Asus T3-P5G965 Personal Computer User manual

Asus T3-P5G965 Personal Computer User manual

advertisement

Assistant Bot

Need help? Our chatbot has already read the manual and is ready to assist you. Feel free to ask any questions about the device, but providing details will make the conversation more productive.

Manual
Asus T3-P5G965 Personal Computer User manual | Manualzz
T3-P5G965
ASUS PC (Desktop Barebone)
E3290
June 2007
Copyright © 2007 ASUSTeK COMPUTER INC. All Rights Reserved.
No part of this manual, including the products and software described in it, may be reproduced,
transmitted, transcribed, stored in a retrieval system, or translated into any language in any form
or by any means, except documentation kept by the purchaser for backup purposes, without the
express written permission of ASUSTeK COMPUTER INC. (“ASUS”).
Product warranty or service will not be extended if: (1) the product is repaired, modified or
altered, unless such repair, modification of alteration is authorized in writing by ASUS; or (2) the
serial number of the product is defaced or missing.
ASUS PROVIDES THIS MANUAL “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESS
OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OR CONDITIONS OF
MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ASUS,
ITS DIRECTORS, OFFICERS, EMPLOYEES OR AGENTS BE LIABLE FOR ANY INDIRECT, SPECIAL,
INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF PROFITS, LOSS
OF BUSINESS, LOSS OF USE OR DATA, INTERRUPTION OF BUSINESS AND THE LIKE), EVEN IF ASUS
HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES ARISING FROM ANY DEFECT OR
ERROR IN THIS MANUAL OR PRODUCT.
SPECIFICATIONS AND INFORMATION CONTAINED IN THIS MANUAL ARE FURNISHED FOR
INFORMATIONAL USE ONLY, AND ARE SUBJECT TO CHANGE AT ANY TIME WITHOUT NOTICE, AND
SHOULD NOT BE CONSTRUED AS A COMMITMENT BY ASUS. ASUS ASSUMES NO RESPONSIBILITY
OR LIABILITY FOR ANY ERRORS OR INACCURACIES THAT MAY APPEAR IN THIS MANUAL,
INCLUDING THE PRODUCTS AND SOFTWARE DESCRIBED IN IT.
Products and corporate names appearing in this manual may or may not be registered
trademarks or copyrights of their respective companies, and are used only for identification or
explanation and to the owners’ benefit, without intent to infringe.
ii
Table of contents
Notices................................................................................................. vi
Safety information...............................................................................vii
About this guide..................................................................................viii
System package contents..................................................................... x
Chapter 1: System introduction
1.1
Welcome!............................................................................... 1-2
1.2
Front panel (external)............................................................ 1-2
1.3
Front panel (internal)............................................................. 1-3
1.4
Rear panel.............................................................................. 1-4
1.5
Internal components.............................................................. 1-6
Chapter 2: Basic installation
2.1
Preparation............................................................................ 2-2
2.2
Before you proceed............................................................... 2-2
2.3
Removing the cover............................................................... 2-3
2.4
Removing the power supply unit........................................... 2-4
2.5
CPU installation...................................................................... 2-5
2.6
2.7
2.5.1
Installing the CPU..................................................... 2-5
2.5.2
Reinstalling the CPU fan and heatsink assembly...... 2-7
Installing a DIMM.................................................................... 2-8
2.6.1
Memory configurations............................................ 2-8
2.6.2
DIMM installation.................................................... 2-12
Installing an expansion card................................................. 2-13
2.7.1
Expansion slots...................................................... 2-13
2.7.2
Expansion card installation..................................... 2-14
2.8
Installing an optical drive..................................................... 2-15
2.9
Installing a Serial ATA disk drive.......................................... 2-16
2.10 Reinstalling the power supply unit....................................... 2-17
2.11 Replacing the cover............................................................. 2-18
Chapter 3: Starting up
3.1
Installing an operating system............................................... 3-2
3.2
Powering up........................................................................... 3-2
3.3
Support CD information......................................................... 3-2
3.3.1
Running the support CD........................................... 3-3
iii
Table of contents
3.3.2
Drivers menu............................................................ 3-3
3.3.3
Utilities menu........................................................... 3-4
3.3.4
ASUS contact information....................................... 3-6
3.3.5
Other information.................................................... 3-6
Chapter 4: Motherboard info
4.1
Introduction........................................................................... 4-2
4.2
Motherboard layout............................................................... 4-2
4.3
Jumpers................................................................................. 4-3
4.4
Connectors............................................................................ 4-5
Chapter 5: BIOS setup
5.1
5.2
5.3
Managing and updating your BIOS......................................... 5-2
5.1.1
ASUS EZ Flash 2 utility............................................. 5-3
5.1.2
AFUDOS utility......................................................... 5-4
5.1.3
ASUS CrashFree BIOS 2 utility................................. 5-6
5.1.4
ASUS Update utility................................................. 5-8
BIOS setup program............................................................. 5-11
5.2.1
BIOS menu screen.................................................. 5-12
5.2.2
Menu bar................................................................ 5-12
5.2.3
Navigation keys...................................................... 5-12
5.2.4
Menu items............................................................ 5-13
5.2.5
Sub-menu items..................................................... 5-13
5.2.6
Configuration fields................................................ 5-13
5.2.7
Pop-up window....................................................... 5-13
5.2.8
Scroll bar................................................................ 5-13
5.2.9
General help........................................................... 5-13
Main menu............................................................................ 5-14
5.3.1
5.4
5.3.2
System Date ......................................................... 5-14
5.3.3
SATA1, SATA2, and SATA3.................................. 5-15
5.3.4
IDE Configuration................................................... 5-16
5.3.5
System Information............................................... 5-17
Advanced menu................................................................... 5-17
5.4.1
iv
System Time . ....................................................... 5-14
USB Configuration.................................................. 5-18
Table of contents
5.5
5.6
5.7
5.8
5.4.2
CPU Configuration.................................................. 5-19
5.4.3
Chipset................................................................... 5-20
5.4.4
Onboard Devices Configuration.............................. 5-22
5.4.5
PCI PnP................................................................... 5-23
Power menu......................................................................... 5-25
5.5.1
Suspend Mode ...................................................... 5-25
5.5.2
Repost Video on S3 Resume ................................ 5-25
5.5.3
ACPI 2.0 Support .................................................. 5-25
5.5.4
ACPI APIC Support ................................................ 5-25
5.5.5
APM Configuration................................................. 5-26
5.5.6
Hardware Monitor................................................... 5-27
Boot menu........................................................................... 5-28
5.6.1
Boot Device Priority............................................... 5-28
5.6.2
Boot Settings Configuration.................................. 5-29
5.6.3
Security.................................................................. 5-30
Tools menu.......................................................................... 5-32
5.7.1
ASUS EZ Flash 2..................................................... 5-32
5.7.2
ASUS O.C. Profile................................................... 5-33
Exit menu............................................................................. 5-34
Appendix
Power supply specifications.............................................................. A-2
Notices
Federal Communications Commission Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions:
• This device may not cause harmful interference, and
• This device must accept any interference received including
interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with
manufacturer’s instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment to an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
WARNING! The use of shielded cables for connection of the monitor to
the graphics card is required to assure compliance with FCC regulations.
Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
Canadian Department of Communications Statement
This digital apparatus does not exceed the Class B limits for radio noise
emissions from digital apparatus set out in the Radio Interference
Regulations of the Canadian Department of Communications.
This class B digital apparatus complies with Canadian ICES-003.
vi
Safety information
Electrical safety
• To prevent electrical shock hazard, disconnect the power cable from
the electrical outlet before relocating the system.
• When adding or removing devices to or from the system, ensure that
the power cables for the devices are unplugged before the signal cables
are connected.
• If the power supply is broken, do not try to fix it by yourself. Contact a
qualified service technician or your retailer.
Operation safety
• Before installing devices into the system, carefully read all the
documentation that came with the package.
• Before using the product, make sure all cables are correctly connected
and the power cables are not damaged. If you detect any damage,
contact your dealer immediately.
• To avoid short circuits, keep paper clips, screws, and staples away from
connectors, slots, sockets and circuitry.
• Avoid dust, humidity, and temperature extremes. Do not place the
product in any area where it may become wet. Place the product on a
stable surface.
• If you encounter technical problems with the product, contact a
qualified service technician or your retailer.
Lithium-Ion Battery Warning
CAUTION: Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recommended by
the manufacturer. Dispose of used batteries according to the
manufacturer’s instructions.
VORSICHT: Explosionsgetahr bei unsachgemäßen Austausch der
Batterie. Ersatz nur durch denselben oder einem vom Hersteller
empfohlenem ähnljchen Typ. Entsorgung gebrauchter Batterien nach
Angaben des Herstellers.
LASER PRODUCT WARNING
CLASS 1 LASER PRODUCT
vii
About this guide
Audience
This guide provides general information and installation instructions
about the ASUS T3-P5G965 barebone system. This guide is intended for
experienced users and integrators with hardware knowledge of personal
computers.
How this guide is organized
This guide contains the following parts:
1. Chapter 1: System introduction
This chapter gives a general description of the ASUS T2-PH1. The
chapter lists the system features, including introduction on the front
and rear panel, and internal components.
2. Chapter 2: Basic installation
This chapter provides step-by-step instructions on how to install
components in the system.
3. Chapter 3: Starting up
This chapter helps you power up the system and install drivers and
utilities from the support CD.
4. Chapter 4: Motherboard information
This chapter gives information about the motherboard that comes
with the system. This chapter includes the motherboard layout,
jumper settings, and connector locations.
5. Chapter 5: BIOS information
This chapter tells how to change system settings through the BIOS
Setup menus and describes the BIOS parameters.
6. Appendix
The Appendix includes the power supply unit specification for this
system.
viii
Conventions used in this guide
WARNING: Information to prevent injury to yourself when trying
to complete a task.
CAUTION: Information to prevent damage to the components
when trying to complete a task.
IMPORTANT: Instructions that you MUST follow to complete a
task.
NOTE: Tips and additional information to aid in completing a
task.
Where to find more information
Refer to the following sources for additional information and for product
and software updates.
1. ASUS Websites
The ASUS websites worldwide provide updated information on
ASUS hardware and software products. Refer to the ASUS contact
information.
2. Optional Documentation
Your product package may include optional documentation, such as
warranty flyers, that may have been added by your dealer. These
documents are not part of the standard package.
ix
System package contents
Check your T3-P5G965 system package for the following items.
If any of the items is damaged or missing, contact your retailer
immediately.
Item description
1. ASUS T3-P5G965 barebone system with
• ASUS motherboard
• 250 W PFC power supply unit
• Gigabit LAN port
• CPU fan and heatsink assembly
• 1 x 5.25” drive bays
• 2 x 3.5” hard disk drive bay
• 6 x USB 2.0 ports
• 2 x IEEE 1394a ports
• S/PDIF IN&OUT port
• 7-in-1 storage card reader
2. Cables
• AC power cord
• ATA cable
• Serial ATA cable
• Serial ATA power cable
3. Support CD
4. User guide
5. Optional items
• Optical drive (CD-ROM/CD-RW/DVD-ROM/DVD-RW)
This chapter gives a general
description of the ASUS
T3-P5G965. The chapter lists
the system features including
introduction on the front and rear
panel, and internal components.
System introduction
Chapter 1
1.1
Welcome!
Thank you for choosing the ASUS T3-P5G965!
