Schlage Wireless Locks

User Guide

Contents

Programming and User Codes .......................................... 2

Programming Code ........................................................... 2

User Codes ....................................................................... 2

Turn Lock Feature ............................................................... 2

Replacing the Batteries ...................................................... 3

BE369 Deadbolt ................................................................ 3

FE599 Lever Lock ............................................................. 3

Restoring Factory Settings ................................................ 4

Vacation Mode ..................................................................... 4

Manual Programming ......................................................... 4

Manual Programming Functions ....................................... 5

Emergency Key Override ................................................... 6

BE369 ................................................................................ 6

FE599 ................................................................................ 6

Troubleshooting .................................................................. 6

Lock Parts

Keypad

• Located on the outside of the lock.

• Used to enter codes for programming and unlocking.

Thumbturns

• On the BE369 Deadbolt only.

BE369 Deadbolt

• The inside thumbturn may be rotated at any time to retract (unlock) or extend (lock) the bolt.

• The outside thumbturn can be rotated to retract the bolt after a valid user code has been entered.

• The outside thumbturn can also be rotated to extend the bolt after the

Schlage button has been pressed when Turn Lock feature is enabled.

Lever

• On the FE599 Lever Lock only.

• The inside lever can be rotated at any time to retract the latch.

• The outside lever can be rotated at any time, but will only retract the latch when the lock is unlocked.

Cylinder

• Located on the outside of the lock.

• Used only in emergency situations to unlock the lock. See

Emergency Key Override on page 6 for more information.

Lock and Unlock Buttons

• On the FE599 Lever Lock only.

• Used to put the lock in a locked or unlocked state.

• When these buttons are used, the lock will remain locked or unlocked until locked or unlocked using the buttons, web interface or phone application.

FE599 Lever Lock

Lock and Unlock Light

• On the FE599 Lever Lock only.

• Lights red when inside lock button is pressed.

• Lights green when inside unlock button is pressed.

• Lights only when an inside button is pressed. Does not remain lit.

Programming and User Codes

All locks are pre-programmed with a programming code and two user codes. The programming code and user codes can be changed at any time.

All pre-programmed codes can be found on the yellow sticker on the front of the

Installation Instructions that come with the lock. An identical label is also located on the inside (part that faces the door) of the keypad.

Programming Code

• Used to manually program the lock using the keypad.

• Used to put the lock into enrollment mode.

• Can only be changed by manually using the keypad. See

Manual

Programming Functions on page 5 for more information.

• CANNOT be used to unlock the lock.

• CAN be used to take a lock out of vacation mode at the

keypad. See Vacation Mode on page 4 for more information.

• If you change your programming code and then forget it, you

can reset your lock back to factory settings. See Restoring

Factory Settings on page 4 for more information.

• The web interface is not affected by a change to the programming code.

User Codes

• Used to unlock the lock.

• May be added and deleted manually, using the keypad.

• User codes are assigned to names in the web portal and can be changed, added or deleted using the web portal.

• If you add a new code to the lock manually, the new code will be displayed on the web portal with an assigned name of New User (#) , which can be changed at any time.

Turn Lock Feature

When the Turn Lock feature (available on BE369 Deadbolt only) is disabled, a valid user code must be entered at the keypad in order to lock the lock from the outside.

The Turn Lock feature is enabled by default.

See

Manual Programming Functions on page 5 for instructions to disable this feature.

2

Replacing the Batteries

BE369 Deadbolt

a. Remove cover screws.

b. Remove screw on upper left to release upper battery tray.

Hold battery tray in place while loosening screw.

c. Upper battery tray will be released. Fully remove tray and remove three old AA batteries.

d. Remove 9V battery. e. Remove the 9V connector from the old 9V battery.

f. Replace all batteries with new, high-quality batteries.

Reverse steps to replace battery tray and cover. Be careful not to pinch wires when replacing the cover.

FE599 Lever Lock

a. Remove cover screws.

b. Remove cover.

c. Remove battery cover.

d. Remove four old AA batteries.

e. Replace batteries with 4 new, high-quality AA batteries.

