0224
1_____________2_____________
TP Panic RPT FMT (page 33) Off
06009
Two Trip Error (page 32) Off
06008
Two Wire Smoke (page 42) Off
1101
UL 98 Options (page 36) Off
0702
Zone Restorals (page 32) Off
06007
66
1_____________2_____________
1_____________2_____________
Concord
Preliminary 12/13/01
Appendix B: Reference Tables
CS Report
√
√
√
√
√
1, 2, 3
√
√
1, 2, 3
√
√
1, 2, 3
Auxiliary Instant
√
1, 2, 3
24-hour portable auxiliary button. Siren
shutoff confirms CS report.
Auxiliary Instant
√
1, 2, 3
Special
Intrusion
Special belongings, such as gun cabinets and
wall safes.
Police
Instant
√
√
√
1, 2, 3
09
Special
Intrusion
Special belongings, such as gun cabinets and
wall safes.
Police
Standard
√
√
√
1, 2, 3
10
Entry/Exit
Delay
Entry and exit doors that require a standard
delay time.
Police
Standard
√
√
√
√
2, 3
11
Entry/Exit
Delay
Garage doors and entrances that require an
extended delay time. *
Police
Extended
√
√
√
√
2, 3
12
Entry/Exit
Delay
Driveway gates and entrances that require a
twice extended delay time. *
Police
Twice
Extended
√
√
√
√
2, 3
13
Instant
Perimeter
Exterior doors and windows.
Police
Instant
√
√
√
√
2, 3
14
Instant Interior
Interior doors.
Police
Follower
√
Instant Interior
Interior PIR motion sensors. *
Police
Follower
16
Instant Interior
Interior doors.
Police
Follower
17
Instant Interior
PIR motion sensors. *
Police
Follower
18
Instant Interior
PIR motion sensors subject to false alarms. * † Police
Follower
√
√
√
√
√
2, 3
15
√
√
√
√
√
19
Delayed Interior Interior doors that initiate a delay before going Police
into alarm. *
Standard
√
√
3
20
Delayed Interior PIR motion sensors that initiate a delay before Police
going into alarm. *
Standard
√
√
3
21
Local Instant
Interior
24-hour local alarm zone protecting anything
that opens and closes.
Police
Instant
√
√
1, 2, 3
22
Local Delayed
Interior
Same as group 21, plus activation initiates a
delay before going into alarm.
Police
Standard
√
√
1, 2, 3
23
Local Instant
Auxiliary
24-hour local alarm zone protecting anything
that opens and closes. ‡
Auxiliary Instant
√
√
1, 2, 3
24
Local Instant
Auxiliary
24-hour local alarm zone protecting anything
that opens and closes. Sirens shut off at
restoral. *
Auxiliary Instant
√
√
No.
Name
Application
Alarm
Delay
00
Fixed Panic
24-hour audible fixed emergency buttons.
Police
Instant
01
Portable Panic
24-hour audible portable emergency buttons.
Police
Instant
02
Fixed Panic
24-hour silent fixed emergency buttons.
Silent
Instant
03
Portable Panic
24-hour silent portable emergency buttons.
Silent
Instant
04
Fixed Auxiliary 24-hour auxiliary sensor, such as Pendant
Panic or holdup button.
Auxiliary Instant
05
Fixed Auxiliary 24-hour auxiliary emergency button. Siren
shutoff confirms CS report.
Auxiliary Instant
06
Portable
Auxiliary
24-hour portable auxiliary alert button.
07
Portable
Auxiliary
08
Concord
Restoral
Supervisory
Chime (Level 1 only)
Table B1: Sensor Group Characteristics
√
√
√
Active
Levels
1, 2, 3
1, 2, 3
1, 2, 3
2, 3
3
3
3
1, 2, 3
67
Preliminary 12/13/01
Alarm
Delay
Chime (Level 1 only)
Application
CS Report
Name
Supervisory
No.
Restoral
Table B1: Sensor Group Characteristics (Continued)
Active
Levels
25
Local Special
Chime
Notify the user when a door is opened. Sounds Special
emit from a local annunciator. *
Chime
Instant
26
Fire
24-hour fire, rate-of-rise heat, and smoke
sensors.
Instant
√
√
27
Output Module Hardwire Output Module (HOM) lamp control Silent
or other customer feature. ‡
Instant
√
√
1, 2, 3
28
Output Module HOM, PIR motion sensor, sound sensor, or
pressure mat. ‡
Silent
Instant
√
1, 2, 3
29
Auxiliary
Auxiliary Instant
32
Output Module HOM, PIR motion sensor, sound sensor, or
pressure mat.‡
Silent
Instant
33
Siren
Wireless Siren Supervision. ‡
Silent
Instant
34
Gas
Carbonmonoxide (CO) Gas Detectors ‡
Auxiliary Instant
35
Local Instant
Police (Day
Zone)
Local alarm in levels 1 and 2. Report to CS in Police
level 3.
Freeze sensor.
Fire
Instant
1, 2, 3
√
√
1, 2, 3
√
√
√
1, 2, 3
√
√
1, 2, 3
√
√
√
√
√
√
1, 2, 3
1, 2, 3
(level 3
only)
Note: Check marks (√) represent characteristics present in a group.
* This group is not certified as a primary protection circuit for UL-listed systems and is for supplementary use only.
† Sounds instant police siren if two or more sensors are tripped within 4 minutes. Otherwise sensors are followers to delayed
sensors. If Alarm Verification is on, group 18 functions like group 17.
‡ This group has not been investigated by UL.
§ This group is required for UL-listed residential fire alarm applications.
