E83018-00
CREWMAN
™
DC2000
20” Dust Control
Electric Burnisher
Operator and Parts
Manual
1001 Brown Avenue • Toledo, Ohio 43607-0127
Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com
1
General Instructions for the CREWMAN
™
DC2000
Operating Instructions Maintenance
Check machine for damage to cord or plug.
To maintain appearance - wipe the machine with a damp cloth after use.
Use only Hi Speed Burnishing pads 20” or 19” diameter.
Warning - Unplug the machine before servicing
To install or change the pad:
1. Unplug the machine.
2. Tip the machine back on the wheels.
3. Remove the center-lock.
4. Center the pad on the pad driver.
5. Replace the center-lock and tighten securely.
To operate the machine:
1. Plug into a grounded outlet.
2. Release the handle and lower it.
3. The handle can be locked into a comfortable position for the operator or used free fl oating.
4. Press the safety lever and squeeze the trigger to start
The operator should check the following at 250 hour intervals:
1. Check the motor brushes for wear or
2. Check the cord and electrical system.
3. Check the safety lockout on the trigger.
4. Check wheels and bearings.
5. Check the Dust shroud and brush seal.
6. Check the Dust bag before each use.
5. Do not operate in one place as damage to the fl oor or fi nish could result.
6. The machine should be operated in the green area of the meter on the handle. Turn the knob on the back to increase or decrease the pad pressure.
7. Do not operate the machine with the handle in the
8. Remove the pad after every use.
9. Use only new or clean pads and reverse them
Specifi cations:
Length - 30 in.
Width - 22 in.
Height - 50 in.
Weight - 69 Lbs.
Pad Speed - 2000 RPM
Pad Diameter - 20 in.
Drive motor - 1.5 HP, 120v, 15 A, 50/60 HZ
Cord - 14-3 ST, 75 ft.
Safety
Read and understand the manual before operating this machine.
• Do not operate in explosive areas or use near fl ammable liquids or gases.
• Attach only to properly grounded outlet.
• Do not expose to rain, store indoors.
• Do not operate the machine with a damaged
cord plug.
• Do not block or disconnect the safety lever.
• Do not leave the machine plugged in
• Unplug the machine before servicing.
• Do not put fi ngers under the pad or pad holder.
• Unplug the machine before installing or
2
• Use only with Hi Speed Burnishing pads.
BETCO US WARRANTY POLICY
10 Year Coverage
Subject to the conditions stated below, Betco warrants parts and labor on rotationally molded polyethylene tanks/housings and injection molded vacuum head assemblies to be free from defects in materials and workmanship for a period of ten years to the original purchaser.
3 Year Coverage
Subject to the conditions stated below, Betco warrants parts and labor on all other Betco components to be free from defects in materials and workmanship for a period of three years to the original purchaser.
1 Year Coverage
Subject to the conditions stated below, Betco offers a limited warranty on parts and labor on the following equipment: parts and accessories to be free from defects in materials and workmanship for a period of one year to the original purchaser. DM Series Vacuums: #85506-00, #85507-00 Bac Pac Lite
Vacuum: #85903-00 FiberPRO ® Floor Dryer: #85507-00 WORKMAN ™ Series
Vacuums: #85024-00, #85025-00, #85026-00, #85027-00 CV100T Vacuum:
#85023-00. All Tools and Accessories/All Battery Chargers/All Batteries are pro-rated for 1 year.
Allowable Travel Time Warranty Reimbursement:
Eligible equipment: All battery and propane powered equipment products.
Warranty period: 90 days from date of sale to the original purchaser. A maximum 180 mile round trip at 50 cents per mile will be allowed for warranty consideration.
Propane Machine Warranty:
Kawasaki engines are warranted by Kawasaki for a period of 2 years against manufacturer defects. All other components (except wear items)* are warranted by Betco for a period of 3 years.
*Wear Items exempt from Warranty consideration include but may not be limited to: power cords, transport wheels, vacuum bags, belts, squeegee blades, pad drivers, clutch plates, handle grips, fi lters, screens, throttle cables, brushes and carbon brushes.
Subject to the conditions and exceptions stated in this warranty, Betco warrants the Betco products to be free from defects in material and workmanship, under normal use and service, for the periods listed under the warranty policy to the original purchaser. At any time during the warranty period, Betco will furnish replacement parts for the Betco parts to the original purchaser.
Such parts will be furnished and charged including transportation costs, to the original owner through any Betco authorized Service Distributor. If the original part is returned within the warranty policy period from date of delivery for inspection by Betco and is found to be defective the owner will be credited for the cost of replacement parts plus shipping and handling.
Replacement parts that have become defective through wear or abuse are not included in this warranty. This warranty does not apply to damage or defect caused by accident, misuse. Negligence, fi re, or to any Betco product which has been serviced or repaired by other than an authorized Betco Service Distributor or Betco factory personnel. This warranty is void if products are used for any purpose other than that which was intended. There are no other warranties expressed or implied. In no event shall Betco be liable for incidental or consequential damages or any damage to person or property.