The ASUS T3-P5G965 is an all-in-one barebone system with a versatile
home entertainment feature.
The system comes in a stylish mini-tower casing, and powered by the ASUS
motherboard that supports the Intel® Pentium® 4 processor in the 775-land
package with 533/800/1066 MHz FSB and up to 2 GB system memory.
With audio functions, extensive connectivity, and Gigabit LAN capability,
the T3-P5G965 is designed for the sophisticated.
With these and many more, the T3-P5G965 definitely delivers the cutting
edge technology for your computing and multimedia needs!
1.2
Front panel (external)
The front panel includes the system and audio control buttons, system
LEDs, and LED panel.
1
2
3
4
1-
1.
Drive door. Open this door to access the disk drive.
2.
Power button
3.
HDD LED
. This LED lights up when data is being read from or
written to the hard disk drive.
4.
Front panel I/O door. Push down this door to show the input/output
ports.
. Press this button to turn the system on.
Chapter 1: System introduction
1.3
Front panel (internal)
The optical drive(s), storage card reader slots, and several I/O ports are
located inside the front panel doors.
Open the front panel door by pushing it downwards.
5
6
10
7
11
8
12
9
13
14
5.
Optical Drive (optional). This is for the optical disks.
6.
CompactFlash®/Microdrive™ card slot . This slot is for a
CompactFlash®/Microdrive™ storage card.
7.
Memory Stick®/Memory Stick Pro™ card slot. This slot is for a Memory
Stick®/Memory Stick Pro™ storage card.
8.
USB 2.0 ports
. These Universal Serial Bus 2.0 (USB 2.0) ports
are available for connecting USB 2.0 devices such as a mouse, printer,
scanner, camera, PDA, and others.
9.
S/PDIF In port. This port connects your audio system for 5.1-channel
surround sound and enhanced 3D audio.
2.0
10. Secure Digital™/MultimediaCard slot . This slot is for a Secure
Digital™/MultimediaCard storage card.
11. Eject button. Press this button to eject the optical drive bay.
12. Microphone port
. This Mic (pink) port connects a microphone.
13. Headphone port
mini-plug.
. This port connects a headphone with a stereo
14. 4-pin IEEE 1394a port
. This port provides high-speed
connectivity for IEEE 1394a-compliant audio/video devices, storage
peripherals, and other PC devices.
ASUS T3-P5G965
1-
1.4
Rear panel
The system rear panel includes the power connector and several I/O ports
that allow convenient connection of devices.
27
15
28
16
29
17
30
31
32
LINE
IN
FRONT
MIC IN
19
CTR
BASS
SIDE
SPK
REAR
SPK
18
20
33
34
eSATA
21
22
35
23
36
24
25
26
15. Expansion slot covers. Remove these covers when installing expansion
cards.
16. Expansion slots. Use these slots when installing expansion cards.
17. Rear surround speakers. This port connects to a high-definition sixchannel speaker.
18. Side surround speakers.This port connects to a high-definition sixchannel speaker.
19. Microphone port . This Microphone (pink) port connects a
microphone. In 4/6-channel mode, the function of this port becomes
Low Frequency Enhanced Output/Center.
20. VGA port
. This port connects a VGA monitor.
21. PS/2 mouse port
. This green 6-pin connector is for a PS/2 mouse.
22. External SATA port. This port connects to a SATA hard disk drive.
23. PS/2 keyboard port
PS/2 keyboard.
. This purple 6-pin connector is for a
24. LAN (RJ-45) port . This port allows Gigabit connection to a Local
Area Network (LAN) through a network hub.
2.0
25. USB 2.0 ports
. These Universal Serial Bus 2.0 (USB 2.0) ports
are available for connecting USB 2.0 devices such as a mouse, printer,
scanner, camera, PDA, and others.
1-
Chapter 1: System introduction
26. 6-pin IEEE 1394a port
. This port provides high-speed
connectivity for IEEE 1394a-compliant audio/video devices, storage
peripherals, and other PC devices.
27. Chassis vent. This vent is for the fan that provides ventilation inside
the system chassis.
28. Expansion card lock. This lock secures installed expansion cards. See
page 2-15 for details.
29. S/PDIF Out port. This port connects your audio system for 5.1channel surround sound and enhanced 3D audio.
30. Center & woofer speakers.
31. Line In port . This Line In (light blue) port connects a tape player
or other audio sources. In 6-channel mode, the function of this port
becomes Surround output.
32. Line Out port . This Line Out (lime) port connects a headphone or
a speaker. In 4/6-channel mode, the function of this port becomes
Front Speaker Out.
33. COM port
. This port connects a mouse, modem, or other devices
that conforms with serial specification.
34. Power connector. This connector is for a power cable and plug.
35. Voltage selector. This switch allows you to adjust the system input
voltage according to the voltage supply in your area.
36. Power switch. This switch allows you to turn your PC on/off..
ASUS T3-P5G965
1-
1.5
Internal components
The illustration below is the internal view of the system when you remove
the top cover and the power supply unit. The installed components are
labeled for your reference. Proceed to Chapter 2 for instructions on
installing additional system components.
The illustration shows an open chassis lifted at a 90o angle.
2
1
3
6
5
4
8
7
1-
1.
ASUS motherboard
2.
LGA775 socket with PnP cap
3.
DIMM sockets
4.
Serial ATA connectors
5.
PCI Express™ x16 slot for discrete graphics
card
6.
PCI slot
7.
Expansion card slots
8.
Power supply unit
Chapter 1: System introduction
Chapter 2
Basic installation
This chapter provides step-by-step
instructions on how to install components in the system.
2.1
Preparation
Before you proceed, make sure that you have all the components you plan
to install in the system.
Basic components to install
1. Central Processing Unit (CPU)
2. DDR2 Dual Inline Memory Module (DIMM)
3. Expansion card(s)
4. Hard disk drive
5. Optical drive
Tool
Philips (cross) screw driver
2.2
Before you proceed
Take note of the following precautions before you install components into
the system.
• Use a grounded wrist strap or touch a safely grounded object or
a metal object, such as the power supply case, before handling
components to avoid damaging them due to static electricity.
• Hold components by the edges to avoid touching the ICs on them.
• Whenever you uninstall any component, place it on a grounded
antistatic pad or in the bag that came with the component.
The motherboard comes with an onboard standby power LED. This LED
lights up to indicate that the system is ON, in sleep mode or in soft-off
mode, and not powered OFF. Unplug the power cable from the power outlet
and make sure that the standby power LED is OFF before installing any
system component.
SB_PWR
ON
Standby
Power
OFF
Powered
Off
R
Onboard LED
2-
Chapter 2: Basic installation
2.3
Removing the cover
To remove the cover:
1.
On the rear panel, locate the three screws that secure the cover to
1
the chassis.
FRONT
LINE
IN
MIC IN
SIDE
SPK
CTR
BASS
REAR
SPK
eSATA
1
2.
1
Use a Phillips screw driver to
remove the cover screws. Keep
the screws for later use.
2
2
2
3.
Slightly pull the cover toward
the rear panel until the side
tabs are disengaged from the
chassis.
4.
Lift the cover, then set aside.
4
3
ASUS T3-P5G965
3
2-
2.4
Removing the power supply unit
You need to remove the power supply unit (PSU) before you can install a
central processing unit (CPU) and other system components.
To remove the PSU:
1.
Lay the system chassis on
its side on a flat and stable
surface.
2.
Disconnect the optical drive
power connector.
3.
Locate and remove the two
screws that secures the PSU
to the chassis.
4.
Lift the PSU in the direction of
the arrow to a 90º angle.
When removing the PSU, make sure to hold or support it firmly. The unit
may accidentally drop and damage other system components.
2-
Chapter 2: Basic installation
2.5
CPU installation
• Your boxed Intel® Pentium® 4 LGA775 processor package should come with installation instructions for the CPU, heatsink, and the
retention mechanism. If the instructions in this section do not match the CPU documentation, follow the latter.
• Check your motherboard to make sure that the PnP cap is on the
CPU socket and the socket contacts are not bent. Contact your
retailer immediately if the PnP cap is missing, or if you see any
damage to the PnP cap/socket contacts/motherboard components.
ASUS will shoulder the cost of repair only if the damage is shipment/
transit-related.
• Keep the cap after installing the motherboard. ASUS will process
Return Merchandise Authorization (RMA) requests only if the
motherboard comes with the cap on the LGA775 socket.
• The product warranty does not cover damage to the socket
contacts resulting from incorrect CPU installation/removal, or
misplacement/loss/incorrect removal of the PnP cap.
2.5.1 Installing the CPU
IMPORTANT! Before installing the
CPU, remove the two rubbers (A and
B) attached to the bottom of the
cooler / fan.
A
B
To install a CPU:
1.
Locate the CPU socket on the motherboard.
R
CPU Socket 775
Before installing the CPU, make sure that the socket box is facing
towards you and the load lever is on your left.
ASUS T3-P5G965
2-
2.
Press the load lever with your
thumb (A), then move it to the
left (B) until it is released from
the retention tab.
To prevent damage to the
socket pins, do not remove
the PnP cap unless you are
installing a CPU.
3.
4.
Retention tab
A
B
Load lever
Lift the load lever in the
direction of the arrow to a 135º
angle.
PnP cap
Load plate
Lift the load plate with your
thumb and forefinger to a 100º
angle (4A), then push the PnP
cap from the load plate window
to remove (4B).
4B
4A
3
5.
Position the CPU over the
socket, making sure that
the gold triangle is on the
bottom‑left corner of the socket
then fit the socket alignment
key into the CPU notch.
CPU notch
Gold
triangle
mark
Alignment key
2-
Chapter 2: Basic installation
6.
Close the load plate (A), then
push the load lever (B) until it
snaps into the retention tab.
A
B
2.5.2 Reinstalling the CPU fan and heatsink
assembly
To reinstall the CPU fan and heatsink assembly:
1.
Position the CPU fan and heatsink assembly on top of the installed
CPU.
2.
Drive in the four screws you removed earlier into the CPU fan screw
holes to secure the fan and heatsink assembly to the motherboard.
3.
Connect the CPU fan cable to the CPU fan connector on the
motherboard.
2
2
2
2
1
ASUS T3-P5G965
2-
2.6
Installing a DIMM
The system motherboard comes with two Double Data Rate 2 (DDR2) Dual
Inline Memory Module (DIMM) sockets.
The following figure illustrates the location of the sockets:
DIMM_A1
DIMM_A2
DIMM_B1
DIMM_B2
128 Pins
112 Pins
R
240-pin DDR2 DIMM Sockets
2.6.1 Memory configurations
You may install up to 4 GB system memory using 256 MB, 512 MB, and
1 GB DDR2 DIMMs.
• Installing DDR2 DIMMS other than the recommended configurations
may cause memory sizing error or system boot failure. Use any of
the recommended configurations in the table on the next page.
• Install only identical (the same type and size) DDR2 DIMMs in
DIMM_A1 and DIMM_B1.
• Always install DIMMs with the same CAS latency. For optimum
compatibility, we recommend that you obtain memory modules from
the same vendor.
• Due to chipset resource allocation, the system may detect less than
2 GB system memory when you installed two 1 GB DDR2 memory.
• If installing only one DDRII DIMM, pease install it in DIMM_A1 or A2
first.