68
Concord
Preliminary 12/13/01
Table B2: Item Numbers and Sensor Text
Item
Number
Sensor Text
Item
Number
Sensor Text
Item
Number
Sensor Text
Item
Number
Sensor Text
001
Aborted
040
Control
079
Gallery
118
Mother’s
002
AC
041
Date
080
Garage
119
Motion
003
Access
042
Daughter’s
081
Gas
120
No
004
Active
043
Degrees
082
Glass
121
North
005
Activity
044
Delay
083
Goodbye
122
Not
006
Alarm
045
Den
084
Hallway
123
Now
007
All
046
Desk
085
Heat
124
Number
008
AM
047
Detector
086
Hello
125
Off
009
Area
048
Dining
087
Help
126
Office
010
Arm
049
Disarmed
088
High
127
OK
011
Armed
050
Door
089
Home
128
On
012
Arming
051
Down
090
House
129
Open
013
Attic
052
Download
091
In
130
Opening
014
Auxiliary
053
Downstairs
092
Install
131
Panic
015
Away
054
Drawer
093
Interior
132
Partition
016
Baby
055
Driveway
094
Intrusion
133
Patio
017
Back
056
Duct
095
Invalid
134
Pet
018
Bar
057
Duress
096
Is
135
Phone
019
Basement
058
East
097
Key
136
Please
020
Bathroom
059
Energy Saver
098
Kids
137
PM
021
Battery
060
Enter
099
Kitchen
138
Police
022
Bedroom
061
Entry
100
Latchkey
139
Pool
023
Bottom
062
Error
101
Laundry
140
Porch
024
Breezeway
063
Exit
102
Left
141
Power
025
Building
064
Exterior
103
Level
142
Press
026
Bus
065
Factory
104
Library
143
Program
027
Bypass
066
Failure
105
Light
144
Progress
028
Bypassed
067
Family
106
Lights
145
Quiet
029
Cabinet
068
Father’s
107
Living
146
Rear
030
Canceled
069
Feature
108
Load
147
Receiver
031
Car
070
Fence
109
Loading
148
Report
032
Carbon
Monoxide
071
Fire
110
Low
149
RF
033
Central
072
First
111
Lower
150
Right
034
Chime
073
Floor
112
Main
151
Room
035
Closed
074
Force
113
Master
152
Safe
036
Closet
075
Foyer
114
Mat
153
Schedule
037
Closing
076
Freeze
115
Medical
154
Screen
038
Code
077
Front
116
Memory
155
Second
039
Computer
078
Furnace
117
Menu
156
Sensor
Concord
69
Preliminary 12/13/01
Table B2: Item Numbers and Sensor Text (Continued)
Number
Text
Number
Text
Number
Text
Number
Text
156
Sensor
175
Time
194
9
212
R
157
Service
176
To
195
A
213
S
158
Shed
177
Touchpad
196
B
214
T
159
Shock
178
Trouble
197
C
215
U
160
Side
179
Unbypass
198
D
216
V
161
Siren
180
Unit
199
E
217
W
162
Sliding
181
Up
200
F
218
X
163
Smoke
182
West
201
G
219
Y
164
Son’s
183
Window
202
H
220
Z
165
Sound
184
Zone
203
I
221
(space)
166
South
185
0
204
J
222
’(apostrophe)
167
Special
186
1
205
K
223
- (dash)
168
Stairs
187
2
206
L
224
_ (underscore)
169
Stay
188
3
207
M
225
*
170
Supervisory
189
4
208
N
226
#
171
System
190
5
209
O
227
:
172
Tamper
191
6
210
P
228
/
173
Temperature
192
7
211
Q
229
?
174
Test
193
8
Table B3: System Event Trigger Numbers
System Event
Description
Trigger
No.
Null Trigger (used for direct control)
Activated only by schedule or direct command.
000
Fire Alarm
When Fire sirens are started.
001
Police Alarm
When Police sirens are started.
002
Auxiliary Alarm
When Auxiliary sirens are started.
003
Any Audible Alarm
When any of the above sirens are started.
004
Silent Alarm (sensor groups 2, 3, and duress)
When a sensor in group 2 or 3 goes into alarm or when a duress
alarm is activated (does not include groups 25, 27, 28, or 32).
005
Any Audible or Silent Alarm
When any alarm is started (does not include groups 25, 27, 28, or 006
32).
HOM Group 27, 28, 32 in Alarm
When a sensor in group 27, 28, or 32 goes into alarm.
007
Major Trouble (phone or receiver failure)
When a receiver failure (S94) or a phone failure (S96) occurs.
008
Arming to STAY or AWAY
When the panel is armed to level 2 or 3.
009
Arming to AWAY
When the panel is armed to level 3.
010
AVM is Interactive (audio session in progress)
When the central station operator begins listening or talking to
the premises.
011
Fail-to-Communicate (panel can’t call CS or pager) When the fail-to-communicate output is activated.
012
AVM Trip (edge)
When an AVM alarm occurs, output is activated momentarily.
013
Keychain Touchpad Star Button-Press
When the star button on a keychain touchpad is pressed.
014
70
Concord
Preliminary 12/13/01
Table B3: System Event Trigger Numbers (Continued)
System Event
Trigger
No.
Description
Smoke Power (for resetting 4-wire smoke
detectors)
Deactivated when hardwire smoke detectors need to be reset.
015
Exterior Siren
Activated for police or fire alarms.
016
Interior Siren
Activation follows all system noises
017
AVM Trip (pulse)
When an AVM alarm occurs, output is deactivated for 10 ms
018
State of System Status
Follows the state of system status (ready or trouble).
019
Tamper Condition
When any tamper is tripped
020
Closing Report Sent
When a closing report has been successfully transmitted to the
central station.
021
Group XX in Alarm
When any sensor in group XX goes into alarm
see
Table B4
Sensor XX in Alarm
When sensor number XX goes into alarm
see
Table B4
Sensor XX Open
When sensor number XX is opened
see
Table B4
Table B4: Sensor Group Event Trigger Numbers
Sensor Group
Concord
Trigger No.
Table B4: Sensor Group Event Trigger Numbers
Sensor Group
Trigger No.