(Please note some states do not allow the exclusion or limitations for incidental and consequential damages).
BURNISHER MODEL CREWMAN
™
DC2000
1 E81117 Base,
2
3
4
5
6
7
8
E81174 Plate, Motor Mount
E81173 Bracket, Dust Control Burnisher
E81172 Bracket, Spring Adjustment
E81089 Bolt, 5/16 - 18 X 3/4”
E81063 Nut, 5/16” Nylok
E81085 Bolt, Shoulder 1/2 x 3/8”
E83145 Washer, 1/2” Nylon
9
10
E81076 Nut, 3/8 Nylok Thin
E83651 Axle, 1/2 x 17.25”
11 E81124 Wheel,
12
13
14
15
E83143 Cap, Axle 1/2”
E81126 Wheel, Caster 2.5”
E81082 Bolt, 1/4 - 20 X 3/8 with patch
E81713 Washer, Flat 1/4”
16 E81132 Spring,
17
18
E81393 Rod, Threaded, spring adjustment 5”
E81079 Nut, 1/2”-13 Jam
19 E81109 Motor, 1.5 HP 115v 2000 RPM
19A Internal Motor Parts E85053 Carbon Brush, E85042 Rectifi er
20
21
E81062 Washer, Flat 5/16” USS
E81066 Washer, Lock 3/8” Split
29
30
31
32
33
34
35
22 E81080 Bolt 3/8 - 16 x 3/4” Gr 5
23 E81144 Shroud,
24
25
26
27
28
E83657 Brush, Extrusion, Skirt DC Burnisher
E83425 Screw, 1/4 - 20 X 1” Ph Tr Hd
E81173 Washer, Flat 1/4”
E81078 Washer, Lock 1/4” Split
E81071 Plug, Plastic ratchet 5/16”
E81149 Pad Driver, DC Burnisher
E81072 Bolt, 5/16 X 1”
E81062 Washer, Flat USS 5/16”
E81067 Washer, Lock 5/16” Split
E81142 Cover, DC Burnisher
E81143 Cover, Dust Bag DC Burnisher
E81074 Screw, 10-24 X 1/2 Truss Head Zn
36
37
E83788 Bag, Dust, Cloth
E83720 Decal, Brush Pressure DC Burnisher
38 E81523 Screw, 8-32 x 3/8 Ph Tr Hd
39 E81141 Cover,
40
41
42
E81229 Knob, black, DC Burnisher
E83269 Washer, Spring 1/2 in.
E81150 Pad Holder, for replacement only
43 E81088 Nut, 1/2 x 13 thin nylock
3
BURNISHER MODEL CREWMAN
™
DC2000 PARTS
W B
120 V
G
B
METER
ELECTRICAL SCHEMATIC
Not Shown EP50065 Cam Lock Handle Asm
Not Shown E85042 Rectifi er
Not Shown E85053 Carbon Brush Set of 4
W
B
G
MOTOR
1
2
E83523 Nylon Cable Tie
E83132 Cord, Handle, 14-3
3
4
5
6
E83789 Nut, Electrical Conduit, 1/2”
E83790 Cord, 50 Feet, 14-3ST
E83496 Strain Relief for Replacement
E81064 Bolt, Hex. 1/4-20 x 3/4
7 E83520 Nut, Nylock, 1/4-20
8 E83127 Grip
9 E83651 Screw, Phillips, No. 6x1
10 E83426 Screw, Phillips, 1/4-20 x 1.75”
11 E83130 Spring
12 E83270 Clip,
13 E85032 Switch
14 E83129 Safety
15 E82752 Trigger,
16 E83325 Cover, Switch Box
17 EP50300 Switch Box Cover, Handle, Dual Speed
18 E81105 Plate,
19
20
21
22
E83451 Handle Tube, 7/8 x 16
E81065 Bolt, Hex. 1/4-20 x 1.75” Grade 5
E81070 Nut, Nylock, 1/4-20
E83519 Grommet, .375” ID
23 E83137 Cord
24 E83135 Oval
25 E83133 Cam Lock Lever W/Pin & Bolt
PE50064 Cam Lock Assembly Includes items 24, 25, 27, 28, 30
26
27
E81379 Washer, Spring, 3/8
E81063 Nut, Nylock, 5/16-18
28 E83145 Washer,
29
30
E81077 Bolt, Shoulder, 3/8 x 1
E83269 Washer, Spring, 1/2
31 E83143 Caps, Axle, 0.5
32 E82717 Handle
33 E83136 Bracket, Flat Handle
34 E83711 Handle
35
36
E81394 Axle, 1/2 x 6.625”
E81216 Meter, 15 Amp.
4
1001 Brown Avenue • Toledo, Ohio 43607-0127
Customer Service: 888-GO-BETCO • Fax: 800-445-5056 • Technical Service: 877-856-5954 • www.betco.com
E83018-00 July12X