• This motherboard does not support memory modules made up of
128 Mb chips or double-sided x16 memory modules.
2-
Chapter 2: Basic installation
Recommended memory configurations
Mode
Single Channel
Dual-channel (1)
Dual-channel (2)
ASUS T3-P5G965
Sockets
DIMM_A1
Populated
-
DIMM_A2
-
Populated
DIMM_B1
DIMM_B2
-
-
-
-
-
-
-
-
-
-
-
-
Populated
-
Populated
-
Populated
Populated
Populated
-
Populated
Populated
Populated
2-
DDR2 (667 MHz) Qualified Vendors List
DIMM support
2-10
Size
Vendor
Component
A B C
512MB
KINGSTON
E5108AE-6E-E
Model
SS
SS/DS
KVR667D2N5/512
v vv
1024MB
KINGSTON
E5108AE-6E-E
DS
KVR667D2N5/1G
v vv
512MB
KINGSTON
E5108AE-6E-E
SS
KVR667D2E5/512
v vv
256MB
KINGSTON
HYB18T256800AF3
SS
KVR667D2N5/256
v vv
512MB
KINGSTON
D6408TEBGGL3U
SS
KVR667D2N5/512
v vv
1024MB
KINGSTON
D6408TEBGGL3U
DS
KVR667D2N5/1G
v vv
256MB
KINGSTON
HYB18T256800AF3S
SS
KVR667D2N5/256
v vv
256MB
Qimonda
HYB18T512160AF-3S
SS
HYS64T32000HU-3S-A
v vv
512MB
Qimonda
HYB18T512800AF3S
SS
HYS64T64000HU-3S-A
v vv
1024MB
Qimonda
HYB18T512800AF3S
DS
HYS64T128020HU-3S-A
v vv
256MB
Qimonda
HYB18T256800AF3S(ECC)SS
HYS72T32000HU-3S-A
v vv
512MB
Qimonda
HYB18T512800AF3S(ECC)SS
HYS72T64000HU-3S-A
v v
1024MB
Qimonda
HYB18T512800AF3S(ECC)DS
HYS72T128020HU-3S-A
v vv
512MB
Qimonda
HYB18T512800BF3S(ECC)SS
HYS72T64000HU-3S-B
v vv
1024MB
Qimonda
HYB18T512800BF3S(ECC)DS
HYS72T128020HU-3S-B
v vv
256MB
Qimonda
HYB18T512160BF-3S
SS
HYS64T32000HU-3S-B
v vv
512MB
Qimonda
HYB18T512800BF3S
SS
HYS64T64000HU-3S-B
v vv
1024MB
Qimonda
HYB18T512800BF3S
DS
HYS64T128020HU-3S-B
v vv
256MB
SAMSUNG
K4T51163QC-ZCE6
SS
M378T3354CZ0-CE6
v v
512MB
SAMSUNG
ZCE6K4T51083QC
SS
M378T6553CZ0-CE6
v vv
1024MB
SAMSUNG
ZCE6K4T51083QC
DS
M378T2953CZ0-CE6
v vv
1024MB
SAMSUNG
ZCE6K4T51083QC
DS
M378T2953CZ3-CE6
v v
512MB
Hynix
HY5PS12821AFP-Y5
SS
HYMP564U64AP8-Y5
v vv
1024MB
Hynix
HY5PS12821AFP-Y5
DS
HYMP512U64AP8-Y5
v vv
1024MB
Hynix
HY5PS1G831FP-Y5(ECC) SS
HYMP112U72P8-Y5
v vv
512MB
Hynix
HY5PS12821AFP-Y5(ECC) SS
HYMP564U72AP8-Y5
v vv
1024MB
Hynix
HY5PS12821AFP-Y5(ECC) DS
HYMP512U72AP8-Y5
v vv
512MB
Hynix
HY5PS12821AFP-Y4
SS
HYMP564U64AP8-Y4
v vv
1024MB
Hynix
HY5PS12821AFP-Y4
DS
HYMP512U64AP8-Y4
v vv
512MB
Hynix
HY5PS12821AFP-Y4(ECC) SS
HYMP564U72AP8-Y4
v vv
1024MB
Hynix
HY5PS12821AFP-Y4(ECC) DS
HYMP512U72AP8-Y4
v vv
256MB
CORSAIR
MIII00605
SS
VS256MB667D2
v vv
512MB
CORSAIR
64M8CFEG
SS
VS512MB667D2
v vv
1024MB
CORSAIR
64M8CFEG
DS
VS1GB667D2
v vv
256MB
ELPIDA
E2508AB-6E-E
SS
EBE25UC8ABFA-6E-E
v vv
512MB
ELPIDA
E5108AE-6E-E
SS
EBE51UD8AEFA-6E-E
v vv
512MB
A-DATA
AD29608A8B-3EG
SS
M20AD5Q3H3163J1C52
v vv
512MB
A-DATA
AD29608A8A-3EG
SS
M2OAD5G3H3166I1C52
v vv
1024MB
A-DATA
AD29608A8A-3EG
DS
M2OAD5G3I4176I1C52
v vv
512MB
crucial
Heat-Sink Package
SS
BL6464AA663.8FD
v vv
1024MB
crucial
Heat-Sink Package
DS
BL12864AA663.16FD
v 1024MB
crucial
Heat-Sink Package
DS
BL12864AL664.16FD
v vv
Chapter 2: Basic installation
DIMM support
Size
Vendor
1024MB
Apacer
E5108AE-6E-E
Model
DS
SS/DS
78.01092.420
Component
A B C
v vv
512MB
Apacer
AM4B5708GQJS7E
SS
AU512E667C5KBGC
v vv
1024MB
Apacer
AM4B5708GQJS7E
DS
AU01GE667C5KBGC
v vv
512MB
Apacer
AM4B5708PJS7E
SS
AU512E667C5KBGC
v vv
512MB
Apacer
AM4B5708GQJS7E
SS
AU512E667C5KBGC
v vv
1024MB
Apacer
N/A
DS
AU01GE667C5KBGC
v vv
512MB
Kingmax
KKEA88B4LAUG-29DX
SS
KLCC28F-A8KB5
v vv
1024MB
Kingmax
KKEA88B4LAUG-29DX
DS
KLCD48F-A8KB5
v vv
512MB
Transcend
E5108AE-6E-E
SS
TS64MLQ64V6J
v vv
1024MB
Transcend
E5108AE-6E-E
DS
TS128MLQ64V6J
v vv
512MB
Transcend
J12Q3AB-6
SS
JM367Q643A-6
v vv
1024MB
Transcend
J12Q3AB-6
DS
JM388Q643A-6
v vv
512MB
Veritech
VTD264M8PC5G
SS
GTP512HLTM45EG
v vv
1024MB
Veritech
VTD264M8PC5G
DS
GTP01GHLTM55EG
v vv
512MB
TwinMOS
E5108AE-GE-E
SS
8G-25JK5-EBT
v vv
512MB
TwinMOS
TMM6208G8M30C
SS
8D-23JK5M2ETP
v vv
2048MB
NANYA
NT5TU128M8BJ-3C
DS
NT2GT64U8HB0JY-3C
v vv
1024MB
NANYA
NT5TU128M8BJ-3C
SS
NT1GT64U88B0JY-3C
v vv
512MB
GEIL
Heat-Sink Package
SS
GX21GB5300DC
v vv
512MB
GEIL
Heat-Sink Package
SS
GX21GB5300SDC
v vv
512MB
Aeneon
AET93F30DA
SS
AET660UD00-30DA98Z
v vv
1024MB
Aeneon
AET93F30DA
DS
AET760UD00-30DA98Z
v vv
512MB
Kingbox
EPD264082200-4KI0629 SS
N/A
v vv
1024MB
Kingbox
EPD264082200-4KI0629 DS
N/A
v vv
Obtain DDR DIMMs only from ASUS qualified vendors. Refer to the
Qualified DDR2 533/667 vendors list on this page. Visit the ASUS
website (www.asus.com) for the latest DDR2 Qualified Vendors List.
ASUS T3-P5G965
2-11
2.6.2 DIMM installation
To install a DDR2 DIMM:
1.
Locate the four DIMM sockets on the
motherboard.
2.
Unlock a socket by pressing the retaining clips
outward.
3.
Align a DIMM on the socket such that the
notch on the DIMM matches the break on the
socket.
4.
Firmly insert the DIMM into the socket until
the retaining clips snap back in place and the
DIMM is properly seated.
A DDR2 DIMM is keyed with a notch so that it fits in only one direction.
DO NOT force a DIMM into a socket to avoid damaging the DIMM!
2-12
Chapter 2: Basic installation
2.7
Installing an expansion card
In the future, you may need to install expansion cards. The motherboard
has one PCI and one PCI Express™ x16 slot. The following sub-sections
describe the slots and the expansion cards that they support.
Make sure to unplug the power cord before adding or removing
expansion cards. Failure to do so may cause you physical injury and
damage the motherboard.
2.7.1 Expansion slots
PCI slot
The PCI slots support PCI cards such
as a LAN card, SCSI card, USB card,
and other cards that comply with PCI
specifications. The figure shows a
LAN card installed on a PCI slot.
PCI Express™ x16 slot
This motherboard supports PCI
Express™ x16 graphic cards
that comply with PCI Express™
specifications. The figure shows a
graphics card installed on the PCI
Express™ x16 slot.
The chassis supports PCI Express x 16 cards with 192mm x 19mm or
smaller dimensions only.
ASUS T3-P5G965
2-13
2.7.2 Expansion card installation
To install an expansion card:
1.
Before installing the expansion card, read the documentation that
came with it and make the necessary hardware settings for the card.
2.
Locate and remove one metal bracket lock screw.
3.
Remove the metal bracket lock.
4.
Align the card connector with the slot, then press firmly.
5.
Secure the card with one screw.
6.
Replace the metal braket lock, then secure it with one screw.
1
4
5
2
5
3
Standard interrupt assignments
IRQ
Standard Function
0
1
2
4
6
7*
8
9*
10*
11*
12*
13
System Timer
Keyboard Controller
Programmable Interrupt
Communications Port (COM1)
Floppy Disk Controller
Printer Port (LPT1)
System CMOS/Real Time Clock
ACPI Mode when used
IRQ Holder for PCI Steering
IRQ Holder for PCI Steering
PS/2 Compatible Mouse Port
Numeric Data Processor
14*
Primary IDE Channel
* These IRQs are usually available for ISA or PCI devices.
2-14
Chapter 2: Basic installation
IRQ assignments for this motherboard
A
PCI slot PCI Express x16 slot
Onboard USB controller 1
Onboard USB controller 2
Onboard USB controller 3
Onboard USB controller 4
Onboard USB 2.0 controller
Onboard IDE port
Onboard AC’ 97 Audio
Onboard LAN
Onboard 1394
B
C
D
E F
––
––
––
––
–– shared
shared
––
––
––
––
––
––
––
––
–– shared ––
––
shared
––
––
––
––
––
––
shared ––
––
––
––
––
–– shared ––
––
––
––
––
–– shared ––
––
––
shared ––
––
––
shared
––
––
––
––
––
––
shared
––
––
––
––
––
––
––
––
–– shared
G
H
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
––
When using a PCI card on shared slots, ensure that the drivers support
“Share IRQ” or that the cards do not need IRQ assignments; otherwise,
conflicts will arise between the two PCI groups, making the system
unstable and the card inoperable.
2.8
Installing an optical drive
The barebone system comes with a 5.25-inch drive bays for an optical
drive.