Group 00 in alarm
064
Group 17 in alarm
081
Group 01 in alarm
065
Group 18 in alarm
082
Group 02 in alarm
066
Group 19 in alarm
083
Group 03 in alarm
067
Group 20 in alarm
084
Group 04 in alarm
068
Group 21 in alarm
085
Group 05 in alarm
069
Group 22 in alarm
086
Group 06 in alarm
070
Group 23 in alarm
087
Group 07 in alarm
071
Group 24 in alarm
088
Group 08 in alarm
072
Group 25 in alarm
089
Group 09 in alarm
073
Group 26 in alarm
090
Group 10 in alarm
074
Group 27 in alarm
091
Group 11 in alarm
075
Group 28 in alarm
092
Group 12 in alarm
076
Group 29 in alarm
093
Group 13 in alarm
077
Group 32 in alarm
096
Group 14 in alarm
078
Group 33 in alarm
097
Group 15 in alarm
079
Group 34 in alarm
098
Group 16 in alarm
080
Group 35 in alarm
099
71
Preliminary 12/13/01
Table B5: Sensor Number Event Trigger Numbers
Sensor
Number
State
Trigger
No.
State
Trigger
No.
Table B5: Sensor Number Event Trigger Numbers
Sensor
Number
State
Trigger
No.
State
Trigger
No.
Sensor 01
in alarm
129
open
257
Sensor 39
in alarm
167
open
295
Sensor 02
in alarm
130
open
258
Sensor 40
in alarm
168
open
296
Sensor 03
in alarm
131
open
259
Sensor 41
in alarm
169
open
297
Sensor 04
in alarm
132
open
260
Sensor 42
in alarm
170
open
298
Sensor 05
in alarm
133
open
261
Sensor 43
in alarm
171
open
299
Sensor 06
in alarm
134
open
262
Sensor 44
in alarm
172
open
300
Sensor 07
in alarm
135
open
263
Sensor 45
in alarm
173
open
301
Sensor 08
in alarm
136
open
264
Sensor 46
in alarm
174
open
302
Sensor 09
in alarm
137
open
265
Sensor 47
in alarm
175
open
303
Sensor 10
in alarm
138
open
266
Sensor 48
in alarm
176
open
304
Sensor 11
in alarm
139
open
267
Sensor 49
in alarm
177
open
305
Sensor 12
in alarm
140
open
268
Sensor 50
in alarm
178
open
306
Sensor 13
in alarm
141
open
269
Sensor 51
in alarm
179
open
307
Sensor 14
in alarm
142
open
270
Sensor 52
in alarm
180
open
308
Sensor 15
in alarm
143
open
271
Sensor 53
in alarm
181
open
309
Sensor 16
in alarm
144
open
272
Sensor 54
in alarm
182
open
310
Sensor 17
in alarm
145
open
273
Sensor 55
in alarm
183
open
311
Sensor 18
in alarm
146
open
274
Sensor 56
in alarm
184
open
312
Sensor 19
in alarm
147
open
275
Sensor 57
in alarm
185
open
313
Sensor 20
in alarm
148
open
276
Sensor 58
in alarm
186
open
314
Sensor 21
in alarm
149
open
277
Sensor 59
in alarm
187
open
315
Sensor 22
in alarm
150
open
278
Sensor 60
in alarm
188
open
316
Sensor 23
in alarm
151
open
279
Sensor 61
in alarm
189
open
317
Sensor 24
in alarm
152
open
280
Sensor 62
in alarm
190
open
318
Sensor 25
in alarm
153
open
281
Sensor 63
in alarm
191
open
319
Sensor 26
in alarm
154
open
282
Sensor 64
in alarm
192
open
320
Sensor 27
in alarm
155
open
283
Sensor 65
in alarm
193
open
321
Sensor 28
in alarm
156
open
284
Sensor 66
in alarm
194
open
322
Sensor 29
in alarm
157
open
285
Sensor 67
in alarm
195
open
323
Sensor 30
in alarm
158
open
286
Sensor 68
in alarm
196
open
324
Sensor 31
in alarm
159
open
287
Sensor 69
in alarm
197
open
325
Sensor 32
in alarm
160
open
288
Sensor 70
in alarm
198
open
326
Sensor 33
in alarm
161
open
289
Sensor 71
in alarm
199
open
327
Sensor 34
in alarm
162
open
290
Sensor 72
in alarm
200
open
328
Sensor 35
in alarm
163
open
291
Sensor 73
in alarm
201
open
329
Sensor 36
in alarm
164
open
292
Sensor 74
in alarm
202
open
330
Sensor 37
in alarm
165
open
293
Sensor 75
in alarm
203
open
331
Sensor 38
in alarm
166
open
294
Sensor 76
in alarm
204
open
332
72
Concord
Preliminary 12/13/01
Table B7: Response Characteristics (Continued)
Response
Characteristics
Table B6: System Feature Event Trigger Numbers
Feature
State
Trigger
No.
Phone Test
initiated
225
AC Failure
for 15 minutes
226
CPU Low Battery
detected (excluding first
minute after power-up)
227
Siren pattern
The point will activate and deactivate
according to the current alarm type:
Auxiliary -- fast on/off/on
Police -- constant on
Fire -- repeating)
Trip delay
Auto Phone Test
begun
228
Receiver Failure
detected
229
Back In Service
alarm (AC loss, battery
drain, then AC restore)
230
Phone Failure
detected
231
Buffer Full
detected
232
Description
The point will activate 30 seconds after
the trigger event occurs
Table B8: Response Numbers
Siren
Trip Delay
Tracking
no
no
Response
Time
momentary
Response
No.
