18SP310

18SP310
18SP310 – Series 60® Cylinder Block Plug and
Dowel Locations
The customer must install the following shippedloose parts:
I.
8929432 Plug, Rubber Weep Hole (6 places)
J.
8929153 Dowel, 20.0 mm (Diamond)
K. 8929152 Dowel, 20.0 mm (Round)
L. 8929022 Dowel, 16.0 mm (Diamond, 2 places)
M. 8929015 Dowel, 16.0 mm (Round)
Dowels J, K, L, and M are installed to a height of 12.0
mm± 0.5 mm (0.472” ± 0.020”). Use Kent-Moore® tool
J 46224-1 to install dowels J and K. See Figure 1 for
orientation of dowels J and K.
Figure 1
Figure 2
Orientation of Dowels L and M
Figure 3
Orientation of Dowels L and M
Orientation of Dowels J and K
Use J Tool J 36224-2 to install dowels L and M.
See Figure 2 and Figure 3 for orientation of dowels L
and M.
The following plugs are installed in this cylinder
block: (installation instructions are included in
case the plugs are later removed)
18SP310 Page 1 of 2
N. 5139991 Cup Plug, 1-1/2” Stainless (5 places).
See Figure 4 for cup and pipe plug locations.
Cup Plugs N are installed 2.5-3.0 mm (0.098-0.118 in.)
below the machined surface. [Use tool set J 35653 to
install the cup plugs. Coat the outside sealing edge of
the cup plugs with a good grade of non-hardening
sealant such as Loctite® 620 (or equivalent) before
installing.]
Figure 5
Location of Cup and Pipe Plugs on Left
Side
O2. 8922327 ¼”–18 Pipe Plug (1 place). Opposite oil
level dipstick location. See Figure 4.
Figure 4
Location of Cup and Pipe Plugs on
Right Side
O. 8922327 ¼”–18 Pipe Plug (4 places). [Tighten to
19-24 N·m (14-18 lb·ft) torque.]
O1. 8922327 ¼”–18 Pipe Plug (2 places). [Required
only for pressure testing of cylinder block. In
service, these plugs are replaced by the oil
pressure sensor (OPS) and the oil temperature
sensor (OTS).] See Figure 5.
P. 8929594 3/8”–18 Pipe Plug (1 place). [Tighten to
24-31 N·m (18-23 lb·ft) torque.]
P1. 8924517 3/8”-18 Pipe Plug (3 places). [Tighten to
24-31 N·m (18-23 lb·ft) torque.]
Q. 8923916 ½”-14 Pipe Plug (1 place). [Tighten to
31-39 N·m (23-29 lb·ft) torque.]
S. 8924140 Draincock ¼” Pipe Brass.
T. 5151272 Plug 11/32” Dia. [Install flush to 1.0 mm
(0.040 in.) below surface.]
W. 5139988 Cup Plug, 1” Dia. Stainless (2 places).
[Cup Plugs W are installed 2.5-3.0 mm (0.0980.118 in.) below the machined surface. Use tool
set J 35653 to install the cup plugs. Coat the
outside sealing edge of the cup plugs with a good
grade on non-hardening sealant such as Loctite®
620 (or equivalent) before installing.]
© Copyright 2004 Detroit Diesel Corporation. All rights reserved. Detroit Diesel and the spinning arrows design are registered trademarks of
Detroit Diesel Corporation. Kent-Moore is a registered trademark of SPX Corporation. Loctite is a registered trademark of Loctite Corporation.
18SP310 0405 As technical advancements continue, specifications will change. Printed in U.S.A.
18SP310 Page 2 of 2
Was this manual useful for you? yes no
Thank you for your participation!

* Your assessment is very important for improving the work of artificial intelligence, which forms the content of this project

Download PDF

advertisement