To install an optical drive:
1.
Place the chassis upright.
2.
Insert the optical drive to the
upper 5.25 in drive bay, then
carefully push the drive until its
screw holes align with the holes
on the bay.
3.
Secure the optical drive with
four screws on both sides of the
bay.
4.
Connect the IDE and the power
plugs to the connectors at the
back of the drive.
ASUS T3-P5G965
2
3
2
3
2-15
2.9
Installing a Serial ATA disk drive
The system supports one Serial ATA hard disk drive.
To install a Serial ATA hard disk drive:
1.
Connect the SATA power cable
to the plug of the power supply
unit.
2.
Connect the SATA signal cable
and the power plugs to the
connectors at the back of the
drive.
3.
Locate the HDD tray.
4.
Insert a hard disk drive (with
the HDD PCB facing the top of
the chassis) to the tray, then
secure it with four screws.
5.
Connect the SATA signal cable
to the SATA connector on the
motherboard, and tighten all the
cables with the plastic coils.
1
4
4
2
4
4
4
2-16
Chapter 2: Basic installation
2.10 Reinstalling the power supply unit
Reinstall the power supply unit (PSU) after installing the system
components and reconnecting the cables.
To reinstall the PSU:
1.
If necessary, connect the
4-pin 12V power plug to the
ATX12V connector on the
motherboard.
2.
If necessary, connect the
24-pin ATX power plug to the
ATXPWR connector on the
motherboard.
3.
Connect the optical drive
power connector.
4. Lift the PSU in the direction of
the arrow until it properly fits
in place.
5. Secure the PSU with the
screws you removed earlier.
Make sure the PSU cables do not interfere with the CPU and/or chassis
fans.
CTR
BASS
REAR
SPK
SIDE
SPK
Voltage selector
LINE
IN
FRONT
MIC IN
eSATA
The PSU has a 115 V/230 V voltage selector
switch located beside the power connector. Use
this switch to select the appropriate system
input voltage according to the voltage supply in
your area.
If the voltage supply in your area is 100‑127 V,
set the switch to 115 V.
If the voltage supply in your area is 200‑240 V,
set the switch to 230 V.
Setting the switch to 115 V in a 230 V environment will seriously
damage the system!
ASUS T3-P5G965
2-17
2.11 Replacing the cover
To replace the cover:
1.
Turn the chassis upright.
2.
Position the front edge of the
cover at least two inches from
the front panel cover. Fit the
cover tabs with the chassis rail
and the front panel tabs.
3.
Lower the rear edge of the
cover as shown.
4.
Push the cover slightly toward
the front panel until it fits in
place.
5.
Secure the cover with the three
screws you removed earlier.
3
4
2
5
2-18
Chapter 2: Basic installation
Chapter 3
Starting up
This chapter helps you power up
the system and install drivers and
utilities from the support CD.
3.1
Installing an operating system
The barebone system supports Windows® 2000/XP operating systems
(OS). Always install the latest OS version and corresponding updates so
you can maximize the features of your hardware.
Because motherboard settings and hardware options vary, use the setup
procedures presented in this chapter for general reference only. Refer to
your OS documentation for more information.
3.2
Powering up
The system power button is located on the front panel. Press the system
power button ( ) to enter the OS.
Press to enter the
system OS
In Windows® OS, pressing the button shuts down, restarts, or puts the
system in sleep mode (S3) depending on the OS setting.
3.3
Support CD information
The support CD that came with the system contains useful software and
several utility drivers that enhance the system features.
• Screen display and driver options may not be the same for other
operating system versions.
• The contents of the support CD are subject to change at any time
without notice. Visit the ASUS website for updates.
3-
Chapter 3: Starting up
3.3.1 Running the support CD
To begin using the support CD, place the CD in your optical drive. The
CD automatically displays the Drivers menu if Autorun is enabled in your
computer.
Click an item to install
Click an icon to display
other information
If Autorun is NOT enabled in your computer, browse the contents of the
support CD to locate the file ASSETUP.EXE from the BIN folder. Double-click the ASSETUP.EXE to run the CD.
3.3.2 Drivers menu
The drivers menu shows the available device drivers if the system detects
installed devices. Install the necessary drivers to activate the devices.
ASUS InstAll - Drivers Installation Wizard
Allows you to easily install all necessary drivers for your system.
Intel(R) Chipset INF Update Program
Installs the Intel® Chipset INF Update Program.
Intel(R) Graphics Accelerator Driver
Installs the Intel® graphics accelerator driver.
ASUS T3-P5G965
3-
SoundMAX ADI Audio Driver
Installs the SoundMAX® AC`97 audio driver.
Realtek RTL8111b 10/100/1000M LAN Driver
Installs the Realtek® 10/100/1000M LAN Driver.
3.3.3 Utilities menu
The Utilities menu shows the applications and other software that the
motherboard supports.
ASUS InstAll - Installation Wizard for Utilities
Allows you to easily install all bundled utilities for this motherboard.
ASUS PC Probe II
This smart utility continuously monitors vital system information such as
fan rotations, CPU temperature, and system voltages, and alerts you on
any detected problems. This utility helps you keep your computer in a
healthy operating condition.
3-
Chapter 3: Starting up
ASUS Update
Installs the ASUS Update that allows you to update the motherboard BIOS
and drivers. This utility requires an Internet connection either through a
network or an Internet Service Provider (ISP). See page 5-8 for details.
Adobe Acrobat Reader V7.0
The Acrobat® Acrobat Reader® software is for viewing files saved in
Portable Document Format (PDF).
ASUS Screensaver
Bring life to your idle screen by installing the ASUS Screensaver.
3.3.4 ASUS contact information
The Contact tab displays the ASUS contact information.
ASUS T3-P5G965
3-
3-
Chapter 3: Starting up
This chapter gives information
about the motherboard that comes
with the system. This chapter
includes the motherboard layout,
jumper settings, and connector
locations.
Motherboard info
Chapter 4
4.1
Introduction
The motherboard comes already installed in the ASUS T3-P5G965 system.
This chapter provides technical information about the motherboard for
future upgrades or system reconfiguration.
4.2
Motherboard layout
26.7cm(10.5in)
SPI_J1
CLRTC
PCI1
VT6308P
Super I/O
SB_PWR
PCIEX16
BUZZER
FRONT_CON
CR2032 3V
Lithium Cell
CMOS Power
CD
AUDIO
AD19888
RTM867N
SPDIF_OUT
SATA1
SATA2
22.4cm(8.8in)
VGA_COM
SATA3
Intel ICH 8
75
A7
LG
PRI_RAID
ESATA
JMB363
KBMS
Intel GMCH G965
KBPWR
USBPW910
EATXPWR
R
DDR DIMM_A1 (64 bit,184-pin module)
RTL8111B
F_USB34
USBPW34
USBPW12
DDR DIMM_A2 (64 bit,184-pin module)
ATX12V
DDR DIMM_B1 (64 bit,184-pin module)
DDR DIMM_B2 (64 bit,184-pin module)
4-
ADP3198
CPU_FAN
LAN_USB12
Chapter 4: Motherboard Info
4.3
Jumpers
1. Clear RTC RAM (CLRTC)
This jumper allows you to clear the Real Time Clock (RTC) RAM in
CMOS. You can clear the CMOS memory of date, time, and system
setup parameters by erasing the CMOS RTC RAM data. The onboard
button cell battery powers the RAM data in CMOS, which include
system setup information such as system passwords.
To erase the RTC RAM:
1. Turn OFF the computer and unplug the power cord.
2. Remove the onboard battery.
3. Move the jumper cap from pins 1-2 (default) to pins 2-3. Keep the
cap on pins 2-3 for about 5~10 seconds, then move the cap back
to pins 1-2.
4. Re-install the battery.
5. Plug the power cord and turn ON the computer.
6. Hold down the <Del> key during the boot process and enter BIOS
setup to re-enter data.
Except when clearing the RTC RAM, never remove the cap on CLRTC
jumper default position. Removing the cap will cause system boot failure!
CLRTC
1 2
Normal
(Default)
2 3
Clear CMOS
R
Clear RTC RAM
ASUS T3-P5G965
4-
2. USB device wake-up (3-pin USBPW12, USBPW34,
USBPW910)
Set these jumpers to +5V to wake up the computer from S1 sleep
mode (CPU stopped, DRAM refreshed, system running in low power
mode) using the connected USB devices. Set to +5VSB to wake up
from S3 and S4 sleep modes (no power to CPU, DRAM in slow refresh,
power supply in reduced power mode).
USBPW910
R
USBPW34
USBPW12
USB device Wake up
1 2
+5V
(Default)
1 2
+5V
(Default)
2 3
+5VSB
2 3
+5VSB
• The USB device wake-up feature requires a power supply that can
provide 500mA on the +5VSB lead for each USB port; otherwise, the
system would not power up.
• The total current consumed must NOT exceed the power supply
capability (+5VSB) whether under normal condition or in sleep mode.
3. Keyboard power (3-pin KBPWR)
This jumper allows you to enable or disable the keyboard wake-up
feature. Set this jumper to pins 2-3 (+5VSB) to wake up the computer
when you press a key on the keyboard (the default is the Space Bar).
This feature requires an ATX power supply that can supply at least 1A
on the +5VSB lead, and a corresponding setting in the BIOS.
KBPWR
1 2
2 3
R
+5V
(Default)
+5VSB
Keyboard Power Setting
4-
Chapter 4: Motherboard Info
4.4
Connectors
This section describes and illustrates the connectors on the motherboard.
1. CPU fan connector (4-pin CPU_FAN)
The fan connector supports the proprietary CPU fan. Connect the fan
cable to the fan connector on the motherboard, making sure that the
black wire of each cable matches the ground pin of the connector.
CPU_FAN
R
GND
CPU FAN PWR
CPU FAN PWM
CPU FAN IN
CPU Fan Connector
Do not forget to connect the fan cable to the fan connector. Insufficient
air flow within the system may damage the motherboard components.
These are not jumpers! DO NOT place jumper caps on the fan
connectors!
2. ATX power connectors (24-pin EATXPWR, 4-pin ATX12V)
These connectors are for the 24-pin and 4-pin power plugs from the
power supply unit. The plugs from the power supply unit are designed
to fit these connectors in only one orientation. Find the proper
orientation and push down firmly until the connectors completely fit.
EATXPWR
ATX12V
Ground
+5 Volts
+5 Volts
+5 Volts
-5 Volts
Ground
Ground
Ground
PSON#
Ground
-12 Volts
+3 Volts
+12V DC
GND
Do not forget to connect the 4-pin ATX12V power plug to the ATX12V
connector on the motherboard; otherwise, the system will not boot up.
ASUS T3-P5G965
+12V DC
GND
ATX Power Connector
+3 Volts
+12 Volts
+12 Volts
+5V Standby
Power OK
Ground
+5 Volts
Ground
+5 Volts
Ground
+3 Volts
+3 Volts
R
4-
3. RAID connector (40-1 pin PRI_RAID)
This connector is for an Ultra DMA 100/66 signal cable. The Ultra
DMA 100/66 signal cable has three connectors: a blue connector for
the primary RAID connector on the motherboard, a black connector
for an Ultra DMA 100/66 IDE slave device (optical drive/hard disk
drive), and a gray connector for an Ultra DMA 100/66 RAID master
device (hard disk drive). Refer to the hard disk documentation for the
jumper settings.