00
5
01
233
no
no
3 minutes
alarm (40 incorrect code
entry keystrokes)
236
no
no
siren time2
02
no
no
sustained3
03
Freeze
alarm
237
no
yes4
momentary
04
No Activity
alarm
238
no
yes4
3 minutes5
05
no
4
2
siren time
06
4
3
Two Trip Error
System Tamper
Fire Panic
Police Panic
Auxiliary Panic
Opening Report
Closing Report
detected
alarm
239
alarm
alarm
occurred
240
no
yes
sustained
07
241
yes1
no
momentary
08
242
yes1
no
3
minutes5
09
yes1
no
siren time2
10
occurred
243
Latchkey Opening or occurred
Closing
244
Duress
alarm
Force Armed Report
245
occurred
yes
yes
1
yes
1
Recent Closing
Report
occurred
248
Sensor Test
entered
249
sustained
11
momentary
12
yes4
3 minutes5
13
1
4
yes
2
siren time
14
yes4
sustained3
15
yes1
247
4
yes
yes
alarm
no
yes1
246
Fire in Partition
3
Notes for Table B.8 Response Numbers
1.
If an event does not trigger sirens, siren tracking
response numbers activate without turning on the output. If sirens are triggered by another event, the output
pulses to match the siren.
Table B7: Response Characteristics
Response
Characteristics
If the siren cadence changes (from police to fire, for
example), outputs set up for siren tracking change to
match the siren and all pulsing outputs pulse to one
common cadence.
Description
Momentary trip time The point will remain activated for nn
seconds (n is 1-12 seconds). The
default is 4 seconds
3 minute trip time
The point will remain activated for 3
minutes
Siren-time trip time
The point will remain activated while
the interior siren is sounding
Sustained trip time
The point will remain activated for the
duration of the event
Concord
Note
The mechanical lifetime of the relay may be exceeded if
an output is set up for a siren tracking response and a
pulsing siren (auxiliary or fire) is active for long time periods. A SnapCard relay output’s lifetime expectancy is
about 350 total pulsing hours.
2.
If an event does not trigger sirens, siren time response
times activate outputs only if sirens are active for
another reason.
3.
If an alarm event does not necessarily require disarming (no activity, closing report, etc.), outputs set up for
a sustained response time remain activated until the
next arming level change.
73
Preliminary 12/13/01
4.
If an event occurs that activates an output set up for trip
delay, the delay and output activation can be canceled
by trigger event restoral.
Note
The trip delay is factory set for 30 seconds and cannot be
changed.
74
5.
Activated outputs set up for a 3-minute response time
remain active for the entire three minutes. To deactivate
the output before the 3-minute time expires, you must
enter program mode or remove panel power.
Activated outputs set up for a momentary or 3-minute
response time restart if the same trigger event occurs
again.
Concord
Appendix C: Settings
T o e n te r P ro g ra m m in g M o d e ,
8 + In s ta lle r o r
D e a le r C o d e + 0 + 0
#
S y s te m P ro g ra m m in g
B
A
D e m o K it
O n O ff
P a rtitio n 1
C o p y
C le a r
M e m o ry
E x it
P ro g ra m m in g
#
S e c u rity
*
*
#
B
G lo b a l
*
#
A
A
0 0 0 2
* * * *
B
B
A
A
E x it E x te n s io n
O n O ff
0 0 1 3
B
A
0 0 1 4
0 0 1 4
A
B
te s
U n d e rlin e d s e ttin g s in d ic a te d e fa u lts .
S h o rtc u t n u m b e rs a p p e a r in th e lo w e r-le ft
o f e a c h m e n u b o x , w h e re a p p lic a b le .
B
K e y s w itc h S ty le
T ra n s itio n S ta te
0 0 1 6
B
B
A
0 0 1 7
* * * *
A
D u re s s C o d e
0 0 1 7
* * * *
B
A
L o w L e v R p ts
O n O ff
0 1 2 2
B
A
B
E x c e p tio n R p ts
O n O ff
0 1 1 3
A
A
E x c e p tio n R p ts
O n O ff
0 1 2 3
B
A
B
A
O p e n /C lo s e
R p ts O n O ff
O p e n /C lo s e
R p ts O n O ff
O p e n /C lo s e
R p ts O n O ff
0 1 1 4
A
0 1 2 4
B
B a c k u p
O n O ff
A
0 1 1 5
B
K e y s w itc h S ty le
T ra n s itio n S ta te
0 0 1 6
D u re s s C o d e
A
0 1 0 5
A
A
L o w L e v R p ts
O n O ff
0 1 1 2
B
A
H ig h L e v R p ts
O n O ff
0 1 2 1
B
B
0 0 1 5
A
B
H ig h L e v R p ts
O n O ff
0 1 1 1
0 1 0 4
A
A
A
K e y s w itc h
S e n s o r
0 0 1 5
B
B
A u to S ta y A rm in g
O n O ff
K e y s w itc h
S e n s o r
N o
1 .
2 .
c o rn e r
0 1 2 0
A
A
A u to S ta y A rm in g
O n O ff
B
0 1 1 0
B
E x c e p tio n R p ts
O n O ff
0 1 0 3
B
B
0 1 0 0
A
E x it E x te n s io n
O n O ff
0 0 1 3
*
#
P h o n e N u m b e r
L o w L e v R p ts
O n O ff
0 1 0 2
B
*
P h o n e N u m b e r
B
0 0 1 2
B
C S P h o n e 3
A
#
H ig h L e v R p ts
O n O ff
0 1 0 1
Q u ic k E x it
O n O ff
0 0 1 2
B
C S P h o n e 2
P h o n e N u m b e r
A
Q u ic k E x it
O n O ff
D e a le r C o d e
A
Q u ic k A rm
O n O ff
0 0 2 1
Q u ic k A rm
O n O ff
0 0 1 1
In s ta lle r C o d e
4 3 2 1
0 0 0 1
*
#
B
A
B
A
A c c o u n t
N u m b e r 0 0 0 0 0
0 0 2 0
B
*
C S P h o n e 1
*
#
(C o n tin u e d )
#
P a rtitio n 2
A
A c c o u n t
N u m b e r 0 0 0 0 0
0 0 1 0
B
B
B
*
#
D o w n lo a d e r
C o d e 1 2 3 4 5
0 0 0 0
*
P a rtitio n 1
A
P h o n e s
A
B
B a c k u p
O n O ff
A
0 1 2 5
B
A
B a c k u p
O n O ff
B
A
R e p o rtin g F o rm a t
S IA C ID
R e p o rtin g F o rm a t
S IA C ID
R e p o rtin g F o rm a t
S IA C ID
0 1 0 6
0 1 1 6
0 1 2 6
B
C e llu la r B a c k u p
O n O ff
0 1 0 7
A
B
C e llu la r B a c k u p
O n O ff
0 1 1 7
A
B
A
C e llu la r B a c k u p
O n O ff
0 1 2 7
8 6 9 0 G 0 4 B .D S F
Concord
75
TIER 2 MENUS (cont.)