Reverse steps to replace the battery cover and lock cover.

3

Restoring Factory Settings

Restoring the factory settings will:

• Restore the original programming code

• Restore the pre-programmed user codes

If you have an active account at www.schlagelink.com, the user codes listed in the web interface for the lock will be restored in the physical lock when lock reconnects with the bridge. The original pre-programmed user codes will also be added to the web interface.

Restoring factory settings WILL NOT exclude the lock from the bridge.

DO NOT reset your lock unless you are able to locate the original programming code. Customer service cannot retrieve a lost programming code.

1. For FE599, disconnect the batteries. For BE369, disconnect the 9V battery.

2. On the lock keypad, press and release the Schlage button.

3. Reconnect the battery and wait until the Schlage button is no longer lit.

4. Within ten (10) seconds, press and hold the Schlage button until it lights green and the lock beeps.

Vacation Mode

Vacation mode is used to disable all user codes at the keypad. If a valid user code is entered while the lock is in vacation mode, the

Schlage button will first light green and then red, and the lock will not unlock.

If you will be away from your home for a period of time in which no one should have access to your lock, it is a good idea to use vacation mode to prevent repeated access attempts.

Vacation mode can be disabled at the keypad by entering the six-digit programming code.

Manual Programming

During normal operation, Schlage Wireless Locks should be managed through the web interface at www.schlagelink.com.

If internet access is temporarily lost, changes to the lock can be entered manually at the lock’s keypad. When Internet access is restored, the lock

will automatically update the web interface with any changes. See Manual Programming Functions on page 5 for more information.

Lights/Beeps Legend

Three Lights and Three Beeps 1

One Long Flash and One Long Beep 1

One Long Flash and Two Beeps 1

Step Confirmation

• A correct entry was made during programming and accepted by the lock.

Function Confirmation

• A set of steps was completed successfully.

Error

• An incorrect entry was made during programming.

• For other errors, see the troubleshooting section.

Backlight

• Entire keypad glows blue during programming and when the Schlage button is pressed before pressing any codes.

Programming Legend

Programming Code (six numbers)

• See Programming Code on page 2 for

more information.

Schlage Button

• Used for programming

• Used to turn on the backlight

User Code (four numbers)

• See User Codes on page 2 for more

information

Keypad Numbers

• Used for programming

• Used to enter a user code to unlock the lock

1 Beeps will sound only when the beeper is turned on. Low battery beeps will sound even when the beeper is disabled.

4

Manual Programming Functions

Press the keys on the keypad as shown in the following steps. Wait for the confirmation indicator before proceeding to the next step. If you make a mistake, wait for all lights and beeps to stop and then start over from the beginning.

Press

Add

Press

(Six

Numbers)

Wait For Wait For

Press New

(Four

Numbers)

Wait For

Press Same New

(Four

Numbers)

Success!

Delete

Change

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

Wait For

3 Lights + 3 Beeps

Press

Wait For

3 Lights + 3 Beeps

Press Unwanted

(Four

Numbers)

Wait For

3 Lights + 3 Beeps

Press New

(Six

Numbers)

Wait For

1 Long Light + 1 Long Beep

Press Same Unwanted

(Four

Numbers)

Success!

1 Long Light + 1 Long Beep

Press Same New

(Six

Numbers)

Success!

3 Lights + 3 Beeps

Enable Vacation

Mode

(Disable All)

Enable/Disable

Beeper

Delete All 2

Enable/Disable 3

Turn Lock Feature

Put Lock in

Enrollment Mode 4

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

Press

(Six

Numbers)

Wait For

3 Lights + 3 Beeps

3 Lights + 3 Beeps

Press

Success!

1 Long Light + 1 Long Beep

Press

Success!

1 Long Light + 1 Long Beep

Press

Wait For

3 Lights + 3 Beeps

Press

Success!

1 Long Light + 1 Long Beep

Press

Success!