R
PIN 1
PRI_RAID
NOTE: Orient the red markings
(usually zigzag) on the ID
ribbon cable to PIN 1.
RAID Connector
• Pin 20 on the IDE connector is removed to match the covered hole
on the Ultra DMA cable connector. This prevents incorrect insertion
when you connect the IDE cable.
• Use the 80-conductor IDE cable for Ultra DMA 100/66 IDE devices.
4-
Chapter 4: Motherboard Info
4. Serial ATA connectors
(7-pin SATA1, SATA2, SATA3)
These connectors are for the Serial ATA signal cables for Serial ATA
hard disk drives.
SATA3
GND
RSATA_RXN2
RSATA_RXP2
GND
RSATA_TXN2
RSATA_TXP2
GND
GND
RSATA_RXN1
RSATA_RXP1
GND
RSATA_TXN1
RSATA_TXP1
GND
GND
RSATA_RXN3
RSATA_RXP3
GND
RSATA_TXN3
RSATA_TXP3
GND
R
SATA1
SATA2
SATA Connectors
When using the connectors in Standard IDE mode, connect the primary
(boot) hard disk drive to the SATA1/2 connector. Refer to the table
below for the recommended SATA hard disk drive connections.
Serial ATA hard disk drive connection
Connector
Color
Setting
Use
SATA1/2
Red
Master
Boot disk
SATA3
Red
Slave
Data Disk
right angle side
Connect the right-angle side
of SATA signal cable to SATA
device. Or you may connect
the right-angle side of SATA
cable to the onboard SATA
port to avoid mechanical
conflict with huge graphics
cards.
ASUS T3-P5G965
4-
5. Digital audio connector (4-1 pin SPDIF_OUT)
SPDIFOUT
GND
+5V
This connector is for an additional Sony/Philips Digital Interface
(S/PDIF) port(s). Connect the S/PDIF Out cable to this connector,
then connect to the S/PDIF module of the system chassis.
SPDIF_OUT
R
Digital Audio Connector
6. Optical drive audio connector (4-pin CD)
Right Audio Channel
Ground
Ground
Left Audio Channel
These connectors allow you to receive stereo audio input from sound
sources such as a CD-ROM, TV tuner, or MPEG card.
R
Internal Audio Connector
4-
CD
(black)
Chapter 4: Motherboard Info
Chapter 5
BIOS setup
This chapter tells how to change
system settings through the BIOS
Setup menus and describes the
BIOS parameters.
5.1
Managing and updating your BIOS
The following utilities allow you to manage and update the motherboard
Basic Input/Output System (BIOS) setup.
1.
ASUS EZ Flash 2 (Updates the BIOS using a floppy disk, USB Flash, or
the motherboard support CD during POST.)
2.
ASUS AFUDOS (Updates the BIOS using a bootable floppy disk in DOS
mode.)
3.
ASUS CrashFree BIOS 2 (Updates the BIOS using a bootable floppy
disk or the motherboard support CD when the BIOS file fails or gets
corrupted.)
4.
ASUS Update (Updates the BIOS in Windows® environment.)
Refer to the corresponding sections for details on these utilities.
Save a copy of the original motherboard BIOS file to a bootable floppy
disk in case you need to restore the BIOS in the future. Copy the original
motherboard BIOS using the ASUS Update or AFUDOS utilities.
5-
Chapter 5: BIOS setup
5.1.1 ASUS EZ Flash 2 utility
The ASUS EZ Flash 2 feature allows you to update the BIOS without having
to go through the long process of booting from a floppy disk and using
a DOS‑based utility. The EZ Flash 2 utility is built-in the BIOS chip so it is
accessible by pressing <Alt> + <F2> during the Power-On Self-Test (POST).
To update the BIOS using EZ Flash 2:
1.
Visit the ASUS website (www.asus.com) to download the latest BIOS
file for the motherboard.
2.
Save the BIOS file to a floppy disk or a USB flash disk, then restart the
system.
3.
You can launch the EZ Flash 2 by two methods.
(1) Insert the floppy disk / USB flash disk that contains the BIOS file
to the floppy disk drive or the USB port.
Press <Alt> + <F2> during POST to display the following.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.00
FLASH TYPE: MXIC 25L8005
Current ROM
BOARD: P5B-BN T3-P5G965
VER: 0403
DATE: 10/16/06
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
A:
Note
[Enter] Select or Load
[B] Backup
[Tab] Switch
[Up/Down/Home/End] Move
[ESC] Exit
(2) Enter BIOS setup program. Go to the Tools menu to select EZ
Flash 2 and press <Enter> to enable it.
4.
You can switch between drives by pressing <Tab> before the
correct file is found. Then press <Enter>.
When the correct BIOS file is found, EZ Flash 2 performs the BIOS
update process and automatically reboots the system when done.
• This function can support devices such as USB flash disk, or floppy
disk with FAT 32/16 format only.
• Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
ASUS T3-P5G965
5-
5.1.2 AFUDOS utility
The AFUDOS utility allows you to update the BIOS file in DOS environment
using a bootable floppy disk with the updated BIOS file. This utility also
allows you to copy the current BIOS file that you can use as backup when
the BIOS fails or gets corrupted during the updating process.
Copying the current BIOS
To copy the current BIOS file using the AFUDOS utility:
• Make sure that the floppy disk is not write-protected and has at
least 600 KB free space to save the file.
• The succeeding BIOS screens are for reference only. The actual BIOS
screen displays may not be exactly the same as shown.
1.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
2.
Boot the system in DOS mode, then at the prompt type:
afudos /o[filename]
where the [filename] is any user-assigned filename not more than
eight alphanumeric characters for the main filename and three
alphanumeric characters for the extension name.
A:\>afudos /oOLDBIOS1.ROM
Main filename
3.
Extension name
Press <Enter>. The utility copies the current BIOS file to the floppy
disk.
A:\>afudos /oOLDBIOS1.ROM
AMI Firmware Update Utility - Version 1.10
Copyright (C) 2002 American Megatrends, Inc. All rights reserved.
Reading flash ..... done
A:\>
The utility returns to the DOS prompt after copying the current BIOS
file.
5-
Chapter 5: BIOS setup
Updating the BIOS file
To update the BIOS file using the AFUDOS utility:
1.
Visit the ASUS website (www.asus.com) and download the latest BIOS
file for the motherboard. Save the BIOS file to a bootable floppy disk.
Write the BIOS filename on a piece of paper. You need to type the exact
BIOS filename at the DOS prompt.
2.
Copy the AFUDOS utility (afudos.exe) from the motherboard support
CD to the bootable floppy disk you created earlier.
3.
Boot the system in DOS mode, then at the prompt type:
afudos /i[filename]
where [filename] is the latest or the original BIOS file on the bootable
floppy disk.
A:\>afudos /iP5BBN.ROM
4.
The utility reads the file and starts updating the BIOS.
A:\>afudos /iP5BBN.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Search bootblock version
Advance Check........
Erasing flash .... done
Writing flash .... 0x0008CC00 (9%)
Do not shut down or reset the system while updating the BIOS to
prevent system boot failure!
ASUS T3-P5G965
5-
5.
The utility returns to the DOS prompt after the BIOS update process is
completed. Reboot the system from the hard disk drive.
A:\>afudos /iP5BBN.ROM
AMI Firmware Update Utility - Version 1.19(ASUS V2.07(03.11.24BB))
Copyright (C) 2003 American Megatrends, Inc. All rights reserved.
WARNING!! Do not turn off power during flash BIOS
Reading file ..... done
Reading flash .... done
Search bootblock version
Advance Check.........
Erasing flash ..... done
Writing flash ..... done
Verifying flash ... done
Please restart your computer
A:\>
5.1.3 ASUS CrashFree BIOS 2 utility
The ASUS CrashFree BIOS 2 is an auto recovery tool that allows you to
restore the BIOS file when it fails or gets corrupted during the updating
process. You can update a corrupted BIOS file using the motherboard
support CD or the floppy disk that contains the updated BIOS file.
• Prepare the motherboard support CD or the floppy disk containing
the updated motherboard BIOS before using this utility.
• Make sure that you rename the original or updated BIOS file in the
floppy disk to P5BBN.ROM.
Recovering the BIOS from a floppy disk
To recover the BIOS from a floppy disk:
5-
1.
Turn on the system.
2.
Insert the floppy disk with the original or updated BIOS file to the
floppy disk drive.
Chapter 5: BIOS setup
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When found, the utility reads the BIOS file and starts flashing the
corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy found!
Reading file “P5BBN.ROM”. Completed.
Start flashing...
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
Recovering the BIOS from the support CD
To recover the BIOS from the support CD:
1.
Remove any floppy disk from the floppy disk drive, then turn on the
system.
2.
Insert the support CD to the optical drive.
3.
The utility displays the following message and automatically checks
the floppy disk for the original or updated BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
When no floppy disk is found, the utility automatically checks the
optical drive for the original or updated BIOS file. The utility then
updates the corrupted BIOS file.
Bad BIOS checksum. Starting BIOS recovery...
Checking for floppy...
Floppy not found!
Checking for CD-ROM...
CD-ROM found!
Reading file “P5BBN.ROM”. Completed.
Start flashing...
ASUS T3-P5G965
5-
DO NOT shut down or reset the system while updating the BIOS! Doing
so can cause system boot failure!
4.
Restart the system after the utility completes the updating process.
The recovered BIOS may not be the latest BIOS version for this
motherboard. Visit the ASUS website (www.asus.com) to download the
latest BIOS file.
5.1.4 ASUS Update utility
The ASUS Update is a utility that allows you to manage, save, and update
the motherboard BIOS in Windows® environment. The ASUS Update utility
allows you to:
•
Save the current BIOS file
•
Download the latest BIOS file from the Internet
•
Update the BIOS from an updated BIOS file
•
Update the BIOS directly from the Internet, and
•
View the BIOS version information.
This utility is available in the support CD that comes with the motherboard
package.
ASUS Update requires an Internet connection either through a network
or an Internet Service Provider (ISP).
Installing ASUS Update
To install ASUS Update:
1.
Place the support CD in the optical drive. The Drivers menu appears.
2.
Click the Utilities tab, then click ASUS Update. See page 3-4 for the
Utilities screen menu.
3.
The ASUS Update utility is copied to your system.
Quit all Windows® applications before you update the BIOS using this
utility.
5-
Chapter 5: BIOS setup
Updating the BIOS through the Internet
To update the BIOS through the Internet:
1.
Launch the ASUS Update utility from the Windows® desktop by clicking
Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The ASUS
Update main window appears.
2.
Select Update BIOS from
the Internet option from the
drop‑down menu, then click
Next.
ASUS T3-P5G965
3.
Select the ASUS FTP site
nearest you to avoid network
traffic, or click Auto Select.
Click Next.
5-
4.
From the FTP site, select the
BIOS version that you wish to
download. Click Next.
5.
Follow the screen instructions to
complete the update process.
The ASUS Update utility is
capable of updating itself
through the Internet. Always
update the utility to avail all
its features.
Updating the BIOS through a BIOS file
To update the BIOS through a BIOS file:
5-10
1.
Launch the ASUS Update utility from the Windows® desktop by
clicking Start > Programs > ASUS > ASUSUpdate > ASUSUpdate. The
ASUS Update main window appears.
2.
Select Update BIOS from a file
option from the drop‑down menu,
then click Next.
3.
Locate the BIOS file from the
Open window, then click Open.
4.