B
Phones (cont.)
A
B
A
B
Pager
Phone 1
A
*
#
B
Pager
Phone 2
A
*
#
B
Pager
Phone 3
A
*
#
B
Pager
Phone 4
Pager
Phone 5
A
#
*
#
B
A
*
Downloader
Phone
#
*
Phone Number
Phone Number
Phone Number
Phone Number
Phone Number
Phone Number
0130
0140
0150
0160
0170
0180
B
A
B
A
B
A
B
A
B
A
High Lev Rpts
On Off
High Lev Rpts
On Off
High Lev Rpts
On Off
High Lev Rpts
On Off
High Lev Rpts
On Off
0131
B
0141
B
0151
B
0161
B
0171
B
A
Low Lev Rpts
On Off
0132
B
A
Low Lev Rpts
On Off
0142
A
B
A
Low Lev Rpts
On Off
0152
A
B
A
Low Lev Rpts
On Off
0162
A
B
A
Low Lev Rpts
On Off
0172
A
B
A
Exception Rpts
On Off
Exception Rpts
On Off
Exception Rpts
On Off
Exception Rpts
On Off
Exception Rpts
On Off
0133
B
0143
B
0153
B
0163
B
0173
B
A
Open/Close
Rpts On Off
0134
B
A
Open/Close
Rpts On Off
A
0144
B
A
Open/Close
Rpts On Off
A
0154
B
A
Open/Close
Rpts On Off
A
0164
B
A
Open/Close
Rpts On Off
A
0174
B
A
Latchkey Rpts
On Off
Latchkey Rpts
On Off
Latchkey Rpts
On Off
Latchkey Rpts
On Off
0135
0145
0155
0165
0175
A
Streamlining
On Off
0136
B
B
A
Streamlining
On Off
0146
A
B
B
A
Streamlining
On Off
0156
A
B
B
A
Streamlining
On Off
0166
A
B
B
A
Streamlining
On Off
0176
A
B
A
*
#
B
B
Global
A
Ptn Assignment
1 2
Ptn Assignment
1 2
Ptn Assignment
1 2
Ptn Assignment
1 2
Ptn Assignment
1 2
0137
0147
0157
0167
0177
Partition 2
Partition 1
A
A
*
#
Phone Test
On Off
02000
B
A
Auto Phone
Test On Off
02001
B
A
Auto Test Reset
On Off
02002
B
A
B
Local Phone
Ctrl
On Off
0220
B
A
Remote Access
On Off
0211
Remote Access
On Off
0221
B
A
B
A
Ring/Hang/
Ring
Ring/Hang/
Ring
On Off
On Off
0212
B
0222
B
A
B
A
Toll Saver
On Off
Toll Saver
On Off
0214
A
B
0224
A
Phone Panic
On Off
B
A
Phone Panic
On Off
0215
A
B
A
0225
B
A
Dial Abort Delay
30 secs (15-120)
Phone ACC Key
# ✱
Phone ACC Key
# ✱
02006
0216
0226
B
A
Cancel Message
On Off
02007
B
A
Pager Delay
15 secs (0-30)
02008
B
A
Call Wait Cancel
None
02009
B
A
Dial Tone Detect
On Off
02010
76
A
0213
A
Dialer Abort
On Off
02005
B
Local Phone
Ctrl
On Off
0210
B
A
Line Fail Delay
None (10-240)
Comm Failure
On Off
02003
B
*
#
*
#
DTMF Dialing
On Off
02004
Latchkey Rpts
On Off
B
B
Phone Options
8 6 9 0 G 0 5 A .D S F
Concord
*
#
*
#
S u p e rv s . T im e
R n d m 1 :0 0 -4 :0 0
0 3 0 0
B
B
B
B
R F T x T im e o u t
1 2 h o u rs (2 -2 4 )
0 3 0 1
A
E x it D e la y
6 4 s e c s (4 8 -1 8 4 )
0 3 1 1
A
A
E x te n d e d D e la y
4 m in s (1 -8 )
0 3 1 2
B
B
A
N e x t P h . T e s t
7 d a y s (1 -2 5 5 )
0 3 0 3
B
A
O u tp u t T rip T im e
4 s e c (1 -1 2 )
0 3 0 4
B
A
Q u ic k A rm
O n O ff
0 3 2 1
B
B
P h . T e s t F re q
7 d a y s (1 -2 5 5 )
0 3 0 2
#
A c c o u n t
N u m b e r 0 0 0 0 0
0 3 2 0
A c c o u n t
N u m b e r 0 0 0 0 0
0 3 1 0
A
*
#
B
S ire n T im e o u t
4 m in s (1 -3 0 )
0 3 2 3
B
B
S le e p T im e
B
H o u s e C o d e
1 B (1 -2 5 5 )
0 4 1 1
*
L a tc h k e y Z o n e s
N o n e (1 -7 6 )
0 5 0 0
*
#
A
A
S le e p T im e
2 2 :0 0 (0 0 :0 0 -2 3 :5 0 )
2 2 :0 0 (0 0 :0 0 -2 3 :5 0 )
0 3 1 4
0 3 2 4
*
#
F ire P a n ic
O n O ff
0 5 1 0
F ire P a n ic
O n O ff
0 5 2 0
B
A
B
A u x ilia ry P a n ic
O n O ff
0 5 1 1
A
A u x ilia ry P a n ic
O n O ff
0 5 2 1
A
B
P o lic e P a n ic
O n O ff
0 5 1 2
A
S ire n T im e o u t
4 m in s (1 -3 0 )
0 3 1 3
A
A
E n try L ig h ts
N o n e (3 -9 )
0 4 1 0
#
B
E x te n d e d D e la y
4 m in s (1 -8 )
0 3 2 2
A
B
*
#
E n try L ig h ts
N o n e (3 -9 )
0 4 0 0
H o u s e C o d e
1 B (1 -2 5 5 )
0 4 0 1
A
*
A
B
P o lic e P a n ic
O n O ff
0 5 2 2
A
B
B
A
S ta r is N o D e la y
O n O ff
0 5 1 4
A
K e y c h a in T P
A rm O n O ff
0 5 2 3
K e y c h a in T P
A rm O n O ff
0 5 1 3
B
A
S ta r is N o D e la y
O n O ff
0 5 2 4
A
A c t. T im e o u t
2 4 h o u rs (1 -4 2 )
0 3 0 5
B
A
D a y lig h t S a v .