Blinking

Disable Vacation

Mode

(Enable All 1 )

Press

(Six

Numbers)

Success!

1 Long Light + 1 Long Beep

1 Long Light + 1 Long Beep

Press

(Six

Numbers)

Success!

1 Long Light + 1 Long Beep

1

2

3

4

Enable All User Codes function is available only when user codes are currently disabled.

Delete All User Codes function will remove ALL user codes, but will not change the programming code. User Codes cannot be recovered after this function is completed.

The Turn Lock Feature is available only on the BE369 (deadbolt). When this feature is disabled, a valid user code must be entered in order to lock the lock from the outside. The Turn Lock feature is enabled by default.

Bridge must be put into enrollment mode before lock for successful enrollment/exclusion.

5

Emergency Key Override

If the battery fails completely, or if there is an electronic error, the lock can be unlocked manually using the key.

BE369

FE599

Troubleshooting

Problem Lights/Beeps Cause Solution at Lock Solution on Web

Entering a valid user code using the keypad does not unlock lock.

Schlage button does not light when pressed

Green then

Red/Hi then

Low none

Lock is in vacation mode.

Lock keypad is locked out because too many incorrect codes have been entered.

Battery is dead.

Enter six-digit programming code.

Uncheck Vacation checkbox.

Replace battery. See

Replace the Battery.

none

There is a delay before the lock unlocks after a valid user code is entered.

The Schlage button blinks red, even when no buttons have been pressed.

Red then

Green/Low then

Hi

Fast red blink.

Battery is critically low.

Cannot add a new user code. Red (when attempted via keypad) none (when attempted via web)

Battery is low.

Replace battery. See

Replace the Battery.

Replace battery. See

Replace the Battery.

none none

19 user codes already exist.

Delete at least one existing user code. Then add

When adding a user at the keypad, the first user code entry did not match the second.

First four digits match first four digits of the programming code.

new user code.

Try again. Make sure you enter the same code twice.

Change the programming code or select a different user code to add.

none

Select a different user code to add.

Select a different user code.

Cannot delete a user code at the keypad.

Red

User code already exists in lock.

The first user code entry did not match the second.

Wait 30 seconds and try again.

Try again. Make sure you enter the same code twice.

none none

6

Problem

Cannot change the programming code.

Cannot delete all user codes at the keypad.

Pressing the Schlage button when the deadbolt is unlocked does not allow locking (deadbolt only).

Thumbturn does not spin freely when deadbolt is locked (deadbolt only).

Pressing the Schlage button when deadbolt is locked unlocks the deadbolt

(deadbolt only).

Lights/Beeps Cause

Red

Red none none

Solution at Lock

User code already in lock matches the first four digits of the programming code you are trying to add.

Select a different programming code, or delete the user code that matches the first four digits you want to use.

The first programming code entry did not match the second.

The first programming code entry did not match the second.

Try again. Make sure you enter the same code twice.

Try again. Make sure you enter the same code twice.

Turn Lock feature is disabled. Enable the Turn Lock feature.

See

Manual Programming

Functions on page 5 for

more information.

Deadbolt is malfunctioning.

Call Customer Service at

(877) 288-7707.

Solution on Web

none none none none none none

Thumbturn is difficult to rotate or does not rotate smoothly (deadbolt only).

none

After entering a valid code on the deadbolt keypad, Schlage button flashes green and then amber. Otherwise, lock appears to function normally

(deadbolt only).

Green then

Orange

Lock was installed improperly. Cam needs to be rotated to proper position. Check step

7 in the deadbolt installation instructions (located at part2.

schlage.com

).

Deadbolt was not adjusted to the correct backset position.

AA batteries need to be replaced.

Deadbolt needs to be adjusted to correct position.

Check step 3 in the deadbolt installation instructions

(located at part2.schlage.

com ).

Replace AA batteries.

Replacing the Batteries on page 3 for more information.

none none none

©2009 Schlage Lock Company lock user guide Rev. 06/09-b