Follow the screen instructions to
complete the update process.
Chapter 5: BIOS setup
5.2
BIOS setup program
This motherboard supports a programmable Low-Pin Count (LPC) chip
that you can update using the provided utility described in section “4.1
Managing and updating your BIOS.”
Use the BIOS Setup program when you are installing a motherboard,
reconfiguring your system, or prompted to“Run Setup.” This section
explains how to configure your system using this utility.
Even if you are not prompted to use the Setup program, you can change
the configuration of your computer in the future. For example, you can
enable the security password feature or change the power management
settings. This requires you to reconfigure your system using the BIOS Setup
program so that the computer can recognize these changes and record
them in the CMOS RAM of the LPC chip.
The LPC chip on the motherboard stores the Setup utility. When you start
up the computer, the system provides you with the opportunity to run this
program. Press <Del> during the Power-On Self-Test (POST) to enter the
Setup utility; otherwise, POST continues with its test routines.
If you wish to enter Setup after POST, reboot the system by doing any of
the following procedures:
• Restart using the OS standard shut-down procedure.
• Press <Ctrl>+<Alt>+<Del> simultaneously.
• Press the reset button on the system chassis.
• Press the power button to turn the system off then back on.
Using the power button, reset button, or the <Ctrl>+<Alt>+<Del> keys
to force reset from a running operating system can cause damage to
your data or system. We recommend to always shut-down the system
properly from the operating system.
The Setup program is designed to make it as easy to use as possible. Being
a menu-driven program, it lets you scroll through the various sub-menus
and make your selections from the available options using the navigation
keys.
• The default BIOS settings for this motherboard apply for most
conditions to ensure optimum performance. If the system becomes
unstable after changing any BIOS settings, load the default settings
to ensure system compatibility and stability. Select the Load Default
Settings item under the Exit Menu. See section “5.8 Exit Menu.”
• The BIOS setup screens shown in this section are for reference
purposes only, and may not exactly match what you see on your
screen.
• Visit the ASUS website (www.asus.com) to download the latest BIOS
file for this motherboard.
ASUS T3-P5G965
5-11
5.2.1 BIOS menu screen
Menu items
Menu bar
Configuration fields
System Time
System Date
SATA 1
SATA 2
SATA 3
[11:51:19]
[Mon 05/15/2006]
:[Not Detected]
:[Not Detected]
:[Not Detected]
General help
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Use [+] or [-] to
configure the System
time.
IDE Configuration
System Information
Sub-menu items
Navigation keys
5.2.2 Menu bar
The menu bar on top of the screen has the following main items:
Main
For changing the basic system configuration
Advanced
For changing the advanced system settings
Power
For changing the advanced power management (APM)
configuration
Boot
For changing the system boot configuration
Tools
For setting EZ Flash 2 and O.C. Profile.
Exit
For selecting the exit options and loading default settings
To select an item on the menu bar, press the right or left arrow key on the
keyboard until the desired item is highlighted.
5.2.3 Navigation keys
At the bottom right corner of a menu screen are the navigation keys for
that particular menu. Use the navigation keys to select items in the menu
and change the settings.
Some of the navigation keys differ from one screen to another.
5-12
Chapter 5: BIOS setup
5.2.4 Menu items
The highlighted item on the menu
bar displays the specific items for
that menu. For example, selecting
Main shows the Main menu items.
The other items (Advanced, Power,
Boot, Tools and Exit) on the menu
bar have their respective menu
items.
System Time [16:37:21]
System Date [Wed,10/20/2004]
Legacy Diskette A [1.44M, 3.5 in]
Primary IDE Master :[ST320410A]
Primary IDE Slave :[ASUS CD-S520/A]
Third IDE Master
:[Not Detected]
Third IDE Slave
:[Not Detected]
Fourth IDE Master :[Not Detected]
Fourth IDE Slave :[Not Detected]
IDE Configuration
System Information
Main menu items
5.2.5 Sub-menu items
A solid triangle before each item on any menu screen means that the
item has a sub-menu. To display the sub-menu, select the item and press
<Enter>.
5.2.6 Configuration fields
These fields show the values for the menu items. If an item is user-configurable, you can change the value of the field opposite the item.
You cannot select an item that is not user-configurable.
A configurable field is enclosed in brackets, and is highlighted when
selected. To change the value of a field, select it then press <Enter> to
display a list of options. Refer to “5.2.7 Pop-up window.”
5.2.7 Pop-up window
Select a menu item then press <Enter> to display a pop-up window with
the configuration options for that item.
5.2.8 Scroll bar
A scroll bar appears on the right side
of a menu screen when there are
items that do not fit on the screen.
Press the Up/Down arrow keys or
<Page Up> /<Page Down> keys
to display the other items on the
screen.
5.2.9 General help
At the top right corner of the menu
screen is a brief description of the
selected item.
ASUS T3-P5G965
Advanced PCI/PnP Settings
WARNING: Setting wrong values in
below sections may cause system to
malfunction.
Plug And Play O/S [No]
PCI Latency Timer [64]
Allocate IRQ to PCI VGA[Yes]
Palette Snooping
Pop-up window
Scroll bar
5-13
5.3
Main menu
When you enter the BIOS Setup program, the Main menu screen appears,
giving you an overview of the basic system information.
Refer to section “5.2.1 BIOS menu screen” for information on the menu
screen items and how to navigate through them.
System Time [16:37:21]
System Date [Wed,10/20/2004]
SATA 1
SATA 2
SATA 3
:[Not Detected]
:[Not Detected]
:[Not Detected]
Use [ENTER], [TAB] or
[SHIFT-TAB] to select
a field.
Use [+] or [-] to
configure the System
time.
IDE Configuration
System Information
5.3.1 System Time [xx:xx:xx]
Allows you to set the system time.
5.3.2 System Date [Day xx/xx/xxxx]
Allows you to set the system date.
5-14
Chapter 5: BIOS setup
5.3.3 SATA1, SATA2, and SATA3
While entering Setup, the BIOS automatically detects the presence of IDE
devices. There is a separate sub-menu for each IDE device. Select a device
item then press <Enter> to display the IDE device information.
SATA 1
Device
: Not Detected
Type
[Auto]
LBA/Large Mode
[Auto]
Block(Multi-sector Transfer) M
[Auto]
PIO Mode
[Auto]
DMA Mode
[Auto]
Smart Monitoring
[Auto]
32Bit Data Transfer
[Enabled]
The BIOS automatically detects the values opposite the dimmed items
(Device, Vendor, Size, LBA Mode, Block Mode, PIO Mode, Async DMA, Ultra
DMA, and SMART monitoring). These values are not user-configurable.
These items show N/A if no IDE device is installed in the system.
Type [Auto]
Selects the type of IDE drive. Setting to Auto allows automatic selection
of the appropriate IDE device type. Select CDROM if you are specifically
configuring a CD-ROM drive. Select ARMD (ATAPI Removable Media Device)
if your device is either a ZIP, LS-120, or MO drive. Configuration options:
[Not Installed] [Auto] [CDROM] [ARMD]
LBA/Large Mode [Auto]
Enables or disables the LBA mode. Setting to Auto enables the LBA mode
if the device supports this mode, and if the device was not previously
formatted with LBA mode disabled. Configuration options: [Disabled]
[Auto]
Block (Multi-sector Transfer) M [Auto]
Enables or disables data multi-sectors transfers. When set to Auto, the
data transfer from and to the device occurs multiple sectors at a time if
the device supports multi-sector transfer feature. When set to [Disabled],
the data transfer from and to the device occurs one sector at a time.
Configuration options: [Disabled] [Auto]
ASUS T3-P5G965
5-15
PIO Mode [Auto]
Selects the PIO mode.
Configuration options: [Auto] [0] [1] [2] [3] [4]
DMA Mode [Auto]
Selects the DMA mode. Configuration options: [Auto] [SWDMA0]
[SWDMA1] [SWDMA2] [MWDMA0] [MWDMA1] [MWDMA2] [UDMA0]
[UDMA1] [UDMA2] [UDMA3] [UDMA4] [UDMA5]
SMART Monitoring [Auto]
Sets the Smart Monitoring, Analysis, and Reporting Technology.
Configuration options: [Auto] [Disabled] [Enabled]
32Bit Data Transfer [Enabled]
Enables or disables 32-bit data transfer.
Configuration options: [Disabled] [Enabled]
5.3.4 IDE Configuration
The items in this menu allow you to set or change the configurations for
the IDE devices installed in the system. Select an item then press <Enter>
if you want to configure the item.
IDE Configuration
SATA Configuration [Enhanced]
Hard Disk Write Protect [Disabled]
IDE Detect Time Out (Sec) [35]
When in AHCI/RAID
mode, SATA controller
is forced to Native
mode.
SATA Configuration [Enhanced]
Configuration options: [Compatible] [Enhanced] [Disabled]
Configure SATA as [IDE]
Configuration options: [IDE] [AHCI]
Hard Disk Write Protect [Disabled]
Allows you to enable to disable the hard disk write protection. This will be
effective only if device is accessed through BIOS. Configuration options:
[Disabled] [Enabled]
IDE Detect Time Out [35]
Selects the time out value for detecting ATA/ATAPI devices.
Configuration options: [0] [5] [10] [15] [20] [25] [30] [35]
5-16
Chapter 5: BIOS setup
5.3.5 System Information
This menu gives you an overview of the general system specifications. The
BIOS automatically detects the items in this menu.
AMIBIOS
Version
: 0403
Build Date : 10/16/06
Processor
Type
Speed
Count
: Genuine Intel(R) CPU 3.80 GHz
: 3800 MHz
: 1
System Memory
Available
:504 MB
AMI BIOS
Displays the auto-detected BIOS information.
Processor
Displays the auto-detected CPU specification.
System Memory
Displays the auto-detected system memory.
5.4
Advanced menu
The Advanced menu items allow you to change the settings for the CPU
and other system devices.
Take caution when changing the settings of the Advanced menu items.
Incorrect field values can cause the system to malfunction.
USB Configuration
CPU Configuration
Chipset
Onboard Devices Configuration
PCIPnP
ASUS T3-P5G965
Configure the USB
support
5-17
5.4.1 USB Configuration
The items in this menu allow you to change the USB-related features.
Select an item then press <Enter> to display the configuration options.
USB Configuration
Module Version - 2.24.0-11.4
USB Devices Enabled:
None
USB 1.1 Controller [Enabled]
USB 2.0 Controller [Enabled]
Legacy USB Support [Enabled]
USB 2.0 Controller Mode [HiSpeed]
BIOS EHCI Hand-off [Enabled]
The Module Version and USB Devices Enabled items show the
auto-detected values. If no USB device is detected, the item shows
None.
USB 1.1 Controller [Enabled]
Allows you to enable or disable the USB 1.1 controller.
Configuration options: [Enabled] [Disabled]
USB 2.0 Controller [Enabled]
Allows you to enable or disable the USB 2.0 controller.
Configuration options: [Enabled] [Disabled]
Legacy USB Support [Enabled]
Allows you to enable or disable support for USB devices on legacy
operating systems (OS). Setting to Auto allows the system to detect the
presence of USB devices at startup. If detected, the USB controller legacy
mode is enabled. If no USB device is detected, the legacy USB support is
disabled. Configuration options: [Disabled] [Enabled] [Auto]
USB 2.0 Controller Mode [HiSpeed]
Allows you to set the USB 2.0 controller mode to HiSpeed (480 Mbps) or
FullSpeed (12 Mbps). Configuration options: [FullSpeed ] [HiSpeed ]
BIOS EHCI Hand-off [Enabled]
Allows you to enable or disable the enhanced host controller interface
(EHCI) hand-off support. This is a workaround for operating systems
without EHCI hand-off support. The ECHI ownership change should be
claimed by the EHCI driver. Configuration options: [Disabled] [Enabled]
5-18
Chapter 5: BIOS setup
5.4.2 CPU Configuration
The items in this menu show the CPU-related information that the BIOS
automatically detects.
Configure advanced CPU settings
Module Version: 3C.0E
Manufacturer: Intel
Brand String: Genuine Intel(R) CPU 3.80GHz
Frequency
: 3.80GHz
FSB Speed
: 800MHz
Cache L1
: 16 KB
Cache L2
: 2048 KB
Ratio Status: Unlocked (Max:19, Min:14)
Ratio Actual Value: 14
CPUID
: F43
CPU ratio adjustment [Auto]
C1E Support [Enabled]
Max CPUID Value Limit: [Disabled]
CPU TM function [Enabled]
Execute Disable Bit [Enabled]
Hyper Threading Technology [Enabled]
Intel(R) SpeedStep(tm) tech. [Automatic]
CPU ratio adjustment [Auto]
Sets the ratio between the CPU Core Clock and the Front Side Bus
frequency. The default value of this item is auto-detected by BIOS. Use the
<+> or <-> keys to adjust the values.
C1E Support [Enabled]
Allows you to enable or disable the C1E support. In C1E mode, the CPU
power consumption is lower than idle. Configuration options: [Disabled]
[Enabled]
Max CPUID Value Limit [Disabled]
Enable this item to boot legacy operating systems that cannot support
CPUs with extended CPUID functions. Configuration options: [Disabled]
[Enabled]
CPU TM function [Enabled]
Allows you to enable or disable the CPU internal thermal control function.
In TM mode, the CPU power consumption is reduced. Configuration options:
[Disabled] [Enabled]
Execute Disable Function [Enabled]
Allows you to enable or disable Execute Disable Function.
Configuration options: [Disabled] [Enabled]
ASUS T3-P5G965
5-19
Hyper Threading Technology [Enabled]
Enables or disables the processor Hyper-Threading Technology.
Configuration options: [Disabled] [Enabled]
Intel(R) SpeedStep(tm) Technology [Automatic]
Allows you to use the Enhanced Intel® SpeedStep® Technology. When set
to [Enabled], you can adjust the system power settings in the operating
system to use the EIST feature. Set this item to [Disabled] if you do not
want to use the EIST. Configuration options: [Automatic] [Disabled]
5.4.3 Chipset
The Chipset menu allows you to change the advanced chipset settings.
Select an item then press <Enter> to display the sub-menu.
Chipset Settings
WARNING: Setting wrong values in below sections
may cause the system to malfunction.
North Bridge Configuration
South Bridge Configuration
North Bridge Configuration
North Bridge Chipset Configuration
Memory Remap Feature [Enabled]
Configure DRAM Timing by SPD [Enabled]
Initiate Graphic Adapter [PEG/IGD]
Initiate Graphics Mode Select [Enabled,8MB]
PEG Port Configuration
PEG Force x1 [Disabled]
DVMT Function
Fixed Graphic Memory Size [128MB]
DVMT Graphic Memory Size [128MB]
5-20
Chapter 5: BIOS setup
Memory Remap Feature [Enabled]
Allows you to enable or disable Memory Remap Feature.
Configuration options: [Disabled] [Enabled]
Configure DRAM Timing by SPD [Enabled]
Allows you to Configure DRAM Timing by SPD.
Configuration options: [Disabled] [Enabled]
Initiate Graphic Adapter [PEG/IGD]
Allows you to select Initiate Graphic Adapter.
Configuration options: [IGD] [PCI/IGD] [PCI/PEG] [PEG/IGD] [PEG/PCI]
Initiate Graphics Mode Select [Enabled,8MB]
Allows you to select the amount of system memory used by the Internal
graphics device.
Configuration options: [Disabled] [Enabled,1MB] [Enabled,8MB]
PEG Force x1 [Disabled]
Allows you to set PEG Force x1 configuration.
Configuration options: [Disabled] [Enabled]
Fixed Graphic Memory Size [128MB]
Allows you to select the size of graphic memory used by fixed mode.
Configuration options: [0MB] [64MB] [128MB]
DVMT Graphic Memory Size [128MB]
Allows you to select the size of graphic memory used by DVMT mode.
Configuration options: [0MB] [64MB] [128MB] [224MB]
ASUS T3-P5G965
5-21
South Bridge Configuration
South Bridge Chipset Configuration
HD Audio Controller [Enabled]
CPU Throttling Duty [Disable]
HD Audio Controller [Enabled]
Allows you to enable or disable high definition audio controller.
Configuration options: [Disabled] [Enabled]
CPU Throttling Duty [Disable]
Allows you to configure CPU Throttling Duty.
Configuration options: [Disable] [25%] [50%] [70%]
5.4.4 Onboard Devices Configuration
Configure Onboard Device Control
Onboard 1394 Controller [Enabled]
Onboard PCIE LAN [Enabled]
LAN Option ROM [Disabled]
JMicron SATA/PATA Controller [Enabled]
Enable or disable
Configure DRAM Timing
by SPD.
Serial Port1 Address [3F8/IRQ4]
Onboard 1394 Controller [Enabled]
Enables or disables the onboard IEEE 1394a controller.
Configuration options: [Enabled] [Disabled]
5-22
Chapter 5: BIOS setup
OnBoard PCIE LAN [Enabled]
Allows you to enable or disable the onboard PCI Express LAN controller.
Configuration options: [Enabled] [Disabled]
LAN Option ROM [Disabled]
Allows you to enable or disable the option ROM in the onboard PCI
Express Gigabit LAN controller. This item appears only when the
Onboard PCIEX GbE LAN item is set to Enabled.
Configuration options: [Disabled] [Enabled]
JMicron SATA/PATA Controller [Enabled]
Allows you to enable or disable the JMicron SATA/PATA controller. Configuration options: [Disabled] [Enabled]
Serial Port1 Address [3F8/IRQ4]
Allows you to select the Serial Port1 base address.
Configuration options: [Disabled] [3F8/IRQ4] [2F8/IRQ3] [3E8/IRQ4]
[2E8/IRQ3]
5.4.5 PCI PnP
The PCI PnP menu items allow you to change the advanced settings for
PCI/PnP devices. The menu includes setting IRQ and DMA channel resources
for either PCI/PnP or legacy ISA devices, and setting the memory size block
for legacy ISA devices.
Take caution when changing the settings of the PCI PnP menu items.
Incorrect field values can cause the system to malfunction.
Advanced PCI/PnP Settings
WARNING: Setting wrong values in below sections
may cause system to malfunction.
Plug And Play O/S [No]
PCI Latency Timer [64]
Allocate IRQ to PCI VGA [Yes]
Palette Snooping [Disabled]
IRQ-3 assigned to [PCI
IRQ-4 assigned to [PCI
IRQ-5 assigned to [PCI
IRQ-7 assigned to [PCI
IRQ-9 assigned to [PCI
IRQ-10 assigned to [PCI
IRQ-11 assigned to [PCI
IRQ-14 assigned to [PCI
IRQ-15 assigned to [PCI
ASUS T3-P5G965
Device]
Device]
Device]
Device]
Device]
Device]
Device]
Device]
Device]
5-23
Plug and Play O/S [No]
When set to [No], BIOS configures all the devices in the system. When set
to [Yes] and if you install a Plug and Play operating system, the operating
system configures the Plug and Play devices not required for boot.
Configuration options: [No] [Yes]
PCI Latency Timer [64]
Allows you to select the value in units of PCI clocks for the PCI device
latency timer register. Configuration options: [32] [64] [96] [128] [160]
[192] [224] [248]
Allocate IRQ to PCI VGA [Yes]
When set to [Yes], BIOS assigns an IRQ to PCI VGA card if the card
requests for an IRQ. When set to [No], BIOS does not assign an IRQ to the
PCI VGA card even if requested. Configuration options: [Yes] [No]
Palette Snooping [Disabled]
When set to [Enabled], the palette snooping feature informs the PCI
devices that an ISA graphics device is installed in the system so that the
latter can function correctly. Configuration options: [Disabled] [Enabled]
IRQ-XX assigned to [PCI Device]
When set to [PCI Device], the specific IRQ is free for use of PCI/PnP
devices. When set to [Reserved], the IRQ is reserved for legacy ISA
devices. Configuration options: [PCI Device] [Reserved]
5-24
Chapter 5: BIOS setup
5.5
Power menu
The Power menu items allow you to change the settings for the ACPI and
Advanced Power Management (APM). Select an item then press <Enter> to
display the configuration options.
Suspend Mode [Auto]
Repost Video on S3 Resume [Disabled]
ACPI 2.0 Support [Disabled]
ACPI APIC Support [Enabled]
APM Configuration
Hardware Monitor
5.5.1 Suspend Mode [Auto]
Allows you to select the Advanced Configuration and Power Interface
(ACPI) state to be used for system suspend.
Configuration options: [S1 (POS) Only] [S3 Only] [Auto]
5.5.2 Repost Video on S3 Resume [Disabled]
Allows you to determines whether to invoke VGA BIOS POST on S3/STR
resume. Configuration options: [Disabled] [Enabled]
5.5.3 ACPI 2.0 Support [Disabled]
Allows you to add more tables for Advanced Configuration and Power
Interface (ACPI) 2.0 specifications.
Configuration options: [Disabled] [Enabled]
5.5.4 ACPI APIC Support [Enabled]
Allows you to enable or disable the Advanced Configuration and Power
Interface (ACPI) support in the Advanced Programmable Interrupt Controller
(APIC). When set to Enabled, the ACPI APIC table pointer is included in the
RSDT pointer list. Configuration options: [Disabled] [Enabled]
ASUS T3-P5G965
5-25
5.5.5 APM Configuration
APM Configuration
Restore on AC Power Loss [Power Off]
Power On By RTC Alarm [Disabled]
Power On By External Modems [Disabled]
Power On By PCI Devices [Disabled]
Power On By PCIE Devices [Disabled]
Power On By PS/2 Keyboard [Disabled]
Power On By PS/2 Mouse [Disabled]
Restore on AC Power Loss [Power Off]
When set to Power Off, the system goes into off state after an AC power
loss. When set to Power On, the system goes on after an AC power loss.
When set to Last State, the system goes into either off or on state,
whatever the system state was before the AC power loss.
Configuration options: [Power Off] [Power On] [Last State]
Power On By RTC Alarm [Disabled]
Allows you to enable or disable RTC to generate a wake event. When this
item is set to Enabled, the items RTC Alarm Date, RTC Alarm Hour, RTC
Alarm Minute, and RTC Alarm Second appear with set values. Configuration
options: [Disabled] [Enabled]
Power On By External Modems [Disabled]
This allows either settings of [Enabled] or [Disabled] for powering up the
computer when the external modem receives a call while the computer is in
Soft-off mode. Configuration options: [Disabled] [Enabled]
Power On By PCIE Devices [Disabled]
When set to [Enabled], this parameter allows you to turn on the system
through a PCI LAN, modem card, or PCI Express device. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
Power On By PCIE Devices [Disabled]
When set to [Enabled], this parameter allows you to turn on the system
through a PCI LAN, modem card, or PCI Express device. This feature
requires an ATX power supply that provides at least 1A on the +5VSB lead.