O n O ff
8 6 9 0 G 0 6 B .D S F
0 3 0 6
Concord
77
T IE R 2 M E N U S (c o n t.)
#
R e p o rtin g
*
#
B
G lo b a l
P a rtitio n 1
A
*
#
2 4 H o u r T a m p e r
O n O ff
0 6 0 0 0
A
B
A
A
0 6 1 0 2
B
A
L o w C P U
B a tte ry O n O ff
0 6 0 0 4
B
0 6 1 0 4
A
B
B
A
A
0 6 0 0 7
A la rm V e rify
O n O ff
0 6 1 0 8
B
B
A
T P P a n ic R P T
F M T O n O ff
0 6 0 0 9
B
A
S e n s o r P tn
n
B
A
S e n s o r G ro u p
n n
A
B
A
A
8 6 9 0 G 0 7 B .D S F
A
B
A
A
A
T w o T rip E rro r
O n O ff
0 6 0 0 8
A
D o n e
B
F re e z e A la rm
O n O ff
0 6 2 0 7
B
B
A
A
B
A
F re e z e A la rm
O n O ff
0 6 1 0 7
Z o n e R e s to ra ls
O n O ff
S n P 1 G n n
N C /N O /T P
R F /H W
0 6 2 0 6
B
A
B
T rip
S e n s o r n
L a tc h k e y F o rm a t
O n O ff
0 6 1 0 6
0 6 0 0 6
B
*
#
D e le te S e n s o r
n
A
S n n Ite m 0
0 -
*
#
G lo b a l F ire
O n O ff
0 7 0 4
B
L a tc h k e y F o rm a t
O n O ff
B u ffe r F u ll R p t
O n O ff
S e n s o r G ro u p
0 *
B
*
E d it S e n s o r
0 8 3
A
F o rc e A rm e d
O n O ff
0 6 2 0 5
0 6 1 0 5
0 6 0 0 5
A
0 8 2
S W S S u p v C o d e
3 (1 -2 5 5 )
0 7 0 3
A
B
F o rc e A rm e d
O n O ff
B a tt. R e s to ra l
T e x t fo r
S e n s o r
n
B
E d it S e n s o r
A
#
B
A
B
0 8 1
S e n s o r P a rtitio n
1
U L 9 8 O p tio n s
O n O ff
0 7 0 2
A
B
*
B
S e n s o r T e s t
A
#
A
B
D u re s s O p tio n
O n O ff
0 6 2 0 4
B
A
A
B
A
D u re s s
O n O ff
*
D is a b le T ro u b le
B e e p s O n O ff
0 7 0 1
N o A c tiv ity
O n O ff
0 6 2 0 3
B
B
0 8 0
S ire n V e rify
O n O ff
0 7 1 0
B
R e c e n t C lo s in g s
O n O ff
0 6 2 0 2
A
N o A c tiv ity
O n O ff
0 6 1 0 3
0 6 0 0 3
B
B
B
A
A
B
L e a rn S e n s o rs
P a rtitio n 1
#
Im m e d ia te
B e e p s O n O ff
0 7 0 0
C lo s in g R p ts
O n O ff
0 6 2 0 1
R e c e n t C lo s in g s
O n O ff
B y p a s s R e p o rts
O n O ff
A la rm V e rify
O n O ff
0 6 2 0 8
B
A
S y s te m T a m p e r
O n O ff
0 6 1 0 9
A
S y s te m T a m p e r
O n O ff
0 6 2 0 9
A
A C F a ilu re
O n O ff
0 6 0 1 0
78
A
C lo s in g R p ts
O n O ff
0 6 1 0 1
B a c k in S e rv ic e
O n O ff
0 6 0 0 2
B
B
B
B u ffe r C o n tro l
O n O ff
0 6 0 0 1
*
#
*
#
A
O p e n in g R p ts
O n O ff
0 6 2 0 0
O p e n in g R tp s
O n O ff
0 6 1 0 0
S e n s o rs
*
B
G lo b a l
*
#
*
#
P a rtitio n 2
A
*
#
B
*
B
#
S ire n O p tio n s
A
B
R e c e iv e r F a il
O n O ff
0 6 0 1 1
A
B
R F L o w B a t R p t
W e e k ly
D a ily
0 6 0 1 2
A
B
R F S u p v R p t
W e e k ly
D a ily
0 6 0 1 3
A
B
S w in g e r L im it
1 (1 -2 )
0 6 0 1 4
A
B
P ro g ra m
R e p o rt
O n O ff
0 6 0 1 5
Concord
T IE R 2 M E N U S (c o n t.)
#
A u d io V e rific a tio n
*
#
A c c e s s o ry M o d u le s
*
P a rtitio n 1
*
#
U n it - ID
1 0 0 n n (n n = 0 0 -1 5 )
B
A
*
#
A u d io M o d e
1 (1 -3 )
0 9 0 1
B
P a rtitio n 1
A
*
#
A u d io V e rify
O n O ff
0 9 0 0
B
M in im u m o f 1 6
b u s d e v ic e s
B u s D e v ic e s
*
#
*
#
B
O u tp u t
P ro g ra m m in g
A
*
#
A
O u tp u t
T e s t
*
#
F ire S h u td o w n
O n O ff
0 9 0 2
B
A
S ile n t T a lk b a c k
O n O ff
0 9 0 3
B
O u tp u t 1
B
A
A
A c c e s s T im e o u t
9 0 s e c s (3 0 -3 0 0 )
0 9 0 4
B
*
#
A
B e e p D e la y
2 s e c s (0 -3 0 0 )
0 9 0 5
B
B
O u tp u t 2
A
B
O u tp u t 3
A
*
#
*
#
O u tp u t 4
A
*
#
P a rtitio n A s s ig n
1 2
1 0 1 0 0 0
B
A
P a rtitio n A s s ig n
1 2
1 0 1 0 1 0
B
A
P a rtitio n A s s ig n
1 2
1 0 1 0 2 0
B
A
P a rtitio n A s s ig n
1 2
1 0 1 0 3 0
C o n fig u ra tio n
0 1 4 0 0
1 0 1 0 0 1
C o n fig u ra tio n
0 0 4 1 0
1 0 1 0 1 1
C o n fig u ra tio n
0 0 9 0 3
1 0 1 0 1 2
C o n fig u ra tio n
0 1 0 0 3
1 0 1 0 1 3
B
A
A c c e s s C o d e
0 9 0 6
* * * *
1 0 1 1 0
C h a n g e ID
D e v ic e
P a rtitio n
A
*
#
D e v ic e ID
n n n n n n n n
B
#
P a rtitio n
A s s ig n
1 2
K e y p a d
O p tio n s
A
*
B
K e y B e e p s
O n O ff
O u tp u ts
*
B
A
#
C e llu la r
S y s te m
A B
O u tp u t n
B
1 0 1 1 1
O u tp u t 2
Ite m n
B
O u tp u t 3
A 1 0 1 1 2
*
#
O u tp u t 1
Ite m n
C e llu la r
O p tio n s
A
*
#
F re e ze T e m p
4 2 ° F (4 0 °-9 0 °F )
A
B
A
*
#
S ta tu s B e e p
O n O ff
B
E n e rg y
O p tio n s
A
*
#
B
B
O u tp u t 2
A
#
B
B
O u tp u t 1
T h e m e n u s a v a ila b le w ill d e p e n d o n S u p e rB u s
d e v ic e (s ) in s ta lle d .
*
#
O u tp u t 3
Ite m n
O u tp u t 4
A 1 0 1 1 3
#
*
O u tp u t 4
Ite m n
*
A
T e m p e ra tu re
(4 0 °-9 0 °F )
P a rtitio n
A s s ig n
1 2
B
A
8 6 9 0 G 0 8 B .D S F
C o n fig u ra tio n
* * * * *
Concord
79
T IE R 2 M E N U S (c o n t.)
B
P re s s B to re tu rn
to S e c u r ity M e n u
B
O n b o a rd O p tio n s
A
*
#
A
B
In p u ts
A
*
#
O u tp u t
P ro g ra m m in g
#
*
T w o W ire S m k
O n O ff
1 1 0 1
B
1 1 1 0 n
P a rtitio n A s s ig n
1 2
1 1 1 0 0
B
A
C o n fig u ra tio n
0 1 6 1 4
1 1 1 1 n
1 1 2 0
*
#
*
#
P a rtitio n A s s ig n
1 2
1 1 1 1 0
B
B
O u tp u t 1
O u tp u t 2
A
*
1 1 1 0 1
*
#
O u tp u t 1
#
O u tp u t
T e x t
A
*
#
S m o k e V e rify
O n O ff
1 1 0 0
B
O u tp u t 1
Ite m n
1 1 2 0 0
O u tp u t 2
1 1 2 1
A
*
#
O u tp u t 2
Ite m n
1 1 2 1 0
A
C o n fig u ra tio n
0 1 7 1 0
1 1 1 1 1
8 6 9 0 G 0 9 B .D S F
80
Concord
System Wiring Notes
Note 1
Class II power transformer must be plugged into an
unswitched AC power receptacle. Do not short the
transformer terminals together. The transformer contains an internal fuse that permanently disables the output if the terminals are shorted.
Note 2
An alphanumeric touchpad is required for on-site programming.
Note 3
Speaker terminals 7 and 8 activate only for alarms in
partition 1. Use speakers with an 8-ohm or higher
impedance. When connecting two or more 8-ohm
speakers, they must be wired in series as shown in the
wiring diagram. Wiring two or more 8-ohm speakers in
parallel can permanently damage the panel.
Note 4
Onboard outputs 1 and 2 are open-collector type rated
for 200 mA maximum. Output 1 defaults to configuration number 01614 (exterior siren). Output 2 defaults to
configuration number 01710 (interior siren). Refer to
panel installation instructions for all possible settings.
Note 5
Zone (loop) wiring shown is an example that applies to
all zones (except when zone 8 is configured for 2-wire
smoke detectors). Install EOL resistors across all
unused zone (loop) inputs.
Concord
Note 6
For UL Listed installations, wire multiple supervised
hardwire smoke detectors (10 maximum) only as
shown. Maximum 10 uA current draw per detector.
Maximum 80 mA current draw in alarm.
Note 7
Some telephones are polarity-sensitive. Green and red
wires may need to be reversed.
Note 8
A maximum of two Audio Verification Modules (60677) are allowed (partition 1 only). Wire multiple
speakers in series, and power and microphone wires in
parallel. Use shielded cable where shown in diagram to
prevent cross-talk between the speaker and microphone. Audio Verification Modules shall not be used in
UL Listed installations.