Configuration options: [Disabled] [Enabled]
5-26
Chapter 5: BIOS setup
The computer cannot receive or transmit data until the computer and
applications are fully running. Thus, connection cannot be made on the
first try. Turning an external modem off and then back on while the
computer is off causes an initialization string that turns the system on.
Power On By PS/2 Keyboard [Disabled]
Allows you to use specific keys on the keyboard to turn on the system.
This feature requires an ATX power supply that provides at least 1A on
the +5VSB lead. Configuration options: [Disabled] [Space Bar] [Ctrl-Esc]
[Power Key]
Power On By PS/2 Mouse [Disabled]
When set to [Enabled], this parameter allows you to use the PS/2 mouse
to turn on the system. This feature requires an ATX power supply that
provides at least 1A on the +5VSB lead. Configuration options: [Disabled]
[Enabled]
5.5.6 Hardware Monitor
Hardware Monitor
CPU Temperature
CPU Temperature [51ºC/122.5ºF]
MB Temperature [41ºC/105.5ºF]
CPU Fan Speed [N/A]
VCORE Voltage [ 1.280V]
3.3V Voltage [ 3.276V]
5V Voltage [ 5.120V]
12V Voltage [12.038V]
Q-Fan Control [Enabled]
CPU Temperature [xxxºC/xxxºF]
MB Temperature [xxxºC/xxxºF]
The onboard hardware monitor automatically detects and displays the
motherboard and CPU temperatures. Select Disabled if you do not wish to
display the detected temperatures.
CPU Fan Speed [xxxxRPM], [N/A], or [Ignored]
The onboard hardware monitor automatically detects and displays the CPU
fan speed in rotations per minute (RPM). If the fan is not connected to the
motherboard, the field shows N/A.
ASUS T3-P5G965
5-27
VCORE Voltage, 3.3V Voltage, 5V Voltage, 12V Voltage
The onboard hardware monitor automatically detects the voltage output
through the onboard voltage regulators.
CPU Q-Fan Control [Enabled]
Allows you to enable or disable the ASUS Q-Fan feature that smartly
adjusts the fan speeds for more efficient system operation. When this
field is set to [Enabled], the three succeeding items appear. Configuration
options: [Disabled] [Enabled]
5.6
Boot menu
The Boot menu items allow you to change the system boot options. Select
an item then press <Enter> to display the sub-menu.
Boot Settings
Boot Device Priority
Boot Settings Configuration
Security
5.6.1 Boot Device Priority
Boot Device Priority
1st Boot Device [Removable Dev.]
2nd Boot Device [Hard Drive]
3rd Boot Device [ATAPI CD-ROM]
1st ~ xxth Boot Device
These items specify the boot device priority sequence from the available
devices. The number of device items that appears on the screen depends
on the number of devices installed in the system.
Configuration options: [Removable Dev.] [Hard Drive] [ATAPI CD-ROM]
[Disabled]
5-28
Chapter 5: BIOS setup
5.6.2 Boot Settings Configuration
Boot Settings Configuration
Quick Boot [Enabled]
Full Screen Logo [Enabled]
AddOn ROM Display Mode [Force BIOS]
Bootup Num-Lock [On]
PS/2 Mouse Support [Auto]
Wait For ‘F1’ If Error [Enabled]
Hit ‘DEL’ Message Display [Enabled]
Interrupt 19 Capture [Disabled]
Allows BIOS to skip
certain tests while
booting. This will
decrease the time
needed to boot the
system.
Quick Boot [Enabled]
Enabling this item allows the BIOS to skip some power on self tests (POST)
while booting to decrease the time needed to boot the system. When set
to [Disabled], BIOS performs all the POST items.
Configuration options: [Disabled] [Enabled]
Full Screen Logo [Enabled]
This allows you to enable or disable the full screen logo display feature.
Configuration options: [Disabled] [Enabled]
Set this item to [Enabled] to use the ASUS MyLogo2™ feature.
Add On ROM Display Mode [Force BIOS]
Sets the display mode for option ROM.
Configuration options: [Force BIOS] [Keep Current]
Bootup Num-Lock [On]
Allows you to select the power-on state for the NumLock.
Configuration options: [Off] [On]
PS/2 Mouse Support [Auto]
Allows you to enable or disable support for PS/2 mouse.
Configuration options: [Disabled] [Enabled] [Auto]
Wait for ‘F1’ If Error [Enabled]
When set to Enabled, the system waits for the F1 key to be pressed when
error occurs. Configuration options: [Disabled] [Enabled]
ASUS T3-P5G965
5-29
Hit ‘DEL’ Message Display [Enabled]
When set to Enabled, the system displays the message “Press DEL to run
Setup” during POST. Configuration options: [Disabled] [Enabled]
Interrupt 19 Capture [Disabled]
When set to [Enabled], this function allows the option ROMs to trap
Interrupt 19. Configuration options: [Disabled] [Enabled]
5.6.3 Security
The Security menu items allow you to change the system security settings.
Select an item then press <Enter> to display the configuration options.
Security Settings
Supervisor Password
User Password
: Not Installed
: Not Installed
<Enter> to change
password.
<Enter> again to
disabled password.
Change Supervisor Password
Change User Password
Change Supervisor Password
Select this item to set or change the supervisor password. The Supervisor
Password item on top of the screen shows the default Not Installed. After
you set a password, this item shows Installed.
To set a Supervisor Password:
1.
Select the Change Supervisor Password item and press <Enter>.
2.
From the password box, type a password composed of at least six
letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you successfully set your
password.
To change the supervisor password, follow the same steps as in setting a
user password.
To clear the supervisor password, select the Change Supervisor Password
then press <Enter>. The message “Password Uninstalled” appears.
5-30
Chapter 5: BIOS setup
If you forget your BIOS password, you can clear it by erasing the CMOS
Real Time Clock (RTC) RAM. See section “4.3 Jumpers” for information
on how to erase the RTC RAM.
After you have set a supervisor password, the other items appear to allow
you to change other security settings.
Security Settings
Supervisor Password
User Password
: Installed
: Not Installed
<Enter> to change
password.
<Enter> again to
disabled password.
Change Supervisor Password
User Access Level [Full Access]
Change User Password
Password Check [Setup]
User Access Level (Full Access]
This item allows you to select the access restriction to the Setup items.
Configuration options: [No Access] [View Only] [Limited] [Full Access]
No Access prevents user access to the Setup utility.
View Only allows access but does not allow change to any field.
Limited allows changes only to selected fields, such as Date and Time.
Full Access allows viewing and changing all the fields in the Setup
utility.
Change User Password
Select this item to set or change the user password. The User Password
item on top of the screen shows the default Not Installed. After you set a
password, this item shows Installed.
To set a User Password:
1.
Select the Change User Password item and press <Enter>.
2.
On the password box that appears, type a password composed of at
least six letters and/or numbers, then press <Enter>.
3.
Confirm the password when prompted.
The message “Password Installed” appears after you set your password
successfully.
To change the user password, follow the same steps as in setting a user
password.
Clear User Password
Select this item to clear the user password.
ASUS T3-P5G965
5-31
Password Check [Setup]
When set to [Setup], BIOS checks for user password when accessing the
Setup utility. When set to [Always], BIOS checks for user password both
when accessing Setup and booting the system.
Configuration options: [Setup] [Always]
5.7
Tools menu
ASUS EZ Flash 2
ASUS O.C.Profile
5.7.1 ASUS EZ Flash 2
Allows you to run ASUS EZ Flash 2. When you press <Enter>, a
confirmation message appears. Use the left/right arrow key to select
between [Yes] or [No], then press <Enter> to confirm your choice. See
page 5-2, section 5.1.2 for details.
ASUSTek EZ Flash 2 BIOS ROM Utility V3.00
FLASH TYPE: MXIC 25L8005
Current ROM
BOARD: P5B-BN T3-P5G965
VER: 0403
DATE: 10/16/06
Update ROM
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
A:
Note
5-32
[Enter] Select or Load
[B] Backup
[Tab] Switch
[Up/Down/Home/End] Move
[ESC] Exit
Chapter 5: BIOS setup
5.7.2 ASUS O.C. Profile
This item allows you to store or load multiple BIOS settings.
BIOS SETUP UTILITY
Tools
O.C. PROFILE Configuration
O.C. Profile 1 Status
O.C. Profile 2 Status
: Not Installed
: Not Installed
Save to Profile 1
Load from Profile 1
Save to Profile 2
Load from Profile 2
Start O.C. Profile
Enter
F1
F10
ESC
Select Screen
Select Item
Go to Sub Screen
General Help
Save and Exit
Exit
v02.58 (C)Copyright 1985-2006, American Megatrends, Inc.
Save to Profle 1/2
Allows you to save the current BIOS file to the BIOS Flash. Press <Enter> to
save the file.
Load from Profile 1/2
Allows you to load the previous BIOS settings saved in the BIOS Flash.
Press <Enter> to load the file.
Start O.C. Profile
Allows you to run the utility to save and load CMOS. Press <Enter> to run
the utility.
ASUSTek O.C. Profile Utility V1.00
FLASH TYPE: MXIC 25L8005
Current CMOS
BOARD: P5B-BN T3-P5G965
VER: 0403
DATE: 10/16/06
Restore CMOS
BOARD: Unknown
VER: Unknown
DATE: Unknown
PATH: A:\
A:
Note
[Enter] Select or Load
[B] Backup
[Tab] Switch
[Up/Down/Home/End] Move
[ESC] Exit
• This function can support devices such as USB flash disk or floppy
disk with FAT 32/16 format only.
• DO NOT shut down or reset the system while updating the BIOS to
prevent the system boot failure!
ASUS T3-P5G965
5-33
5.8
Exit menu
The Exit menu items allow you to load the optimal or failsafe default values
for the BIOS items, and save or discard your changes to the BIOS items.
Exit Options
Exit & Save Changes
Exit & Discard Changes
Discard Changes
Load Setup Defaults
Pressing <Esc> does not immediately exit this menu. Select one of the
options from this menu or <F10> from the legend bar to exit.
Exit & Save Changes
Once you are finished making your selections, choose this option from the
Exit menu to ensure the values you selected are saved to the CMOS RAM.
An onboard backup battery sustains the CMOS RAM so it stays on even
when the PC is turned off. When you select this option, a confirmation
window appears. Select OK to save changes and exit.
If you attempt to exit the Setup program without saving your changes,
the program prompts you with a message asking if you want to save
your changes before exiting. Press <Enter> to save the changes while
exiting.
Exit & Discard Changes
Select this option only if you do not want to save the changes that you
made to the Setup program. If you made changes to fields other than
System Date, System Time, and Password, the BIOS asks for a confirmation
before exiting.
Discard Changes
This option allows you to discard the selections you made and restore the
previously saved values. After selecting this option, a confirmation appears.
Select OK to discard any changes and load the previously saved values.
Load Setup Defaults
This option allows you to load the default values for each of the
parameters on the Setup menus. When you select this option or if you
press <F5>, a confirmation window appears. Select OK to load default
values. Select Exit & Save Changes or make other changes before saving
the values to the non-volatile RAM.
5-34
Chapter 5: BIOS setup

advertisement

Related manuals

Download PDF

advertisement