Note 9
Connect multiple piezo sirens in parallel. Slim Line
Hardwire Interior Siren status volume switch settings
have no effect.
Note 10
Refer to the SuperBus 2000 Energy Saver Module
Installation Instructions for thermostat wiring details.
Note 11
Wire Hardwire Module zone (loop) inputs as shown for
the panel. Install EOL resistors across all unused zone
(loop) inputs. Refer to the Module Installation Instructions for complete details.
81
ALL PANEL TERMINAL CONNECTIONS ARE CLASS II POWER LIMITED
6
7
9
8
10
11
12
13
GND
ZONE
3
ZONE
4
14
15
16
GND
ZONE
5
ZONE
6
GND
ZONE
7
17
18
19
20
21
2-WIRE
SMOKE
POWER
+
TELCO
TIP
HOUSE
TIP
HOUSE
RING
TELCO
RING
22
23
24
25
26
27
NOTE 4
NOTE 3:
13-060
(15 WATT)
8 - OHM
SPEAKER
CLASS II
24 VAC
30 OR 50 VA
7
8
NOTE 1: CLASS II POWER
TRANSFORMER
60-761, 60-762,
60-778, or 60-779
NOTE 5:
PIR MOTION
SENSOR 13-082
NOTE 5:
NORMALLY
CLOSED
(N/C)
CONTACTS
IN SERIES
SPEAKER
NOTE 5:
NORMALLY
OPEN
(N/O)
CONTACTS
IN PARALLEL
NOTE 3:
2 8-OHM
SPEAKERS
IN SERIES
(16 OHMS)
2k Ohm
EOL RESISTOR
49-454
- +
2k Ohm EOL
RESISTOR 49-454
(LOCATE AT
LAST DEVICE)
SPLICE
NOTES 3 & 8:
AUDIO VERIFICATION MODULE, 60-677
LP
NOTES 4 & 9:
SLIM LINE HARDWIRE
INTERIOR SIREN
60-483-01
-
+
-
+
NOTE 6:
2-WIRE
HARDWIRE
SMOKE/HEAT
DETECTOR
(10 MAXIMUM)
BRN
GRY
GRN
RED
LN
2k Ohm EOL
RESISTOR
49-454
(LOCATE AT
SENSOR)
NOTE 3: HARDWIRE INTERIOR SPEAKER 60-528
DB-8
CORD
NOTE 7:
RJ-31X (CA-38A)
PHONE JACK
RED
NOTE 2:
SUPERBUS 2000 FIXED
DISPLAY TOUCHPAD (60-820)
OR
2X16 LCD ALPHANUMERIC
TOUCHPAD (60-746-01)
ZONE
2
GREEN
5
ZONE
1
BLACK
4
MIC.
IN
BROWN
3
SPEAKER
OUTPUT OUTPUT
2
1
GREEN
BUS
B
WHITE
2
BUS
A
GREEN
1
GND
+ 12
BUS
RED
24
VAC
BLACK
24
VAC
ZONE
8
2-WIRE
SMOKE
IN
RED
(See notes on other side.)
8690G13A.DSF
GRAY
SYSTEM WIRING DIAGRAM
2k Ohm EOL
RESISTOR 49-454
(LOCATE AT LAST
DETECTOR)
WHITE OR
YELLOW
TO PANEL
TERMINAL 4
TELCO
PROTECTOR
BLOCK
NOTES 4 & 9:
HARDWIRE
EXTERIOR
SIREN 13-046
NOT
USED
PHONE
CONNECTIONS
TIP
(+)
RING
(-)
GRN
RED
RJ-31X
PHONE
LINE
WIRE
RUN
BLACK
GREEN
YELLOW
RED
1
2
3
HIGH GND LOW
SPLICE
SEPARATE
WIRE
CABLES
8
OPTIONAL SUPERBUS 2000 MODULE CONNECTIONS
PANEL
5
TERMINALS
4
PANEL
TERMINALS
3
4
6
3
5
THERMOSTAT
NOTE 10: SUPERBUS 2000
ENERGY SAVER MODULE
60-620-01
TO FURNACE
1
2
3
4
5
6
NOTE 11: SUPERBUS 2000
4-RELAY OUTPUT MODULE
60-770
5
6
3
DB-8
CORD
1
+ 1 2 V
A
2
B
3
4
G N D
5
G N D
6
7
S P K 1 S P K 2
8
9
1 0
A U D 1 A U D 2 G N D
1 1
T IP 1
1 2
T IP 2
1 3
R IN G
2
1 4
R IN G
1
PLUG
BRN
GRY
GRN
RED
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
ZONE 8
ZONE COMMON
ZONE 7
ZONE 6
ZONE COMMON
ZONE 5
ZONE 4
ZONE COMMON
ZONE 3
ZONE 2
ZONE COMMON
ZONE 1
4
ZONE COM
ZONE 1
NO 4
COM 4
NC 4
NO 3
COM 3
NC 3
NO 2
COM 2
NC 2
NO 1
COM 1
NC 1
PANEL
TERMINALS
NOTE 11:
SUPERBUS 2000 8Z
INPUT MODULE 60-774
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18
NOTES 3 & 7: SUPERBUS 2000 PHONE INTERFACE/VOICE MODULE 60-777-01
6
GND
+12V
3
4
A BUS B
5
PANEL TERMINALS
6
SPEAKER
7
GRN
BRN
GRY
RED
24
25
26
27
8
(PARTITION 1
VOICE MODULE
ONLY)
RED
7
4
3
9
10
GRAY
11
N O T
U S E D
4
BROWN
3
TO
PREMISES
PHONES
BLACK
4
GREEN
CABLE
SHIELD
WIRE
RED
TO PANEL TERMINALS 7 & 8
OR
PHONE INTERFACE/VOICE MODULE
TERMINALS 6 & 7
WHITE
OR
YELLOW
NOTE 7:
RJ-31X (CA-38A)
PHONE JACK
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement